PRESS BRAKE CENTRAL BLOCK
PRESS MANIFOLD (Ed. 07/2012) Page 1/18
PRESS BRAKE CENTRAL BLOCK
PRESS MANIFOLD (Ed. 07/2012) Page 2/18
PRESS BRAKE CENTRAL BLOCK
PRESS MANIFOLD (Ed. 07/2012) Page 3/18
SUMMARY Cap. 1 Basic Instruction Page 4 Cap. 2 Working parameters Page 5 Cap. 3 Option one – Single poppet valve Page 6 Cap. 4 Option two – Middle safety level Page 7 Cap. 5 Option three – High safety level Page 8 Cap. 6 Part List Page 9 Cap. 7 Sequence Diagram Page 10 Cap. 8 Central Block CAD View Page 11 Cap. 9 Overall Dimensions of Block Page 12 Cap. 10 CFP Suction Valve Page 13
Cap. 10.1 Performance Page 13 Cap. 10.2 Opening and Piloting Pressure Page 13 Cap. 10.3 Identification Code Page 14 Cap. 10.4 Characteristic Curves with Suction Flow from A-B Page 14 Cap. 10.5 Overall Dimensions Page 15 Cap. 10.6 Installation Page 16
Cap. 11 RFP Suction Valve Page 17 Cap. 12 Ordering Form Page 18
PRESS BRAKE CENTRAL BLOCK
PRESS MANIFOLD (Ed. 07/2012) Page 4/18
1. BASIC INSTRUCTION The hydraulic system from Duplomatic Oleodinamica S.p.A. was designed for CNC
controlled press brakes, especially for pressing forces up to 3.000 kN The horizontal distance between the two pressing cylinders should be 3.500 mm
max The system and all its components are designed uniquely for press brakes
applications, and should be installed by qualified personnel It is essential to adhere strictly to the installation and operation instructions of the
products before commissioning the hydraulic system Make sure that all hydraulic components are mounted in the correct way
Check the fluid level in the tank within a few hours after start-up to detect any
possible fluid loss After the first 100 hours, observe the filter contamination and calibration, and
remember that every 3.000 hours of operation, hydraulic fluid and filter elements should be substituted
PRESS BRAKE CENTRAL BLOCK
PRESS MANIFOLD (Ed. 07/2012) Page 5/18
2. WORKING PERFORMANCE
Maximum operating pressure bar 320 Maximum flow rate l/min 95 Operating limits check Electrical connections check Ambient temperature range ° C - 10 / + 50 Fluid temperature range ° C 0 / + 60 Fluid viscosity range cSt 20 ÷ 400 Recommended viscosity cSt 25 Fluid contamination degree According to ISO 4406: 1999 class 20/18/15 Hydraulic fluid Mineral oil according to DIN 51524, other types on request
PRESS BRAKE CENTRAL BLOCK
PRESS MANIFOLD (Ed. 07/2012) Page 6/18
3. OPTION ONE – SINGLE POPPET VALVE
The most economic solution for press brake market, without monitored valves and single poppet for leak free operations.
PRESS BRAKE CENTRAL BLOCK
PRESS MANIFOLD (Ed. 07/2012) Page 7/18
4. OPTION TWO – MIDDLE SAFETY LAVEL
The option offers leak free operation with single poppet and balancing valves for optimal control.
PRESS BRAKE CENTRAL BLOCK
PRESS MANIFOLD (Ed. 07/2012) Page 8/18
5. OPTION THREE – HIGH SAFETY LEVEL (Double poppet version – CE Suitable) Two poppet valves makes the system a highly reliable and leak free operation under all circumstances. Monitored valve offers high level of security.
PRESS BRAKE CENTRAL BLOCK
PRESS MANIFOLD (Ed. 07/2012) Page 9/18
6. PART LIST Numbers 1, 2 and 3 represent the 3 available options and respective components. ITEM CODE COMPONENT 1 2 3
1 LC16-PS2/20N LOGIC ELEMENT X X X
2 LP16DPE6/20N LOGIC ELEMENT X X X
3 PRED3-350/10N-D24K1 PROP. PRESSURE VALVE X X X
6 DSE3-C16/10N-D24K1 PROP. DIRECTIONAL VALVE X X X
8 DS3M-TA/10N-D24K1 MONITORED DIRECTIONAL VALVE * - - X
9 CR4/22N RELIEF VALVE - X X
10 EMC-3416-NC-0-24C MONITORED POPPET VALVE * - - X
11 RESTRICTOR VSTA M6X8 RESTRICTOR X X X
12 CR6/22N RELIEF VALVE X X X
13 RESTRICOTR VSTA M6X8 RESTRICTOR X X X
14 MAIN MANIFOLD PRESS BRAKE MAIN MANIFOLD PRESS BRAKE X X X
15 PRESA DI PRESS.PN630 G1/4 PRESSURE READING POINT X X X
16 NG06 BALANCING MANIFOLD NG06 BALANCING MANIFOLD - X X
17 KT08-2NC/10N-D24K1 POPPET VALVE X - X
* This item in option 1 & 2 will be replaced by non-monitored version or removed completely.
PRESS BRAKE CENTRAL BLOCK
PRESS MANIFOLD (Ed. 07/2012) Page 10/18
7. SEQUENCE DIAGRAM
Items 010 (S1/S2) are present only in option 1 and 2 Items 017 (S3/S4) are present only in option 2 and 3
PRESS BRAKE CENTRAL BLOCK
PRESS MANIFOLD (Ed. 07/2012) Page 11/18
8. CENTRAL BLOCK CAD VIEW
6* 6*
10*
12
16
10*
17 17
8*
1+2+3
14
PRESS BRAKE CENTRAL BLOCK
PRESS MANIFOLD (Ed. 07/2012) Page 12/18
9. OVERALL DIMENSIONS OF THE BLOCK
PRESS BRAKE CENTRAL BLOCK
PRESS MANIFOLD (Ed. 07/2012) Page 13/18
10. CFP SUCTION VALVES The CFP valves are pilot operated check valves, expressly designed for hydraulic presses, to allow easy filling and emptying of the press cylinder during the rapid down and up strokes. They are “sandwich” mounted, to be installed directly between the suction flange (connected to the tank), and the cylinder.
A version with pre-opening device is available. Connected to the X pilot port allows circuit decompression before the cylinder raising phase begins.
The CFP valves are available in seven different sizes with max flow up to 2.500 l/min. 10.1 PERFORMANCE
10.2 OPENING AND PILOTING PRESSURE
PRESS BRAKE CENTRAL BLOCK
PRESS MANIFOLD (Ed. 07/2012) Page 14/18
10.3 IDENTIFICATION CODE
10.4 CHARACTERISTIC CURVES WITH SUCTION FLOW FROM A-B
PRESS BRAKE CENTRAL BLOCK
PRESS MANIFOLD (Ed. 07/2012) Page 15/18
10.5 OVERALL DIMENSIONS
PRESS BRAKE CENTRAL BLOCK
PRESS MANIFOLD (Ed. 07/2012) Page 16/18
10.6 INSTALLATION
NOTE A: Calculated diameters for PN 16 – DIN 2448 steel pipes. NOTE B: For applications with standard connection flanges type UNI 2284, UNI 2285, UNI 2286, special bushings to fit on fastening bolts must be provided in order to ensure a correct valve mounting. For information about the installation with UNI connectors flanges, please consult our technical department.
PRESS BRAKE CENTRAL BLOCK
PRESS MANIFOLD (Ed. 07/2012) Page 17/18
11. RFP SUCTION VALVE The normally open logic elements are used as suction or filling valves. Improved design based on our logic valve LC-*A. Made by 2-way cartridge valve with ISO 7368/DIN 24342 cavity bore.
The cartridge valve has an area ratio 5,1
1
3
1 AA . The poppet (1) is normally open thanks to
the spring (2). The poppet closes when the piloting pressure acting on area A3 is higher on area A1 (pressure on A port), or on area A2 (pressure on B port), added to the spring load value. Valve seat dimensions according to ISO 7368/DIN 24342.
PRESS BRAKE CENTRAL BLOCK
PRESS MANIFOLD (Ed. 07/2012) Page 18/18
12. ORDERING FORM
COMPANY Address Phone Fax www P.I.C. Phone e-Mail
VERTICAL PRESS INFORMATION
PRESSING FORCE kN MAIN CYLINDER – PISTON DIAMETER mm FAST DOWN SPEED mm WORKING SPEED mm/s FAST RETURN SPEED mm/s BEAM WEIGHT TOOLS INCLUDED kg
OPTIONS
1) Upper tool clamping Yes______________________ bar No
2) Used CNC-control
Make _______________ Type ________________
3) Lower tool clamping Yes______________________ bar No 4) Proportional hydraulic crowning Yes______________________ bar No