PVSYST SA - Route du Bois-de-Bay 107 - 1242 Satigny - Suissewww.pvsyst.com
Any reproduction or copy of the course support, even partial, is forbidden without a written authorization of the author.
PVsysts new framework to simulate bifacial systems
PVPMC Workshop
24-26.10.2016 Freiburg, Germany
André Mermoud, Bruno WittmerBruno.Wittmer@pvsyst .com
Page 2Page 2
Overview
• Introduction– Bifacial PV modules
– Modelling the backside irradiance
• PVsyst Approach do model bifacial installations– Model describing shed installations
– Calculation of backside irradiation
– Some first qualitative results
• Summary and Outlook
Page 3Page 3
Approach for Bifacial Modules in PVsyst
Treatment of bifacial modules
• Front side irradiance is added to backside irradiance x bifaciality factor (default is 0.8)
• From this Effective irradiance follows the IV-curve.• Loss factor describing shadings of mounting structure
and junction boxes• An additional mismatch factor is foreseen to account
for inhomogeneous rear side illumination• This approach is an approximation
The main challenge is to calculate the additional backside irradiance including its inhomogeneity
Front side irradianceBack side irradiance
xbifaciality factor
Effective irradiance
IV-Curve
Page 4Page 4
Standard Irradiance Calculation
• DirectSubject to near shadings depending on sun position
• DiffuseSubject to shading factor that is constant for a given plane orientationCalculation of angles that shade the diffuse
• AlbedoSubject to shading factor that is constant for a given plane orientationCalculation of azimuth angles that are blocked
Irradiance on PV modules has 3 components
Shadings of the direct irradiance Shadings of the diffuse irradiance
Azim 0° Azim -20° Azim -40°
He 10°
He 20°
. . .
. . . Diffuse shading factor is an integral over all hemisphere directions
Page 5Page 5
Albedo and Near Ground Scattering
• Albedo (of transposition model)Reflections and scattering from ground that is far away.Obstacles will shade all the albedo for a given azimuth.
• Near Ground Scattering (for bifacial simulations)Light scattered back from ground that is close to the PV modules.Subject to near shadings with solid angle calculation.
Albedo is not the same as Near Ground Scattering
Bifacial PV installations can not be described by a modified albedo only..
Albedo scattering
Albedo visible
Albedo shaded
Near ground scattering
Ground scattering is only partially shaded
Page 6Page 6
Systems with Bifacial Modules in PVsyst
Basic approach for bifacial modelling
• Fraction of direct irradiance that reaches the scattering ground (depends on sun position)
• Fraction of diffuse irradiance that reaches the scattering ground (single factor)
• Factor describing the scattering off the ground (Ground Albedo)
• Factor for backside acceptance of scattering ground (form factor)
• (Constant loss factor describing shadings of mounting structures, cabling and junction boxes)
• Only light scattered back from the ground contributes to backside illumination.• Direct and sky diffuse irradiance contribute to ground illumination• Sky diffuse is isotropic• Only scattering is considered (no specular reflections)• The diffuse reflection is isotropic (Lambertian Surface)• Non-homogeneous illumination of backside is neglected at this stage
Assumptions for bifacial calculation
Sketch explaining bifacial model
Direct Irradiance
Diffuse Irradiance
Ground Scattering
Bifacial Module
Incoming light, and light scattered back to modulesdepend on the position
Page 7Page 7
Bifacial modules in PV installations
• Vertical mountingDiffuse and direct light can reach the PV module on both sides.
Bifacial modules are used in different situations
Sketch showing vertical bifacial systems
In a first step, PVsyst will model bifacial systems only for shed geometries.
Sketch showing shed bifacial systems
• ShedsLight can reach the ground between the sheds and scatter back to the module backside.
Page 8Page 8
Bifacial Modules in Sheds
PVsyst Model to determine bifacial parameters for regular shed configurations
Simplified 2D calculationRows without boundary effects (infinitely long)Parameters:• Tilt, Azimuth• Width, Pitch• Height above ground• Ground AlbedoThe factors for the bifacial calculation can be determined by integrating over the distance between rowsDirect and sky diffuse are only computed for front side.Near ground scattering is only computed for backside.
Calculation proceeds in three steps1. Ground Acceptance of
direct light2. Ground acceptance of
diffuse light3. Backside acceptance of
ground (form factor)
Page 9Page 9
Calculation of Direct Light on GroundGround Acceptance of direct light
1. Profile Angle and Limit Angle determine the amount of directly illuminated ground surface
2. Height over ground and profile angle determine the position of the illuminated strips.
Limit Angle
P
q alim
tan𝛼𝑙𝑖𝑚 =sin 𝜃
𝑃𝑊 − cos 𝜃
aprof
Profile angle
Azimuth a
Profile angle aprof
Page 10Page 10
Examples of Direct Light Ground Acceptance
Ground Acceptance of direct light
Ground irradiance over one day
Momentary Ground irradiance
Geneva, 21. June, 19:00h
Geneva, 21. June, 12:00h 21. June
Illuminated ground is composed of homogeneously illuminated strips
Page 11Page 11
Calculation of Diffuse Irradiance on GroundGround acceptance of diffuse light
- Diffuse irradiance from sky is isotropic.- Ground acceptance of diffuse light is a
function of the position on the ground.- Underneath the sheds the irradiance is
smaller.- Inhomogeneity tends to level out with
increasing mounting height.
sheds at ground level 1m over ground 2m over ground
Page 12Page 12
Calculation of Form FactorBackside acceptance of ground
(Form Factor)
Ground scattering is isotropic(Lambertian Scattering)
sheds at ground level 1m over ground 2m over ground
- Ground scattering is isotropic (Lambertian Scattering)
- Form Factor is a function of the position on the ground.
- Underneath the sheds the form factor is large.
- Inhomogeneity tends to level out with increasing mounting height.
Page 13Page 13
Calculation of Total Irradiance on BacksidePutting it all together
Direct Diffuse
Irradiance on Ground is specific for location and geometry.In this case (Geneva): - Almost no direct in winter- Fraction of diffuse on ground
is constant over the year
Irradiance on Backside:
Combine Ground acceptance with Form Factor
+
Irradianceon ground
Absolute irradiance Normalized to horizontal
Absolute irradiance Normalized to Front
For this location and geometry, the additional bifacial gain isobtained mainly in summer
Page 14Page 14
Example shed installationBasic PV system with sheds:
90 kWp in 6 rows of 3 x 20 modules landscapeLocation Geneva, Switzerland: 46.3° N, 6.1° E25° Tilt, 6m Pitch, 3m WidthMounted 1m over groundPV surface: 600 m2
Ground surface: 33m x 33m = 1000 m2
3D shading scene
Definition of bifacial shed model
Page 15Page 15
Simulation ResultsPVsyst Report showing results for bifacial modelling
Global incident on groundGround scatteringBackside form factorShadings on backsideBifaciality factorMismatch for back irradiance
Page 16Page 16
Height over groundHeight over ground
With higher mounting, the opposite behavior of ground illumination and acceptance gets attenuated.For the shed model with no boundaries (infinitely long sheds), the increase saturates (ground will appear homogeneously illuminated)
sheds at ground level
1m over ground
2m over ground
Diffuse on Ground Form Factor Diffuse Contribution to rear side
Page 17Page 17
Impact on best Tilt
Impact on best tilt
Best tilt does not change significantly for this specific case.Maximum in bifacial curve is slightly flatter.Bifacial definitions:- 2 m over ground- 80% bifaciality factor- GCR: 50%- Ground albedo factor: 0.3
Bifacial ContributionOn Rear Side
Page 18Page 18
Impact of pitch on bifacial gain
Gain increase as function of pitch
Increase of pitch (row spacing) reduces mutual shadings and thus increasing the yield.Ground in between rows also gets more irradiance, leading to an increased yield gain for bifacial systems.
4%
3%
Normalized to monofacial, pitch 5m
Page 19Page 19
Best tilt as function of Pitch
Complete optimization has to consider Tilt together with Pitch
Optimization tool to study yield as function of tilt and pitch
Monofacial Bifacial
Page 20Page 20
Ground reflection (Albedo factor)
Bifacial Gain as function of Albedo Factor
For common Albedo factor ranges and the considered 90 kWp shed installation, the simulation predicts 4-10% bifacial gain.
Ground Type Albedo
factor
Worn Asphalt 0.12
Bare Soil 0.17
Green Grass 0.25
Desert sand 0.40
New concrete 0.55
Fresh snow 0.8-0.9
Page 21Page 21
Next Steps for Bifacial Framework
Bifacial treatment of any PVsyst 3D scene
Define a ground surface shape.Compute Global irradiance on ground (direct and Diffuse).Calculate view factors for all PV backsides.Limitations:- No specular reflections- Only the ground surface scatters backStatistical approach with a random distribution of ground points
Add further specific bifacial models
Model for vertically mounted modules- Both module sides need to be treated equally- Irradiance of Direct, Diffuse, Albedo and Ground Scattering computed for
both faces
Page 22Page 22
Summary and Outlook
– The challenge in bifacial calculations for PV systems is to determine the irradiance on the module back side
– The module behavior under a given total effective irradiance is similar to a standard PV module
– Simulation of Bifacial PV systems with shed (row) layout will be possible with PVsyst V6.60
– Several approximations are made to handle the calculation• Only light scattered off the ground reaches the module back side
• Ground reflection is diffuse and isotropic
• Shadings of the mounting structure on the backside are accounted with a constant derate factor
• An additional factor accounts for inhomogeneous illumination
– Main contributions of backside illumination are captured
– The approach will be generalized to allow the bifacial calculation for any 3D shading scene
– The final goal is to treat front and back illumination in the same way.
– Validation with measured data is still necessary