TOP DRIVE DRILLING SYSTEM
SUBSECTION 5: OPTIONAL EQUIPMENT
CANDOC OPTIONAL EQUIPMENT MANUAL SUBSECTION 5: OPTIONAL EQUIPMENT
COPYRIGHT © 2004 CANRIG DRILLING TECHNOLOGY LTD.
ALL RIGHTS RESERVED
This Top Drive System is protected by one or more of the following US patents and foreign counterparts: US 4,478,291 * US 4,951,709 * US 5,251,709 * US 6,024,181 and other patents pending.
Information in this document is subject to change without notice. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written permission of Canrig Drilling Technology Ltd. Printed in the United States of America.
8/17/2006 Serial Number: 489
SUBSECTION 5H: WASH PIPE & COUPLING TOOL (3” WP)
Assembly Description Drawing Rev
AY11400 WASH PIPE CPLG TOOL ASSY, 3IN AY11400 C
AY11400-1 WASHPIPE CPLG TOOL, 3 IN, PRELIM ASSY AY11400-1 0
AY11679 WRENCH TOOL ASSY, WASHPIPE 3IN AY11679 0
AY11730 WASH PIPE REMOVAL TOOL SET, 3IN NO DRAWING 0
Part: AY11400WASHPIPE CPLG TOOL ASSY, 3 IN
Drawing ID: AY11400 Rev No: C
Item Qty Part ID DescriptionUnits
Engineering Bill of Material
Description:
Eng ID: 0
Eng ID
01 1.00 WASHPIPE CPLG TOOL ASSY, 3 IN, WELDMENTEA AY11400-1 VSA
02 4.00 SAFETY PINEA M24-2000-01003 8.00 WIRE ROPE, 1/16, 7 x 7, STAINLESSFT M21-2000-01004 16.00 FERRULE, 1/16, OVAL, ALUMINIUMEA M19-3006-01005 1.00 TOOL, REMOVAL SUPPORT, WASHPIPEEA DT12826
Printed: 12/30/2003 Page 1 of 1
BYNo. Y/M/D
± .010 IN 5 INCHES± .005 IN 5 INCHES
TOLERANCEREMOVE SHARP CORNERS AND BURRS
± .010 IN 5 INCHESWITHOUT PERMISSION AND RETURNED
CANRIG DRILLING TECHNOLOGY LTD..AND INVENTION ARE RESERVED BYUPON DEMAND. ALL RIGHTS OF DESIGN
REVISION MACHINED SURFACES
PARALLELISMTRUE POSITION
125.005
THAT IT IS NOT TO BE REPRODUCEDFURNISHED WITH THE UNDERSTANDINGTECHNOLOGY LTD.. THIS PRINT ISAND INVENTION OF CANRIG DRILLINGSHOWN THEREON ARE THE PROPERTYTHIS PRINT AND DESIGN AND DETAIL
CASTING
STRAIGHTNESSSQUARENESS
CONCENTRICITY .005 TIR± 1/16
± .005".xxx
± 1°ANGULAR
0 TO 24"> 24"
ANGULAR± 2°
± .06"± .12" SCALEEST. WEIGHT PROJECT
± .015"± .030"
MACHINING IMPERIAL
FABRICATING IMPERIAL
- UNLESS OTHERWISE SPECIFIED
FABRICATING [METRIC]
> 600 mm0 TO 600 mm
DECIMAL± 3 mm± 1 mm
.xx
.x
CHECKED
MATERIALAPPRV'D
DRAWN
REV
TECHNOLOGY LTD.CANRIG DRILLING
AY11400 C
WASHPIPE CPLG TOOL, 3 IN BOREFINAL ASSEMBLY
WELDING PROCEDURE UNLESS OTHERWISE SPECIFIED - ANSI/AWS D1.1-98 OR CSA W59-M1989 DC 02/09/02- -- -
-
60 LBS 1:2 -
IF IN DOUBT......PLEASE ASK!
IF IN DOUBT......PLEASE ASK!
C 03/01/29 JRS ADDED ITEM 5 TO B OF M
RH SIDE VIEW
TOP VIEW
BOTTOM END VIEW
DETAIL A
ISOMETRIC VIEW
0203 04
01
01
03 04
WIRE PIN HEADTHRU THIS CHAIN LINK.LEAVE ENOUGH SLACKTO BE ABLE TO REMOVE PIN.
WIRE PIN HEADTHRU THIS CHAIN LINK
0403
03 04
WIRE BOTH PIN HEADSTHRU THIS CHAIN LINK.LEAVE ENOUGH SLACK TOBE ABLE TO REMOVE PINS.
A
Part: AY11400-1
WASHPIPE CPLG TOOL, 3 IN, PRELIM ASSY
Drawing ID: AY11400-1 Rev No: 0
Item Qty Part ID DescriptionUnits
Engineering Bill of Material
Description:
Eng ID: 0
Eng ID
01 4.00 PLATE, REINFORCEMENT, CPLG TOOL, 3 INEA DT12162-3
03 1.00 TUBE, MACHINING, LHEA DT12162-LH
04 1.00 TUBE, MACHINING, RHEA DT12162-RH
05 4.00 PIN, 3/4 DIA, 3.50 LGEA DT12166
06 12.00 HINGE, WASHPIPE TOOL, 3/4 INEA DT12319
07 1.00 PIN, GAUGE, 3/4 DIA, 3.50 LGEA DT12581
08 2.00 CHAIN, 1/4 GRADE 70EA M10130
Printed: 5/11/2006 Page 1 of 1
BYNo. Y/M/D
± .010 IN 5 INCHES± .005 IN 5 INCHES
TOLERANCEREMOVE SHARP CORNERS AND BURRS
± .010 IN 5 INCHESWITHOUT PERMISSION AND RETURNED
CANRIG DRILLING TECHNOLOGY LTD..AND INVENTION ARE RESERVED BYUPON DEMAND. ALL RIGHTS OF DESIGN
REVISION MACHINED SURFACES
PARALLELISMTRUE POSITION
125.005
THAT IT IS NOT TO BE REPRODUCEDFURNISHED WITH THE UNDERSTANDINGTECHNOLOGY LTD.. THIS PRINT ISAND INVENTION OF CANRIG DRILLINGSHOWN THEREON ARE THE PROPERTYTHIS PRINT AND DESIGN AND DETAIL
CASTING
STRAIGHTNESSSQUARENESS
CONCENTRICITY .005 TIR± 1/16
± .005".xxx
± 1°ANGULAR
0 TO 24"> 24"
ANGULAR± 2°
± .06"± .12" SCALEEST. WEIGHT PROJECT
± .015"± .030"
MACHINING IMPERIAL
FABRICATING IMPERIAL
- UNLESS OTHERWISE SPECIFIED
FABRICATING [METRIC]
> 600 mm0 TO 600 mm
DECIMAL± 3 mm± 1 mm
.xx
.x
CHECKED
MATERIALAPPRV'D
DRAWN
REV
TECHNOLOGY LTD.CANRIG DRILLING
AY11400-1 B
WASHPIPE CPLG TOOL, 3 IN BORE WELDMENT AND PRELIMINARY ASSEMBLY
WELDING PROCEDURE UNLESS OTHERWISE SPECIFIED - ANSI/AWS D1.1-98 OR CSA W59-M1989 DC 02/07/22- -- -
SEE ALSO DWG#AY11400-2
60 LBS 1:2 -
IF IN DOUBT......PLEASE ASK!
IF IN DOUBT......PLEASE ASK!
SIDE VIEW BOTTOM END VIEW
A A
SECTION A-A
1
3
4
B
DETAIL B - TYP 1:1
1
3
6
6
6
0.01 GAP TYP
0.75REF
BOTTOM ENDTOP END
C
DETAIL C1:1
0.56 (NO WELD)TYP - SEE NOTES
TYP 1/4
3
4
6
6
TYP 1/4
TYP1/4
1
4
5
6
D
DSECTION D-D
TYP 1/4
1
3
4
6
1
1
1
CENTEREDON EACH TOOTH
NOTES:
1) WELD ITEM 6 TO ITEMS 3 AND 4 WITH GAUGE PIN (ITEM 07 - DT12581) INSERTED THRU ITEM 6.LOCATE ITEM 6 AS SHOWN IN DETAIL "B". ENSURE THAT ITEMS 3 AND 4 HAVE A 0.06 GAPBETWEEN THEM PRIOR TO WELDING. EACH ITEM 6 SHOULD HALF A 0.010" SHIM BETWEEN THEMPRIOR TO WELDING. DO NOT USE ITEM 5 (DT12166) IN PLACE OF THE GAUGE PIN WHEN WELDINGITEM 6.2) LEAVE 0.56" CLEARANCE FROM WELDS TO ASSURE CLOSING OF THE WASHPIPE TOOL (SEEDETAIL "C").3) CUT ITEM 8 IN HALF AND WELD IN LOCATIONS SHOWN.4) AFTER WELDING, SHOT BLAST AND THEN APPLY MAGNESIUM PHOSPHATE COATING.
CL
SHEET 1 OF 2
5
5
5
5
A 02/6/24 DC ECN#845, 2.50 WAS 2.38, 0.25 R. WAS 0.19 R.
B 02/7/24 DC REDESIGNED ENTIRE TOOL
SEE NOTE 1
SEE NOTE 1
SEE NOTE 1
SEE NOTE 1
UP
STAMP ARROW AND "UP"BOTH HALVES1/4" LETTERS
0.25 TYP
7.38
DIA
REF
0.06 GAP
1.56 TYP
3
6.00
8
88
4.65 TYP
88
8
3
TYP 1/8
34°
32° TYP
SEE NOTE 3
BYNo. Y/M/D
± .010 IN 5 INCHES± .005 IN 5 INCHES
TOLERANCEREMOVE SHARP CORNERS AND BURRS
± .010 IN 5 INCHESWITHOUT PERMISSION AND RETURNED
CANRIG DRILLING TECHNOLOGY LTD..AND INVENTION ARE RESERVED BYUPON DEMAND. ALL RIGHTS OF DESIGN
REVISION MACHINED SURFACES
PARALLELISMTRUE POSITION
125.005
THAT IT IS NOT TO BE REPRODUCEDFURNISHED WITH THE UNDERSTANDINGTECHNOLOGY LTD.. THIS PRINT ISAND INVENTION OF CANRIG DRILLINGSHOWN THEREON ARE THE PROPERTYTHIS PRINT AND DESIGN AND DETAIL
CASTING
STRAIGHTNESSSQUARENESS
CONCENTRICITY .005 TIR± 1/16
± .005".xxx
± 1°ANGULAR
0 TO 24"> 24"
ANGULAR± 2°
± .06"± .12" SCALEEST. WEIGHT PROJECT
± .015"± .030"
MACHINING IMPERIAL
FABRICATING IMPERIAL
- UNLESS OTHERWISE SPECIFIED
FABRICATING [METRIC]
> 600 mm0 TO 600 mm
DECIMAL± 3 mm± 1 mm
.xx
.x
CHECKED
MATERIALAPPRV'D
DRAWN
REV
TECHNOLOGY LTD.CANRIG DRILLING
AY11400-2 0
WASHPIPE CPLG TOOL, 3 IN BOREISOMETRIC
WELDING PROCEDURE UNLESS OTHERWISE SPECIFIED - ANSI/AWS D1.1-98 OR CSA W59-M1989 DC 02/07/24- -- -
SEE ALSO DWG#AY11400-1
60 LBS 3/4"=1" -
IF IN DOUBT......PLEASE ASK!
IF IN DOUBT......PLEASE ASK!
SHEET 2 OF 2
1
4
6
1
6
5
5
8
3
Part: AY11679WRENCH TOOL ASSY, WASHPIPE, 3 IN
Drawing ID: AY11679 Rev No: 0
Item Qty Part ID DescriptionUnits
Engineering Bill of Material
Description:
Eng ID: 0
Eng ID
01 1.00 TOOL, WRENCH, WASHPIPE, 3 IN BOREEA DT12546 0
02 2.00 FERRULE, 3/16, OVAL, ALUMINIUMEA M19-3007-01003 1.33 WIRE ROPE, 3/16, 7 x 19, STAINLESSFT M21-2001-010
Printed: 12/30/2003 Page 1 of 1
BYNo. Y/M/D
± .010 IN 5 INCHES± .005 IN 5 INCHES
TOLERANCEREMOVE SHARP CORNERS AND BURRS
± .010 IN 5 INCHESWITHOUT PERMISSION AND RETURNED
CANRIG DRILLING TECHNOLOGY LTD..AND INVENTION ARE RESERVED BYUPON DEMAND. ALL RIGHTS OF DESIGN
REVISION MACHINED SURFACES
PARALLELISMTRUE POSITION
125.005
THAT IT IS NOT TO BE REPRODUCEDFURNISHED WITH THE UNDERSTANDINGTECHNOLOGY LTD.. THIS PRINT ISAND INVENTION OF CANRIG DRILLINGSHOWN THEREON ARE THE PROPERTYTHIS PRINT AND DESIGN AND DETAIL
CASTING
STRAIGHTNESSSQUARENESS
CONCENTRICITY .005 TIR± 1/16
± .005".xxx
± 1°ANGULAR
0 TO 24"> 24"
ANGULAR± 2°
± .06"± .12" SCALEEST. WEIGHT PROJECT
± .015"± .030"
MACHINING IMPERIAL
FABRICATING IMPERIAL
- UNLESS OTHERWISE SPECIFIED
FABRICATING [METRIC]
> 600 mm0 TO 600 mm
DECIMAL± 3 mm± 1 mm
.xx
.x
CHECKED
MATERIALAPPRV'D
DRAWN
REV
TECHNOLOGY LTD.CANRIG DRILLING
AY11679 0
WRENCH TOOL ASSY, 3 IN
WELDING PROCEDURE UNLESS OTHERWISE SPECIFIED - ANSI/AWS D1.1-98 OR CSA W59-M1989 DC 02/09/02- -- -
-
30 LBS 1:1 -
IF IN DOUBT.......PLEASE ASK!
IF IN DOUBT.......PLEASE ASK!
NOTES:
1) ITEMS 02 AND 03 NOT SHOWN. LOOP WIRE THRU HOLEIN HANDLE, THEN CRIMP USING FERRULES. LOOPSHOULD BE APPROX. 5" IN DIAMETER.
02 03
01
MACHINED VERSION
BYNo. Y/M/D
± .010 IN 5 INCHES± .005 IN 5 INCHES
TOLERANCEREMOVE SHARP CORNERS AND BURRS
± .010 IN 5 INCHESWITHOUT PERMISSION AND RETURNED
CANRIG DRILLING TECHNOLOGY LTD..AND INVENTION ARE RESERVED BYUPON DEMAND. ALL RIGHTS OF DESIGN
REVISION MACHINED SURFACES
PARALLELISMTRUE POSITION
125.005
THAT IT IS NOT TO BE REPRODUCEDFURNISHED WITH THE UNDERSTANDINGTECHNOLOGY LTD.. THIS PRINT ISAND INVENTION OF CANRIG DRILLINGSHOWN THEREON ARE THE PROPERTYTHIS PRINT AND DESIGN AND DETAIL
CASTING
STRAIGHTNESSSQUARENESS
CONCENTRICITY .005 TIR± 1/16
± .005".xxx
± 1°ANGULAR
0 TO 24"> 24"
ANGULAR± 2°
± .06"± .12" SCALEEST. WEIGHT PROJECT
± .015"± .030"
MACHINING IMPERIAL
FABRICATING IMPERIAL
- UNLESS OTHERWISE SPECIFIED
FABRICATING [METRIC]
> 600 mm0 TO 600 mm
DECIMAL± 3 mm± 1 mm
.xx
.x
CHECKED
MATERIALAPPRV'D
DRAWN
REV
TECHNOLOGY LTD.CANRIG DRILLING
AY11679 0
WRENCH TOOL ASSY, 3 IN
WELDING PROCEDURE UNLESS OTHERWISE SPECIFIED - ANSI/AWS D1.1-98 OR CSA W59-M1989 DC 02/09/02- -- -
-
30 LBS 1:1 -
IF IN DOUBT.......PLEASE ASK!
IF IN DOUBT.......PLEASE ASK!
01
02 03
NOTES:
1) ITEMS 02 AND 03 NOT SHOWN. LOOP WIRE THRU HOLEIN HANDLE, THEN CRIMP USING FERRULES. LOOPSHOULD BE APPROX. 5" IN DIAMETER.
WELDED VERSION
Part: AY11730WASHPIPE REMOVAL TOOL SET, 3 IN
Drawing ID: NO DRAWING Rev No: 0
Item Qty Part ID DescriptionUnits
Engineering Bill of Material
Description:
Eng ID: 0
Eng ID
01 1.00 WASHPIPE CPLG TOOL ASSY, 3 INEA AY11400 0
02 1.00 WRENCH TOOL ASSY, WASHPIPE, 3 INEA AY11679 0
Printed: 12/30/2003 Page 1 of 1
Revision 03.12 1
WASH PIPE COUPLING & WRENCH TOOL (3” & 4” WP)
1
INTRODUCTION........................................................................................................... 2
DESCRIPTION:............................................................................................................. 2 1) Wash Pipe Coupling Tool:...................................................................................... 2 2) Wash Pipe Wrench Tool ........................................................................................ 3 3) Wash Pipe Retaining Tool...................................................................................... 3
Operating Instructions................................................................................................ 4 Sequence of operation – Removal of wash pipe: ....................................................... 4 Sequence of operation – Installation of wash pipe ..................................................... 5
Canrig Top Drive Drilling System
2 Revision 03.12
INTRODUCTION: To improve the productivity and help eliminate safety hazards associated with the removal of the Wash Pipe nuts, CANRIG has designed a Wash Pipe removal tool that is safe, user friendly and more efficient. The tool consists of three parts, the coupling tool, the wrench tool and the retaining tool. DESCRIPTION:
1) Wash Pipe Coupling Tool: The coupling consists of a split tubular where both pieces are hinged by two pins on one side while the other side has two removable pins to open and close. The coupling has 4 lugs on each end which are designed to fit into the lugs on each of the upper and lower nuts. Each of the nuts has 5 lugs which indicate that only 4 lugs will make contact with the coupling. The coupling will fit between the two nuts as shown below.
Picture shows the 3” Wash Pipe Coupling with Nuts
Wash pipe Coupling & Wrench Tool
Revision 03.12 3
2) Wash Pipe Wrench Tool The Wrench is designed to make-up and breakout the lower nut only. As shown below, the 3” Wash Pipe Wrench has four lugs and an opening that is large enough to fit around the Wash Pipe and then slid down to fit on the lower nut. On the other hand, the 4” Wash Pipe Wrench has 5 lugs, however two of the lugs are hinged to the main wrench to allow it to fit over the Wash Pipe before sliding it down to fit onto the lower nut. Both the 3” and 4” Wash Pipe Wrenches have an arm that will rest against the open window in the Bonnet when breaking out or making up the lower nut.
4” Wash Pipe Wrench 3” Wash Pipe Wrench
3) Wash Pipe Retaining Tool The wash pipe retainer tool (P/N DT12826) fits between the wash pipe and the quill, to prevent the wash pipe from sliding into the quill, once the lower nut is loose.
Wash Pipe Retainer Tool - P/N: DT12826
Canrig Top Drive Drilling System
4 Revision 03.12
Operating Instructions
Sequence of operation – Removal of wash pipe: When attempting to remove an old wash pipe where the packing is worn out, it may very well be that the threads on the lower nut had lost tension. In this case, if you were to use the wash pipe coupling tool first, the lower nut will most likely break out before the upper nut does. Therefore, for the sake of saving time, it maybe more advantageous to tighten the lower nut using the wash pipe wrench prior to using the wash pipe coupling tool. CAUTION: a) The Torque Boost should NEVER be used when tightening the wash
pipe nuts due to the excessive torque that it generates. It maybe used for aligning the nuts lugs only.
b) The top and lower nuts have left hand threads c) Apply a liberal amount of anti-seize to the threads of both nuts prior
to tightening.
1. Install the wrench tool by fitting it around the wash pipe and then sliding it down to fit onto the lower nut.
2. Set the drilling torque limit to ZERO. Next, advance the throttle in FORWARD
direction to approximately 10 o’clock position.
3. To prevent the wrench arm from slamming against the side of the bonnet window, VERY SLOWLY increase the drilling torque to:
3” WP tool 4” WP tool 6000 Ft-lbs 8000 Ft-lbs
Once the proper torque has been applied for approximately 5 seconds, zero the
throttle and the drilling torque, and remove the wrench.
4. Align the top and bottom wash pipe nuts such that the lugs are in synchronization (i.e. will allow the coupling tool to be installed), by rotating the Top Drive with the torque boost Make-up or Break-out).
5. Remove pins from coupling tool to allow the tool to be opened
6. Pending wash pipe nut design you may have to remove the grease zirc before
installing the coupling tool.
7. Install coupling tool between the upper and lower wash pipe nut.
Wash pipe Coupling & Wrench Tool
Revision 03.12 5
8. Close the coupling tool and insert the pins (removed in step 5).
9. For loosening of the upper wash pipe nut (do not fully unscrew it, until the wash pipe retainer tool has been inserted, see step 13), rotate the Top Drive reverse. This is accomplished by first setting the Drill Torque limit to ZERO. Now move the Joystick into the REVERSE position and advance the throttle to select very slow rotation (approx. 10 o’clock position). Next, very slowly increase the Drill Torque limit to the following limits:
3” WP tool 4” WP tool 6000 Ft-lbs 8000 Ft-lbs
Zero the torque limit and throttle, as soon as the nut breaks the connection. Make sure that the top nut is not fully unthreaded, as it will be used to hold the wash pipe in place until step 13.
10. Should the bottom wash pipe nut break before the top nut, remove the coupling
tool and perform steps 1 through 9, however, the make up torque for the lower nut should be increased to 7000 ft-lb and 9000 ft-lb for the 3” and 4” nuts respectively, otherwise proceed to step 11.
11. Remove the coupling tool and install the wrench onto the lower nut.
12. For loosening of the lower wash pipe nut, rotate the Top Drive in a reverse
direction. This is accomplished by first setting the Drill Torque limit to ZERO. Now set the joystick to REVERSE and advance the throttle to select very slow rotation (approx. 10 o’clock position). Next, very slowly increase the Drill Torque limit to:
3” WP tool 4” WP tool 7000 Ft-lbs 9000 Ft-lbs
Zero the throttle, as soon as the nut breaks the connection. Any further rotation can be done by repeating this step again until the lower nut is fully unthreaded.
13. Remove the wrench and install the wash pipe retainer tool (P/N DT12826)
between the wash pipe and the quill, to prevent the wash pipe from sliding into the quill, once the lower nut is loose.
14. Continue to loosen (unthread) the upper nut by hand until is completely free.
Remove the wash pipe assembly.
Sequence of operation – Installation of wash pipe
15. After the wash pipe assembly has been properly assembled, make sure that the threads of both the top and lower nuts have a liberal amount of anti-seize coating. Insert the wash pipe assembly into the Top Drive through the large
Canrig Top Drive Drilling System
6 Revision 03.12
bonnet window and start both nuts (by hand) until at least two full turns of thread are engaged. Note: Both threads are LEFT-HAND.
16. Install the coupling tool (as per steps 4-8).
17. Set the drilling torque limit to ZERO. Next, advance the throttle in FORWARD
direction to approximately 10 o’clock position.
18. To prevent over-torquing, VERY SLOWLY increase the drilling torque in small increments to 1000 ft-lbs until the nuts shoulder up. If 1000 ft-lbs is not enough to make the nuts shoulder up, SLOWLY increase torque limit to 2000 ft-lbs until they do. Once the threads have fully shouldered up, SLOWLY increase the drilling torque as shown below:
3” WP tool 4” WP tool 4500 Ft-lbs 6000 Ft-lbs
Once the proper torque has been applied for approximately 5 seconds, zero the
throttle and the drilling torque, and remove the coupling tool.
19. Check wash pipe seals for any leak. If the seals are still leaking, repeat steps 17 and 18 (above) by slowly increasing torque limit by 500 ft*lbs above previous setting until seals are tight. Do not exceed the following maximum torque values:
3” WP tool 4” WP tool 6000 Ft-lbs 9000 Ft-lbs
If sealing of the wash pipe is not possible with the above maximum torque values, the packing may be defective and needs to be replaced with a new unit.
20. Once a proper seal has been accomplished, remove the coupling tool. This
concludes the installation sequence.