REV. DATE DESCRIPTION BY CKD. BY
WEIGHTPOUNDS
VOLUMECUBIC FEET
FIGURE NUMBER
LOCATIONFI
GU
RE
NU
MBE
R
DIM
ENSI
ON
S AR
E SU
BJEC
T TO
MAN
UFA
CTU
RER
S TO
LER
ANC
E AN
D C
HAN
GE
WIT
HO
UT
NO
TIC
EW
E C
AN A
SSU
ME
NO
RES
PON
SIBI
LITY
FO
R U
SE O
F SU
PER
SED
ED O
R V
OID
DAT
A
DR
AWN
BY:
CH
ECKE
D B
Y:AP
PRO
VED
BY:
DAT
E:SC
ALE:
SIZE A
DR
AWIN
G N
UM
BER
C
3.25 (83)3.25 (83)3.25 (83)3.25 (83)3.25 (83)3.25 (83)
3.18 (81)3.93 (100)4.30 (109)5.25 (133)5.57 (141)6.53 (166)
HYDROTROLSENGINEERED WATER HAMMER ARRESTERS
FUNCTION: Engineered water hammer arresters ("Hydrotrols") employ a permanently sealed cushion of air or gas which absorbsthe energy of water hammer and reduces pressure rise in the piping system to a safe level. Hydrotrol units correctly sized andplaced at specific locations in the water piping system, will control the destructive shock of water hammer.
RECOMMENDED SPECIFICATION FOR HYDROSTATIC SHOCK CONTROLSmith series 5000 "Hydrotrol" all stainless steel shock absorbers shall be installed at all solenoid, remote operated or quick closing valves and at each plumbing fixture or battery of plumbing fixtures. Install on both hot and cold water branch lines in an upright position as close as possible to the valve or valves being served. Sizes and locations as indicated on drawings.
PCN/Fig. No.
500550105020503050405050
P.D.I.Symbol
ABCDEF
Fixture UnitRating1-1112-3233-6061-113114-154155-330
ASIZE
3/4 (19)1 (25)1 (25)1 (25)1 (25)1 (25)
B
Hydrotrols Fig. 5005 to 5050 inclusive have beentested and certified in accordance with the Plumbingand Drainage Institute "Standard P.D.I. WH-201"
Hydrotrols are pre-charged and permanently sealed at the factory.All hydrotrols are constructed entirely of stainless steel.
NOTE: Sizing information on reverse side.
5005 To 5050
5005
To
5050
CM
KG
TD2-
12-8
6N
ON
ES5
005
N
D
1.80 (46)2.13 (54)2.42 (61)3.38 (86)3.57 (91)4.50 (114)
C
B
90º
A
CompressionChamber
Shell
Nipple
Units: A, B, C, & D
D
C
B
CompressionChamber
Shell
Units: E & F
D
90º
A
NOTE: Dimensions shown in parentheses are in millimeters.
NOTE: Stainless steel units are lead-free.
L 01/20/11 Updated Logo JJ TWM 11-2-11 Rev. "B" & "D" Dim., Drawing TBW JMN 10-15-13 Revised Function TBW CL
JAY R.SMITH MFG. CO.®
MEMBER OF MORRIS GROUP INTERNATIONAL™POST OFFICE BOX 3237MONTGOMERY, ALABAMA 36109-0237 (USA)TEL: 334-277-8520 FAX: 334-272-7396 www.jrsmith.com
CUSTOMERDRIVEN
SMITH®
MEMBER OF:
®
ASPE®
SANITARY
EN G IN E E RINGPrevention Rather Than Cure
SINCE 1926