Contact Area : 50μ” Gold
Spec No.
GTD0001-00
Update Date
2015/7/14
Revision
E
UDE P/N:
10G Base-T
LED:L-Green;R-Green
Description: RJ45 1x1 Table Up
To:
Customer P/N:
Through Hole
GTD-1C00VS14
Approved Checked Prepared
Spec No. : GTD0001-00 GTD-1C00VS14
1. MECHANICAL DIMENSION
1.1 Product Dimension
www.ude-corp.com
General Tolerance :X.X :
X.XX :
± 0.38
± 0.20
- 1 -
Spec No. : GTD0001-00 GTD-1C00VS14
1.2 Recommended PCB Layout
Component Side of Board
All dimension tolerance are ±0.05mm unless otherwise specified
www.ude-corp.com- 2 -
Spec No. : GTD0001-00 GTD-1C00VS14
1.3 Panel Cutout
www.ude-corp.com- 3 -
Spec No. : GTD0001-00 GTD-1C00VS14
1.4
- All dimensions follow :
FCC subpart F, 68,500, Figure (C)(2)(i) & (C)(2)(ii) & (C)(3)(i)
IEC 60603-7
- All plugs must be meeting the requirements of plug Go & No-Go gauge.
Gauge follow : FCC subpart F, 68,500, Figure (C)(4)(i) & (C)(5)(i)
- There must be no damage to Housing and Locking Latch.
- There must be no nicks and cuts in cable.
- Durability : 750 cycles generally
www.ude-corp.com
Standard RJ45 Plug Specification
- 4 -
Spec No. : GTD0001-00 GTD-1C00VS14
2. REQUIREMENTS
2.1 Design and Construction
2.2 Material
2.2.1 Terminal Parts ( Terminal:Underplating :50μ" min. Nickel overall )
2.2.1.1 RJ Terminal : PH. Bronze, Thickness=0.30mm
Finish : Contact Area :50μ" Gold
Solder Tail : 120μ" min. Mt.Tin
2.2.1.3 Input Terminal : Brass, Thickness=0.35mm
Finish : 120μ" min. Mt.Tin
2.2.1.4 Module Terminal : Brass, Thickness=0.30mm
Finish : 120μ" min. Tin
2.2.2 Plastic Parts <UL94V-0>
2.2.2.1 Housing : LCP, Black
2.2.2.2 Case : PA6T, Black
2.2.2.3 Spacer : PA6T,Black
2.2.3 Shield Parts
2.2.3.1 Shield : Stainless steel, Thickness=0.20mm, Pre-soldering
www.ude-corp.com- 5 -
Product shall be of design, construction and physical dimensions specified
on applicable.
Spec No. : GTD0001-00 GTD-1C00VS14
2.3 Operating and Storage Temperature
2.4 RJ45 specifications
2.5 Performance and Test Description
2.6 Packaging and Packing
www.ude-corp.com
Operating Temperature :
44N max
Insulation Resistance :
Locking Force of Plug Latch :
Storage Temperature :
Product is designed to meet electrical, mechanical and environmental
performance requirements specified in below table. All tests are performed
at ambient environmental conditions per MIL-STD-1344A and EIA-364
unless otherwise specified.
All parts shall be packaged and packed to protect against physical
damage、corrosion and deterioration during shipment and storage.
2500 cycles
500MΩ min.
Durability :
50N min. @ 60+/-5 sec
- 6 -
Removal force with the latch depressed :
0°C to +70°C
Insertion force with the latch depressed : 22N max
-40°C to +85°C
Spec No. : GTD0001-00 GTD-1C00VS14
3. ELECTRICAL CHARACTERISTICS
3.1 Schematic
www.ude-corp.com
Green
Emitting Color λp (nm) Vf @If=20mA Ir @Vr=5V
- 7 -
565 1.7 ~2.6 V 10μA max.
INPUT RJ45 OUTPUT
C1 TRP1+
C2 TRP1-
C3 TRP2+
C6 TRP2-
C4 TRP3+
C5 TRP3-
C7 TRP4+
C8 TRP4-
2KV 1000pF
Shield
300Ω
75Ω
75Ω
75Ω
1 : 1
1 : 1
1 : 1
1 : 1
TRD1+ R8 TRCT1 R7 TRD1- R9
TRD2+ R2 TRCT2 R1 TRD2- R3
TRD3+ R4 TRCT3 R6 TRD3- R5
TRD4+ R10 TRCT4 R12 TRD4- R11
1 : 1 IET+ R13
IET- R14 IETCT R15
Green
L1
L2
Green
L3
L4
Spec No. : GTD0001-00 GTD-1C00VS14
3.2 Transmitter filter & Receiver filter
Type : Balance low pass 100Ω impedance
Insertion Loss
5MHZ -0.55 dB Max
200MHZ -0.77 dB Max
400MHZ -1.41 dB Max
3.3 Return Loss
100MHz -24 dB Min load 100Ω
200MHz -18 dB Min load 100Ω
300MHz -15 dB Min load 100Ω
400MHz -10 dB Min load 100Ω
500MHz - 8 dB Min load 100Ω
3.4 Reflected CM to Diff Conversion(REF)
50MHZ -30 dB Min
100MHZ -27 dB Min
200MHZ -24 dB Min
300MHZ -22 dB Min
400MHZ -21 dB Min
500MHZ -20 dB Min
www.ude-corp.com- 8 -
Spec No. : GTD0001-00 GTD-1C00VS14
3.5 Reflected Diff to CM Conversion(REF)
1MHZ -48 dB Min
100MHZ -35 dB Min
400MHZ -24 dB Min
500MHZ -24 dB Min
3.6 CM to DM Conversion(REF)
50MHZ -48 dB Min
100MHZ -42 dB Min
200MHZ -36 dB Min
300MHZ -33 dB Min
400MHZ -30 dB Min
500MHZ -28 dB Min
3.7 CM to CM Attenuation
1MHZ -22 dB Min
500MHZ -20 dB Min
800MHZ -20 dB Min
1000MHZ -17 dB Min
3.8 Cross Talk
1 MHz -34 dB Min
350 MHz -23 dB Min
500 MHz -23 dB Min
www.ude-corp.com- 9 -
Spec No. : GTD0001-00 GTD-1C00VS14
3.9 5th channel common mode pick up
Line side D CM to PHY side E diff: 1-400MHz - 7dB Max
( must be between 0dB and -7dB)
3.10 Inductance @ 100KHz, 0.1V 8mA DC BIAS
Input (R8-R9), Input(R2-R3), Input (R4-R5), Input(R10-R11): 160 μH min.
Input (R13-R14): 40 μH min.
3.11 HiPot Test
Input(R8-R9) To Output(C1-C2) : 1500Vac 60s or 2250Vdc 60s
Input(R2-R3) To Output(C3-C6) : 1500Vac 60s or 2250Vdc 60s
Input(R4-R5) To Output(C4-C5) : 1500Vac 60s or 2250Vdc 60s
Input(R10-R11) To Output(C7-C8) : 1500Vac 60s or 2250Vdc 60s
www.ude-corp.com- 10 -
Spec No. : GTD0001-00 GTD-1C00VS14
4. ORDER INFORMATION
G T D - 1 C 00 4
A B D
A. LED Code :
B. Mechanical Code :
C. Schematics Code :
D. Plating Code :
A : 1 :
C : 6 :
B :
D : 2 :
F : 3 :
G : 4 :
www.ude-corp.com
C
VS1
- 11 -
15μ " gold 15μ " gold
30μ " gold
w/ UDE Small logo, w/ T&S Spring
30μ " gold
50μ " gold 50μ " gold
10μ " gold
50μ " min. Nickel overall
120μ " min. Matted Tin
Gold Flash
120μ " min. Bright Tin
Gold Flash
Contact Area
6μ " gold6μ " gold
VS1 : VS1 circuit
Underplating
Solder Tail
L-Green;R-Green. <Refer to Schematic of LED>
Spec No. : GTD0001-00 GTD-1C00VS14
5. IR REFLOW TEMPERATURE PROFILE
www.ude-corp.com- 12 -
Spec No. : GTD0001-00 GTD-1C00VS14
6. Revision History
www.ude-corp.com- 13 -
Issue Date Revision Comments Operator
2013/12/17 A Initial Release . Bin
2014/11/24
2015/7/2 D Update High Frequence SPEC Jeffrey
2014/12/4 C KenUpdate Panel Cutout Drawing
2015/7/14 EChange General Tolerance
from .X :± 0.38;..XX ± 0.25 to .X :± 0.38; ..XX ± 0.20
,product width from 17.78 to 17.53,and update Panel Cutout
Poter
B Update Mechanical Drawing Ken