patterns
WinterWonderlandThis winter, Lammily will
have a blast wearing this
amazing assemble! She
can’t wait to go skiing,
sledding, or just playing in the
snow! Enjoy this simple pattern
with step-by-step instructions.
SIZE: This pattern is custom designed to fit
Lammily dolls.
NOTE: good grasp on sewing, experience with patterns and
sewing terms are needed to complete this design.
This pattern is copyright © Lammily LLC. All Rights Reserved. Copying and/or distributing this pattern is strictly prohibited.
Winter Wonderland patterns designed by Chelly Wood
INTERMEDIATE
Download complete set at www.lammily.com
FREE SAMPLE
This pattern is copyright © Lammily LLC. All Rights Reserved. Copying and/or distributing this pattern is strictly prohibited.
Print out pattern pieces on 8.5” X 11” (letter size) paper. Make sure to print at actual size (100%). Check the 1” reference lines on the pattern pages against a ruler, to ensure you have printed them out at the proper scale.
Separate the pattern pieces, cutting them out on the solid perimeter lines. Patterns that are larger than letter size paper will be printed on multiple pages and need to be assembled.Line up segmented pieces and tape them together.
Lay out pieces on fabric, making sure to line up the pattern pieces parallel to the grainline (arrow on pattern pieces). Pin down pieces and cut them out of fabric.
2
View C
View D
Ski Boots Pattern
This pattern is copyright © Lammily LLC. All Rights Reserved. Copying and/or distributing this pattern is strictly prohibited.
3
1/8” seam allowance
1/8” seam allow
ance
SKI BOOTWRAP-AROUND PIECE
C & DCut 2 of Felt
SKIBOOT
SOLEC & D
Cut 2
1̋
1̋
1/8” seam allowance
SKI BOOTINNER-LEG
PIECE
C & D
Cut 2 of Felt
Ski Boots Instructions
1. Print and cut out Ski Boots Pattern
2. Cut out the pieces as shown, using felt.
3. Place inner-leg pieces on top of ski boot
wrap-around pieces.
4. Sew from the top of the boot to the toe,
where the inner boot and wrap-around
pieces meet at the front of the boot.
5. Press the seam open.
6. Use a washable fabric marker
to mark the tip of the boot’s
sole, where the arrow is
pointing.
7. Begin sewing the sole to the
upper portion of the boot at the
point where you’ve marked. Match the seam
in the upper boot with the marked point at
the tip of the sole.
Here is the
same boot,
looking from
the top:
Attach the
wrap-around
section FIRST
(sew from A
to C). Then,
sew the
shorter
portion (from
A to B).
This pattern is copyright © Lammily LLC. All Rights Reserved. Copying and/or distributing this pattern is strictly prohibited.
4
SKIBOOT
SOLEC & D
Cut 2
9. Stitch three snaps along the edge of the felt
for a primary closure.
We’ll be using
double-folded
1/4˝ (6 mm)
bias tape for
boot’s straps. I
used royal
blue, but any
color will work.
10. Cut six strips of
double-folded bias tape,
3˝ (7.5 cm) long each.
11. Pin the
bias tape to both sides of
the boot first to make sure
you’ve positined it correctly.
12. Use a whip stitch to attach the boot strap
(bias tape) to the side of the boot that
doesn’t have snaps.
This pattern is copyright © Lammily LLC. All Rights Reserved. Copying and/or distributing this pattern is strictly prohibited.
Keep stitching the inner-leg piece to the sole,
even after it starts to overlap the
wrap-around piece.
Now you
should have
two boots
that look like
this:
8. Use a
chopstick or
bamboo
knitting
needle to
invert the
boots.
Now the
wrap-around
piece will appear to wrap towards the front:
Ski Boots Instructions continued
5
When it’s all
snapped up, the
boot looks like this!
13. Attach three
strips of bias
tape to each
boot using
the
whipstitch.
14. Attach very
small snaps
(size 4/0) to
the bias tape
and its corre-
sponding
position on
the boot’s
wrap-around
flap.
Ski Boots Instructions continued
6This pattern is copyright © Lammily LLC. All Rights Reserved. Copying and/or distributing this pattern is strictly prohibited.