ITEM CTF LOCATION NOMINAL +TOL -TOL 1 2 3 1 2 3 UPPER LOWER HIGH LOW 001 8E 1.80 0.10 0.10 Gage block 1.780 1.800 1.780 -0.020 0.000 -0.020 1.787 0% 20% 001 8E 1.80 0.10 0.10 Gage block 1.800 1.830 1.820 0.000 0.030 0.020 1.817 30% 0% 002 5F 148.50 0.75 0.75 Cal 148.620 148.650 148.630 0.120 0.150 0.130 148.633 20% 0% Warpage 003 7E 39.30 0.30 0.40 HG 39.070 39.100 39.060 -0.230 -0.200 -0.240 39.077 0% 60% 004 6E 2.00 0.11 0.11 Cal 1.960 1.950 1.950 -0.040 -0.050 -0.050 1.953 0% 45% 005 5E 3.80 0.12 0.12 HG 3.74 3.75 3.75 -0.060 -0.050 -0.050 3.747 0% 50% 005 5E 3.80 0.12 0.12 HG 3.75 3.78 3.76 -0.050 -0.020 -0.040 3.763 0% 42% 005 5E 3.80 0.12 0.12 HG 3.83 3.85 3.8 0.030 0.050 0.000 3.827 42% 0% 005 5E 3.80 0.12 0.12 HG 3.76 3.78 3.76 -0.040 -0.020 -0.040 3.767 0% 33% 006 5E 94.30 0.20 0.20 Cal 94.21 94.18 94.18 -0.090 -0.120 -0.120 94.190 0% 60% 007 4E 1.80 0.10 0.20 HG 1.840 1.830 1.820 0.040 0.030 0.020 1.830 40% 0% 008 3E 1.50 0.11 0.11 Cal 1.450 1.430 1.440 -0.050 -0.070 -0.060 1.440 0% 64% 009 2F 7.00 0.20 0.10 Cal 6.850 6.880 6.860 -0.150 -0.120 -0.140 6.863 0% 150% Reject Re-measure with PROJ. 010 7C 15.70 0.10 0.10 Cal 15.600 15.600 15.640 -0.100 -0.100 -0.060 15.613 0% 100% 011 Cal ∕ ∕ ∕ Could not pick the feature 012 7D 6.60 0.10 0.10 Cal 6.520 6.500 6.520 -0.080 -0.100 -0.080 6.513 0% 100% 012 7D 6.60 0.10 0.10 Cal 6.500 6.520 6.500 -0.100 -0.080 -0.100 6.507 0% 100% 013 5D 131.10 0.30 0.30 Cal 130.950 130.940 130.970 -0.150 -0.160 -0.130 130.953 0% 53% 014 3D 76.70 0.50 0.50 Cal 76.130 76.150 76.100 -0.570 -0.550 -0.600 76.127 0% 120% Reject Accepted 015 3D 5.20 0.12 0.12 Cal 5.060 5.080 5.060 -0.140 -0.120 -0.140 5.067 0% 117% Reject Modify 016 3C 51.30 0.20 0.20 Cal 51.160 51.230 51.170 -0.140 -0.070 -0.130 51.187 0% 70% 017 2C 35.20 0.28 0.28 HG 35.570 35.600 35.580 0.370 0.400 0.380 35.583 143% 0% Reject Re-measure 018 4B 63.90 0.40 0.40 Cal 63.460 63.400 63.420 -0.440 -0.500 -0.480 63.427 0% 125% Reject Re-measure with PROJ. 019 5A 98.00 0.60 0.60 Cal 98.140 98.090 98.110 0.140 0.090 0.110 98.113 23% 0% FAI OK rate: 73.7% Dimensional Evaluation Data Reporting Sheet 9771. 12-032 PCB support Supplier Remarks Sample Number Customer Disposition Remarks Submission No: f Revision: Material Spec: Drawing Number: Part Description: Deviation from Nominal Up No. / Tool #: INSPECTION RESULTS comments:(P.S: Cal:Caliper; MM:Micrometer; CMMP:CMM Probe;CMMO:CMM Optical; PROJ:2D; HG:Height Gauge; PG:Pin Gauge; VIS:visual;RG:Radius Gauge;TG:Thread Gauge ) Echo 2016/1/2 Simon Inspected By: DRAWING SPECIFICATIONS Inspection Method PP 9771.12-032 INSPECTION ANALYSIS Reviewed By: % Tolerance Acc / Rej Mean Inspection Date: DGQAI-020-F4.01 Page 1 of 1

T1 dimensional evaluation data reporting sheet from hi-precision

Download PDF Report

Upload
huang-simon
View
61
Download
1

Embed Size (px)

Citation preview

Page 1: T1 dimensional evaluation data reporting sheet from hi-precision

ITEM CTF LOCATION NOMINAL +TOL -TOL 1 2 3 1 2 3 UPPER LOWER HIGH LOW

001 8E 1.80 0.10 0.10 Gage block 1.780 1.800 1.780 -0.020 0.000 -0.020 1.787 0% 20%

001 8E 1.80 0.10 0.10 Gage block 1.800 1.830 1.820 0.000 0.030 0.020 1.817 30% 0%

002 5F 148.50 0.75 0.75 Cal 148.620 148.650 148.630 0.120 0.150 0.130 148.633 20% 0% Warpage

003 7E 39.30 0.30 0.40 HG 39.070 39.100 39.060 -0.230 -0.200 -0.240 39.077 0% 60%

004 6E 2.00 0.11 0.11 Cal 1.960 1.950 1.950 -0.040 -0.050 -0.050 1.953 0% 45%

005 5E 3.80 0.12 0.12 HG 3.74 3.75 3.75 -0.060 -0.050 -0.050 3.747 0% 50%

005 5E 3.80 0.12 0.12 HG 3.75 3.78 3.76 -0.050 -0.020 -0.040 3.763 0% 42%

005 5E 3.80 0.12 0.12 HG 3.83 3.85 3.8 0.030 0.050 0.000 3.827 42% 0%

005 5E 3.80 0.12 0.12 HG 3.76 3.78 3.76 -0.040 -0.020 -0.040 3.767 0% 33%

006 5E 94.30 0.20 0.20 Cal 94.21 94.18 94.18 -0.090 -0.120 -0.120 94.190 0% 60%

007 4E 1.80 0.10 0.20 HG 1.840 1.830 1.820 0.040 0.030 0.020 1.830 40% 0%

008 3E 1.50 0.11 0.11 Cal 1.450 1.430 1.440 -0.050 -0.070 -0.060 1.440 0% 64%

009 2F 7.00 0.20 0.10 Cal 6.850 6.880 6.860 -0.150 -0.120 -0.140 6.863 0% 150% Reject Re-measure with PROJ.

010 7C 15.70 0.10 0.10 Cal 15.600 15.600 15.640 -0.100 -0.100 -0.060 15.613 0% 100%

011 Cal ∕ ∕ ∕ Could not pick the feature

012 7D 6.60 0.10 0.10 Cal 6.520 6.500 6.520 -0.080 -0.100 -0.080 6.513 0% 100%

012 7D 6.60 0.10 0.10 Cal 6.500 6.520 6.500 -0.100 -0.080 -0.100 6.507 0% 100%

013 5D 131.10 0.30 0.30 Cal 130.950 130.940 130.970 -0.150 -0.160 -0.130 130.953 0% 53%

014 3D 76.70 0.50 0.50 Cal 76.130 76.150 76.100 -0.570 -0.550 -0.600 76.127 0% 120% Reject Accepted

015 3D 5.20 0.12 0.12 Cal 5.060 5.080 5.060 -0.140 -0.120 -0.140 5.067 0% 117% Reject Modify

016 3C 51.30 0.20 0.20 Cal 51.160 51.230 51.170 -0.140 -0.070 -0.130 51.187 0% 70%

017 2C 35.20 0.28 0.28 HG 35.570 35.600 35.580 0.370 0.400 0.380 35.583 143% 0% Reject Re-measure

018 4B 63.90 0.40 0.40 Cal 63.460 63.400 63.420 -0.440 -0.500 -0.480 63.427 0% 125% Reject Re-measure with PROJ.

019 5A 98.00 0.60 0.60 Cal 98.140 98.090 98.110 0.140 0.090 0.110 98.113 23% 0%

FAI OK rate: 73.7%

Dimensional Evaluation Data Reporting Sheet

9771. 12-032

PCB support

Supplier RemarksSample Number

Customer Disposition

Remarks

Submission No:

fRevision: Material Spec:

Drawing Number:

Part Description:

Deviation from Nominal

Up No. / Tool #:

INSPECTION RESULTS

comments:(P.S: Cal:Caliper; MM:Micrometer; CMMP:CMM Probe;CMMO:CMM Optical; PROJ:2D; HG:Height Gauge; PG:Pin Gauge; VIS:visual;RG:Radius Gauge;TG:Thread Gauge )

Echo

2016/1/2

Simon

Inspected By:

DRAWING SPECIFICATIONS Inspection

Method

9771.12-032

INSPECTION ANALYSIS

Reviewed By:

% Tolerance Acc / RejMean

Inspection Date:

DGQAI-020-F4.01 Page 1 of 1