1

1

SURGICAL MOTOR SYSTEM,DEVELOPED FOR MULTIPLE INDICATIONS

As part of our new generation Surgical Motor Systemsthe HighSurg 30 was developed for a wide variety ofapplications, such as ENT Surgery, Neurosurgery Maxillofacial Surgery as well as Orthopedics and Ar-throscopy. The conciliatory treatment of patients by minimally invasive surgical technics in conjunction with endoscopy was the central part in the development of the new HighSurg 30.

A sophisticated, micro processor controlled motor man-agement is responsible for a silky-smooth,low vibrationrunning of any handpiece used. Precise and save cuts, as we know them only from high priced Motor Systemsare now possible with this further developed Shaver System with a continuous mode as well as an oscillat-ing mode. The cooling of the instruments is maintainedby the built-in, fine tunable peristaltic pump.

A broad range of newly developed Shaver Blades are available for all situations one might think of and form awell matched unified whole with the new HighSurg 30. The user-friendly conception of operation together withthe big display, which holds all information ready at a glance, as well as the real-time display of the revolutionper minute and the torque graph, provide safety andconfidence in every situation.

Type: Electronic Motor 21Weight (without cable): 280gI-max .: 8AInput Voltage: 35VMotor speed: up to 50,000/80,000* rpmMax. motor torque: 6 NcmCoupling Electronic Mortor: after INTRA EN3964Cable length: 3m* 80,000 rpm motor available, Art. No. 2098

Electronic Motor 21 Arcticle No.Brushless motor with up to 2099/2098*50,000 rpm, sterilisable andautoclavable, with a 3 meterpower cord.

To keep your focus on the job we equipped the High-Surg 30 with two motor connections, which spares the rechucking of Handpieces. With the included pedal you control the pump, the programmes and the motor. Withthe tread-plate the revolutions per minute of the motor and the activation of the pump are directed. The High-Surg 30 is eminently suitable for all areas of Micro

Surgery and is convincing by the ideal combination of carefully aligned technologies and materials.

2

GOOD REASONS FOR THE HIGHSURG 30

The HighSurg 30 holds many useful qualities ready. Be it the possibility of calibration of the handpieces, the adjustment of many functions after personal needs or the sophisticated motor management. Here come further good reasons to aknowledg:

1.Ergonomic housingLight and compact housing, simple to clean surfaces.

3.Low noise pump drive Inner, capsuled pump drive of low noise level.

2.Large displayVisibility in all work steps with a large, clearly arranged display with high contrast.

4.Engagement of tube set Good visible tube set holding fixture, integrated in the cover of the pump compartment.

6.New motor managementFine tuned motor management for best precision and operation comfort.

5.Dual motor principleThe dual motor principle is unique in this class. It saves cumbersome reconfiguration of the Handpieces. Your focus stays with the patient.

15 Handpieces possibleSuitable for all fields of Microsurgery.

3

SURGICAL STANDARD HANDPIECES/STRAIGHT AND ANGLED

Angled standard handpiece with a length of 125 mm and 1:1 transmission, with spray nozzle and quick lock for in-struments with a length of 70 mm and a shaft diameter of 2.35 mm

Angled standard handpiece with a length of 145 mm and 1:1 transmission,with spray nozzle and Quick lock for in-struments with alength of 95 mm and a shaft diameterof 2.35 mm

Angled standard handpiece with a length of 175 mm and 1:1 transmission, with spray nozzle and Quick lock for in-struments with alength of 125 mm and a shaft diameterof 2.35 mm

1:1 Contra Angle with INTRA EN3964 coupling for drillswith a shaft diameter of 2.35 mm (dental shaft).

1:3 Handpiece, Length 135 mm, for up to 140,000 rpm; spray nozzle; quick release lock; for instruments with alength of 70 – 95 mm and a diameter of 2.35 mm

General surgery handpiece with a length of 90 mm and 1:1 transmission, with spray nozzle and Quick lock for in-struments with a length from 44 mm and a shaft diameterof 2.35 mm

General surgery handpiece with a length of 105 mm and 1:1 transmission, with spray nozzle and Quick lock for in-struments with a length of 70 mm and a shaft diameterof 2.35 mm

General surgery handpiece with a length of 125 mm and 1:1 transmission, with spray nozzle and Quick lock for in-struments with a length of 95 mm and a shaft diameterof 2.35 mm

General surgery handpiece with a length of 155 mm and 1:1 transmission, with spray nozzle and Quick lock for in-struments with a length of 125 mm and a shaft diameterof 2.35 mm

Article No.1960

Article No.1961

Article No.1962

Article No.5050

Article No.1063

Article No.1710

Article No.1950

Article No.1951

Article No.1952

4

CRANIAL-INSTRUMENTS

Perforator

Craniotome

Type: Perforator, Article No. 1924Weight: 390 gSpeed range: from 200 up to 1000 rpmPermissable manimal torque: 55 NcmCoupling: after INTRA EN3964

Type: Craniotome, Article No. 1925, 1926, 1927Weight: 130 gSpeed range: from 1000 up to 50,000 rpmPermissable manimal torque: 6 NcmCoupling: after INTRA EN3964

Duraprotector available in 3 sizes:

Large ArticleNo. 1927

Medium ArticleNo. 1926

Pedriatric ArticleNo. 1926

Unicersally appplicable cranial instrumentThe Perforator is used in a right angle to the cranial arc tangent to make sure to take advantage of the full effect of the automatic locking system at drilling.

5

SURGICAL MICRO SAWS

Micro Compass Saw MSS 5000

Micro Oscillating Saw OMS 5000

Osseoscalpel, Sagittal Saw MOS 5000

Article No. OMS 5000 Oscillating micro5090 saw with INTRA EN3964 coupling, removable irrigation tube, recommended speed 15,000 rpm.

Article No. MOS 5000 Sagittal Saw5110 with INTRA EN3964 coupling, removable irrigation tube, rec- ommended speed 15,000 rpm.

Article No.5041 11mm5042 14mm5043 18mm5044 22mm5045 26mm5105 17 mm, rounded5106 21 mm, rounded

Article No. Cutting depth Shaft length5100 6,3 mm 33 mm5099 6,3 mm 45 mm

5093 13,3 mm 33 mm5096 13,3 mm 45 mm

5094 13,3 mm 33 mm5097 13,3 mm 45 mm

5095 13,3 mm 33 mm5098 13,3 mm 45 mm

Article No. 5115 5116 5114 5117 5118 5119Cutting depth 4 mm 6 mm 6 mm 6 mm 10 mm 12 mmlength 12 mm 12 mm 12 mm 17 mm 17 mm 29 mm

Spare blades of 0.4 mm thickness, in packing units of 6 pieces.

Saw blades of 0.4 mm thickness, in packing units of 1 piece.

Saw blades of 0.4 mm thickness, in packing units of 6 pieces.

Set of 1 eachArticle No.5049

Article No. 5120nou

Article No. MSS 5000 Micro-jigsaw with5040 INTRA EN3964 coupling, re- movable irrigation tube, recom- mended speed 15,000 rpm.

Article No. Rasp tool, hardened steel,5046 Packing unit of 1 piece.

45

33

6

ORTHOPEDIC HANDPIECES

Kirschner Handpiece

Jacobs straight Handpiece with three-jaw chuck system

The Kirschner Wires used for temporary and permanent fixation of bones and implants are available in different lengthsand diameters. They’re also available with a threaded portion in the middle. The simplicity of changing wires address the surgeons needs. With the motor system that best suites your needs the process of setting the wires with the Kirschnerhandpiece gets done easier with an accurate result that gives you confidence andsafety.

Art.No. Label Ø TL WL

260201 Spiral drill 1.1 45.0 22.0

260202 Spiral drill 1.4 86.0 30.0

260203 Spiral drill 1.5 70.0 22.0

260204 Spiral drill 2.0 88.0 50.0

260205 Spiral drill 2.0 101.0 50.0

260206 Spiral drill 2.0 109.0 17.0

260207 Spiral drill 2.0 109.0 50.0

260208 Spiral drill 2.5 108.0 23.0

260209 Spiral drill 2.5 108.0 50.0

260210 Spiral drill 2.7 111.0 50.0

260211 Spiral drill 3.0 146.0 50.0

260212 Spiral drill 3.2 120.0 50.0

260213 Spiral drill 3.2 146.0 50.0

260214 Spiral drill 3.5 120.0 50.0

260215 Spiral drill 3.5 146.0 50.0

260216 Spiral drill 4.0 156.0 50.0

260218 Spiral drill 4.5 156.0 50.0

260219 Spiral drill 4.5 180.0 50.0

260220 Spiral drill 5.0 156.0 50.0

260221 Spiral drill 5.0 180.0 50.0

260222 Spiral drill 6.5 130.0 50.0

260404 Spiral drill 1.5 44.5 27.5

Art. No. Kirschner Contra angle with INTRA EN3964 coupling, 90 mm length,5160 16:1 transmission, 2500 rpm, for surgical wires of 0.8 – 1.5 mm in diameter.

Surgical WiresArt. No. 5013 5014 5023 2015 5016 5017 5018Length 70mm 70mm 150mm 150mm 150mm 150mm 150mmØ mm 0.8 1.0 0.6 0.8 1.0 1.2 1.5Surgical Wires are available in a box of 10.

Type: Jacobs drill HandpieceWeight: 560 gSpeed range: 200 up to 2600 rpmtorque: 60 NcmCoupling: after INTRA EN3964

7

SPINAL SURGERY

Angled Handplece

Article No. Endoscopic angled Handpiece for spinal1910 burr with a length of 110 mm and 1:1 transmission, with quick lock and a chuck of 2.35 mm.

Support Sleeves

Article No. Reusable Support Sleeve without1914 protector. For working channel 4.1 mm

Article No. Reusable Support Sleeve with distal protector. For working channel 4.1 mm

Article No. Reusable Support Sleeve without1916 protector. For working channel 3.7 mm

Article No. Reusable Support Sleeve with1917 distal protector. For working channel 3.7 mm

Burrs

Article No. Spinal burr with a head diameter of 3 mm 1911 and a shaft diameter of 2.35 mm and a total length of 355 mm. Available in 3 pieces per packing unit, without support sleeve.

Article No. Spinal Burr diamond with a head diameter 1912 of 3 mm and a shaft diameter of 2.35 mm and a total length of 355 mm. Available in 3 pieces per packing unit, without support sleeve.

Article No. Spinal Burr diamond with a head diameter 1913 of 4 mm and a shaft diameter of 2.35 mm and a total length of 355 mm. Available in 3 pieces per packing unit, without support sleeve.

8