MATERIAL

- Cardboard.

- A bulb holder.

- A light bulb.

- A flat battery.

- Flex.

- A okume plank.

- Wood strips.

- Roll to laminate.

- Clips.

- Isolating tape.

- Nails.

- Glue (white).

TOOLS

- Screw driver (star shape).

- Drills.

- Markers.

- Scissors.

- Ruler.

I DON’T

KNOW.

GO AND

ASK JOSU.

MAIDER, WHAT

IS THIS TOOL?

IT’S VERY

STRANGE.

NO, I

KNOW.

THAT TOOL

IS A DRILL.

PROCEDURE

1. Make a wooden base using 4 wood strips. Make a square with the strips

and stick them using white glue.

2. Cover the wooden base with a okume plank. Stick it on top.

3. Draw and colour your area’s map and later cut it.

4.

OK, MADDI.

I’LL PUT ONLY

A LITTLE.

GLUE.

IGOR, BE

CAREFUL WITH

THE GLUE. ONLY

A LITTLE IS

ENOUGH.

I AM GOING

TO MAKE A

FANTASTIC

CONNECTOR.

I CAN’T STOP.

4. You will need a big cardboard. Cut two pieces, as big as the okume plank, in

order to cover the wooden base.

5. Stick the map on the left of the top cardboard. Write the vocabulary you

will use in your game on the right (rivers, mountains...). Later, laminate the

cardboards and stick the top one.

BLA, BLA,

BLA…WHAT A

HEADACHE!

I WISH I WAS

AT HOME XABIER, BE

CAREFUL

WITH THE

LAMINATING

TAPE. IT IS

VERY STICKY.

AITOR, BE

CAREFUL

WITH THE

SCISSORS OR

YOU WILL

CUT YOUR

FINGER.

6. Drive in the nails in each point, drills are very useful now. Number the

nails at the back, give a number to each mountain and give the same

number to the corresponding village.

I HAVE A TERRIBLE PROBLEM THE ISOLATING TAPE IS ESTIC IN MY HANDS.

IS NO PROBLEM I CAN CUT.

7. Now the most difficult task: cut some pieces of flex, cut about 2 cm of

plastic from each end of the pieces of flex and twist the little wires.

Make a small hook at the ends of the flex. Then hook all the numbers.

Number 1 in the village goes with mountain number 1. Number 2 in the .......

8. Drill a hole for the lampholder between the map and the list of mountains

and find an appropriate place for the battery, fix it to the plank using

isolating tape.

UUUUFFFF! I CAN’T

FINISH THE HOLE. I

NEED A TXISTORRA

TALO.

THIS IS VERY

DIFFICULT!

TEACHER, I

NEED HELP.

AAAHHH!

THIS GROUP

IS A

DISASTER.

9. Cut three longer pieces of flex, cut about 2 cm of plastic from each end

and twist the wires. Then make a small hook at the ends of the flex and

hook two of the pieces of flex around the holes of the bulb holder. Hook

the end of one piece of flex onto the positive pole of the battery and tie

it round the other piece of flex goes out with a clip. Hook the third piece

of flex onto the negative pole and tie it round, hook the other end to a

clip, this end goes out too.

10.

MAREN, I NEED YOUR

HELP. WHERE GOES

THE BATTERY? I DON’T

KNOW!

LOOK ALEJANDRA,

THIS IS A

FANTASTIC PLACE

FOR THE BATTERY.

HERE, OK!

11. The connector is nearly ready to play but first you have to cover the back

with a laminated cardboard.

I HAVE A TERRIBLE PROBLEM WITH THE ISOLATING TAPE. WHAT A MESS! IKER HELP ME!

NO PROBLEM, I WILL HELP YOU BUT DON`T MOVE OR I WILL CUT YOUR FINGER.

NOW THE CONNECTOR IS READY TO PLAY MATCH

THE VILLAGES AND THE MOUNTAINS AND IF YOU

ARE RIGHT YOU WILL SEE THE LIGHT.

GOOD LUCK!!!

HURRAY! OUR

FANTASTIC

CONNECTOR IS

READY TO PLAY.

JOKIN, DO YOU

WANT TO PLAY? YES, LET’S PLAY

TOGETHER.

COME ON ENDIKA,

THIS IS GREAT FUN!

LOOK, THE LIGHT!

I DON’T

WANT TO

PLAY NOW.

I’M HUNGRY.

I WANT A

SANDWICH