View
3
Download
0
Category
Preview:
Citation preview
HyperFlow
HyperFlowCOMPACT
®
HyperFlow® Technology
• HyperFlow® changes the way all future hydraulic lifts will be constructed
• HyperFlow® is the basis, for even more safety, due to simpler construction with fewer
parts leading to a longer life of the lift
• HyperFlow® is green, because it uses fewer resources
• A construction using HyperFlow® reduces the necessary raw material by up to 30%
• HyperFlow® protects not only the environment but also the purse
• Why ?
Because thanks to HyperFlow® NUSSBAUM can use fewer parts on the lifts providing an
almost wear free operation
• HyperFlow® is exclusive only by NUSSBAUM
DEVELOPED AND PATENTED BY NUSSBAUMMADE IN GERMANY
3
Automotive L i f tsfor passenger cars and transporters
SMART LIFT .................................................................. 4
POWER LIFT HL K .......................................................... 8
POWER LIFT HL ........................................................... 10
POWER LIFT HL SST & HDL SST .................................... 14
Accessories for SMART LIFT & POWER LIFT.................... 18
COMBI LIFT ................................................................ 20
UNI LIFT NT ................................................................ 24
UNI LIFT – Wheel alignment ........................................ 26
UNI LIFT – Testing ....................................................... 27
UNI LIFT 6000 & 8000 ................................................. 28
Accessories for COMBI LIFT & UNI LIFT ......................... 29
JUMBO LIFT ............................................................... 32
SPRINTER ................................................................... 36
TOP LIFT .................................................................... 40
TOP LIFT with lifting arms ........................................... 42
TOP LIFT with lifting platforms .................................... 43
TOP LIFT with runways ................................................ 44
We replace your old piston lifts ................................... 46
Automotive L i f ts for passenger cars & transporters
L i f ts for passenger cars & transporters
Nylatron-nut: 5 years warranty
Resistant Poly-V belt
MINI MAX lifting arms easy and convenient to lift off-road vehicles and for cars with pressed side skirts
SMART LIFT 2.30 SL – lift for vehicles up to VW T5 with short wheelbase
Vehicles’s door can be opened completely(2.30 SL DT)
Telescopic lifting arms and very low lifting point
SMART L IFTSPINDLE 2-POST LIFTS
SMART L IFT – THE RIGHT SOLUTION FOR ANY WORKSHOP
LIFTS FOR PASSENGER CARS AND TRANSPORTERS – FOR ALL TYPES OF
WORKS ARROUND THE CAR
SMART LIFT 2.30 SL – lifting capacity of 3.000kg,
available in versions: DT and MM
SMART LIFT 2.35 SL – lifting capacity of 3.500kg,
available in versions: DT, MM and SC
SMART LIFT 2.40 SL – with reinforced steel and extended lifting arms for
lifting vehicles up to Mercedes Sprinter with center wheelbase at the alter-
native pick-up points. With a lifting capacity of 4.000kg and UNIVERSAL
carrying arms.
SMART L IFT – THE PROVED TECHNOLOGY
The robust contruction of SMART LIFT as well as its fully developed tech-
nique are the results of more than 10.000 units produced per year and more
than 30 years experience in the manufacturing of lifts.
LONG LIFE- C YCLE
• low wear Nylatron-nut guarantees a quiet operation
• 5 years warranty on spindle and spindle-nut
• two motors integrated into columns
• resistant Poly-V belt – a guarantee for almost wearfree
• complete quality control at all stages
OPTION: ENERGY SET
• electricity and compressed air at the working place
• 230V plug and air connection are integrated in the column
5
www.nussbaum-group.de/smartlift
SMART L IFT – THE RIGHT SOLUTION FOR ANY WORKSHOP
3.000kg | 3.500kg | 4.000kg
SMART LIFT 2.30 SL DT – short lifting arm with 2-times telescopic provides more adjusta-ble range and simplifies lifting of shorter and wider vehicles
SMART LIFT 2.40 SL – lift for passenger cars and transporters, for universal application
Automatic locking of the arms
FLEXIBLE SET UP HEIGHT AND WIDTH
no ground connection between columns
Flexible top connection – adjustable height of top connection without static function
ASYMMETRIC LIFTING ARMS AND CARRIAGE FOR OPTIMAL DOOR CLEARANCE
• lifting wide range of vehicles
• automatic arm adjustment
• lowest pick-up point from 75mm
• short lifting arms with swivelling 180°
• maximum door clearance thanks to the corner position of the carriage
DOUBLE TELESCOPIC LIFTING ARM (DT)
The short lifting arm is 2-times telescopic, providing a large adjustable range and
therefore enabling to lift short and wide vehicles.
Extremely low construction of the carrying arms make this lift ideal for sports cars with
very low clearance.
MINI-MAX LIFTING ARM (MM)
Adapter for low clearance vehicles as well as for deep-drawn side skirt and off-road
vehicles. Adjustable with an enormous range of 75–185mm. Quick vertical multilevel ad-
justment with the foot.
A
BD
E
J
F
G
H
L i f ts for passenger cars & transporters
Foundation
Technical drawings for SMART L IFT
HYMAX S 3000 - 4000
Foundation
7
www.nussbaum-group.de/smartlift
Technical drawings for SMART L IFT
HYMAX S 3000 - 4000
SMART LIFT 2.30 SL 2.35 SL / 2.40 SL
TO BE PREPARED BY CUSTOMER
Foundation min. (mm) 200 200
Concrete quality min. (normal reinforcement) C20/25 C20/25
Bolts (pcs) 12 16
Type of bolt (depends on foundation, see manual)
Hilti-V-5.8, M12 Hilti-V-5.8, M12
Power supply (V / Hz / Amp.) 400 / 50 / 16 400 / 50 / 16
Time-lag fuse (mm²) 5 x 2,5 5 x 2,5
Air supply for energy set optional optional
Unloading (fork lift) required required
Technical data
SMART LIFT 2.30 SL 2.35 SL 2.40 SL
Lifting capacity (kg) 3000 3500 4000
Lifting/ lowering time approx. (sec) 40 / 40 46 / 40 46 / 40
Lifting height (mm) 1983 2010 2060Lowest pick-up point (mm) Version: SCVersion: MINI-MAX
D 95–140–
75–185
95–14082–12275-185
115–190–
75–185
Total height column (mm) Top connection (mm)
JA
28873716–4167
28903715–4115
28903685–4170
Total width (mm) Version: MINI-MAX
H 31003300
32303350
33503350
Drive-through width (mm) Version: MINI-MAX
E 23502504
24002400
25142514
Distance between columns (mm) Version: MINI-MAX
B 24602560
27702650
27702770
Arm extraction long (mm) Version: SCVersion: MINI-MAX
F 940–1495–
1000–1480
940–1495840–13801000-1480
1130–1840–
1130–1840
Arm extraction short (mm) Version: SCVersion: MINI-MAX
G 480–870–
600–980
570–1160590–865600-1000
570–1160–
635–1065
Motor (kW) 2 x 1,5 2 x 1,5 2 x 1,5
Power supply (V/Hz) 400 / 50 400 / 50 400 / 50
Automotive L i f ts for passenger cars & transporters
L i f ts for passenger cars & transporters
POWER L IFT HL 2.30 KHYDR AULIC T WO -POST L IFTS
POWER LIFT HL 2 .30 K – HYDR AULIC AT ALL EVENTS
FAST L IFT ING AND LOWERING TIMES
FUNC TION AND SAFET Y
• Combination of the single master / slave and HyperFlow
technology
• Equipped with 1 hydraulic cylinder in each column
• Safety is guaranteed through an integrated mechanical safety
ratchet
NEW
Automatic locking of lifting arm with finer gearing, manual releasing possible
NO FLOOR CONNECTION BETWEEN COLUMNS
POWER LIFT HL 2.30 K 2-post hydraulic lift with mechani-
cal latch and HyperFlow. Ideal for vehicles and vans up to
3000 kg.
FAST. FUNCTIONAL. RELIABLE.
HANGING HYDR AULIC C YLINDERS
• almost wear-free
• require less hydraulic oil
Telescopic asymmetric lifting arm Optimal door clearance – arrangement of lifting arms is always asymmetric
9
www.nussbaum-group.de/hlnt
HyperFlow
HyperFlowCOMPACT
®
HyperFlow TECHNOLOGY
• Automatic synchronization during operation.
• Automatic purging of the hydraulic system
during operation
3.000KG
POWER LIFT HL 2.30 K
Lifting capacity (kg) 3000
Lifting/ lowering time approx. (sec) 19 / 15
Lifting height (mm) 1990
Lowest lifting point (mm) 95–140
Clearance height (mm) 3967
Total height (mm) 4017
Total width (mm) 3100
Recommended installation width (mm) 3100
Drive-through width (mm) 2395
Distance between column (mm) 2630
Arm extraction long (mm) 945–1493
Arm extraction short (mm) 595–800
Power supply (V/Hz/A) 400/50/16
Motor (kW) 3
TECHNICAL DATA
TO BE PROVIDED BY CUSTOMER
POWER LIFT HL 2.30 K
Foundation min. (mm) 200
Concrete quality min. (normal reinforcement)
C20/25
Bolts (pcs) 12
Type of bolt (depends on foundation, see manual)
Hilti-V-5.8, M12
Unloading (fork lift) required
Picture: column cover as
optional accessory
Telescopic lifting arms with minimum of lowest pick-up point
Automotive L i f ts for passenger cars & transporters
L i f ts for passenger cars & transporters
FUNC TION AND SAFET Y: NT TECHNOLOGY
• Crossed-cylinder master – slave system pro vides a level lifting
and lowering without the need for synchronization cables
• The load is secured at any working height without a mechanical
ratchet
• The all-hydraulic system requires no elec trical or pneumatic
components
• No crossbeam between the columns
• self-purging hydraulic system ensures an easy and safe installati-
on
• synchroniziation is made everytime at the top end position
• The integrated hydraulic oil-submerged motor ensures a quiet
operation
MINI MAX lifting arms – easy and convenient to lift lowered vehicles and for cars with pressed side skirts
POWER L IFT HL NTHYDR AULIC T WO -POST L IFTS
POWER LIFT HL NT – THE PROFESSIONAL SOLUTION FOR ANY WORKSHOP
POWER LIFT HL 2.30 NT – lift for passenger car up to transporter e.g. VW T5 with short wheelbase
Optimum door clearance with asymmetric lifting arm
Automatic locking of lifting arm with finer gearing, manual releasing possible
Scheme of NT-Technology
ACCESSORIES:
• energy set 230V power socket and air supply, integrated in the
column
• hight extensions
• diverse height adapters
FASTEST L IFT ING AND LOWERING
The double master slave system enables fast lifting and lowering
times, 20 and 14 sec respectively.
Low electricity consumption with one motor and no need of po-
wer supply when lowering.
NT TECHNOLOGY
Double hydraulic system replaces mechanical synchronization,
therefore no need of safety ratchet. The lift offers more operati-
on safety and is nearly wear-free.
Double cylinders pull loads from both sides constant and safe.
11
www.nussbaum-group.de/hlnt
HyperFlow
HyperFlowCOMPACT
®
HyperFlow TECHNOLOGY
3.000KG | 3 .500KG | 4 .000KG | 5 .000KG
Short lifting arm with 2-times telescopic arms (DT) provide more adjustable range and simplifies lifting of shorter and wider vehicles
POWER LIFT HL 2.40 NT – Lift for passenger cars and transporter,s for universal application
ADJUSTABLE TOP CONNEC TION
Top connection is adjustable in height and width. Minimum
space is required with an optimal drive-through width. Height
extension including hydraulic hoses in 100mm steps increase
clear heigt from 4104 to 4904mm.
• Automatic synchronization during operation.
• Automatic purging of the hydraulic system during operation.
DOUBLE TELESCOPIC LIFTING ARMS (DT)
Short lifting arm with double telescopic provides a large adjustable range and therefore
enables to lift short and width vehicles.
MINI-MAX LIFTING ARM (MM)
Adapter for low clearance vehicles as well as for deep-drawn side skirt and off-road
vehicles. Adjustable with an enormous range of 75–185mm. Quick vertical multilevel adjust-
ment with the foot.
DOUBLE-JOINTED ARMS (DG)
Symmetric carrying arms of the 5 tons lift. Unique build with 2 joints enable the lifting of
heavy and wide vehicles, small cars and vans like the VW T5 with long wheelbase.
MB & BMW with telescopic arms and recommended installation width. Colors and coating
according to OEM specs. Specific scope of supply. Versions: 3500, 4000 and 5000.
SEVERAL VERSIONS FOR ALL NEEDS
HYMA X PH 3000 – lifting capacity of 3.000kg,
available in versions: DT and MM
HYMAX PH 3500 – lifting capacity of 3.500kg,
available in versions: DT, MM, SC and MB, BMW
HYMA X PH 4000 – lifting capacity of 4.000kg and UNIVERSAL carrying arms
HYMA X PH 5000 – lifting capacity of 5.000kg and symetric double jointed (DG) carrying arms
A
D
K
J
H
E
B
F
G
A
D
K
J
H
E
BF
G
Automotive L i f ts for passenger cars & transporters
L i f ts for passenger cars & transporters
Technical drawings for
POWER L IFT HL 2.30–2.50 NT
13
www.nussbaum-group.de/hlnt
POWER LIFT HL 2.30 NT HL 2.35 NT/2.40 NT HL 2.50 NT
Additional scope of delivery ONLY for Mercedes Benz approved HDL 6500 SST DG MB
Document holder on column | Magnetic basket for wheel nuts | Height adaptersfor Sprinter and for G model with and without running-board | Integrated
CE Stop with acoustic warning signal
TO BE PREPARED BY CUSTOMER
Foundation min. (mm) 200 200 200
Concrete quality min. (normal reinforcement)
C20/25 C20/25 C20/25
Bolts (pcs) 12 16 16Type of bolt (depends on foundation, see manual)
Hilti-V-5.8, M12 Hilti-V-5.8, M12 Hilti-V-5.8, M16
Air supply for energy set optional optional inkl.
Unloading (fork lift) required required required
Hydraulic oil HLP ISO 32, approx. 10 liter HLP ISO 32, approx. 10 liter HLP ISO 32, approx. 10 liter
POWER LIFT HL 2.30 NT HL 2.35 NT HL 2.40 NT HL 2.50 NT
Lifting capacity (kg) 3000 3500 4000 5000
Lifting/ lowering time approx. (sec) 20 / 14 26 / 14 26 / 14 31 / 15
Lifting height (mm) K 1995 1995 2050 2020
Lowest lifting point (mm)Version: MINI-MAXVersion: UniversalVersion: MBVersion: SC
D 95–14075–185
–––
95–14075-185
–95-14082-122
95–14075–185115–19095–140
–
115–190––––
Total height column (mm) J 4022 4040 4027 3962
Total height with riser pipe (mm) A 4104–4904 4109–4909 4109–4909 4109–4865
Total width (mm) Version: MINI-MAXVersion: BMWVersion: MB
H 3100–33003100–3350
––
3230–3350335032303230
3350––
3350
3750––
3750
Recommended width (mm)Version: MINI-MAXVersion: BMWVersion: MB
31003100
––
3230335032303230
3350––
3350
3750––
3750
Drive-through width (mm) Version: MINI-MAXVersion: BMWVersion: MB
E 2313–25132504
––
2400–2520–
24002400
2522––
2522
2790––
2790
Column distance (mm) Version: MINI-MAX
B 2560–27602760
26462766
2766–
3090–
Arm extraction long (mm) Version: MINI-MAXVersion: UniversalVersion: BMWVersion: MBVersion: SC
F940–1495
1000–1480––––
940–14951000-480
–505–823505–823840–1380
1130–1840–
570–1160–
1130–1840–
778–1213–––
0–1825–
Arm extraction short (mm) Version: MINI-MAXVersion: BMWVersion: MBVersion: SC
G 480–870600–980
–––
570–1160600-900505–823505–823590–865
600–900635–1065
–600–900
–
778–1213––
0–1825–
Power supply (V/Hz/A) 400/50/16 400/50/16 400/50/16 400/50/16
TO BE PREPARED BY CUSTOMER
Technical data
Automotive L i f ts for passenger cars & transporters
L i f ts for passenger cars & transporters
POWER L IFT HL SST & HDL SST
Hydraulic l i f t with elec tronic synchronization ensures safety in any l if t ing
height without safety ratchet
SST – SAFETY STAR TECHNOLOGY
• patented safety system
• interaction with a micro-controller and proportional valves, SST guarantees perfect synchronization
• Electronical measuring system at ball bearing circulation controls the synchronization of lifting
unit exactly to tenth of a millimeter
DOUBLE-JOINTED ARMS
Unique construction with double-jointed per lifting arm for
• reaching 100% of pick-up points
• easy lifting of passenger cars through 90° of lifting arms positioning
• required pick-up points from car‘s manufacture will be reached safely
POWER LIFT HL 2 .60 SST DG
• lift for transporter with maximum
power reserve
• a control unit with oil-submerged
motor is supplied by SST cylinders
• self-purging system for the hydraulic
circuit
POWER LIFT HDL 6500 SST DG
POWER LIFT HDL 8000 SST DG
• absolute safety through Safety
Star Technology
• two control units with oil-submerged
motor are supplied by SST cylinders
• no floor connection
• double-jointed arms
• fast lifting and lowering times
• low maintenance and nearly
wear-free hydraulic cylinders
HYDR AULIC T WO -POST L IFTS
15
6.000KG | 6 .500KG | 8 .000KG
www.nussbaum-group.de/hl-sst-dg
OPTION: MINI-MAX ADAPTER
for HDL 6500 SST & HDL 8000 SST
Adapter for low clearance vehicles as well as
for deep-drawn side skirt and off-road vehicles:
• enormous adjustable range of 75–185mm
• multilevel quick adjustment
• operation by foot
• lifting capacity of the MINI-MAX adapter is reduced
to 4200kg
POWER LIFT HDL 6500 SST DG MB
approved version by Daimler. Double
jointed arms, special anticorrosive coa-
ting and several accessories as standard
scope fo supply.
H
E
F
G
Automotive L i f ts for passenger cars & transporters
L i f ts for passenger cars & transporters
Technical drawings for POWER L IFT
HL 2.50–2.60 SST & HDL 6500–8000 SST
Drawing for POWER LIFT HL 2.60 SST double-jointed arms &POWER LIFT HDL 6500 / 8000 SST double-jointed arms
17
www.nussbaum-group.de/hl-sst-dg
POWER LIFT HL 2.60 SST DG HDL 6500 / 8000 SST DG
Additional scope of delivery ONLY for Mercedes Benz approved
HDL 6500 SST DG MB
Document holder on column | Magnetic basket for wheel nuts | Height adaptersfor Sprinter and for G model with and without running-board | Integrated
CE Stop with acoustic warning signal
TO BE PREPARED BY CUSTOMER
Foundation min. (mm) 250 250
Concrete quality min. (normal reinforcement) C20/25 C20/25
Bolts (pcs) 14 20
Type of bolt (depends on foundation, see manual)
Hilti-V-5.8, M16 Hilti-V-5.8, M16
Air supply for energy set incl. incl.
Unloading (fork lift) required required
Hydraulic oil HLP ISO 32, approx. 17 liter per power unit HLP ISO 32, approx. 17 liter per power unit
POWER LIFT HL 2.60 SST DG HDL 6500 SST DG HDL 8000 SST DG
Lifting capacity (kg) 6000 6500 8000
Lifting/ lowering time approx. (sec) 65 / 65 70 / 55 70 / 55
Lifting height (mm) 2015 2150 2150
Lowest lifting point (mm)Version: Mini-Max
D 140–215115–190
170–240–
170–240–
Total height column (mm)Version: DG
J 4674–51244640–5090
3035–
3035–
Total width (mm) Version: DG
H 37504210
3570 (4370)–
3570 (4370)–
Drive-through width (mm) Version: DG
E 27602510
2376/2350–
2376/2350–
Column distance (mm) Version: DG
B 30602810
2766/2780–
2766/2780–
Arm extraction long (mm) Version: DG
F 931–18910–1890
1789/1834–
1789/1834–
Arm extraction short (mm) Version: DG
G 931–18910–1890
1789/1834–
1789/1834–
Power supply (V/Hz/A) 400/50/16 400/50/16 400/50/16
Motor (kW) 1,5 2 x 1,5 2 x 1,5
TO BE PREPARED BY CUSTOMER
Technical data
Automotive L i f ts for passenger cars & transporters
L i f ts for passenger cars & transporters
HEIGHT ADAPTERS
235TTKAS08873 · Height adap-ters for MB offroad vehicles GW 460/ 463 · adjustable 160 – 275 mm · set = 4 units
235TTKAS08850 · Height adapters for Sprinter (NCV3) with prism for rear pick-up point, adjustable 225–330 mm, set = 2 units
235TTKAS08837 · Height adap-ters for MB 100, adjustable 150 – 255 mm, set = 4 units
225SL08300 · Height adapter for the universal application · fixed 44mm · ø 120 mm · set = 4 units
Adjustable height adapters for universal application with ø 120 mm · set = 4 units
232SEL48593 · 154 – 245 mm232SEL48530 · 190 – 280 mm232SEL48560 · 239– 330 mm
232SL08610 · Height adapter for MB offroads GW 460/463 with footboard · fixed 145 mm · set = 4 units
Height adapter with U-profile for commercial vans at vehicle‘s frames – the U-Profile locks the vehicle · set = 4 units
232SL08850 · Adjustable range of 150 – 230 mm
232SEL48258 · Height adapter with prisms adapter, special for MB100 and similar use · fixed 145 mm · set = 4 units
Vehicle‘s frames – the U-Profile locks the vehicle · set = 4 units
250SL08130S · Adjustable range from 184–278 mm
235TTKAS08870 · Height adapters for Sprinter (NCV3) with positioning pin for front pick-up point, adjustable 230–335 mm, set = 2 units
used with...
Height adapters for Ford Mondeo ST 220, set = 2 units
250HDL28063 · Fixed height adapter for decreasing of lowest lifting point of approx. 15 cm · ø 120 mm · set = 4 units
232SL08840 · Adapter for frameadjustable for offroad vehicles and commercial vans · set = 2 units
232HEL48081 · Fixed height adapters for the universal appli-cation · fixed 151mm · ø 120mm · set = 4 units.
Adjustable height adapter for theuniversal application with ø 120 mm · set = 4 units
235TTKAS08501 · 115–220 mm235TTKAS08809 · 231–335 mm
Accessor ies for SMART L IFT & POWER L IFTACCESSORIES FOR TWO-POST LIFTS
FURTHER ACCESSORIES
Energy-set – optional integrated in the control or opposite column – and pneumatic tool support, screwed on column
Holder for height adapters
Screw tray galvanized – is inserted into the bracket of long arm, set = 2 units
Safety adapter for A-class is mounted under the vehicle in the traverse direction and prevents tilting of the vehicle by removing of equipment assembly
19
MINI-MAX – THE COMFORTABLE WORKSHOP ASSISTANT
further accessories on www.nussbaum-group.de/accessory
• height adjustable turntable
• for vehicles with low clearance as well
as for deep-drawn side skirt and off-
road vehicles
• quick adjustment of turntable
• enormous adjustable range
• multilevel grid quick adjustment
through pedal guarantees reliable and
comfortable positioning of lifting arms
• vehicle can be lifted higher by
reduction of no-load stroke
L I F T ING CAPACIT Y (KG) SMART L I F T POWER L I F T
3000 2.30 SL MM HL 2.30 NT MM
3500 2.35 SL MM HL 2.35 NT MM
6000 HL 2.60 SST DG
6500 HDL 6500 SST *
8000 HDL 8000 SST *
* with MINI-MAX-Adapter
www.nussbaum-group.de/accessory
MINI-MAX ADAPTER
• Mini Max adapter offers convenience
and safety by lifting passenger cars
• Mini Max adapter reduces the lifting
capacity of HDL 6500 SST and 8000 SST
to 4,200 kg
Automotive L i f ts for passenger cars & transporters
L i f ts for passenger cars & transporters
COMBI L IFTHYDRAULIC FOUR-POST LIFTS FOR PASSENGER CARS AND TRANSPORTERS
COMBI LIFT 4.40 S, 4.50 H, 4.65 H
& 4.80 H
• Powered by one hydraulic cylinder
under the runway and 4 steel ropes
• High capacity power unit with sub-
merged motor installed at the control
column.
• Control panel with push-button.
• Very flat runways with short access
ramps spare space in the workshop
• Adjustable runways width during the
installation to different car‘s track
width.
COMBI L IFT – FLEXIBLE FOR ANY APPLIC ATION ; REPAIR , T IRE SERVICE AND WHEEL ALIGNMENT
Filling boxes make runway as one level
The new generation of sliding plate convinces through its stability and free movement in cross direction, each 45mm left and right
Optional: turntables for wheel align-ment
Wheel-free lift with HyperFlow® Technology – length extendable in both sides from 1500–1900mm
ROBUST, MULTIFUNCTIONAL, POWERFUL
PERFECT FOR RELIABLE WHEEL ALIGNMENT
• High precision wheel alignment in every locking height thanks to the
adjustable latch strip with 100mm grid.
• The runways can be engaged in the next ratchet per push-button.
So called flat plates bring the runways with sliding plates and with or
without free wheel lift to a flat surface. Flat plates lay on the runways
without screws.
• Slip plates are mounted on roller bearings for an optimal strainless wheels
for the wheel alignment: sidewise +/- 50mm / lengthwise +/-1,5°.
VERSIONS
• flat runway
• PLUS – runway with wheel-free lift
• AMS – runway with mounted on
wheel alignment set
• PLUS AMS – runway with wheel-free
lift and wheel alignment set
21
4.000KG | 5.000KG | 6.500KG | 8.000KG
www.nussbaum-group.de/combilift
VARIOUS EQUIPMENT
OPTIONS
• JACK 2000 | JACK 2500 – air hydraulic axle jack
• LASER JACK – pneumatic axle jack
• Pneumatic joint play detector
• Lighting along the runway
Approved by Merces Benz and BMW for 4.50 SL
WHEEL-FREE LIFT (VERSION PLUS)
• Wheel-free lift, optional with
adjustable length of platform
• Lifting capacity 2500 - 3500kg
• Available in different lifting height
• Can be combined with wheel
alignment set
• Available for all models up to
COMBI LIFT 4.65 H
JOINT PLAY DETECTOR
• Joint play detector at the end of the runways
• One-man control with the button integrated in
the handel of the hand lamp
• For models up to COMBI LIFT 4.65 H
A
B
C
D
E
F
G
H
J
Automotive L i f ts for passenger cars & transporters
L i f ts for passenger cars & transporters
Technical drawings for COMBI L IFT
Quality of concretemin. C20/25
Fixed runway
Lighting (optional)
Adjustable runway
drive in direction
23
www.nussbaum-group.de/combilift
Technical drawings for COMBI L IFT
COMBI LIFT 4.40 S 4.50 H 4.65 H 4.80 H
Foundation min. (mm) 160 250 160 X
Concrete quality min. (normal reinforcement)
min. C20/25 min. C20/25 min. C20/25 min. C20/25
Bolts (pcs) 16 16 16 16
Type of bolt (depends on foundation, see manual)
Hilti-V-5.8, M10 Hilti-V-5.8, M10 Hilti-V-5.8, M10 Hilti-V-5.8, M10
Hydraulic oil HLP ISO 32 (liters) 10 10 10 17
Power supply (V / Hz / Amp.) 400 / 50 / 16 400 / 50 / 16 400 / 50 / 16 400 / 50 / 16
Time-lag fuse (mm²) 5 x 2,5 5 x 2,5 5 x 2,5 5 x 2,5
Unloading (fork lift) required required required required
TO BE PROVIDED BY CUSTOMER
Technical data
COMBI LIFT 4.40 S 4.50 H 4.65 H 4.80 H
Lifting capacity (kg) 4000 5000 6500 8000Lifting capacity WFH (kg) version: Plus & Plus AMS
3000 3500 3500 –
Lifting capacity JACK (kg) 2000 2500 2500 5000
Lifting/ lowering time approx. (sec) 40 / 35 35 / 35 41 / 36 45 / 30
Lifting/ lowering time WFL (sec) version: Plus & Plus AMS
15 / 5 12 / 8 12 / 8 –
Lifting height (mm) A 1976 1935 1980 1800
Lifting height AMS (mm) version: AMS & Plus AMS
2008 2030 2030 –
Lifting height WFL (mm) version: Plus & Plus AMS
525 440 440 –
Runway length (mm)Usable runway length (mm)
B 48304600
5540–
5540–
6000–
Runway width (mm) C 500 670 670 670
Distance between columns (mm) D 834–984 830–930 830–930 –Platform length WFL (mm) version: Plus & Plus AMS
1530–1900 1550–1900 1550–1900 –
Drive-on height (mm) E 160 190 190 217Drive-on height AMS (mm) version: Plus & Plus AMS
210 240 240 –
Drive-on height AMS (mm) version: Plus & Plus AMS
50 68 68 –
Drive-on height WFL (mm) version: Plus & Plus AMS
J 1000 1250 1250 1250
Total height column (mm) F 2162 2320 2320 2328
Total length (mm) G 5950 6965 6965 7570
Total width (mm) H 3260 3540 3540 3550
Motor (kW) 3,0 3,0 3,0 3,0
Power supply (V/Hz) 400 / 50 400 / 50 400 / 50 400 / 50
Automotive L i f ts for passenger cars & transporters
L i f ts for passenger cars & transporters
Hydraulic scissor lift with two independent hydraulic circuits.
UNI L IFT NT
FUNCTIONALITY & SAFETY – NT TECHNOLOGY
• Redundant hydraulic system with two independent
hydraulic circuits
• Powerful, quiet and long lasting oil-submerged motor
VERSIONS
• AMS – wheel alignment set with rear
sliding plates and flat plates with recess
for turning tables. Additional pneumatic
mechanical latch for alignment purpos
• PLUS – flat runways with wheel-free lift
• PLUS AMS – runway with wheel-free lift
and wheel alignment set
HYDRAULIC SCISSOR LIFT
UNI LIFT 3500 & 5000 NT
• Thanks to the redundant hydraulic system
no safety mechanic latch is necessary.
• R-strong build with low profile runways
and short access ramps save space in the
workshop.
• No hard connection between the runways.
More comfort and safety.
• Easy to install, 2 version above ground or
flushed installation.
• Powerful hydraulic unit with oil submer-
ged motor.
• Sliding blocks made from synthetic materi-
al glide on stainles steel guides and ensure
quite operation and almost wear free
mechanism.
UNI LIFT 3500 & 5000 NT UNI LIFT 3500 & 5000 NT PLUS, in-ground installationUNI LIFT 3500 & 5000 NT PLUS AMS with axel JACK, above-ground installation
UNI L IFT NT – THE PROFESSIONAL SOLUTION FOR ANY WORKSHOP
25
3.500KG | 5.000KG
www.nussbaum-group.de/unilift
VARIOUS OPTIONS AVAILABLE
• JACK 2000 / 2500 - air hydraulic axle jack
• LASER JACK – pneumatic axle jack
• Joint Play Detector
• lighting along the runways
• extensions for the runways
WHEEL-FREE LIFT (PLUS VERSION)
• Wheel-free lift, optional with adjustable length of
platform
• Lifting capacity 3500kg
• Available in different lifting heights
• Can be combined with wheel alignment set
Runway profile. Optional OXIGEN CARE. Wheel-free lift with adjustable platformRear sliding plate
PERFECT FOR RELIABLE WHEEL ALIGNMENT
• High precision wheel alignment in every locking height
thanks to the adjustable latch strip.
• The runways can be engaged in the next ratchet per
push-button.
• So called flat plates bring the runways with sliding plates
and with or without free wheel lift to a flat surface. Flat
plates lay on the runways without screws.
• Slip plates are mounted on roller bearings for an opti-
mal strainless wheels for the wheel alignment: sidewise
+/- 50mm / lengthwise +/-1,5°.
SURFACE TREATMENTS:
Powder coated, fire galvanized, OXYGEN care
Automotive L i f ts for passenger cars & transporters
L i f ts for passenger cars & transporters
UNI L IFT Wheel Al ignment ProHYDRAULIC SCISSOR LIFT FOR WHEEL ALIGNMENT
The high requirements for an accurate wheel alignment is also a challenge for the alignment lift.
The UNI LIFT with its unique technology is the answer to these demands.
UNI LIFT 5500 QUATTTO AMS PRO
• wear-free kinematic, without deflection lever
• adjustable wheel-free lift for smart up to S-class
• runway length: 5200 mm
FUNCTIONALITY & SAFETY
• 4 cylinders provide permanent security in any lifting height
through patented safety system SST
• Electronic controlled synchronization through proportional valve
technique
Wheel-free lift Turntable with flat plates on one levelExtented drive-on ramps
• for wheel alignment of modern vehi-
cles: accuracy ± 0,5 mm right / left ± 1
mm front / rear or diagonal
• precise wheel alignment and perma-
nent repeatable measuring data
• very compact and low construction
with short access ramps, ideal also for
low clearance vehicles
• no fixed connection between the
runways
HYMA X X – HYDRAULIC SCISSOR LIFT FOR WHEEL ALIGNMENT
27
UNI L IFT Test ProHYDRAULIC SCISSOR LIFT FOR FAST INSPECTION
UNI L IFT 4000 NT QUATTRO &
UNI L IFT 5000 NT QUATTRO
• with integrated lengthwise adjustable
wheel-free lift
• pneumatic play detector with hand-lamp,
cable or remote control
• a silent, powerful control unit is integrated
into a canister foundation between the
runways
• runway lengths: 4500 mm (UNI L IFT 4000
NT QUATTRO) or 5000 mm (UNI L IFT 5000
NT QUATTRO)
• the lift is intended for in-ground instal-
lation – optional with accessible working
platform for canister foundation.
• vertical roll-off protector integrated in
runways
• optional: floor compensation for axle jack
The specialists for fast and efficient inspection processes.
FUNCTIONALITY & SAFETY
Redundant hydraulic system with two independent
hydraulic circuits ensures synchronization and security.
Joint play detector Axle jack LASER JACKRoll-off protection - integrated in runway
HYMA X X – HYDRAULIC SCISSOR LIFTS FOR TRANSPORTER AND SMALL TRUCK
L i f ts for passenger cars & transporters
UNI LIFT 6000 & 8000
• Space-saving, hydraulic scissor lift
with lifting capacity of 6.000 kg and
8.000 kg
• Equipped with flat runways, ideal to
lift transporters up to light trucks
• No fixed connection between the
scissors
• Low construction height allows an
easy drive-on without long drive-on
ramps
• Installation above ground with til-
ting flaps or flushed installation with
access ramps bolted to the floor.
FUNCTIONALITY AND SAFETY
• Approved master / slave system guarantees the synchronization of both
scissors units.
• Mechanical latches serve as security device.
• High performance oil-submerged power unit ensures a quiet operation
and short lifting and lowering times.
UNI L IFT 6000 & 8000 – HYDRAULIC SCISSOR LIFTS FOR TRANSPORTERS AND LIGHT TRUCKS
Compact construction height Low drive-on height - easy to drive-on No fixed connection between the scissors
UNI L IFT 6000 & 8000HYDRAULIC SCISSOR LIFTS FOR TRANSPORTERS AND LIGHT TRUCKS
OPTIONS AND ACCESSORIES:
• Runway length: 5500 mm (standard)
• Fully galvanized lift including galva-
nized runways
• Lighting with 4 flourescent lamps,
integrated in the runways
• Middle point lifter
• JACK 2000 – air hydraulic axle jack
• JACK 2500 – air hydraulic axle jack
(for UNI LIFT 8000)
• Extention of hydraulic hose
29
www.nussbaum-group.de/accessories
JOINT PLAY DETECTOR
• Installed at the end of runways
• One-hand-operation by halogen lamp with integrated push
button, cable connected or radio control (optional)
JACK 2000 · JACK 2500
• Air hydraulic axle jack
• Universal lifting at outer pick-up
points without spring relieving,
or in the middle
• Movable along the runways
• Extendable lifting arms
• With mechanical safety ratchets in
2 heights
• Min. air pressure 6 bar
JACK 2000 2500 L ASER JACK Lifting capacity (kg) 2000 2500 2000
Lifting height (mm) 370 270 270
Lifting time (sec.) 35 35 20
Lowering time (sec.) 7 7 15
Arm extraction (mm) 800–1640 810–1760 690–1495
Motor (kW) – – 1,5
Power supply (WHz) – – 400/50
Further accessories on www.nussbaum-group.de/accessories
Flat plates installation cassette Optional with park position for axle jack
Vertical roll-off protectors for in-ground installation
Accessor ies for COMBI L IFT & UNI L IFTACCESSORIES FOR FOUR-POST LIFT AND SCISSOR LIFT
LASER JACK
• Pneumatic axle jack
• Lift vehicle at outer pick-up
points of axis
• Movable along the runways
• Extendable lifting arms
• Min. air pressure 6 bar
ACCESSORIES FOR FOUR-POST LIFT AND SCISSOR LIFT
JACK 2000
JACK 2500
LASER JACK
A
B
C
D
E
F
G
Automotive L i f ts for passenger cars & transporters
L i f ts for passenger cars & transporters
Technical drawings for UNI L IFT
wheel-free lift
sliding plate
drive in directionturntable
operating unit
31
www.nussbaum-group.de/unilift
TO BE PREPARED BY CUSTOMER
UNI LIFT 3500 NT 5000 NT5500
AMS PRO4000 NT
QUATTRO5000 NT
QUATTRO6000 8000
Concrete quality min. C20/25
Bolt (pcs) 12 12 20 16 16 12
Hydraulic oil HLP ISO 32
Type of bolt (depends on foundation, as described in manual) Hilti-V-5.8, M12
Hydraulic oil (liter) approx. 13 approx. 14 approx. 10 approx. 16 approx. 42 approx. 10
Time-lag fuse 5 x 2,5 mm²
Power supply 400V / 50 Hz / 16 Amp.
Unloading (fork lift) required
* for version: PLUS | PLUS AMS ** AMS = mounted-on wheel alignment set
Technical data
UNI L I F T3500
NT5000
NT5500
AMS PRO4000 NT
QUAT TRO5000 NT
QUAT TRO6000 8000
Lifting capacity (kg) version: PLUS | PLUS AMS
40003500
50005000
5000 4000 5000 6000 8000
Lifting capacity wheel-free lift (kg) * 3500 3500 3500 3500 3500 –
Lifting/ lowering time approx. (sec.) 35/29 31/19 31/25 26/26 27/19 40/40
Lifting height (mm) A 1920 1920 1940 2090 2090 1927
Lifting height WFL (kg)version: PLUS
B 580530
580530
––
500–
532–
––
Runway width (mm) C 635 635 635 610 610 788
Runway length (mm) D 4500 5000 5200 4500 5000 5500
Platform length wheel-free lift (mm) E 1485–1945 1485–1945 – 1471–2147 1459–1937 –
Drive-on height runway (mm)Drive-on height wheel-free lift (mm)Drive-on height AMS (mm)
F 195+50+18
195+50+18
220+50
–
220––
225––
–215–
Total length above-ground (mm) G61556355
6655 6275 4610 5122 7160
Total width (mm) 2120 2170 2290 2120 2080 2340
Motor (kW) 3,0 3,0 3,0 2 x 3,0 2 x 3,0 3,0
Power supply (V/Hz) 400/50 400/50 400/50 400/50 400/50 400/50
1460mm
2160mm (2060mm*)
Automotive L i f ts for passenger cars & transporters
L i f ts for passenger cars & transporters
MA XIMUM LIFT ING HEIGHT
effective lifting stroke of 2000 mm – enough space
under the vehicle, also for in-ground installation
JUMBO LIFTHYDRAULIC DOUBLE-SCISSOR LIFTS
FREE ACCESS
between the scissors, there is no mechanical
connection between platforms
SAFE AND FLEXIBLE PL ATFORM
easy to extend through lengthwise adjustable
lifting platform for picking up a wide range of
vehicles
L IFT ING OF VITO, V IVARO UP TO V W T5 WITH
SHORT WHEEL BASE
Follow the trend for workshops – lifting heavy vehicles such
as SUVs, 4-wheel vehicles up to VW T5 with short wheel base
and comparable.
VW UP
JUMBO LIFT – THE RIGHT SOLUTION FOR ANY WORKSHOP
JUMBO LIFT 3200 NT – For vehicles up to VW T4 with short wheel base and similar vehicles. Above-ground installation only.
33
3.200KG | 3.500KG | 4.000KG
www.nussbaum-group.de/jumbolift
HyperFlow
HyperFlowCOMPACT
®
JUMBO LIFT – THE RIGHT SOLUTION FOR ANY WORKSHOP
JUMBO LIFT 3500 NT – lifting from VW Up up to VW T5 with short wheelbase without a problem
NT TECHNOLOGY = PERFEC T & SMOOTH
RUNNING POWERFUL , SAFE, STEADY
the redundant fully hydraulic system guarantees maximum
operating safety through using two independent
hydraulic circuits
LONG LIFE, THANKS TO FULLY HYDR AULIC SYSTEM
• no need of safety ratchet
• no electrical and pneumatic components at the lift
Special color extra charge
LONG LIFEC YCLE & STABLE
• lubricating nipples at the bolts provide an easy
maintenance and secure a long lifecycle
• high quality steel construction ensures directional
stability
HyperFlow TECHNOLOGY
• the synchronization is automatically set / adjusted at all
times during operation
• automatic purging of the hydraulic system during
operation
JUMBO LIFT 4000 NT – lifting vehicles from VW T5 with short wheelbase and similar vehicles | In-ground installation
Flaps to increase the length of the ramps, easy to lock and unlock with one hand
FL AT CONSTRUC TION
low construction height enables an above-ground installati-
on and driving-on, even with low clearance vehicles
A
B
C
D
E
Automotive L i f ts for passenger cars & transporters
L i f ts for passenger cars & transporters
Technical drawings for JUMBO LIFT
A
B
C
D
E
drive in direction
cable channel
35
www.nussbaum-group.de/jumbolift
THE R IGHT ACCESSORIES – THE PERFECT SOLUT ION FOR EVERY APPL ICAT ION... 3200 3500 4000
Truncated pyramid pad • • •
Polymer pad 50 x 150 x 340mm • • •
Polymer pad 100 x 150 x 340mm • • •
Tuning ramps for low or sports cars, set = 4 units • • –
CE-Stop for in-ground installation (standard equipment) – – •
OPT ION : SUFR ACE TREAT ING
Oxygen care coated for corrosive environment (dark grey) • • •
TO BE PREPARED BY CUSTOMER
JUMBO LIFT 3200 NT / 3500 NT / 4000 NT
Foundation min. (mm) 160
Concrete quality min. (normal reinforcement) min. C20/25
Bolts (pcs) 12
Type of bolt (depends on foundation, see manual)
Hilti-V-5.8, M10
Hydraulic oil HLP ISO 32 (liters) approx. 13
Power supply (V / Hz / Amp.) 400 / 50 / 16
Time-lag fuse (mm²) 5 x 2,5
Unloading (fork lift) required
Technical data
JUMBO L I F T 3200 NT 3500 NT 4000 NT
Lifting capacity (kg) 3200 3500 4000
Lifting time approx. (sec) 36 36 36
Lifting height (mm) A 2000 2000 2000
Drive-on height (mm) B 105 105 –
Installation depth (mm) B 105 105 135
Total width (mm) C 2020 2020 2020
Platform width (mm) D 610 610 610
Platform length (mm) E 1460 – 2060 1460 – 2160 1460 – 2160
Motor (kW) 3,0 3,0 3,0
Power supply (V/Hz) 400/50 400/50 400/50
Automotive L i f ts for passenger cars & transporters
L i f ts for passenger cars & transporters
ADDITIONAL WORKING SPACE
An additional working space in your work-
shop for fast working at any vehicle. The
midrise sprinter mobil is an efficient and
mobile solution for tire service, painting
and body work.
• Lifting height approx. 1000mm
• Anti -skid lifting platforms are galvanized
and lengthwise adjustable
SPRINTER mobil 2500
SPRINTER MIDRISE LIFT
SPRINTER MOBIL – YOUR ADDITIONAL WORKING SPACE
MAXIMUM FLEXIBILITY
can be installed without screws
on almost every flat and solid
surface
MOBIL-SET ( OPTIONAL)
can be moved without any problem
with Mobile-Set
Flaps to increase the length of the ramps, easy to lock and unlock with one hand
37
2.500KG | 3.000KG
www.nussbaum-group.de/sprinter
SPRINTER mobil 3000
FULLY HYDRAULIC SYSTEM
the hydraulic system of the lift works with two indepen-
dent cylinders. A special safety device in the hydraulic
circuit substitutes the conventional security latches and
protects the lift from sagging. The mechanic synchroni-
zation is done by torsion bars at the bottom of the lift.
SOLID STEEL CONSTRUC TION
HIGH-PERFORMANCE POWER UNIT
the high-performance oil-submerged motor in the power
unit with push buttons guarantees short lifting and lowering
times.
FAST AND EASY TO SET UP
the lift is fully assembled at the factory and tested.
To set up the lift, it will be unpacked, only filled with
hydraulic oil and connected to a suitable electrical
connection.
A
B
CC
D
D
E
E
Automotive L i f ts for passenger cars & transporters
L i f ts for passenger cars & transporters
Technical drawings SPRINTER
X: vehicle with front engine
XX: vehicle with rear engine
39
www.nussbaum-group.de/sprinter
OPT IONS & ACCESSORY
Fire galvanization of scissors and base plate for corrosive environment
Polymer pads • 50 x 150 x 340mm
Polymer pads • 100 x 150 x 340mm
Truncated pyramid pad
Tuning ramps for low or sports cars, set = 4 units
SPR INTER MOBIL 2500 3000
Bolts (pcs) 8 bolts when the lift should be fix installed
Type of bolt (depends on foundation, see manual) Hilti-V-5.8, M10
Hydraulic oil HLP 32 (liters) approx. 8
Power supply (V / Hz / Amp.) 400 / 50 / 16
Time-lag fuse (mm²) 5 x 2,5
Unloading (fork lift) required
TO BE PREPARED BY CUSTOMER
Technical data
SPRINTER MOBIL 2500 3000
Lifting capacity (kg) 2500 3000
Lifting time approx. (sec) 11 11
Lifting height (mm) A 980 980
Drive-on height (mm) B 102 102
Total width (mm) C 1910 1910
Platform width (mm) D 450 450
Platform length (mm) E 1400 – 2010 1400 – 2010
Motor (kW) 1,5 1,5
Power supply (V/ Hz) 400/50/16 400/50/16
Automotive L i f ts for passenger cars & transporters
L i f ts for passenger cars & transporters
TOP L IFT
1-PISTON IN-GROUND LIFT
• 1-piston lift with external power unit
• Separated control panel can be installed up to 5 m away from the lift
X-LIFTING ARMS
• Fire galvanized, 2-times
telescopic lifting arms
• Vehicle will be lifted at
pick-up points,
therefore sillboard is acces-
sible
• Wide range of height adap-
ters available
www.nussbaum-group.de/
accessory
H-LIFTING PLATFORM
• Fire galvanized, lengthwise
adjustable lifting platform
for picking up vehicles at
sillboard
• Fast and simple to drive-on
for a wide range of vehicles
DRIVE TECHNOLOGY:
• Hydraulic unit with oil-sub-
merged motor integrated in
cannister
• A crossbeam secures syn-
chronization and prevents
rotation of the platform
• Screwed, corrosion resistant
hydraulic pipes from hy-
draulic unit to the cylinders
(no loose flexible hoses)
• Cylinders are protected
inside the hard chromed
guiding pipes
TOP L I F T 1.35 H X
Lifting capacity (kg) 3500 3500
Lifting height (mm) 1975 2064
Lifting/ lowering time (sec.) 40/35 40/35
Piston diameter (mm) 140 140
Arm extraction (mm) — 630–1235
Lowest pick-up point (mm) — 95
Platform length (mm) 1400–1900 —
Drive-on height (mm) 60 —
Installation depth (mm) 2520 2520
Motor (kW) 3 3
Power supply (V/Hz) 400/50 400/50
41
www.nussbaum-group.de/toplift
YOUR WORKSHOP IN AN ATTRACTIVE APPEARANCE
WITH
• 2-piston lift with lifting arms,
lifting platform and runways up to 8t
WITH DIFFERENT INSTALLATION VARIATIONS
• TS – 2,50m installation depth
• TTL NT – 1,75m installation depth
TS – HYDRAULIC MECHANICAL
• Cassette with mechanical crossbeam
• Synchronization is ensured by a mechanical connec-
tion of the pistons
• Crossbeam ensures synchronization of the piston and
has an anti-twist function.
• Installation depth: 2,50m
THE LIFTING PISTON
• Hydraulic cylinders are integrated in guiding pipe and are
treated against corrosion with a chromium coating
• Hard piping instead of flexible tubes ensures a long-life and
low maintenance
TTL NT TECHNOLOGY
• Redundant hydraulic system with two independent hydraulic circuits.
• No mechanical latch is necessary. Few wear-out and disruptive parts.
• No crossbeam between cylinders is necessary
• The two single pistons ease the installation
• Hydraulic pump is fixed to one of the cylinders
• Emergency lowering is possible from outside with compressed air
• Lifting height 2m
• Telescopic pistons for a reduced installation depth max. 1,75m
TOP L IFT2-PISTON IN-GROUND LIFT
L i f ts for passenger cars & transporters
2.35 TSK 2.35 T TL K NT 2.50 T TK AS 2.50 T TL K NT
TOP L I F T STD DG MM STD DG MM DG DG
Lifting capacity (kg) 3500 3500 3500 3500 3200 3500 5000 5000
Lifting height (mm) 2070 2050 2070 2085 2085 2085 1990 2085
Lifting/ lowering time (sec.) 30/30 30/30 30/30 20/20 20/20 20/20 43/32 45/27
Piston diameter (mm) 140 140 140 172, 140 172, 140 172, 140 160 172, 140
Distance between pistons (mm)
2200 2200 2200 variabel variabel variabel 2600 variabel
Arms extraction (mm) 595–987 0 – 1789 595–987 595–1160 0–1789 618–943 0–1790 0–1790
Lowest pick-up point (mm) 83–120 115 – 190 75 – 185 115–190 115–190 75 – 185 115–190 115–190
Installation depth (mm) 2493 2493 2493 1463 1463 1463 2350 1463
Motor (kW) 3 3 3 3 3 3 3 3
Power supply (V/Hz) 400/50 400/50 400/50 400/50 400/50 400/50 400/50 400/50
*1 Mini Max-arm: 75–185mm
• Sillboard remains free
• Flexibility for working at a wide range of vehicles from small cars to vans
and off-road vehicles
• Ideal for most of the works around the vehicle: body works, demounting
big components, working with vans and small trucks, etc.
STANDARD (STD)
• Powder coated 2-times telescopic lifting arms with
adjustable turntables
• For passenger cars and small vans
MINI-MAX (MM)
Suitable for lifting vehicles with low clearance and
deep-drawn side skirt:
• Enormous adjustable range of 75–185mm
• Multilevel quick adjustment
• Operation with foot
• Plug on adapter especially for passenger cars, adjustable
range of 85–185mm. Lifting capacity max. 4.200 kg
(for 2.50 TTKAS and TTL K SST)
DOUBLE-JOINTED ARMS (DG)
Unique construction with double-jointed per lifting arm for
• Reaching 100% of pick-up points
• Easy lifting of passenger cars through 90° of lifting arms
positioning
TOP L IFT with l i f t ing arms2 PISTON IN-GROUND LIFT
43
www.nussbaum-group.de/toplift
TOP L IFT with l i f t ing platform2 PISTON IN-GROUND LIFT
• Fast lifting
• Maximum accessibility
• Unrestricted work on axes and wheels
• Minimum space required
• Low construction – only 58 mm
STANDARD (STD)
• Adjustable lengthwise
• Fully galvanized platform
• Length- and crosswise traversable
• Optional rubber plates replace poly-
mer pads for fast lifting at sillboard
UNIVERSAL (UNI)
• Complete length- and crosswise
adjustable
• Powder coated platform
• Drive-on ramps are adaptable to floor
unevenness
XY LIFTING PLATFORM
• Length- and crosswise adjustable for
optimal achievement of pick-up points
• Fully galvanized platform
• Incl. 4 rubber plates
TOP L I F T
2.35 TS 2.35 T TL TS NT
STD X Y UNI X Y UNI
Lifting capacity (kg) 3500 3500 3500 3500 3500
Lifting height (mm) 2010 2069 2069 2085 2085
Lifting/ lowering time approx. (sec.)
30/30 30/30 30/30 20/20 20/20
Piston diameter (mm) 140 140 140 172, 140 172, 140
Distance between pistons (mm)
1280 1280 1280 variable variable
Platform length (mm) 1600–2400 1524–2107 1400–1930 1536–2120 1400–1930
Platform width (mm) — 890–1817 650–1990 710–1750 650–1990
Platform (mm) 426 365 450 415 450
Drive-on height (mm) 60 77 60 77 60
Installation depth (mm) 2493 2493 2493 1458 1458
Motor (kW) 3 3 3 3 3
Power supply (V/Hz) 400/50 400/50 400/50 400/50 400/50
L i f ts for passenger cars & transporters
TOP L IFT with runways2 PISTON IN-GROUND LIFT
2.35 TSAP H 2.50 TTAP & 2.50 TTAP H 2.35 TSAP with alignment support
• Smooth drive-on
• Safe lifting
• Easy positioning
• Low drive-on height (140mm)
• Possible to install above-ground or in-ground
TSA & TTL A – flat runway
• Flat runway
• Optional axle jack
TTA – flat runway with lifting
capacity of 5t
• Drive-on ramps for transporter
and small trucks
• Flat runway
• Optional axle jack
TSAP – „piston in piston“
• Runway + wheel-free lift with short
stroke
• Wheel-free lift: adjustable lengthwise
with short stroke
• Runway with low drive-on height
• Illustration shows INOX Design (opti-
on)
TSAP H – „2 in 1“
• Runway + wheel-free lift is adjustable
in drive-on direction and operates to
full stroke
• The runway and wheel-free lift
operate independently from each
other to the full lifting stroke
• Illustration shows INOX Design (opti-
on)
45
www.nussbaum-group.de/toplift
OPTIONS
• JACK 2000 · JACK 2500
Air hydraulic scissor axle jack with
lifting capacity of 2.000kg and 2.500kg
for an universal pick-up vehicles,
either at the outer points of the axis
without relief of the suspension or in
the center of the axis.
• LASER JACK
Pneumatic scissor axle jack with lifting
capacity of 2.000kg to pick-up vehicles
at the outer points of the axis.
• Lighting
Integrated lighting at the runways,
make working under the body work
easier.
• Installation cassette
Preventing mistakes of foundation
works by using of installation cassette.
TOP L I F T 2.35 TSA 2.35 T TL A 2.35 TSAP 2.35 TSAP H 2.50 T TA 2.50 T TA P 2.50 T TA P H
Lifting capacity (kg) 3500 3500 3500 3500 5000 5000 5000
Lifting height (mm) 2040 2085 1920 2080 1970 1870 1970
Lifting/ lowering time approx. (sec) 30/30 20/20 28/25 32/32 43/32 43/32 43/32
Piston diameter (mm) 140172140
172 140 (RFH)
172 140 (RFH)
160 160 160
Distance between pistons (mm) 1280 variable 12501650
RFH: 12501500 1500
1500 RFH: 2600
Arm extraction (mm) — — — — — 450–1255 450–1255
Lowest pick-up point (mm) — — — — — 140–215 115–190
Lifting height wheel-free lift (mm) — — 400 1900 — 675 1990
Lifting platform length (mm) — — 1529–1949 1400–1900 — — —
Drive-on height (mm) 140 140 140140
ID: 160170 170 170
Runway length (mm) 4400 4400 4400 4200 4800 4800 4800
Runway width (mm) 596 596 605 610 700 700 700
Total length above-ground (mm) 4920 4920 5165 5273 5790 5450 5790
Total width (mm) 2042 2042 2050 1994 2300 2300 2300
Installation depth (mm) 2493 1605 2500 2500 2350 2350 2350
Motor (kW) 3 3 3 3 3 3 3
Power supply (V/Hz) 400/50 400/50 400/50 400/50 400/50 400/50 400/50
TTAP – „piston in piston“
• Integrated lifting arms as wheel-free
lift, ideal for the car reception area
and for diagnosis, as well as work on
wheels
• For transporters and small trucks
• Wheel-free lift with short stroke
• Runway length: 4.800mm
TTAP H – „2 in 1“
• The runways and the wheel-free lift
with carrying arms work independent-
ly of each other. Both have a lifting
height of approx. 2m.
„You are actually getting 2 lifts in
one“
Automotive L i f ts for passenger cars & transporters
L i f ts for passenger cars & transporters
We replace your old piston l i f tsLIFTS FOR EXISTING INSTALLATION CANISTERS
ADVANTAGES
• Lifting capacity 3,5t to 5t possible
• No change of lifting height – cylinder stroke 2m!
• Lower installation depth (max. 1750mm)
• Different piston distances are possible
(NUSSBAUM standard: 1280mm, 2200, (2300mm), 2600mm)
• Different load suspension devices are possible (flat lifting
platform & support arms)
• Easy assembly through telescopic-single piston
• Internal hydraulic unit (standard) with wall tableau or
external control unit possible
• No safety ratchet necessary
• No gear rack besides the lifting piston
• No cross beam between the lifting pistons is necessary
• No compressed air is necessary for the function of the lift
• Emergency lowering from outside with internal control unit
(with compressed air)
• Installation is possible independently from the installation
depth of the existing canister
• Hydraulic unit is fixed on the lifting piston.
• Available position of the existing empty pipe can be used
Numerous in-ground piston lifts, also from other manufacturers, are in use for many years. Several of those lifts are now
getting old. Sometimes those types of lifts are not produced anymore or a repair is not worth it. The NUSSBAUM new in-
ground piston lift – TOP LIFT TTL NT can be placed in existing installation canisters with relatively low effort – independent-
ly from the manufacturer.
TO BE PREPARED BY CUSTOMER & SCOPE OF DELIVERY
TOP LIFT TTL NT
SCOPE OF DELIVERY
Lifting unit (2 telescopic lifting pistons)
Installation frame with cover
Internal hydraulic unit (standard), control unit at the wall
Load suspension device depending on distance between pistons and the loading capacity
TO BE PREPARED BY CUSTOMER
Power supply 3PH,N+PE,400V,50Hz
Protection 16 ampere fuse
47
www.nussbaum-group.de/toplift
1
2
3
4
5
6 7 8
HyperFlow
HyperFlowCOMPACT
®
PROCEDURE:
Only a few steps to your new l i f t!
Picture 1:
Disassembly of the existing lift
Picture 2:
Uncover the concrete around the installation canister
Picture 3:
Seperate the upper frame from the lower part of the existing installation canister
Picture 4:
Insert the installation frame, adjust and fix it with fixation anchors
Picture 5:
Set the concrete reinforcement. Set the installation frame in concrete
Upper edge frame = upper edge of the finished floor
Picture 6:
Insert the TTL NT lifting device with a fork lift and fix it
Connect the electric and hydraulic pipes. Perform a trial
Picture 7 / 8:
Assemble cover and load suspension device and test with vehicle
Recommended