View
243
Download
4
Category
Preview:
Citation preview
This is a repository copy of Investigation on synchronous reluctance machines with different rotor topologies and winding configurations.
White Rose Research Online URL for this paper:http://eprints.whiterose.ac.uk/119473/
Version: Accepted Version
Article:
Ma, X.Y., Li, G. orcid.org/0000-0002-5956-4033, Zhu, Z.Q. et al. (2 more authors) (2017) Investigation on synchronous reluctance machines with different rotor topologies and winding configurations. IET Electric Power Applications. ISSN 1751-8660
https://doi.org/10.1049/iet-epa.2017.0199
This paper is a postprint of a paper submitted to and accepted for publication in IET Electric Power Applications and is subject to Institution of Engineering and Technology Copyright. The copy of record is available at the IET Digital Library.
eprints@whiterose.ac.ukhttps://eprints.whiterose.ac.uk/
Reuse
Unless indicated otherwise, fulltext items are protected by copyright with all rights reserved. The copyright exception in section 29 of the Copyright, Designs and Patents Act 1988 allows the making of a single copy solely for the purpose of non-commercial research or private study within the limits of fair dealing. The publisher or other rights-holder may allow further reproduction and re-use of this version - refer to the White Rose Research Online record for this item. Where records identify the publisher as the copyright holder, users can verify any specific terms of use on the publisher’s website.
Takedown
If you consider content in White Rose Research Online to be in breach of UK law, please notify us by emailing eprints@whiterose.ac.uk including the URL of the record and the reason for the withdrawal request.
1
Investigation on Synchronous Reluctance Machines with Different Rotor Topologies and Winding Configurations X. Y. Ma, G. J. Li, Z. Q. Zhu, G. W. Jewell, J. E. Green
Department of Electronic and Electrical Engineering, University of Sheffield, Sheffield, S10 2TN, U.K. g.li@sheffield.ac.uk.
Abstract: This paper investigates the influence of rotor topologies and winding configurations on the electromagnetic performance of 3-phase synchronous reluctance machines with different slot/pole number combinations, e.g. 12-slot/4-pole and 12-slot/8-pole. Transversally laminated synchronous reluctance rotors with both round flux barrier and angled flux barrier have been considered, as well as the doubly-salient rotor as that used in switched reluctance machines. Both concentrated and distributed winding configurations are accounted for, i.e., single layer and double layer conventional and mutually coupled windings, as well as fully-pitched winding. The machine performance in terms of d- and q-axis inductances, on-load torque, copper loss, and iron loss have been investigated using 2-D finite-element analysis. With appropriate rotor topology, 12-slot/4-pole and 12-slot/8-pole machines with fully-pitched and double layer mutually coupled windings can achieve similar torque capacity, which are higher than the machines with other winding configurations. In addition, the synchronous reluctance machine with round flux barrier can have lower iron loss than doubly salient reluctance machine under different working conditions. The prototypes of 12-slot/8-pole single layer and double layer, doubly salient synchronous reluctance machines have been built to validate the predictions in terms of inductances and torques. Nomenclature DSRM Doubly Salient Reluctance Machine SynRM Synchronous Reluctance Machine RFB Round Flux Barrier AFB Angled Flux Barrier DLC Double Layer Conventional DLMC Double Layer Mutually Coupled SLC Single Layer Conventional SLMC Single Layer Mutually Coupled FP Fully-Pitched
1. Introduction
COMPARED with permanent magnet machines and induction machines, both the synchronous
reluctance machines (SynRM) and the switched reluctance machines (SRMs) are becoming increasingly
attractive in various applications ranging from domestic appliances to electrical vehicles and hybrid
electrical vehicles (EVs and HEVs). This is mainly due to their magnet-free features and hence low cost,
simple and robust rotor structures (without rotor conductors and hence no rotor copper losses), and
hence very suitable for high speed and harsh environment applications [1]-[4]. In general, the SynRMs
use standard 3-phase pulse width modulation (PWM) inverters while the SRMs require an
2
unconventional power-converter due to the square wave unipolar current supply (usually 120 degrees
conduction for 3-phase SRMs) [1], [5]. This to some extent limits the wider industrial penetration of the
SRMs. In order to employ the standard and off-the-shelf 3-phase inverter as that used in SynRMs so to
reduce the system cost, in [5]-[7], the SRMs have been supplied with 3-phase sinewave currents, which
are in effect short-pitched doubly salient reluctance machines (DSRMs).
Similar to the induction machines, the classic SynRMs often employ the distributed stator
windings [8]. However, many permanent magnet machines and DSRMs adopt the fractional-slot
concentrated windings due to their inherent advantages such as higher slot fill factor, shorter end-
winding, smaller machine overall footprint, etc. [9]-[11]. When a fractional slot, double layer (DL)
concentrated winding is applied to a 6-slot/4-pole (6/4) SynRM, it has been found that its torque density
and efficiency as well as thermal characteristics can be effectively improved [12]. For the DSRMs, both
the short-pitched (SP) concentrated windings and the FP distributed windings can be employed and this
has been well investigated in literature [5], [13]. It has been found that the DSRM equipped with DL
mutually coupled (DLMC) winding, which is also a SP winding, is less sensitive to magnetic saturation
than the ones equipped with the DL conventional (DLC) windings and hence, produce higher average
torque at high phase current [5]. However, the torque ripple coefficient of the DSRM equipped with the
DLMC windings is relatively higher due to its nature of self- and mutual-inductances [14]. The FP
distributed winding DSRM can generate lower torque ripple but its long end-winding will result in
higher copper loss for a given phase current. In order to take advantage of both the FP distributed
windings (higher torque capability) and the SP concentrated windings (shorter end-winding), single
layer (SL) concentrated windings (SLC and SLMC) DSRMs have been proposed in [5]. They can have
higher torque capability than the DL concentrated windings (DLC and DLMC) counterparts but lower
copper loss than that of the FP distributed windings.
Although the rotor of the DSRM is simpler and easier for manufacturing than that of the SynRM,
the doubly salient (DS) rotor structure will result in high levels of acoustic noise and vibration [15]-[16].
In contrast, most SynRMs have non-salient rotors with various topologies in order to increase the
saliency ratio and also the difference between d- and q-axis inductances, and hence to increase the
torque capability [1], [2]. It is well established in literature that the SynRMs are generally designed with
transversally laminated rotor [17], [12]. Although the axially laminated rotor has advantages such as
increased saliency ratio, hence improved power density and power factor [18]-[19], it is very complex
for industrial manufacturing. Therefore, the transversally laminated rotor has been selected for
investigation in this paper. By way of example, rotors with 4 poles are illustrated and they generally
have two shapes, e.g. round flux barrier (RFB) and angled flux barrier (AFB) [17], [20]-[21]. The latter
is also used for some permanent magnet assisted SynRMs as shown in [22]-[23]. It has been found in
[18] that with the distributed windings, the three flux barrier layers SynRM can produce similar average
3
torque but lower torque ripple than other numbers of flux barrier layer. In addition, the influence of slot
numbers on the average torque is very minor but lower torque ripple can be produced with higher slot
numbers. Hence, the three-layer flux-barrier in the rotor will be adopted for the 12/4 and 12/8 machines
in this paper.
For clarity, a diagram including rotor topologies, slot/pole number combinations and winding
configurations for all the investigated reluctance machines in this paper is shown in Fig. 1. The three
rotor topologies: SynRM-RFBs, SynRM-AFBs and DSRM will be investigated for both the 12/4 and
12/8 slot/pole number combinations. In addition, the DL and SL conventional windings (DLC and SLC),
the DL and SL mutually-coupled windings (DLMC and SLMC), as well as the FP winding will be
employed and are illustrated in Fig. 1. By way of example, the d- and q-axis inductances and power
factors will be investigated on 12/8 machines with different windings and rotor topologies. For the
performance investigations throughout this paper, appropriate rotor structures will be identified based
on torque comparison at both low and high current levels for both the 12/4 and 12/8 machines. Then,
comparison in terms of average torque, torque ripple, copper loss and iron loss will be carried out by 2-
D finite element analysis (FEA) between different slot/pole number combinations and winding
configurations for the machines with appropriate rotor topologies.
Fig. 1. Investigated reluctance machines in this paper with different winding configurations and rotor topologies.
2. Features of Reluctance Machines
2.1. Different Rotor Topologies and Winding Configurations
For fairer comparison throughout this paper, machines with different windings and rotor
topologies have been optimized separately, and the optimization objective is to achieve the highest
torque for constant copper loss (Only dc losses have been considered, the end-winding has also been
included in copper loss calculations). It is worth mentioning that for the concentrated windings, only the
4
SL windings have been selected for optimization mainly because they can generally produce higher
average torque than their DL counterparts. Hence, the dimensions of stator core are kept the same for all
the winding configurations. However, the stator core has been optimized separately for machines with
different rotor structure. The main dimensions of all investigated machines are kept the same as shown
in Table 1. The rib width is 0.3mm for all SynRMs. However, the stator inner radii for 12/8 SynRM-
RFB, SynRM-AFB, and DSRM are optimized as 27mm, 27mm and 28.4mm, and the shaft outer radii
are 13mm, 9mm and 11.6mm, respectively.
Table 1 General dimensions and design parameters of reluctance machines
Stator slot number 12 Active length (mm) 60 Rotor pole number 4/8 Number of turns per phase 132 Stator outer radius (mm) 45 Slot area (mm態) 116 Air gap length (mm) 0.5 Current density (畦追陳鎚【mm態) 5.68
As mentioned previously, the SynRMs with three-layer flux-barrier in the rotor have been selected
for investigation in this paper. By way of example, the flux line distribution of the optimized 12/8
SynRMs with both round and angled flux-barrier rotors and different winding configurations, as well as
the 12/8 DSRM are shown in Fig. 2. Phase A is supplied with a 10A dc current and the rotor pole is
aligned with the phase A. It can be found that there is no flux through the phase B and the phase C for
the conventional concentrated windings as shown in Fig. 2a. However, the mutual fluxes present in both
the MC winding (Fig. 2b) and the FP windings (Fig. 2c).
a b c Fig. 2. Flux line distributions of 12/8 reluctance machines with different rotor topologies and winding configurations. The rotor pole is at the aligned position with the phase A, which is supplied with a 10A current. a SynRM with RFBs and SLC winding b SynRM with AFBs and DLMC winding c DSRM with FP winding
The material M330-35A is used for the prototype machines, which has a yield stress of 300MPa
and a material density of ばはのど倦訣【兼戴. By using 2D FEA, the maximum speed of 19000 rpm and
mechanical stress of 295MPa for the 8-pole SynRM rotor with AFBs have been obtained. However, 8-
pole SynRM rotor with RFBs and DSRM rotor can achieve much higher speed, i.e. 26000 rpm and
5
47000 rpm, respectively. Fig. 3 shows the comparison of mechanical stress 購 and radial displacement u
between different rotors at 19000 rpm. It is found that at this speed, the displacements of the rotor into
air-gap are lower than 1.84% of the air gap length (0.5mm). This means that the rotor will not rub the
stator inner surface at this operating speed.
a b c
Fig. 3. Mechanical stress 購 and radial displacement u comparison between different 8-pole rotors at 19000 rpm. a SynRM with RFBs b SynRM with AFBs c DSRM
Accordingly, coil magnetic polarities for different winding configurations are illustrated in Table
2. It can be found that the coil magnetic polarities of the SLC and SLMC machines are similar to those
of the DLC and DLMC machines, respectively. However, compared with the DL machines, the SL
machines have half number of coils per phase under the condition that the number of turns per phase
(132) is the same for both the DL and SL machines. Similar to the SL windings, the FP windings have
only two coils per phase but each coil spans three stator slot pitches due to the distributed winding
configuration as shown in Fig. 1. This will lead to longer end-winding, hence potentially higher copper
loss than other winding configurations for the same phase RMS current.
Table 2 Coil magnetic polarities of reluctance machines with different winding configurations
Winding configurations Coil magnetic polarities
Concentrated winding
SL winding SLC NSNSNS
SLMC NNNNNN
DL winding DLC SNSNSNSNSNSN
DLMC SSSSSSSSSSSS
Distributed winding FP winding FP NSNSNS
2.2. Influence of Rotor Topologies and Winding Configurations on d- and q-Axis Inductances and Power Factors
Since the DSRMs are supplied with 3-phase sinewave currents and in effect become SynRMs but
with salient rotors, the phasor diagram of the SynRMs can be applicable to the DSRMs as well.
Accordingly, accounting for the cross-couplings, the d- and q-axis inductances 詣鳥 and 詣槌 are described
by
6
詣鳥盤件鳥 ┸ 件槌匪 噺 閤鳥盤件鳥 ┸ 件槌匪件鳥 (1) 詣槌盤件鳥 ┸ 件槌匪 噺 閤槌盤件鳥 ┸ 件槌匪件槌 (2)
where 閤鳥 and 閤槌 are the d- and q-axis stator flux linkages, 件鳥 and 件槌 are the d- and q-axis stator
currents, respectively. By way of example, the 12/8 machines have been selected to investigate the
influence of rotor topologies and winding configurations on the d- and q-axis inductances. Table 3
compares 詣鳥 and 詣槌 of the 12/8 machine topologies with different rotor topologies and winding
configurations. It can be found that the machines with the FP winding has the highest 詣鳥 and 詣槌 at など畦追陳鎚 than others, regardless of rotor topologies. This will become an important factor that limits the
constant power speed range. Additionally, the SL winding machines have higher 詣鳥 and 詣槌 than their
DL counterparts. The saliency ratio 岫耕 噺 挑匂挑忍岻 in Table 4 shows that the machines with the DLMC
winding have the highest 耕, regardless of the rotor structures. Therefore, it can be predicted that the 12/8
machines with the DLMC winding could have better performance than others due to their highest
saliency ratio. Furthermore, the power factors (see Table 4) can be obtained according to the phasor
diagram of synchronous reluctance machines. It can be found that the SynRM-RFB can have the highest
saliency ratio and power factors, regardless of winding configurations. Moreover, the power factors of
the machines with DL windings are higher than that of the machines with SL windings. The machines
with FP windings have the lowest power factors.
Table 3 Comparison of d- and q-axis inductances between different 12/8 machines at 層宋冊司仕史 (薩纂 噺 薩刺岻
鯖袈 (mH) 鯖恵(mH)
SynRM-RFB SynRM-AFB DSRM SynRM-RFB SynRM-AFB DSRM SLC 6.9 7.3 7.7 3.9 4.5 4.7
SLMC 7.1 7.7 9.0 3.9 4.5 4.9 FP 11.9 9.9 14.1 7.8 8.7 8.4
DLC 3.5 3.2 4.8 2.4 2.8 2.7 DLMC 4.4 5.4 5.0 2.1 2.6 2.6
Table 4 Comparison of saliency ratio 鯖袈鯖恵 and power factors for different 12/8 machines at 層宋冊司仕史 (薩纂 噺 薩刺岻
SynRM-RFB SynRM-AFB DSRM 詣辰【詣単 Power Factor 詣辰【詣単 Power Factor 詣辰【詣単 Power Factor
SLC 1.787 0.676 1.639 0.638 1.635 0.621
SLMC 1.847 0.679 1.713 0.637 1.834 0.620
FP 1.523 0.576 1.135 0.508 1.680 0.567
DLC 1.459 0.778 1.122 0.741 1.787 0.745 DLMC 2.106 0.796 2.096 0.752 1.895 0.750
It is established that the electromagnetic torque performance can be determined by the difference
between 詣鳥 and 詣槌 . Hence, (詣鳥 伐 詣槌 ) has been calculated with different winding configurations as
7
shown in Fig. 4. Also, the 岫宅凍宅桃 伐 な岻 of DSRMs has been shown in Fig. 4d. It is apparent that at low
current, the highest (詣鳥 伐 詣槌) of the SynRM-RFB and the DSRM are achieved by using the FP winding.
However, for the SynRM-AFB, this can be obtained by using the SLMC winding. Therefore, at low
current, the 12/8 FP-SynRM RFB and FP-DSRM can be predicted to produce higher torque than other
12/8 SynRM-RFBs and DSRMs, respectively. However, at high current, the DLMC winding produces
the highest (詣鳥 伐 詣槌), regardless of rotor topologies. Hence, it could be predicted that all the three 12/8
machine topologies can achieve their best torque performances at high current levels when the DLMC
winding configuration is employed. Moreover, the 12/8 DLMC-DSRM could potentially generate
higher torque than the 12/8 DLMC-SynRMs due to slightly higher (詣鳥 伐 詣槌).
a b
c d
Fig. 4. Comparison of 岫詣鳥 伐 詣槌岻 and 岫挑匂挑忍 伐 な岻 against phase RMS current between 12/8 reluctance machines. The machines
are supplied with 3-phase sinewave currents with 荊鳥 噺 荊槌. a 岫詣鳥 伐 詣槌岻 of SynRM with RFBs b 岫詣鳥 伐 詣槌岻 of SynRM with AFBs c 岫詣鳥 伐 詣槌岻 of DSRM
d 岫挑匂挑忍 伐 な岻 of DSRM
3. Torque Performances for Different Windings, Rotor Topologies and Pole Numbers
3.1. Influence of Rotor Topologies on Torque Performances for both the 12/4 and 12/8 Machines
According to the d- and q-axis inductances, the electromagnetic torque of a 3-phase reluctance
machine can be calculated by
劇 噺 ぬに 抜 喧盤詣鳥 伐 詣槌匪荊鳥荊槌 噺 ぬね 抜 喧盤詣鳥 伐 詣槌匪荊嫌に sin ゎ (3)
8
where 喧 is the pole pair number, 糠 is the current phase angle, and 荊鎚 is the phase peak current,
respectively. It is apparent that the maximum average torque will be obtained at 糠 噺 ねのソ (荊鳥 噺 荊槌 )
without considering magnetic saturation [1], [20]. For completeness, average torques at different current
levels of all the 12/4 and 12/8 machines have been obtained by 2D-FEA, as shown in Fig. 5. The torque
ripple coefficient is calculated by 劇追沈椎椎鎮勅 噺 脹尿尼猫貸脹尿日韮脹尼寧 抜 などどガ, where 劇陳銚掴, 劇陳沈津 and 劇銚塚 are the maximum,
minimum and average torques over one electrical cycle. It is worth noting that with different pole
numbers and winding configurations, the reluctance will be different due to different winding factors
and airgap permeances. Hence, their influence on torque performances will be investigated separately in
the following sections.
a b
c d
Fig. 5. Torque performance of the 12/4 and 12/8 SynRMs and DSRMs with different winding configurations at (i) 10 Arms and (ii) 40 Arms. a Average torque of 12/4 machines b Torque ripple coefficient 12/4 machines c Average torque of 12/8 machines d Torque ripple coefficient of 12/8 machines
It can be found that for the SynRMs, the RFB rotor can produce higher average torque than the
AFB rotor due to 20% higher average ratio of flux barrier thickness to the combined thickness of
lamination and flux barrier, hence higher 鯖袈鯖恵 [1] . This is true for almost all winding configurations and
for both low and high current levels (except the 12/4 SLC winding at high current and the 12/8 DLMC
winding). However, the 12/4 and 12/8 DSRMs can produce similar or even higher average torque than
9
the SynRMs at both low and high current levels, regardless of winding configurations. The SynRMs
with AFB rotor produce higher torque ripple than the DSRMs and the SynRMs with RFB rotor for most
winding configurations. However, with similar average torque, the AFB rotor can produce lower torque
ripple at 12% for the 12/8 SLC winding at low current. Accordingly, the appropriate rotor topologies to
obtain the maximum average torque for both the 12/4 and 12/8 machines with different winding
configurations have been summarized in Table 5. For clarity, only the most appropriate rotor topologies
have been selected for further investigations.
Table 5 Appropriate rotor topologies to obtain the maximum average torque
Slot/pole combinations
Winding configurations SLC SLMC FP DLC DLMC
12/4 DSRM DSRM DSRM SynRM-RFB
&DSRM DSRM
12/8 SynRM-RFB
&DSRM DSRM DSRM DSRM
SynRM-AFB &DSRM
3.2. Influence of Slot/Pole Number Combinations on Torque Performance with Appropriate Rotor Topologies
With the appropriate rotor topologies such as the ones shown in Table 5, the influence of slot/pole
number combinations on torque-speed characteristics under I鱈叩淡 噺 なね┻なねA and �辰達 噺 などど� is shown
in Fig. 6.
a b
Fig. 6. Torque-speed curves between 12/4 and 12/8 machines with different windings. 荊陳銚掴 噺 なね┻なね畦 and 撃鳥頂 噺 などど撃. a 12/4 machines b 12/8 machines
It can be found that both the 12/4 and 12/8 machines with the FP windings and the doubly salient
rotors can achieve their best initial torques at など畦追陳鎚. However, the 12/4 machines can have wider
constant torque range than the 12/8 machines. In addition, it is also found that the DL machines can
have higher base speed than other machines. However, the FP machines have the highest initial torque
but the lowest base speed under the limit of 荊兼欠捲 噺 なね┻なねA and 撃穴潔 噺 などど�. It is worth mentioning that
the 4-pole machines would produce less iron losses due to lower electrical frequency than the 8-pole
machines. This will be investigated in the following section.
10
4. Influence of Machine Topologies on Copper Loss and Iron Loss
It is well-established that the copper loss (proportional to current squared) could be the dominant
loss for high torque low speed applications, while the iron loss could be the dominant loss for high
speed applications, where the iron losses are determined by the iron core flux density and also the
electrical frequency. Therefore, the aforementioned influence of winding and rotor topologies on torque
performance will also be reflected into the machine losses.
4.1. Copper Loss
Due to different end-windings, the winding configurations will have significant influence on the
copper loss characteristics. However, if phase current is unchanged then the different rotor pole
numbers and rotor topologies will have no influence on copper loss for the same sized machines. Due to
longer end-windings, the FP machines will generally produce higher copper loss than other machines,
regardless of current levels. At など畦追陳鎚, the copper loss of the FP (246W) can be around 1.5 times
higher than that of the SL (173W) and DL (154W) winding machines.
Although the FP machines generate higher copper loss than the SL and DL winding machines, the
average torque against copper loss characteristics could be more important for investigation because the
FP machines could generate higher average torque as well, as investigated previously. With appropriate
rotor topologies, both average torque and torque ripple against copper loss for machines with different
winding configurations have been obtained, as shown in Fig. 7. At lower torque level, e.g. 4Nm, both
the 12/4 and 12/8 FP-DSRM will produce lower copper loss. At high torque level, e.g. 6Nm, the 12/4
machine with the FP winding still have the best torque against copper loss performance than others.
However, for the 12/8 machines, the copper loss of the DLMC winding is about one-half of the 12/8 FP
winding machine at 10Nm. Moreover, the 12/8 DLMC machine exhibits even higher average torque at
high currents. This is due to the fact that the machines with the DLMC windings have lower mmf
concentration in the stator yoke, hence are less sensitive to the magnetic saturation. Nevertheless, they
exhibit higher torque ripple than the FP winding machines due to their nature of self- and mutual-
inductances as mentioned previously. It is also found that with appropriate winding configurations, the
torque capability of the 12/4 machines is similar to that of the 12/8 machines. Overall, it can be
concluded that with the FP windings, both the 12/4 and 12/8 machines can have better torque against
copper loss characteristics without heavy magnetic saturation. However, the 12/8 DLMC machines can
have better performance at high current levels (high copper loss).
11
a b
c d
Fig. 7. Influence of slot/pole number combinations and winding configurations on average torque and torque ripple against copper loss. a Average torque against copper loss of 12/4 machines
b Torque ripple against copper loss of 12/4 machines
c Average torque against copper loss of 12/8 machines
d Torque ripple against copper loss of 12/8 machines
4.2. Iron Loss
Different from copper loss, the iron loss can be influenced not only by the winding configurations,
but also by the slot/pole number combinations and rotor topologies. Considering the torque performance,
the FP and SLMC windings are selected for the 12/4 machines, whilst the FP and DLMC windings are
selected for the 12/8 machines. Moreover, both the DSRM and SynRM rotors are selected for iron loss
investigation. The iron loss density over one electrical cycle is comprised of hysteresis loss and eddy-
current loss, which can be calculated as [24]:
喧沈追墜津 岫激【兼戴岻 噺 血盤倦朕怠ッ稽椎椎 髪 倦朕態ッ稽椎椎態匪 髪 倦勅血 豹 岫項稽項建 岻態穴建怠【捗待 (4)
Where 血 is the stator or rotor flux density frequency, 稽椎椎 is the peak-to-peak flux density. For the
silicon iron cores considered in these machines, the hysteresis loss coefficients 倦朕怠 and 倦朕態 are の畦【兼
and ねど畦【兼, and the eddy current loss coefficient 倦勅 is ど┻どにに 畦兼【撃┻ The total iron loss is obtained by the summation of the iron losses calculated in every individual
FE mesh element in both the stator and the rotor. According to (4), it is necessary to investigate the
radial and tangential flux densities (稽堅 and 稽建) frequencies and their variations for both the stator and
the rotor, as shown in Table 6. It is worth noting that the rotor topology does not have any influence on
the flux density frequencies.
12
Table 6 Flux density frequencies of the stator and the rotor
Slot/pole combination Winding configuration Stator 稽追【稽痛 frequency (Hz) Rotor 稽追【稽痛 frequency (Hz)
12/4 FP なぬ┻ぬ 80
SLMC なぬ┻ぬ 40
12/8 FP には┻は 40
DLMC には┻は 80
It can be found that the stator flux density frequency is only influenced by the slot/pole number
combination and it is equal to 喧よ【はど┸ where 硬 is the mechanical rotor speed, and 喧 is the pole-pair
number. This means that the stator flux density has 1 period in every electrical cycle. Nevertheless, the
rotor flux density will present different frequencies due to different winding configurations and rotor
pole numbers.
By way of example, the 12/8 FP and 12/8 DLMC machines have been shown in Table 7 for
investigation on the stator and rotor iron losses at など 畦追陳鎚, 400 rpm. It can be found that, with the same
stator and rotor flux density frequencies, the SynRM-AFB generates higher stator and rotor iron loss
than the DSRM with 12/8 DLMC windings due to higher variations in 稽追 and 稽痛 . However, the
SynRM-RFB will generate lower stator and rotor iron loss than the DSRM with 12/8 FP windings due
to lower variations in 稽追 and 稽痛.
Table 7 Iron loss of 12/8 machines at 層宋寓慶型慧 and 400 rpm
Machines Iron loss (W)
Stator Rotor total 12/8 FP-SynRM RFB 1.79 1.86 3.65
12/8 FP-DSRM 2.24 2.45 4.69 12/8 DLMC-SynRM AFB 0.59 1.03 1.63
12/8 DLMC-DSRM 0.57 0.24 0.81
According to the torque capability, two rotor topologies have been selected for the 12/4 and 12/8
machines with appropriate winding configurations. For completeness, the influences of phase RMS
current and speed on total iron loss have been calculated, as shown in Fig. 8. It can be found that for the
12/4 machines, the SynRM-RFB with FP winding can produce the lowest iron losses for the full speed
and current ranges. However, for the 12/8 machines, the DSRM with DLMC winding produces the
lowest iron losses for the full speed and current ranges. Moreover, it is found that the 12/8 machines
have higher iron loss than the 12/4 machines with the same rotor topologies and windings at variable
current levels and speeds, as expected.
13
a b
c d
Fig. 8. Iron loss of selected 12/4 and 12/8 machines under different operating conditions. a 12/4 machines at 400 rpm with increasing phase RMS current b 12/4 machines at 10Arms with increasing speed c 12/8 machines at 400 rpm with increasing phase RMS current d 12/8 machines at 10Arms with increasing speed
5. Experimental Validation
In order to validate the predictions, both the 12/8 SL-DSRMs and the 12/8 DL-DSRMs that have
been built in [5] are employed in this paper, and the inductances and static torques have been measured
as detailed in the following sections. The FP winding has not been built due to its significantly longer
end-winding than other winding configurations, leading to higher copper loss. In addition, it has
relatively lower power factor.
The self- and mutual-inductances of the 12/8 DSRMs with different windings are measured
against rotor positions at 1A dc current as shown in Fig. 9. The measured phase resistances of the SL-
and DL-DSRMs are 1.48よ and 1.32 よ, respectively. The method of static torque measurement in [25]
has been adopted for undertaking the torque measurements in this paper. In order to measure the static
torque, three phases of the DSRMs are supplied with dc currents such as 荊凋 噺 荊, 荊喋 噺 荊寵 噺 伐な【に荊,
where 荊 is variable and controllable by the power supply. The static torques against rotor positions for
variable currents have been measured as shown in Fig. 10. It can be found that the measured results are
in good agreement with the predicted results.
14
a b
Fig. 9. Measurement of self- and mutual-inductances of 12/8 DSRMs with different windings at 1A dc current. a 12/8 conventional winding DSRMs
b 12/8 mutually-coupled winding DSRMs
a b
c d
Fig. 10. Static torque against rotor position for variable currents (solid line: predicted results, dot: measured results) a 12/8 DLC-DSRM b 12/8 DLMC-DSRM c 12/8 SLC-DSRM d 12/8 SLMC-DSRM
Furthermore, the machine efficiency has been obtained for both the 12/8 SL- and DL-DSRMs as
shown in Table 8 where the dc link voltage is 18V and the maximum phase peak current is 6A, which is
limited by the load-torque capacity of the used dc machine. The low efficiency is mainly due to the fact
that for the prototype machines, smaller copper wires have been used to ease the winding process,
leading to smaller slot filling factor and higher copper loss. The difference between predicted and
measured results is mainly because the end-winding effect has not been taken into account in the 2-D
FEA. In addition, the torque-sensor accuracy and measuring error can be the other factors that
contribute to this discrepancy.
Table 8 Machine efficiency (%) of 12/8 SL- and DL-DSRMs at 層宋寓慶型慧 and 400 rpm
15
Speed(rpm) DLC-DSRM DLMC-DSRM SLC-DSRM SLMC-DSRM
Predicted Measured Predicted Measured Predicted Measured Predicted Measured 350 21.24 16.86 22.37 17.97 31.71 24.67 32 26.2 400 23.56 20.30 24.77 21.83 34.67 28.31 34.98 30.56 450 25.74 22.34 27.03 24.55 35.89 27.19 36.73 29.85 500 27.81 23.43 29.16 25.57 37.36 30.61 37.22 30.84 550 29.76 24.24 31.17 25.64 39.35 31.02 39.18 33.83 600 31.61 26.9 33.06 27.37 41.11 -- 41.36 --
6. Conclusion
Three rotor topologies (SynRM-RFB, SynRM-AFB, and DSRM), five winding configurations
(SLC, SLMC, FP, DLC, DLMC) and two slot/pole number combinations (12/4 and 12/8) are employed
for investigation on the synchronous reluctance machines. By way of examples, the 12/8 SynRM-RFB
can produce the highest power factors regardless of winding configurations. In addition, the power
factors of DL windings are higher than both the SL and FP windings. The appropriate rotor topologies
have been identified for each winding configuration and slot/pole number combination, according to the
torque performance at different current levels. With appropriate rotor topology, the influence of
slot/pole number combinations on average torque and torque ripple for different phase currents have
been investigated. It has been found that the 12/4 and 12/8 machines have similar torque capability
(12Nm at 40Arms) when the appropriate winding configurations are employed. By way of example, the
FP winding is the most appropriate winding configuration for the 12/4 machines, while the DLMC
winding is the best for the 12/8 machines.
Regarding the copper loss, the FP winding presents the best average torque against copper loss
characteristics at low current for both the 12/4 and 12/8 machines. However, the 12/8 machines with the
DLMC winding achieve better average torque against copper loss at high current due to their shorter
end-windings. The investigation on iron loss shows that lower iron loss can be achieved by the SynRM-
RFBs rotor topology when compared to the DSRMs. Moreover, the FP and DLMC windings can
produce lower iron loss than other windings for the 12/4 and 12/8 machines, respectively.
7. Reference
[1] Staton D. A., Miller T. J. E. , Wood S. E., 'Maximising the saliency ratio of the synchronous reluctance motor', Proc. Inst. Elect. Eng. -Elect. Power Appl., 1993, 140, (4), pp. 249-259.
[2] Matsuo T. , Lipo T. A., 'Rotor design optimization of synchronous reluctance machine', IEEE Trans. Energy Convers., 1994, 9, (2), pp. 359-365.
[3] Miller T. J. E., 'Optimal design of switched reluctance motors', IEEE Trans. Ind. Electron., 2002, 49, (1), pp. 15-27.
[4] Lipo T. A., "Synchronous reluctance machines- a viable alternative for AC drives," presented at the Proc. Wisconsin Elect. Mach. Power Electron. Consortium, Madison, USA, 1991.
[5] Ma X. Y., Li G. J., Jewell G. W., Zhu Z. Q. , Zhan H. L., 'Performance comparison of doubly salient reluctance machine topologies supplied by sinewave currents', IEEE Trans. Ind. Electron., 2016, 63, (7), pp. 4086-4096.
16
[6] Liang X., Li G., Ojeda J., Gabsi M. , Ren Z., 'Comparative study of classical and mutually coupled switched reluctance motors using multiphysics finite-element modeling', IEEE Trans. Ind. Electron., 2014, 61, (9), pp. 5066-5074.
[7] Ojeda X., Mininger X., Gabsi M. , Lecrivain M., 'Sinusoidal feeding for switched reluctance machine: application to vibration damping', ICEM, 2008, pp. 1-4.
[8] Moghaddam R. R. , Gyllensten F., 'Novel high-performance SynRM designmethod: an easy approach for a complicated rotor topology', IEEE Trans. Ind. Electron., 2014, 61, (9), pp. 5058-5065.
[9] Reddy P. B., El-Refaie A. M., Huh K. K., Tangudu J. K. , Jahns T. M., 'Comparison of interior and surface PM machines equipped with fractional-slot concentrated windings for hybrid traction applications', IEEE Trans. Energy Convers., 2012, 27, (3), pp. 593-602.
[10] El-Refaie A. M., Jahns T. M. , Novotny D. W., 'Analysis of surface permanent magnet machines with fractional-slot concentrated windings', IEEE Trans. Energy Convers., 2006, 21, (1), pp. 34-43.
[11] El-Refaie A. M., 'Fractional-slot concentrated-windings synchronous permanent magnet machines: opportunities and challenges', IEEE Trans. Ind. Electron., 2010, 57, (1), pp. 107-121.
[12] Spargo C. M., Mecrow B. C., Widmer J. D. , Morton C., 'Application of fractional-slot concentrated windings to synchronous reluctance motors', IEEE Trans. Ind. Appl., 2015, 51, (2), pp. 1446-1455.
[13] Li G. J., Ma X. Y., Jewell G. W., Zhu Z. Q. , Xu P. L., 'Influence of conduction angles on single-layer switched reluctance machines', IEEE Trans. Magn., 2016, 52, (12), pp. 1-11.
[14] Li G. J., Ojeda J., Hlioui S., et al., 'Modification in rotor pole geometry of mutually coupled switched reluctance machine for torque ripple mitigating', IEEE Trans. Magn., 2012, 48, (6), pp. 2025-2034.
[15] Fiedler J. O., Kasper K. A. , Doncker R. W. D., 'Calculation of the acoustic noise spectrum of SRM using modal superposition', IEEE Trans. on Ind. Electron., 2010, 57, (9), pp. 2939-2945.
[16] Zhu Z. Q., Liu X. , Pan Z., 'Analytical model for predicting maximum reduction levels of vibration and noise in switched reluctance machine by active vibration cancellation', IEEE Trans. Energy Convers., 2011, 26, (1), pp. 36-45.
[17] Pellegrino G., Cupertino F. , Gerada C., 'Barriers shapes and minimum set of rotor parameters in the automated design of Synchronous Reluctance machines', Int. Conf. Electric Machines & Drives, 2013, pp. 1204-1210.
[18] Wang K., Zhu Z. Q., Ombach G., et al., 'Optimal slot/pole and flux-barrier layer number combinations for synchronous reluctance machines', Int. Conf. EVER, 2013, pp. 1-8.
[19] Kolehmainen J., 'Synchronous reluctance motor with form blocked rotor', IEEE Trans. Energy Convers., 2010, 25, (2), pp. 450-456.
[20] Moghaddam R. R., Magnussen F. , Sadarangani C., 'Theoretical and experimental reevaluation of synchronous reluctance machine', IEEE Trans. Ind. Electron., 2010, 57, (1), pp. 6-13.
[21] Vagati A., Pastorelli M., Francheschini G. , Petrache S. C., 'Design of low-torque-ripple synchronous reluctance motors', IEEE Trans. Ind. Appl., 1998, 34, (4), pp. 758-765.
[22] Bianchi N., Mahmoud H. , Bolognani S., 'Fast synthesis of permanent magnet assisted synchronous reluctance motors', IET Elec. Power Appl., 2016, 10, (5), pp. 312-318.
[23] Guan Y., Zhu Z. Q., Afinowi I. A. A., Mipo J. C. , Farah P., 'Design of synchronous reluctance and permanent magnet synchronous reluctance machines for electric vehicle application', ICEMS, 2014, pp. 1853-1859.
[24] Li G. J., Ojeda J., Hoang E., Lecrivain M. , Gabsi M., 'Comparative studies between classical and mutually coupled switched reluctance motors using thermal-electromagnetic analysis for driving cycles', IEEE Trans. Magn., 2011, 47, (4), pp. 839-847.
[25] Zhu Z. Q., 'A simple method for measuring cogging torque in permanent magnet machines', IEEE Power & Energy Society General Meeting, 2009, pp. 1-4.
Recommended