MCS-51 Guide - LEAP Electronic · MCS-51 Writer Unit back view Note DC 12V input socket Power...

MCS-51 Writer

Unit back view

Note

DC 12V input socket

Power switch USB port (B type)

MCS-51 Writer main unit x1, USB cable x1, adaptor x1, PC Software, drivers and manuals on CD-ROM x1

Introduction

Main unit USB cableDC 12V/500mA

Adaptor

Unit top view

1. It is preferred to use an internal USB port of your PC. External USB ports are not recommended because of shared bandwidth and possible compatibility issues of other USB devices.

2. Set Font Size to [small fonts] (96 dpi) to have the optimal display.

Textool handler

IC package diagram

Textool

MC

S-5

1 W

riter Illu

stra

tion

Devices Supported

ATMEL

HYUNDAI

INTEL

AT89C51AT89C52AT89LV51AT89LV52AT89C55AT89LV55AT89C51RCAT89C55WDAT89S51AT89S52AT89S53AT89LS51AT89LS52AT89LS53AT89S8252AT89LS8252

GMS97C51GMS97C52GMS97C54GMS97C56GMS97C58GMS97L51GMS97L52GMS97L54GMS97L56GMS97L58

87C51FA87C51FB87C51FC87C51RA87C51RB87C51RC87C5287C5487C58

ISSI

TEMIC

WINBOND

IS89C51IS89C52IS89C54IS89C58IS89C64IS89E54IS89E58IS89E64IS89LV51IS89LV52IS89C51AIS89C52AIS89LV51AIS89LV52A

TSC87C51TSC87C52

W77E58W77LE58W78E51W78E51BW78E52W78E52BW78E54W78E54BW78E58W78LE51W78LE52W78LE54W78E516W78E516BW78E62W78E62BW78LE516W78LE58

PHILIPS

SST

P89C51UBP89C52UBP89C54UBP89C58UBP89C51RA+P89C51RB+P89C51RC+P89C51RD+P89C51RB2HP89C51RC2HP89C51RD2HP89C51RA2P89C51RB2P89C51RC2P89C51RD2P89C51X2P89C52X2P89C54X2P89C58X2P89C51BP89C52BP89C54BP89C58BP89C660P89C662P89C664P89C668P89C138MBP89C238MBP89C838MB

SST89C54SST89C58SST89F54SST89F58

Install software and driver1. Set Font Size to [small fonts] (96 dpi) to have the optimal display. 1.1 Click the right button on the desktop. -> Select the [Properties] at the bottom of the function menu. 1.2 Select [Settings] and then click the [Advanced] to set Font Size.2. Install the software before connecting the MCS-51 Writer to the PC. 2.1 Insert the software CD into your CD-ROM drive. Normally the installation program will start automatically (if Auto Run is enabled for your CD-drive). Follow the instructions to complete installation. 2.2 If Auto Run doesn't work, click [Setup.exe] in the CD directory to start the installation.3. Install the driver for the MCS-51 Writer hardware. 3.1 Make sure the MCS-51 Writer power is [OFF]. Connect the power adapter to the MCS-51 Writer and a power outlet. 3.2 Connect the USB cable to PC USB port and to the programmer USB port. 3.3 Turn the MCS-51 Writer power to [ON]. Windows will now start the [Found New Hardware Wizard]. 3.4 Install Hardware Device Driver -> Search for a suitable driver for my device (recommended) 3.5 Select Optional search locations -> CD-ROM drives 3.6 Driver Files Search Result -> Windows will find a driver for this device ...\driver\flashwriter.inf 3.7 Click [Finish] in the Found New Hardware Wizard

The MCS-51 Writer software and drivers have now been installed and the unit is ready to work.

LEAP Electronic Co., Ltd.Tel : + 886-2-2999 1860Fax : + 886-2-2999 9873http : //www.leap.com.twEmail: service@leap.com.tw

[3.3] [3.4] [3.5]

[3.7][3.6]

MC

S-5

1 W

riter In

sta

llatio

n

8bits HEX display 16bits HEX display Buffer & file information

Source file editing

IC manufacturer, type number

Run

Stop

Device verifyCheck SUM

Programming status

Programming source

Select IC number

Load file

Save file

Operation window

Exit program

Load from PC Verify source IC

Read fromsource IC

Edit file

Save file

Erase Blank check

Program Verify Protect /security

Progress bar

Program process & options

Address of dataClick and enter new address.

ASCII code DisplayClick to enter text.

HEX code Display Click to enter hexadecimal data.

Exit edit window

Get data blockchecksum

Data block - FillData block -Move/Copy/Swap

Confirm changes

Cancel changes

Set data blockrange by load file size

Set data block range by maximum size of buffer

Set data blockrange by selected IC size

MC

S-5

1 W

riter O

pe

ratio

n