View
2
Download
0
Category
Preview:
Citation preview
www.ets-lindgren.com399807, Rev D
Warranty Information
For complete warranty information, see the user manual for your ETS-Lindgren antenna.
Mounting ETS-Lindgren Antennas
This guide describes the hardware required to mount your ETS-Lindgren antenna to a tripod, mast, or boom,
and is intended to be used in conjunction with the antenna user manual. This guide does not replace the
antenna user manual.
These antennas and mount destinations are included:
© Copyright 2008–2010 by ETS-Lindgren L.P. All Rights Reserved. No part of this document may be copied by any meanswithout written permission from ETS-Lindgren L.P.
The logo and are trademarks of ETS-Lindgren L.P.ETS-Lindgren BiConiLog
USA Headquarters1301 Arrow Point DriveCedar Park, TX 78613Phone: +1.512.531.6400support@ets-lindgren.com
Please see fwww.ets-lindgren.com or a list of all ETS-Lindgren offices.
WARRANTYONLY QUALIFIED PERSONNEL should install, operate, or service this equipment.
CONTACT ETS-LINDGREN PRIOR TO SERVICING. Servicing (or modifying) the unit by yourself may voidyour warranty. If you attempt to service the unit by yourself, disconnect all electrical power before starting.There are voltages at many points in the instrument that could, if contacted, cause personal injury.Only trained service personnel should perform adjustments and/or service procedures upon this instrument.Capacitors inside this instrument may still be CHARGED even when instrument is disconnected from its power source.
Safety Information
Before mounting an antenna, see .Safety Information For complete safety, regulatory, and
other product marking information, see the user manual for your ETS-Lindgren antenna.
BiConiLog Antennas –™ 3140B, 3149, 3142C, 3142D
Biconical Antennas –
Mini-Bicon Antennas –
Log Periodic Antennas –
Double-Ridged Waveguide Horns –
3164 Series Horns –
Pyramidal Horn Antennas –
Dipoles –
Loop Antennas and Rod Antennas –
Conical Log Spirals –
High Gain Conical Horns –
3109, 3104C, 3110B, 3110C
3180, 3181, 3182, 3183, 3184
3144, 3147, 3148, 3148B
3106B, 3115, 3116, 3117
Quad-Ridge Horns (–05, –06, –07, –08), Dual-Polarized Horns (–03, –04)
3160 Series, 3161 Series
3121C, 3121D
loop antennas, rod antennas
3101, 3102, 3103
3163 Series (–03, –04, –05, –06)
Antenna Type
Mount Destination
Revision/Date:
B, Updates–February, 2009
A, Initial Release–June, 2008 C, Added mini-bicons, 3301C–November, 2009
D, Updated 3149 mounting, added 3163–March, 2010
Model 4-TR Tripod –
Model
ETS-Lindgren 4-TR tripod
7-TR Tripod Positioner –
109042 –
106328 –
108197 –
108507 –
Mast –
2x2 Boom –
includes 109042, 106328, 108197, and 108507 booms:
straight; for general antenna mounting on a 7-TR
offset; for general antenna mounting on a 7-TR with pneumatic or manual polarization
center rotate; for rear-mount stinger-type antennas only
for the 3106 and 3106B only
2070 Series, 2075, and 2175 Antenna Towers
typical 2-inch by 2-inch boom; non-ETS-Lindgren and previous generation EMCO positioning systems
www.ets-lindgren.com
BiConiLog™ Antennas
3140B
7-TR refers to 109042, 106328,and 108197 booms:
Mast refers to 2070 Series, 2075,and 2175 Antenna Towers
2x2 Boom refers to a typical2-inch by 2-inch boom;non-ETS-Lindgren and previousgeneration EMCO positioning systems
– straight; for generalantenna mounting on a 7-TR
offset; for generalantenna mounting on a7-TR with pneumatic or manualpolarization
center rotate; forrear-mount stinger-typeantennas only
109042
106328
108197
–
–
Mounting ETS-Lindgren Antennas
4-TR: Do not mount toa 4-TR
7-TR: Mounts directly toa 7-TR without additionalhardware
Mast: Additional hardwarerequired to mount to a mast
Stinger Mounts4-TR
Do not mountto a 4-TR.
OR
7-TR, Mast 2x2 BoomNotes
Standard Parts
105861B Thread Insert(3140B ships with two)
100989 Polarizing Antenna Adapter(3140B ships with two)
Antennas shown here ship with thesestandard parts:
Antennas include mounting bracket(attached) and mounting knob(s)
101913Fixed
AntennaMount
105861BThreadInsert
100989 PolarizingAntenna Adapter
OR106470 Non-Polarizing
Antenna Adapter
Toantenna
mountingbracket,
insertknob
100989 PolarizingAntenna Adapter (2)
OR106470 Non-Polarizing
Antenna Adapter (2)
Toantenna
mountingbracket,
insertknob
104136Boom
AntennaMountKnob
(2)
Through boomon 7-TR, Mast
104169Boom
AntennaMountKnob
(2)
Through boomon 7-TR, Mast
105861BThread
Insert (2)
100989 PolarizingAntenna Adapter (2)
OR106470 Non-Polarizing
Antenna Adapter (2)
Toantenna
mountingbracket,
insertknob
Insert boom through
4-TR
OR OR
www.ets-lindgren.com
BiConiLog™ Antennas, continued
7-TR refers to 109042, 106328,and 108197 booms:
Mast refers to 2070 Series, 2075,and 2175 Antenna Towers
2x2 Boom refers to a typical2-inch by 2-inch boom;non-ETS-Lindgren and previousgeneration EMCO positioning systems
– straight; for generalantenna mounting on a 7-TR
offset; for generalantenna mounting on a7-TR with pneumatic or manualpolarization
center rotate; forrear-mount stinger-typeantennas only
109042
106328
108197
–
–
Mounting ETS-Lindgren Antennas
4-TR: Do not mount toa 4-TR
7-TR: Mounts directly toa 7-TR without additionalhardware
Mast: Additional hardwarerequired to mount to a mast
Stinger Mounts Notes
Standard Parts
105861B Thread Insert(3140B ships with two)
100989 Polarizing Antenna Adapter(3140B ships with two)
Antennas shown here ship with thesestandard parts:
Antennas include mounting bracket(attached) and mounting knob(s)
100989 PolarizingAntenna Adapter
OR106470 Non-Polarizing
Antenna Adapter
Toantenna
mountingbracket,
insertknob
104169Boom
AntennaMountKnob
105861BThreadInsert
Through boomon 7-TR, Mast
2x2 Boom
101913Fixed
AntennaMount
105861BThreadInsert
100989 PolarizingAntenna Adapter
OR106470 Non-Polarizing
Antenna Adapter
Toantenna
mountingbracket,
insertknob
3149, 3142D, 3142C
3149 101950Support Rod
101942BSupport
Base
To 4-TR
Toantenna
mountingbracket,
insertknob
100989Polarizing
Antenna Adapter
Toantenna
mountingbracket,
insertknob
105861BThread Insert
To 4-TR
105861BThread Insert
The 3149 can mount directly to a 4-TR.Use of a 102308 Swivel Antenna Mountsimplifies polarization, and is optional.
102308Swivel
AntennaMount
To 4-TR
100989 PolarizingAntenna Adapter
OR106470 Non-Polarizing
Antenna Adapter
Toantenna
mountingbracket,
insertknob
7-TR, Mast
OR100989 PolarizingAntenna Adapter
OR106470 Non-Polarizing
Antenna Adapter
Toantenna
mountingbracket,
insertknob
104136Boom
AntennaMountKnob
Through boomon 7-TR, Mast
3142C
3142D
Stinger
Stinger
Insert boom through
www.ets-lindgren.com
Biconical Antennas
3109
7-TR refers to 109042, 106328,and 108197 booms:
Mast refers to 2070 Series, 2075,and 2175 Antenna Towers
2x2 Boom refers to a typical2-inch by 2-inch boom;non-ETS-Lindgren and previousgeneration EMCO positioning systems
– straight; for generalantenna mounting on a 7-TR
offset; for generalantenna mounting on a7-TR with pneumatic or manualpolarization
center rotate; forrear-mount stinger-typeantennas only
109042
106328
108197
–
–
Mounting ETS-Lindgren Antennas
3109
3110C, 3110B, 3104C
3104C
3110B
3110C
4-TR: Do not mount toa 4-TR
7-TR: Mounts directly toa 7-TR without additionalhardware
Mast: Additional hardwarerequired to mount to a mast
Stinger Mounts
Standard Parts
100733 Support Rod
102108 Clamp Block
3110C, 3110B, and 3104C antennasship with these standard parts:
101942B Support Base
4-TR
OR OR
Notes4-TR
Can mount directly to a 4-TR.Use of a 102308 Swivel Antenna Mountsimplifies polarization, and is optional.
102308Swivel Antenna Mount
To 4-TR
Toantenna
mountinghole
7-TR, Mast
104169 Boom AntennaMount Knob
Through boomon 7-TR, Mast
Toantenna
mountinghole
2x2 Boom
106102 UniversalAntenna Mount
104136Boom
AntennaMountKnob
Through boom
Antennabalun
100733Support Rod
101942BSupport
Base
To 4-TR
102108Clamp Block
Antennashaft
Can mount directly to a 4-TR.Use of a 102308 Swivel Antenna Mountsimplifies polarization, and is optional.
102308Swivel
AntennaMount
To 4-TR
102108Clamp Block
Antennashaft
105861BThread Insert
To 4-TR
102108Clamp Block
Antennashaft
7-TR, Mast
OR
104169Boom
AntennaMountKnob
Through boomon 7-TR, Mast
102108Clamp Block
Antennashaft
105861BThread Insert
106102 UniversalAntenna Mount
104136Boom
AntennaMountKnob
Through boomon 7-TR, Mast
Antennabalun
2x2 Boom
OR
101913Fixed
AntennaMount
102108Clamp Block
Antennashaft
105861BThreadInsert
101937Swivel
AntennaMount
102108Clamp Block
Antennashaft
105861BThreadInsert
Stinger
Insert boom through Insert boom through
7-TR, Mast
www.ets-lindgren.com
Mini-Bicon Antennas
3109
7-TR refers to 109042, 106328,and 108197 booms:
Mast refers to 2070 Series, 2075,and 2175 Antenna Towers
2x2 Boom refers to a typical2-inch by 2-inch boom;non-ETS-Lindgren and previousgeneration EMCO positioning systems
– straight; for generalantenna mounting on a 7-TR
offset; for generalantenna mounting on a7-TR with pneumatic or manualpolarization
center rotate; forrear-mount stinger-typeantennas only
109042
106328
108197
–
–
Mounting ETS-Lindgren Antennas
3181, 3183, 3184Notes
3180, 3182
Stinger Mounts
4-TR: SeeAbout Mounts for3181/3183/3184
7-TR, Mast, 2x2 Boom:Additional hardwarerequired
3181, 3183, 3184
Mast: Additional hardwarerequired
3180, 3182
Standard Parts
4-TR / 7-TR: Mountsdirectly to a 4-TR or 7-TRwithout additional hardware
4-TR
OR OR
100733Support Rod
101942BSupport
Base
To 4-TR
102108Clamp Block
Stinger
Can mount directly to a 4-TR.Use of a 102308 Swivel Antenna Mountsimplifies polarization, and is optional.
102308Swivel
AntennaMount
To 4-TR
102108Clamp Block
Stinger
105861BThread Insert
To 4-TR
102108Clamp Block
Stinger
104169Boom
AntennaMountKnob
Through boomon 7-TR, Mast
102108Clamp Block
Stinger
105861BThread Insert
2x2 Boom
OR
Stinger
3180
3182
Stinger
101913Fixed
AntennaMount
102108Clamp Block
Stinger
105861BThreadInsert
Insert boom through
101937Swivel
AntennaMount
102108Clamp Block
105861BThreadInsert
Insert boom through
3181, 3183, and 3184 ship
with 113956 Antenna Mount
Assembly, which includes the
114669 Spacer; no additional
hardware required to mount
to 4-TR
About Mountsfor 3181/3183/3184
3180 and 3182 antennasship with these standard parts:
102108 Clamp Block
101942B Support Base
100733 Support Rod
Stinger
3181, 3184
3183
3180 withmini-cageelements 3180 with
solid conicalelements
Stinger
4-TR
113956 AntennaMount Assembly
To4-TR forverticalmount
To4-TR for
horizontalmount
(extensionoptional)
Stinger
2x2 Boom
113956 AntennaMount Assembly
101937Swivel
AntennaMount
Insert boom through
Stinger
For verticalmount
Forhorizontal
mount(extensionoptional)
7-TR, Mast
113956 AntennaMount Assembly
Stinger
104169Boom
AntennaMountKnob
Through boom
For verticalmount place
114669 spacerover extension
Forhorizontal
mount(extensionoptional)
Stinger
Standard Parts
www.ets-lindgren.com
Log Periodic Antennas
7-TR refers to 109042, 106328,and 108197 booms:
Mast refers to 2070 Series, 2075,and 2175 Antenna Towers
2x2 Boom refers to a typical2-inch by 2-inch boom;non-ETS-Lindgren and previousgeneration EMCO positioning systems
– straight; for generalantenna mounting on a 7-TR
offset; for generalantenna mounting on a7-TR with pneumatic or manualpolarization
center rotate; forrear-mount stinger-typeantennas only
109042
106328
108197
–
–
Mounting ETS-Lindgren Antennas
105861B Thread Insert
100989 Polarizing Antenna Adapter
Antennas shown here ship with thesestandard parts:
3148B
3148, 3147, 3144
4-TR: Do not mount toa 4-TR
7-TR: Mounts directly toa 7-TR without additionalhardware
Mast: Additional hardwarerequired to mount to a mast
Stinger Mounts Notes4-TR
OR OR100989Polarizing
Antenna Adapter
Toantenna
mountingbracket,
insertknob
105861BThreadInsert
To 4-TR
101950Support Rod
101942BSupport
Base
To 4-TR
Toantenna
mountingbracket,
insertknob
105861BThread Insert
Can mount directly to a 4-TR.Use of a 102308 Swivel Antenna Mountsimplifies polarization, and is optional.
102308Swivel
AntennaMount
To 4-TR
100989 PolarizingAntenna Adapter
OR106470 Non-Polarizing
Antenna Adapter
Toantenna
mountingbracket,
insertknob
Antennas include mounting bracket(attached) and mounting knob(s)
7-TR, Mast
OR
104136Boom
AntennaMountKnob
Through boomon 7-TR, Mast
100989 PolarizingAntenna Adapter
OR106470 Non-Polarizing
Antenna Adapter
Toantenna
mountingbracket,
insertknob
100989 PolarizingAntenna Adapter
OR106470 Non-Polarizing
Antenna Adapter
Toantenna
mountingbracket,
insertknob
104169Boom
AntennaMountKnob
105861BThreadInsert
Through boomon 7-TR, Mast
2x2 Boom
OR100989 PolarizingAntenna Adapter
OR106470 Non-Polarizing
Antenna Adapter
Toantenna
mountingbracket,
insertknob
101913Fixed
AntennaMount
100989 PolarizingAntenna Adapter
OR106470 Non-Polarizing
Antenna Adapter
Toantenna
mountingbracket,
insertknob
101937Swivel
AntennaMount
Stinger
Insert boom through Insert boom through
3147
3148
Notes7-TR, Mast
www.ets-lindgren.com
Double-Ridged Waveguide Horns
3115
3106B
3116
3117
4-TR
The 3115, 3116, and 3117mount directly to a 4-TR.
Mounting hardware isincluded; no additional
hardware required.
Do not mount the3106B to a 4-TR.
Mounting ETS-Lindgren Antennas
4-TR: Do not mount toa 4-TR
7-TR: Mounts directly toa 7-TR without additionalhardware
Mast: Additional hardwarerequired to mount to a mast
Stinger Mounts2x2 Boom
OR
2x2 Boom
104169Boom
AntennaMountKnob
Through boomon 7-TR, Mast
Toantenna
mountinghole
101913Fixed
AntennaMount
101937Swivel
AntennaMount
Toantenna
mountinghole
Toantenna
mountinghole
7-TR refers to these booms:
Mast refers to 2070 Series, 2075,and 2175 Antenna Towers
2x2 Boom refers to a typical2-inch by 2-inch boom;non-ETS-Lindgren and previousgeneration EMCO positioning systems
– straight; for generalantenna mounting on a 7-TR
offset; for generalantenna mounting on a7-TR with pneumatic or manualpolarization
center rotate; forrear-mount stinger-typeantennas only
109042
106328
108197
–
–
–c(for 3106/B only)enterline rotation boom;
when changing polarization,maintains centerline rotation
108507
Stinger
Insert boom through Insert boom through
Mounted onto 4-TR
MountE
xam
ple
Model 3106B
Mounted onto 7-TR
with 3106B centerline rotation boom
4-TR 7-TR, Mast 2x2 Boom
www.ets-lindgren.com
3164 Series Horns
7-TR refers to 109042, 106328,and 108197 booms:
Mast refers to 2070 Series, 2075,and 2175 Antenna Towers
2x2 Boom refers to a typical2-inch by 2-inch boom;non-ETS-Lindgren and previousgeneration EMCO positioning systems
– straight; for generalantenna mounting on a 7-TR
offset; for generalantenna mounting on a7-TR with pneumatic or manualpolarization
center rotate; forrear-mount stinger-typeantennas only
109042
106328
108197
–
–
Mounting ETS-Lindgren Antennas
Quad-Ridge Horns
3164-05, -06, -07, -082x2 Boom4-TR
Do not mount3164-06, -07, or -08antennas to a 4-TR.
See .About 3164 Mounts
7-TR, Mast
See .About 3164 Mounts See .About 3164 Mounts
Dual-Polarized Horns
3164-03, -04
Notes
Standard Parts
105861B Thread Insert–ships with3164-08
106974 Mount–ships with 3164-06and 3164-07
3164-05–ships withmounting hardware; noadditional hardware requiredto mount to 4-TR, 7-TR,mast, or 2x2 boom
106974 Mount–only for3164-03, -04, -06, and -07
112859 Mount–only for3164-08
About 3164 Mounts
OR
104136Boom
AntennaMountKnob
Through boomon 7-TR, Mast
Toantenna
mountinghole
106974 Mount
105861BThreadInsert
104169Boom
AntennaMountKnob
106974 or 112859Mount
Through boomon 7-TR, Mast
Toantenna
mountinghole
106974 or 112859Mount
105861BThreadInsert
101913Fixed
AntennaMount
Toantenna
mountinghole
105861BThreadInsert
106974 Mount
To 4-TR
Toantenna
mountinghole
106974 Mount
105861BThreadInsert
101913Fixed
AntennaMount
Toantenna
mountinghole
104136Boom
AntennaMountKnob
Through boomon 7-TR, Mast
Toantenna
mountinghole
106974 or 112859Mount
Insert boom through
Insert boom through
www.ets-lindgren.com
Pyramidal Horn Antennas
3160 Series, 3161 Series
4-TR: Do not mount large pyramidalhorn antennas to a 4-TR.
7-TR refers to 109042, 106328,and 108197 booms:
Mast refers to 2070 Series, 2075,and 2175 Antenna Towers
2x2 Boom refers to a typical2-inch by 2-inch boom;non-ETS-Lindgren and previousgeneration EMCO positioning systems
– straight; for generalantenna mounting on a 7-TR
offset; for generalantenna mounting on a7-TR with pneumatic or manualpolarization
center rotate; forrear-mount stinger-typeantennas only
109042
106328
108197
–
–
Notes
Mounting ETS-Lindgren Antennas
3160-09 3160-10–and shipwith a supplementalmount that may be usedwith the 4-TR, 7-TR, mast,and 2x2 boom
About 3160 Mounts7-TR, Mast
Pyramidal horn antennasmount directly to a 4-TR;no additional hardware
required.
Do not mount 3160-01,3160-02, and 3161-01antennas to a 4-TR.
See .About 3160 Mounts See .About 3160 MountsSee .About 3160 Mounts
4-TR 2x2 Boom
OR
2x2 Boom
104169Boom
AntennaMountKnob
Through boomon 7-TR, Mast
Toantenna
mountinghole
101913Fixed
AntennaMount
101937Swivel
AntennaMount
Toantenna
mountinghole
Toantenna
mountinghole
Insert boom through Insert boom through
4-TR
OR OR
Standard Parts
www.ets-lindgren.com
Dipoles
7-TR refers to 109042, 106328,and 108197 booms:
Mast refers to 2070 Series, 2075,and 2175 Antenna Towers
2x2 Boom refers to a typical2-inch by 2-inch boom;non-ETS-Lindgren and previousgeneration EMCO positioning systems
– straight; for generalantenna mounting on a 7-TR
offset; for generalantenna mounting on a7-TR with pneumatic or manualpolarization
center rotate; forrear-mount stinger-typeantennas only
109042
106328
108197
–
–
Mounting ETS-Lindgren Antennas
3121D
3121C
4-TR: Do not mount toa 4-TR
7-TR: Mounts directly toa 7-TR without additionalhardware
Mast: Additional hardwarerequired to mount to a mast
Stinger Mounts
100733 Support Rod
102108 Clamp Block
101942B Support Base
Antennas shown here ship with theseantenna adapters:
Notes
100733Support Rod
101942BSupport
Base
To 4-TR
102108Clamp Block
Antennashaft
Can mount directly to a 4-TR.Use of a 102308 Swivel Antenna Mountsimplifies polarization, and is optional.
102308Swivel
AntennaMount
To 4-TR
102108Clamp Block
Antennashaft
105861BThread Insert
To 4-TR
102108Clamp Block
Antennashaft
7-TR, Mast
OR
104169Boom
AntennaMountKnob
Through boomon 7-TR, Mast
102108Clamp Block
Antennashaft
105861BThread Insert
106102 UniversalAntenna Mount
104136Boom
AntennaMountKnob
Through boomon 7-TR, Mast
Antennabalun
2x2 Boom
OR
101913Fixed
AntennaMount
102108Clamp Block
Antennashaft
105861BThreadInsert
101937Swivel
AntennaMount
102108Clamp Block
Antennashaft
105861BThreadInsert
Stinger
Insert boom through Insert boom through
www.ets-lindgren.com
Loop Antennas and Rod Antennas
Loop Antennas
Rod Antennas
7-TR refers to 109042, 106328,and 108197 booms:
Mast refers to 2070 Series, 2075,and 2175 Antenna Towers
2x2 Boom refers to a typical2-inch by 2-inch boom;non-ETS-Lindgren and previousgeneration EMCO positioning systems
– straight; for generalantenna mounting on a 7-TR
offset; for generalantenna mounting on a7-TR with pneumatic or manualpolarization
center rotate; forrear-mount stinger-typeantennas only
109042
106328
108197
–
–
Mounting ETS-Lindgren Antennas
Notes7-TR, Mast4-TR
Loop antennas androd antennas mount
directly to a 4-TR;no additional hardware
required.
2x2 Boom
OR
2x2 Boom
104169Boom
AntennaMountKnob
Through boomon 7-TR, Mast
Toantenna
mountinghole
101913Fixed
AntennaMount
101937Swivel
AntennaMount
Toantenna
mountinghole
Toantenna
mountinghole
Insert boom through Insert boom through
MIL-STD-461F Kit–Tocomply with the standard,a cable and groundingkit (113359) is includedwith the 3301C.
4-TR Light Tripod–Tocomply with theMIL-STD-461F standard,a smaller tripod (4-TR,1ML)is available (optional).
About 3301C
See About 3301C3301C
Standard Parts
www.ets-lindgren.com
Conical Log Spirals
Conical log spiralsnot intended
for 2x2 boom.
3101
3102
3103
7-TR refers to 109042, 106328,and 108197 booms:
Mast refers to 2070 Series, 2075,and 2175 Antenna Towers
2x2 Boom refers to a typical2-inch by 2-inch boom;non-ETS-Lindgren and previousgeneration EMCO positioning systems
– straight; for generalantenna mounting on a 7-TR
offset; for generalantenna mounting on a7-TR with pneumatic or manualpolarization
center rotate; forrear-mount stinger-typeantennas only
109042
106328
108197
–
–
Conical log spiralsmount directly to a 7-TR.
Mounting hardware isincluded; no additional
hardware required.
Mounting ETS-Lindgren Antennas
Conical log spirals mountdirectly to a 4-TR;
no additional hardwarerequired.
101941 Support Rod–ships with3101
101943B Support Rod–ships with3102
101944 Support Rod–ships with3103
101942B Support Base–ships with3101, 3102, and 3103
Notes4-TR 7-TR, Mast 2x2 Boom
www.ets-lindgren.com
High Gain Conical Horns
7-TR refers to 109042, 106328,and 108197 booms:
Mast refers to 2070 Series, 2075,and 2175 Antenna Towers
2x2 Boom refers to a typical2-inch by 2-inch boom;non-ETS-Lindgren and previousgeneration EMCO positioning systems
– straight; for generalantenna mounting on a 7-TR
offset; for generalantenna mounting on a7-TR with pneumatic or manualpolarization
center rotate; forrear-mount stinger-typeantennas only
109042
106328
108197
–
–
Mounting ETS-Lindgren Antennas
Notes
Model 3163 Serieshorn antennas
mount directly to a 4-TR;no additional hardware
required.
4-TR 7-TR, Mast
104169Boom
AntennaMountKnob
Through boomon 7-TR, Mast
Toantenna
mountinghole
2x2 Boom
OR
2x2 Boom
101913Fixed
AntennaMount
101937Swivel
AntennaMount
Toantenna
mountinghole
Toantenna
mountinghole
Insert boom through Insert boom through
3163 Series
-03, -04, -05, -06
3163-03
3163-04
3163-05
3163-06
About 3163 Series
The backplate on each
Model 3163 Series provides
threaded holes for
mounting directly into the
feed section of
a tapered chamber.
Additionally, you can use
the threaded holes
to create your own custom
mounting solution. See the
3163 manual for a diagram
of each backplate.
Each Model 3163 Series
includes a built-in
1/4–20 thread mount.
www.ets-lindgren.com
Mount Examples
Mounting ETS-Lindgren Antennas
3181, 3184
Stinger-mounted
onto 4-TR tripod with the
113956 antenna mount assembly
Stinger-mounted onto a 4-TR tripod
with a 102108 clamp block
3180
Stinger-mounted onto 4-TR tripod
with a 102108 clamp block and 100733 support rod
(101942B support base not shown)
3182 3183
Stinger-mounted onto 4-TR tripod
with a 102108 clamp block
3301C
Mounted onto tripod
Recommended