Sherief Reda Division of Engineering, Brown University...

1

Physical Design of Digital Integrated Circuits(EN0291 S40)

Sherief RedaDivision of Engineering, Brown University

Fall 2006

2

• Static timing analysis• STA for sequential circuits • Delay modeling: devices and interconnects• Statistical static timing analysis

Lecture 04: Timing Analysis

3

Propagation delay definition

Logic block

time

voltagea y

propagation delay50%

Vmax(10)%

10% 90%

transitiontime

Definitions:

• rise/fall propagation delay

• rise/fall transition delay (slew (slope): ΔV/transition delay)

4

Problem: Given a circuit, find the path(s) with the largest delay (critical paths)

• Solution: run SPICE and report the results of the simulation

• Problem: SPICE is computationally expensive to run except for small-size circuits

• WANTED: We need a fast method that produces relatively accurate timing results compared to SPICE

5

Static timing analysis

1/2

2/4 3/5

1/22/4

2/3

1/2

I1I2I3I4

I5I6

O1

O2

C17 from ISCAS’85 benchmarks

All inputs are arrive at time 0

Assuming all interconnects have 0 delay

Each gate has rise/fall delay

1/2

2/4

1/2

7/7

6/4

9/10

9/11 In reality, each input pin has its own rise/fall delay and wires have delays

simplifiedanalysis

slack = arrival time – required arrival time⇒ paths with negative slacks need to be eliminated!

criticalpath

6

Finding the critical path through breadth first search

• Initialize queue Q to empty• for all vertices i in V: nvisit[i]=0; • Add all primary input vertices to queue Q• While (Q ≠ 0)

– i = top of Q; remove i from Q; computer delay of i– for every edge (i, j):

• nvisit[j]++;• if(nvisit[j] == fanin[j]) add j to Q

2/1

4/21/1

3/24/3

3/2

2/2

I1I2

I3I4

I5

I6

O1

O2

7

STA can lead to false critical paths

2×1MUX

delay = 5

delay = 3

delay = 5

delay = 3

2×1MUX

outa

b

0

1 1

0

• What is critical path delay according to STA?• Is this path realizable?

No, actual delay is less than estimated by STA

STA assumes a signal would propagate from a gate input to its output regardless of the values of other inputs

8

• Static timing analysis• STA for sequential circuits • Delay modeling: devices and interconnects• Statistical static timing analysis

Lecture 04: Timing Analysis

9

Timing analysis of sequential circuits

combinational circuit

input outputcycle time P

setuptime Ts

holdtime Th

[dmin .. dmax]

FF

clock

Δ

FF

clock

Δ

10

Timing analysis of sequential circuits under presence of clock skew

combinational circuit

input output

[dmin .. dmax]

FFj

clock

Δ

FFi

clock

Δ

T=0

si

sj

cycle time P

11

Sometimes introducing skew can be helpful

FFi FFjFFkdmax=8ns

dmax=10ns

si sj

Zero clock skew (si =0 & sj = 0) ⇒ clock period = 10ns, fmax = 100MHz

Si = -1 sj = 0 ⇒ clock period = 9ns, fmax = 111MHz (no timing violations)

Si = -2 sj = 0 ⇒ clock period = 8ns, fmax = 125MHz (no timing violations)

Introducing skew also helps minimize the simultaneous switching of FFs → less load on the P/G network

STA is relatively easy once we figure out how to calculate gate and interconnect delay

12

• Static timing analysis• STA for sequential circuits • Delay modeling: devices and interconnects• Statistical static timing analysis

Lecture 04: Timing Analysis

13

Elmore delay model: An upper bound to actual delay in RC trees

R1 R2 R3 RN

C1 C2 C3 CN

Sum the result of multiplying each resistance by the capacitance down stream from it

any tree structure

step input

[see Gupta/Pileggi’97 for more info]

What is the runtime complexity?

14

Switch-level device RC delay models

PMOS modelNMOS model

[source: Weste/Harris]

15

Modeling the delay of an inverter

Holes have half the mobility of electrons → PMOS width = 2× of the NMOS device to get the same current

(or resistance) during output rise→ equal rise and fall delays for CMOS inverter

loading affects gate delay

16

Gate delay: rise delay

6C

2C2

2

224hC

B

Ax

Y

h copies

R

(6+4h)CY ( )6 4pdrt h RC= +

AB

Y

Assumption: interconnect delay is ignored (for the moment)

step input

rise propagation delay

17

Gate delay: fall delay

h copies

fall delay is worse than rise delay in this case

AB

Y6C

2C2

2

224hC

B

Ax

Ystep input

(1)

( ) ( ) ( ) ( )( )

2 2 22 6 4

7 4

R R Rpdft C h C

h RC

= + + +⎡ ⎤⎣ ⎦= +

(6+4h)C2CR/2

R/2x Yfall propagation delay

18

Gate delay is input pattern dependant

h copies

AB

Y6C

2C2

2

224hC

B

Ax

Ystep input

(1)

fall propagation delay

⇒ Connect the latest arriving signal closest to the output node whenever feasible

19

Impact of transition time on gate delay

gateInput Output

Δ

Δ’

time

time

τi

In addition to capacitive load, input transition time affects • delay: τi > 0 → Δ’ > Δ• output transition time:

20

Why does transition time affect delay?

During transition, gate current < saturation current→ higher effective output resistance → larger delay∴ Input transition time affects gate delay (and output transition time too!)

GateΔr/f(C, τi)

total capacitance(intrinsic + loading + interconnects)

tiτi

Ti+Δr/fτostored in a lookup

table for fast calculation

21

Interconnect delay: the lumped case

0V

Vm Vout

Upper bound on delays in RC trees [Pileggi’97]

22

Interconnect delay: lumped vs. distributed

R1 R2 R3 RN

C1 C2 C3 CN

lumped overestimates

delay

r = resistance per unit length

c = capacitance per unit length

23

Carryout STA after annotating your circuit with gate/interconnect delays

• Annotate your circuit with gate/interconnect delay, and carry out STA

• Don’t ignore interconnect delay because it is currently responsible for ~80% of total path delays!

24

• Static timing analysis• STA for sequential circuits • Delay modeling: devices and interconnects• Statistical static timing analysis

Lecture 04: Timing Analysis

25

In Statistical STA (SSTA), delay is no longer deterministic

I1I2

I3I4

I5I6

O1

O2pd

f

delay

pdf

delay

pdf

delay?

Replace deterministic gate delay by a random delay variable thathas a normal pdf

What is the pdf of z = max(x, y), where x and y are two random normal variables?

z is not normal, but can be approximated reasonable using random variables [Jacobs/Berkelaar’00]

x

y

z

26

Gate variations impact critical path(s) delay leading to an increase in the average delay

• Intra-chip (within-die) variations: arises within devices in the same die

• Inter-chip (die-to-die) variations: arises between different chips

27

Assignments for next lecture

Reading assignments:• Statistical Timing Analysis for Intra-Die Process Variations with

Spatial Correlations, ICCAD'03 (Kundan + (Yiwen) (judge))• Incremental timing analysis, US Patent 5508937 (Cesare)• Industrial products:

– Cadence SignalStorm (Elif) – Synopsys PrimeTime (Brendan)

Projects overview:• 10-15 mins presentation on previous work + proposal

• 1½ → 2 page report