View
6
Download
0
Category
Preview:
Citation preview
One set required per drawer
15 Subject to technical modifications without notice. © 2006
TANDEM 552H partial extension drawer runners
Overlay application Description Basic components
- Partial extension concealed drawer runners - For 16 (5/8") max. drawer side thickness- Zinc coated steel profiles- Concealed roller carriages with permanently lubricated synthetic rollers create a smooth running action- Locking devices enable easy drawer insertion and removal- Force guided right side and ±1.5 (1/16") tolerance compensating left side- Dynamic weight capacity of 75 lb- Static weight capacity of 100 lb
Using TANDEM page 13
Other applications
Components
Profile set
For overall cabinet depth
Drawer length
Extensionloss TANDEM
305 (12") 229 (9") 37 (1-7/16") 552H2290N*381 (15") 305 (12") 78 (3-1/16") 552H3050N457 (18") 381 (15") 98 (3-7/8") 552H3810N533 (21") 457 (18") 97 (3-13/16") 552H4570N610 (24") 533 (21") 119 (4-11/16") 552H5330N
Runner profile
Locking device
Rear mounting bracketsfor face frame only
Rear mounting bracket for frame cabinets
Dimensions in millimeters (inch equivalents as noted)
612TH295.3750Non-handed bracket
Installation screws
Note: These runners are for 16 (5/8") max. drawer side thickness
Drawer preparation page 14
- One right and one left required per drawer- Minimum interior drawer width 121 (4-3/4")- Height adjustable +3 (1/8")
Standard locking device
T51.1700.04 LT51.1700.04 R
LeftRight
612THInstallation screwspage 14Installation
Accessories page 45 Assembly aids page 47
* 7/8 extension
For use when installing TANDEM runners in face frame cabinets. Not necessary for panel cabinet installation.
- Two required per drawer- Depth and side-to-side self-alignment- Zinc-plated steel
pg. 29Narrow drawerpg. 27 pg. 31 pg. 32Bottom mountRoll-out trayInset drawer
www.cabinetparts.com
25 (31/32")
37 (1-7/16")
33 (1-5/16”)
6 (1/4”)
9 (11/32”) typ.
Min. topclearance
6 (1/4") Inside cabinet width
Drawer width
Ope
ning
13 (1/2”) Drawer bottom recess
Drawer side thicknessmaximum 16 (5/8”)
14 (9/16”)Bottom clearance
System or #7 profilemountingscrews
37
(1-7
/16"
)
21 (13/16")
Drawer height maximum =
opening minus 20 (13/16”)
page 45
10 (3/8")
37 (1-7/16")
4 (5/32") Setback
Profile length
A
B
Inside cabinet depth
9.5 (3/8")
9 (11/32") typ.
295.3750
Rearmountingbracket
2032
(1-1
/4")
(13/
16")
14 (9/16")
Face frame rail
Face
fram
e st
ile
12(15/32")
7 (9/32")
11 (7/16”)
Ø6 x 10 bore for hook
21 (13/16") minimum rear notch
Subject to technical modifications without notice. © 2006 16
Drawer and cabinet specifications
Front view
Profile close-up
Profile mounting specifications
TANDEM Drawer lengthInside cabinet depth with bracket
Profile lengthSystem screw locations
Maximum Minimum A B
552H2290N 229 (9") 293 (11-9/16") 250 (9-7/8") 241 (9-1/2") 133 (5-1/2") 229 (9")
552H3050N 305 (12") 369 (14-9/16") 326 (12-7/8") 317 (12-1/2") 165 (6-1/2") 261 (10-1/4")
552H3810N 381 (15") 446 (17-9/16") 403 (15-7/8") 394 (15-1/2") 165 (6-1/2") 357 (14-1/16")
552H4570N 457 (18") 522 (20-9/16") 479 (18-7/8") 470 (18-1/2") 261 (10-1/4") 453 (17-13/16")
552H5330N 533 (21") 598 (23-9/16") 555 (21-7/8") 546 (21-1/2") 261 (10-1/4") 517 (20-3/8")
Rear mounting bracket
Drawer back preparation
Dimensions in millimeters (inch equivalents as noted)
Example: For 21" inside cabinet width and a 5/8" thick drawer, 21" minus 3/8" = 20-5/8" drawer width
Note: For frame applications. Minimum 3 screws per bracket.
Formula for calculating outside drawer width
For drawer side thickness 16 (5/8") 15 (19/32") 14 (9/16") 13 (1/2") 12 (15/32")
Deduct from inside cabinet width 10 (3/8") 12 (15/32") 14 (9/16") 16 (5/8") 18 (23/32")
Extension Partial
Max. drawer material 16 (5/8")
Dynamic capacity 75 lb.
Static capacity 100 lb.
www.cabinetparts.com
17 Subject to technical modifications without notice. © 2006
TANDEM 552F partial extension drawer runners
Description Basic components
- Partial extension concealed drawer runners - For 19 (3/4") max. drawer side thickness- Zinc coated steel profiles- Concealed roller carriages with permanently lubricated synthetic rollers create a smooth running action- Locking devices enable easy drawer insertion and removal- Force guided right side and ±1.5 (1/16") tolerance compensating left side- Dynamic weight capacity of 75 lb- Static weight capacity of 100 lb
Components
Runner profile
Locking device
Rear mounting bracketfor face frame only
For overall cabinet depth
Drawer length
Extensionloss TANDEM
305 (12") 229 (9") 37 (1-7/16") 552F2290N*381 (15") 305 (12") 78 (3-1/16") 552F3050N457 (18") 381 (15") 98 (3-7/8") 552F3810N533 (21") 457 (18") 97 (3-13/16") 552F4570N610 (24") 533 (21") 119 (4-11/16") 552F5330N
Dimensions in millimeters (inch equivalents as noted)
Other applications
Profile set
Note: These runners are for 19 (3/4") max. drawer side thicknessOne set required per drawer
Overlay application
Rear mounting bracket for frame cabinets
612TH295.3750Non-handed bracket
Installation screws
- One right and one left required per drawer- Minimum interior drawer width 121 (4-3/4")- Height adjustable +3 (1/8")
Standard locking device
T51.1700.04 LT51.1700.04 R
LeftRight
612THInstallation screwspage 14Installation
* 7/8 extension
For use when installing TANDEM runners in face frame cabinets. Not necessary for panel cabinet installation.
Using TANDEM page 13 Drawer preparation page 14
- Two required per drawer- Depth and side-to-side self-alignment- Zinc-plated steel
pg. 29Narrow drawer pg. 31pg. 27 pg. 32Bottom mountRoll-out trayInset drawer
Accessories page 45 Assembly aids page 47
www.cabinetparts.com
25 (31/32")
37 (1-7/16")
33 (1-5/16”)
6 (1/4”)
9 (11/32”) typ.10 (3/8")
37 (1-7/16")
4 (5/32") Setback
Profile length
A
B
Inside cabinet depth
9.5 (3/8")
9 (11/32") typ.
295.3750
Rearmountingbracket
Min. topclearance
6 (1/4") Inside cabinet width
Drawer width
Ope
ning
13 (1/2”) Bottom recess
Drawer side thicknessmaximum 19 (3/4”)
14 (9/16”)Bottom clearance
37
(1-7
/16"
)
24.5 (15/16”)
Drawer height maximum =
opening minus 20 (13/16”)
System or #7 profilemountingscrews
page 45
7 (9/32")
11 (7/16”)
Ø6 x 10 bore for hook
21 (13/16") minimum rear notch
2032
(1-1
/4")
(13/
16")
14 (9/16")
Face frame rail
Face
fram
e st
ile
12(15/32")
Subject to technical modifications without notice. © 2006 18
Drawer and cabinet specifications
Profile close-up
TANDEM Drawer lengthInside cabinet depth with bracket
Profile lengthSystem screw locations
Maximum Minimum A B
552F2290N 229 (9") 293 (11-9/16") 250 (9-7/8") 241 (9-1/2") 133 (5-1/2") 229 (9")
552F3050N 305 (12") 369 (14-9/16") 326 (12-7/8") 317 (12-1/2") 165 (6-1/2") 261 (10-1/4")
552F3810N 381 (15") 446 (17-9/16") 403 (15-7/8") 394 (15-1/2") 165 (6-1/2") 357 (14-1/16")
552F4570N 457 (18") 522 (20-9/16") 479 (18-7/8") 470 (18-1/2") 261 (10-1/4") 453 (17-13/16")
552F5330N 533 (21") 598 (23-9/16") 555 (21-7/8") 546 (21-1/2") 261 (10-1/4") 517 (20-3/8")
Dimensions in millimeters (inch equivalents as noted)
Rear mounting bracket
Front view
Profile mounting specifications
Example: For 21" inside cabinet width and a 3/4" thick drawer, 21" minus 7/16" = 20-9/16" drawer width
Drawer back preparation
Note: For frame applications. Minimum 3 screws per bracket.
Formula for calculating outside drawer width
For drawer side thickness 19 (3/4") 18 (23/32") 17 (21/32")
Deduct from inside cabinet width 11 (7/16") 13 (1/2") 14 (9/16")
Extension Partial
Max. drawer material 19 (3/4")
Dynamic capacity 75 lb.
Static capacity 100 lb.
www.cabinetparts.com
Recommended