View
282
Download
4
Category
Preview:
Citation preview
8/3/2019 Validation and Validation Protocol
1/18
VALIDATION
validation refers to establishingdocumented evidence that a process or
system, when operated withinestablished parameters, can performeffectively and reproducibly to produce a
medicinal product meeting its pre-determined specifications and qualityattributes
8/3/2019 Validation and Validation Protocol
2/18
Validation protocol
A written plan stating how validation will be conducted,including test parameters, product characteristics,production and packaging equipment, and decisionpoints on what constitutes acceptable test results. Thisdocument should give details of critical steps of themanufacturing process that should be measured, theallowable range of variability and the manner in which
the system will be tested.The validation protocol provides a synopsis of what ishoped to be accomplished. The protocol should list theselected process and control parameters, state thenumber of batches to be included in the study, andspecify how the data, once assembled, will be treatedfor relevance. The date of approval by the validationteam should also be noted.In the case where a protocol is altered or modifiedafter its approval, appropriate reasoning for such achange must be documented.
8/3/2019 Validation and Validation Protocol
3/18
Scheme for validation protocol
Part 1. Purpose (the validation) andprerequisites
Part 2. Presentation of the entireprocess and subprocesses, flowdiagram, critical steps/risksPart 3. Validation protocol, approvalPart 4. Installation qualification,drawings
8/3/2019 Validation and Validation Protocol
4/18
Scheme for validation protocolPart 5. Qualification protocol/report
5.1 Subprocess 15.1.1 Purpose5.1.2 Methods/procedures, list of manufacturing
methods, SOPs, and written procedures, asapplicable
5.1.3 Sampling and testing procedures,acceptance criteria (detailed description of, orreference to, established procedures, asdescribed in pharmacopoeias)
5.1.4 Reporting5.1.4.1 Calibration of test equipmentused in the production process5.1.4.2 Test data (raw data)5.1.4.3 Results (summary)
5.1.5 Approval and requalification procedure
5.2 Subprocess 2 (same as for Subprocess 1)5.n Subprocess n
8/3/2019 Validation and Validation Protocol
5/18
Scheme for validationprotocol
Part 6. Product characteristics, test data fromvalidation batchesPart 7. Evaluation, including comparison with the
acceptance criteria and recommendations (includingfrequency of revalidation/requalification)Part 8. Certification (approval)Part 9. If applicable, preparation of an abbreviatedversion of the validation report for external use, forexample by the regulatory authorityThe validation protocol and report may also includecopies of the product stability report or a summary ofit, validation documentation on cleaning, and
analytical methods.
8/3/2019 Validation and Validation Protocol
6/18
PHARMACEUTICAL VALIDATION AND PROCESSCONTROLS IN DRUG DEVELOPMENT
OBJECTIVE
In drug development, pharmaceutical validation and process controls are important to assure that the drug product can meet standards for the identity, strength,quality, purity, and stability of the drug product.
Pharmaceutical validation includes analytical method validation and (manufacturing) process validation.
A validated analytical method is often employed for product testing at various critical stages of a manufacturing process to evaluate whether the manufacturing process does what it purports to do.
For a validated manufacturing process, the current good manufacturing practice requires that a well-written procedure for process controls be established to monitor the performance of the manufacturing process.
The concept can be applied to new drugs, new dosage
forms, and generic drug development.
8/3/2019 Validation and Validation Protocol
7/18
INFORMATIONS ON VALIDATION PROTOCOL
The validation protocol should be numbered, signedand dated, and should contain as a minimum thefollowing information:
objectives, scope of coverage of the validation study
validation team membership, their qualifications andresponsibilities type of validation: prospective, concurrent,
retrospective, re-validation number and selection of batches to be on the validation
study a list of all equipment to be used; their normal and worst
case operating parameters outcome of IQ, OQ for critical equipment requirements for calibration of all measuring devices
8/3/2019 Validation and Validation Protocol
8/18
Informations on validationprotocol (contd.)
critical process parameters and their respectivetolerances
description of the processing steps: copy of themaster documents for the product
sampling points, stages of sampling, methods ofsampling, sampling plans statistical tools to be used in the analysis of data training requirements for the processing operators validated test methods to be used in in-process
testing and for the finished product specifications for raw and packaging materials and
test methods forms and charts to be used for documenting results format for presentation of results, documenting
conclusions and for approval of study results.
8/3/2019 Validation and Validation Protocol
9/18
SUMMARY: Validation??? Documentation Programme.provides high degree of assurance.
To check correctness of method orprocess.
Required by law.To avoid possibility of rejection orrecalled batches.To ensure product uniformity, reproducibility &
quality
8/3/2019 Validation and Validation Protocol
10/18
Validation protocol :
it gives Details of the critical parts of the
manufacturing process.Information about the key parameter tobe measured.
Allowable range of variability in case ofmeasured parameter.
8/3/2019 Validation and Validation Protocol
11/18
Validation of facilities, equipment and
services is called qualification
to confirm that a design of equipment is planned properly.
A) Design Qualification (D.Q.)
B) Installation qualification (I.Q.)
Performance of the tests in order to confirm that a piece of equipment isinstalled properly.
8/3/2019 Validation and Validation Protocol
12/18
Performance of the tests in order to confirm that a piece of equipment is operated properly.
C) Operational qualification (O.Q.)
D) Performance qualification (P.Q.)
Test to demonstrate the effectiveness and reproducibility of a process .
E) Change Control
8/3/2019 Validation and Validation Protocol
13/18
In short : Validation is done
for: Raw material
Process
product
13/85
8/3/2019 Validation and Validation Protocol
14/18
Product Validation: Tablet
Raw MaterialPackaging Material
GranulesCompressed TabletsCoated TabletsPacked Final Product
8/3/2019 Validation and Validation Protocol
15/18
Raw material validation:
Raw material is validated for particle size,surface area, particle size distribution, colour, Appearance, texture, density, flowability ,compressibility etc.
Organolaptic propertyPhysical characteristicChemical characteristicBiological characteristicMicrobiological characteristicStability testingStorage condition
8/3/2019 Validation and Validation Protocol
16/18
Process validation Two stage First identify the critical process
parameter and design protocol Manufacture three batches of product
controlling the critical parameter andtest it for compliance
8/3/2019 Validation and Validation Protocol
17/18
Process validation:
8/3/2019 Validation and Validation Protocol
18/18
Thank you
Recommended