View
2
Download
0
Category
Preview:
Citation preview
TECHNICAL GUIDEWWW.XTREMEIAS.COM
844.365.9462
Extruded Aluminum Trim: Innovative Solutions for Interior Applications
© 2017 XTREMEINTERIOR™ ARCHITECTURAL SOLUTIONS
SPEC
IFIC
AT
ION
SBest Practice/Before Installation:
Read construction drawings to ensure correct layout and placement. Contractor to make sure that blocking has been provided prior to installation for proper installation where necessary.
An outside corner is the best place to begin installation of XtremeInterior™. Choose one that makes the most sense for your project. XtremeInterior reveals offers many options.
Cutting and Painting:
XtremeInterior recommends that full ten-foot length profiles be used when and wherever possible.
XtremeInterior aluminum trim can be cut with a chop saw, using non-ferrous carbide miter saw blade when cutting metal. An abrasive cut-off wheel should never be used to cut aluminum trims.
XtremeInterior recommends that lubricant (WD-40 or grease stick) be applied to the blade before each cut. Lubricant should be cleaned off of trim prior to painting and installation.
Clear Anodized Aluminum Moldings:
XtremeInterior does not recommend painting clear anodized trim. We provide (as a standard), primed and ready to receive paint profiles, that are kept in stock.
If field painting of clear anodized moldings is necessary, the following steps must be taken to improve the bond between the paint and the aluminum surface:
Clean and treat moldings with an acid etch solution (i.e. mild concentration of muriatic acid), then rinse thoroughly and allow to dry. An “acid-etched” primer is also available depending on the paint manufacturer's recommendations.
Use a primer recommended by the paint manufacturer.
Apply the paint coat according to the paint manufacturer's specifications.
XtremeInterior makes no guarantees, nor accepts any responsibility, for the performance of field-applied coatings over anodized finishes.
Installation Instructions for Interior Trim with tape and float Flanges:
Moldings with tape and float flanges are to be installed while the drywall/gypsum board is being installed. The installer must provide space for the moldings at the time of drywall/gypsum board installation or cut the drywall/gypsum board with a router.
The framing / blocking should provide a backer so that moldings can be attached with (recommended) #6 drywall screws 16” on center.
Before the taping process begins, installation flanges should be cleaned. If veneer plaster is specified, the installation flanges must be treated with a bonding agent. Reveals should be masked to prevent compound joint, drywall mud or texture overspray in order to prevent the entering the reveal opening.
Painted aluminum moldings should be masked with vinyl tape. Use cloth or vinyl tape specifically manufactured for masking anodized aluminum trims.
Drywall tape should not overlap the edge of the reveal. An 8” wide trowel should be used to apply the final skim coat.
Fiberglass or self-adhesive drywall tape will shorten taping time and assist in the prevention of possible cracking.
Installation Instructions for Interior Trim without tape and float Flanges:
Trim without tape and float flanges are to be installed prior to the drywall/gypsum board being installed.
The framing should provide a backer so that moldings can be attached with #6 drywall screws 16” on center.
Reveals should be masked in order to prevent compound joint, drywall mud or texture overspray from entering the reveal opening.
Limited Waranty:
Tamlyn warrants defective free products for a period of 10 years for the original purchaser unless otherwise stated for the specific product ordered. Tamlyn products are further warranted as to adequacy of design, provided products are properly specified and installed. This warranty
does not apply in the event products are altered in any way or are improperly installed. Liability is limited to replacement of products proven to be defective. Tamlyn has made no other warranty, expressed or implied, regarding its products, including but not limited to, any warranty regarding merchantability or fitness for a specific purpose. Any claim that a product is defective must be brought within one (1) month of the date of installation of such products to the original purchaser. Customer hereby agrees that no other incidental or consequential damages are the responsibility of Tamlyn.
The following voids any warranty regarding Tamlyn products:
Product has been improperly installed
Building codes have not been followed.
Products not installed by a contractor /installer with common knowledge of the building industry.
Responsibility remains with the architect or engineer, contractor, and owner for the design, application and proper installation of each Tamlyn product. Specifier and user shall determine the suitability of products for specific application and assume all responsibilities in connection there within.
Aluminum does not rust, however it does corrode. XtremeInterior has a protective coating to cover the bare aluminum. When making cuts on XtremeInterior, recoating will be required at ends, surface scratches, or when performing form cuts. Failure to do this voids your warranty. For answers to your technical questions on recoating consult your local paint manufacturer before installation.
Please follow gypsum board manufacturers best practice application when installing any Tamlyn accessory. XtremeInterior profiles are for aesthetic purposes only (the channel and insert pieces are to be installed vertically and up to ____ degrees at an angle. They are not intended to be used as hand rails or any form of storage shelf) the architect and builder are responsible for designing and installing a code compliant building. XtremeInterior products are not a part of a structural design and are not intended to be used as structural members.
RV Reveal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
RVDF Reveal Double Flange . . . . . . . . . . . . . . . . 5
RVRD Reveal Round . . . . . . . . . . . . . . . . . . . . . . . 6
RVRS Reveal Square . . . . . . . . . . . . . . . . . . . . . . 7
RVSA Reveal Square Angled . . . . . . . . . . . . . . . . . 8
RVST Reveal Square Tapered . . . . . . . . . . . . . . . . 9
RVV Reveal V . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
RVVF Reveal V Flange . . . . . . . . . . . . . . . . . . . . . 11
BPR Base Projecting Round . . . . . . . . . . . . . . . . 12
BPRR Base Projecting Round Reveal . . . . . . . . . . . 13
BPS Base Projecting Square . . . . . . . . . . . . . . . . 14
BPSR Base Base Projecting Square Reveal . . . . . . 15
BRDF Base Reveal Double Flange . . . . . . . . . . . . . 16
BRF Base Reveal Flange . . . . . . . . . . . . . . . . . . . 17
BRL Base Reveal Ledge . . . . . . . . . . . . . . . . . . . 18
BSL Base Shadow Line . . . . . . . . . . . . . . . . . . . . 19
CAC Corner Arc . . . . . . . . . . . . . . . . . . . . . . . . . 20
CBD Corner Bead . . . . . . . . . . . . . . . . . . . . . . . . 21
CBV Corner Bevel . . . . . . . . . . . . . . . . . . . . . . . 22
CEL Corner Elliptical . . . . . . . . . . . . . . . . . . . . . 23
CRA Corner Radiused . . . . . . . . . . . . . . . . . . . . 24
CRD Corner Round . . . . . . . . . . . . . . . . . . . . . . 25
CRR Corner Rectangular Radiused . . . . . . . . . . . 26
CRS Corner Rectangular Square . . . . . . . . . . . . . 27
CRT Corner Rectangular Tapered . . . . . . . . . . . . 28
CSQ Corner Square . . . . . . . . . . . . . . . . . . . . . . 29
CXF Corner X . . . . . . . . . . . . . . . . . . . . . . . . . . 30
ICAC Inside Corner Arc . . . . . . . . . . . . . . . . . . . . 31
ICBV Inside Corner Bevel . . . . . . . . . . . . . . . . . . 32
ICEL Inside Corner Elliptical . . . . . . . . . . . . . . . . 33
ICRA Inside Corner Radiused . . . . . . . . . . . . . . . 34
ICRD Inside Corner Round . . . . . . . . . . . . . . . . . 35
ICRF Inside Corner Flange . . . . . . . . . . . . . . . . . 36
ICSQ Inside Corner Square . . . . . . . . . . . . . . . . . 37
CHFS Channel Flush Square . . . . . . . . . . . . . . . . . 38
CHRS Channel Rectangular Square . . . . . . . . . . . . 39
CHSA Channel Square Angled . . . . . . . . . . . . . . . 40
CHST Channel Square Tapered . . . . . . . . . . . . . . 41
IBRR Insert Blade Rectangular Round . . . . . . . . . 42
IBRS Insert Blade Rectangular Square . . . . . . . . . 43
IBRT Insert Blade Rectangular Tapered . . . . . . . . 44
IPRS Insert Projecting Radiused Square . . . . . . . 45
IRSQ Insert Rectangular Square . . . . . . . . . . . . . 46
MCR C Mold . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
MFR F Mold . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
MJR J Mold . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
MKE Knife Edge . . . . . . . . . . . . . . . . . . . . . . . . . 50
MWR W Mold . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
TA
BLE O
F C
ON
TEN
TS
Creates minimalist shadow line with simple reveal
space that allows installa�on ver�cally, horizontally
or diagonally. Can be used in conjunc�on with 5/8”
drywall, panel installa�on and wrapped surface
finishes such as fabric or vinyl wall coverings. Ridged
faces for tape and float. Available in 10' length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
RV
R
EV
EA
L
4
Drywall
Metal Stud
Drywall
Metal Stud
ITEM ID
RV-12
RV-100
RV-200
"A" (REVEAL)
1/2"
1"
2"
"A"
5/8"
Tape & Float
XtremeInterior profiles are subject to alterations without notice or notification.
RV
DF R
EV
EA
L D
OU
BLE F
LA
NG
E
5
Drywall
Metal Stud
ITEM ID
RVDF-12
RVDF-100
RVDF-200
"A" (REVEAL)
1/2"
1"
2"
3/8""A"
5/8"
Drywall
Metal Stud
Creates sleek shadow line with simple reveal space
and double flange arms. Can be installed
ver�cally, horizontally or diagonally. Used in
conjunc�on with 5/8” drywall, panel installa�on
and wrapped surface finishes such as fabric or
vinyl wall coverings. Available in 10' length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
XtremeInterior profiles are subject to alterations without notice or notification.
RV
RD
R
EV
EA
L R
OU
ND
6
Drywall
Metal Stud
Drywall
Metal Stud
ITEM ID
RVRD-12
RVRD-100
RVRD-200
"A" (REVEAL)
1/2"
1"
2"
3/8" "A"
5/8"
Creates an appealing recess with projec�ng details
that allows installa�on ver�cally, horizontally or
diagonally. Can be used in conjunc�on with 5/8”
drywall, panel installa�on and wrapped surface
finishes such as fabric or vinyl wall coverings.
Available in 10' length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
XtremeInterior profiles are subject to alterations without notice or notification.
RV
RS R
EV
EA
L S
QU
AR
E
Drywall
Metal Stud
Drywall
Metal Stud
7
ITEM ID
RVRS-12
RVRS-100
RVRS-200
"A" (REVEAL)
1/2"
1"
2"
3/8""A"
5/8"
Creates an appealing recess with projec�ng square
details that allows installa�on ver�cally, horizontally
or diagonally. Can be used in conjunc�on with 5/8”
drywall, panel installa�on and wrapped surface
finishes such as fabric or vinyl wall coverings.
Available in 10' length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
XtremeInterior profiles are subject to alterations without notice or notification.
RV
SA
REV
EA
L S
QU
AR
E A
NG
LED
8
Drywall
Metal Stud
Drywall
Metal Stud
ITEM ID
RVSA-12
RVSA-100
RVSA-200
"A" (REVEAL)
1/2"
1"
2"
3/8" "A"
5/8"
Creates an appealing recess with projec�ng angled
details that allows installa�on ver�cally,
horizontally or diagonally. Can be used in
conjunc�on with 5/8” drywall, panel installa�on
and wrapped surface finishes such as fabric or
vinyl wall coverings. Available in 10' length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
XtremeInterior profiles are subject to alterations without notice or notification.
RV
ST
REV
EA
L S
QU
AR
E T
APER
ED
9
Drywall
Metal Stud
Drywall
Metal Stud
ITEM ID
RVST-12
RVST-100
RVST-200
"A" (REVEAL)
1/2"
1"
2"
3/8""A"
5/8"
Creates an appealing recess with projec�ng
tapered details that allows installa�on ver�cally,
horizontally or diagonally. Can be used in
conjunc�on with 5/8” drywall, panel installa�on
and wrapped surface finishes such as fabric or vinyl
wall coverings. Available in 10' length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
XtremeInterior profiles are subject to alterations without notice or notification.
RV
V R
EV
EA
L V
10
Drywall
Metal Stud
Drywall
Metal Stud
3/4"
5/8"
Tape & Float
Creates unique shadow line with v shaped reveal
space that allows installa�on ver�cally, horizontally
or diagonally. Can be used in conjunc�on with 5/8”
drywall, panel installa�on and wrapped surface
finishes such as fabric or vinyl wall coverings. Ridged
faces for tape and float. Available in 10' length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
XtremeInterior profiles are subject to alterations without notice or notification.
RV
VF R
EV
EA
L V
FLA
NG
E
11
Drywall
Metal Stud
Drywall
Metal Stud
3/4"
5/8"
3/8"
Creates beau�ful shadow line with v shaped reveal
space and double flanges. Can be installed
ver�cally, horizontally or diagonally. Used in
conjunc�on with 5/8” drywall, panel installa�on
and wrapped surface finishes such as fabric or vinyl
wall coverings. Available in 10' length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
XtremeInterior profiles are subject to alterations without notice or notification.
Drywall
Metal Stud
Metal Stud
Tape & Float
Drywall
BPR
BA
SE P
RO
JEC
TIN
G R
OU
ND
12
ITEM ID
BPR-34
BPR-150
BPR-200
BPR-250
"A" (LENGTH)
3/4"
1-1/2"
2"
2-1/2"
"A"
3/8"
Patent Pending
Stunning profile that creates a recessed base at the
bo�om of a wall just above floor surface or at the
top of a wall just below the ceiling surface.
Projec�ng round edge adds beau�ful detail to any
space. Ridged face provided for taping and
floa�ng. Can be used in conjunc�on with wrapped
surface finishes such as fabric or vinyl wall
coverings. Used horizontally. Available in 10' length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
5/8"
XtremeInterior profiles are subject to alterations without notice or notification.
Drywall
Metal Stud
Metal Stud
Tape & Float
Drywall
BPR
R B
ASE P
RO
JEC
TIN
G R
OU
ND
REV
EA
L
13
ITEM ID
BPRR-250
BPRR-300
"A" (LENGTH)
2-1/2"
3"
"A"
5/8"
3/8"
Patent Pending
Unique profile that creates a combina�on reveal
and projec�ng detail line at the bo�om of a wall
just above floor surface or at the top of a wall just
below the ceiling surface. Projec�ng round edge
adds classic and refined detail. Ridged face
provided for taping and floa�ng. Can be used in
conjunc�on with wrapped surface finishes such as
fabric or vinyl wall coverings. Used horizontally.
Available in 10' length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
5/8"
XtremeInterior profiles are subject to alterations without notice or notification.
Drywall
Metal Stud
Metal Stud
Tape & Float
Drywall
BPS
BA
SE P
RO
JEC
TIN
G S
QU
AR
E
14
ITEM ID
BPS-34
BPS-150
BPS-200
BPS-250
"A" (LENGTH)
3/4"
1-1/2"
2"
2-1/2"
"A"
3/8"
Patent Pending
Sleek profile that creates a recessed base at the
bo�om of a wall just above floor surface or at the
top of a wall just below the ceiling surface.
Projec�ng square edge adds classic and refined
detail. Ridged face provided for taping and floa�ng.
Can be used in conjunc�on with wrapped surface
finishes such as fabric or vinyl wall coverings. Used
horizontally. Available in 10' length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
5/8"
XtremeInterior profiles are subject to alterations without notice or notification.
Metal Stud
Tape & Float
Drywall
15
ITEM ID
BPSR-250
BPSR-300
"A" (LENGTH)
2-1/2"
3"
"A"
5/8"
3/8"
Drywall
Metal Stud
BPSR
BA
SE P
RO
JEC
TIN
G S
QU
ARE R
EV
EA
L
Patent Pending
Unique profile that creates a combina�on reveal
and projec�ng detail line at the bo�om of a wall
just above floor surface or at the top of a wall just
below the ceiling surface. Projec�ng square edge
adds classic and refined detail. Ridged face
provided for taping and floa�ng. Can be used in
conjunc�on with wrapped surface finishes such as
fabric or vinyl wall coverings. Used horizontally.
Available in 10' length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
5/8"
XtremeInterior profiles are subject to alterations without notice or notification.
Drywall
Metal Stud
Drywall
Metal Stud
BR
DF
BA
SE R
EV
EA
L D
OU
BLE F
LA
NG
E
16
Striking profile that creates a recessed base at the
bo�om of a wall just above floor surface or at the
top of a wall just below the ceiling surface. Double
flange creates a reveal for visual impact as well as
protec�ng the bo�om of wall material and crea�ng
a lower recess. Can be used in conjunc�on with
wrapped surface finishes such as fabric or vinyl wall
coverings. Used horizontally. Available in 10' length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
2-1/8"
1/2"
3/8"
3/8"
5/8"
XtremeInterior profiles are subject to alterations without notice or notification.
Drywall
Metal Stud
Drywall
Metal Stud
Tape & Float
BR
F B
ASE R
EV
EA
L F
LA
NG
E
17
Uniquely detailed profile that creates a recessed
base at the bo�om of a wall just above floor
surface or at the top of a wall just below the ceiling
surface. Adding a decora�ve flange as well as a
reveal. Ridged face provided for taping and floa�ng.
Can be used in conjunc�on with wrapped surface
finishes such as fabric or vinyl wall coverings. Used
horizontally. Available in 10' length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
1-7/8"
5/8"
1/2"
5/8"
XtremeInterior profiles are subject to alterations without notice or notification.
Metal Stud
Drywall
Metal Stud
Drywall
BR
L
BA
SE R
EV
EA
L L
ED
GE
18
Tape & Float
Classic profile that creates a recessed base at the
bo�om of a wall just above floor surface or at the
top of a wall just below the ceiling surface with
addi�onal reveal space created by projec�ng edge.
Projec�ng linear edge adds streamlined detail to
any room. Ridged face provided for taping and
floa�ng. Can be used in conjunc�on with wrapped
surface finishes such as fabric or vinyl wall
coverings. Used horizontally. Available in 10' length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
1-3/16"
1/2"
5/8"
XtremeInterior profiles are subject to alterations without notice or notification.
BSL B
ASE S
HA
DO
W L
INE
Drywall
Metal Stud
Drywall
Metal Stud
Tape & Float
19
ITEM ID
BSL-516
BSL-58
BSL-150
BSL-400*
"A" (LENGTH)
5/16"
5/8"
1-1/2"
4"
*BSL-400 also available for 1/2" drywall
Create visually stunning shadow lines with a
minimalist base trim that allows the wall to appear
to float just above the floor surface and allows for
the same effect at the top of the wall just below
the ceiling surface. Can be used ver�cally or
horizontally. Ridged face provided for taping and
floa�ng. Can be used in conjunc�on with wrapped
surface finishes such as fabric or vinyl wall
coverings. Available in 10' length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
"A"
5/8"
XtremeInterior profiles are subject to alterations without notice or notification.
CA
C C
OR
NER
AR
C
20
Metal Stud
Metal Stud
Drywall
Drywall
Simple but stunning corner profile. Provides corner
protec�on and simple design for ver�cal and
horizontal drywall or panel corners. Can be used in
conjunc�on with wrapped surface finishes such as
fabric or vinyl wall coverings. Available in 10'
length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
5/8"
XtremeInterior profiles are subject to alterations without notice or notification.
CBD
CO
RN
ER
BEA
D
21
Metal Stud
Metal Stud
Drywall
Drywall
Tape & Float
R .056"
Minimalis�c bead line corner profile. Provides
corner protec�on and sleek design for ver�cal
drywall or panel corners. Can be used in
conjunc�on with wrapped surface finishes such as
fabric or vinyl wall coverings. Available in 10'
length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
XtremeInterior profiles are subject to alterations without notice or notification.
CBV
C
OR
NER
BEV
EL
22
Metal Stud
Metal Stud
Drywall
Drywall
Tape & Float
"A"
ITEM ID
CBV-100
CBV-200
"A" (BEVEL)
1"
2"
Modern and modest beveled corner profile.
Provides corner protec�on and streamlined design
for ver�cal or horizontal drywall or panel corners.
Can be used in conjunc�on with wrapped surface
finishes such as fabric or vinyl wall coverings.
Available in 10' length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
XtremeInterior profiles are subject to alterations without notice or notification.
CEL C
OR
NER
ELLIP
TIC
AL
Metal Stud
Metal Stud
Drywall
Drywall
Tape & Float
23
Patent Pending
Design feature with ellip�cal corner for ver�cal and
horizontal (for fur-down applica�ons) drywall or
panel corners. Can be used in conjunc�on with
wrapped surface finishes such as fabric or vinyl wall
coverings. Unique design with stunning visual
results. Provides corner protec�on and reveal
creates the illusion of a floa�ng corner. Ridged faces
provided for taping and floa�ng. Available in 10'
length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
1/4"
1-1/2"
5/8"
XtremeInterior profiles are subject to alterations without notice or notification.
CR
A C
OR
NER
RA
DIU
SED
Metal Stud
Metal Stud
Drywall
Drywall
Tape & Float
24
Patent Pending
Design feature with rounded edge for ver�cal and
horizontal (for fur-down applica�ons) drywall or
panel corners. Can be used in conjunc�on with
wrapped surface finishes such as fabric or vinyl wall
coverings. Provides corner protec�on and reveal
creates the illusion of a floa�ng corner. Ridged faces
provided for taping and floa�ng. Available in 10'
length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
1/4"
5/8"
1-1/8"
XtremeInterior profiles are subject to alterations without notice or notification.
CR
D C
OR
NER
RO
UN
D
Metal Stud
Metal Stud
Drywall
Drywall
Tape & Float
25
Patent Pending
Design feature with circular corner for ver�cal and
horizontal (for fur-down applica�ons) drywall or
panel corners. Can be used in conjunc�on with
wrapped surface finishes such as fabric or vinyl wall
coverings. Provides corner protec�on and reveal
creates the illusion of a floa�ng corner. Ridged faces
provided for taping and floa�ng. Available in 10'
length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
1/4"
R .50"
5/8"
XtremeInterior profiles are subject to alterations without notice or notification.
CR
R
C
OR
NER
REC
TA
NG
ULA
R R
AD
IUSED
Metal Stud
Metal Stud
Drywall
Drywall
Tape & Float
26
Patent Pending
Design feature with rounded asymmetrical corner
for ver�cal and horizontal (for fur-down applica�ons)
drywall or panel corners. Can be used in conjunc�on
with wrapped surface finishes such as fabric or vinyl
wall coverings. Provides corner protec�on and reveal
creates the illusion of a floa�ng corner. Ridged faces
provided for taping and floa�ng. Available in 10'
length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
2-5/8"
1/4"
1-1/8"5/8"
XtremeInterior profiles are subject to alterations without notice or notification.
CR
S C
OR
NER
REC
TA
NG
ULA
R S
QU
AR
E
Metal Stud
Metal Stud
Drywall
Drywall
Tape & Float
27
Patent Pending
Design feature with asymmetrical corner for ver�cal
and horizontal (for fur-down applica�ons) drywall or
panel corners. Can be used in conjunc�on with
wrapped surface finishes such as fabric or vinyl wall
coverings. Provides corner protec�on and reveal
creates the illusion of a floa�ng corner. Ridged faces
provided for taping and floa�ng. Available in 10'
length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
2-5/8"
1/4"
5/8"
XtremeInterior profiles are subject to alterations without notice or notification.
CR
T
C
OR
NER
REC
TA
NG
ULA
R T
APER
ED
Metal Stud
Metal Stud
Drywall
Drywall
Tape & Float
28
Patent Pending
Design feature with tapering asymmetrical corner for
ver�cal and horizontal (for fur-down applica�ons)
drywall or panel corners. Can be used in conjunc�on
with wrapped surface finishes such as fabric or vinyl
wall coverings. Provides corner protec�on and reveal
creates the illusion of a floa�ng corner. Ridged faces
provided for taping and floa�ng. Available in 10'
length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
2-5/8"
1/4"
1-1/8"5/8"
XtremeInterior profiles are subject to alterations without notice or notification.
Metal Stud
Metal Stud
Drywall
Drywall
Tape & Float
CSQ
CO
RN
ER
SQ
UA
RE
29
Patent Pending
Design feature and finished edge for ver�cal and
horizontal (for fur-down applica�ons) drywall or panel
corners. Can be used in conjunc�on with wrapped
surface finishes such as fabric or vinyl wall coverings.
Provides corner protec�on and reveal creates the
illusion of a floa�ng corner. Ridged faces provided for
taping and floa�ng. Available in 10' length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
1/4"1-1/8"
5/8"
XtremeInterior profiles are subject to alterations without notice or notification.
CXF C
OR
NER
X
30
Metal Stud
Drywall
ITEM ID
CXF-14
CXF-38
CXF-100
"A" (FLANGE)
1/4"
3/8"
1"
Metal Stud
Drywall
Classic and clean corner profile with flange arms.
Provides corner protec�on and beau�ful design for
ver�cal and horizontal drywall or panel corners.
Can be used in conjunc�on with wrapped surface
finishes such as fabric or vinyl wall coverings.
Available in 10' length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
"A"
5/8"
XtremeInterior profiles are subject to alterations without notice or notification.
ICA
C IN
SID
E C
OR
NER
AR
C
31
Metal Stud
Drywall
Tape & Float
Drywall
Metal Stud
ITEM ID
ICAC-100
ICAC-200
"A" (RADIUS)
1"
2"
"A"
Coordina�ng inside corner for the CAC profile. Can be
used ver�cally and horizontally in conjunc�on with
drywall, panels, and wrapped surface finishes. Ridged
faces allow for taping and floa�ng. Available in 10'
length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
XtremeInterior profiles are subject to alterations without notice or notification.
ICBV
INSID
E C
OR
NER
BEV
EL
32
Metal Stud
Drywall
Tape & Float
Drywall
Metal Stud
ITEM ID
ICBV-100
ICBV-200
"A" (BEVEL)
1"
2"
"A"
Coordina�ng inside corner for the CBV profile. Can
be used ver�cally and horizontally in conjunc�on
with drywall, panels, and wrapped surface finishes.
Ridged faces allow for taping and floa�ng.
Available in 10' length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
XtremeInterior profiles are subject to alterations without notice or notification.
ICEL IN
SID
E C
OR
NER
ELLIP
TIC
AL
Tape & Float
33
Drywall
Metal Stud
Metal Stud
Drywall
Patent Pending
Coordina�ng inside corner for the CEL profile. Can
be used ver�cally and horizontally in conjunc�on
with drywall, panels, and wrapped surface finishes.
Ridged faces allow for taping and floa�ng.
Available in 10' length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
1-1/2"
1/4"
XtremeInterior profiles are subject to alterations without notice or notification.
ICR
A
IN
SID
E C
OR
NER
RA
DIU
SED
Metal Stud
Drywall
Tape & Float
34
Drywall
Metal Stud
Patent Pending
Coordina�ng inside corner for the CRA profile. Can
be used ver�cally and horizontally in conjunc�on
with drywall, panels, and wrapped surface finishes.
Ridged faces allow for taping and floa�ng.
Available in 10' length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
1/4" 1-1/8"
XtremeInterior profiles are subject to alterations without notice or notification.
ICR
D IN
SID
E C
OR
NER
RO
UN
D
Metal Stud
Drywall
Tape & Float
35
Drywall
Metal Stud
Patent Pending
Coordina�ng inside corner for the CRD profile. Can
be used ver�cally and horizontally in conjunc�on
with drywall, panels, and wrapped surface finishes.
Ridged faces allow for taping and floa�ng.
Available in 10' length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
1/4"
R .50"
XtremeInterior profiles are subject to alterations without notice or notification.
ICR
F
IN
SID
E C
OR
NER
FLA
NG
E
36
Metal Stud
Drywall
Drywall
Metal Stud
Coordina�ng inside corner for the CXF profile. Can
be used ver�cally and horizontally in conjunc�on
with drywall, panels, and wrapped surface finishes.
Tape and float unnecessary due to flange detail.
Available in 10' length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
3/8"
5/8"
XtremeInterior profiles are subject to alterations without notice or notification.
ICSQ
INSID
E C
OR
NER
SQ
UA
RE
Metal Stud
Drywall
Tape & Float
37
Drywall
Metal Stud
Patent Pending
Coordina�ng inside corner for the CSQ profile. Can
be used ver�cally and horizontally in conjunc�on
with drywall, panels, and wrapped surface finishes.
Ridged faces allow for taping and floa�ng.
Available in 10' length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
1/4"1-1/8"
XtremeInterior profiles are subject to alterations without notice or notification.
Drywall
Metal Stud
Tape & Float
Drywall
Metal Stud
CH
FS
C
HA
NN
EL F
LU
SH
SQ
UA
RE
38
5/8"
Patent Pending
Anchor channel for two piece system. Ridged faces
provided for taping and floa�ng and allow insert
piece to appear to stand alone. Can be used in
conjunc�on with 5/8" drywall or panel installa�on
and with wrapped surface finishes such as fabric or
vinyl wall coverings. Used ver�cally or diagonally
and in approved condi�ons, horizontally. Available
in 10' length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
XtremeInterior profiles are subject to alterations without notice or notification.
Drywall
Metal Stud
Drywall
Metal Stud
CH
RS C
HA
NN
EL R
EC
TA
NG
ULA
R S
QU
AR
E
5/8"
39
3/8"
Patent Pending
Anchor channel for two piece system. Ridged faces
provided for taping and floa�ng and classic square
projec�ons add visual impact when paired with an
insert piece. Can be used in conjunc�on with 5/8"
drywall, panel installa�on and with wrapped surface
finishes such as fabric or vinyl wall coverings. Used
ver�cally or diagonally and in approved condi�ons,
horizontally. Available in 10' length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
XtremeInterior profiles are subject to alterations without notice or notification.
Drywall
Metal Stud
Drywall
Metal Stud
CH
SA
CH
AN
NEL S
QU
AR
E A
NG
LED
40
5/8"
3/8"
Patent Pending
Anchor channel for two piece system. Ridged faces
provided for taping and floa�ng and angled detail adds
a unique touch to a classic look. Can be used in
conjunc�on with 5/8" drywall, panel installa�on and
with wrapped surface finishes such as fabric or vinyl
wall coverings. Used ver�cally or diagonally and in
approved condi�ons, horizontally. Available in 10'
length.
6063 T5 aluminum with standard clear anodized or primed finish. Anodized color and powder coa�ng finishes available with custom color matching.
XtremeInterior profiles are subject to alterations without notice or notification.
Drywall
Metal Stud
Drywall
Metal Stud
CH
ST
CH
AN
NEL S
QU
AR
E T
APER
ED
5/8"
3/8"
41
Patent Pending
Anchor channel for two piece system. Ridged faces
provided for taping and floa�ng and unique tapered
square edges create a dynamic look when paired
with an insert piece. Can be used in conjunc�on with
5/8" drywall, panel installa�on and with wrapped
surface finishes such as fabric or vinyl wall coverings.
Used ver�cally or diagonally and in approved
condi�ons, horizontally. Available in 10' length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
XtremeInterior profiles are subject to alterations without notice or notification.
Drywall
Metal Stud
Tape & Float
Drywall
Metal StudIBR
R
IN
SER
T B
LA
DE R
EC
TA
NG
ULA
R R
OU
ND
42
ITEM ID
IBRR-100
IBRR-200
IBRR-300
"A" (LENGTH)
1"
2"
3"
"A"
1/2"
Patent Pending
Paired with Channel Reveal this unique blade
projec�on creates an a�rac�ve look in any space.
Ridged faces provided for taping and floa�ng with
drywall installa�on. Can also be used in
conjunc�on with panels and wrapped surface
finishes such as fabric or vinyl wall coverings. Used
ver�cally or diagonally. Available in 10' length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
XtremeInterior profiles are subject to alterations without notice or notification.
Drywall
Metal Stud
Tape & Float
Drywall
Metal Stud
IBR
S IN
SER
T B
LA
DE R
EC
TA
NG
ULA
R S
QU
AR
E
43
ITEM ID
IBRS-100
IBRS-200
IBRS-300
"A" (LENGTH)
1"
2"
3"
"A"
1/4"
Patent Pending
Paired with Channel Reveal this blade projec�on
with reveals adds refinement and class. Ridged
faces provided for taping and floa�ng with drywall
installa�on. Can also be used in conjunc�on with
panels and wrapped surface finishes such as fabric
or vinyl wall coverings. Used ver�cally or diagonally.
Available in 10' length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
XtremeInterior profiles are subject to alterations without notice or notification.
Drywall
Metal Stud
Tape & Float
Drywall
Metal StudIBR
T
IN
SER
T B
LA
DE R
EC
TA
NG
ULA
R T
APER
ED
44
ITEM ID
IBRT-100
IBRT-200
IBRT-300
"A" (LENGTH)
1"
2"
3"
"A"
1/2"
Patent Pending
Paired with Channel Reveal this exclusive projec�on
creates an impressive look with a detailed notch blade.
Ridged faces provided for taping and floa�ng with
drywall installa�on. Can also be used in conjunc�on
with panels and wrapped surface finishes such as fabric
or vinyl wall coverings. Used ver�cally or diagonally.
Available in 10' length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
XtremeInterior profiles are subject to alterations without notice or notification.
Drywall
Metal Stud
Tape & Float
Drywall
Metal Stud
IPR
S IN
SER
T P
RO
JEC
TIN
G R
AD
IUSED
SQ
UA
RE
45
ITEM ID
IPRS-0
IPRS-100
IPRS-200
IPRS-300
"A" (LENGTH)
0"
1"
2"
3"
"A"
5/16"
Paired with Channel Reveal this subtle projec�on
creates a classic look in drywall or panel
installa�on. Can also be used in conjunc�on with
wrapped surface finishes such as fabric or vinyl wall
coverings. Ridged faces provided for taping and
floa�ng. Used ver�cally or diagonally. Available in
10' length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
XtremeInterior profiles are subject to alterations without notice or notification.
Drywall
Metal Stud
Tape & Float
Drywall
Metal Stud
IRSQ
INSER
T R
EC
TA
NG
ULA
R S
QU
AR
E
"A"
3/4"
46
ITEM ID
IRSQ-0
IRSQ-100
IRSQ-200
IRSQ-300
"A" (LENGTH)
0"
1"
2"
3"
Paired with Channel Reveal this classic projec�on
creates a modern look in drywall or panel
installa�on. Can also be used in conjunc�on with
wrapped surface finishes such as fabric or vinyl wall
coverings. Ridged faces provided for taping and
floa�ng. Used ver�cally or diagonally.
Available in 10' length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
XtremeInterior profiles are subject to alterations without notice or notification.
MC
R C
MO
LD
47
Drywall
Metal Stud
Tape & Float
Ceiling
Metal Stud
Ceiling
Drywall
Clean finish design with reveal detail for drywall
termina�ons at ceilings, windows, doors and other
material transi�ons. Can be installed horizontally or
ver�cally. Can be used in conjunc�on with 5/8"
drywall, panel installa�on and with wrapped
surface finishes such as fabric or vinyl wall
coverings. Available in 10' length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
1"
5/8"
XtremeInterior profiles are subject to alterations without notice or notification.
MFR
F M
OLD
48
Drywall
Metal Stud
Ceiling
Metal Stud
Ceiling
Drywall
Clean finish design with reveal detail for drywall
termina�ons at ceilings, windows, doors and other
material transi�ons. Can be installed horizontally
or ver�cally. Can be used in conjunc�on with 5/8"
drywall, panel installa�on and with wrapped
surface finishes such as fabric or vinyl wall
coverings. Available in 10' length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
1"
3/8"
5/8"
XtremeInterior profiles are subject to alterations without notice or notification.
MJR
J MO
LD
49
ITEM ID
MJR-14
MJR-38
MJR-50
"A" (FLANGE)
1/4"
3/8"
1/2"
Metal Stud
Drywall
Metal Stud
Drywall
Classic and clean design provides smooth finish at
edges of drywall or at material transi�ons. Can be
installed horizontally or ver�cally. Can be used in
conjunc�on with 5/8" drywall, panel installa�on
and with wrapped surface finishes such as fabric or
vinyl wall coverings. Available in 10' length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
"A"
5/8"
XtremeInterior profiles are subject to alterations without notice or notification.
MK
E K
NIF
E E
DG
E
50
Fur down
Ceiling
Tape & Float
ITEM ID
MKE-30
MKE-45
"A" (ANGLE)
30°
45°
"A"
Wall
"B"
"B"
1-3/8"
3/4"
Wall
Ceiling
Creates a sharp 'knife edge' at ceiling drywall
termina�ons. Clean, crisp look crea�ng unique
ceiling design and allows for LED ligh�ng or shadow
line. Can be used in conjunc�on with 5/8" drywall,
panel installa�on and with wrapped surface
finishes such as fabric or vinyl wall coverings.
Available in 10' length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
XtremeInterior profiles are subject to alterations without notice or notification.
MW
R W
MO
LD
51
Drywall
Metal Stud
Ceiling
ITEM ID
MWR-516
MWR-58
MWR-150
"A" (REVEAL)
5/16"
5/8"
1-1/2"
5/8"
"A" 3/4"
Metal Stud
Ceiling
Drywall
Streamlined design with reveal detail for drywall
termina�ons at ceilings and other material
transi�ons. Can be used in conjunc�on with 5/8"
drywall, panel installa�on and with wrapped
surface finishes such as fabric or vinyl wall
coverings. Available in 10' length.
6063 T5 aluminum with standard clear anodized or
primed finish. Anodized color and powder coa�ng
finishes available with custom color matching.
XtremeInterior profiles are subject to alterations without notice or notification.
CLEAR
CHAMPAGNE
LIGHT BRONZE
MEDIUM BRONZE
DARK BRONZE
BLACK
*Anodized color options shown above.
XtremeInterior™ extruded profiles are provided standard with a primed finish using a proprietary primer suitable for field painting using most paint materials. Ideal application is with a direct to metal alkyd enamel. Consult your local paint manufacturers for best practice and proper paint selection and application. Custom color powder coating available upon request (minimum applies).
All anodized finishes are provided within an industry range of color consistency and can vary slightly from item to item. Special order anodized colors are subject to specific quantity minimums by item. Anodizing is an electrochemical conversion process that deposits an oxide film on the aluminum profile. A natural oxidation process occurs on all bare aluminum, however, producing the oxidation process artificially through anodizing creates a thicker, harder, and more durable oxide film which is an extremely durable finish resistant to most forms of airborne corrosion.
Recommended