Iuwne10 S02 L05

Basic Cisco WLAN Installation

Roaming

Mobility Groups, Mobility Domains

Controller > General

A Cisco Wireless LAN Controller (WLC) can only reside in a single mobility group.

Controller > Mobility Management > Mobility Groups

There are two methods to define the mobility group: Add a member using either the New or Edit All option, in which all members are represented in a text format.A controller can know members of other mobility groups.

Roaming Concept

Roaming refers to movement of clients across Cisco APs while transmitting

Roaming can occur across different mobility groups, but must be within a mobility domain

The Cisco WLC can reside in only a single mobility group The following should be consistent for mobility groups:

– Mobility group membership

– Code across all member controllers

– LWAPP mode across all member controllers

– ACLs configured on all member controllers

– WLAN configuration

– Virtual IP address Two types of roaming

– Intrasubnet roaming (Layer 2)

– Intersubnet roaming (Layer 3)

Cisco Wireless Layer 2 Roaming

Single Cisco WLC

Multiple Cisco WLCs in the same subnetwork

Transparent to the client

The session is sustained during connection to the new AP

The client continues using the same DHCP-assigned or static IP address

Client Roaming Within a Subnetwork

Cisco Wireless Layer 3 Roaming

Multiple Cisco WLCs in different subnetworks

Transparent to the client

The session is sustained during connection to the new AP

Tunnel between the anchor Cisco WLC and foreign Cisco WLC along with special handling of the client traffic by both controllers allows the client to continue using the same DHCP or client-assigned IP address while the session remains active

Set up via either a symmetric or asymmetric tunnel

Client Roaming Across Subnetworks

Roaming Example—Preroaming

Roaming Example—Layer 3 Asymmetric

Roaming Example—Layer 3 Asymmetric (Cont.)

Roaming Example—Layer 3 Symmetric

Roaming Example—Layer 3 Symmetric(Cont.)

Symmetric or Asymmetric Tunnelling

Roaming: Tunnels (Symmetric Example)

Cisco Wireless Mobility Anchor

Cisco WirelessMobility Anchor Considerations

A foreign session to the anchor is set up ahead of client IP address determination.– The foreign controller will have no knowledge of Layer 3 client

information.

Web authentication is supported, but authentication will occur on the mobility anchor as opposed to the local controller.

This mobility anchor function is only available on Cisco 4400 Series Wireless LAN Controllers and Cisco WiSM blades.– 2100/WLCM can be foreign controller, but not anchor the guest

tunnel.

WLANs > Mobility Anchors

Controller > Mobility Management > Mobility Anchor Config

Summary

Controllers can be part of the same mobility group, which allows them to exchange information about clients.

Roaming occurs when a stations changes connection point while transmitting.

At Layer 2, credentials are passed from one controller to the other to ensure seamless mobility.

At Layer 3, roaming can be symmetric or asymmetric, to maintain the client IP address or complete connection to the original subnet.

When roaming is asymmetric, the mobility anchor feature allows a partial symmetric configuration based on the WLAN.

Iuwne10 S02 L05

Technology

L05 thriller conventions

Iuwne10 S05 L05

Iuwne10 S02 L06

Iuwne10 S06 L03

Iuwne10 S04 L06

Iuwne10 S01 L02

Iuwne10 S05 L03

Iuwne10 S03 L03

C++ L05-Functions

L05 time management

L05 Frameworks

Iuwne10 Lg

Iuwne10 S04 L03

Iuwne10 S05 L02

L05 - Equilibrium

L05 - Arrays

Iuwne10 S06 L02

L05 Interaction

Iuwne10 S02 L07

Iuwne10 S00