www.norbar.com

NSD SerieS HyDraulic WreNcH

NHcl SerieS HyDraulic WreNcH

NSD Series

Square Drive

(inches)

Min/Max,N.m

@10,000 p.s.i (+\- 3%)

Weight*(kg)

Reaction Area - RA

(mm)

Length L1

(mm)

Length L2

(mm)

Length L3

(mm)

Radius R

(mm)

Height H1

(mm)

Height H2

(mm)

Width W1

(mm)

Width W2

(mm)

Width W3

(mm)

NSD-1900 3/4 194/1,874 2.38 94 40 133 151 30 104 145 50 69 56

NSD-4500 1 355/3,960 5.10 136 47 183 202 32 124 166 70 91 81

NSD-8000 1-1/2 765/6,928 7.80 139 55 193 214 44 151 199 76 114 89

NSD-15000 1-1/2 1,407/14,633 13.56 165 57 222 239 52 187 232 99 136 127

NSD-27000 2-1/2 2,377/2,4315 28.12 191 88 264 295 76 233 274 126 189 141

NSD-40000 2-1/2 3,577/34,986 34.01 191 88 276 298 79 248 289 149 213 141

NSD-60000† 2-1/2 ** 65.77 189 186 318 338 83 285 320 146 210 140

NSD-80000† 2-1/2 ** 133.80 223 150 373 406 95 356 396 184 248 146

*Weight includes tool, reaction member and square drive. †Steel Casting **Please inquire for additional information.

NHL-1800 Heads(mm)

ATF Radius P/R

19 27 10

27 30 9

32 33 9

37 36 9

36 38 9

46 41 9

51 44 9

NHL-4500 Heads(mm)

ATF Radius P/R

32 35 9

37 37 9

41 40 9

46 43 10

48 45 12

51 45 10

56 48 10

60 50 10

65 54 12

70 57 12

75 60 12

NHL-9500 Heads(mm)

ATF Radius P/R

51 46 12

56 48 12

60 51 12

65 55 12

70 61 14

75 65 13

76 67 16

86 72 16

95 77 16

NHL-14000 Heads(mm)

ATF Radius P/R

60 51 11

65 55 12

70 61 14

75 65 13

76 67 16

86 72 24

95 78 24

105 83 24

NHL-23000 Heads(mm)

ATF Radius P/R

70 64 23

75 67 23

76 69 25

86 74 25

95 81 26

105 85 26

115 91 26

125 99 26

135 104 26

NHL-35000 Heads(mm)

ATF Radius P/R

86 74 24

95 81 26

105 85 25

115 91 25

125 98 25

135 104 26

145 110 28

NHL-65000 Heads(mm)

ATF Radius P/R

115 100 33

125 105 33

135 110 33

145 116 32

155 121 32

165 127 32

175 133 32

185 138 32

NHCSeries

Min/Max,N.m

@10,000 p.s.i (+\- 3%)

Length (mm)

Height(mm)

Body Width(mm)

Head Width(mm)

Range(mm)

Weight with Head(kg)

NHC-1800 159/1,754 159 102 28 24 19 - 51 3.29

NHC-4500 399/4,168 178 146 37 27* or 30† 32 - 75 4.20

NHC-9500 904/9,354 235 159 38 38 51 - 98 6.35

NHC-14000 1,342/13,423 248 203 50 50 60 - 108 11.11

NHC-23000 2,051/21,627 286 235 50 62 70 - 137 19.05

NHC-35000 3,064/32,024 286 235 74 75 89 - 146 25.85

NHC-65000 ** ** ** ** ** ** **

*32 to 51 Heads †56 to 75 Heads §Steel Cylinders Only **Please inquire for additional information.

Norbar Inline hydraulic ratchet wrenches require minimum clearance while applying torque on the same plane as the nut, providing a marked improvement over square drive socket wrenches. Our patented design breakthrough reduces the overall dimensions of the inline ratcheting head allowing it to fit almost every application.

Norbar Torque ToolS - HyDraulic WreNcHeS

NSD Series NHC/L SeriesNorbar square drive hydraulic ratchet wrenches offer a cost efficient option to handle a wide range of bolt tightening and break-out needs. The NSD Series ratchet wrench employs a “patented design” which increases accuracy and reduces the number of moving parts. Our robust and lightweight aluminum body completely encloses the drive train assembly keeping the crucial lubricant inside the tool while significantly reducing the opportunity for outside elements to contaminate the inside of the tool.

For more information on torque and tension products, visit our website: www.norbar.com

Square Drive - Tool Specifications

Hex Link - Tool Specifications

New ZealaNd

65A O’Rorke RoadPenrose Auckland NZTel: +64 (0)9 579 8653Fax: +64 (0)9 579 8654Email: nz@norbar.com.au

westerN australia

Unit 3/95 Bannister RoadCanning Vale WA 6155Tel: +61 (0)8 9455 7717Fax: +61 (0)8 9455 7979Email: wa@norbar.com.au

QueeNslaNd

Unit 5/55 Donaldson RoadRocklea QLD 4106Tel: +61 (0)7 3216 7600Fax: +61 (0)7 3216 6392Email: qld@norbar.com.au

Victoria

Unit 6/810 Princes HighwaySpringvale VIC 3171Tel: +61 (0)3 9562 3382Fax: +61 (0)3 9562 3072Email: vic@norbar.com.au

south east asia / siNgapore

60 Kaki Bukit Place#09-16 Eunos Tech-PackSingapore 415979Tel: +65 6841 1371Fax: +65 6841 1372Email: singapore@norbar.com.au

New south wales

Unit 33/72 - 80 Percival RoadSmithfield NSW 2164Tel: +61 (0)2 9725 2831Fax: +61 (0)2 9604 0951Email: nsw@norbar.com.au

head office - south australia45-47 Raglan Avenue, Edwardstown SA, 5039 Australia

Tel: +61 (0)8 8292 9777 Fax: +61 (0)8 8292 9799Email: norbar@norbar.com.au

www.norbar.com

NSD Series

Square Drive (in)

Min/Max,N.m

@10,000 p.s.i (+\- 3%)

Min/Max,lbf.ft

@10,000 p.s.i (+\- 3%)

Weight*(kg)

Reaction Area - RA

(mm)

Length L1

(mm)

Length L2

(mm)

Length L3

(mm)

Radius R

(mm)

Height H1

(mm)

Height H2

(mm)

Width W1

(mm)

Width W2

(mm)

Width W3

(mm)

NSD-1900 ¾ 194-1,874 143-1,382 2.38 94 40 133 151 30 104 145 50 69 56

NSD-4500 1 355-3,960 262-2,921 5.10 136 47 183 202 32 124 166 70 91 81

NSD-8000 1-1/2 765-6,928 564-5,110 7.80 139 55 193 214 44 151 199 76 114 89

NSD-15000 1-1/2 1,407-14,633 1,038-10,793 13.56 165 57 222 239 52 187 232 99 136 127

NSD-27000 2-1/2 2,377-24,315 1,753-17,934 28.12 191 88 264 295 76 233 274 126 189 141

NSD-40000 2-1/2 3,577-34,986 2,638-25,804 34.01 191 88 276 298 79 248 289 149 213 141

NSD-60000† 2-1/2 ** ** 65.77 189 186 318 338 83 285 320 146 210 140

NSD-80000† 2-1/2 ** ** 133.80 223 150 373 406 95 356 396 184 248 146

*Weight includes tool, reaction member and square drive. †Steel Casting **Please inquire for additional information.

Hydraulic torque MultipliersSquare drive (NSd) Series Norbar square drive hydraulic ratchet wrenches offer a cost efficient option to handle a wide range of bolt tightening and break-out needs. The NSD Series ratchet wrench employs a “patented design” which increases accuracy and reduces the number of moving parts. Our robust and lightweight aluminum body completely encloses the drive train assembly keeping the crucial lubricant inside the tool while significantly reducing the opportunity for outside elements to contaminate the inside of the tool.

Square Drive - Tool Specifications

Hydraulic torque MultipliersHydraulic cylinder/link (NHc/l) SeriesNorbar Inline hydraulic ratchet wrenches require minimum clearance while applying torque on the same plane as the nut, providing a marked improvement over square drive socket wrenches. Our patented design breakthrough reduces the overall dimensions of the inline ratcheting head allowing it to fit almost every application.

NHCSeries

Min-Max, N.m @10,000 p.s.i (+\-

3%)

Min-Max, lbf.ft@10,000 p.s.i (+\-

3%)

Length (mm)

Height(mm)

Body Width(mm)

Head Width(mm)

Range(mm)

Weight with Head

(kg)

NHC-1800 159-1,754 117-1,294 159 102 28 24 19 - 51 3.29

NHC-4500 399-4,168 294-3,074 178 146 37 27* or 30† 32 - 75 4.20

NHC-9500 904-9,354 667-6,899 235 159 38 38 51 - 98 6.35

NHC-14000 1,342-13,423 990-9,900 248 203 50 50 60 - 108 11.11

NHC-23000 2,051-21,627 1,513-15,951 286 235 50 62 70 - 137 19.05

NHC-35000 3,064-32,024 2,260-23,620 286 235 74 75 89 - 146 25.85

NHC-65000 4,711-60,720 3,475-44,785 ** ** ** ** ** ** *32 to 51 Heads †56 to 75 Heads §Steel Cylinders Only **Please inquire for additional information.

Norbar Hydraulic Cylinder/Link Tool Specifications

Hex Link SpecificationsNHL-1800 Heads

(mm)NHL-4500 Heads

(mm)NHL-9500 Heads

(mm)NHL-14000 Heads

(mm)NHL-23000 Heads

(mm)NHL-35000 Heads

(mm)NHL-65000 Heads

(mm)

ATF Radius P/R ATF Radius P/R ATF Radius P/R ATF Radius P/R ATF Radius P/R ATF Radius P/R ATF Radius P/R19 27 10 32 35 9 51 46 12 60 51 11 70 64 23 86 74 24 115 100 3327 30 9 37 37 9 56 48 12 65 55 12 75 67 23 95 81 26 125 105 3332 33 9 41 40 9 60 51 12 70 61 14 76 69 25 105 85 25 135 110 3337 36 9 46 43 10 65 55 12 75 65 13 86 74 25 115 91 25 145 116 3242 38 9 48 45 12 70 61 14 76 67 16 95 81 26 125 98 25 155 121 3246 41 9 51 45 10 75 65 13 86 72 24 105 85 26 135 104 26 165 127 3251 44 9 56 48 10 76 67 16 95 78 24 115 91 26 145 110 28 175 133 32

60 50 10 86 72 16 105 83 24 125 99 26 185 138 3265 54 12 95 77 16 135 104 2670 57 1275 60 12

T +61 (0)8 8292 9777 | F +61 (0)8 8292 9799 | E norbar@norbar.com.au | www.norbar.com

air Powered consoles

Air Powered Console Model Number

Oil Delivery per Minute

Oil Reservoir (Litre)

Usable Oil (inches3)

Overall Width (cm)

Overall Length (cm)

Overall Height (cm)

Pump Weight w/ Oil (kg)

NOR-SAHC465 in³ @100psi

9.46 590 42 24.1 50.3 29.555 in³ @ 10,000psi

• Use where air is the preferred source of power • Powerful 3hp motor starts under load • External adjustable pressure regulator • Retract side internal relief valve protects tool • Use for double or single acting tools

Air Motor, Air Control

• 3hp, 50 cfm @ 80 psi • Pneumatic remote control with 30-foot

cord

electric Powered consoles

Electric Powered Console

Model Number

Oil Delivery per Minute

Oil Reservoir (Litre)

Usable Oil (inches3)

Overall Width (cm)

Overall Length (cm)

Overall Height (cm)

Pump Weight w/ Oil (kg)

NOR-SEHC704 in³ @100psi

9.46 525 43.5 24.1 46 34.156 in³ @ 10,000psi

These pumps have been continually upgraded over the last 40 years and some of the originals are still in service! Equipped with a 1-1/8 horse power, single phase, universal motor; they have a noise level of 90-95 dBA. These power consoles offer the best weight to performance ratio of any of our electric/hydraulic pumps. CSA rated for intermittent duty.

• Two-speed high performance pump • External adjustable pressure regulator • Retract side internal relief valve protects tool • Hand remote • Use for double or single acting tools • Remote control with 30-foot cord

Electric Motor

• 1-1/8 hp, 12000 rpm Remote control with 30-foot cord

• 115V, 25 amps • 110V/50Hz, 25 amps

Electric Control

• 220V/50Hz, 13 amps

electric Powered console (Nor-Ht230)

Model NumberMotor Voltage

Electricity PowerMaximum Nameplate

Current

Maximum Advance Pressure

Pressure @15 Amp Motor Current (with 80° F - 100° F Oil

Temp)

Retract Pressure

NOR-HT230 230 V 50 Hz 1.5 KW 10.5 A 700 bar n/a 120 bar1 Phase 2Hp 10,150 psi n/a 1.740 psi

Hydraulic power unit engineered to continuously and reliably operate a variety of hydraulically powered torque wrenches operating up to 700 bar / 10,150 psi.

This compact design utilises a finned housing with integral fan that eliminates the need for an external cooler. Directly mounted pressure

and directional control valves eliminate additional plumbing and potential leak points while keeping the unit compact.

This unit includes pendant control for manual advance and automatic retract operation.

Model Number"Advance Flow Rate (0-100 bar / 0-1500

psi )"

"Advance Flow Rate (100-700 bar /1,500-10,1500

psi )"

Reservoir Capacity

Usable OilNoise

Level @ 300 bar

Unit Weight w/Oil

Control Pendant Length

NOR-HT230 340 in3/min 67 in3/min 3.7 Litre 1.7 Litre 68–70 dB 34 kg 6 meter

T +61 (0)8 8292 9777 | F +61 (0)8 8292 9799 | E norbar@norbar.com.au | www.norbar.com

Harsh environment range (He)Norbar has developed a range of measurement and calibration equipment that has been tested to conform with EN 60529: 1992.

Rated to IP65/IP67 the products are aimed specifically for use in harsh environments.

Particularly suited for use in the Offshore and Power Generation industries, the combination of high quality components, sound design and many years field experience allow calibration and control in previously restrictive areas.

The IP65/IP67 rating gives the product protection against dust ingression, pressurised water jet and complete water immersion to a 1 metre depth for a 30 minute period.

The HE range provides a fully traceable system to National calibration standards through Norbar’s own UKAS accredited laboratory.

Harsh Environment Instrument in water tight carry case.

5000 N.m Static Transducer

Back panel. Two connector covers removed for illustration.

Key features• IP65/67 rated.• Stainless steel transducer design with ‘SMART’ intelligence.• Bi-direction calibration for both instrument and transducer.• Class 1 accuracy over the ‘Primary’ classification range (+/-0.5% of reading

from 20 to 100% of full scale).• Battery power for use in harsh environments (mains supply for

charging).• Continuous RS-232 output.• Analogue output.• Limit indication for up to 8 user defined target values. • HE transducers are available in both static and annular

transducer designs.• Supplied in a water tight carry case.

He transducersPart No. Description

50736.xxx 500 N.m Static Transducer 3/4” M/F sq. dr.

50737.xxx 500 lbf.ft Static Transducer 3/4” M/F sq. dr.

50738.xxx 1000 N.m Static Transducer 1” M/F sq. dr.

50739.xxx 1000 lbf.ft Static Transducer 1” M/F sq. dr.

50751.xxx 3000 N.m Static Transducer 11/2” M/M sq. dr.

50705.xxx 5000 N.m Static Transducer 11/2” M/F sq. dr.

50729.xxx 5000 N.m Static Transducer 11/2” M/M sq. dr.

50706.xxx 5000 lbf.ft Static Transducer 11/2” M/F sq. dr.

50730.xxx 5000 lbf.ft Static Transducer 11/2” M/M sq. dr.

50728.xxx 10000 N.m Static Transducer 21/2” M/F sq. dr.

50726.xxx 25000 N.m Static Transducer 31/2” M/M sq. dr.

50727.xxx 40000 N.m Static Transducer 31/2” M/M sq. dr.

50744.xxx 100000 N.m Static Transducer 31/2” M/M sq. dr.

50743.xxx 100000 lbf.ft Static Transducer 31/2” M/M sq. dr.

50767.xxx 1000 N.m Annular Transducer

50745.xxx 3500 N.m Annular Transducer

50725.xxx 10000 N.m Annular TransducerOther Transducers available on request.

He Instrument and ancillariesPart No. Description

43217 TTL-HE instrument

60245.200 HE transducer Lead

60250.200 HE Inst to Standard Smart Static TD Lead

60263.200 HE Inst to Standard Smart Rotary TD Lead

60266.200 HE Transducer to TTT/TST Lead

60256.200 Serial Data Lead for TTL-HE to no connector

60257.200 Ancillaries output lead for TTL-HE to no connector

Introduction

91

Hydraulic tool calibration FixturesNorbar’s Hydraulic Tool Calibration Fixture is a robust device that allows accurate testing of hydraulic torque wrenches. A system comprises of a Calibration Fixture and Transducer from the tables below. Also required is a torque measuring instrument, see pages 76 - 81 and transducer cable, see page 86.

• Bearing support for transducer gives improved accuracy.• Interchangeable stainless steel square and round reaction posts.• Hardened steel inserts to locate reaction posts in two positions: suits most hydraulic

wrenches.• Optimised material sections for robust but portable design.• For hexagon link wrenches, a wide range of hexagon to square adaptors is available. Contact Norbar for information.

aPI Intervention tool test PotsThese reaction pots allow for the accurate testing of API rotary intervention tools.• Conform to ISO 13628-8:2002(E).• Customer specific solutions also available.• Lightweight all aluminium construction.• Incorporated lifting handles.• Eye bolts provided on larger units• Optional deck mount kit available, Part No. 81018..

Class 4 Intervention Tool Test Pot Kit includes: Pot, TTL-HE instrument, HE Transducer, Transducer lead and waterproof case.

80021 with Transducer fitted.

Hydraulic tool calibration FixturesPart No. Capacity

Square Drive

80021 7000 N.m 11/2”

80022 50000 N.m 21/2”

80023 80000 N.m 31/2”

Sleeve adaptorsPart No. Male Square

Female Square

Max Torque

86034.4 11/2” 3/4” 1200 N.m

21214 11/2” 1” 3500 N.m

29617 21/2” 11/2” 10500 N.m

29618 31/2” 21/2” 50000 N.m

transducersPart No. Description For use with

50703.xxx 250 - 2500 N.m 11/2” sq. dr. 80021

50704.xxx 250 - 2500 lbf.ft 11/2” sq. dr. 80021

50599.xxx 500 - 5000 N.m 11/2” sq. dr. 80021

50630.xxx 500 - 5000 lbf.ft 11/2” sq. dr.. 80021

50669.xxx 700 - 7000 N.m 11/2” sq. dr.. 80021

50776.xxx 1000 - 10000 N.m 21/2” sq. dr. 80022

50777.xxx 1000 - 10000 lbf.ft 21/2” sq. dr. 80022

50778.xxx 2500 - 25000 N.m 21/2” sq. dr. 80022

50779.xxx 2500 - 25000 lbf.ft 21/2” sq. dr.. 80022

50780.xxx 3000 - 30000 lbf.ft 21/2” sq. dr. 80022

50781.xxx 5000 - 50000 N.m 21/2” sq. dr. 80022

50782.xxx 6000 - 60000 lbf.ft 31/2” sq. dr. 80023

50783.xxx 8000 - 80000 N.m 31/2” sq. dr. 80023Harsh Environment Transducers available on request.

Test Pots and KitsPart No. Description

80019 Class 4 Pot

60278.xxx Class 4 Kit

80020 Class 7 Short Pot*

60279.xxx Class 7 Short Kit** FMC. Receptacle to suit ‘short’ FMC style Class 7 rotary torque intervention tools.

T +61 (0)8 8292 9777 | F +61 (0)8 8292 9799 | E norbar@norbar.com.au | www.norbar.com