· Web viewStore products in manufacturer's unopened packaging until ready for installation. Store and dispose of solvent-based materials, and materials used with solvent-based materials,

SECTION 09 91 23PAINT

Display hidden notes to specifier. (Don't know how? Click Here)

Copyright 2007 - 2015 ARCAT, Inc. - All rights reserved

1 GENERAL

1.1 SECTION INCLUDES

1.1.1 Exterior Paint.

1.1.2 Interior Paint.

1.1.3 Wall Preparation.

1.2 RELATED SECTIONS

1.2.1 Section 03 30 00 - Cast-in-Place Concrete.

1.2.2 Section 03 41 16 - Precast Concrete Slabs.

1.2.3 Section 04 40 00 - Stone Assemblies.

1.2.4 Section 05 50 00 - Metal Fabrications.

1.2.5 Section 05 70 00 - Decorative Metal.

1.2.6 Section 06 20 00 - Finish Carpentry.

1.2.7 Section 07 46 33 - Plastic Siding.

1.2.8 Section 09 20 00 - Plaster and Gypsum Board.

1.3 REFERENCES

1.3.1 ASTM International (ASTM):1.3.1.1 ASTM D 16 - Standard Terminology for Paint, Coatings, Materials, and

Applications.1.3.1.2 ASTM D 412 - Standard Test Methods for Vulcanized Rubber and Thermoplastic

Elastomers - Tension.

09 91 23-1

1.3.1.3 ASTM D 522 - Standard Test Methods for Mandrel Bend Test of Attached Organic Coatings.

1.3.1.4 ASTM D 4442 - Standard Test Methods for Direct Moisture Content Measurement of Wood and Wood-Base Materials.

1.3.2 Green Seal Standard GS-11; May 20, 1993.

1.3.3 MPI (APL) - Master Painters Institute.

1.3.4 SSPC (PM1) - Steel Structures Painting Manual, Vol. 1, Good Painting Practice; Society for Protective Coatings; 1993, Third Edition.

1.3.5 SSPC (PM2) - Steel Structures Painting Manual, Vol. 2, Systems and Specifications; Society for Protective Coatings; 1995, Seventh Edition.

1.3.6 40 CFR 59, Subpart D - National Volatile Organic Compound Emission Standards for Architectural Coatings; U.S. Environmental Protection Agency; current edition.

1.4 DEFINITIONS

1.4.1 Products manufactured by Miller Paint Company are available in a wide range of glosses, as measured by a gloss meter from a 60 degree angle from vertical, as a percentage of the amount of light that is reflected. The following terms are used by Miller Paint to describe the gloss of our products.1.4.1.1 Flat - Less than 5 Percent; Less than 5 percent at 85 degrees.1.4.1.2 Velvet - Less than 5 Percent; 4 to 20 percent at 85 degrees.1.4.1.3 Eggshell - 5 - 10 Percent; 4 to 20 percent at 85 degrees.1.4.1.4 Satin - 10 - 20 Percent.1.4.1.5 Semi-Gloss - 35 - 55 Percent.1.4.1.6 Gloss - 75 - 90 Percent.

1.5 SUBMITTALS

1.5.1 Submit under provisions of Section 01 30 00.

1.5.2 Coordinate with Section 01 30 00 - Administrative Requirements.

1.5.3 LEED Certification Product Data:1.5.3.1 See Section 01 11 13 - Work Covered by Contract Documents.1.5.3.2 Submittals Required:

1.5.3.2.1 MRc3 Resource Reuse (LEED Form).1.5.3.2.2 MRc4 Recycled Content (LEED Form).1.5.3.2.3 MRc5 Local and Regional Materials (LEED Form).1.5.3.2.4 EQc4.1 Low Emitting Materials - Adhesives and Solvents (VOC

Certification Letter).1.5.3.2.5 EQc4.2 Low Emitting Materials - Paint (VOC Certification Letter).1.5.3.2.6 Green Seal Standard GS-11 Certified Product certificates.

1.5.4 Product Data: Provide complete list of all products to be used, with the following information for each:1.5.4.1 Manufacturer's name, product name and/or catalog number, and general product

category (e.g. "alkyd enamel").1.5.4.2 Cross-reference to specified paint system(s) product is to be used in; include

description of each system.

1.5.5 Samples: Submit three paper "drop" samples, 5 inches by 7 inches (127mm x 178mm) in size, illustrating selected colors for each color and system selected with specified coats cascaded.

09 91 23-2

1.5.5.1 Where sheen is specified, submit samples in only that sheen.1.5.5.2 Opaque Finishes: Furnish samples of each color and material in quantities

described above, with texture to simulate actual conditions. Resubmit each sample as requested until required sheen, color and texture are achieved.

1.5.5.3 Transparent Finishes: On specified wood surfaces, provide two 12 inch by 12 inch (305mm x 305mm) samples of each natural / stained finish as required.

1.5.6 Manufacturer's Certification: Provide signed letter from the paint manufacturer certifying that products provided meet or exceed the specified requirements of this section.

1.5.7 Manufacturer's Instructions: Indicate special surface preparation procedures.

1.5.8 Maintenance Data: Submit data on cleaning, touch-up, and repair of painted and coated surfaces.

1.6 QUALITY ASSURANCE

1.6.1 Manufacturer Qualifications: All primary products specified in this section will be supplied by a single manufacturer with a minimum of ten (10) years experience.

1.6.2 Installer Qualifications: All products listed in this section are to be installed by a single installer with a minimum of five (5) years demonstrated experience in installing products of the same type and scope as specified.

1.6.3 Mock-Up: Provide a mock-up for evaluation of surface preparation techniques and application workmanship.1.6.3.1 Finish areas designated by Architect.1.6.3.2 Do not proceed with remaining work until workmanship, color, and sheen are

approved by Architect.1.6.3.3 Refinish mock-up area as required to produce acceptable work.

1.6.4 Previously Painted Surfaces Contaminated with Lead Paint: Strictly comply with local and federal regulations regarding previously painted surfaces contaminated with lead paint.

1.7 DELIVERY, STORAGE, AND HANDLING

1.7.1 Store products in manufacturer's unopened packaging until ready for installation.

1.7.2 Store and dispose of solvent-based materials, and materials used with solvent-based materials, in accordance with requirements of local authorities having jurisdiction.

1.8 PROJECT CONDITIONS

1.8.1 Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's absolute limits.

1.9 WARRANTY

1.9.1 At project closeout, provide to the Owner or owner's representative an executed copy of the Manufacturer's standard form outlining the terms and conditions of and any exclusions to their Limited Warranty against Manufacturing Defect.

1.10 EXTRA MATERIALS

1.10.1 At project closeout, supply the Owner or owner's representative one gallon of each product for touch-up purposes.

09 91 23-3

1.10.2 At project closeout, provide the color mixture name and code to the Owner or owner's representative for accurate future color matching.

2 PRODUCTS

2.1 MANUFACTURERS

2.1.1 Acceptable Manufacturer: Miller Paint Co., which is located at: 12812 N. E. Whitaker Way; Portland, OR 97230; Toll Free Tel: 800-852-3254; Tel: 503-255-0190; Fax: 503-255-0192; Email:[email protected]; Web:www.millerpaint.com|www.thecolorevolution.com

2.1.2 Substitutions: Not permitted.

2.1.3 Requests for substitutions will be considered in accordance with provisions of Section 01 60 00.

2.2 LEED CRITERIA

2.2.1 All paints and coatings used on site shall meet VOC limits:2.2.1.1 Interior: 100 g/l VOC or less with colorant added at the point of sale for Flats and

150 g/l VOC or less with colorant added at the point of sale for Non Flats and Primers per Green Seal Standard GS-11.

2.2.1.2 Exterior: 100 g/l VOC for Flats and 200 g/l VOC or Less for Non Flats per Green Seal Standard GS-11.

2.2.1.3 Anti-Corrosive Paints: 250 g/l VOC per Green Seal Standard GC-03 Anti-Corrosive Paints,2nd Edition, January 7, 1997.

2.2.1.4 Stains, Clear Wood Finishes and Sealers: Waterproofing Sealers - less than 250 g/L; Sanding Sealers - less than 275 g/L; all other sealers - less than 200 g/L per South Coast Air Quality Management District (SCAQMD) Rule 1113,Architectural Coatings, rules in effect on January 1, 2004.

2.3 MATERIALS - GENERAL

2.3.1 Volatile Organic Compound (VOC) Content:2.3.1.1 Provide coatings that comply with the most stringent requirements specified in

the following:2.3.1.1.1 40 CFR 59, Subpart D-National Volatile Organic Compound Emission

Standards for Architectural Coatings.2.3.1.2 Determination of VOC Content: Testing and calculation in accordance with 40

CFR 59, Subpart D (EPA Method 24), exclusive of colorants added to a tint base and water added at project site; or other method acceptable to authorities having jurisdiction.

2.3.2 Paints and Coatings:2.3.2.1 Provide ready mixed paints and coatings, except field-catalyzed coatings.2.3.2.2 Provide materials that are compatible with one another and the substrates

indicated under conditions of service and application, as demonstrated by manufacturer based on testing and field experience.

2.4 EXTERIOR SURFACES

2.4.1 Brick, Concrete and Masonry:2.4.1.1 Primer: Kril Primer Sealer - 6040 - Water Based.

2.4.1.1.1 Finish: Low sheen.2.4.1.2 Finish Coat: Evolution Satin Exterior Paint - 8600 - Water Based.

2.4.1.2.1 Finish: Satin.

09 91 23-4

2.4.1.3 Finish Coat: Evolution Velvet Exterior Paint - 8900 - Water Based.2.4.1.3.1 Finish: Velvet.

2.4.1.4 Finish Coat: Evolution Flat Exterior Paint - 8500 - Water Based.2.4.1.4.1 Finish: Flat.

2.4.1.5 Finish Coat: Acri-Lite Semi-gloss Exterior Paint - 7500 - Water Based.2.4.1.5.1 Finish: Semi-gloss.

2.4.1.6 Finish Coat: Acri-Lite Satin Exterior Paint - 7400 - Water Based.2.4.1.6.1 Finish: Satin.

2.4.1.7 Finish Coat: Acri-Lite Velvet Exterior Paint - 7000 - Water Based.2.4.1.7.1 Finish: Velvet.

2.4.1.8 Finish Coat: Acri-Lite Flat Exterior Paint - 6900 - Water Based.2.4.1.8.1 Finish: Flat.

2.4.1.9 Finish Coat: Krill Semi-Gloss Exterior Paint - 5500 - Water Based.2.4.1.9.1 Finish: Semi-gloss.

2.4.1.10 Finish Coat: Krill Satin Exterior Paint - 5600 - Water Based.2.4.1.10.1 Finish: Satin.

2.4.1.11 Finish Coat: Krill Velvet Exterior Paint - 5700 - Water Based.2.4.1.11.1 Finish: Velvet.

2.4.1.12 Finish Coat: Krill Flat Exterior Paint - 5900 - Water Based.2.4.1.12.1 Finish: Flat.

2.4.1.13 Finish Coat: Milastic Elastomeric Coating - 8800 - Water Based Elastomeric.2.4.1.13.1 Finish: Velvet.

2.4.2 Concrete Block:2.4.2.1 Primer/Filler: Block Filler - 6015 - Water Based.2.4.2.2 Finish Coat: Evolution Satin Exterior Paint - 8600 - Water Based.

2.4.2.2.1 Finish: Satin.2.4.2.3 Finish Coat: Evolution Velvet Exterior Paint - 8900 - Water Based.

2.4.2.3.1 Finish: Velvet.2.4.2.4 Finish Coat: Evolution Flat Exterior Paint - 8500 - Water Based.

2.4.2.4.1 Finish: Flat.2.4.2.5 Finish Coat: Acri-Lite Semi-gloss Exterior Paint - 7500 - Water Based.

2.4.2.5.1 Finish: Semi-gloss.2.4.2.6 Finish Coat: Acri-Lite Satin Exterior Paint - 7400 - Water Based.

2.4.2.6.1 Finish: Satin.2.4.2.7 Finish Coat: Acri-Lite Velvet Exterior Paint - 7000 - Water Based.

2.4.2.7.1 Finish: Velvet.2.4.2.8 Finish Coat: Acri-Lite Flat Exterior Paint - 6900 - Water Based.

2.4.2.8.1 Finish: Flat.2.4.2.9 Finish Coat: Krill Semi-Gloss Exterior Paint - 5500 - Water Based.

2.4.2.9.1 Finish: Semi-gloss.2.4.2.10 Finish Coat: Krill Satin Exterior Paint - 5600 - Water Based.

2.4.2.10.1 Finish: Satin.2.4.2.11 Finish Coat: Krill Velvet Exterior Paint - 5700 - Water Based.

2.4.2.11.1 Finish: Velvet.2.4.2.12 Finish Coat: Krill Flat Exterior Paint - 5900 - Water Based.

2.4.2.12.1 Finish: Flat.2.4.2.13 Finish Coat: Milastic Elastomeric Coating - 8800 - Water Based Elastomeric.

2.4.2.13.1 Finish: Velvet.

2.4.3 Wood Siding and Trim, Plywood, Texture 111:2.4.3.1 Primer: Kril Primer Sealer - 6040 - Water Based.

2.4.3.1.1 Finish: Low sheen.2.4.3.2 Primer: Pure Paint Primer - 240 - Solvent Based.2.4.3.3 Primer: Miller Prime 6060 All Purpose Acrylic Stain Blocking Primer.2.4.3.4 Finish Coat: Evolution Satin Exterior Paint - 8600 - Water Based.

09 91 23-5











2.4.3.14.1 Finish: Flat.

2.4.4 Cement / Fiber Siding and Hardboard Siding:2.4.4.1 Finish Coat: Evolution Satin Exterior Paint - 8600 - Water Based.












2.4.5 Woodwork, Doors and Finish Grade Trim, Enamel Finish:2.4.5.1 Primer: Pure Paint Primer - 240 - Solvent Based.2.4.5.2 Primer: Miller Prime 6060 All Purpose Acrylic Stain Blocking Primer.2.4.5.3 Finish Coat: Acrinamel Gloss Paint - 7300 - Water Based.

2.4.5.3.1 Finish: Gloss.2.4.5.4 Finish Coat: Acrinamel Semi-Gloss Paint - 7200 - Water Based.

2.4.5.4.1 Finish: Semi-gloss.2.4.5.5 Finish Coat: Acrinamel Satin Paint - 7100 - Water Based.

2.4.5.5.1 Finish: Satin.2.4.5.6 Finish Coat: Premium Spar Enamel - 2510 - Solvent Based.

09 91 23-6

2.4.5.6.1 Finish: Gloss.

2.4.6 Woodwork, Doors and Finish Grade Trim, Clear Varnish Finish:2.4.6.1 Finish Coat: Ultraviolet Shield Spar Varnish - 1209 - Solvent Based.


2.4.7 Wood Floors and Porches:2.4.7.1 Finish Coat: Tuff Tread - 280 - Water Based.2.4.7.2 Finish Coat: Floor and Porch Enamel - 2250 - Solvent Based.

2.4.7.2.1 Finish: Semi-Gloss.

2.4.8 Metal - Ferrous: Enamel finishes.2.4.8.1 Primer: Rust Control Primer - 468 - Solvent Based, brush applied.

2.4.8.1.1 Color: Red Oxide.2.4.8.1.2 Finish: Flat.

2.4.8.2 Primer: Brushable Metal Primer - 470 - Solvent Based, brush applied.2.4.8.2.1 Color: White.2.4.8.2.2 Color: Gray.2.4.8.2.3 Finish: Flat.

2.4.8.3 Primer: Premium Metal Primer - 363, spray applied.2.4.8.3.1 Color: Red Oxide.2.4.8.3.2 Finish: Flat.

2.4.8.4 Primer: Aluminum and Ferrous Metal Primer - 484, spray applied.2.4.8.4.1 Color: White.2.4.8.4.2 Finish: Low sheen.

2.4.8.5 Primer: Gray Quick Dry Metal Primer - 358, spray applied.2.4.8.5.1 Color: Gray.2.4.8.5.2 Finish: Flat.

2.4.8.6 Primer / Finish (Direct to Metal): Acrimetal DTM - 5000 - Water Based.2.4.8.6.1 Finish: Velvet.

2.4.8.7 Primer / Finish (Direct to Metal): Acrimetal DTM - 5200 - Water Based.2.4.8.7.1 Finish: Semi-Gloss.

2.4.8.8 Primer / Finish (Direct to Metal): Acrimetal DTM - 5300 - Water Based.2.4.8.8.1 Finish: Gloss.

2.4.8.9 Finish: Synthetic Equipment Enamel - 3000.2.4.8.9.1 Finish: Gloss.

2.4.8.10 Finish Coat: Acrinamel Gloss Paint - 7300 - Water Based.2.4.8.10.1 Finish: Gloss.

2.4.8.11 Finish Coat: Acrinamel Semi-Gloss Paint - 7200 - Water Based.2.4.8.11.1 Finish: Semi-gloss.

2.4.8.12 Finish Coat: Acrinamel Satin Paint - 7100 - Water Based.2.4.8.12.1 Finish: Satin.

2.4.8.13 Finish Coat: Premium Spar Enamel - 2510 - Solvent Based.2.4.8.13.1 Finish: Gloss.

2.4.8.14 Finish Coat: Premium Alkyd Enamel - Semi-Gloss - 6750 - Solvent Based.2.4.8.14.1 Finish: Semi-Gloss.

2.4.8.15 Finish Coat: Premium Alkyd Enamel - Satin - 6850 - Solvent Based.2.4.8.15.1 Finish: Satin.

2.4.9 Metal - Non-Ferrous and Galvanized; Enamel Finishes:2.4.9.1 Primer: Aluminum and Ferrous Metal Primer - 484, Solvent Based.2.4.9.2 Primer / Finish (Direct to Metal): Acrimetal DTM - 5000 - Water Based.

2.4.9.2.1 Finish: Velvet.2.4.9.3 Primer / Finish (Direct to Metal): Acrimetal DTM - 5100 Water Based.

2.4.9.3.1 Finish: Satin.2.4.9.4 Primer / Finish (Direct to Metal): Acrimetal DTM - 5200 - Water Based.

09 91 23-7

2.4.9.4.1 Finish: Semi-Gloss.2.4.9.5 Primer / Finish (Direct to Metal): Acrimetal DTM - 5300 - Water Based.

2.4.9.5.1 Finish: Gloss.2.4.9.6 Finish: Synthetic Equipment Enamel - 3000.

2.4.9.6.1 Finish: Gloss.2.4.9.7 Finish Coat: Acrinamel Gloss Paint - 7300 - Water Based.




2.4.9.10.1 Finish: Gloss.2.4.9.11 Finish Coat: Premium Alkyd Enamel - Semi-Gloss - 6750 - Solvent Based.

2.4.9.11.1 Finish: Semi-Gloss.2.4.9.12 Finish Coat: Premium Alkyd Enamel - Satin - 6850 - Solvent Based.


2.5 INTERIOR SURFACES

2.5.1 Brick, Concrete, and Masonry:2.5.1.1 Primer: Kril Primer Sealer - 6040 - Water Based.

2.5.1.1.1 Finish: Low sheen.2.5.1.2 Primer/Filler: Block Filler - 6015 - Water Based.2.5.1.3 Finish Coat: Acro PURE Semi-gloss Interior Paint - 2850 - Water Based.

2.5.1.3.1 Finish: Semi-gloss.2.5.1.4 Finish Coat: Acro PURE Satin Interior Paint - 1450 - Water Based.

2.5.1.4.1 Finish: Satin.2.5.1.5 Finish Coat: Acro PURE Eggshell Interior Paint - 4650 - Water Based.

2.5.1.5.1 Finish: Eggshell.2.5.1.6 Finish Coat: Acro PURE Flat Interior Paint - 6450 - Water Based.

2.5.1.6.1 Finish: Flat.2.5.1.7 Finish Coat: Premium Semi-Gloss Interior Paint - 4580 - Water Based.

2.5.1.7.1 Finish: Semi-gloss.2.5.1.8 Finish Coat: Premium Satin Interior Paint - 4480 - Water Based.

2.5.1.8.1 Finish: Satin.2.5.1.9 Finish Coat: Premium Eggshell Interior Paint - 3880 - Water Based.

2.5.1.9.1 Finish: Eggshell.2.5.1.10 Finish Coat: Premium Flat Interior Paint - 3780 - Water Based.

2.5.1.10.1 Finish: Flat.2.5.1.11 Finish Coat: Performance Semi-gloss Interior Paint - 8480 - Water Based.

2.5.1.11.1 Finish: Semi-gloss.2.5.1.12 Finish Coat: Performance Satin Interior Paint - 8380 - Water Based.

2.5.1.12.1 Finish: Satin.2.5.1.13 Finish Coat: Performance Eggshell Interior Paint - 8280 - Water Based.

2.5.1.13.1 Finish: Eggshell.2.5.1.14 Finish Coat: Performance Flat Interior Paint - 8180 - Water Based.

2.5.1.14.1 Finish: Flat.2.5.1.15 Finish Coat: Acrinamel Gloss Paint - 7300 - Water Based.



2.5.1.17.1 Finish: Satin.2.5.1.18 Finish Coat: Performance Plus Flat 130110.


09 91 23-8

2.5.1.19 Finish Coat: Performance Plus Eggshell 130310.2.5.1.19.1 Finish: Eggshell.

2.5.1.20 Finish Coat: Performance Plus Satin 130410.2.5.1.20.1 Finish: Satin.

2.5.1.21 Finish Coat: Performance Plus Semi-gloss 130510.2.5.1.21.1 Finish: Semi-gloss.

2.5.1.22 Finish Coat: Premium Oil Based Spar Enamel - 2510 - Solvent Based.2.5.1.22.1 Finish: Gloss.



2.5.1.25 Finish Coat: Evolution Paper Wall Finish - 1001 - Water Based.2.5.1.25.1 Finish: Matte.

2.5.1.26 Finish Coat: Evolution Canvas Wall Paint - 1003 - Water Based.2.5.1.26.1 Finish: Eggshell.

2.5.1.27 Finish Coat: Evolution Silk Wall Paint - 1004 - Water Based.2.5.1.27.1 Finish: Satin.

2.5.1.28 Finish Coat: Evolution Frame Trim Paint - 1005 - Water Based.2.5.1.28.1 Finish Coat: Semi-gloss.

2.5.1.29 Finish Coat: High Build Paint - 9097 - Water Based.2.5.1.29.1 Finish Coat: Eggshell.

2.5.1.30 Finish Coat: Epoxy - 4200 - Water Based.2.5.1.30.1 Finish Coat: Semi-gloss.

2.5.1.31 Finish Coat: Epoxy - 4300 - Water Based.2.5.1.31.1 Finish Coat: Gloss.

2.5.2 Concrete Block:2.5.2.1 Primer/Filler: Block Filler - 6015 - Water Based.2.5.2.2 Finish Coat: Acro PURE Semi-gloss Interior Paint - 2850 - Water Based.








2.5.2.9.1 Finish: Flat.2.5.2.10 Finish Coat: Performance Semi-gloss Interior Paint - 8480 - Water Based.






09 91 23-9


2.5.2.16.1 Finish: Satin.2.5.2.17 Finish Coat: Premium Oil Based Spar Enamel - 2510 - Solvent Based.

2.5.2.17.1 Finish: Gloss.2.5.2.18 Finish Coat: Performance Plus Flat 130110.

2.5.2.18.1 Finish: Flat.2.5.2.19 Finish Coat: Performance Plus Eggshell 130310.

2.5.2.19.1 Finish: Eggshell.2.5.2.20 Finish Coat: Performance Plus Satin 130410.

2.5.2.20.1 Finish: Satin.2.5.2.21 Finish Coat: Performance Plus Semi-gloss 130510.

2.5.2.21.1 Finish: Semi-gloss.2.5.2.22 Finish Coat: Premium Alkyd Enamel - Semi-Gloss - 6750 - Solvent Based.


2.5.2.23.1 Finish: Satin.2.5.2.24 Finish Coat: Evolution Paper Wall Finish - 1001 - Water Based.

2.5.2.24.1 Finish: Matte.2.5.2.25 Finish Coat: Evolution Canvas Wall Paint - 1003 - Water Based.

2.5.2.25.1 Finish: Eggshell.2.5.2.26 Finish Coat: Evolution Silk Wall Paint - 1004 - Water Based.

2.5.2.26.1 Finish: Satin.2.5.2.27 Finish Coat: Evolution Frame Trim Paint - 1005 - Water Based.

2.5.2.27.1 Finish Coat: Semi-gloss.2.5.2.28 Finish Coat: High Build Paint - 9097 - Water Based.

2.5.2.28.1 Finish Coat: Eggshell.2.5.2.29 Finish Coat: Epoxy - 4200 - Water Based.

2.5.2.29.1 Finish Coat: Semi-gloss.2.5.2.30 Finish Coat: Epoxy - 4300 - Water Based.

2.5.2.30.1 Finish Coat: Gloss.

2.5.3 Plaster and Gypsum Wallboard:2.5.3.1 Primer: Kril Primer Sealer - 6040.

2.5.3.1.1 Finish: Low sheen.2.5.3.2 Primer: Super Seal - 4740 - Water borne.

2.5.3.2.1 Finish: Low sheen.2.5.3.3 Primer: Acro Pure Primer - 6440 - Water borne.

2.5.3.3.1 Finish: Flat.2.5.3.4 Primer: Premium PVA - 6020 - Water borne.

2.5.3.4.1 Finish: Low sheen.2.5.3.5 Primer: Performance Plus Primer 130010.

2.5.3.5.1 Finish: Flat.2.5.3.6 Primer: Performance PVA - 8140 - Water borne.

2.5.3.6.1 Finish: Velvet.2.5.3.7 Finish Coat: Acro PURE Semi-gloss Interior Paint - 2850 - Water Based.






09 91 23-10



2.5.3.14.1 Finish: Flat.2.5.3.15 Finish Coat: Performance Semi-Gloss Interior Paint - 8480 - Water Based.







2.5.3.21.1 Finish: Satin.2.5.3.22 Finish Coat: Performance Plus Flat 130110.

2.5.3.22.1 Finish: Flat.2.5.3.23 Finish Coat: Performance Plus Eggshell 130310.

2.5.3.23.1 Finish: Eggshell.2.5.3.24 Finish Coat: Performance Plus Satin 130410.

2.5.3.24.1 Finish: Satin.2.5.3.25 Finish Coat: Performance Plus Semi-gloss 130510.

2.5.3.25.1 Finish: Semi-gloss.2.5.3.26 Finish Coat: Premium Alkyd Enamel - Semi-Gloss - 6750 - Solvent Based.


2.5.3.27.1 Finish: Satin.2.5.3.28 Finish Coat: Premium Oil Based Spar Enamel - 2510 - Solvent Based.

2.5.3.28.1 Finish: Gloss.2.5.3.29 Finish Coat: Evolution Paper Wall Finish - 1001 - Water Based.

2.5.3.29.1 Finish: Matte.2.5.3.30 Finish Coat: Evolution Canvas Wall Paint - 1003 - Water Based.

2.5.3.30.1 Finish: Eggshell.2.5.3.31 Finish Coat: Evolution Silk Wall Paint - 1004 - Water Based.

2.5.3.31.1 Finish: Satin.2.5.3.32 Finish Coat: Evolution Frame Trim Paint - 1005 - Water Based.

2.5.3.32.1 Finish Coat: Semi-gloss.2.5.3.33 Finish Coat: High Build Paint - 9097 - Water Based.

2.5.3.33.1 Finish Coat: Eggshell.2.5.3.34 Finish Coat: Epoxy - 4200 - Water Based.

2.5.3.34.1 Finish Coat: Semi-gloss.2.5.3.35 Finish Coat: Epoxy - 4300 - Water Based.

2.5.3.35.1 Finish Coat: Gloss.

2.5.4 Woodwork, Doors and Trim, Enamel Finishes:2.5.4.1 Primer: Acrylic Enamel Undercoat - 2840 - Water Based.2.5.4.2 Finish Coat: Acrinamel Gloss Paint - 7300 - Water Based.




09 91 23-11

2.5.4.5 Finish Coat: Premium Spar Enamel - 2510 - Solvent Based, Brush applied only.2.5.4.5.1 Finish: Gloss.

2.5.4.6 Finish Coat: Premium Alkyd Enamel - Semi-Gloss - 6750 - Solvent Based, Brush applied only.

2.5.4.6.1 Finish: Semi-Gloss.2.5.4.7 Finish Coat: Premium Alkyd Enamel - Satin - 6850 - Solvent Based, Brush

applied only.2.5.4.7.1 Finish: Satin.

2.5.4.8 Finish Coat: Synthetic Equipment Enamel - 3000 - Solvent Based, Spray applied only.


2.5.5 Woodwork, Doors and Trim - Clear and Stained Finishes:2.5.5.1 Stain: Acriclear Stain - 1228 - Water Based.

2.5.5.1.1 Finish: Semi Transparent.2.5.5.2 Stain: Modern Wood Stain - 700 - Solvent Based.

2.5.5.2.1 Finish: Flat.2.5.5.3 Primer / Sealer: Acriclear Sanding Sealer - 1220 - Water Based.

2.5.5.3.1 Finish: Satin.2.5.5.4 Primer / Sealer: Miller Seal - 1206 - Solvent Based.

2.5.5.4.1 Finish: Satin.2.5.5.5 Finish Coat: Acriclear Varnish - Gloss Finish - 1221 - Water Based.2.5.5.6 Finish Coat: Acriclear Varnish - Semi-Gloss Finish - 1226 - Water Based.2.5.5.7 Finish Coat: Acriclear Varnish - Satin Finish - 1225 - Water Based.2.5.5.8 Finish Coat: Acriclear Varnish - Matte Finish - 1223 - Water Based.2.5.5.9 Finish Coat: Polyurethane Clear - Gloss Finish - 1283 - Solvent Based.2.5.5.10 Finish Coat: Polyurethane Clear - Satin Finish - 1281 - Solvent Based.2.5.5.11 Finish Coat: Polyurethane Clear - Matte Finish - 1280 - Solvent Based.

2.5.6 Wood Floors:2.5.6.1 Finish Coat: Gym Coat - 1263 - Solvent Based.


2.5.7 Floors; Concrete and Wood Enamel Finish:2.5.7.1 Finish Coat: Tuff Tread - 280 - Water Based.

2.5.7.1.1 Finish - Velvet.2.5.7.2 Finish - Floor & Porch Enamel - 2250 - Solvent Based.

2.5.7.2.1 Finish - Semi-Gloss.

2.5.8 Metal - Ferrous: Enamel finishes.2.5.8.1 Primer: Rust Control Primer - 468 - Solvent Based, brush applied.

2.5.8.1.1 Color: Red Oxide.2.5.8.1.2 Finish: Flat.

2.5.8.2 Primer: Brushable Metal Primer - 470 - Solvent Based, brush applied.2.5.8.2.1 Color: White.2.5.8.2.2 Color: Gray.2.5.8.2.3 Finish: Flat.

2.5.8.3 Primer: Premium Metal Primer - 363, spray applied.2.5.8.3.1 Color: Red Oxide.2.5.8.3.2 Finish: Flat.

2.5.8.4 Primer: Aluminum and Ferrous Metal Primer - 484, spray applied.2.5.8.4.1 Color: White.2.5.8.4.2 Finish: Low sheen.

2.5.8.5 Primer: Gray Quick Dry Metal Primer - 358, spray applied.2.5.8.5.1 Color: Gray.2.5.8.5.2 Finish: Flat.

09 91 23-12

2.5.8.6 Primer / Finish (Direct to Metal): Acrimetal DTM - 5000 - Water Based.2.5.8.6.1 Finish: Velvet.

2.5.8.7 Primer / Finish (Direct to Metal): Acrimetal DTM - 5100 - Water Based.2.5.8.7.1 Finish: Satin.

2.5.8.8 Primer / Finish (Direct to Metal): Acrimetal DTM - 5200 - Water Based.2.5.8.8.1 Finish: Semi-Gloss.

2.5.8.9 Primer / Finish (Direct to Metal): Acrimetal DTM - 5300 - Water Based.2.5.8.9.1 Finish: Gloss.

2.5.8.10 Finish: Synthetic Equipment Enamel - 3000.2.5.8.10.1 Finish: Gloss.

2.5.8.11 Finish Coat: Acrinamel Gloss Paint - 7300 - Water Based.2.5.8.11.1 Finish: Gloss.

2.5.8.12 Finish Coat: Acrinamel Semi-Gloss Paint - 7200 - Water Based.2.5.8.12.1 Finish: Semi-gloss.

2.5.8.13 Finish Coat: Acrinamel Satin Paint - 7100 - Water Based.2.5.8.13.1 Finish: Satin.

2.5.8.14 Finish Coat: Premium Spar Enamel - 2510 - Solvent Based.2.5.8.14.1 Finish: Gloss.



2.5.9 Metal - Non-Ferrous and Galvanized; Enamel Finishes:2.5.9.1 Primer: Aluminum and Ferrous Metal Primer - 484, Solvent Based.2.5.9.2 Primer/Finish (Direct to Metal): Acrimetal DTM - 5000 - Water Based.

2.5.9.2.1 Finish: Velvet.2.5.9.3 Primer / Finish (Direct to Metal): Acrimetal DTM - 5100 - Water Based.

2.5.9.3.1 Finish: Satin.2.5.9.4 Primer / Finish (Direct to Metal): Acrimetal DTM - 5200 - Water Based.

2.5.9.4.1 Finish: Semi-Gloss.2.5.9.5 Primer / Finish (Direct to Metal): Acrimetal DTM - 5300 - Water Based.

2.5.9.5.1 Finish: Gloss.2.5.9.6 Finish: Synthetic Equipment Enamel - 3000.

2.5.9.6.1 Finish: Gloss.2.5.9.7 Finish Coat: Acrinamel Gloss Paint - 7300 - Water Based.




2.5.9.10.1 Finish: Gloss.2.5.9.11 Finish Coat: Premium Alkyd Enamel - Semi-Gloss - 6750 - Solvent Based.



3 EXECUTION

3.1 EXAMINATION

3.1.1 Do not begin installation until substrates have been properly prepared.

3.1.2 Inspect all surfaces for defects prior to starting Work. Notify the Architect of any damaged or otherwise inferior surfaces prior to application of finish coat.

09 91 23-13

3.1.3 If substrate preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding.

3.1.4 Prior to starting Work, test for adhesion and compatibility with existing finishes.

3.2 PREPARATION

3.2.1 Clean surfaces thoroughly prior to installation. Repair cracks and fill voids.

3.2.2 Prepare surfaces using the methods recommended by the manufacturer and the Master Painters Institute for achieving the best result for the substrate under the project conditions.

3.2.3 Remove and store all hardware and fittings prior to painting. Carefully clean and replace all such items upon completion of painting work in each area. Remove doors and other movable fixtures that require paint on all sides prior to application.

3.2.4 Wash areas where mold and mildew are present. Remove previous coatings that have poor adhesion and all dirt, oil, grease, wax and/or other contaminants. De-gloss shiny surfaces by lightly sanding.

3.3 APPLICATION

3.3.1 Apply paint with a brush, roller or airless sprayer in accordance with manufacturer's instructions and recommended coverage rates.

3.3.2 Follow manufacturer's instructions for application temperatures based on the product being applied. Keep product from freezing.

3.3.3 Dispose of excess materials in accordance with local and federal regulations.

3.4 PROTECTION

3.4.1 Protect installed products until completion of project.

3.4.2 Touch-up, damaged areas before Substantial Completion.

3.5 FINISH SCHEDULE

3.5.1 Reference: ___________________ / Description: _________________________________.3.5.1.1 Primer:

3.5.1.1.1 Material: _____________________.3.5.1.1.2 Color: ________________________.

3.5.1.2 Finish Coat:3.5.1.2.1 Material: _____________________.3.5.1.2.2 Color: ________________________.

END OF SECTION

09 91 23-14