01, Front Cover - Alamo Industrial · 2008-09-17 · Alamo Industrial ™ Technical Services Department 1502 East Walnut Seguin, Texas 78155 830-372-2708 Models: All Models using

2004 Edition

Manual P/N 02980508 (01/04)

© 2004 Alamo Group Inc.

Alamo IndustrialP. O. Drawer 549Seguin, Texas 78155830-372-3551

INFORMATION&

SERVICEBULLETINS

(All Current Production Mechanical Rotary Models)

MECHANICALROTARY


BOOK INTRODUCTIONINFORMATION & SERVICE

BULLETINSThis Book is divided into two Sections

Section One - Technical Information Bulletins

1. Technical Information Bulletins: Information Bulletins are listed by Bulletin Number (Date).Example the oldest Bulletin will be listed first and the most recent bulletin will be listed last.Bulletin No. 021002 = first & second digits are the month, the third & fourth digits are the dayof the month and the fifth & sixth digits are the year this means, the bulletin was written on Feb,10, 2002. If more than one bulletin was written on that day the a dash with a number will added,example -1, -2 etc.

2. Authorize Repairs: Technical Information Bulletins do not authorize any repairs to be madeunder warranty or any other circumstance unless specifically instructed to do so.

3. Bulletin Reference: Some Technical Information Bulletins will refer to the correspondingService Bulletins for repairs and some are for information only.

4. Bulletin Instructions: Technical Information Bulletins should have all the instructions as towhat you need, but may not have all the information needed to make an installation complete.In some cases it may be required to refer to other manuals for more complete information, thisshould be suggested in the Technical Information Bulletin.

5. All Technical Information Bulletins printed in this Manual will void any previously printed Bulletin.Any changes in these bulletins are the final version as of the date of this manual.

Section Two - Service Bulletins

1. Service Bulletin No: Service Bulletins are listed by Bulletin Number (Date). Example theoldest Bulletin will be listed first and the most recent bulletin will be listed last. Bulletin No. 021004= first & second digits are the Year, the third & fourth digits are the day of the month and the fifth& sixth digits are the month, this means the bulletin was written on Apr, 10, 2002. If more thanone bulletin was written on that day the a dash with a number will added, example -1, -2 etc.

2. Repairs: Service Bulletins are intended to authorize only the repairs listed on It to be madeunder warranty or any other circumstance unless specifically instructed to do so.

3. Parts: This is the Rate at which compensation will be allowed under warranty for repair parts.4. Labor: This is the amount of labor (hours) that are allowed to make this repair under warranty.5. Parts Disposition: Service Bulletins list the disposition of any parts that are removed during the

repair. If listed removed parts must be held awaiting return to factory if instructed to do so.6. Termination Date: Service bulletins show a termination date, this is the date that the Bulletin

will be discontinued, Any repairs must be made and all warranty applications filed by the listeddate.

7. All Service Bulletins printed in this Manual will void any previously printed Bulletin. Anychanges in these bulletins are the final version as of the date of this manual.


INDEXMECHANICAL ROTARY MODELS

Section 1 Technical Information Bulletins

INDEX - 1

Bulletin No. (Old No.) Page Date Description

----------......................... 1-1............... -----------.... Information Bulletins Introduction.040896 (040896)...........1-2............... 04/08/96.... Oil Leaking from new Hydraulic Cylinders.050697 (043097R)........ 1-3............... 04/30/97.... See 050697 for Bulletin.050697 (050697A)........ 1-3............... 05/06/97.... Springless Slip Clutch Adjustment Procedure.102398 ......................... 1-4............... 10/23/98.... "Will Fit" Clutch Disk Linings.112498.......................... 1-5............... 11/24/98.... Three Point Tractor Lift Dimensions.

© 2004 Alamo Group Inc. INDEX - 2

INDEXMECHANICAL ROTARY MODELS

Section 2Service Bulletins

Bulletin No. (Old No.) Page Date Description

----------......................... 2-1............... -----------.... Service Bulletin Introduction.922002 (92-002)........... 2-2............... 02/20/92.... Aircraft Tire and Wheel Operating Procedure.922905 (92-008)........... 2-3............... 05/29/92.... PTO Driveline QD Slide Collar Update.972205 (970006A)........ 2-4............... 05/22/97.... Blade Recall, (Gorilla Tree Cutter)971612 (970011A)........ 2-5............... 12/16/97.... Slip Clutch Spring Update Kits981704 (980001A)........ 2-6............... 03/17/98.... Blade Date Code Inspection / Recall.000808 (200002)...........2-7............... 08/08/00.... Gearbox Height Spacer Kit (AG72)001108 (200003)...........2-8............... 08/08/00.... Gearbox Height Spacer Kit (AG60)002112 (122100A)........ 2-10............. 12/21/00.... Blade Date Code Inspection / Recall.011704 (041701B)........ 2-12............. 04/17/01.... Blade Date Code Inspection / Recall (2 nd notice).


NOTES

© 2004 Alamo Group Inc. 1-1

MECHANICAL ROTARY

SECTION 1

TECHNICALINFORMATION

BULLETINS

(This Book is divided into two Sections)

Section One - Technical Information Bulletins

1. Technical Information Bulletins: Information Bulletins are listed by Bulletin Number (Date).Example the oldest Bulletin will be listed first and the most recent bulletin will be listed last.Bulletin No. 021002 = first & second digits are the month, the third & fourth digits are the dayof the month and the fifth & sixth digits are the year this means, the bulletin was written on Feb,10, 2002. If more than one bulletin was written on that day the a dash with a number will added,example -1, -2 etc.

2. Authorize Repairs: Technical Information Bulletins do not authorize any repairs to be madeunder warranty or any other circumstance unless specifically instructed to do so.

3. Bulletin Reference: Some Technical Information Bulletins will refer to the correspondingService Bulletins for repairs and some are for information only.

4. Bulletin Instructions: Technical Information Bulletins should have all the instructions as towhat you need, but may not have all the information needed to make an installation complete.In some cases it may be required to refer to other manuals for more complete information, thisshould be suggested in the Technical Information Bulletin.

5. All Technical Information Bulletins printed in this Manual will void any previously printed Bulletins Any changes in these bulletins are the final version as of the date of this manual.


MECHANICAL ROTARY

TECHNICAL INFORMATION BULLETIN No. 040896Alamo Industrial ™ Technical Services Department

1502 East WalnutSeguin, Texas 78155

830-372-2708

Models: All Models using Single Acting Hydraulic Cylinder Date:

Apr. 8, 1996

Bulletin No:

040896

This document does not authorize the repair or replacement of parts under warranty

Oil Leaking from new single Acting Hydraulic Cylinders:

There have been numerous cases of the dealers and customers replacing single actinghydraulic cylinders on new machines due to oil leakage out of the vent plug in the cylinder.

In many of these instances, no defect could be found in the cylinders. Further investigationhas revealed that he manufacture of our cylinders is leaving oil in the cylinders after their testing. TheOil is left to help protect the interior of the cylinders during storage. When the cylinders are fullyactuated, they are forcing this oil out the vent plug, causing what appears to be a leaking cylinderthrough the vent plug. Even the oil is cleaned off the cylinder after testing there is enough oil still insidethe cylinder to bleed out when used.

If you have a New Cylinder that appears to be leaking from the vent plug, The oil should becleaned off and unit ran for a few days to a week to determine if the Cylinder is leaking, or if it is theoil that was left in the cylinder to protect it. It has been found that in some cases it has taken as muchas a week for this to appear that it is not leaking.

If after running and cycling the cylinder during operation and the cylinder continues to leak thenthe necessary repair should be performed.

Cylinders that are attracting dust around them is not considered to be leaking. This dustcollecting around them is considered normal.

All Cylinder that are returned as leaking will be pressure tested for leakage to determine thecondition of the Cylinder and its components.


MECHANICAL ROTARY



830-372-2708

Models: All Models 2 or 4 Disk Springless Design Slip Clutch Date:May 6, 1997

Bulletin No:050697(old # 050697A& # 043097R)


Springless Slip Clutch Adjustment Procedure:In order to avoid damage to the mower or clutch assembly, it is important that the clutches

slip when an obstacle which creates a load that is heavier than the clutch setting is encountered. Inorder to ensure that the clutches are properly set the following adjustment procedure must befollowed. Make note, step 3 must match the type clutch, 2 disk or 4 disk type.1. Loosen all of the 8 clutch adjusting bolts until they are loosely in the clutch. While you are doingthis it is a good time to inspect the clutch to make sure all the friction disk are in good condition andare not stuck to the pressure / drive plates. See the operators / parts manual for more detail.2. Gradually and evenly tighten the bolts to the correct initial setting. To achieve the properinitial setting. Gradually tighten all of the bolts in an alternating pattern (See Figure 2) until the bolthead and nut comes in contact with the clutch outer plate. Continuing tightening the nuts only untilthe point at which the bolt and nut can be rotated in the housing using 5 to 10 inch lbs. of force. Severalcycles of tightening may be necessary until this hand tight point is reached.3A. 2 Disk Clutch: If your unit uses a 2 disk clutch, use the proper size wrench to gradually tightenthe bolts in sequence (See Figure 2) from 7/8 to 1 full additional turns more to achieve the final setting3B. 4 Disk Clutch: If your unit uses a 4 disk clutch, use the proper size wrench to gradually tightenthe bolts in sequence (See Figure 2) from 1-1/8 to 1-1/4 full additional turns more to achieve the finalsetting

1

2

3

4

56

7

8

Figure 1 Figure 2


MECHANICAL ROTARY



830-372-2708

Models: All Models Using a Slip Clutch on Driveline Date:Oct. 23, 1998

Bulletin No:102398


Clutch Disk Linings, Using Will Fit Substitute :Evidence recently revealed indicates a general attitude of many dealers to provide "will fit" or

non OEM clutch disk linings as replacement parts for the Alamo Industrial standard disk lining.

Many of these substitute disk are constructed of a material which exhibits a low pH and are,therefore, acidic in nature and tend to attract moisture. These characteristics result in a mild acidicreaction or electrolysis and corrosion of the metal components. Testing has reveled that thiscorrosion will result in adhesion of the disk lining to the metal plates in as little as two weeks time. Infact , in some cases, it was required to chisel the lining from the metal plate with a hammer and chisel.

Typical modes of failure which result from this adhesion of the lining involve many mechanicalcomponent failures to mower as well as tractor.

Clutch lining exhibiting this characteristic can be identified as being dark grey or black in color,and are available from many "will fit" suppliers. The current Alamo Industrial clutch Disk lining materialis formulated with a pH of 12 which indicates a very basic or alkaline material. In addition, the materialis impregnated with brass to provide a smooth slipping characteristic and lubrication during clutchactivation. Zinc is also impregnated into the material to provide for corrosion resistance due toelectrolysis. These standard disk are identified

Figure 1

as being tan or light brown in color, and appearto be more dense in structure than the "will Fit"disks.

Warranty claims for components fail-ures when these "will fit" disk linings are used tosubstitute for Alamo Industrial replacement partswill be subject to denial pending investigationinto the use of these. If it is determine these "willfit" disk are being used all warranty on failure ofany of the drive components, Drivelines, Gear-boxes, Blade Carriers, Clutch, Clutch Compo-nents or the Tractor itself will be denied.

Friction Disk Lining


MECHANICAL ROTARY



830-372-2708

Models: All Three Point Lift Type Models Date:Nov. 24, 1998

Bulletin No: 112498


Three Point Lift Category Dimensions:

There have been numerous inquiries as to the sizes and dimensions relating to the categoryof the three point hitch. The purpose of this bulletin is to offer a quick reference.

File this information in your sales manual for reference. This information concerns the sizesof the hitches available on tractors. The term used to identify the size is "category". The categoriesare linked to the tractor horse power. The Horse power divisions overlap and some tractors are intwo categories. Cat "0" is for garden tractors, less than 20 HP. Cat "I" is for 20 to 45 HP. Cat "II" isfor 40 to 100 HP. Cat "III" is 80 to 225 HP and Cat "IV" is from 180 to 400 HP.

Cat. A-Frame Upper Pin DiaHitch Width Height Top & Btm

("A") ("B") ("C" & "D")"0" 20" 12" 5/8" & 21/32""I" 27" 18" 3/4" & 7/8""II" 32" 19" 1" & 1-1/8""III"-N 32" 22" 1-1/4" & 1-7/16""III" 38" 22" 1-1/4" & 1-7/16""IV" 46" 27" 1-3/4" & 2"

Note: There are units that will be installed withdifferent size hitch pin (item "D") than the with.This is usually done as an example, Cat I Hitchwith Cat II Pins. There is also Cat III Narrow,this is special Cat II Width with Cat 3 height.All tractors can not be made to fit a smallerCat Hitch, it depends on tractor manufactureras to whether it was designed to.

"A"

"B"

"C"

"D"Figure 1


MECHANICAL ROTARY

NOTES

© 2004 Alamo Group Inc. 2-1MECHANICAL ROTARY

SECTION 2

SERVICEBULLETINS

(This Book is divided into two Sections)Section Two - Service Bulletins

1. Service Bulletin No: Service Bulletins are listed by Bulletin Number (Date). Example theoldest Bulletin will be listed first and the most recent bulletin will be listed last. Bulletin No. 021004= first & second digits are the Year, the third & fourth digits are the day of the month and the fifth& sixth digits are the month, this means the bulletin was written on Apr, 10, 2002. If more thanone bulletin was written on that day the a dash with a number will added, example -1, -2 etc.

2. Repairs: Service Bulletins are intended to authorize only the repairs listed on It to be madeunder warranty or any other circumstance unless specifically instructed to do so.

3. Parts: This is the Rate at which compensation will be allowed under warranty for repair parts.4. Labor: This is the amount of labor (hours) that are allowed to make this repair under warranty.5. Parts Disposition: Service Bulletins list the disposition of any parts that are removed during the

repair. If listed removed parts must be held awaiting return to factory if instructed to do so.6. Termination Date: Service bulletins show a termination date, this is the date that the Bulletin

will be discontinued, Any repairs must be made and all warranty applications filed by the listeddate.

7. All Service Bulletins printed in this Manual will void any previously printed Bulletin. Anychanges in these bulletins are the final version as of the date of this manual.


MECHANICAL ROTARY

SERVICE BULLETIN No. 922002Alamo Industrial Technical Services Department


830-372-2708

Aircraft Tire & Wheel Operating Procedure :

Subject:The Aircraft Tire & Wheel needs to be operated in a safe manner, the purpose of this bulletin is

to instruct on the proper and safe operation of this wheel

Service Required:Wheel inspection, operation procedures and operating limitations.

1. Maximum inflation pressure 50 psi.2. Maximum Transport Speed 20 MPH3. DO NOT mount any other type tire on

wheel supplied with the aircraft tire.4. Remove all air pressure from tire prior

to trying to dismount tire.5. Alamo replacement tube the aircraft tire

and wheel (P/N 00749700 Tire & Wheel)is Tube P/N 00720302, This is a specialtube for the aircraft tire and is not generallyavailable at most tire stores.

Parts Involved:P/N 00749700 = Aircraft Tire & Wheel

Assembly (25.5 X 8 X 1420-Ply Aircraft Tire & Wheel).

P/N 00720302 = Replacement Tube forAircraft Tire & Wheel above.

Models: All Models using Aircraft Tire & Wheel P/N 00749700 Date:

Feb. 20, 1992

Bulletin No: 922002(Old # 92-002)

Parts:100 % at Dealer Net

Labor:.0 hr. (to be determine oncase by case)

Termination Date:May 15, 1992

Old Parts Disposition:No Parts Involved

Warranty Compensation will be provided following proper filing of warranty claim in accordance withthe Alamo Industrial Warranty Policy. Claim allowance may vary in accordance with laws governing aspecific region. Any Warranty associated with this service bulletin must be within authorized dates.

Figure 1

DO NOT REMOVE theseassembly bolts beforeall air pressure hasbeen releasedfrom tire




830-372-2708

Slide Yoke QD Collar Modification :

Subject:1-3/8" X 6 Spline & 1-3/8" X 21 Spline PTO Yokes which connect to the tractor. The Metal ring of

the design shown (see figure 1) must be replaced. If not replaced it could disconnect from the tractor PTOshaft.

Service Required:Remove the retaining ring (1), then remove the collar (2) and the metal ring (3). Inspect the metal

ring to determine what type is present, replace metal ring as required. Reinstall collar (2) and retaining ring(1). Make certain the locking balls are in place.

Parts Involved: (item 4 in Figure 1)Parts were sent to customers.

Models: AG15-IV, A415, AG84B (Pull Type), A310, AG20, AG10 Date:

May 29, 1992

Bulletin No: 922905(Old # 92-008)


Labor:0.25 hr. At DealerRegistered Labor Rate

Termination Date:July 31, 1992

Old Parts Disposition:Discard old parts


1/2" RadiusMetal Ring Designwhich must bereplaced

New Metal Ring replacementdesign with chamfer

1/8"

3/16"1 2 34

5 Item Description1 Retaining Ring2. Outer Collar3 Locking Balls4. Metal Lock Ring5. Spring

Figure 1


MECHANICAL ROTARY



830-372-2708

Blade Recall, Gorilla Tree Cutter : (Blade P/N 00770975)

Subject:Tree Cutter Blade P/N 00770975 recall due to the possibility of the use of subtandard material.

Service Required:Remove and replace all of the blades with new blades. NOTE: Apply thread locking compound

to the blade bolt threads and torque the blade bolt nuts to 2000 ft. lbs. See Operators manual for moredetail.Parts Required:Part No. Qty Description00770971 2 Blade Set (matched set of two)

Models: All Gorilla Tree Cutter Rotary Mowers Date:

May 22, 1997

Bulletin No: 972205(Old # 970006A)


Labor:1.5 hr. At Dealer RegisteredLabor Rate

Termination Date:Jul. 15, 1997

Old Parts Disposition:Retain Parts for Return


Figure 1




830-372-2708

Clutch Coil Spring Kits :

Subject:During September of 1996, utilization of a "springless" design 2 and 4 disk slip clutch (figure 1)

was implemented for use in several mower models. This design was used to replace the original externalcoil spring design (Figure 2), and provided equal levels of durability and safety along with a cleanerappearance. However, the difficulty involved in adjusting this clutch, along with its lack of acceptance bycustomers, has necessitated the discontinuation of the new clutch, and a return to the old design.

Service Required:Convert the new internal spring (Springless) design clutch to the old coils spring design using

the conversion kits listed. 2 disk clutch use kit P/N 00773222 & 4 disk clutch use kit P/N 00773224.The Spring Kits will include pressure plate, Bolts, Nuts and Springs (Kit will not included clutch lining)1. Remove the clutch from the gearbox. Disassemble the clutch assembly and remove thepressure plate along with the nuts and bolts.2. Reassemble the clutch using the diagram and parts breakdown located in the parts section ofthe Operators manual. Install all the parts, pressure plate, springs, bolts and nuts.3. Adjust the clutch in accordance with the instructions provided in the Operators manual.

Models: All AG Mechanical mowers using either the 2 or 4 diskinternal spring design (Springless) slip clutchClutch P/N 00756075A (4 disk) or 00754320A (2 disk)

Date:

Dec. 16, 1997




Termination Date:Feb 28, 1998

Old Parts Disposition:Retain Parts for return


Figure 1 Figure 2

Internal Spring(Springless)Clutch

External Spring(Coil Spring)Clutch


MECHANICAL ROTARY



830-372-2708

Blade Date Code Inspection : (with listed date code only apply)Subject:

Normal random inspection of blades manufactured during the time period from Jan. 7, 1998 to Mar.11, 1998, which are utilized on the above listed machines indicates that the quality of a small percentageof the blades, may be lower than that which is acceptable to Alamo Industrial standards.Service Required:

As a precaution, and in the interest of promoting complete customer satisfaction, the followingrepair procedure is deemed necessary:1. Replace the mower blades on each mower or mower section as listed above. Only change theblades (blade P/N listed below) on models listed above and blade with the dates codes listed below.2. Inspect any blades located in your parts stock with the following date codes that are spare partsfor the above listed models and/or sections.3. Date Codes of affected blades are 08007 to 08063, the date codes are stamped into the undersideof the blade next to the blade bolt hole, they can be seen from the underside.Parts Involved: Mower blades involved are P/N 00750788T, 00759339, 0622010330, 582013, 8588AHA750788T & HA582013 but only blades with the above date codes.

Models: Hydro 15 Wing Only s/n 02067 to 02110Hydro 10 Wing Only s/n 02098 to 02111, AG72 s/n 01759 to 02030,AG72H s/n 01013, AG15-IV wing only s/n 03946 to 03970, AG60Bs/n 01472 to 01589, AG72B s/n 02113 to 02160 & 01663 to 01670

Date:

Mar. 17, 1998



Labor:.0 hr. (to be determine oncase by case)

Termination Date:May 15, 1995

Old Parts Disposition:Retain Parts involved forreturn


Figure 1

Mfg. Date Code

Undersideof Blade

Blade Bolt Hole

Blade P/NAlamoLogo

Torque Blade Bolt toSpecfications listed in operatorsmanual for the model beingrepaired




830-372-2708

Gearbox Height Spacer Kit P/N 00776041 : (includes parts listed below)Subject:

Insufficient clearance between the cutting blade height and skid shoe may cause excessivecontact with the ground and excessive wear to the cutting componentsService Required:

Turn "off" and secure mower and tractor. (follow all safety procedures in operators manual)1. Remove the mower from the tractor as detailed in the operators manual.2. Remove the six bolts that retain the gearbox to the deck, you will not have to remove blade carrier

or driveline from gearbox.3. Using a suitable hoist, lift the gearbox (with Blade carrier still attached) up so that a gap is created

between gearbox flange and deck, this allows you to install the 2 spacers P/N 00776040 betweengearbox flange and mower deck.

4. Install the 6 new 5/8" bolts through thedeck, spacer and gearbox flange, install the 6 new locknuts and torque them to170 ft. lbs.

5. Reinstall all safety shields or anyother component you had to remove

6. Attach mower to tractor as shown in operators manual, run and test mower.

Parts Involved: (Kit includes these)Part No. Qty Description00776040 2 Gearbox Spacer Half00750311 6 Bolt, 5/8"00695100 6 Lock Nut, 5/8"

Note: Longer bolts must be installed wheninstalling specer kit, new bolts are 1/2" longerthan the old ones.

Models: AG72 Model Rotary S/N 01028 to 01030 & S/N 02370 toS/N 02538

Date:

Aug. 8, 2000

Bulletin No: 000808(Old # 200002)



Termination Date:Oct, 15, 2000

Old Parts Disposition:No Parts Involved to return


Figure 1

Spacers

Mower Deck

Gearbox

Blade Carrier


MECHANICAL ROTARY



830-372-2708

Gearbox Height Spacer Kit P/N 00776077 : (includes parts listed below)Subject:

Insufficient clearance between the cutting blade height and skid shoe may cause excessivecontact with the ground and excessive wear to the cutting componentsService Required:

Turn "off" and secure mower and tractor. (follow all safety procedures in operators manual)1. Remove the mower from the tractor as detailed in the operators manual.2. Remove the six bolts that retain the gearbox to the deck, you will not have to remove blade carrier

or driveline from gearbox.3. Using a suitable hoist, lift the gearbox (with Blade carrier still attached) up so that a gap is created

between gearbox flange and deck, this allows you to install the 2 spacers P/N 00776040 betweengearbox flange and mower deck.

4. Install the 6 new 5/8" bolts through thedeck, spacer and gearbox flange, install the 6 new locknuts and torque them to170 ft. lbs.

5. Reinstall all safety shields or anyother component you had to remove

6. Attach mower to tractor as shown in operators manual, run and test mower.

Parts Involved: (Kit includes these)Part No. Qty Description00776040 2 Gearbox Spacer Half00750311 6 Bolt, 5/8"00695100 6 Lock Nut, 5/8"

Note: Longer bolts must be installed wheninstalling specer kit, new bolts are 1/2" longerthan the old ones.

Models: AG60 Model Rotary S/N 01610 to 01656 & S/N 01706 toS/N 01506

Date:

Aug. 11, 2000

Bulletin No: 001108(Old # 200003)


Labor:2.0 hr. At Dealer RegisteredRate

Termination Date:Oct, 15, 2000

Old Parts Disposition:No Parts Involved to return


Figure 1

Spacers

Mower Deck

Gearbox

Blade Carrier


NOTES


MECHANICAL ROTARY



830-372-2708

Blade Replacement Notice, Rotary Mowers:Subject:

During random inspection of rotary mower blades, we determined that a small quantity of bladesmay be of a quality lower than that which is acceptable to Alamo Industrial. These blades can beidentified by the Alamo Industrial Logo, Part Number and Date code that is stamped on the blade nextto the blade bolt hole (See Figure 1). Refer to the Blade Numbers listed in this bulletin and theircorresponding date codes to identify the blades to be replaced.Service Required:

To prevent possible blade failures, the following repair procedure is deemed necessary.Immediately inspect all Alamo Industrial Rotary Mowers to determine if they are fitted with bladesidentified in this bulletin. Replace all blades that have matching part numbers and date codes listed onthe following pages. Inspect all of your Parts Inventory of blades to determine if any of these blades onhand match the part numbers and date code. Only blade with matching part number AND date codeswill apply to this bulletin. Blade can be check without removing them as the part number and date codesare on the underside of the blade.Parts Required:

Rotary Mower Blades on mowers and / or in parts inventory should be replaced if numbers anddate codes match those listed.

Models: Any Rotary Mower using any of the blade Part Numberswith the indicated date codes listed in this bulletin.

Date:

Dec. 21, 2000



Labor:Refer to Alamo Flat ratemanual for labor time

Termination Date:Apr. 30, 2001

Old Parts Disposition:Retain Removed Parts forRecall

Continued Next Page

Figure 1

Mfg. Date Code

Undersideof Blade

Blade Bolt Hole

Blade P/NAlamoLogo




Service Bulletin 002112 Continued from previous Page

SERVICE BULLETINNo. 002112

NOTICE:The following list of Blades and date codes are the only blades that this bulletin applies to. The

part number with the corresponding date code must be stamped on the same blade. Do Not changea blade based on part number or date code alone.

Blade Part No. Date Code

00127028....................................................... 0158 or 0159 or H1094

00750787T..................................................... 0080 or 0081

00750788T..................................................... 0073 or 0075

00752974....................................................... 0295

00753254....................................................... 0110 or A09619

00753841....................................................... 0166 or 0167 or 0306

00753842....................................................... 0165 or 0166

00762435....................................................... 0167

00770975....................................................... 8306 or 9321

02726900....................................................... 0089 or 0129 or 0131 or 0130 (*)

02886200....................................................... 0215

02962635....................................................... 0201

02964824....................................................... 0027

0582010330................................................... 0180 or 0285 or 0287

1255A............................................................. A000550

582013........................................................... A000660

7520............................................................... 0230

8588............................................................... 0010 or 0095 or 0096 or 0138 or 0251

or 7246 or 9134 or 9258

8589............................................................... 0146 or 0153 or 0158 or 0244 or 0251

8590............................................................... 0143 or 0144 or 0234

(*) Heat Code


MECHANICAL ROTARY



830-372-2708

Blade Replacement Notice, Rotary Mowers: - SECOND NOTICE -Subject:

During random inspection of rotary mower blades, we determined that a small quantity of bladesmay be of a quality lower than that which is acceptable to Alamo Industrial. These blades can beidentified by the Alamo Industrial Logo, Part Number and Date code that is stamped on the blade nextto the blade bolt hole (See Figure 1). Refer to the Blade Numbers listed in this bulletin and theircorresponding date codes to identify the blades to be replaced.Service Required:

To prevent possible blade failures, the following repair procedure is deemed necessary.Immediately inspect all Alamo Industrial Rotary Mowers to determine if they are fitted with bladesidentified in this bulletin. Replace all blades that have matching part numbers and date codes listed onthe following pages. Inspect all of your Parts Inventory of blades to determine if any of these blades onhand match the part numbers and date code. Only blade with matching part number AND date codeswill apply to this bulletin. Blade can be check without removing them as the part number and date codesare on the underside of the blade.Parts Required:

Rotary Mower Blades on mowers and / or in parts inventory should be replaced if numbers anddate codes match those listed.

Models: Any Rotary Mower using any of the blade Part Numberswith the indicated date codes listed in this bulletin.

- SECOND NOTICE -

Date:

Apr. 17, 2001

Bulletin No: 011704(Old # 041701B)


Labor:Refer to Alamo Flat ratemanual for labor time

Termination Date:May. 30, 2001

Old Parts Disposition:Retain Removed Parts forRecall

Continued Next Page

Figure 1

Mfg. Date Code

Undersideof Blade

Blade Bolt Hole

Blade P/NAlamoLogo




Service Bulletin 011704 Continued from previous Page

SERVICE BULLETINNo. 011704

NOTICE:The following list of Blades and date codes are the only blades that this bulletin applies to. The

part number with the corresponding date code must be stamped on the same blade. Do Not changea blade based on part number or date code alone.

Blade Part No. Date Code

00127028....................................................... 0158 or 0159 or H1094

00750787T..................................................... 0080 or 0081

00750788T..................................................... 0073 or 0075

00752974....................................................... 0295

00753254....................................................... 0110 or A09619

00753841....................................................... 0166 or 0167 or 0306

00753842....................................................... 0165 or 0166

00762435....................................................... 0167

00770975....................................................... 8306 or 9321

02726900....................................................... 0089 or 0129 or 0131 or 0130 (*)

02886200....................................................... 0215

02962635....................................................... 0201

02964824....................................................... 0027

0582010330................................................... 0180 or 0285 or 0287

1255A............................................................. A000550

582013........................................................... A000660

7520............................................................... 0230

8588............................................................... 0010 or 0095 or 0096 or 0138 or 0251

or 7246 or 9134 or 9258

8589............................................................... 0146 or 0153 or 0158 or 0244 or 0251

8590............................................................... 0143 or 0144 or 0234

(*) Heat Code


MECHANICAL ROTARY

NOTES


Mechanical Rotary Models Technical Information Bulletin

andService Bulletin

Manual

Manual P/N 02980508(01/04)

Documents

01, Front Cover - Alamo Industrial · 2008-09-17 · Alamo Industrial ™ Technical Services Department 1502 East Walnut Seguin, Texas 78155 830-372-2708 Models: All Models using