08/2015 - Martin Robey · PDF file · 2015-10-0908/2015 Martin Robey Engineering ... Series 1 and Series 2-3 E-type models , ... 2 X MRE10LH/RH SIDE FRAME LOWER MTG BRACKETS £38.70

08/2015

08/2015

Martin Robey Engineering Limited have been producing completely new Body Shells for E Type Jaguars since 1982, after restoring several Body Shells it was apparent that they all suffered similar corrosion problems and when corrosion damaged panels were removed it only revealed further corrosion and undesirable repairs, there never seemed much of the original body left before the rebuild could take effect, therefore it was decided to produce the few remaining panels that were not in production at the time and start producing all New Body Shells.

To accommodate customers with some of their own parts such as Doors, Boot Lids and Bonnets the “System One, Two and Three” processes came about.

“Floor Units” & “Sub-Assemblies” are also available for the experienced who wish to rebuild their Body Shell or complete a “Sub Assembly” using “Our Panel Kits”.The Body Shells use high quality Martin Robey Body Panels

that are Pressed Out, LaserProfiled and assembled using Motor Industry Methods and equipment, quality appearance and dimensional accuracy to the original specification is an important feature of the Martin Robey Panels and Body Shells.

The build process involves using sub units such as Bulkheads, Floors, Rear End Assemblies etc., which are all assembled

on several major assembly jigs which locate key mounting points throughout the build process professional Spot Welders are used to give an original appearance and adhere to the original design.

Ser.1-2 and 3 Models are available in both Drop Head and Fixed head versions.the completed Bodies are Lead Loaded Cleaned off, the door seals are fitted to give a better than original fit to Door, Bonnet gaps etc.External Chrome work is trial fitted prior to leaving the works where the Body Shells can be ready for the Paint Process.

Martin Robey Engineering Ltd. recently installed its very first Robot. The Robot is the latest of many of the company’s machines that are fully computerised.

A completed Ser 1 E-Type body shell built to system 3 specifications ready for the paint process

E-type Floor Units are assembled in a series of comprehensive assembly jigs

08/2015

Full Body Shells are available in several variation we call them “System Rebuilds”.

“System I” is a complete Body Shell, all new with a Bulkhead fitted and all welded with your Doors and Bootlid Fitted, Lead Loaded and cleaned back, all fully jig Built.

Series 1 3.8 DHC models £26,794.43* Series 1 4.2 DHC models £26,834.50* Series 2 4.2 DHC models £26,840.24*

“System II” is a System I with a Doors and Boot Lid Supplied and Fitted Series 1 3.8 DHC models £28,703.04* Series 1 4.2 DHC models £28,743.26* Series 2 4.2 DHC models £28,229.77*

“System III” is a System II with a Bonnet supplied and fitted with front-rear lights, Bumpers, Door chromes and trial fitting.

Series 1 3.8 DHC models £36,398.36* Series 1 4.2 DHC models £36,438.54* Series 2 4.2 DHC models £36,418.58*

Fixed Head ModelsPrices shown are for Ser.1-2 Drop Head Coupe Models. For Fixed Head Coupes please add £9,500 based upon customer supplying roof assembly and rear hatch unit in suitable con-dition.

All Prices are EX-Works and subject to VAT if applicable *Aug 2015 - Jul 2016

System Re-Builds are available normally in approximately 18-26 weeks from order and deposit.

The prices given do not include any Fixtures, Fittings, Hinges, Locks, Engine Frames etc, or Packing or Shipping.

Additional Equipment: Inner Sill Reinforcing £150.00, Inner Seat Belt Kit £100.00, Early 3.8 Features Can Be Incorporated Into Systems and Sub Assembly units.

A Ser.1 3.8 DHC restored at the works using a complete Martin Robey Body Shell to System 3 Specifications.

Full Body Shells System Re-Builds

08/2015Ser.1 3.8 Early FeaturesVery Early E Types have early features that were discontinued as part of upgrades for these early cars.

Careful research and study of the Motor car is essential to evaluate which of these features are relevant to particular vehicles and there probably was not two vehicles exactly the same in the first few days-weeks of production. It must be remembered that some vehicles will have undergone factory upgrades or as part of general servicing or restoration during the life of the vehicle.

It must be also remembered that many more vehicles were exported to the USA that upgrades may have been incorporated to Federal Specification Cars that UK Cars built in the same period so dates of manufacture is not the only consideration to be made, Chassis or VIN Number is the most important Allie in identifying early features, there are several books available that list most, but not every feature by relevance to chassis Number.

We offer most of the important Early Features for the Ser.1 3.8 models, we offer them as a Fixed Price Supplement and can usually accommodate other less well known features that may have been fitted to a very smaller number of vehicles or perhaps just the one.

Early Features 3.8 Ser.1Bonnet (Front End) Separate Louvre Panels

Spot Weld Air Valence PanelsSeam Welded Centre Panel Nose SectionSide Locking Mechanism

Bulkhead Unit Bolt On Mirror Rod Bracket FixingsPop Riveted Brake-Clutch Reservoir BracketSide Locking ‘A’ Post Without Pressing For Lock RodTransmission Tunnel Side Panel RH Plain Pressing

Inner Sill Weld Nuts For Side Locking Bonnet CatchesFloor Panels Flat Floors Without Footwell Including Separate (2 Part) Radius Cup Mounting

PlateRear Bulkhead PanelStraight One Piece Without Separate Weld For Extra Seat Movement

Door Assembly Early Style Door Inner Panel, FHC & DHCEarly Style Drip Tray, FHC & DHCDoor Skin 2 Part With Spot Welded Top Section For Slim Early Top Door Chromes Finisher (DHC Only)

Boot Floor & Rear End Assembly

Pop Riveted Reversing Light Pod With Boot Floor Rails One Piece Spot Welded

Pop Riveted Reversing Light Pod With Boot Floor Stiffeners 3 Part Style With Centre One Pop Riveted In PositionPop Riveted Reversing Light Pod With All Rails 3 Part Style All Pop Riveted In PositionWater Drain Tubes1 Central One Fitted On LH Side Of Reversing Light Pod1 Central Plus 1 Further On RH Rear Quarter Panel

Number Plate Panel Small Aperture For Rear Light AccessFuel Filler Box Fuel Filler Box without Reinforcing Indentation top Half Of filler Box And

Without Drawn Tube To Fuel BoxPlease Note:There are other early features to the Body Shell UnitsPlease do not hesitate to talk to us about your Motor Car; we can usually accomodate these even if not listed

08/2015

A “Sub Assembly Unit” is a Body Shell with a New Bulkhead supplied and fitted but without the outer body panels supplied and fitted. “Ser 1 3.8 Sub Assembly Unit” with Bulkhead £ 14,192.25* “Ser 1 4.2 Sub Assembly Unit” with Bulkhead £ 14,232.25* “Ser 2 4.2 Sub Assembly Unit” with Bulkhead £ 14,291.59*The Sub Assembly is designed for the experienced amateur Body Builder or the Professional Body Shop. These Units are mostly welded together and can be completed without the use of a Full Assembly Jig.

Sub Assembly without Bulkhead and without the Outer Body Panels Fitted.

“Ser 1 3.8 DHC Sub Assembly Unit” without Bulkhead £9,488.98* “Ser 1 4.2 DHC Sub Assembly Unit” without Bulkhead £9,529.04* “Ser 2 4.2 DHC Sub Assembly Unit” without Bulkhead £9,584.32*Delivery is usually approximately 6-10 weeks from Order.

The cost of a new bulkhead not fitted is £4,703.27*

The outer Body Panels that are not fitted are available in Kits.

Being:

Ser 1 DHC 3.8 & 4.2 “Alpha” Base Kit (See list of Parts) £2,187.57*

Ser 1 DHC 3.8 & 4.2 “Beta” Alpha Kit plus Door and Bootlid £4,090.08*

Ser 1 DHC 3.8 & 4.2 “Delta” which is a Beta plus a Bonnet £9,514.40*

All prices are ex works and subject to Value Added Tax for European Sales.

* Aug 2015 - July 2016

ADDITIONAL EQUIPMENTInner Sill Reinforcing £150.00

Inner Seat Belt Kit £100.00Early 3.8 Features Can Be Incorporated Into

Sub Assembly Also

Sub Assembly Units Roadster Series 1-2

08/2015

Sub Assembly Units For Fixed Head Coupé

We can build Sub assembly’ units for FHC, Series 1 and Series 2-3 E-type models, we can vary the content of the unit to suit to vehicle requirements. Therefore any prices shown are to guide only.

Guide price with new bulkhead supplied and fitted £13,701.15 + VAT

They are designed for fitting the roof assembly and outer panels by a professional restorer or experienced enthu-siast. They can be supplied with a either a new bulkhead supplied and fitted, using a reconditioned bulkhead or using a suitable bulkhead supplied by a customer.

*Aug 2015 - July 2016

08/2015

Floor Units

Full floor unit For Series 1 3.8 flat floor model

3.8 Footwell floor assembly

Available for series 1&2 Drop Head and Fixed Head models

£1,313.57*(Ex.VAT)

£3,025.12*(Ex.VAT)

Call for more information!+44 (024) 76386903

All Prices are subject to VAT if applicable *Aug 2015 - July 2016

08/2015

SUB ASSEMBLY UNIT FOR SER.1 3.8ROADSTER WITH REAR END ASSEMBLY

Pool Road,Camphill Industrial Estate,Nuneaton, WarwickshireCV10 9AE EnglandTELEPHONE No. +44 (024) 76 386903FAX No. +44 (024) 76 345302E-MAIL [email protected] www.martinrobey.comCOMPANY REG No. 1980684VAT REG No. GB 487 666 775

ALL PRICES SUBJECT TO VAT AS APPLICABLE AND IN GBP The above are mostly welded in place except for some items that may require slight adjustment before welding.This Assembly is Jig Built and can be supplied with a Kit of Outer Body Panels that are not Fitted to the above Sub Assembly. SUB ASSEMBLY WITHOUT BULKHEAD £9,488.98SUB ASSEMBLY WITH BULKHEAD £14,192.25 3.8 shown for illustration only.

Unit FittedWith Inner Sill Reinforcings

Qty Part Number Description Individual Price Combined Price

1 X BULKHEAD BULKHEAD UNIT INCLUDING TOP SKUTTLE PANEL £4,703.27 £4,703.27 2 X BD16008F/R FUEL TANK MTG BRACKET £16.15 £32.30 1 X BD16212 REINFORCING TONNEAU £59.78 £59.78 2 X BD18949/50 BOOT HINGE MTG BRACKET £13.06 £26.12 1 X BD18963 INTERIOR LIGHT SHIELD £29.34 £29.34 1 X BD27181 FUEL PUMP MTG BRACKET £19.11 £19.11 2 X MRE10LH/RH SIDE FRAME LOWER MTG BRACKETS £38.70 £77.40 2 X MRE112ALH/BRH TRANSMISSION TUNNEL SIDE PANELS £62.81 £125.62 1 X MRE115 TUNNEL STIFFENER £47.92 £47.92 2 X MRE117LH/RH STIFFENERS £40.99 £81.98 2 X MRE118LH/RH CLOSING PANEL £22.41 £44.82 1 X MRE119 CENTRAL TUNNEL FACING £68.59 £68.59 2 X MRE120LH/RH TUNNEL FWD SIDE £103.66 £207.32 2 X MRE121LH/RH INNER PEDAL SIDE £13.23 £26.46 1 X MRE122RH OUTER PEDAL £13.06 £13.06 1 X MRE122ELH OUTER PEDAL SIDE 3.8 £21.67 £21.67 2 X MRE14LH/RH FULL FLOOR £210.42 £420.84 2 X MRE15LH/RH INNER SILLS £81.10 £162.20 2 X MRE19 FRONT STIFFENERS £17.81 £35.62 2 X MRE20RH/LH REAR STIFFENERS £17.81 £35.62 1 X MRE24A CROSSMEMBER TO FULL FLOOR £68.01 £68.01 2 X MRE29RH/RH INN ARCH LH £255.93 £511.86 2 X MRE2LH/RH BHD TO SILL £21.29 £42.58 2 X MRE30RH/LH DOOR SHUT FACE PANEL ASSY £41.75 £83.50 1 X MRE3ARH RH 3.8 BULKHEAD PANEL £37.58 £37.58 1 X MRE4ALH LH 3.8 BULKHEAD PANEL £37.58 £37.58 1 X MRE42A CLOSING PANEL £44.18 £44.18 1 X MRE58 UPPER FLOOR £293.96 £293.96 2 X MRE59LH/RH FLOOR STIFFENER BRACKETS £23.61 £47.22 1 X MRE60 TUNNEL ASSEMBLY £224.51 £224.51 1 X MRE61 TOP PANEL REAR FLOOR £77.26 £77.26 1 X MRE62 PANEL FRONT TO BOOT FLOOR £59.50 £59.50 1 X MRE63 PANEL ASSEMBLY £85.52 £85.52 1 X MRE64 REAR BULKHEAD £170.06 £170.06 1 X MRE65 REINF CHANNEL £146.54 £146.54 1 X MRE68BRH RH 38 ARCH VALANCE £140.83 £140.83 1 X MRE68LH INN VALANCE LH £140.83 £140.83 2 X MRE69LH/RH ARCH FWD £135.53 £271.06 2 X MRE71LH/RH TOP PANEL INNER £77.61 £155.22 2 X MRE72LH/RH REAR CHASSIS LEGS £230.36 £460.72 2 X MRE73A RADIUS ARM CUPS (RIVETED) £50.01 £100.02 2 X MRE76LH/RH INNER PANEL DOOR SHUT FACE £57.37 £114.74 1 X MRE96A REAR END ASSEMBLY D.H.C. £889.93 £889.93

Bulkhead £4,703.27Parts Total Excl Bulkhead £5,738.98Labour For Assembly £3,750.00Total Sub Assembly Cost £14,192.25

08/2015Pool Road,Camphill Industrial Estate,Nuneaton, WarwickshireCV10 9AE EnglandTELEPHONE No. +44 (024) 76 386903FAX No. +44 (024) 76 345302E-MAIL [email protected] www.martinrobey.comCOMPANY REG No. 1980684VAT REG No. GB 487 666 775

SUB ASSEMBLY UNIT FOR SER.14.2 ROADSTER WITH REAR END ASSEMBLY

Qty Part Number Description Individual Price Combined Price 1 x BULKHEAD BULK HEAD UNIT INCLUDING SKUTTLE PANEL £4,703.21 £4,703.21 2 x BD16008F/R FUEL TANK MTG BRACKET £16.15 £32.30 1 x BD27181 FUEL PUMP MTG BRACKET £19.11 £19.11 2 x MRE10LH/RH SIDE FRAME LOWER MTG BRACKETS £38.70 £77.40 1 x MRE112C TRANSMISSION TUNNEL SIDE PANELS SER.1 £62.81 £62.81 1 x MRE112D TRANSMISSION TUNNEL SIDE PANELS SER.1 £62.81 £62.81 1 x MRE115 TUNNEL STIFFENER £47.92 £47.92 2 x MRE117LH/RH STIFFENERS £40.99 £81.98 2 x MRE118LH/RH CLOSING PANEL £22.41 £44.82 1 x MRE119A CENTRAL TUNNEL FACING SER.2 £68.59 £68.59 1 x MRE120RH TUNNEL FORWARD SIDE £103.66 £103.66 1 x MRE120LH TUNNEL FWD SIDE £103.66 £103.66 2 x MRE121LH/RH INNER PEDAL SIDE £13.23 £26.46 2 x MRE122LH/RH OUTER PEDAL £13.06 £26.12 2 x MRE14LH/RH FULL FLOOR £210.42 £420.84 2 x MRE15LH/RH INNER SILLS £81.10 £162.20 2 x MRE19 FRONT STIFFENERS £17.81 £35.62 2 x MRE20LH/RH REAR STIFFENERS £17.81 £35.62 1 x MRE25A CROSSMEMBER SLANT FULL £68.11 £68.11 2 x MRE29LH/RH INN ARCH LH £255.93 £511.86 2 x MRE2LH/RH BHD TO SILL £21.29 £42.58 2 x MRE30LH/RH DOOR SHUT PANEL SER.2 £41.75 £83.50 1 x MRE3RH BULKHEAD PANEL £37.58 £37.58 1 x MRE42 CLOSING PANEL SER.1 DHC £61.02 £61.02 1 x MRE4LH BULKHEAD PANEL 4.2 EARLY £37.58 £37.58 1 x MRE58 UPPER FLOOR £293.96 £293.96 2 x MRE59LH/RH FLOOR STIFFENER BRACKETS £23.61 £47.22 1 x MRE60 TUNNEL ASSEMBLY £224.51 £224.51 1 x MRE61 TOP PANNEL REAR FLOOR £77.26 £77.26 1 x MRE62A PANEL TO BOOT FLOOR 4.2 £59.50 £59.50 1 x MRE63 PANEL ASSEMBLY £86.52 £86.52 1 x MRE64 REAR BULKHEAD £170.06 £170.06 1 x MRE65 REINFORCED CHANNEL £146.54 £146.54 1 x MRE66 REINFORCING CHANNEL TONNEAU £114.79 £114.79 2 x MRE68LH/RH INN VALANCE £140.83 £281.66 2 x MRE69LH/RH ARCH FWD £135.53 £271.06 2 x MRE71LH/RH TOP PANEL INNER £77.61 £155.22 2 x MRE72LH/RH REAR CHASSIS LEGS £230.36 £460.72 2 x MRE73A RADIUS ARM CUPS (RIVETED) £50.01 £100.02 2 x MRE76LH/RH INNER PANEL DOOR SHUT FACE £57.37 £114.74 2 x MRE9ALH/ARH BULKHEAD D PANEL £15.59 £31.18 1 x MRE96A REAR END ASSY D.H.C. £889.93 £889.93

Bulkhead £4,703.21 Parts Total Excl Bulhead £5,779.04 Labour For Assembly £3,750.00 Total Sub Assembly Cost £14,232.25

ALL PRICES SUBJECT TO VAT AS APPLICABLE AND IN GBP The above are mostly welded in place except for some items that may require slight adjustment before welding.This Assembly is Jig Built and can be supplied with a Kit of Outer Body Panels that are not Fitted to the above Sub As-sembly. SUB ASSEMBLY WITHOUT BULKHEAD £9,529.04SUB ASSEMBLY WITH BULKHEAD £14,232.25

3.8 shown for illustration only.Unit Fitted

With Inner Sill Reinforcings


SUB ASSEMBLY UNIT FOR SER.24.2 ROADSTER WITH REAR END ASSEMBLY

Qty Part Number Description Individual Price Combined Price 1 x BULKHEAD BULK HEAD UNIT INCLUDING SKUTTLE PANEL £4,707.27 £4,707.27 2 x BD16008F/R FUEL TANK MTG BRACKET £16.15 £32.30 1 x BD27181 FUEL PUMP MTG BRACKET £19.11 £19.11 2 x MRE10LH/RH SIDE FRAME LOWER MTG BRACKETS £38.70 £77.40 1 x MRE112C TRANSMISSION TUNNEL SIDE PANELS SER.2 £62.81 £62.81 1 x MRE112E TRANSMISSION TUNNEL SIDE PANELS SER.2 £62.81 £62.81 1 x MRE115 TUNNEL STIFFENER £47.92 £47.92 2 x MRE117LH/RH STIFFENERS £40.99 £81.98 2 x MRE118LH/RH CLOSING PANEL £22.41 £44.82 1 x MRE119A CENTRAL TUNNEL FACING SER.2 £68.59 £68.59 1 x MRE120RH TUNNEL FORWARD SIDE £103.66 £103.66 1 x MRE120LH TUNNEL FWD SIDE £103.66 £103.66 2 x MRE121LH/RH INNER PEDAL SIDE £13.23 £26.46 2 x MRE122LH/RH OUTER PEDAL £13.06 £26.12 2 x MRE14LH/RH FULL FLOOR £210.42 £420.84 2 x MRE15LH/RH INNER SILLS £81.10 £162.20 2 x MRE19 FRONT STIFFENERS £17.81 £35.62 2 x MRE20LH/RH REAR STIFFENERS £17.81 £35.62 1 x MRE25A CROSSMEMBER SLANT FULL £68.11 £68.11 2 x MRE29LH/RH INN ARCH LH £255.93 £511.86 2 x MRE2LH/RH BHD TO SILL £21.29 £42.58 2 x MRE32LH/RH DOOR SHUT PANEL SER.2 £65.39 £130.78 1 x MRE3RH BULKHEAD PANEL £37.58 £37.58 1 x MRE42 CLOSING PANEL SER.1 DHC £61.02 £61.02 1 x MRE4LH BULKHEAD PANEL 4.2 EARLY £37.58 £37.58 1 x MRE58 UPPER FLOOR £293.96 £293.96 2 x MRE59LH/RH FLOOR STIFFENER BRACKETS £23.61 £47.22 1 x MRE60 TUNNEL ASSEMBLY £224.51 £224.51 1 x MRE61 TOP PANNEL REAR FLOOR £77.26 £77.26 1 x MRE62A PANEL TO BOOT FLOOR 4.2 £59.50 £59.50 1 x MRE63 PANEL ASSEMBLY £86.52 £86.52 1 x MRE64 REAR BULKHEAD £170.06 £170.06 1 x MRE65 REINFORCED CHANNEL £146.54 £146.54 1 x MRE66 REINFORCING CHANNEL TONNEAU £114.79 £114.79 2 x MRE68LH/RH INN VALANCE £140.83 £281.66 2 x MRE69LH/RH ARCH FWD £135.53 £271.06 2 x MRE71LH/RH TOP PANEL INNER £77.61 £155.22 2 x MRE72LH/RH REAR CHASSIS LEGS £230.36 £460.72 2 x MRE73A RADIUS ARM CUPS (RIVETED) £50.01 £100.02 2 x MRE76LH/RH INNER PANEL DOOR SHUT FACE £57.37 £114.74 2 x MRE9ALH/ARH BULKHEAD D PANEL £15.59 £31.18 1 x MRE96C REAR END ASSY D.H.C. £889.93 £889.93


ALL PRICES SUBJECT TO VAT AS APPLICABLE AND IN GBP The above are mostly welded in place except for some items that may require slight adjustment before welding.This Assembly is Jig Built and can be supplied with a Kit of Outer Body Panels that are not Fitted to the above Sub As-sembly. SUB ASSEMBLY WITHOUT BULKHEAD £9,584.32SUB ASSEMBLY WITH BULKHEAD £14,291.59




SUB ASSEMBLY UNIT FOR JAGUAR E TYPE SER.1 3.8 FIXED HEAD COUPE


1 x BULKHEAD BULK HEAD UNIT INCLUDING SKUTTLE PANEL £4,703.27 £4,703.27 2 x MRE10LH/RH SIDE FRAME LOWER MTG BRACKETS £38.70 £77.40 2 x MRE112ALH/BRH TRANSMISSION TUNNEL SIDE PANELS £62.81 £125.62 1 x MRE115 TUNNEL STIFFENER £47.92 £47.92 2 x MRE117LH/RH STIFFENERS £40.99 £81.98 2 x MRE118ALH CLOSING PANEL LH £18.69 £37.38 1 x MRE118ARH CLOSING PANEL £18.69 £18.69 2 x MRE14LH/RH FULL FLOOR £210.42 £420.84 2 x MRE15LH/RH INNER SILLS £81.10 £162.20 2 x MRE19 FRONT STIFFENERS £17.81 £35.62 2 x MRE20LH/RH REAR STIFFENERS £17.81 £35.62 1 x MRE24A CROSSMEMBER TO FULL FLOOR £68.01 £68.01 2 x MRE28LH/RH INNER WHEEL ARCH SECTION FORWARD £177.99 £355.98 2 x MRE29BLH/RH INN ARCH LH £266.98 £533.96 2 x MRE2LH/RH BHD TO SILL £21.29 £42.58 2 x MRE30LH/RH DOOR SHUT PANEL FHC £41.75 £83.50 1 x MRE3RH BULKHEAD PANEL £37.58 £37.58 1 x MRE42 CLOSING PANEL SER.1 £61.02 £61.02 1 x MRE4LH BULKHEAD PANEL £37.58 £37.58 1 x MRE58 UPPER FLOOR £293.96 £293.96 2 x MRE59LH/RH FLOOR STIFFENER BRACKETS £23.61 £47.22 1 x MRE60 TUNNEL ASSEMBLY £224.51 £224.51 1 x MRE61 TOP PANNEL REAR FLOOR £77.26 £77.26 1 x MRE62 PANEL TO BOOT FLOOR £59.50 £59.50 1 x MRE63 PANEL ASSEMBLY £86.52 £86.52 2 x MRE72LH/RH REAR CHASSIS LEGS £230.36 £460.72 2 x MRE73A RADIUS ARM CUPS (RIVETED IN POSITION) £50.01 £100.02 2 x MRE76ALH/RH INN SHUT RH/LH £62.91 £125.82 2 x MRE78LH/RH INN VALANCE LH £387.41 £774.82 1 x MRE96B REAR END ASSEMBLY, COMPLETE WITH BOOT FLOOR

NUMBER PLATE PANEL ETC SER.1 FHC £889.93 £889.93

2 x MRE9ARH/ALH FRONT INNER BULKHEAD PABEL £15.39 £30.78 2 x MRE9BLH/BRH INNER BULKHEAD PANEL SIDE £44.18 £88.36 1 x MRE43 REAR CLOSING PANEL £59.80 £59.80


ALL PRICES SUBJECT TO VAT AS APPLICABLE AND IN GBP The above are mostly welded in place except for some items that may require slight adjustment before welding.This Assembly is Jig Built and can be supplied with a Kit of Outer Body Panels that are not Fitted to the above Sub Assembly. SUB ASSEMBLY WITHOUT BULKHEAD £ 8,832.70SUB ASSEMBLY WITH BULKHEAD £13,535.97 3.8 shown for illustration only.





1 x BULKHEAD BULK HEAD UNIT INCLUDING SKUTTLE PANEL £4,703.27 £4,703.27 2 x MRE10LH/RH SIDE FRAME LOWER MTG BRACKETS £38.70 £77.40 2 x MRE112C/D TRANSMISSION TUNNEL SIDE PANELS £62.81 £125.62 1 x MRE115 TUNNEL STIFFENER £47.92 £47.92 2 x MRE117LH/RH STIFFENERS £40.99 £81.98 2 x MRE118ALH CLOSING PANEL LH £18.69 £37.38 1 x MRE118ARH CLOSING PANEL £18.69 £18.69 2 x MRE14LH/RH FULL FLOOR £210.42 £420.84 2 x MRE15LH/RH INNER SILLS £81.10 £162.20 2 x MRE19 FRONT STIFFENERS £17.81 £35.62 2 x MRE20LH/RH REAR STIFFENERS £17.81 £35.62 1 x MRE25A CROSSMEMBER TO FULL FLOOR £68.11 £68.11 2 x MRE28LH/RH INNER WHEEL ARCH SECTION FORWARD £177.99 £355.98 2 x MRE29BLH/RH INN ARCH LH £266.98 £533.96 2 x MRE2LH/RH BHD TO SILL £21.29 £42.58 2 x MRE30LH/RH DOOR SHUT PANEL FHC £41.75 £83.50 1 x MRE3RH BULKHEAD PANEL £37.58 £37.58 1 x MRE42 CLOSING PANEL SER.1 £61.22 £61.22 1 x MRE4LH BULKHEAD PANEL £37.88 £37.88 1 x MRE58 UPPER FLOOR £279.96 £279.96 2 x MRE59LH/RH FLOOR STIFFENER BRACKETS £23.61 £47.22 1 x MRE60 TUNNEL ASSEMBLY £224.51 £224.51 1 x MRE61 TOP PANNEL REAR FLOOR £77.26 £77.26 1 x MRE62 PANEL TO BOOT FLOOR £59.50 £59.50 1 x MRE63 PANEL ASSEMBLY £86.52 £86.52 2 x MRE72LH/RH REAR CHASSIS LEGS £230.56 £461.12 2 x MRE73A RADIUS ARM CUPS (RIVETED IN POSITION) £50.01 £100.02 2 x MRE76ALH/RH INN SHUT RH/LH £62.91 £125.82 2 x MRE78LH/RH INN VALANCE LH £387.41 £774.82 1 x MRE96B REAR END ASSEMBLY, COMPLETE WITH BOOT FLOOR




ALL PRICES SUBJECT TO VAT AS APPLICABLE AND IN GBP The above are mostly welded in place except for some items that may require slight adjustment before welding.This Assembly is Jig Built and can be supplied with a Kit of Outer Body Panels that are not Fitted to the above Sub Assembly. SUB ASSEMBLY WITHOUT BULKHEAD £ 8,820.10SUB ASSEMBLY WITH BULKHEAD £ 13,523.37 3.8 shown for illustration only.




ALL PRICES SUBJECT TO VAT AS APPLICABLE AND IN GBP The above are mostly welded in place except for some items that may require slight adjustment before welding.This Assembly is Jig Built and can be supplied with a Kit of Outer Body Panels that are not Fitted to the above Sub As-sembly. SUB ASSEMBLY WITHOUT BULKHEAD £ 8,819.86SUB ASSEMBLY WITH BULKHEAD £13,523.13



Qty Part Number Description Individual Price Combined Price 1 x BULKHEAD BULK HEAD UNIT INCLUDING SKUTTLE PANEL £4,703.27 £4,703.27 2 x MRE10LH/RH SIDE FRAME LOWER MTG BRACKETS £38.70 £77.40 2 x MRE112C/E TRANSMISSION TUNNEL SIDE PANELS £62.81 £125.62 1 x MRE115 TUNNEL STIFFENER £47.92 £47.92 2 x MRE117LH/RH STIFFENERS £40.99 £81.98 2 x MRE118ALH CLOSING PANEL LH £18.69 £37.38 1 x MRE118ARH CLOSING PANEL £18.69 £18.69 2 x MRE14LH/RH FULL FLOOR £210.42 £420.84 2 x MRE15LH/RH INNER SILLS £81.10 £162.20 2 x MRE19 FRONT STIFFENERS £17.81 £35.62 2 x MRE20LH/RH REAR STIFFENERS £17.81 £35.62 1 x MRE25A CROSSMEMBER TO FULL FLOOR £68.11 £68.11 2 x MRE28LH/RH INNER WHEEL ARCH SECTION FORWARD £177.99 £355.98 2 x MRE29BLH/RH INN ARCH LH £266.98 £533.96 2 x MRE2LH/RH BHD TO SILL £21.29 £42.58 2 x MRE32LH/RH DOOR SHUT PANEL FHC £65.59 £131.18 1 x MRE3RH BULKHEAD PANEL £37.58 £37.58 1 x MRE4LH BULKHEAD PANEL £37.58 £37.58 1 x MRE58 UPPER FLOOR £293.96 £293.96 2 x MRE59LH/RH FLOOR STIFFENER BRACKETS £23.61 £47.22 1 x MRE60 TUNNEL ASSEMBLY £224.51 £224.51 1 x MRE61 TOP PANNEL REAR FLOOR £77.26 £77.26 1 x MRE62 PANEL TO BOOT FLOOR £59.50 £59.50 1 x MRE63 PANEL ASSEMBLY £86.52 £86.52 2 x MRE72LH/RH REAR CHASSIS LEGS £230.36 £460.72 2 x MRE73A RADIUS ARM CUPS (RIVETED IN POSITION) £50.01 £100.02 2 x MRE76ALH/RH INN SHUT RH/LH £62.91 £125.82 2 x MRE78LH/RH INN VALANCE LH £387.41 £774.82 1 x MRE96C REAR END ASSEMBLY, COMPLETE WITH BOOT FLOOR





ALPHA PANEL KIT SERIES 1 3.8 & 4.2 ROADSTER


2 X MRE1LH/RH SILL END CLOSING PANELS 14.74 29.48

2 X MRE2LH/RH BULKHEAD TO SILL PANELS 21.29 42.58

2 X MRE5-6 BATT-AIR CLEANER MTG BKTS 16.26 32.52

2 X MRE9LH/RH BULKHEAD SIDE PANELS 51.58 103.16

2 X MRE17LH/RH OUTER SILLS 85.52 171.04

2 X MRE38LH/RH STIFFENERS FROM LOWER QTRS TO No. PLATE 18.74 37.48

1 X MRE44A REAR TONNEAU PANEL 171.72 171.72

1 X MRE67 TONNEAU TOP PANELS 119.15 119.15

2 X MRE70LH/RH TOP PANEL TO HOOD 50.77 101.54

1 X MRE75LH REAR OUTER WING 523.49 523.49

1 X MRE75RH REAR OUTER WING 523.49 523.49

2 X MRE98LH/RH REAR LIGHT FILLETS 50.56 101.12

1 X BD15933 FUEL FILLER BOX 204.24 204.24

2 X BD19532-33 MOUNTING BRACKETS 6.74 13.48


Total Excluding VAT £2,187.57

VAT @ 20% £437.51

Total Inc. VAT £2,625.08

ALL PRICES CORRECT AT TIME OF PRINTING BUT SUBJECT TO ALTERATIONS WITHOUT PRIOR NOTICE


ALPHA PANEL KIT SERIES 1 3.8 & 4.2 FIXED HEAD COUPE








1 X MRE44 REAR TONNEAU PANEL 171.72 171.72

1 X MRE75ALH REAR OUTER WING 785.24 785.24

1 X MRE75ARH REAR OUTER WING 785.24 785.24

2 X MRE98LH/RH REAR LIGHT FILLETS 50.56 101.12





VAT @ 20% £498.48




ALPHA PANEL KIT SERIES 2 4.2 ROADSTER







1 X MRE44C REAR TONNEAU PANEL 207.06 207.06





2 X BD35684/3 REAR LIGHT FILLETS 73.65 147.3


2 X BD35620/1 MOUNTING BRACKETS 9.32 18.64

Total Excluding VAT £ 2,173.32

VAT @ 20% £ 434.66

Total Inc. VAT £ 2,607.98









1 X MRE44B REAR TONNEAU PANEL 150.79 150.79





2 X BD35620/1 MOUNTING BRACKET 9.32 18.64


VAT @ 20% £ 493.97


ALPHA PANEL KIT SERIES 2 4.2 FIXED HEAD COUPE



BETA PANEL KIT SERIES 1 3.8 & 4.2 ROADSTER


2 X MRE1LH/RH SILL END CLOSING PANELS £14.74 £29.48

2 X MRE2LH/RH BULKHEAD TO SILL PANELS £21.29 £42.58

2 X MRE5-6 BATT-AIR CLEANER MTG BKTS £16.26 £32.52

2 X MRE9LH/RH BULKHEAD SIDE PANELS £51.58 £103.16

2 X MRE17LH/RH OUTER SILLS £86.52 £173.04

2 X MRE38LH/RH STIFFENERS FROM LOWER QTRS TO No. PLATE £18.74 £37.48

1 X MRE44A REAR TONNEAU PANEL £171.72 £171.72

1 X MRE67 TONNEAU TOP PANELS £119.15 £119.15

2 X MRE70LH/RH TOP PANEL TO HOOD £50.77 £101.54

1 X MRE75LH REAR OUTER WING £523.49 £523.49

1 X MRE75RH REAR OUTER WING £471.12 £471.12

2 X MRE98LH/RH RREAR LIGHT FILLETS £50.56 £101.12

1 X BD15933 FUEL FILLER BOX £204.24 £204.24

2 X BD19532-33 MOUNTING BRACKETS £6.74 £13.48

2 X BD25409-10 MOUNTING BRACKETS £6.54 £13.08

2 X MRE79ALH/RH DOOR COMPLETE £733.99 £1,467.98

1 X MRE104A BOOTLID £484.90 £484.90


VAT @ 20% £ 818.02




BETA PANEL KIT SERIES 1 3.8 & 4.2 FIXED HEAD COUPE











2 X MRE98LH/RH RREAR LIGHT FILLETS 50.56 101.12




2 X MRE79BLH/RH DOOR COMPLETE 733.99 1467.98


VAT @ 20% £ 791.60




BETA PANEL KIT SERIES 2 4.2 ROADSTER















2 X MRE79CLH/RH DOOR COMPLETE 733.99 1467.98

1 x MRE104A BOOT LID 484.9 484.9


VAT @ 20% £825.24




BETA PANEL KIT SERIES 2 4.2 FIXED HEAD COUPE














2 X MRE79DLH/RH DOOR COMPLETE 733.99 1467.98


VAT @ 20% £ 808.35




DELTA PANEL KIT SERIES 1 3.8 & 4.2 ROADSTER








1 X MRE44A REAR TONNEAU PANEL 171.72 171.72









2 X MRE79ALH/RH DOOR COMPLETE 733.99 1467.98

1 X MRE104A BOOTLID 484.9 484.9

1 X BD36166 BONNET COMPLETE 5424.32 5424.32


VAT @ 20% £ 1,902.88




DELTA PANEL KIT SERIES 1 3.8 & 4.2 FIXED HEAD COUPE















2 X MRE79BLH/RH DOOR COMPLETE 733.99 1467.98

1 X MRE104A BOOT LID ASSEMBLY 484.9 484.9



VAT @ 20% £ 1,973.44




DELTA PANEL KIT SERIES 2 4.2 ROADSTER















2 X MRE79CLH/RH DOOR COMPLETE 733.99 1467.98

1 X MRE104A BOOT LID ASSEMBLY 484.9 484.9



VAT @ 20% £ 1,895.37




DELTA PANEL KIT SERIES 2 4.2 FIXED HEAD COUPE












2 X MRE79DLH/RH DOOR COMPLETE 733.99 1467.98



VAT @ 20% £ 1,842.96



08/2015

Documents

08/2015 - Martin Robey · PDF file · 2015-10-0908/2015 Martin Robey Engineering ... Series 1 and Series 2-3 E-type models , ... 2 X MRE10LH/RH SIDE FRAME LOWER MTG BRACKETS £38.70