1. 2 Console Connectivity RJ-45 Connector Console Port Computer Rollover Cable RJ-45 to DB-9 Converter

1

2

Console Connectivity

RJ-45 Connector

Console Port

ComputerRollover Cable

RJ-45 to DB-9Converter

3


• Connect a rollover cable to the router console port (RJ-45 connector).

• Connect the other end of the rollover cable to the RJ-45 to DB-9 converter

• Attach the female DB-9 converter to a PC Serial Port.

• Open emulation software on the PC.

4

Emulation Software

WINDOWS

• Start Programs Accessories Communications HyperTerminal HyperTerminal.

• Give the Connection Name & Select Any Icon

• Select Serial (Com) Port where Router is Connected.

• In Port Settings Click on Restore Defaults

5


E0

LAN - 192.168.1.0/24

Con 0

6

7

8

9

10

11

12

13

abc

14

15

16

17

18

19

System Bootstrap, Version 11.0(10c), SOFTWARECopyright (c) 1986-1996 by cisco Systems2500 processor with 2048 Kbytes of main memory

Notice: NVRAM invalid, possibly due to write erase.F3: 5575260+78596+410108 at 0x3000060

Restricted Rights Legend

Use, duplication, or disclosure by the Government issubject to restrictions as set forth in subparagraph(c) of the Commercial Computer Software - RestrictedRights clause at FAR sec. 52.227-19 and subparagraph(c) (1) (ii) of the Rights in Technical Data and ComputerSoftware clause at DFARS sec. 252.227-7013.

Cisco Systems, Inc. 170 West Tasman DriveSan Jose, California 95134-1706

20

Cisco Internetwork Operating System Software IOS(tm) 2500 Software(C2500-P-L),Version 12.1(24),RELEASE SOFTWARE(fc1Copyright (c) 1986-2002 by cisco Systems, Inc.Compiled Mon 30-Sep-02 20:43 by sraniImage text-base: 0x0302EA54, data-base: 0x00001000

Cisco 2500(68030)processor(revision N) with 2048K/2048K bytes of memoryProcessor board ID 11169613, with hardware revision 00000001X.25 software, Version 3.0.0.Basic Rate ISDN software, Version 1.1.1 Ethernet/IEEE 802.3 interface(s)2 Serial network interface(s)1 ISDN Basic Rate interface(s)32K bytes of non-volatile configuration memory.16384K bytes of processor board System flash (Read ONLY)

--- System Configuration Dialog ---

Would you like to enter the initial configuration dialog? [yes/no]: n

21

Press RETURN to get started!00:00:20: %LINK-3-UPDOWN: Interface Ethernet0, changed state to up00:00:20: %LINK-3-UPDOWN: Interface Serial0, changed state to down00:00:20: %LINK-3-UPDOWN: Interface Serial1, changed state to down00:00:21: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed state to up00:00:21: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to down00:00:21: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state to down00:12:43: %LINK-5-CHANGED: Interface Ethernet0, changed state to administratively down00:12:43: %LINK-5-CHANGED: Interface Serial0, changed state to administratively down00:12:43: %LINK-5-CHANGED: Interface Serial1, changed state to administratively down00:12:44: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed state to down00:12:46: %SYS-5-RESTART: System restarted

22

Cisco Internetwork Operating System Software IOS(tm) 2500 Software(C2500-P-L),Version 12.1(24),RELEASE SOFTWARE(fc1Copyright (c) 1986-2002 by cisco Systems, Inc.Compiled Mon 30-Sep-02 20:43 by sraniRouter>enableRouter# show running-config

User ModeUser Mode

Privileged ModePrivileged Mode

Current configuration:!version 12.1no service password-encryptionno service udp-small-serversno service tcp-small-servers!hostname Router!interface Ethernet0 no ip address shutdown--More--

.....Building configuration

23

interface Serial0 no ip address shutdown!interface Serial1 no ip address shutdown!no ip classless!!line con 0line aux 0line vty 0 4 login!endRouter# show startup-config% Non-volatile configuration memory has not been set up or bad checksumRouter#

24

show flashSystem flash directory:File Length Name/status 1 8108960 /c2500-ipx-ip.bin[8109024 bytes used, 8668192 available, 16777216 total]16384K bytes of processor board System flash (Read ONLY)

Router#

Router#

Cisco Internetwork Operating System SoftwareIOS (tm) 2500 Software (C2500-JS-L),Version 12.1(17),RELEASE SOFTWARECopyright (c) 1986-1999 by cisco Systems, Inc.Compiled Mon 04-Jan-99 17:27 by ashahImage text-base: 0x03040148, data-base: 0x00001000

ROM: System Bootstrap, Version 11.0(10c), SOFTWAREBOOTFLASH: 3000 Bootstrap Software (IGS-BOOT-R), Version 11.0(10c), RELEASE SOFTWARE (fc1)

--More--

show version

25

Router uptime is 1 hour, 28 minutesSystem restarted by power-onSystem image file is "flash:/c2500-ipx-ip.bin", booted via flash

Cisco 2500(68030)processor(revision N) with 2048K/2048K bytes of memoProcessor board ID 11169613, with hardware revision 00000001X.25 software, Version 3.0.0.Basic Rate ISDN software, Version 1.1.1 Ethernet/IEEE 802.3 interface(s)2 Serial network interface(s)1 ISDN Basic Rate interface(s)32K bytes of non-volatile configuration memory.16384K bytes of processor board System flash (Read ONLY)

Configuration register is 0x2102

Router#configure terminalEnter configuration commands, one per line. End with CNTL/Z.Router(config)# hostname Hyderabad

Global Configuration ModeGlobal Configuration Mode

Hyderabad(config)#

26

Hyderabad(config)# interface ethernet 0Hyderabad(config-if)#ip address 192.168.1.150 255.255.255.0Hyderabad(config-if)# no shutdownHyderabad(config-if)# exitHyderabad(config)# line vty 0 4Hyderabad(config-line)# loginHyderabad(config-line)# password netmetric

Hyderabad(config)# line con 0 Hyderabad(config-line)# loginHyderabad(config-line)# password ccna

Hyderabad(config-line)# exit

Configuring Ethernet interfaceRouter(config)# interface ethernet <no.>Router(config-if)# ip address <address><mask>Router(config-if)# no shutdown

Configuring Ethernet interfaceRouter(config)# interface ethernet <no.>Router(config-if)# ip address <address><mask>Router(config-if)# no shutdown

Setting Console passwordRouter(config)# line con 0 Router(config-line)# loginRouter(config-line)# password <password>

Setting Console passwordRouter(config)# line con 0 Router(config-line)# loginRouter(config-line)# password <password>

Setting Telnet passwordRouter(config)# line vty 0 4Router(config-line)# loginRouter(config-line)# password <password>

Setting Telnet passwordRouter(config)# line vty 0 4Router(config-line)# loginRouter(config-line)# password <password>

terface ModeIn

terface ModeIn

Hyderabad(config)# line aux 0 Hyderabad(config-line)# loginHyderabad(config-line)# password cisco

Hyderabad(config-line)# exit

Setting Auxilary passwordRouter(config)# line aux 0 Router(config-line)# loginRouter(config-line)# password <password>

Setting Auxilary passwordRouter(config)# line aux 0 Router(config-line)# loginRouter(config-line)# password <password>

Hyderabad(config-line)#Hyderabad(config)#

exitenable password cisco

Hyderabad(config)#^ZHyderabad(config)#

Setting the Enable passwordRouter(config)#enable password <password>Router(config)#enable secret <password>

Setting the Enable passwordRouter(config)#enable password <password>Router(config)#enable secret <password>

enable secret netmetric

27

Current configuration:!version 12.1no service password-encryptionno service udp-small-serversno service tcp-small-servers!hostname Hyderabad!enable secret 5 $1$60nw$8XzAJ445GBzx1mgYJTUjo1enable password cisco!interface Ethernet0 ip address 192.168.1.150 255.255.255.0!interface Serial0 no ip addressshutdown--More--

.....Building configurationHyderabad# show running-config

28

interface Serial1 no ip addressshutdown!no ip classless!line con 0 login password ccnaline aux 0 login password ciscoline vty 0 4 login password zoom!endHyderabad# show startup-config% Non-volatile configuration memory has not been set up or bad checksumHyderabad#

29

Hyderabad# copy running-config startup-config

[OK]

Hyderabad# show startup-config

Current configuration:!version 12.1no service password-encryptionno service udp-small-serversno service tcp-small-servers!hostname Hyderabad!enable secret 5 $1$60nw$8XzAJ445GBzx1mgYJTUjo1enable password cisco!interface Ethernet0 ip address 192.168.1.150 255.255.255.0--More--



Saving Router ConfigurationRouter#copy running-config startup-config or Router#write memory orRouter#wr

Saving Router ConfigurationRouter#copy running-config startup-config or Router#write memory orRouter#wr

30

interface Serial0 no ip addressshutdown!interface Serial1 no ip addressshutdown!no ip classless!line con 0 login password ccnaline aux 0 login password ciscoline vty 0 4 login password zoom!endHyderabad#

31


E0

LAN - 192.168.1.0/24

Con 0

32

================================Welcome to Hyderabad Router================================User Access Verificationpassword :****

****enableHyderabad>

password :Hyderabad#

33

telnet 192.168.1.150

================================Welcome to Hyderabad Router================================User Access Verificationpassword :****

****enableHyderabad>

password :Hyderabad#

Microsoft Windows 2000 [Version 5.00.2195](C) Copyright 1985-2000 Microsoft Corp.C:\>Connecting .....

Rick Graziani [email protected] 34

Router>show versionCisco Internetwork Operating System SoftwareIOS (tm) 2500 Software (C2500-D-L), Version 12.0(5), RELEASE SOFTWARE (fc1)Copyright (c) 1986-1999 by cisco Systems, Inc.Compiled Tue 15-Jun-99 20:08 by phanguyeImage text-base: 0x030380DC, data-base: 0x00001000

ROM: System Bootstrap, Version 11.0(10c)XB2, PLATFORM SPECIFIC RELEASE SOFTWARE(fc1)BOOTFLASH: 3000 Bootstrap Software (IGS-BOOT-R), Version 11.0(10c)XB2, PLATFORMSPECIFIC RELEASE SOFTWARE (fc1)

Router uptime is 49 minutesSystem restarted by reloadSystem image file is "flash:c2500-d-l_120-5.bin"

cisco 2516 (68030) processor (revision J) with 6144K/2048K bytes of memory.Processor board ID 10375144, with hardware revision 00000001Bridging software.X.25 software, Version 3.0.0.Basic Rate ISDN software, Version 1.1.1 Ethernet/IEEE 802.3 interface(s)14 Ethernet/IEEE 802.3 repeater port(s)2 Serial network interface(s)1 ISDN Basic Rate interface(s)32K bytes of non-volatile configuration memory.8192K bytes of processor board System flash (Read ONLY)

Configuration register is 0x2102

Router>

Configuration Register, important for password recovery. Must press space or return to get this last line!

IOS Version

ROM Version – not usually an issue

Router boot information

Booted this IOS file from flash

Amount of RAM memory

Router interfaces

Amount of NVRAM

Amount of Flash

Model & CPU

The show version command

Router modes

1. Router>2. Router#3. Router(config)#

4. Router(config-if)#5. Router(config-subif)#6. Router(config-line)#7. Router(config-

router)#

1. User mode2. Privelege mode3. Global configuration

mode.4. Interface mode.5. Subinterface mode.6. Line mode.7. Router configuration

mode

Documents

1. 2 Console Connectivity RJ-45 Connector Console Port Computer Rollover Cable RJ-45 to DB-9 Converter