Embed Size (px)
Citation preview
ERouting EIGRP PT Practice SBA
ERouting EIGRP PT Practice SBA
A few things to keep in mind while completing this activity:
1. Do not use the browser Back button or close or reload any Exam windows during the exam.
2. Do not close Packet Tracer when you are done. It will close automatically. 3. Click the Submit Assessment button to submit your work.
Introduction In this Packet Tracer Practice Skills-based Assessment, you will:
• complete the configuration of a partially configured network
• establish connectivity to the West Region and the Internet through the use of static and dynamic routing
• verify connectivity
Addressing Table
Device Interface Address Subnet Mask Default Gateway
EastHQ
S0/0/0 up 192.168.1.249/30 255.255.255.252 N/A
S0/0/1 do 192.168.1.253/30 255.255.255.252 N/A
S0/1/0 up 209.165.201.6/30 255.255.255.252 Internet
S0/1/1 up 192.0.2.2/30 255.255.255.252 192.0.2.1
E-Branch1
Fa0/0 192.168.0.1 /25 255.255.255.128 N/A
Fa0/1 192.168.0.129 /25 255.255.255.128 N/A
S0/0/0 192.168.1.250 /30 255.255.255.252 N/A
S0/0/1 192.168.1.245 /30 255.255.255.252 N/A
E-Branch2
Fa0/0 192.168.1.1 /26 255.255.255.192 N/A
Fa0/1 192.168.1.65 /26 255.255.255.192 N/A
S0/0/0 192.168.1.254 /30 255.255.255.252 N/A
S0/0/1 192.168.1.246/30 255.255.255.252 N/A
EPC1 NIC 192.168.0.2 /28 255.255.255.128 192.168.0.1
EPC2 NIC 192.168.0.254 255.255.255.252 192.168.0.1
EPC3 NIC 192.168.1.2 /26 255.255.255.192 192.168.1.1
EPC4 NIC 192.168.1.126 255.255.255.192 192.168.1.1
NetAdmin NIC 192.168.1.66 /26 255.255.255.192 192.168.1.65
Note: The password for user EXEC mode is cisco . The password for privileged EXEC mode is class .
Step 1: Configure the Device Basics.
Note: Initially, you can only access router E-Branch2 through the console connection on NetAdmin.
a. Configure the following on E-Branch2:
• The router name is EB2.
Router(config)# hostname EB2
• The privileged EXEC mode uses the following encrypted password: class.
EB2(config)#enable secret class
• Enable Telnet and console line logins and use the following password: cisco.
EB2(config)#line vty 0 4
EB2(config)#password class
EB2(config)#login
EB2(config)#exit
• Configure the banner message-of-the-day as Authorized access only!
EB2(config)#banner motd %Authorized access only!%
b. Using the Addressing Table, configure and activate all the necessary interfaces on E-Branch2.
c. Configure correct host IP addressing.
EB2#show ip interface brief
EB2#show ip route
• Configure EPC2 with the last IP address in the subnet.
192.168.0.254 255.255.255.128
Default gateway 192.168.0.1
• Configure EPC4 with the last IP address in the subnet.
192.168.1.126 255.255.255.192
Default gateway 192.168.1.1
Step 2: Discover the Network.
a. Explore the network to determine the IP address of the serial interface that EastHQ uses to connect to E-Branch2.
b. Remotely access EastHQ.
EB2# show interfaces
EB2# show cdp neighbors
EB2# show ip route
EB2# telnet 192.168.1.253
EastHQ(config)#interface serial0/0/0
EastHQ (config-if)#ip address 192.168.1.249 255.255 .255.252
EastHQ (config-if)#no shutdown
EastHQ (config-if)#exit
EastHQ (config)#interface serial0/0/1
EASTHQ(config-if)#ip address 192.168.1.253 255.255. 255.252
EASTHQ(config-if)#no shutdown
EASTHQ(config-if)#exit
EASTHQ(config)#interface serial0/1/0
EASTHQ(config-if)#ip address 209.165.201.6 255.255. 255.252
EASTHQ(config-if)#no shutdown
EASTHQ(config-if)#exit
EASTHQ(config)#interface serial0/1/1
EASTHQ(config-if)#ip address 192.0.2.2 255.255.255. 252
EASTHQ(config-if)#no shutdown
EASTHQ(config-if)#exit
Step 3: Configure Static and Default Routing.
a. Configure connectivity to the West Region.
• Configure a static route on EastHQ to the entire West Region. The West Region uses the 172.16.100.0/24 address space. Use the next-hop address argument .
EastHQ#show ip route
EastHQ(config)#route ip 172.16.100.0 255.255.255.0 192.0.2.1
• Configure a default route on EastHQ to send to the Internet all other traffic for destinations that are not found in the EastHQ routing table. Use the exit interface argument.
EastHQ(config)#route ip 0.0.0.0 0.0.0.0 serial0/1/0
b. Verify static and default routing.
EastHQ#show ip route
EastHQ#ping
Step 4: Configure EIGRP Routing.
Configure EIGRP on EastHQ, E-Branch1, and E-Branch2.
a. Use AS number 100. b. b.Do not advertise the network between EastHQ and the Internet. c. Do not advertise the network between EastHQ and the West Region. d. Advertise all other attached networks. e. Disable automatic summarization. f. Disable EIGRP updates out interfaces where there are no EIGRP neighbors available. g. On EastHQ, enter the one command in the EIGRP routing process that will propagate the default and static
routes to E-Branch1 and E-Branch2.
EastHQ(config)#router eigrp 100 EastHQ(config-router)#network 192.168.1.248 0.0.0.3 EastHQ(config-router)#network 192.168.1.244 0.0.0.3 EastHQ(config-router)#no auto-summary EastHQ(config-router)# ip default-network EastHQ(config)#interface serial0/1/0 EastHQ(config-if)#no eigrp 100 EastHQ(config)#interface serial0/1/1 EastHQ(config-if)#no eigrp 100 ----------------------------------------- EB1(config)#router eigrp 100 EB1(config-router)#network 192.168.1.0 0.0.0.3 EB1(config-router)#network 192.168.1.0 0.0.0.127` EB1(config-router)#passive-interface fa0/0 EB1(config-router)#passive-interface fa0/1 EB1(config-router)#CTRL+Z ------------------------------------------ EB2(config)#router eigrp 100 EB2(config-router)#network 192.168.1.0 0.0.0.3 EB2(config-router)#network 192.168.1.0 0.0.0.63 EB2(config-router)#passive-interface fa0/0 EB2(config-router)#passive-interface fa0/1 EB2(config-router)#CTRL+Z
Step 5: Modify the default EIGRP operation.
a. Configure the link between EastHQ and E-Branch2 so that the correct bandwidth of 384 k/s is used in EIGRP calculations.
b. Configure E-Branch1 to advertise a summary route for the subnets 192.168.0.0/25 and 192.168.0.128/25 to EastHQ and E-Branch2.
c. Configure E-Branch2 to advertise a summary route for the subnets 192.168.1.0/26 and 192.168.1.64/26 to EastHQ and E-Branch1.
EastHQ(config)#interface s0/0/1 EastHQ(config-if)#bandwidth 384 EastHQ(config-if)#ip bandwidth-percent eigrp 100 10 0 EB2(config)#interface s0/0/0 EB2(config-if)#bandwidth 384 EB2(config-if)#ip bandwidth-percent eigrp 100 100 EB1(config)#router eigrp 100 EB1(router-config)#network 192.168.0.0 0.0.0.3 EB1(router-config)#end EB2(config)#router eigrp 100 EB2(router-config)#network 192.168.1.0 0.0.0.63 EB2(router-config)#end
Step 6: Verify Full Connectivity.
Although these are not scored, the following connectivity tests should be successful.
• Test connectivity to the West Region.
• Test connectivity to the Internet.
Version 1.0 Created in Packet Tracer 5.3.1.0044 and Marvel 1.0.1 All contents are Copyright © 1992 - 2011 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
