Embed Size (px)
Citation preview
ISTIAQUEORBITA SIMPLE WAY OF MY LIFE
Search search
HOME » MY Y STUDY SECTION » CCNA » ROUTER CONFIGURATION » EIGRP EROUTING PT PRACTICE SBA
EIGRP ERouting PT Practice SBARECENT POSTS
50 Challenging
Interview Questions 05/11/2013
Common interview questions &
sample Answer 05/11/2013
Electronics Viva Question
and answer 05/11/2013
Electrical Viva Question and
answer P2 05/11/2013
Electrical Viva Question
and answer 05/11/2013
Mechanical Viva Question
and answer 05/11/2013
CCNA Viva Question and answer
05/11/2013
CCNA 4 Final Exam Question
and Answers 2012 29/06/2013
CCNA 4 Final Exam Question
and Answers 2011 29/06/2013
1.NAT Configuration 22/06/2013
1.DHCP Configuration
22/06/2013
Extended ACL Configuration
22/06/2013
ACL (Access Control List)
20/06/2013
ACL Configuration-1 15/06/2013
Various Configuration
Commands 13/06/2013
Frame Relay Configuration2
06/06/2013
Frame Relay Configuration1
06/06/2013
Protibimber Biborno Kabbo-2
05/06/2013
Protibimber Biborno Kabbo-1
05/06/2013
Router&Switch Configuration-1
01/06/2013
34th BCS Exam and Answer
27/05/2013
Wifi Basic Configuration
25/05/2013
Basic Switching/Wireless PT
Practice SBA 25/05/2013
সমাথ�ক শ� 24/05/2013
িবপরীত শ� 24/05/2013
Switc configuration Practice 5
19/05/2013
Switc configuration Practice 4
16/05/2013
Switc configuration Practice 3
16/05/2013
Switc configuration Practice 2
11/05/2013
Switc configuration Practice 1
11/05/2013
Basic Switch
configurations commands
ERouting EIGRP PT Practice SBA
A few things to keep in mind while completing this activity:
1. Do not use the browser Back button or close or reload any Exam windows during the exam.
2. Do not close Packet Tracer when you are done. It will close automatically.
3. Click the Submit Assessment button to submit your work.
Introduction
In this Packet Tracer Practice Skills-based Assessment, you will:
complete the configuration of a partially configured network
establish connectivity to the West Region and the Internet through the use of static and dynamic routing
verify connectivity
Addressing Table
Device Interface Address Subnet Mask Default Gateway
EastHQ
S0/0/0 N/A
S0/0/1 N/A
S0/1/0 N/A
S0/1/1 N/A
E-Branch1
Fa0/0 192.168.0.1 255.255.255.128 N/A
Fa0/1 192.168.0.129 255.255.255.128 N/A
S0/0/0 192.168.1.250 255.255.255.252 N/A
S0/0/1 192.168.1.245 255.255.255.252 N/A
E-Branch2
Fa0/0 192.168.1.1 255.255.255.192 N/A
Fa0/1 192.168.1.65 255.255.255.192 N/A
S0/0/0 192.168.1.254 255.255.255.252 N/A
S0/0/1 192.168.1.246 255.255.255.252 N/A
Home ABOUT ME STUDY BOOKS TEC CAFE TUTORIAL CATAGORIES SONG HELPS CONTACT LOGIN
10/05/2013
ccna part 3 chapter-7 08/05/2013
ccna part3 chapter-5 08/05/2013
ccna part3 chapter-5 08/05/2013
ccna part3 chapter4 08/05/2013
CCNA PART 3 CHAPTER-3
08/05/2013
About Knowledge 06/05/2013
ccna part 3 chapter 2 06/05/2013
ccna-3 chapter 1 06/05/2013
CCNA 2 Final Exam 2012 v.1
04/05/2013
CCNA Exploration-2: Routing
Protocols and Concepts
(Version 4.0) –Question
and Answer. 03/05/2013
ERouting OSPF PT Practice SBA
28/04/2013
ERouting OSPF PT Practice SBA
26/04/2013
OSPF Election DR BDR ODR
25/04/2013
OSPF Routing Configuration
25/04/2013
EIGRP ERouting PT
Practice SBA 24/04/2013
EIGRP Configuration Test
24/04/2013
VLSM Practice Paper 3
23/04/2013
VLSM Practice Paper 2
23/04/2013
VLSM Practice Paper1
23/04/2013
EPC1 NIC 192.168.0.2 255.255.255.128 192.168.0.1
EPC2 NIC
EPC3 NIC 192.168.1.2 255.255.255.192 192.168.1.1
EPC4 NIC
NetAdmin NIC 192.168.1.66 255.255.255.192 192.168.1.65
Note: The password for user EXEC mode is cisco. The password for privileged EXEC mode is class.
Step 1: Configure the Device Basics.
Note: Initially, you can only access router E-Branch2 through the console connection on NetAdmin.
a. Configure the following on E-Branch2:
· The router name is EB2.
· The privileged EXEC mode uses the following encrypted password: class.
· Enable Telnet and console line logins and use the following password: cisco.
· Configure the banner message-of-the-day as Authorized access only!
b. Using the Addressing Table, configure and activate all the necessary interfaces on E-Branch2.
c. Configure correct host IP addressing.
· Configure EPC2 with the last IP address in the subnet.
· Configure EPC4 with the last IP address in the subnet.
Step 2: Discover the Network.
a. Explore the network to determine the IP address of the serial interface that EastHQ uses to connect to E-Branch2.
b. Remotely access EastHQ.
Step 3: Configure Static and Default Routing.
a. Configure connectivity to the West Region.
· Configure a static route on EastHQ to the entire West Region. The West Region uses the 172.16.100.0/24 addressspace. Use the next-hop address argument.
· Configure a default route on EastHQ to send to the Internet all other traffic for destinations that are not found in theEastHQ routing table. Use the exit interface argument.
b. Verify static and default routing.
Step 4: Configure EIGRP Routing.
Configure EIGRP on EastHQ, E-Branch1, and E-Branch2.
a. Use AS number 100.
b. Do not advertise the network between EastHQ and the Internet.
c. Do not advertise the network between EastHQ and the West Region.
d. Advertise all other attached networks.
e. Disable automatic summarization.
f. Disable EIGRP updates out interfaces where there are no EIGRP neighbors available.
g. On EastHQ, enter the one command in the EIGRP routing process that will propagate the default and static routes to E-Branch1 and E-Branch2.
Step 5: Modify the default EIGRP operation.
a. Configure the link between EastHQ and E-Branch2 so that the correct bandwidth of 384 k/s is used in EIGRP calculations.
b. Configure E-Branch1 to advertise a summary route for the subnets 192.168.0.0/25 and 192.168.0.128/25 to EastHQ and E-Branch2.
c. Configure E-Branch2 to advertise a summary route for the subnets 192.168.1.0/26 and 192.168.1.64/26 to EastHQ and E-Branch1.
Step 6: Verify Full Connectivity.
Although these are not scored, the following connectivity tests should be successful.
· Test connectivity to the West Region.
· Test connectivity to the Internet.
Form B
Created in Packet Tracer 5.3.2.0027 and Marvel 1.0.1
All contents are Copyright © 1992 – 2011 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
SOLUTION:
Step1:
a)
Router(config)#hostname EB2
EB2(config)#enable secret class
EB2(config)#line console 0
EB2(config-line)#password cisco
EB2(config-line)#login
EB2(config-line)#exit
EB2(config)#line vty 0 4
EB2(config-line)#pas
EB2(config-line)#password cisco
EB2(config-line)#login
EB2(config-line)#exit
EB2(config)#banner motd #
Enter TEXT message. End with the character ‘#’.
Authorized access only! #
b)
EB2(config)#interface fastEthernet0/0
EB2(config-if)#ip address 192.168.1.1 255.255.255.192
EB2(config-if)#no shutdown
EB2(config)#interface fastEthernet 0/1
EB2(config-if)#ip address 192.168.1.65 255.255.255.192
EB2(config-if)#no shutdown
EB2(config)#interface serial 0/0/0
EB2(config-if)#ip address 192.168.1.254 255.255.255.252
EB2(config-if)#no shutdown
EB2(config)#interface serial 0/0/1
EB2(config-if)#ip address 192.168.1.246 255.255.255.252
EB2(config-if)#no shutdown
c)Configure correct host IP addressing.
EPC2- Given-192.168.0.128/25—–>192.168.0. 1/_ _ _ _ _ _ _
So,NA-192.168.0.128
BA-192.168.0.255
SM-255.255.255.128
Now.accroding to question Configure EPC2 with the last IP address in the subnet.
IP-192.168.0.254
SM-255.255.255.128
GA-192.168.0.129 jast 1st host address
EPC4- Given-192.168.1.64/26—–>192.168.1. 0 1/_ _ _ _ _ _
So,NA-192.168.1.64
BA-192.168.1.127
SM-255.255.255.192
Now.accroding to question Configure EPC2 with the last IP address in the subnet.
IP-192.168.0.126
SM-255.255.255.192
GA-192.168.0.65 jast 1st host address
Step 2::
a.Explore the network to determine the IP address of the serial interface that EastHQ uses to connect to E-Branch2.
b.Remotely access EastHQ.
a)
EB2#show interface
EB2#show ip route
EB2#show cdp neighbors detail
Entry address(es):
IP address : 192.168.1.253
Platform: cisco C1841, Capabilities: Router
Interface: Serial0/0/0, Port ID (outgoing port): Serial0/0/1
Holdtime: 148
b)
EB2#telnet 192.168.1.253
Trying 192.168.1.253 …OpenAuthorized Access Only!
Step 3::
a)
For next-hop address:
EastHQ#show cdp neighbors detail
Device ID: WHQ
Entry address(es):
IP address : 192.0.2.1
Platform: cisco C1841, Capabilities: Router
Interface: Serial0/1/1, Port ID (outgoing port): Serial0/1/1
Holdtime: 165
EastHQ#show ip interface brief
EastHQ#show run
interface Serial0/1/1
ip address 192.0.2.2 255.255.255.252
EastHQ(config)#ip route 172.16.100.0 255.255.255.0 192.0.2.1
EastHQ(config)#ip route 0.0.0.0 0.0.0.0 serial 0/1/0
b)For verify static and default routing.
EastHQ#show run
EastHQ#show ip route
Step4::
Configure EIGRP on EastHQ, E-Branch1, and E-Branch2.
a.Use AS number 100.
b.Do not advertise the network between EastHQ and the Internet.
c.Do not advertise the network between EastHQ and the West Region.
d.Advertise all other attached networks.
e.Disable automatic summarization.
f.Disable EIGRP updates out interfaces where there are no EIGRP neighbors available.
g.On EastHQ, enter the one command in the EIGRP routing process that will propagate the default and static routes
to E-Branch1 and E-Branch2.
EastHQ#conf t
EastHQ(config)#router eigrp 100
EastHQ(config-router)#network 192.168.1.248 0.0.0.3
EastHQ(config-router)#network 192.168.1.252 0.0.0.3
EastHQ(config-router)#no auto-summary
EastHQ(config-router)#redistribute static
EB1#conf t
EB1(config)#router eigrp 100
EB1(config-router)#network 192.168.1.248 0.0.0.3
EB1(config-router)#network 192.168.1.244 0.0.0.3
EB1(config-router)#network 192.168.0.0 0.0.0.127
EB1(config-router)#network 192.168.0.128 0.0.0.127
EB1(config-router)#no auto-summary
EB1(config-router)#passive-interface fastEthernet 0/0
EB1(config-router)#passive-interface fastEthernet 0/1
EB2#conf t
EB2(config)#router eigrp 100
EB2(config-router)#network 192.168.1.252 0.0.0.3
EB2(config-router)#network 192.168.1.244 0.0.0.3
EB2(config-router)#network 192.168.1.0 0.0.0.63
EB2(config-router)#network 192.168.1.64 0.0.0.63
EB2(config-router)#no auto-summary
EB2(config-router)#passive-interface fastEthernet 0/0
EB2(config-router)#passive-interface fastEthernet 0/1
Step5::
a)
EastHQ#conf t
EastHQ(config)#interface serial0/0/1
EastHQ(config-if)#bandwidth 384
EB2#conf t
EB2(config)#interface serial0/0/0
EB2(config-if)#bandwidth 384
b)
EB2(config)#interface serial 0/0/0
EB2(config-if)#ip summary-address eigrp 100 192.168.1.0 255.255.255.128
EB2(config)#int serial 0/0/1
EB2(config-if)#ip summary-address eigrp 100 192.168.1.0 255.255.255.128
c)
EB1(config)#interface serial 0/0/0
EB1(config-if)#ip summary-address eigrp 100 192.168.0.0 255.255.255.0
EB1(config)#interface serial 0/0/1
EB1(config-if)#ip summary-address eigrp 100 192.168.0.0 255.255.255.0
Step6::
Enter NetAdmin:
ping>172.16.100.0
ping>172.16.100.126
ping>172.16.100.130
ping>172.16.100.194
ping>64.100.1.1
Another Answer:
· The router name is EB2.
Router(config)# hostname EB2
· The privileged EXEC mode uses the following encrypted password: class.
EB2(config)#enable secret class
Enable Telnet and console line logins and use the following password: cisco.
EB2(config)#line vty 0 4
EB2(config)#password class
EB2(config)#login
EB2(config)#exit
· Configure the banner message-of-the-day as Authorized access only!
EB2(config)#banner motd %Authorized access only!%
b. Using the Addressing Table, configure and activate all the necessary interfaces on E-Branch2.
c. Configure correct host IP addressing.
EB2#show ip interface brief
EB2#show ip route
Configure EPC2 with the last IP address in the subnet.
192.168.0.254 255.255.255.128
Default gateway 192.168.0.1
Configure EPC4 with the last IP address in the subnet.
192.168.1.126 255.255.255.192
Default gateway 192.168.1.1
Step 2: Discover the Network.
a. Explore the network to determine the IP address of the serial interface that EastHQ uses to connect to E-
Branch2.
b. Remotely access EastHQ.
EB2# show interfaces
EB2# show cdp neighbors
EB2# show ip route
EB2# telnet 192.168.1.253
EastHQ(config)#interface serial0/0/0
EastHQ (config-if)#ip address 192.168.1.249 255.255.255.252
EastHQ (config-if)#no shutdown
EastHQ (config-if)#exit
EastHQ (config)#interface serial0/0/1
EASTHQ(config-if)#ip address 192.168.1.253 255.255.255.252
EASTHQ(config-if)#no shutdown
EASTHQ(config-if)#exit
EASTHQ(config)#interface serial0/1/0
EASTHQ(config-if)#ip address 209.165.201.6 255.255.255.252
EASTHQ(config-if)#no shutdown
EASTHQ(config-if)#exit
EASTHQ(config)#interface serial0/1/1
EASTHQ(config-if)#ip address 192.0.2.2 255.255.255.252
EASTHQ(config-if)#no shutdown
EASTHQ(config-if)#exit
Step 3: Configure Static and Default Routing.
a. Configure connectivity to the West Region.
· Configure a static route on EastHQ to the entire West Region. The West Region uses the 172.16.100.0/24
address
space. Use the next-hop address argument.
EastHQ#show ip route
Configure a static route
EastHQ(config)#route ip 172.16.100.0 255.255.255.0 192.0.2.1
Configure a default route on EastHQ to send to the Internet all other traffic for destinations that are not found in the
EastHQ routing table. Use the exit interface argument.
EastHQ(config)#route ip 0.0.0.0 0.0.0.0 serial0/1/0
b. Verify static and default routing.
EastHQ#show ip route
EastHQ#ping
Step 4: Configure EIGRP Routing.
Configure EIGRP on EastHQ, E-Branch1, and E-Branch2.
a. Use AS number 100.
b. b.Do not advertise the network between EastHQ and the Internet.
c. Do not advertise the network between EastHQ and the West Region.
d. Advertise all other attached networks.
e. Disable automatic summarization.
f. Disable EIGRP updates out interfaces where there are no EIGRP neighbors available.
g. On EastHQ, enter the one command in the EIGRP routing process that will propagate the default and static
routes to E-Branch1 and E-Branch2.
EastHQ(config)#router eigrp 100
EastHQ(config-router)#network 192.168.1.248 0.0.0.3
EastHQ(config-router)#network 192.168.1.244 0.0.0.3
EastHQ(config-router)#no auto-summary
EastHQ(config-router)#ip default-network
EastHQ(config)#interface serial0/1/0
EastHQ(config-if)#no eigrp 100
EastHQ(config)#interface serial0/1/1
EastHQ(config-if)#no eigrp 100
—————————————–
EB1(config)#router eigrp 100
EB1(config-router)#network 192.168.1.0 0.0.0.3
EB1(config-router)#network 192.168.1.0 0.0.0.127`
EB1(config-router)#passive-interface fa0/0
EB1(config-router)#passive-interface fa0/1
EB1(config-router)#CTRL+Z
——————————————
EB2(config)#router eigrp 100
EB2(config-router)#network 192.168.1.0 0.0.0.3
EB2(config-router)#network 192.168.1.0 0.0.0.63
EB2(config-router)#passive-interface fa0/0
EB2(config-router)#passive-interface fa0/1
EB2(config-router)#CTRL+Z
Step 5: Modify the default EIGRP operation.
a. Configure the link between EastHQ and E-Branch2 so that the correct bandwidth of 384 k/s is used in EIGRP
calculations.
b. Configure E-Branch1 to advertise a summary route for the subnets 192.168.0.0/25 and 192.168.0.128/25 to
EastHQ and E-Branch2.
c. Configure E-Branch2 to advertise a summary route for the subnets 192.168.1.0/26 and 192.168.1.64/26 to
EastHQ and E-Branch1.
EastHQ(config)#interface s0/0/1
EastHQ(config-if)#bandwidth 384
EastHQ(config-if)#ip bandwidth-percent eigrp 100 100
EB2(config)#interface s0/0/0
EB2(config-if)#bandwidth 384
EB2(config-if)#ip bandwidth-percent eigrp 100 100
——————————
EB1(config)#router eigrp 100
EB1(router-config)#network 192.168.0.0 0.0.0.3
EB1(router-config)#end
EB2(config)#router eigrp 100
EB2(router-config)#network 192.168.1.0 0.0.0.63
EB2(router-config)#end
———————————-
OR
For EB1
———–
EB1(config)#Int s0/0/0
EB1(config-if)#IP Summery-address eigrp 100 192.168.0.0 255.255.255.0
EB1(config)#Int s0/0/1
EB1(config-if)#IP Summery-address eigrp 100 192.168.0.0 255.255.255.0
———–
For EB2
——-
EB2(config)#Int s0/0/0
EB1(config-if)#IP Summery-address eigrp 100 192.168.1.0 255.255.255.128
EB2(config)#Int s0/0/1
EB1(config-if)#IP Summery-address eigrp 100 192.168.1.0 255.255.255.128
Share this:
Twitter Facebook 21 More
BY ISTIAQUEDEVASTATION IN ROUTER CONFIGURATION ON 24/04/2013.
You May Like
1.
About these ads
Like
Be the f irst to like this.
Related
ERouting OSPF PT Practice SBA Basic Switching/Wireless PT
Practice SBA
CCNA Exploration-2: Routing
Protocols and Concepts (Version
4.0) –Question and Answer.
In "Router Configuration"
In "Switch Configuration"
In "Final Exam Sample"
← EIGRP CONFIGURATION TEST OSPF ROUTING CONFIGURATION →
Leave a Reply
Blog at WordPress.com. / The Academica Theme.
Enter your comment here...
