175LBS TOW-BEHIND SPIKE SPREADER CT2214

ORIGINAL MANUAL

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE

Cannon Tools Limited Address: 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.

- 2 -

EC DECLARATION OF CONFORMITY

We CANNON TOOLS LTD

20 Station road, Rowley Regis, West Midlands,B65 0JU.U.K.

Declare that the following machine complies with the appropriate basic

safety and health requirements of the EC Directive based on its design and

type, as brought into circulation by us.

In case of alteration of the machine, not agreed upon by us, this declaration

will lose its validity.

Product description: TOW-BEHIND SPIKE SPREADER

Model: CT2214

Applicable EC Directives:

EC Machinery Directive 2006/42/EC

Harmonized standards

EN ISO 12100

20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.

Mr. Gurcharan Tony Singh Sanghera

Managing Director

CANNON TOOLS LTD

2017-06-08

- 3 -

GENERAL WARNINGS READ and UNDERSTAND this manual completely before using 175lb Spike Aerator Spreader.

Operator must read and understand all safety and warning information, operating instructions, maintenance and storage instructions before operating this equipment. Failure to properly operate and maintain the aerator spreader could result in serious injury to the operator or bystanders. Operation Warnings Do not at any time carry passengers, sit or stand on the aerator spreader. Do not allow children to play on, stand upon or climb on the aerator spreader. Always inspect the equipment before using to assure it is in good working condition. Replace or repair damaged or worn parts immediately. Always check and tighten hardware and assembled parts before operation. Do not exceed equipment maximum hopper capacity of 175lb. Avoid large holes and ditches when operating the equipment. Be careful when operating the aerator spreader on steep grades (hill). Always operate at reduce speed in rough terrain, along creeks, ditches and on hillsides. Do not operate close to creeks, ditches and public highways. To avoid personal injury and/or equipment damage DO NOT EXCEED 5MPH. Always use caution when loading and unloading the hopper. Only tow with recommended vehicles (Lawn/Garden Tractors and ATVs). Always refer to the vehicle owner’s manual for proper towing. This equipment is not designed to be used with zero-turn mowers. Always secure and lock aerator spreader to the vehicle hitch before operating.

. Crush and Cut Hazards Always keep hands and feet clear from moving parts while operating the equipment. Always clear and keep work area clean when operating.

Always wear safety gear, eye protection, gloves and work boots when operating the aerator spreader.

.

WARNING

The warnings, cautions, and instructions outlined in this instruction manual cannot cover all possible conditions or situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product and must be supplied by the operator.

Assembly Is Required This product requires assembly before use. See “Assembly” section for instructions. Because of the weight and/or size of the equipment, it is recommended that another adult be present to assist with the assembly. INSPECT ALL COMPONENTS closely upon receipt to make sure no components are missing or damaged. .

- 4 -

Hazard Signal Word Definitions

ABOUT YOUR 175LB AERATOR SPREADER

This 175lb aerator spreader has a roughed steel construction and is designed to aerate and spread

fertilizer and other materials. The spikes will penetrate the ground up to 2.5” deep, allowing for

compact soil to be loosened. The aerator spreader promotes a health lawn by opening up the ground

to allow water, air and nutrients to reach your lawns root system. It is ideal for heavy-traffic areas

(playgrounds and sports fields) and burned out, drought-damaged lawns. The aerator spreader has

the All-In-One feature of being able to aerate and fertilize at the same time, saving you time. Never

exceed the hopper’s rated loaded capacity of 175lbs when operating the equipment.

Technical specifications on the 175lb aerator spreader are provided in the “Specifications” section of this manual.

This is the safety alert symbol. It is used to alert

you to potential personal injury hazards. Obey all

safety messages that follow this symbol to avoid

possible injury or death.

DANGER indicates an imminently hazardous

situation which, if not avoided, will result in death

or serious injury.

DANGER

WARNING indicates a potentially hazardous

situation which, if not avoided, could result in

death or serious injury.

WARNING

CAUTION indicates a potentially hazardous

situation which, if not avoided, may result in minor

or moderate injury.

CAUTION

CAUTION used without the safety alert symbol

indicates a potentially hazardous situation which,

if not avoided, may result in property damage.

CAUTION

- 5 -

Read this owner’s manual before operating the equipment. Familiarize yourself with the location and function of the controls and features. Save this manual for future reference.

1) Flows Control Lever – Controls the flow of material.

2) Poly Hopper – Do not exceed maximum load capacity 175lb.

3) Tires / Wheel – Do not exceed the recommended rate 25 PSI.

4) Aerator Spikes – Puts small holes in the ground.

5) Hitch – Pin-type design use only with approve vehicles.

6) Spike Control Handle – Lifts and lowers the aerator spikes.

.

Controls and Features Identification

2

3

4

5

6

1

- 6 -

CAUTION

Read and follow all instructions for assembly and operation. Failure to properly assemble this equipment could result in serious injury to the user or bystanders, or cause equipment damage.

AERATOR SPREADER COMPONENT PARTS AND ASSEMBLY

Take all parts out of the shipping crate and inspect components to ensure there are no missing pieces before starting to assemble the aerator spreader follow steps 1 through 8.

TOOLS REQUIRED

Rubber or Wooden Hammer

10, 13, 14, 22 & 24mm Wrenches

Adjustable Wrench

Pliers

Component and Hardware Parts

- 7 -

CAUTION

When assembling or using the aerator spreader exercise caution at all times, the spikes are sharp and may result in serious injury to the user or bystanders.

STEP 1: Attach Tow Bar Assembly to the Hopper

1. Remove the two M6 lock nuts in the bottom front of the hopper (Pic.1).

2. Put a M14 hex nut and Ø14 big washer to the support strut of the fluted disc assembly, then

attach the support strut to the card slot of the tow bar, and tighten with a Ø14 big washer and

M14 hex nut. (Pic.1).

3. Insert the original bolts through the holes on the beveled side of the tow bar assembly.

Secure using the M6 lock nuts (Pic.2).

STEP 2: Attach Handle Assembly to the Hopper

1. Remove one M6 lock nut from the front top of the hopper (Pic.3).

2. Insert the original bolt through the holes on the adjustable handle assembly. Loosely secure

using a M6 lock nut.

3. Insert one M6x16 hex bolt with an Ø6 big washer through the other hole at the top of the

hopper and the adjustable handle assembly.

4. Loosely tighten the parts together using the M6 lock nut (Pic.4).

Assembly Instructions

- 8 -

STEP 3: Assemble the Tow Bar and Adjustable Handle Together

1. Remove the M8x25 hex bolt and M8 lock nut on the tow bar assembly (Pic.5)

2. Insert the M8x25 hex bolt through the hole at the bottom of the adjustable handle assembly

and the tow bar assembly.

3. Secure together using a M8 lock nut (Pic.6).

4. Put the adjustable handle assembly in a suitable position and tighten all hardware in the prior

steps 2 and 3.

STEP 4: Attach Hitch Studs and Support

1. Remove the hitch studs at one of end of the hitch rod (Pic.7).

2. Insert the hitch rod through the hole at the bottom of the adjustable handle and screw on the

hitch studs (Pic.8).

3. Insert tow hitch studs at each end of the hitch rod and through hitch support hole (left and right)

at the bottom of the hopper. Secure using M6 lock nut (Pics.9&10).

NOTE: Hitch studs should not be screwed too tight, they need to be able to rotate freely.

- 9 -

STEP 5: Attach the Control Handle

1. Remove the M6 lock nut on the upper left of the hopper (Pic.11) 2. Insert the original bolts through the support rod, wheel assembly bracket and control handle

and loosely secure together using a M6 lock nut. 3. Insert the M6x16 hex bolt through the hole on the hitch plate and hole on the support rod and

loosely secure using a M6 lock nut.

4. Use a M8x20 hex bolt to attach the control handle and wheel assembly bracket together and

loosely tight with a M8 lock nut (Pics.11&12).

STEP 6: Attach & Adjust the Tow Bar and Support Rod

1. Insert two M6x16 hex bolts through the holes on the support rod and the tow bar and loosely

tighten using two M6 lock nuts (Pic.13&14).

2. Put in position the tow bar and support rod and tighten all hardware in steps 5 and 6.

- 10 -

STEP 7: Attach the Wheels

1. Attach the wheels on the wheel brackets and secure using M16 lock nuts (Pics15&16).

STEP 8: Final Adjustment and Assembly

1. Securely tighten all hardware in steps 1 through 7 before operating the spike aerator spreader.

- 11 -

WARNING

Before operating or using this equipment, review the instructions below and safety information. Failure to follow these instructions may result in property damage or injury to the operator or bystanders.

IMPORTANT:

Aerating is putting small holes in the soil up to 2.5 inches in length to create a small reservoir that will bring oxygen, fertilizer and water down to the roots. For best aerating results follow the soil/lawn preparation and operating aerator procedures.

SOIL AND LAWN PREPARATION

1. Remove large and small debris from work area. 2. If the ground is hard and dry, it is recommended the ground be sprinkled or watered for one or

two hours prior to aerating.

3. If the ground is wet or muddy DO NOT attempt to aerate or fertilize.

4. Mow lawn and remove loose clippings before aerating or fertilizing.

USING YOUR AERATOR SPREADER

1. DO NOT at any time carry passengers sit or stand on the aerator spreader. 2. Only tow with recommended vehicles (Lawn/Garden Tractors and ATVs). 3. Refer to the vehicle owner’s manual for proper safety and towing instructions. 4. Always secure and lock the aerator spreader to the vehicle hitch before operating. 5. Determine the approximate square footage of the area to be covered and estimate the amount

of fertilizer or seed required. REFER TO MATERIAL PACKAGING LABEL. 6. Move the aerator spreader to the area where application is to begin. 7. Loosen the plastic wing nut and move it to the desired setting. Retighten the nut. 8. Making sure the flow control lever is in the “OFF” position; fill the hopper, breaking up any

lumps. 9. Lower the aerator spikes to the operating position. 10. Start the spreader in motion and then move the flow control lever to the “ON” position as you

travel across your lawn. 11. Do not make sharp turns with spikes in the ground

12. On sloped lawns, always aerate in an up and down direction. DO NOT attempt to aerate

across the slope always go in an up and down direction.

13. Always use caution when backing the equipment to avoid “jack-knifing”. Always back up in a straight line.

14. Raise aerator spikes to transport position when crossing over concrete or other hard surfaces. 15. Do not aerate if the ground is extremely hard or dry. If ground is too dry, sprinkle or water for

one to two hours prior to use. 16. Do not aerate if the ground is too wet (muddy)

17. Vehicle braking and stability may be affected with the attachment of this equipment.

18. Never exceed 5mph when towing the aerator spreader.

19. DO NOT exceed load capacity of 175lbs.

CAUTION

Always move the flow control lever to the “Off” position to prevent excessive release of fertilizer when stopping, turning or filling the aerator spreader.

Operation Instructions

- 12 -

WARNING

Improper maintenance and storage of the aerator spreader may void your warranty.

MAINTENANCE Rinse/dry inside and outside of the aerator spreader after each use.

Before operating make sure the tires have the RECOMMENDED TIRE PRESSURE 25 PSI.

Regularly grease axle and wheel bearing area or when needed. Periodically check all fasteners for tightness.

Annually clean and lightly lubricate spike assembly and shaft or when needed. Use a glossy enamel spray paint to touch up scratched or worn painted metal surfaces.

Spikes periodically need to be sharpened with a small grinder to maintain good penetration.

Never exceed load capacity rating of 175lbs it will damage the equipment..

IMPORTANT:

If a part needs replacement, only use parts that meet the manufacturer’s specifications. Replacement

parts that do not meet specifications may result in a safety hazard or poor operations.

STORAGE Never allow material to be stored in the hopper for extended periods of time.

Before storing make sure the aerator spreader is clean and dry for years of trouble free service.

Lightly lubricate all metal surfaces and moving parts to prevent rust.

Store indoors or protected area during severe weather and winter months.

Maintenance and Storage

- 13 -

Hopper Capacity ........................................................................................... 175lb

Hopper Construction ....................................................................................... Poly

Frame Construction ........................................................................................ Steel

Working Width ................................................................................................... 40”

Number of Spikes Wheels .................................................................................. 12

Max. Aeration Depth ......................................................................................... 2.5”

Wheel Type ........................................................................................... Pneumatic

Wheel Size ........................................................................................................ 10”

Tire Pressure (PSI) ............................................................................................ 25

Hitch Type ................................................................................................ Pin Style

Unit Weight ................................................................................................ 58.37lb

Specifications

- 14 -

Parts Drawing & Parts List

- 15 -

PART# DESCRIPTION QTY PART# DESCRIPTION QTY

1 Cotter Pin Ø4x30 6 38 Support Rod 1

2 Flat Washer Ø20 6 39 Hex Bolt M6X35 1

3 Axle Spacer 2 40 Hex Bolt M6X45 1

4 Frame Left 1 41 Carriage Bolt M6X25 1

5 Hex Bolt M6X30 1 42 Teeth Washer Ø8 1

6 Short Bushing 2 43 Big Washer Ø6 19

7 Hex Bolt M5X10 16 44 Bushing 1

8 Scratch Board 4 45 Wing Nut M6 1

9 Middle Bushing 1 46 Nylon Washer 2

10 Handle Locking Plate 1 47 Adjustable Handle 1

11 Hex Bolt M6X16 22 48 Handle Grip 1

12 Mobile Door Assembly 1 49 Control Shelves 1

13 Hitch Studs 2 50 Support Shelves 1

14 Nylon Lock Nut M6 30 51 Gauge and Lever Assembly 1

15 Flat Washer Ø16 14 52 Flat Washer Ø8 1

16 Fluted Disc Spacer (Short) 2 53 Hex Bolt M6X20 2

17 Axle Spacer 16 54 Small Sprocket Axle Assembly 1

18 Fluted Disc & Bushing Assembly 4 55 Screw Bushing Ø22x18 1

19 Fluted Disc 8 56 Hex Bolt M5X35 2

20 Fluted Disc Spacer (Long) 6 57 Flat Washer Ø5 2

21 Spring 1 58 Bushing Chain Cover Spacer 2

22 Hitch Rod 1 59 Nylon Lock Nut M5 2

23 Hex Bolt M16X110 2 60 Bushing Chain Cover 1

24 Wheel Axle Hole Ø16 2 61 Bushing Chain 1

25 Hex Thin Nut M16 2 62 Big Sprocket Axle Assembly 1 26 Wheel Assembly Bracket 1 63 Big Sprocket Spacer 1 27 Hex Bolt M8X20 2 64 Frame Right 1 28 Nylon Lock Nut M8 3 65 Hex Bolt M6X25 1 29 Nylon Lock Nut M16 2 66 Small Middle Support 1 30 Operating Handle 1 67 Middle Support 1 31 Support Rod 2 68 Hopper 1 32 Handle Grip 1 69 Hex Bushing 2 33 Tow-Bar Assembly 1 70 Support Strut 1 34 Hitch Bracket 1 71 Hex Nut M14 2 35 R Pin Ø3x75 1 72 Composite Bearing 1 36 Pin 1 73 Big Washer Ø14 2 37 Hex Bolt M8X25 1

Parts Drawing & Parts List

- 16 -

CANNON TOOLS LTD

Add: 20 station road, Rowley Regis, west midlands,B65 0JU.U.K.

Made in China