2 OF 2 BILL OF QUANTITIES FOR THE CONSTRUCTION OF … · Indian Statstical Institute Alur Associates SL PARTICULARS FLR UNIT QNTY RATE AMOUNT 15 Providing and removing centering,

Indian Statstical Institute Alur Associates

ARCHITECTS & CONSULTANTS

M/s. Alur & AssociatesNo:3,14thMainRoad, Vasanthnagar,

Bangalore- 560 052.Ph:080-22356234

Fax No:080-41076707E-mail:[email protected]

ISSUED TO ________________________

(CIVIL, WATER SUPPLY, SANITARY & ELECTRICAL WORKS)

FOR

THE CONSTRUCTION OF RESEARCH SCHOLARS HOSTEL

2 OF 2

I N D I A N S T A T I S T I C A L I N S T I T U T E

8th MILE POST, MYSORE ROAD,BANGALORE

Tel : 080 28483002 - 28483006,Fax 080 22293517, E-mail : [email protected]

BILL OF QUANTITIES

FOR INDIAN STATISTICAL INSTITUTE

ATBANGALORE

Contractors Seal Signature 1


MANDATORY CONDITIONS

1

2

3

4

5

6

7

8

9

10

11

12

13

In Case of Rate Only Items / Non tendered items, a detailed rate analysis will have to be provided and approved by the Architect before execution.

43 Grade cement is to be used for all works until unless mentioned or specified.

One Model Room is to be completed in all respects including painting, flooring, bathroom fittings & fixtures, doors and windows, electrical fixtures and switch points etc., \ for approval from the works committee / architect before commencing the finishing works on the other rooms

Structural steel works are to be executed in Bangalore and delivered to the site. The fabricator has to be approved by the Architect / Structural Engineer.

Polishing to be included as a part of the rate for all teak wood / veneer items

Two coats of Enamel paint over one coat of Zinc oxide / primer and putty (metal paste) to be included as a part of rate for all wood works and metal works unless otherwise mentioned.

In all earth excavations, the excavated earth to be cleared at least 3m from all foundation pits until refilled. This should be included in rate quoted.

All finishing items / structural materials should be approved by the Architect / Engineer in charge before execution.

Clearing Constructional debris is responsibility of the Contractor (Will not be Measured and Paid Separately)

All the bar bending and Centering / Shuttering Works to be Completed as per dates, and No works will be carried out TWO days prior to the date of Concreting for Structural / Electrical Checking.

For all the major Concreting like Footings, Roof Slabs etc, the concreting Dates should be intimated at least 10 days in advance to the Architect / Engineer In charge.

Liasioning with BESCOM / Concerned department includes re submitting estimates and obtaining necessary approvals before commencing the work if required.

The Electrical Contractor is directly responsible with BESCOM department without involving the owner in any matter and has to introduce himself to BESCOM before commencement of any work.



TENDER BILL OF QUANTITIES FOR PROPOSED CONSTRUCTION OFRESEARCH SCHOLARS HOSTEL FOR INDIAN STATSTICAL INSTITUEBANGALORE CAMPUS.

areaGround Floor = 565.30 Sqm

First Floor = 544.25 SqmSecond Floor = 544.25 SqmTerrace Floor = 34.69 Sqm

TOTAL = 1688.49 Sqm

SL PARTICULARS FLR UNIT QNTY RATE AMOUNT

A CIVIL WORKSEXCAVATION WORKS

1 Earth work in surface excavation in Hard soil forleveling and lowering the ground manually (otherthan foundation of buildings, culverts, road drainsand trenches of pipe lines and cables) andremoving the excavated stuff to a distance notexceeding 50m and lift upto 1.5m, excavatedsurface levelled of clods and neatly dressed as perspecifications.

GF Cumt 112.00

2 Earth work excavation for foundation of buildings,culverts, water supply, sanitary lines and electricalconduits either in pits or in trenches 1.5m andabove in width, in Hard soil not exceeding 1.5m indepth including dressing the bottom and sides ofpits and trenches, stacking the excavated soil clearfrom edges of excavation with lead upto 50m. afterbreaking of clods complete as per specifications.

GF Cumt 951.00

3 Extra additional lift of 1.5m or part thereof forexecavation in loose/ soft or hard soil includingcost of materials,labour complete as perspecifications.

GF Cumt 15.00




4 Excavation 1.5m and above in width in soft rockwithout blasting for foundation of buildings,watersupply,sanitary lines and electrical conduits eitherpits or in trenches not exceeding 1.5m.indepth,stacking the excavated stuff from edges ofexcavation with lead upto 50m including cost ofexplosives,labour and HOM of equipment completeas per specifications.

GF Cumt 22.00

5 Extra additional lift of 1.5m or part thereof forexecavation in soft or hold rock including cost ofmaterials,labour complete as per specifications.

GF Cumt 15.00

6 Filling available excavated earth (excluding rock)in sides of foundations upto plinth in layers notexceeding 20cms in depth, compacting eachdeposited layer by ramming after watering withlead upto 50m and lift upto 1.5m including cost ofall labor complete as per specifications

GF Cumt 743.00

7 Earth work excavation (in deposited soil and fillingsides of foundation upto plinth in layers notexceeding 20cms. in depth, compacting eachdeposited layer by ramming after watering withlead upto 50m. and lift upto 1.5m.including cost oflabour complete as per specifications.

GF Cumt 79.00

8 Disposal of Excess Excavated material with inthe Site Premise all as directed including Loading,Unloading, Stacking, Spreading, leveling etc.complete all as directed by the Architect & Client .The Lead/Distance of site of disposal is as per thelocation earmarked for the same by Corporation &details of the same to be obtained & ascertainedwhile quoating the rate for the same.

GF Cumt 209.00

9 Disposal of Demolished debris outside the site premises as directed by the Architect / Institue including Loading, Unloading, etc. complete . The Lead/Distance of site of disposal is 10 kms from the site premises. . (90 cft per load)

GF Loads 5.00




10 Providing and injecting chemical emulsion for Pre-Constructional Anti-Termite Treatment, creatingcontinuous chemical barrier under and around thecolumn pits, walls, trenches, basement excavation,top surface of the plinth filling, junction of wall andfloor, along the external perimeter of building,expansion joints, over the top surface ofconsolidated earth on which apron is to be laid,surrounding of pipes and conduits, withchloropyriphos emulsifiable concentrates of 20% concentration, including cost of chemical,diluting in water to one percent concentration,labor, HOM of equipments, complete as perspecifiations. (Plinth area of the building at groundfloor only shall be measured)

GF Sqmt 594.00

PCC WORKS11 Providing and laying in position plain cement

concrete of mix 1:4:8 using 40mm and down sizegraded granite metal, machine mixed, concretelaid in layers not exceeding 15cms thick, wellcompacted, in foundation, floor bed , includingcost of all materials, labor, HOM of machinery,curing complete as per specifications.

GF Cumt 165.00




12 Providing and laying in position plain cementconcrete of mix 1:2:4 using 20mm and down sizegraded granite metal, machine mixed, concrete,laid in layers not exceeding 15cms, thick, wellcompacted, in foundation and plinth, including costof all materials, labor, HOM of machinery, curingcomplete as per specifications.

GF Cumt 6.00

(For Sill & coping) FF Cumt 6.00

SF Cumt 6.00

TF Cumt 3.00

13 Providing and laying in position plain cementconcrete of mix 1:3:6 using 20mm and down sizegraded granite metal, machine mixed, concrete,laid in layers not exceeding 15cms, thick, wellcompacted, in foundation and plinth, including costof all materials, labour, HOM of machionary, curingcomplete as per specifications.

GF Cumt 17.00

(Flagging or paving)

RCC WORKSNote: For all concrete works, cost for drip moulds of size 25mm x 50mm to be to be included in the quoted rate & is to be provided in slab, beams and where ever required.

14 Providing and laying cement concrete by pumpingusing 20 mm and down size granite jelly of readymixed concrete (RMC) for R.C.C works laid in15cms thick layers and well compacted vibrating,curing, finishing with necessary cement mortar,with all lead and lifts etc. complete (exclusive ofcost of steel and fabrication charges)

GF Cumt 197.00

Ready mixed Cement Concrete nominal mix1:1.5:3 (M-20) for raft foundation, column footing,main and secondary beams.

( For Footings )




15 Providing and removing centering, shuttering,strutting, propping etc and removal of form workfor foundations, footings, bases of columns formass concrete including cost of all materilas,labour complete as per specifications.

GF 315.00

( For Footings )

16 Providing and laying in position reinforced cementconcrete of mix 1:1.5:3 with 20mm and down sizegraded granite metal, machine mixed, concretelaid in layers not exceeding 15cms thick, vibratedfor R.C.C beams, columns of all sizes infoundation plinth and superstructure ground floorlevel for columns, including cost of all materials,labor, HOM of machinery, curing, complete as perspecifications.

(For Columns Plinth Beams, Lintels, S/C )

GF Cumt 95.00

FF Cumt 16.00

SF Cumt 16.00

TF Cumt 1.00

17 Providing and laying in position machine batched ,machine mixed and machine vibrated design mixConcrete confirming to IS :10262- 2009 ofspecified grade (unless otherwise specified), forreinforced concrete structural elements, as perrelevant IS specifications, using 20mm and downsize graded granite jelly for RCC works, includingadmixtures if any in recommended proporations toaccelerate, retard setting of concrete, improveworkability without impairing strength anddurability, laid in layers and well compacted,machine batched, machine mixed, vibrated, curing,including necessary steel/ plywood/ plank centring,shuttering, form works and scaffolding with all lead,lift at level as specified etc. complete as perdesign, drawing and direction of Architect / Client[excluding the cost of steel reinforcement andfabrication charges] for the following works.

GF Cumt 50.00

The Mix Design of various grades of concrete shallbe got done by the contractor at his cost fromreputed Institutions / Laboratories with approval ofthe Architect / Trust for further implementation inthe site.

FF Cumt 34.00




RCC Columns of M40 Grade SF Cumt 34.00

TF Cumt 3.00

18 Providing and laying in position reinforced cementconcrete of mix 1:1.5:3 with 20mm and down sizegraded granite metal, machine mixed, concretelaid in layers not exceeding 15cms thick, vibratedfor all works in foundation, plinth and ground floorlevel for roof slabs, S/c, lintels, retaining walls,return walls, walls of any thickness includingattached pilasters, columns, piers, abutments,pillars, posts, struts, buttress, string or lacingcourses, parapets, coping, bed blocks, anchorblocks, plain window cills, fillets etc, includingproviding and removing centering, shuttering,strutting, propping etc and removal of formworkcost of all materials, labor, HOM of machinery,curing, complete as per specifications. (excludingcost of steel, fabrication and plastering)

GF Cumt 28.00

(For Lift Walls) FF Cumt 18.00

SF Cumt 18.00

19 Providing and removing centering, shuttering,strutting, proppering etc, and removal of form workfor columns, pillars, piers, post and struts, circularor curved in plan including cost of materials, laborcomplete as per specification. ( For Columns )

GF Sqmt 504.00

FF Sqmt 323.00

SF Sqmt 323.00

TF Sqmt 52.00

20 Providing and removing centering, shuttering,strutting, propping etc and removal of form workfor sides and soffits of beams, beam hanuchings,cantilever, girders, bressumers and lintelsexceeding 1m in depth including cost of allmaterials, labor complete as per specifications. ( For Plinth Beams/ Beams/ Lintels ).

GF Sqmt 992.00

FF Sqmt 581.00

SF Sqmt 581.00




TF Sqmt 151.00

21 Providing and laying cement concrete by pumpingusing 20 mm and down size granite jelly of readymixed concrete (RMC) for R.C.C works laid in15cms thick layers and well compacted vibrating,curing, finishing with necessary cement mortar,with all lead and lifts etc. complete (exclusive ofcost of steel and fabrication charges)

GF Cumt 134.00

Ready mixed Cement Concrete for Beams,Columns, Stair case and Roof with nominal mix1:1.5:3 (M-20)

( For Beams and Slabs ) FF Cumt 120.00

SF Cumt 120.00

TF Cumt 21.00

22 Providing and removing centering, shuttering,strutting, propping etc and removal of form workfor flat surface such as suspended floors, roofs,landings, balconies and likes, thickness upto200mm including cost of all materials, laborcomplete as per specifications,

( For Roof Slab )

GF Sqmt 683.00

FF Sqmt 683.00

SF Sqmt 683.00

TF Sqmt 72.00

23 Providing and laying in position reinforced cementconcrete of mix 1:1.5:3 with 12mm and down sizegraded granite metal, machine mixed, wellcompacted for plain chajja of 7.5 cms. averagethickness upto ground floor level, including cost ofall materials, labor, HOM of machinery, curing,complete as per specifications. (For Chejja's)

GF Sqmt 281.00

FF Sqmt 281.00

SF Sqmt 281.00




24 Providing RCC loft (atta) 7.5 cms thick withcement concrete 1:1.5:3 using clean granite / trapjelly of 20mm and down size with necesssaryreinforcements at 20cms c/c as per designincluding form work, centering, curing, finishing theexposed faces with cement mortar (1:3) etccomplete(exclusive of cost of steel and fabricationcharges).

GF Sqmt 38.00

FF Sqmt 38.00

SF Sqmt 38.00

25 Providing and fixing RCC slabs 5cms thick, wallshelves with 12mm and down size jelly cementconcrete 1:1.5:3 including cm 1:3 plaster finishing,curing etc. Complete (excluding the steel andfabricating changes)

GF Sqmt 24.00

FF Sqmt 24.00

SF Sqmt 24.00

26 Providing and removing centering, shuttering,strutting, propping etc.for chajjas, corbelsetc.incuding edges including cost of all materials,labour complete as per specifcation. ( For Platforms, Chejja's and Loft,)

GF Sqmt 382.00

FF Sqmt 382.00

SF Sqmt 382.00

27 Providing and removing centering, shuttering,strutting, propping etc and removal of form workfor stairs(excluding landing) except spiral staircaseincluding cost of all materials, labor complete asper specification. ( For Staircase)

GF Sqmt 37.00

FF Sqmt 37.00

SF Sqmt 37.00

STONE WORKS




28 Providing and constructing granite / trap / basaltsize stone masonary in foundation cement mortar1:6, stone hammered dressed in courses not lessthan 20cms high, bond stones at two m.apart ineach course including cost of materials, labor,curing complete as per specifications.

GF Cumt 95.00

29 Providing and constructing granite / trap/ basaltsize stone masonry in basement with cementmortar 1:6, edges of stone chistle dressed incourses not less than 15cms high, bond stones attwo m.apart in each course including cost ofmaterials, labour, curing complete as perspecifications.

GF Cumt 63.00

30 Providing TMT steel reinforcement Fe 500 gradefor R.C.C work including straightening, cutting,bending, hooking, placing in position, lapping and/or welding wherever required, tying with bindingwire and anchoring to the adjoining memberswherever necessary complete as per design (therate should include - laps, hooks and wastage andno extra payment is permissible) cost of materials,labour, HOM of machinery complete as perspecifcations.

GF MT 37.00

FF MT 26.00

SF MT 26.00

TF MT 2.00

31 Providing and Fixing ArGeTon Facade tilescladding of 30mm thk and approved size by thearchitect / Institue using GI / Gypsteel / Aluminumbox Sections and counter sunk screws of SS forfixing the panels of approved colour & make bythe architect / engineer in charge including cost ofmaterials, scaffolding, labour, HOM of machinerycomplete as per specifcations

AF Sqmt 273.00




32 Providing, fabricating and fixing of stick typestructural glazing using Aluminum Extrusions of63.5mm x 58.00mm x 2.25 mm of 1.73 kgs /mtrfor vertical and Horizontal members and 63.5mm x38.1x1.33mm of 0.759 kg/Mtr, as outer frame withElectro Anodized Paint coated block finishing,using 6mm thick imported glass reflective hardcoated ocean blue raw glass with all necessaryaccessories like ultra glass Silicon sealant of space tape, Masking Tape, Galvanized Anchor bolt,machine screws, 6mm thick M.S. angle 50mmx150mm x6mm M.S.Galvanized L Brackets,structural sealant setting clocks, fasteners, wallconnection etc. complete

GF Sqmt 43.00

FF Sqmt 43.00

SF Sqmt 43.00

BLOCK MASONRY WORKS33 Providing and constructing Precast concrete solid

blocks with compressive strenght not less than 35Kg/Sqm with cement mortar 1:4 masonry (Quion,Jamb, Closer blocks) with solid concrete blocks ofsize 40 x 20 x 20 cms confirming to IS 2185 /1965 in super structure including cost of materials ,labour charges, scaffolding, curing complete as per specifications, including parapet wallls.

GF Sqmt 603.00

FF Sqmt 484.00

SF Sqmt 484.00

TF Sqmt 345.00

34 Providing and constructing non load bearing wallwith cement concrete solid blocks withcompressive strenght not less than 35 Kg/Sqmwith cement mortar 1:4 ( Jamb, Closer blocks)with blocks of size 40 x 10 x 20 cms confirming toIS 2185 / 1965 in super structure including cost ofmaterials , labour charges, scaffolding, curingcomplete as per specifications.

GF Sqmt 195.00

FF Sqmt 213.00

SF Sqmt 214.00




35 Providing and constructing non load bearing wallwith porotherm Horizontally perforated clay hollowblocks with compressive strength not less than 35Kg/Sqcm with cement mortar 1:4 ( Jamb, Closerblocks) with blocks of size 40 x 20 x 20 cmsincluding cost of materials , labour charges,scaffolding, curing at all heights, complete as perspecifications.

AF Sqmt 499.00




PLASTERING WORKS36 Providing 15mm thick cement plaster in single

coat with cement mortar 1:4 to brick masonryincluding rounding off corners wherever requiredsmooth Lime rendering, providing and removingscaffolding, including cost of materials, labor,curing complete as per specifications.( For Internal Walls )

GF Sqmt 1756.00

FF Sqmt 2139.00

SF Sqmt 2139.00

TF Sqmt 67.00

37 Providing 12mm thick cement plaster in singlecoat with cement mortar 1:3 to ceiling includingrounding off corners wherever required smoothLime rendering, : providing and removingscaffolding, including cost of materials, labor,curing complete as per specifications.

GF Sqmt 742.00

FF Sqmt 715.00

SF Sqmt 715.00

TF Sqmt 46.00

38 Providing 20 mm thick plaster in single coat withcement mortar 1:6, to brick masonry includingrounding off corners wherever required smoothrendering, providing and removing scaffolding,including cost of materials, labor, curing completeas per specifications, including parapet walls. ( For External Walls )

GF Sqmt 578.00

FF Sqmt 264.00

SF Sqmt 264.00

TF Sqmt 625.00




39 Providing rough cement plastering 15mm thick in single coat with cement mortar 1:6, to brickmasonry for base of dadoing with sand ofapproved quality, providing and removingscaffolding, including cost of materials, labor,curing complete as per specifications. ( Rough Plastering for External Cladding &Toilets)

GF Sqmt 301.00

FF Sqmt 301.00

SF Sqmt 301.00

TF Sqmt 63.00

40 Providing 20 mm thick Exposed Concrete FinishPlastering using Wooden planks / Sheets(MS/Wood) of approved Size by the architect /Engineer in Charge in single coat with cementmortar 1:6, to brick masonry / rough plasterdsurface including rounding off corners whereverrequired smooth rendering, providing andremoving scaffolding, including cost of materials,labor, curing complete as per specifications,including parapet walls. ( For External Walls )

GF Sqmt 67.00

FF Sqmt 66.00

SF Sqmt 66.00

TF Sqmt 63.00

41 Extra for providing and mixing waterproofingcompound in cement plaster work at one kg perbag or in the proportion recommended by themanufacturers, for cement mortar 1:4, 12mm thickcost of materials complete as per specifications. ( For Toilets,sump )

AF Sqmt 510.00

42 Providing and making Plastering Grooves of12mm with 1:3 finishing as directed etc, complete

AF Rmt 450.00




43 Providing floating coat of cement to plasteringand finishing smooth, including cost of materials,labor, curing complete as per specifications

GF Sqmt 183.00

44 Providing and making Plastering Bands of 100 mmin ht with 12mm thickness in 1:3 finishing asdirected etc, complete

AF Rmt 450.00

45 Providing and making Plastering Bands of 200 mmin ht with 12mm thickness in 1:3 finishing asdirected etc, complete

AF Rmt 450.00

FLOORING, SKIRTING & DADOING

46 Providing and fixing Vitrified tiles 60cms x60cms of approved make shade, size andminimum thickness of 10mm approved by theArchitect / Institue and as per techinicalspecifications given by the manufacturer forflooring laid on a bed of 20mm thk cement mortar1:3 mix, flush pointing with white cement usingcolor pigment, including cost of materials, labor,curing, complete as per specifications

GF Sqmt 286.00

Basic Rate of Tile Rs. 750/ SqmtFF Sqmt 286.00

SF Sqmt 286.00

47 Providing and fixing 20mm thick Sadarahalli Prepolished granite of approved colour and quality inCM 1:4 of 20mm thick including full round bullnosing as per details, oxide finish etc., in all floorsas per specifications, . complete

AF Sqmt 444.00

(For Corridors)




48 Providing and fixing 20mm thick polished graniteof approved colour and quality in CM 1:4 of 20mmthick as per details, oxide finish etc., in all floorslaid to line and level and jointed with cement slurrymixed with pigmnet to match the shade of the slab,including making Groove for 3 lines, cost ofmaterials, labour, curing, including half roundbull nosing, complete as per specifications.

AF Sqmt 68.00

(for S/C Treads & Risers )

49 Providing and fixing 10mm thick polished StripedFlamed granite of 0.15 width, approved colourand quality in CM 1:4 of 20mm thick includingcutting, smoothining the edges, fixing the granite atevery 12mm gap and filling the gap with sunkpointing in CM 1:3 as per details etc., in all floorsas per specifications, . complete

AF Sqmt 217.00

(For Balconies)

50 Providing and fixing 20mm thick Pre polishedblack Galaxy granite of approved colour andquality in CM 1:4 of 20mm thick including halfround bull nosing as per details, oxide finish etc., inall floors as per specifications, . complete

AF Sqmt 14.00

(For Entrance Steps)

51 Providing and fixing 20mm thick Pre polishedblack Galaxy granite of approved colour andquality for counters including half round bull nosingas per details, oxide finish, making holes etc., in allfloors as per specifications, . complete

AF Sqmt 54.00

(For Counters)

52 Providing Ceramic tiles of approved make, shadeand size and 8mm minimum thickness and asper techinical specifications given by themanufacturer for flooring, laid on a bed of 20mmthick, cement mortar 1:3 mix, flush pointing withwhite cement using color pigment, including cost ofMaterials, labor, curing, complete as perspecifications.

GF Sqmt 58.00

Basic Rate of Tile Rs. 500/ Sqmt FF Sqmt 58.00

SF Sqmt 58.00




53 Providing skirting, dado, rises of steps with colorglazed tiles 6mm thick and as per techinicalspecifications given by the manufacturer on 12mmthick cement plaster 1:3 and joined with whitecement slurry over rough plaster surface(excluding cost of rough plastered surface whichshould be measured and paid separately) usingglazed tiles of approved make and size includingcost of materials, labor, complete as perspecifcations.

GF Sqmt 235.00

Basic Rate of Tile Rs. 550/ Sqmt FF Sqmt 235.00

SF Sqmt 235.00

PAINTING WORKS54 Providing and applyig two coats with Acrylic

Emulsion painting of approved brand and shadeon wall surface including priming caot withdistember primer after throughly brooming thesurface free from mortar drops and other foreignmatter including preparing the surface even andsand paper smooth,cost of materials,labour,complete as per specifications(For Walls)

AF Sqmt 6100.00

55 Providing and applyig two coats with oil boundwashable distemper of approved brand andshade for ceiling including priming caot withdistember primer after throughly brooming thesurface free from mortar drops and other foreignmatter including preparing the surface even andsand paper smooth,cost of materials,labour,complete as per specifications(For Ceiling)

AF Sqmt 2217.00

56 Providing and painting two coats of External Emulsion paint of approved make, quality, colorand shade over one coat of Snowcem primerincluding providing and removing necessaryscaffolding and cleaning the paint stains wherevernecessary etc., complete including the cost of allmaterials, cost of labor for all items or works.

AF Sqmt 1730.00




57 Providing and applying painting two coats over acoat of primer, on new wood surface and / or woodbased surface with enamel paint to give an evenshade, cleaning the surface of all dirt, dust andforeign matter, sand papering including cost ofmaterials, labor, complete as per specification.

AF Sqmt 570.00

DOORS

58 Providing and Fixing Sal wood frames of doors,windows, clerestory windows, ventilators and otherframes,wrought,framed or assembled includingmaking plaster groves (excluding cost of cementconcrete and side clamps) but including cost ofmaterials, labor, HOM of machineries complete asper specifications.

AF Cum 7.00

59 Fixing of door frame in an existing openingincluding embedding frame in floor and walls aftercutting masonry for holdfasts for embeddingholdfasts in cement masonry in CC 1:3:6 of 20mmand downsize granite metal, painting two coats ofcoal tar to sides of frame, making good thedamages to walls and floor as required anddisposal of debris with lead upto 50 mts. includingcost of materials, labor charges, complete as perspecifications

AF Nos 41.00

60 Providing and fixing factory made single leaft rigidGRP Sandwich composite door shutter of32mm thick, laminated with two GRP skins withwood finish, fabricated using U. V - stabilizedIsopthalic Gelcoat and on layer of 450 gsm E-Glass Chopped strand Mat (CSM), impregnatedwith orthopthalic polyster resin. The thickness ofthe skins shall not be less than 1.5mm. ExpandedPolystyrene (EPS) structural foam panel of 29mmthickness and a density of 20 Kg/m3 shall be usedas core material. Wooden reinforcements made ofSeasoned Salwood block of cross section not lessthan 28mmx32mm and also necessary salwoodreinforcements for fixing the metal fittings such astower bolts, aldrops, handles etc, shall beprovided.

AF Sqmt 91.00




A structural adhesive compatible with EPS foamshall be used for bonding the core material, thesalwood reinforcement and the skins. The materialand process for manufacturing the door shuttersshall confirm to RV/TIFAC Composites DesignCentre Standards and specifications and the doorshutters tested in confirmation to IS 4020-1994.The finish of shutters will be plain colourWhite/Ivory/Beige/Light Grey or any other colourusing high quality pigments. Inclusing cost offixtures and inclusive of supply of shutters torespective work spot etc. complete as perdirections of engineers.

(For Toilets)

61 Providing and fixing 35mm thick companymanufactured imported flax board core shuttersto the existing frame using (HDF) High densityfiberboard skins scratch and skuff resistantmultipanelled as per deisgn and drawings includingd-line stainless steel fittings such as tower bolts,stays, handles, cylinderical locks etc complete withall lead and lift. (including polishing)

AF Sqmt 72.00

62 Providing and fixing in position fully pannelled GumSal wood shutters for doors, styles andrails of 30mm. Thick with bottom and lock rails180mm wide top rail and styles 100mm wide , asper drawing and pannels of 25mm thick includingproviding and fixing 4mm modi / approved makeglass in the sides of the shutters as side lights,cost of materials, labour, HOM of machineriescomplete as per specifications. (Including costfor providing and fixing of fixtures)

GF Sqmt 12.00




63 Providing and fixing Factory made Partly / Fullyglazed UPVC French Doors Horizontal Slidingsystem and the profile to be hollow, multichambered and steel reinforced with an outer wallthickness of 2mm. The basic construction shouldbe similar to that of Casement system. The slidersto be designed as ride over type system and toincorporate tracks using track spaces andinterlocks to be provided on all sashes to stop theingress of dust and external elements, the windowsystem to be internally glazed with single glasing of5mm thickness.All hardwares including its fittings are to be fixedthrough the reinforcement, all screws shouldpenetrate the reinforcement by atleast 2mm. Thesystem has to have adjustable rollers for fineradjustment and smooth functioning of the sliders.The system shoulfd be of Pristine colour withSquare bead and to be fixed as per design anddrawings in accordance with manufacturingspeciations, including cost of all materials, labor,HOM of machinery complete as per specifcations.

AF Sqmt 80.00

(French Doors)

64 Providing and fixing Factory made UPVC BalconyDoors of Casement system and the profile to behollow, multi chambered and steel reinforced withan outer wall thickness of 2mm. The basicconstruction should be similar to that of Casementsystem. The sliders to be designed as ride overtype system and to incorporate tracks using trackspaces and interlocks to be provided on all sashesto stop the ingress of dust and external elements,the window system to be internally glazed withsingle glasing of 5mm thickness.All hardwares including its fittings are to be fixedthrough the reinforcement, all screws shouldpenetrate the reinforcement by atleast 2mm. Thesystem has to have adjustable rollers for fineradjustment and smooth functioning of the sliders.The system shoulfd be of Pristine colour withSquare bead and to be fixed as per design anddrawings in accordance with manufacturingspeciations, including cost of all materials, labor,HOM of machinery complete as per specifcations.

AF Sqmt 54.00

(For Balconies)




WINDOWS & VENTILATORS

65 Providing and fixing in position Powder coatedaluminium windows and ventilators as perapproved drawings with sliding shutters usingdouble track window frame section of size61.85x31.75mm with 1.2mm thick, bottom sectionweight 0.695 kg/m, sides and top sections 1.3mm,thick weight 0.659 kg/m; and shutter comprisingtop and bottom section of size 40mmx18mm,1.25mm thick 0.417kg./m;shutter outer side40mmx18mm, 1.25mm, thick weight 0.417kg/m,shutter interlock section 40mmx26.7, 1.1mm thick,weight 0.469 kg/m, the shutters mounted on nylonrollers with approved quality of fixtures such asaluminium handles tower bolts etc,

AF Sqmt 32.00

and providing and fixing 5.5 mm thick plain/Tinted glass (Pin headed glass for Ventilators)for shutters fitter with rubber beading aluminiumsections anodized 12 to 15 microns, includingcutting to required length, joints mitred subdividingthe frame tenonned and rivetted in the assembledframe stiffened with end clips at corners anglesetc., and fixed to the walls, lintels, floor beams/cillsas the case may be with necessary steel, raulplugs, or teak wood gatties including cuttingmasonry or concrete and making good the originalsurface using cement mortar, aluminium sectionspretreated for removal of any other sticky materials( the coating should be cleaned after installation)including applying silicon sealent for the gaps, costof all materials, fixtures, labour and HOM ofmachinery complete as per specifications.




66 Providing and fixing Factory made Partly / Fullyglazed UPVC windows of Casement system andthe profile to be hollow, multi chambered and steelreinforced with an outer wall thickness of 2mm.The basic construction should be similar to that ofCasement system. The sliders to be designed asrideover type system and to incorporate tracksusing track spaces and interlocks to be providedon all sashes to stop the ingress of dust andexternal elements, the window system to beinternally glazed with single glasing of 5mm thickness.All hardwares including its fittings are to be fixedthrough the reinforcement, all screws shouldpenetrate the reinforcement by atleast 2mm. Thesystem has to have adjustable rollers for fineradjustment and smooth functioning of the sliders.The system shoulfd be of Pristine colour withSquare bead and to be fixed as per design anddrawings in accordance with manufacturingspeciations, including cost of all materials, labor,HOM of machinery complete as per specifcations.

AF Sqmt 141.00

67 Providing and fixing Stainless steel MosquitoMesh with magnetic catchers and to be fixedfor existing including cost of materials, fixtures,labour and HOM machinery complete as perspecifications.

AF Sqm 173.00

68 Providing and fixing M.S. Grill work for windowsand ventilators wieghing 21kgs per sqm using M.S.flats 25x5mm and M.S. square rods10x10mm, or combination of M.S flats and squarerods as per approved design and drawing includingcutting steel sections and welding the same torequired pattern with a coat red lead primer,twocoats of enamel painting of approved colour,cost ofmaterials,Fixtures,labour and HOM machinerycomplete as per specifications

AF Kgs 3245.00




69 Providing and fixing Grade 304 Stainless SteelRailing upto 0.9m height with 50mm dia pipe asHand rail, 50mm x 50mm box sections asBalustrades at every 0.9m spacing, Blasturade isto be based on ELEN Key bolt fitting system and 10mm dia strings to be fixed horizontally betweenthe balustrades at 150mm interval space betweenthe strings, fixing to done using SS plates andanchor bolts as per design and drawing includingcost of materials, fabrication charges, labour,making holes for fixing strings etc complete.

AF Rmt 37.00

(For Stair Case)

70 Providing and fixing Grade 304 Stainless SteelRailing upto 0.9m height with 50mm dia pipe asHand rail, 50mm x 50mm box sections asBalustrades at every 0.9m spacing, Blasturade isto be based on ELEN Key bolt fitting system and 10mm dia strings to be fixed horizontally betweenthe balustrades at 150mm interval space betweenthe strings, fixing to done using SS plates andanchor bolts as per design and drawing includingcost of materials, fabrication charges, labour,making holes for fixing strings etc complete.

AF Rmt 76.00

(For Balconies)

71 Providing and fixing in position collapsible steelshutters with single or double leaf with verticalchannel 20mmx10mmx2mm braced with flat irondiagonals 20mmx5mm size, with top and bottomrails of T iron sections of 40x40x6mm with 38mmdia steel pulleys complete with bolt and nuts,locking arrangements, stoppers, handles on bothsides with 7.5cms openings at 10cms c to capplying a priming coat of red lead paint. cost of allmaterials, labor, HOM of machinery complete asper specifcations.

AF Sqmt 80.00

72 Providing and Fixing MS Safety Door using 50mm x 50mm x 5mm MS L-angles as outerframe, 12mm x 12mm brite rods as grills includingTwo Coats of Enamel painting over one coat of redoxide primer , Locks, Tower bolts, fixing to thewalls in 1:2:4, curing etc complete.

AF Sqmt 40.00

WATERPROOFING




73 Providing and laying integral cement basedwaterproofing treatment including preparation ofsurface as required for treatment of roofs,balconies, terraces etc consisting of followingapplication(a) Applying and grouting a slurry coat of neatcement using 2.75kg/sqm of cement admixed withproprietary water proofing compund conforming toIS:2645 over the RCC slab after cleaning thesurface before treatment.(b) Laying cement concrete using bricks of size110X230X75mm with 50 % of cement mortar 1:5admixed with proprietary water proofing compundconforming IS:2645 over 20mm thick layer ofcement mortar 1:5 admixed with proprietary waterproofing compound to required slope and treatingsimilarly the adjoining walls up to 300mm heightincluding rounding off junctions of walls and slabs.(c) After two days of proper curing, applying asecond coat of cement slurry admixed withproprietary water proofing compound

AF Sqmt 609.00

(d) Finishing the surface with 20mm thick joint lesscement mortar of mix 1:4 admixed with proprietarywater proofing compound and finally finishing thesurface with trowel and neat cement slurry andmaking of 300x300mm square. (e) The whole terrace so finished shall be floodedwith water for a minimum period of two weeks forcuring and for final test including cost of materials,labour complete as per specifications

74 Providing and laying cinder concrete in cement1:15 (1cement: 15 cinder of 12.5mm nominalgauge) on terrace roof of sunken slabs, laid toslope, compacting, including cost of materials,labor, curing complete as per specifications.

AF Cumt 80.00




75 Providing and fixing on wall surface 4 kg/sq.cmPVC rain down water pipes 110 mm outer diaapproved make and brand with necessary specialslike shoes, bends and offsets fixed with pvcclamps, wall plugs, screws, including cost ofmaterials, labour etc complete as perspecifications.

AF Rmt 315.00

( Market Rate )

76 Providing and fixing Gypsum board false ceilingin Gl frame in 24 to 26 guage with main framebottom to bottom distance at 3'0" with cross pattiesat 18" centers with 24 to 26 guage Angle cleatssize 1"x1" suported at 2'6" centre to centre with12mm gypsum ceiling board with sheet metalscrews complete with one coat of top coat paint.the rate shall be inclusive of small moulding,cutouts for lights and AC grills and also TWframing, if any for AC grills, all wooden members of the ceiling shall be treated with antitermitetreatment. The ceiling shall be in perfect level andsmooth in finish and as per design and drawingsetc, complete.

AF Sqmt 76.00

77 Providing and fixing open type cabinets using12mm thick waterproof ply of approved make forshutters and frame with 1.5mm approved colouredlaminate including 3" SS handles, 3" SStowerbolts, 3" SS hinges, ball catchers etc with twocoats of enamel painting over one coat of primerand putty for inner surface complete.

AF Sqmt 31.00

A Total For Civil Works




B WATER SUPPLY & SANITARY WORKS

1 Earth work excavation for water supply andsanitary lines either in pits or in trenches 1.5m andbelow in width , in Hard soil not exceeding 1.5m indepth including dressing the bottom and sides ofpits and trenches, stacking the excavated soil clearfrom edges of excavation with lead upto 50m.afterbreaking of clogs complete as per specifications.

Cum 211.00

2 Refilling of available earth around pipelines,cables in layers not exceeding 20cms in depth,compacting each deposited layer by ramming afterwatering with lead upto 50m and lift upto 1.5 mtsincluding cost of all labor complete as perspecifications .

Cum 189.00

3 Providing and fixing 110mm dia PVC pipe ofapproved make with bends, Tee and joints withsolvent including scaffolding etc, complete(excluding the cost of specials) as per directions.

Rmt 368.00

4 Providing and fixing 160mm dia PVC SWR pipe ofapproved make with bends, Tee and joints withsolvent including scaffolding etc, complete(excluding the cost of specials) as per directions.

Rmt 158.00

5 Providing and fixing 75mm dia PVC SWR pipe ofapproved make with bends, Tee and joints withsolvent including scaffolding etc, complete(excluding the cost of specials) as per directions.

Rmt 263.00




6 Constructing brick masonry inspection chamber450 x 450mm, and 450mm depth, (clear insidedimension) for single pipeline, using table moldednon-modular bricks of class designation 50 incement mortar 1:5, C.I cover with frame (light duty)455x610mm internal dimensions, total weight ofcover with frame to be not less than 38 kg (weightof cover 23kg and weight of frame 15 kg ) R.C.C.top slab with cement concrete 1:2:4 mix 20mm anddownsize granite metal, foundation concrete 1:5:10with 40mm and downsize granite metal insideplastering 12mm thick with cement mortar 1:3,finish smooth with a floating coat of cement onwalls and bed concrete complete as per standarddesign including cost of materials, labor charges,curing complete as per specifications.

Nos 7.00

7 .-do- 600x600mm, and 450mm depth, (clear insidedimension) for single pipeline, using table moldednon-modular bricks of class designation 50 incement mortar 1:5, C.I cover with frame (light duty)600x600mm

Nos 17.00

8 .-do- 230x150mm and 450mm depth (clear insidedimension) for single pipeline, using table moldednon-modular bricks of class designation 50 incement mortar 1:5, C.I cover with frame (light duty)230x150mm

Nos 11.00




9 Constructing brick masonry circular type manhole 1.22 m internal dia at bottom 1.68m deep and0.56m dia at top, with table moulded and non-modular bricks of class designation 50 in cementmortar 1:4 inside cement plaster 12mm thick withcement mortar 1:3, finished with a floating coat ofneat cement, foundation concrete 1:3:6 mixedusing 40mm and down size granite metal andmaking necessary channel in cement concrete1:2:4 mix with 20mm and down size granite metal,finished with a floating coat of neat cement, withS.F.R.C. cover and frame (heavy duty, HD-20grade designation) 560mm internal diameterconfirming to IS :12592, total weight length ofcover and frame to be not less than 182 kg, fixedin cement concrete 1:2:4 20mm and down sizebroken granite metal, providing and removingcentering, shuttering including cost of materials,labour charges, HOM of mechineries complete asper specifications. (Excavation, footrests and12mm thick cement plaster on the external surfaceh ll b id t l )

Nos 4.00

10 Same as Item 9 but 1.22m internal dia, at bottom 2.29m deep

Nos 3.00

11 Providing 20mm square M.S footrest and fixing inmanhole with 1:3:6 cement concrete block of20x20x10cms using 20mm and down size metal ofsize including cost of materials, labor charges,curing complete as per specifications.

Nos 32.00

12 Providing 12mm thick cement plaster in singlecoat with cement mortar 1:6 to brick masonryincluding rounding off corners wherever requiredsmooth rendering , providing and removingscaffolding, including cost of materials, labor,curing complete as per specifications ( ForManholes)

Sqm 79.00

13 Providing stoneware gully trap of approvedquality and make fixing in CC 1:2:4 and plasteringwith CM 1:3 wherever necessary (Rate includescost of all materials, fixtures and lead) for 15 cms x10 cms

Nos 11.00

14 Providing and fixing 110 X 75 mm dia PVC SWRreducer socket

Each 79.00




15 Providing and fixing PVC SWR Vent Cowl 110mm including fixing with solvent complete.

Each 27.00

16 Providing and fixing 110mm dia PVC SWR plainbend.

Each 126.00

17 Providing and fixing 75mm dia PVC SWR plainbend.

Each 126.00

18 Providing and fixing 110mm dia PVC SWR doorTee.

Each 21.00

19 Providing and fixing 75mm dia PVC SWR doorTee.

Each 21.00

20 Providing and fixing 110mm dia PVC SWR plainTee.

Each 21.00

21 Providing and fixing 75mm dia PVC SWR plainTee.

Each 21.00

22 Providing and fixing PVC 75mm size Nahani Trapof approved make (Supreme) conforming to ISISpecifications and construction of Cistern in CC1:2:4 as per directions (Rate is inclusive of cost ofmaterials and fixtures and conveyance of materialsto work spot)

Nos 79.00

23 Providing and fixing Wall Mounted vitreous chinaclay, water closet European type with solidplastic seat and lid, C.P brass hinges, rubberbuffers. 10 liter low level, P.V.C flushing cistern (allare approved make) with fittings, C.I /M.Sbrackets, 40mm diameter flush bend with fittingsand clamps, overflow arrangements with specialand 25mm mosquito proof coupling of approveddesign, painting of fittings and brackets, cuttingand making good the wall and floor whereverrequired, including cost of materials, laborcomplete as per specifications

Nos 36.00

Hind Ware Cistern - Hindustan Sleek

24 Providing, fixing and testing white vitreous chinaclay oval shaped wash basin of size 560x 410mmwith CP waste coupling, waste connection pipeincluding cost of all materials, labor complete asper specifications.

Nos 36.00

Hind Ware - CAT NO 10017




Wash basin Oval 56*41+

25 Providing and fixing 110mm dia PVC door 45degree bends.

Nos 38.00

26 Providing and fixing white vitreous china clay,water closet Orissa pattern of size 580 x 440mmwith integral type footrests, 100mm S or P trap, 10liter low level, P.V.C flushing cistern (all areapproved make) with fittings, C.I / M.S brackets,32mm diameter flush pipe fittings and clamps,overflow arrangements with special and 25mmmosquito proof coupling of approved design,painting of fittings and brackets, cutting andmaking good the wall and floor wherever required,including cost of materials, labor complete as perspecifications

Nos 2.00

Hind Ware - CAT NO 20004 53*41 +Cistern - 21001

27 Supplying, fixing and testing of approved makeshower unit consisting of CP wall mixer withtelephonic shower arrangement only but withoutTelephone shower Crutch with provision for overhead shower with 115mm long bend pipe & wallflange including shower arm 190mm long castledwith wall flange with shower head having revolvingjoint etc complete.

Nos 1.00

Wall Mixer - Jaguar Continental - CAT NO 217Wall Bend - Jaguar Continental - CAT NO 273Shower - Jaguar Continental - CAT NO 493Shower Arm -Jaguar Continental -CAT NO 477

28 Supply, fixing and testing of approved makeHealth faucet fixed to15mm dial CP angle stopcock with wall flange with 1 mtr pipe and wall hooketc complete.

Nos 36.00

Jaguar Continental - CAT NO 563

29 Providing and fixing in position CP Angular stop cock of approved quality 32mm nominal boreincluding cost of all materials, labor and HOM ofequipments with all leads complete

Nos 108.00





30 Providing and fixing in position CP bib cock ofapproved quality 15mm nominal bore includingcost of all materials, labor, and HOM ofequipments with all leads complete as perspecifications.

Nos 36.00


31 Providing and fixing in position CP Pillar cock ofapproved quality 15mm nominal bore includingcost of all materials, labor and HOM of equipmentswith all leads complete as per specifications.

Nos 38.00


32 Providing and fixing C.P. brass towel rail 740mmlength, 20mm dia with c.p brackets, fixed towooden cleats with c.p. brass screws includingcost of materials, labor complete as perspecifications.

Unit 36.00

33 Supplying and fixing CP brass twin Robe hook fixed to wall / door with CP brass screws etc complete.

Nos 36.00


34 Supplying and fixing Recessed Type White soap dish ITALIA of approved shape and size fixed intowall with CM 1:3 etc complete.

Nos 36.00

Hindustan - CAT NO 40052

35 Providing and fixing 7.5 cms x 15 cms dia NP grating 100mm dia

Each 75.00

36 Providing and fixing 600x450mm dia rectangularshape mirror with plastic molded frame ofapproved make and shade with 6mm thick hardboard backing including cost of materials, laborcomplete as per specifications

Nos 36.00




37 Providing and fixing to wall, ceiling and floorgalvanized / mild steel tube 15mm dia nominalbore excluding cost of fittings, (medium gradeweight 1.27 kg/mtr) B class including cost of allmaterials, labor charges, HOM of equipments andtesting complete as per specifications.

Rmt 27.00

38 Same as Item 37 but to wall, ceiling and floorgalvanized / mild steel tube 20mm dia nominalbore excluding cost of fittings (medium gradeweight 1.65 kg/mtr)

Rmt 683.00

39 Same as Item 37 but to to wall, ceiling and floorgalvanized / mild steel tube 25mm dia nominalbore excluding cost of fittings (medium gradeweight 2.51 kg/mtr)

Rmt 315.00

40 Same as Item 37 but to wall, ceiling and floorgalvanized / mild steel tube 40mm dia nominalbore excluding cost of fittings (medium gradeweight 3.72 kg/mtr)

Rmt 158.00

41 Extra for concealed pipe including painting withanti corrosive bitumastic paint cutting chases,making good the concrete surface, and plaster for15mm dia nominal bore including cost of allmaterials, labor charges, HOM equipmentcomplete as per specifications.

Rmt 630.00

42 Same as item 41 but for 20mm dia Rmt 630.00

43 Providing and fixing in trenches galvanized / mildsteel tubes (medium grade) 25mm dia nominalbore with all fittings (earthwork in trenches to bemeasured and paid separately) including cost of allmaterials, labor charges, HOM of equipments andtesting complete as per specifications.

Rmt 132.00




44 Supplying and insulating hot water lines withAsbestos insulation rope etc., complete as perdirections of the engineer.

Rmt 210.00

45 Providing and fixing in position brass ball valvehigh or low pressure with plastic float of approvedquality 25mm nominal bore including cost of allmaterials, labor charges, HOM equipment with allleads complete as per specifications.

Each 2.00

46 Providing and fixing unplasticisied PVC connection pipe with brass union 15mm nominalbore 450mm length of PVC connection includingcost of all materials labor charges, HOMequipment with all leads complete as perspecifications.

Set 11.00

47 Providing and fixing in position brass gate valvewith CI wheel of approved quality (screwed end)20mm nominal bore including cost of all materials,labor charges, HOM equipment with all leadscomplete as per specifications.

Nos 38.00

48 Same as Item 47 but for 25 mm Nos 38.00

49 Same as Item 47 but for 40 mm Nos 7.00

50 Providing and Fixing GI union of approved make confirming to ISI specification "R " Brand.

40mm dia Each 13.00

25mm dia Each 76.00

20mm dia Each 76.00

51 Making Wall bores in Stone Masonry upto .45m width for soil / water pipe including necessary scaffolding etc complete

Nos 26.00

52 Making Wall bores in Brick Masonry upto .45m width for soil / water pipe including necessary scaffolding etc complete

Nos 89.00




53 Making Wall bores in Cement Concrete upto0.45m width for soil / water pipe includingnecessary scaffolding etc complete

Nos 38.00

54 Providing and fixing NIRALI stainless steel highgloss kitchen sink confirming to IS 13983 : 1994of size 500x1000mm bowl depth 200mm ,withsingle bowl drain board, M.S/C.I brackets, stainlesssteel plug 40mm, painting of fittings and brackets,cutting and making good the wall and floorwherever required, including cost of materials,labor complete as per specifications.

Nos 12.00

B Total for Water supply & Sanitary Works




C ELECTRICFICATION WORKS

A Point WiringSupplying 2mm thick 19mm dia PVC conduit withrequired accessories before casting roof/columnand fixing on wall after groove cutting and wiringusing 2 runs of 1.5Sqmm & 1 runs of 1.5Sqmmcopper wire and with all the materials required forlaying of conduit and wiring such as screws,bends, deep junction boxes PVC bushings andrawl plugs / Phil plug / wooden plug / saddle at aninterval of 600mm U or J hooks, CMPLASTERING, round block and sufficient loosewire of 650/1100V as applicable for concealedsystem. Two / three in a row shall comprise of 2/3round block. The rate shall include the cost ofsupply & fixing modular type Anchor Roma/ Cona/crab tree make switch & switch box with coverplate. Wires shall be of Anchor / Finolex make.

1. No. of 1.5 sqmm wires drawn in 19mm diaconduit shall not be more than five Nos. wires.2. Where more than five No. wires are to bedrawn, 25mm dia conduits shall be used.3. The conduits shall not be laid touching eachother a minimum of 1.5” gap shall be providedbetween the conduits for concrete filling betweenthe conduits.4. The switch shall be connected only in phasewire for Phase ‘ON’/ ‘OFF’.5. Red colored wire for phase, Black colored wirefor Neutral & Green colored wire for Earth shall beused for entire works for easy identification.6. In a circuit the total No. of points shall notexceed 15 nos the total load shall not exceed800W.7. The circuit wires shall be terminated in DBusing banana lugs.8.Wires used shall be with out joints in betweenthe point lengths9. The looping shall be done by using 10A ratedPVC connectors in the switch Boxes.10. For circuits, separate phase & neutral wireshall be used with separate earth wire.11. Work shall be done by Licensed wire men.12. Where points are for the fittings to besuspended from the ceiling, the points shall belocated at one of the knock out positions of thefixtures to avoid external wiring from junction boxto the fixture.




13. The conduit routes shall be such that theconduit lengths & overlapping shall be at aminimum as per the drawing. 14. Wherever point length is more than 6.0 m. theexcess length will be accounted as lighting circuit.

1.1 Point for 1 light point controlled by 1 no. switch asindicated in drawings

pt. 402.00

1.2 Point for 2 light point controlled by 1 no. switch asindicated in drawings.

pt. 25.00

1.3 Point for 3 light point controlled by 1 no. switch asindicated in drawings.

pt. 23.00

1.4 Point for One light controlled by 2 Nos switch 2wayswitch.(2Way point)

pt. 33.00

1.5 Same as 1.3 but for electric bell point with 1No bellpush near the door and electric buzzer at thelocation as indicated in the drawing

pt. 36.00

1.6 Same as item no 1.2 but for ceiling fan point with1No MS hook box and 1No stepped type electronicfan regulator.(One way Fan point)

pt. 47.00

1.7 Same as item no 1.4 but for ceiling fan point with1No MS hook box and 1No stepped type electronicfan regulator.(Two way Fan point)

pt. RO

1.8 Same as item no 1.2 but for exhaust fan point with1No 3pin socket near the point.

pt. 42.00

1.9 Supply & fixing modular 1No 3pin 5A socket with1No 6A switch in the light control switch box withall required inter connecting wires & complete asrequired(dependent)

pt. 109.00




1.10 Independent 3pin 5A socketSame as item No. 1.10 above but for independentpoint, with circuit looped from the nearest switchbox.

pt. 183.00

1.11 3pin 15A socket with switch in kitchenSupply & fixing modular 1No 15A socket with 1No16A switch fixed in modular type switch box withcover plate, with all required inter connecting wires& complete as required

pt. 124.00

1.12 3pin 15A socket in bath roomsSupply & fixing modular 1No 15A socket fixed inmodular type switch box with cover plate, with allrequired inter connecting wires & complete asrequired

pt. 1.00

1.13 16A Control switch with neon indicationSupply & fixing modular 1No 16A switch with neonindication fixed in modular type switch box withcover plate, with all required inter connecting wires& complete as required

pt. 1.00

1.14 3pin 20A Metal clad socket for A/CSupply & fixing 1No modular type 20A 3pin metalclad socket with 1No 20A SPMCB fixed in modulartype switch box with cover plate, with all requiredinter connecting wires & complete as required

pt. 42.00

1.15 Computer SocketSupply & fixing modular 3Nos 3pin 5A socket with1No 10A switch in 8Module switch box, cover plateand with all required inter connecting wires &complete as required

pt. 36.00

Sub Total to electrical abstract




B Circuit & Mains2.1 Lighting Circuit

Supplying and laying 19mm of heavy gauge PVCconduit pipe with suitable size bends, metaljunction boxes, adhesive paste etc and runningbefore concreting the slabs. The conduit should betied to the reinforcement rods by using binding wireand un used ways of junction boxes and pipe endsshould be covered using PVC end enclosures/capand run with 18 SWG GI fish wire run throughoutthe conduit wherever necessary. And supply anddrawing 2 runs of 2.5Sqmm and 1 run of 1.5SqmmPVC insulated 650/1100V multi stranded copperconductor wire in already laid conduit. (open orconcealed system of wiring). conduit shall be ofVIP / Universal / Atul Make and wires shall be ofFinolex / Havels / Anchor / L & T Make.

M 2606.00

2.2 Power circuit: Same as item No 2.1 above but 2runs of 4 Sqmm and 1 runs of 1.5Sqmm PVCinsulated multi stranded copper conductor wire in25mm dia 2mm thick PVC conduit concealed inceiling /wall for power points in kitchen and bathrooms.

M 1546.00

Service Mains (Rooms and CDBS)2.3 Same as 2.1 , but with 2 runs of 6.0Sqmm & 1 runs

of 2.5Sqmm multi stranded copper conductor wirefrom MDB to Room DB in 25mm dia PVC conduit.

M 625.00

2.4 Same as 2.1 , but with 2 runs of 10.0Sqmm & 1runs of 4.0Sqmm multi stranded copper conductorwire from MDB to Room DB in 25mm dia PVCconduit. To Suits and Executives rooms

M 315.00

2.5 Same as 2.1 , but with 4 runs of 4.0Sqmm & 2 runs of 2.5Sqmm multi stranded copper conductor wirefrom MVP to CLDB in 25mm dia PVC conduit.

M 15.00

2.6 Supply of following sizes of 1.1KV grade PVCinsulated, sheathed, galvanized, steel wire/steeltape armoured Aluminium conductor cable withPVC outer sheeting complete confirming to IS1554

2.6.1 3C x 6Sqmm copper cable for sump motors m 100.002.6.2 4C x 6Sqmm copper cable for Bore well m 100.002.6.3 4C x 16Sqmm for Lift m 120.002.6.4 4C x 35Sqmm for MDBs m 75.002.6.5 4C x 25Sqmm Copper cable for UPS Panel m 60.00




2.7 Laying of following sizes of cables in duct/ on cabletray using all fixing accessories such as saddles,screws etc.

2.7.1 3C x 6Sqmm copper cable for sump motors m 100.002.7.2 4C x 6Sqmm m 100.002.7.3 4C x 16Sqmm for Lift m 120.002.7.4 4C x 35Sqmm for MDBs m 75.002.7.5 4C x 25Sqmm Copper cable for UPS Panel m 60.00

2.8 Supply & providing cable end termination for the

following sizes of 1.1KV grade PVC insulated,sheathed, galvanized, steel wire/steel tapearmoured cable with PVC outer sheeting completewith suitable size of copper lugs, gland, Bolt & Nutincluding earthing of the gland & crimping the coreto the lug for proper contact & complete asrequired.

2.8.1 3C x 6Sqmm copper cable for sump motors No 2.002.8.2 4C x 6Sqmm No 2.002.8.3 4C x 16Sqmm for Lift No 2.002.8.4 4C x 35Sqmm for MDBs No 6.002.8.5 4C x 25Sqmm Copper cable for UPS Panel No 8.00





C Main panel, Energy meter board and DBs3.0 Supply, installation, testing & commissioning of the

following MV panel comprising of the incomingcontrol & outgoing control switches as indicated foreach panel with bus bars, cable alleys, indicationlamps, ammeter & voltmeter as specified. The MVpanel shall be of indoor, floor mountable, freestanding, dust & vermin proof cubicle typeconstruction using 14 SWG MS sheet. The MSsheet shall be cleaned in seven tank process fordegreasing, desulfating, dust removing etc. Thebus bar shall be supported on SMC / DMCsupports & shall withstand a fault current of 50KA.Bus bars shall be of Alu. make of proper size tosuit for the current ratings. Each cubicle shall beprovided with concealed hinged front door withneoprene gasket to ensure protection from dust.The side edges on the bus alley & cable alley shallbe properly covered with sleeves / gaskets. Theswitches shall be of L&T / English Electric Make.

3.1 Main panelIncoming400A 4P Auto Change Over Switch - 1NoSurge Protector - 1.4KV400A TPN Alu. Bus barOutgoing125A TPN SFU with HRC Fuse - 10Nos63A TPN SFU with HRC Fuse - 6Nos32A TPN SFU with HRC Fuse - 3Nos32A DP MCB - 6 No'sMultiData Meter with 400/5A CTs - 1SetIndication lamp with toggle switch - 3No's (1sets) SET 1.00

3.2 Auto Power Factor Improvement Capacitor PanelIncoming125A TPN SFU with HRC Fuse - 1Nos150A TPN Alu. Bus bar in tamper proof boxMicroprocessor based 8Stage Power factorcontroller relay - 1No63A TPN SFU with HRC Fuse and 63A 3P heavyduty Contactors - 5Nos32A TPN SFU with HRC Fuse 32A 3P heavy dutyContactors - 2Nos5KVAR Capacitor Bank - 2Nos10KVAR Capacitor Bank - 3NosIndication lamp with toggle switch - 3No's (1sets)0-125A Ammeter with CTs and Selector Switch500V Voltmeter with selector switch SET 1.00




3.3 UPS PanelIncoming:63A 4P MCCB 25KA - 2Nos150A TPN Alu. Bus bar in tamper proof boxOutGoings:32A DP MCB 10kA - 12NosMulti Data Meter with 63/5A CTs - 2NosIndication lamp with toggle switch - 6No's (2sets) SET 1.00

3.4 Lift PanelIncoming63A 4P ELCB 100 mA - 1No63A TPN Alu. Bus bar in tamper proof box25A DP MCB - 1NoIndication lamp with toggle switch - 3No's (1sets) SET 1.00

3.5 12Way Vertical TPN MCCB DB Distribution Boardas MDBIncoming125A TPN MCCB - 1Nooutgoing32A DP MCB - 15No10A SPMCB -5 No SET 3.00

3.6 CLDB Incoming40A 4P RCBO 300mA -1Nooutgoing6/10/16A SPMCB - 12 No SET 1.00

3.7 Room DBIncoming32A 2P RCBO 100mA - 1Nooutgoing6/10/16A SPMCB - 8 No SET 36.00




3.8 Computer DBIncoming32A 2P RCBO 100mA - 1Nooutgoing10A SPMCB - 8 No SET 3.00

3.9 Lift machine DBIncoming20A SPNMCB - 1Nooutgoing10A SPMCB - 4 No16A SPMCB - 4 No SET 1.00


D Earthing4.1 Supplying fixing and wiring GI pipe earth electrode

for grounding using 40mm dia 2.9mm thick 2.5mlong GI pipe with GI funnel should be enclosed.The funnel should be enclosed in a CC chamber of400 X 400 X 400mm with a cast iron cover. Theearth electrode shall be of staggered holes 12mmdia and the electrode should be covered 150mm all-round with alternate layers of salt and charcoalfrom the bottom of the pipe to the bottom of the CCchamber. The connection from the electrode is tobe established through GI strip using GI bolt andnuts

set 20.00

4.2. Supplying and running 25X3mm GI strips forgrounding connections, using if necessary suitablesize clamps, bolt, nuts & washers etc

M 300.00





E Supply and installation of Light fixture & Fans

5.0 Supply and installation of fluorescent tube lightfitting of 4' 40W fluorescent tube of 230 V made ofMS sheet and stove enameled with heavy dutypolyfill aluminum choke, starter, locking type brasscontact holders, tubes mounted on foldable typesheet base fully wired. MakePhillips/Wipro/Bajaj/Tulip.

5.1 Single 4' 36W FTL box type fitting with all requiredaccessories, wiring and complete as required.Supply each. 54.00

Installation each. 54.00

5.2 Decorative 11W CFL Ceiling Fitting with allrequired accessories, wiring and complete asrequired.Supply each. 40.00


5.3 9W CFL lamp bulk head fitting with toughenedglasscover, wire guard ,lamp holder and lamp.Supply each. 6.00


5.4 Surface mounted 2x18W CFL Ceiling fitting with allrequired accessories, wiring and complete asrequired.Supply each. 66.00


5.5 Decorative 18W CFL wall bracket Fitting with allrequired accessories, wiring and complete asrequired.Supply each. 144.00





5.6 Decorative 13W CFL mirror light Fitting with allrequired accessories, wiring and complete asrequired.Supply each. 79.00


5.7 Decorative 3W LED Night light with all requiredaccessories, wiring and complete as required.Supply each. 36.00


5.8 Supply and Fixing of exhaust fan of 300mm 1440RPM of suitable size with bracket blades completefor heavy duty including making opening in walland making good with all requored fixingaccessories for toiletsSupply each. 42.00


5.9 Supply and Fixing of exhaust fan of 380mm 1440RPM of suitable size with bracket blades completefor heavy duty including making opening in walland making good with all requored fixingaccessories for toiletsSupply each. 1.00


5.10 Supply and Installation of 1200mm sweep ceilingfan of 5 star rated. Make shall be of Usha/CGSupply each. 43.00






F Out door Campus lighting LT PVC Cables6.1 Supply of 1.1kv grade following sizes PVC

insulated, and over all sheeted, stranded copperconductor, flat steel strip /wire Armoured cablesconforming to IS: 1554 Part I (with latestamendments )and of following sizes. The cable willbe of ISI certification mark . Cable shall be ofUNIVERSAL / NIFCO / CCI/ GLOSTER make.

3C X6Sqmm PVC cableSupply M 750.00

6.2 Laying of following sizes of PVC cables, 1.1Kvgrade FRLS cables/ PVC insulated PVC sheetedcables / XLPE cables Armoured/ unarmoured,copper/copper conductor cables in groundincluding earth excavation for cable trench andproviding bricks on side and top of the cable &sand around the cable as per the standard practiceand as detailed in technical specification.

3C X 4Sqmm PVC cable m 750.00

6.3 END TERMINATIONS OF LT CABLES Providing end terminations for 2/3/3-1/2/4 core,1.1KV grade PVC insulated, PVC sheathed ArmouredAluminium conductor cables including supply ofcable gland, compression type lugs, using crimpingtool, insulation tape and identification tags, clampsand other materials and tools required completewith terminal connections earthing of glands andas required.

3C X 4Sqmm PVC cable No 48.00

6.4 Supply of Campus Light fixtures

Supply of integral type 2x18W CFL post top lanternconsisting of spun Aluminium canopy and openacrylic diffuser and cast Aluminium spigot includinglamp holder control gear and accessories withpolyester filled copper wound ballast, capacitor,igniter, fuse etc. prewired up to terminal blockincluding lamp of Philips/ Wipro/ k-lite make.

each 24.00




6.5 Fixing of Campus light fixturesInstallation of post top lantern on 80mm dia 4.8mhigh class 'c' GI pipe including cutting, threading,welding, earth excavation, providing concretepedestal, coping, supply of GI pipe, WP terminalbox of suitable size inter connecting wires, fuse,terminal block, 50mm dia GI sleeve and completeas required.

each 24.00

6.6 EARTHING :Providing coil/spiral earthing using 8SWG GI wireburied to a minimum depth of 1.5m withexcavation, refilling and connecting GI wire to thepole using GI bolt and nut and complete asrequired.

each 24.00


G Telephone & TV wiring7.1 Supply and laying of 25mm dia PVC conduit in

Ceiling / Wall / Modular Furniture/ Floor for TVAntenna points with all required fixingaccessories.including 18 SWG GI wire.Supply m 3310.00

Installation m 3310.00

7.2 Supply & fixing of RJ-11 Telephone point outletsocket, inclusive of Modular Box and Cover Plate,with inter connections as required & as directed byEIC.Supply each 74.00

Installation each 74.00

7.3 Supply & fixing of RJ-45 Data point outlet socket,inclusive of Modular Box and Cover Plate, withinter connections as required & as directed by EIC.

Supply each 36.00


7.4 Supply & fixing of TV antenna outlet socket,inclusive of Modular Box and Cover Plate, withinter connections as required & as directed by EIC.

Supply each 36.00





7.5 Supply & installation of 20 PAIR TJB with mountingMS Box of suitable size including supply of allfixing materials & complete as required.Supply each 3.00


7.6 Supply & installation of 50 PAIR TJB with mountingMS Box of suitable size including supply of allfixing materials & complete as required.Supply each 1.00


7.7 Supply & installation of 200 PAIR TJB withmounting MS Box of suitable size including supplyof all fixing materials & complete as required.Supply each RO

Installation each RO

7.8 Supply & installation of 14 way TV splitter box withMS Box of suitable size to house 100W boosterincluding supply of all fixing materials & completeas required.Supply each 3.00


7.9 Supply & drawing of 2 pair telephone cableSupply m 1850.00





7.10 Supply & drawing of 20 pair telephone cableSupply m 115.00


7.11 TV coaxial cable RG 6Supply m 1650.00


7.12 Supply & drawing of CAT-6E cableSupply m 1080.00


7.13 Supply & installation of EPABX to suit for 10Nosincoming and 100Nos outgoings

Each RO


H External Power supply

8.1 Load Break Switch ( LBS)Outdoor 11KV Load Break SwitchesSupply, Installation, testing & commissioning of3Nos 11KV, 400 Amps with minimum 250 MVAshort circuit capacity, 3 Ph., 50Hz, AC supply HTload break switch fuse unit, dust & vermin proofand totally enclosed in sheet steel housing,interlocked, horizontal indoor, floor mounting frontmanually operated type, with 3No HT fuses of 25Amp rating.The switch fuse unit shall be complete with Epoxyinsulators, interlocked earthing switch, auxiliarycontacts rear, cable entry box, electrolyticaluminium busbars within on hygroscopic & highdielectric strength SMC/FRP / porcelain busbarsupports housed in sheet steel enclosure, Fusepuller etc.. Switch shall trip off even when onefuse blows off complete with fire/heat resistantcoating and painting with approved syntheticenamel paint, complete as required and asdirected by EIC

Each 1.00

Installation set 1.00

8.2 Supply & Installation of 11Mtr long single polestructure (Resin pole) with the following mountedon the pole using necessary 11KV insulators,hardware like MS channels brackets angles etc11KV 400A GOS - 3No11KV 16A Drop out fuse - 1set




9KV lightning Arrestor - 1No set 1.00

8.3 Supply , Installation, testing & commissioning ofthe 250KVA type 50 Hz Copper wound, Indoorplinth mountable type, delta / star connected, oilimmersed, naturally oil cooled, core typeTransformer, with no load voltage ratio of 11,000 /433 V., an no-load tap changing switch with locking arrangement & which is operated externally withvoltage variation of in steps of +/- 2.5%, +/-5.0%, -7 5%Transformer shall be suitable for operation in anambient up to 40* C & shall be supplied withneutral terminal on LT side, & all accessories suchas silica gel breather, magnetic oil gauge,conservator dial type temperature indicator, cableend boxes on LT side & HT side, earthingterminals, explosion vent, drain value with plug, asper IS 335 (with latest amendments) in all respectslike i insulation levels, temperature rise, impedancevoltage & lossesSupply set 1.00

Installation of transformer on brick base set 1.00

8.4 Supplying and laying of 11 kV XLPE insulated,11KV H.T cable of 3 C x 95 sqmm size, with XLPEsheathing and PVC over all served, Steel striparmoured, multi stranded aluminium conductorcable in the already laid Hume Pipe./ in groundincluding trench excavation for a depth of 1M andproviding sand caddapa tiles for cable protectionincluding refilling and compacting as requiredwhere cable is routed in ground

Rmtr 600.00

8.5 Supplying and making of In door 3 C x 95 sqmm,11 kV XLPE, heat shrinkable push on / resin casttermination suitable for 11KV H.T cable as per themanufacturer details & complete as required for 3C x 95 sqmm XLPE cable with jointing kit includingaluminium lugs and other joining materials.

Each 4.00

8.6 Supplying and making of Out door 3 C x 95 sqmm,11 kV XLPE, heat shrinkable push on / resin casttermination suitable for 11KV H.T cable as per themanufacturer details & complete as required for 3C x 95 sqmm XLPE cable with jointing kit includingaluminium lugs and other joining materials.

Each 4.00




8.7 MV PanelSupply, design, fabrication, testing &commissioning of dust and vermin proof, out door,front operation type main panel comprising ofcubicle chambers for mounting 500V, 50Hz, ACsupply, TPN MCCB of cubicle type. The panel shallbe fabricated using 14SWG CRCA sheet steel,cutting, welding, fabrication including interchamberfire barriers, doors with gasket & locking facility,silicon based fire/heat resistant coating andpainting of required colour synthetic enamel paint.Before painting, the sheet shell shall under goseven tank process for cleaning the surface fromrust, grease layers. The MCCB's with rotary handleand housed in separate cubicle with doorinterlocking arrangementThe bus bar shall be of High conductivityaluminium with suitable cross section to suite thecurrent rating with colour coded insulationwrapping as specified enclosed in 14SWG CRCAsheet steel dust & vermin proof enclosure &supported on non - hygroscopic high di-electricSMC/DMC busbar supports to with stand asymmetric fault level of 50KA. The MCCBterminals shall be suitably brought out to the cablealley using suitable size of colour coded aluminiumstrips fixed on SMC/DMC supports suitable tofacilitate termination of cables with bolts & nutsarrangement. The panel shall be fabricated as perthe technical specificationsMain LT PanelIncoming:0-8000mA CBCT with ELR - 1set400A TPN MCCB 35kA - 1No400A TPN Aluminium Busbar - 1setIndication lamp with toogle switch - 1set set 1.00

8.8 LT XLPE CablesSupply of following sizes of 1.1kv grade XLPEinsulated, and over all sheeted, strandedaluminium conductor, flat steel strip / wirearmoured cables conforming to IS: 7098 Part I(with latest amendments ) and of following sizes.The cable shall be of ISI certification mark .

8.8.1 3.5c x 70 sqmm m 20.00

8.8.2 3.5c x 120 sqmm m 35.00

8.8.3 3.5c x 240 sqmm m 90.00




8.9 Laying of following sizes of 1.1kv grade XLPEinsulated, armoured cables in the already laidHume Pipe/routing over wall / column/ ceiling usingsaddles and screws etc.,

8.9.1 3.5c x 50 sqmm m 20.00

8.9.2 3.5c x 120 sqmm m 35.00

8.9.3 3.5c x 240 sqmm m 90.00

8.10 END TERMINATIONS OF LT CABLES Providing end terminations for the following sizesof, 1.1 KV grade XLPE insulated aluminiumconductor cables including supply of cable gland,compression type lugs, using crimping tool,insulation tape and identification tags, clamps andother materials and tools required complete withterminal connections earthing of glands and asrequired and as directed by Consultant / EIC.

8.10.1 3.5c x 50 sqmm m 2.00

8.10.2 3.5c x 120 sqmm m 2.00

8.10.3 3.5c x 240 sqmm No 4.00

8.11 Supply & fixing of 100mm dia, class 'B' GI pipe tobe fixed on over head RCC pole/wall with allaccessories like clamps, bolts and nut saddlesetc.,

m 6.00

8.12 Trench for XLPE CableDigging the ground to a depth of 0.6M below GL tolay the 1.1KV XLPE cable and refilling the trenchwith the earth mass, consolidating and makinggood including supply and placing the cadapa tileson top & bricks on the sides of the cable.

m 50.00

8.13 Liaison ChargesWork includes the following services:Obtaining Power Sanction for 100kVA power,Approval of Line work estimates, Approval ofexecution of Line work estimates, Approval ofnecessary Electrical Drawings from the Electricalinspectorate, Approval of HT and LT installationworks from the Electrical Inspectorate, Obtainingpollution control board certification for the DG,Energising the service and taking all kinds ofapprovals with the concerned authorities

LS 1.00





I GENERATOR POWER SUPPLY9.1 Supply, Installation, Testing & Commissioning of

100KVA 3 phase 415 V , 50 c/s DG set comprisingof the following: EngineEngine of suitable capacity to generate 100 KVApower at 0.8 P.F & shall be with the following.a) Fly wheelb) Flexible couplingc) Corrosion resistance radiatord) Air cleanere) Fuel pump f ) Fuel filterg) Hydraulic governorh) 24 V starting batteryi ) Oil indicatorj ) Low oil pressure protectionk) High water temperature protectionl ) Oil pressure gaugem) Oil temperature gaugen) Water temperature gaugeo) Exhaust silencerp) Residential silencerq) RPM indicatorr) Starting key s) Mounting bare frame with anti vibration pad.Generator/ AlternatorCapacity:100 KVA 3 phase 415 V 50 c/s at 0.8 PF.Type:

a)250A TPN MCCB with1000mA ELR- 1 No. with protection against over load & earth fault.b) 0-500 V 3 ph. voltmeter - 1 No.

c) 0-160A 3 ph. ammeter with 250/5A CTS - 1No.

d) 50 c/s frequency meter 1No

e)P-F meter-1No.f) Watt hour meter - 1 No.g) Energy meter & indication lamp. - 1 No.The work includes supply of necessary fuel line,interconnecting power cable & control cable, fueltank of sufficient capacity & necessary accessoriesto fix the exhaust pipe. Including Supply, installation and testing ofAcoustic enclosure for 82.5 KVA DG, to bringdown the noise level to 72 db at a distance of 1.0mts.

Brush less type self excited, self regulated & drip proof. Voltage regulator shall be provided with the following accessories.




DG shall be of Cummins/ Kirloskar Greensupply set 1.00

erection set 1.00

Installation exhaust stack with supports upto15.0Mtr

Set 1.00


J Fire Alarm And Public Address System

10.1 Supply and laying of 25mm dia PVC conduit inCeiling / Wall / Floor for PA System with allrequired fixing accessories.including 18 SWG GIwire.Supply m 250.00


10.2 Supply and laying of 25mm dia MS conduit inCeiling / Wall / Floor for Fire alarm points with allrequired fixing accessories.including 18 SWG GIwire.Supply m 75.00


10.3 Supply and installation of 4Zone fire alarm controlpanel with all interconnections as required.

Each 1.00

10.4 Supply, Erection, Testing & Commissioning ofManual Call point

Each 5.00

10.5 Supply, Erection, Testing & Commissioning ofSounder/hooter

Each 5.00

10.6 Supply and drawing of 2runs of 1.5Sqmm MSCCwire in existing MS conduit for fire control wiring

Rmtr 145.00

10.7 Supply and drawing of 2 core 1.0 sqmm audioscreened multi stranded copper conductor, audiocable.

Rmtr 275.00

10.8 Supply and installation, testing and commissioningof 2way communication speaker with mike with allrequired accessories and control wiring asrequired.

Each 5.00




10.9 Supply and installation, testing and commissioningof Professional grade amplifier with 2 mikes and10auxiliary inputs the amplifier shall be providedwith individual volume control and auxiliary inputjacks on back side.

Each 1.00


K UPS11.1 Supply, commissioning, testing and installation of

15KVA UPS system, Fully digital andmicroprocessor control, High performance true on-line double conversion (VFI tech.) with 100%capacity advance rectifier with harmonic filter toachieve harmonic distortion < 5% input iTHD,IGBT/PWM inverter with galvanic isolationtransformer, with high standards of reliabilityconfirming to international standards such asIEC/EN/VDE, CENELEC, UNI ISO. The systemshall have high operating efficiency of better then95%; with standard static and manual maintenancebypass. (3Ph – 3Ph) along with SMF batteries ofrequired capacity for approx. 30 minute back up atfull load conditions complete with interconnectinglinks, battery racks and DC cable.

UPS shall be of ON line type the efficiency shallbe 90%, out wave form shall be of pure sine wave& Zero transfer time

Each 2.00





ABSTRACT FOR ELECTRICAL WORKS

A Point Wiring

B Circuit & Mains

C Main Panel and DBs.

D Earthing

E Supply and installation of Light fixture & Fans

F Out door Campus lighting LT PVC Cables

G Telephone & TV wiring

H External Power Supply

I Generator power supply

J Fire Alarm and Public Address System

K UPS

C Total for Electrification Works




D BOREWELL WORKS

1 Sinking Borewell of 165mm dia clear using superfast hydraulic rif of capacity 250 PSIG and above900 CMF and above in all strata including overburden upto 20 m. fixing of casing pipes, collarsand cap with necessary cuttung, threading andwelding including transportation of rig andsupporting vehicles, crew charges and cost ofconsumables etc., complete including yield testingat the final depth with a minimum working ofcompressor for one house (excluding cost ofcasing pipes, collars, cap etc.,)

Point 1a) 0 to 50 mts Rmt 50.00

Point 1b) 50 to 100 mts Rmt 50.00

Point 1c) 100 to 150 mts Rmt 50.00



2 Supplying and fixing of 175mm dia 3mm thick.Normal bore medium black ERW casing pipes (B-Class) black electric resisting containers weldedMS tubes medium grade confitming to IS1239/1979 (part-1) Amendment 1 to 5 and inrandom length of 4 to 7 mtrs. With all lead and lifts.

Point 1 Rmt 45.00

a) CollarPoint 1 Each 10.00

b) CapPoint 1 Each 1.00

3 Supplying and fixing 75mm int dia HDPEpipe16kg/Sq cm with stainless steel end fittings etccomplete.

Rmt 92.00




4 Supplying and fixing stainless steel submercible pump set of 5HP capacity and Stages as permanufacturers specifications of approved make .

Set 1.00

5 Supplying and laying 3 core flat submercible cable5.5 sqmm.

Rmt 225.00

6 Providing and fixing Electronic Control panelboard with MCB's

Set 1.00

7 Providing and fixing 175mm dia foot valve etccomplete.

Set 1.00

D Total for Borewell works




E RAIN WATER HARVESTING WORKS1 Providing and Constructing Rainwater harvesting

collecting points done with including excavationand refilling to insert RCC precast rings of 1.50 mdia and depth of 0.45m of 8 nos, with filling 40mmmetal granite, 20mm metal granite and sand ofheight 1.10m individually with covering the topsurface using RCC precast Slab as per design anddrawings, filling the sides with boulders andavailable earth and shifting the excess earthoutside the site premises

Each 4.00

2 Providing and fixing 110mm dia PVC pipe ofSupreme Make with bends, Tee and joints &specials with solvent including scaffolding etc,complete as per directions.

Rmt 200.00

3 Providing and fixing Rain water Filters of Rain topmake of 1500 sft capacity each.

Each 6.00

E Total for Rainwater Harvesting Works




F PATHWAYS

1 Earth work excavation for foundation of buildings,culverts, water supply, sanitary lines and electricalconduits either in pits or in trenches 1.5m andabove in width, in hard soil not exceeding 1.5m indepth including dressing the bottom and sides ofpits and trenches,stacking the excavated soil clearfrom edges of excavation with lead upto 50m.afterbreaking of clods complete as per specifications.

Cum 62.00

2 Filling available excavated earth (excludingrock)in sides of foundations upto plinth in layersnot exceeding 20cms.in depth,compacting eachdeposited layer by ramming after watering withlead upto 50m and lift upto 1.5m including cost ofall labour complete as per specifications

Cum 16.00

3 Providing and laying heavy duty Cobble stones75mm thick interlock pavers,using cement andcourse sand for manufacture of blocks of approvedsize,shape and colour with a minimumcompressive strength of 281 kg per sqm over50mm thick sand bed (average thickness) andcompacting with plate vibrator having 3 tonescompaction force thereby forcing part of sandunderneath to come up in betweem joints,finalcompaction of paver surface joints into its finallevel,including cost of materials, labour abd HOMof machineries complete as per specifications.

Sqm 166.00

4 Providing and fixing pre cast solid cement concretekerb stone made out of C.C 1:2:4 with top andbottom width 114 and 165 mm respectively,400mm high and 450mm in length finished withCM 1:3 plastering and finishing cutting, includingform work, curin, cost of all materials, labour, hirecharges of machinery, loading, unloading, lead andlift, transportation etc., complete.

Nos 203.00




5 Providing and applying ready mix priming coat overconcrete / masonry / asbestos cement sheet /plastered surfaces including preparing the surfaceafter throughly cleaning of oil, grease, dirt andother foreign matter, and sand papering includingcost of materials, labour, complete as perspecifications.

Sqm 92.00

6 Providing and applying floor painting with readymix paint in two coats (excluding priming coat) onnew concrete / asbestos cement sheet / plasteredsurfaces brushing to give an even shade afterpreparing the surface after throughly cleaning ofoil, grease, dirt and other foreign matter, and sandpapering including cost of materials, labour,complete as per specifications.

Sqm 92.00

F Total for Pathways




G ROADS

1 Earthwork excavation by manual means in hardsoil invloving an average horizontal throw upto 2meters and an average lift upto 0.5m, excavatedsurface levelled and sides neatly dressed, thedisposed earth to be levelled neatly after breakingof clods complete as per specifications.

Cum 378.00

2 Providing, Laying, Spreading and compactingstone aggregates of specific sizes to water boundmacadam specification including spreading inuniform thickness, hand packing, rolling with 3wheeled steel/ vibratory roller 8-10 tonnes instages to proper grade and camber, applying andbrooming requisite type of screening/ bindingmaterials to fill up the interstices of coarseaggregate, waterproofing and compacting to therequired density.Material (Refer table 400- 7,8 & 9)Using Screening Type- A (13.2mm agg.) Grading -II (Manual)Clause :404

Cum 168.00

3 Providing, Laying, Spreading and compactingstone aggregates Using Screening Type- B (11.2mm agg.) Grading -III (Manual)

Cum 84.00

4 Cleaning the existing WMB road surface includingremoving of binding materials and other foreignmatter with wire brushes and small picks,sweeping with brooms or soft brushes and finallydusting with old gunny bags and/ or compressedair, to receive bituminous treatment including costof all materials, labour, HOM of machineriescomplete as per specifications.

Sqm 840.00

5 Providing and applying primer coat with bitumenemulsion on prepared surface of granular Base oflow porosity such as WBM and WMM includingclearing of road surface and spraying primer at therate 1.05 kg/ sqm using mechanical means.

Sqm 840.00




6 Providing and laying surface dressing as wearingcourse in single coat using crushed stoneaggregates of specified size on a layer ofbituminous binder laid on prepared surfaceincluding cleaning with mechanical broom hydraulic and rolling with 8-10 tonne smooth wheeled steelroller, 19mm nominal size chipping as per MORTHspecification clause No. 510 complete in allrespects. (Bitumen= 1.00 Kg/ Sqm Metal = 0.01)

Sqm 840.00

7 Providing and laying bituminous concrete 40mmthick with 60-70 TPH hot mix plant using crushedaggregates of specified grading, premixed withbituminous binder @ 5.4-5.6 percent of mix andfiller, transporting the hot mix to work site, layingwith a hydrostatic paver finisher with sensor controlto the required grade, level and alignment, rollingwith smooth wheeled, vibratory and tandem rollersto achieve the desired compaction.

Cum 42.00

8 Providing and fixing pre cast solid cement concretekerb stone made out of C.C 1:2:4 with top andbottom width 114 and 165 mm respectively,400mm high and 450mm in length finished withCM 1:3 plastering and finishing cutting, includingform work, curin, cost of all materials, labour, hirecharges of machinery, loading, unloading, lead andlift, transportation etc., complete.

Nos 952.00

9 Providing and applying ready mix priming coat overconcrete / masonry / asbestos cement sheet /plastered surfaces including preparing the surfaceafter throughly cleaning of oil, grease, dirt andother foreign matter, and sand papering includingcost of materials, labour, complete as perspecifications.

Sqm 429.00




10 Providing and applying floor painting with readymix paint in two coats (excluding priming coat) onnew concrete / asbestos cement sheet / plasteredsurfaces brushing to give an even shade afterpreparing the surface after throughly cleaning ofoil, grease, dirt and other foreign matter, and sandpapering including cost of materials, labour,complete as per specifications.

Sqm 429.00

G Total for Roads

H SITE DEVELOPMENT WORKS1 Earth work excavation for foundation of buildings,

culverts, water supply, sanitary lines and electricalconduits either in pits or in trenches 1.5m andabove in width, in Hard soil not exceeding 1.5m indepth including dressing the bottom and sides ofpits and trenches, stacking the excavated soil clearfrom edges of excavation with lead upto 50m. afterbreaking of clods complete as per specifications.

Cumt 142.00

2 Filling available excavated earth (excluding rock)in sides of foundations upto plinth in layers notexceeding 20cms in depth, compacting eachdeposited layer by ramming after watering withlead upto 50m and lift upto 1.5m including cost ofall labor complete as per specifications

Cumt 71.00

3 Flooring with 100mm thick rough dressedchappadi granite using cement mortar 1:6, 25mmthick laid to line and level and jointed with cementslurry mixed with pigment to match the shade ofthe slab, including cost of materials, labour, curingcomplete as per specifications.

Sqmt 132.00

4 Flooring with 25mm thick Ultra tiles using cementmortar 1:6, 25mm thick laid to line and level andjointed with cement slurry mixed with pigment tomatch the shade of the tiles, including cost ofmaterials, labour, curing complete as perspecifications.

Sqmt 158.00




5 Providing and constructing Precast concrete solidblocks with compressive strenght not less than 35Kg/Sqm with cement mortar 1:4 masonry (Quion,Jamb, Closer blocks) with solid concrete blocks ofsize 40 x 20 x 20 cms confirming to IS 2185 /1965 in super structure including cost of materials ,labour charges, scaffolding, curing complete as per specifications, including parapet wallls.

Sqmt 158.00

6 Providing 18mm thick plaster in single coat withcement mortar 1:6, to brick masonry includingrounding off corners wherever required smoothrendering, providing and removing scaffolding,including cost of materials, labor, curing completeas per specifications, including parapet walls. ( For External Walls )

Sqmt 237.00

H Total for Site Development Works




PROPOSED CONSTRUCTION OFRESEARCH SCHOLARS HOSTEL FOR INDIAN STATSTICAL INSTITUE, BANGALORE CAMPUS

ABSTRACT

Sl Particluars

A CIVIL WORKS Rs

B WATER SUPPLY & SANITARY WORKS Rs

C ELECTRIFICATION WORKS Rs

D BOREWELL WORKS Rs

E RAIN WATER HARVESTING WORKS Rs

F PATHWAYS Rs

G ROADS Rs

H SITE DEVELOPMENT WORKS Rs

GRAND TOTAL

TOTAL IN WORDS

Signature:

Date:

Company Seal:

Rs

Amount


Documents

2 OF 2 BILL OF QUANTITIES FOR THE CONSTRUCTION OF … · Indian Statstical Institute Alur Associates SL PARTICULARS FLR UNIT QNTY RATE AMOUNT 15 Providing and removing centering,