2015 PlantPAx System Estimator Update
2015 PlantPAx System Estimator UpdateNew Virtualization sizing
calculationsEnhanced assignment of I/O to Intelligent Motor
ControlsNew ability to add network switch to controller and I/O
locationsFactoryTalk Historian and FactoryTalk AssetCentre now
default on new systemsUpdated controller sizing footprints
Target Release: End of MayCopyright 2015 Rockwell Automation,
Inc. All Rights Reserved.PUBLIC12015 PSE UpdateNew Virtualization
sizing calculations
PSE calculates minimum virtual requirements for virtualization
of the PlantPAx System servers and workstationsSizing shown in
System Properties and reportsUser selects whether workstations are
to be virtualized (or just servers)Virtual sizing requirements
tunable from System PreferencesOVERVIEWBENEFITS123Simplifies sizing
of virtualized systems aligning with the latest recommendations in
the PlantPAx Selection Guide and Reference Manual. Copyright 2015
Rockwell Automation, Inc. All Rights Reserved.PUBLIC
2015 PSE UpdateEnhanced assignment of I/O to Intelligent Motor
ControlsSimplified workflow to map I/O configuration to Intelligent
Motor Control Devices:Enter in the number of IMC devices by type
and see the I/O count that is decremented from totalChange specific
IMC devices by locationHW Defaults allow you to exclude IMC from
BOM. System Preferences allows you to tune I/O mapping by
device.OVERVIEWBENEFITS12Easily generate a single BOM inclusive of
PlantPAx System and IMC devicesCopyright 2015 Rockwell Automation,
Inc. All Rights Reserved.PUBLIC
2015 PSE UpdateNew ability to add network switches to controller
and I/O locationsMore flexibility to layout network switches:Added
checkbox to include Stratix 5700 on Supervisory network aligned
with controllerAdded checkbox to include Stratix 5700 on I/O
network for an I/O locationOVERVIEWBENEFITS1Easily attach network
switches to your control and I/O panels and layout your networks in
IAB
2Copyright 2015 Rockwell Automation, Inc. All Rights
Reserved.PUBLIC
2015 PSE UpdateHistorian and AssetCentre now added by default
for new systemsNew systems include AppServ-Info element for
Historian by defaultNew systems include AppServ-AssetMgt with
Disaster Recovery by defaultAdded information messages when the
licensed tag count of FT Historian or licensed assets of
FactoryTalk AssetCentre dont match up with PSE calculated
valuesOVERVIEWBENEFITS1Default system is closer to typical system
configuration so that there is less steps to configure.
332Copyright 2015 Rockwell Automation, Inc. All Rights
Reserved.PUBLIC
2015 PSE UpdateUpdated controller sizing footprintsUpdated
location preferences with adjusted control strategy footprintsAdded
ability to account for I/O that will not be assigned to a Process
Object for sizingAdded details of what control strategies were used
to develop each footprint in the Help fileOVERVIEWBENEFITS1More
accuracy and clarity in the controller sizing calculations. 2
3Copyright 2015 Rockwell Automation, Inc. All Rights
Reserved.PUBLIC2015 PSE UpdateAdditional InfoCopyright 2015
Rockwell Automation, Inc. All Rights Reserved.PUBLIC
PUBLIC - 5058-CO900H Copyright 2015 Rockwell Automation, Inc.
All Rights Reserved.PUBLIC
2015 PSE UpdateAdditional InfoVirtualization sizing footprints
can be adjusted in system preferences workbookMCC Sizing I/O
assignments can be adjusted in system preferences
workbookOVERVIEW12Copyright 2015 Rockwell Automation, Inc. All
Rights Reserved.PUBLIC
2015 PSE UpdateAdditional InfoWhen using 1769-L24ER-QBFC1B, new
option in assign I/O to hardware to use embedded I/O on
controllerOVERVIEW1Copyright 2015 Rockwell Automation, Inc. All
Rights Reserved.PUBLIC
2015 PSE UpdateAdditional InfoNew option in hardware defaults to
exclude intelligent motor control devices from BOM if IMC devices
are existing or part of MCCOVERVIEW1Copyright 2015 Rockwell
Automation, Inc. All Rights Reserved.PUBLIC
