· 23. Plug the automatic day/night mirror harness 7-pin connector into the automatic day/night mirror. 24. Gentry pull back the headliner, and tuck the automatic day/night mirror

Publications No.

INSTALLATIONINSTRUCTIONS

Accessory Application

© 2015 American Honda Motor Co., Inc. – All Rights Re

VERSION 1

www.collegehillshonda.com
AUTOMATIC DAY/NIGHT
MIRROR

served. AII01797-23 (150

2016 HR-V

4) 0

Issue Date

APR 2015

PARTS LIST

Attachment KitP/N 08V03-T7S-100

Automatic day/night mirror harness

Harness cover

8 Wire ties

Clip(May not used)

Urethane tape

Fuse label

Ground bolt

Aluminum tape

Automatic Day/Night Mirror KitP/N 08V03-TR0-100A

Automatic day/night mirror

Accessory User’s Information Manual

1 of 148V03-T7S-1000-90

TOOLS AND SUPPLIES REQUIRED
Phillips screwdriver

Flat-tip screwdriver

Ratchet

10 mm Socket

Isopropyl alcohol

Shop towel

Diagonal cutters

Torque wrench

T20 TORX bit

Flashlight

Tape

10 mm Open end wrench

Scissors

White marker

Ruler

The following tools are available through the Honda Tooland Equipment Program. On the iN, click on: Service >Service Bay > Tool and Equipment Program, then enterthe number under “Search”. Or, call 888-424-6857.

• Trim Tool Set (T/N SOJATP2014)

• Plastic Trim Tool (T/N SILTRIMTL10)

Illustration of the Automatic Day/Night Mirror in theVehicle

QD42301AJ

AUTOMATIC DAY/NIGHTMIRROR

2A FUSE


2 of 14 AII01797-2

INSTALLATION

1. Disconnect the negative cable from the battery.

2. Loosen the TORX screw, and remove the rearviewmirror from the mirror mount.

Customer Information: The information in thisinstallation instruction is intended for use only by skilledtechnicians who have the proper tools, equipment, andtraining to correctly and safely add equipment to yourvehicle. These procedures should not be attempted by“do-it-yourselfers.”

QD42302BJ

TORX SCREW(Loosen.)

MIRRORMOUNT

REARVIEW MIRROR(Discard.)

3 (1504) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.

3. Remove the left and right lenses from the map light
console (four retaining tabs for each lens). Removethe two bolts.

With Moonroof: Remove the map light console. Thenunplug the vehicle connectors, and remove theswitch (four retaining tabs).

Without Moonroof: Remove the map light console(unplug the vehicle connector).

QD42303AJLEFT MAPLIGHT LENS

4 RETAININGTABS

2 BOLTS

MAP LIGHTCONSOLE

4 RETAININGTABS

RIGHT MAPLIGHT LENS

SWITCH

VEHICLECONNECTORS

4 RETAININGTABS

QD42304AJLEFT MAPLIGHT LENS

4 RETAININGTABS

2 BOLTS

MAP LIGHTCONSOLE

4 RETAININGTABS

RIGHT MAPLIGHT LENS

VEHICLECONNECTOR

© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII01797-2

4. Release the passenger’s sunvisor from thepassenger’s sunvisor holder.

5. Remove the passenger’s sunvisor holder:

• Wrap tape around the tip of flat-tip screwdriver.

• Release three retaining tabs on the passenger’ssunvisor holder.

QD42305AJ

PASSENGER’SSUNVISOR

PASSENGER’SSUNVISOR HOLDER

QC22003BJ


FLAT-TIPSCREWDRIVER

TAPE

3 RETAININGTABS(Push.)

3 (1504) 3 of 14

• While holding down the passenger’s sunvisor
holder as shown, use a flat-tip screwdriverwrapped with a tape to remove the passenger’ssunvisor holder (three retaining tabs).

QC22004AJ


Hold down.


FLAT-TIPSCREWDRIVER

4 of 14 AII01797-2

6. Remove the driver’s sunvisor (unplug the vehicleconnector):

• Pivot the driver’s sunvisor downward.


• Locate the slot in the base cover, and insert theflat-tip screwdriver into the slot. Push in and holdthe retaining tab.

• While holding the retaining tab, push up on thesunvisor and rotate it toward the door.NOTE: If the retaining tab does not stay pushedin, return the sunvisor to its original position andrepeat this step.

QD40301AJPush theretaining tab.

While pushing inon the tab, rotatethe sunvisortoward the door.

Make sure thetab slides intothe base cover.DRIVER’S

SUNVISOR

BASECOVERFLAT-TIP

SCREWDRIVER

TAPE

RETAININGTAB

FRONT

VEHICLECONNECTOR(if equipped)


7. Remove the driver’s sunvisor holder:

• Release three retaining tabs on the driver’ssunvisor holder.

• While holding down the driver’s sunvisor holderas shown, use a flat-tip screwdriver wrappedwith a tape to remove the driver’s sunvisorholder (three retaining tabs).

QC22003BJ

DRIVER’SSUNVISOR HOLDER

FLAT-TIPSCREWDRIVER

TAPE


QC22004AJ


Hold down.

DRIVER’SSUNVISOR HOLDER

FLAT-TIPSCREWDRIVER


If the vehicle is equipped with the side curtain airbags,continue with step 8. If not, go to step 11.

With side curtain airbags

8. Remove the driver’s A-pillar trim:

• Pull away the door opening seal from the driver’sA-pillar trim.

• Pull out on the driver’s A-pillar trim to releasethree clips.

QD40302BJ

Pullthe clip.

2 CLIPS

DRIVER’SA-PILLARTRIM

DRIVER’S A-PILLAR

DOOROPENINGSEAL(Pull away.)

DRIVER’SA-PILLAR TRIM

SECTION VIEW

3 (1504) 5 of 14

• To prevent clips from falling into the body panel
area, carefully insert a shop towel between thedriver’s A-pillar and the driver’s A-pillar trim.

• Slide the driver’s A-pillar trim upward, andremove the driver’s A-pillar trim.

• Remove the shop towel and any clips.

QD40303BJ

DRIVER’SA-PILLAR


SHOP TOWEL

QD40304BJ

DRIVER’SA-PILLARTRIM

DRIVER’S A-PILLARTRIM

UPPERCLIP

6 of 14 AII01797-2

9. Remove the remaining upper clip from the driver’s A-pillar.

10. Install the new clip (supplied) to the driver’s A-pillartrim.Go to step 12.

QD40305BJ

Pushtwo tabs.

UPPER CLIP(Discard.)

DRIVER’SA-PILLAR

QC72508AJ


CLIP(supplied)


Without side curtain airbags
11. Pull away the door opening seal, and remove thedriver’s A-pillar trim (three clips).

12. Pull away the door opening seal, and remove thedriver’s dashboard side lid (six retaining tabs).

QD40366BJ



3 CLIPS

QD40315AJ

DRIVER’SDASHBOARD SIDE LID

PLASTICTRIM TOOL


6 RETAININGTABS


13. Attach the tape to the lower column cover.

14. Pull away the door opening seal, and remove thedriver’s dashboard lower cover (12 clips, and unplugthe vehicle connectors).

QD40316AJTAPELOWER COLUMNCOVER

QD40317AJ11 CLIPSDRIVER’S DASHBOARDLOWER COVER

CLIPVEHICLECONNECTORS

DOOR OPENING SEAL(Pull away.)

3 (1504) 7 of 14

15. Pull away the door opening seal, and remove the
driver’s front door sill trim (one clip and six retainingtabs).

16. Pull away the door opening seal, and remove thedriver’s kick panel (two clips).

QD40319AJ

3 RETAININGTABS

3 RETAININGTABS

CLIPDRIVER’S FRONTDOOR SILL TRIM

DOOR OPENINGSEAL(Pull away.)

QD40320AJ

DOOR OPENINGSEAL(Pull away.)

DRIVER’SKICK PANEL

2 CLIPS

8 of 14 AII01797-2

17. Using isopropyl alcohol on a shop towel, clean thevehicle panel where the urethane tape will attach.

18. Using scissors, cut one urethane tape in half. Attachone half of urethane tape to the vehicle panel asshown. Be careful not to crease the headliner.

QD42306AJ

HALF OFURETHANETAPE

VEHICLE PANEL(Clean withisopropyl alcohol.)

SECTION VIEW

VEHICLEPANEL

Align the centerof urethane tapewith the center ofthe mirror mount.

MIRRORMOUNT

URETHANE TAPE(Cut in half.)

HEADLINER

HALF OFURETHANETAPE

FRONT


19. Install the automatic day/night mirror on the mirror
mount as shown, and tighten the TORX screw.

20. Using isopropyl alcohol on a shop towel, clean thefuse case where the fuse label will attach.

21. Attach the fuse label to the automatic day/nightmirror harness fuse case.

QD42307AJ

MIRRORMOUNT


TORX SCREWTorque: 1.55 - 2.05 N·m(0.16 - 0.21 kgf·m,1.14 - 1.51 lbf·ft).

QD42308AJ

AUTOMATICDAY/NIGHTMIRRORHARNESS

FUSE LABEL(2A OPTION)

FUSE CASE(Clean withisopropyl alcohol.)


22. Using a white marker, mark the automatic day/nightmirror harness at the measurement shown.

WHITE MARKER

MARK

205 mm(8.1 in.)

AUTOMATIC DAY/NIGHTMIRROR HARNESS

3 (1504) 9 of 14

23. Plug the automatic day/night mirror harness 7-pin
connector into the automatic day/night mirror.

24. Gentry pull back the headliner, and tuck theautomatic day/night mirror harness behind theheadliner. Align the mark on the automatic day/nightmirror harness with the edge of the headliner. Becareful not to crease the headliner.


HEADLINER

AUTOMATICDAY/NIGHTMIRRORHARNESS7-PINCONNECTOR

AUTOMATIC DAY/NIGHT

SECTIONVIEW

FRONT


VEHICLEPANEL

SECTIONVIEW

FRONT

MARK(Align with theedge of the headliner.)

VEHICLEPANEL

AUTOMATICDAY/NIGHTMIRROR

10 of 14 AII01797-2

25. Route the automatic day/night mirror harnessthrough the groove in the harness cover. Secure theharness cover to the mirror stay. Slide the harnesscover behind the headliner.

26. Route the automatic day/night mirror harness downthe A-pillar as shown. Align the green tape on theautomatic day/night mirror harness with the vehicleclip, and secure the automatic day/night mirrorharness to the vehicle harness with two wire ties. Donot cover the installation holes of the driver’s A-pillartrim.

QD42310AJAUTOMATIC DAY/NIGHTMIRROR


HARNESS COVER

HARNESSCOVER

AUTOMATIC DAY/NIGHT MIRROR

QD42311AJ

GREENTAPE

2 WIRETIES

WIRE TIE

SECTIONVIEW

VEHICLEPANEL

VEHICLEHARNESS


VEHICLECLIP


VEHICLEHARNESS


27. Align the green tape on the automatic day/night
mirror harness with the vehicle clip, and secure theautomatic day/night mirror harness to the vehicleharness with one wire tie.

28. Using isopropyl alcohol on a shop towel, clean thedriver’s A-pillar where the aluminum tape will attach.

29. Attach the green tape on the automatic day/nightmirror harness to the driver’s A-pillar with onealuminum tape.

QD42312AJ

GREENTAPE

WIRE TIE

WIRE TIE

SECTIONVIEW VEHICLE

PANEL

VEHICLEHARNESS


VEHICLE HARNESS


VEHICLECLIP

QD42313AJGREEN TAPE

DRIVER’SA-PILLAR


ALUMINUMTAPE

Clean withisopropylalcohol.


30. Pull away the door opening seal. Route theautomatic day/night mirror harness down next to thedashboard, and tuck the automatic day/night mirrorharness between the driver’s A-pillar and thedashboard.

Without Other Accessory Harness 8-pin Connector

31. Plug the automatic day/night mirror harness 8-pinconnector into the fuse box. Go to step 33.

QD42314AJ

DOOR OPENING SEAL(Pull away.) DASHBOARD

DRIVER’SA-PILLAR


QD42315AJ

AUTOMATIC DAY/NIGHTMIRROR HARNESS8-PIN CONNECTOR

FUSE BOXFRONT VIEW

Plug inhere.

3 (1504) 11 of 14

With Other Accessory Harness 8-pin Connector
32. If other accessory harness 8-pin connector isplugged into the fuse box, unplug the 8-pinconnector from the fuse box, then plug the automaticday/night mirror harness 8-pin connector into thefuse box. Remove and discard the dummy connectorfrom the automatic day/night mirror harness 8-pinconnector, and plug other accessory harness 8-pinconnector into the automatic day/night mirrorharness 8-pin connector.

QD42316AJ

AUTOMATIC DAY/NIGHTMIRROR HARNESS8-PIN CONNECTORS

FUSEBOX

FRONT VIEW

Plug inhere.

OTHERACCESSORYHARNESS8-PINCONNECTOR

DUMMYCONNECTOR(Discard.)

12 of 14 AII01797-2

33. Secure the 8-pin connectors and automatic day/night mirror harness to the vehicle harness withthree wire ties.

34. Route the automatic day/night mirror harness alongthe vehicle harness. Remove the bolt, and install theautomatic day/night mirror harness ground terminalwith one ground bolt.

QD42317AJ

8-PINCONNECTORS


VEHICLEHARNESS 3 WIRE TIES

QD42318AJ

HOODOPENER

BOLT(Discard.)

GROUND BOLT

AUTOMATIC DAY/NIGHT MIRRORHARNESS GROUND

VEHICLEHARNESS


35. Secure the automatic day/night mirror harness to the
vehicle harness with two wire ties.

36. Check that all wire harnesses are routed properlyand all connectors are plugged in.

37. Check the overlap between the headliner and thedriver’s A-pillar trim. Refer to the Service Manual. Ifnecessary, adjust the overlap.

38. Reinstall all removed parts.

39. Reconnect the negative cable to the battery.

40. Press and hold the radio power button for twoseconds to restore the radio and navi (if equipped)system functions.

41. Reset the clock.

42. Restore the systems back to normal operation asdescribed in the Service Manual if necessary.

43. Perform the “CHECK THE OPERATION OF THEAUTOMATIC DAY/NIGHT MIRROR.”

44. Adjust the zone and calibrate as required.

QD42319AJ


VEHICLEHARNESS

2 WIRE TIES


CHECK THE OPERATION OF THE AUTOMATIC DAY/NIGHT MIRROR

1. Turn the engine switch to ON, but do not start theengine.

2. Turn on the switch. Check that the LED lights.

030406AB

SWITCH(Turn on.)

LED



3 (1504) 13 of 14

3. Cover the front sensor on the automatic day/night
mirror with your hand, and use a flashlight to light therear sensor on the automatic day/night mirror. Makesure the mirror surface dims.

4. Step on the brake pedal, and move the shift lever tothe R position. Repeat step 3, and make sure themirror surface does not dim.

• Make sure that the parking brake is set securely.

• If the automatic day/night mirror does notfunction properly, check the fuse and allconnectors, including the ground cable.

030407AB

FRONT SENSOR(Cover.)FLASHLIGHT


MIRRORSURFACE

REARSENSOR

14 of 14 AII01797-2

Documents

· 23. Plug the automatic day/night mirror harness 7-pin connector into the automatic day/night mirror. 24. Gentry pull back the headliner, and tuck the automatic day/night mirror