Publications No.
INSTALLATIONINSTRUCTIONS
Accessory Application
© 2015 American Honda Motor Co., Inc. – All Rights Re
VERSION 1
www.collegehillshonda.com
AUTOMATIC DAY/NIGHTMIRROR
served. AII01797-23 (150
2016 HR-V
4) 0
Issue Date
APR 2015
PARTS LIST
Attachment KitP/N 08V03-T7S-100
Automatic day/night mirror harness
Harness cover
8 Wire ties
Clip(May not used)
Urethane tape
Fuse label
Ground bolt
Aluminum tape
Automatic Day/Night Mirror KitP/N 08V03-TR0-100A
Automatic day/night mirror
Accessory User’s Information Manual
1 of 148V03-T7S-1000-90
www.collegehillshonda.com
TOOLS AND SUPPLIES REQUIREDPhillips screwdriver
Flat-tip screwdriver
Ratchet
10 mm Socket
Isopropyl alcohol
Shop towel
Diagonal cutters
Torque wrench
T20 TORX bit
Flashlight
Tape
10 mm Open end wrench
Scissors
White marker
Ruler
The following tools are available through the Honda Tooland Equipment Program. On the iN, click on: Service >Service Bay > Tool and Equipment Program, then enterthe number under “Search”. Or, call 888-424-6857.
• Trim Tool Set (T/N SOJATP2014)
• Plastic Trim Tool (T/N SILTRIMTL10)
Illustration of the Automatic Day/Night Mirror in theVehicle
QD42301AJ
AUTOMATIC DAY/NIGHTMIRROR
2A FUSE
AUTOMATIC DAY/NIGHTMIRROR
2 of 14 AII01797-2
INSTALLATION
1. Disconnect the negative cable from the battery.
2. Loosen the TORX screw, and remove the rearviewmirror from the mirror mount.
Customer Information: The information in thisinstallation instruction is intended for use only by skilledtechnicians who have the proper tools, equipment, andtraining to correctly and safely add equipment to yourvehicle. These procedures should not be attempted by“do-it-yourselfers.”
QD42302BJ
TORX SCREW(Loosen.)
MIRRORMOUNT
REARVIEW MIRROR(Discard.)
3 (1504) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
3. Remove the left and right lenses from the map lightconsole (four retaining tabs for each lens). Removethe two bolts.
With Moonroof: Remove the map light console. Thenunplug the vehicle connectors, and remove theswitch (four retaining tabs).
Without Moonroof: Remove the map light console(unplug the vehicle connector).
QD42303AJLEFT MAPLIGHT LENS
4 RETAININGTABS
2 BOLTS
MAP LIGHTCONSOLE
4 RETAININGTABS
RIGHT MAPLIGHT LENS
SWITCH
VEHICLECONNECTORS
4 RETAININGTABS
QD42304AJLEFT MAPLIGHT LENS
4 RETAININGTABS
2 BOLTS
MAP LIGHTCONSOLE
4 RETAININGTABS
RIGHT MAPLIGHT LENS
VEHICLECONNECTOR
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII01797-2
4. Release the passenger’s sunvisor from thepassenger’s sunvisor holder.
5. Remove the passenger’s sunvisor holder:
• Wrap tape around the tip of flat-tip screwdriver.
• Release three retaining tabs on the passenger’ssunvisor holder.
QD42305AJ
PASSENGER’SSUNVISOR
PASSENGER’SSUNVISOR HOLDER
QC22003BJ
PASSENGER’SSUNVISOR HOLDER
FLAT-TIPSCREWDRIVER
TAPE
3 RETAININGTABS(Push.)
3 (1504) 3 of 14
www.collegehillshonda.com
• While holding down the passenger’s sunvisorholder as shown, use a flat-tip screwdriverwrapped with a tape to remove the passenger’ssunvisor holder (three retaining tabs).
QC22004AJ
3 RETAININGTABS(Push.)
Hold down.
PASSENGER’SSUNVISOR HOLDER
FLAT-TIPSCREWDRIVER
4 of 14 AII01797-2
6. Remove the driver’s sunvisor (unplug the vehicleconnector):
• Pivot the driver’s sunvisor downward.
• Wrap tape around the tip of flat-tip screwdriver.
• Locate the slot in the base cover, and insert theflat-tip screwdriver into the slot. Push in and holdthe retaining tab.
• While holding the retaining tab, push up on thesunvisor and rotate it toward the door.NOTE: If the retaining tab does not stay pushedin, return the sunvisor to its original position andrepeat this step.
QD40301AJPush theretaining tab.
While pushing inon the tab, rotatethe sunvisortoward the door.
Make sure thetab slides intothe base cover.DRIVER’S
SUNVISOR
BASECOVERFLAT-TIP
SCREWDRIVER
TAPE
RETAININGTAB
FRONT
VEHICLECONNECTOR(if equipped)
3 (1504) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
7. Remove the driver’s sunvisor holder:• Wrap tape around the tip of flat-tip screwdriver.
• Release three retaining tabs on the driver’ssunvisor holder.
• While holding down the driver’s sunvisor holderas shown, use a flat-tip screwdriver wrappedwith a tape to remove the driver’s sunvisorholder (three retaining tabs).
QC22003BJ
DRIVER’SSUNVISOR HOLDER
FLAT-TIPSCREWDRIVER
TAPE
3 RETAININGTABS(Push.)
QC22004AJ
3 RETAININGTABS(Push.)
Hold down.
DRIVER’SSUNVISOR HOLDER
FLAT-TIPSCREWDRIVER
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII01797-2
If the vehicle is equipped with the side curtain airbags,continue with step 8. If not, go to step 11.
With side curtain airbags
8. Remove the driver’s A-pillar trim:
• Pull away the door opening seal from the driver’sA-pillar trim.
• Pull out on the driver’s A-pillar trim to releasethree clips.
QD40302BJ
Pullthe clip.
2 CLIPS
DRIVER’SA-PILLARTRIM
DRIVER’S A-PILLAR
DOOROPENINGSEAL(Pull away.)
DRIVER’SA-PILLAR TRIM
SECTION VIEW
3 (1504) 5 of 14
www.collegehillshonda.com
• To prevent clips from falling into the body panelarea, carefully insert a shop towel between thedriver’s A-pillar and the driver’s A-pillar trim.
• Slide the driver’s A-pillar trim upward, andremove the driver’s A-pillar trim.
• Remove the shop towel and any clips.
QD40303BJ
DRIVER’SA-PILLAR
DRIVER’SA-PILLAR TRIM
SHOP TOWEL
QD40304BJ
DRIVER’SA-PILLARTRIM
DRIVER’S A-PILLARTRIM
UPPERCLIP
6 of 14 AII01797-2
9. Remove the remaining upper clip from the driver’s A-pillar.
10. Install the new clip (supplied) to the driver’s A-pillartrim.Go to step 12.
QD40305BJ
Pushtwo tabs.
UPPER CLIP(Discard.)
DRIVER’SA-PILLAR
QC72508AJ
DRIVER’SA-PILLAR TRIM
CLIP(supplied)
3 (1504) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
Without side curtain airbags11. Pull away the door opening seal, and remove thedriver’s A-pillar trim (three clips).
12. Pull away the door opening seal, and remove thedriver’s dashboard side lid (six retaining tabs).
QD40366BJ
DOOROPENINGSEAL(Pull away.)
DRIVER’SA-PILLAR TRIM
3 CLIPS
QD40315AJ
DRIVER’SDASHBOARD SIDE LID
PLASTICTRIM TOOL
DOOROPENINGSEAL(Pull away.)
6 RETAININGTABS
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII01797-2
13. Attach the tape to the lower column cover.
14. Pull away the door opening seal, and remove thedriver’s dashboard lower cover (12 clips, and unplugthe vehicle connectors).
QD40316AJTAPELOWER COLUMNCOVER
QD40317AJ11 CLIPSDRIVER’S DASHBOARDLOWER COVER
CLIPVEHICLECONNECTORS
DOOR OPENING SEAL(Pull away.)
3 (1504) 7 of 14
www.collegehillshonda.com
15. Pull away the door opening seal, and remove thedriver’s front door sill trim (one clip and six retainingtabs).
16. Pull away the door opening seal, and remove thedriver’s kick panel (two clips).
QD40319AJ
3 RETAININGTABS
3 RETAININGTABS
CLIPDRIVER’S FRONTDOOR SILL TRIM
DOOR OPENINGSEAL(Pull away.)
QD40320AJ
DOOR OPENINGSEAL(Pull away.)
DRIVER’SKICK PANEL
2 CLIPS
8 of 14 AII01797-2
17. Using isopropyl alcohol on a shop towel, clean thevehicle panel where the urethane tape will attach.
18. Using scissors, cut one urethane tape in half. Attachone half of urethane tape to the vehicle panel asshown. Be careful not to crease the headliner.
QD42306AJ
HALF OFURETHANETAPE
VEHICLE PANEL(Clean withisopropyl alcohol.)
SECTION VIEW
VEHICLEPANEL
Align the centerof urethane tapewith the center ofthe mirror mount.
MIRRORMOUNT
URETHANE TAPE(Cut in half.)
HEADLINER
HALF OFURETHANETAPE
FRONT
3 (1504) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
19. Install the automatic day/night mirror on the mirrormount as shown, and tighten the TORX screw.
20. Using isopropyl alcohol on a shop towel, clean thefuse case where the fuse label will attach.
21. Attach the fuse label to the automatic day/nightmirror harness fuse case.
QD42307AJ
MIRRORMOUNT
AUTOMATIC DAY/NIGHTMIRROR
TORX SCREWTorque: 1.55 - 2.05 N·m(0.16 - 0.21 kgf·m,1.14 - 1.51 lbf·ft).
QD42308AJ
AUTOMATICDAY/NIGHTMIRRORHARNESS
FUSE LABEL(2A OPTION)
FUSE CASE(Clean withisopropyl alcohol.)
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII01797-2
22. Using a white marker, mark the automatic day/nightmirror harness at the measurement shown.
WHITE MARKER
MARK
205 mm(8.1 in.)
AUTOMATIC DAY/NIGHTMIRROR HARNESS
3 (1504) 9 of 14
www.collegehillshonda.com
23. Plug the automatic day/night mirror harness 7-pinconnector into the automatic day/night mirror.
24. Gentry pull back the headliner, and tuck theautomatic day/night mirror harness behind theheadliner. Align the mark on the automatic day/nightmirror harness with the edge of the headliner. Becareful not to crease the headliner.
AUTOMATIC DAY/NIGHTMIRROR
HEADLINER
AUTOMATICDAY/NIGHTMIRRORHARNESS7-PINCONNECTOR
AUTOMATIC DAY/NIGHT
SECTIONVIEW
FRONT
AUTOMATIC DAY/NIGHTMIRROR HARNESS
VEHICLEPANEL
SECTIONVIEW
FRONT
MARK(Align with theedge of the headliner.)
VEHICLEPANEL
AUTOMATICDAY/NIGHTMIRROR
10 of 14 AII01797-2
25. Route the automatic day/night mirror harnessthrough the groove in the harness cover. Secure theharness cover to the mirror stay. Slide the harnesscover behind the headliner.
26. Route the automatic day/night mirror harness downthe A-pillar as shown. Align the green tape on theautomatic day/night mirror harness with the vehicleclip, and secure the automatic day/night mirrorharness to the vehicle harness with two wire ties. Donot cover the installation holes of the driver’s A-pillartrim.
QD42310AJAUTOMATIC DAY/NIGHTMIRROR
AUTOMATIC DAY/NIGHTMIRROR
HARNESS COVER
HARNESSCOVER
AUTOMATIC DAY/NIGHT MIRROR
QD42311AJ
GREENTAPE
2 WIRETIES
WIRE TIE
SECTIONVIEW
VEHICLEPANEL
VEHICLEHARNESS
AUTOMATIC DAY/NIGHTMIRROR
VEHICLECLIP
AUTOMATIC DAY/NIGHTMIRROR HARNESS
VEHICLEHARNESS
3 (1504) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
27. Align the green tape on the automatic day/nightmirror harness with the vehicle clip, and secure theautomatic day/night mirror harness to the vehicleharness with one wire tie.
28. Using isopropyl alcohol on a shop towel, clean thedriver’s A-pillar where the aluminum tape will attach.
29. Attach the green tape on the automatic day/nightmirror harness to the driver’s A-pillar with onealuminum tape.
QD42312AJ
GREENTAPE
WIRE TIE
WIRE TIE
SECTIONVIEW VEHICLE
PANEL
VEHICLEHARNESS
AUTOMATIC DAY/NIGHTMIRROR
VEHICLE HARNESS
AUTOMATIC DAY/NIGHTMIRROR
VEHICLECLIP
QD42313AJGREEN TAPE
DRIVER’SA-PILLAR
AUTOMATIC DAY/NIGHTMIRROR
ALUMINUMTAPE
Clean withisopropylalcohol.
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII01797-2
30. Pull away the door opening seal. Route theautomatic day/night mirror harness down next to thedashboard, and tuck the automatic day/night mirrorharness between the driver’s A-pillar and thedashboard.
Without Other Accessory Harness 8-pin Connector
31. Plug the automatic day/night mirror harness 8-pinconnector into the fuse box. Go to step 33.
QD42314AJ
DOOR OPENING SEAL(Pull away.) DASHBOARD
DRIVER’SA-PILLAR
AUTOMATIC DAY/NIGHTMIRROR HARNESS
QD42315AJ
AUTOMATIC DAY/NIGHTMIRROR HARNESS8-PIN CONNECTOR
FUSE BOXFRONT VIEW
Plug inhere.
3 (1504) 11 of 14
www.collegehillshonda.com
With Other Accessory Harness 8-pin Connector32. If other accessory harness 8-pin connector isplugged into the fuse box, unplug the 8-pinconnector from the fuse box, then plug the automaticday/night mirror harness 8-pin connector into thefuse box. Remove and discard the dummy connectorfrom the automatic day/night mirror harness 8-pinconnector, and plug other accessory harness 8-pinconnector into the automatic day/night mirrorharness 8-pin connector.
QD42316AJ
AUTOMATIC DAY/NIGHTMIRROR HARNESS8-PIN CONNECTORS
FUSEBOX
FRONT VIEW
Plug inhere.
OTHERACCESSORYHARNESS8-PINCONNECTOR
DUMMYCONNECTOR(Discard.)
12 of 14 AII01797-2
33. Secure the 8-pin connectors and automatic day/night mirror harness to the vehicle harness withthree wire ties.
34. Route the automatic day/night mirror harness alongthe vehicle harness. Remove the bolt, and install theautomatic day/night mirror harness ground terminalwith one ground bolt.
QD42317AJ
8-PINCONNECTORS
AUTOMATIC DAY/NIGHTMIRROR HARNESS
VEHICLEHARNESS 3 WIRE TIES
QD42318AJ
HOODOPENER
BOLT(Discard.)
GROUND BOLT
AUTOMATIC DAY/NIGHT MIRRORHARNESS GROUND
VEHICLEHARNESS
3 (1504) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
35. Secure the automatic day/night mirror harness to thevehicle harness with two wire ties.
36. Check that all wire harnesses are routed properlyand all connectors are plugged in.
37. Check the overlap between the headliner and thedriver’s A-pillar trim. Refer to the Service Manual. Ifnecessary, adjust the overlap.
38. Reinstall all removed parts.
39. Reconnect the negative cable to the battery.
40. Press and hold the radio power button for twoseconds to restore the radio and navi (if equipped)system functions.
41. Reset the clock.
42. Restore the systems back to normal operation asdescribed in the Service Manual if necessary.
43. Perform the “CHECK THE OPERATION OF THEAUTOMATIC DAY/NIGHT MIRROR.”
44. Adjust the zone and calibrate as required.
QD42319AJ
AUTOMATIC DAY/NIGHTMIRROR HARNESS
VEHICLEHARNESS
2 WIRE TIES
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII01797-2
CHECK THE OPERATION OF THE AUTOMATIC DAY/NIGHT MIRROR
1. Turn the engine switch to ON, but do not start theengine.
2. Turn on the switch. Check that the LED lights.
030406AB
SWITCH(Turn on.)
LED
AUTOMATIC DAY/NIGHT MIRROR
AUTOMATIC DAY/NIGHT MIRROR
3 (1504) 13 of 14
www.collegehillshonda.com
3. Cover the front sensor on the automatic day/nightmirror with your hand, and use a flashlight to light therear sensor on the automatic day/night mirror. Makesure the mirror surface dims.
4. Step on the brake pedal, and move the shift lever tothe R position. Repeat step 3, and make sure themirror surface does not dim.
• Make sure that the parking brake is set securely.
• If the automatic day/night mirror does notfunction properly, check the fuse and allconnectors, including the ground cable.
030407AB
FRONT SENSOR(Cover.)FLASHLIGHT
AUTOMATIC DAY/NIGHT MIRROR
MIRRORSURFACE
REARSENSOR
14 of 14 AII01797-2
3 (1504) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.