Upload
others
View
11
Download
0
Embed Size (px)
Citation preview
IOWA MOLD TOOLING CO., INC.
P.O. Box 189Garner, IA 50438Tel: 641.923.3711
Fax: 641.923.2424www.imt.com
26/180Technical
Specifications
Manual # 99904617
Revised 08-07-2017
Copyright © 2017 Iowa Mold Tooling Co., Inc.All rights reserved
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise without the prior written permission of Iowa Mold Tooling Co., Inc.
Iowa Mold Tooling Co., Inc. is an Oshkosh Corporation Company
ii
26/180 - Manual # 99904617
iii
26/180 - Manual # 99904617
Table of Contents
Section - 1 1
26/180SL Specifications.................................................................................................................................226/180SL Specifications - Continued .............................................................................................................326/180SL Specifications - Continued .............................................................................................................426/180SL Metric Specifications ......................................................................................................................526/180SL Metric Specifications - Continued ..................................................................................................626/180SL Metric Specifications - Continued ..................................................................................................7
Section - 2 9
26/180SL Lifting Capacity Chart, K2 ............................................................................................................1026/180SL Lifting Capacity Chart, K3 ............................................................................................................ 1126/180SL Lifting Capacity Chart, K4 ............................................................................................................1226/180SL Lifting Capacity Chart, K5 ............................................................................................................1326/180SL Lifting Capacity Chart, K6 ............................................................................................................1426/180SL Lifting Capacity Chart, K7 ............................................................................................................1526/180SL Lifting Capacity Chart, K8 ............................................................................................................1626/180SL Lifting Capacity K2 - K8 ...............................................................................................................17
Section - 3 19
26/180SL - Pressure setting diagram, fixed flow pump & Danfoss RC ........................................................2026/180SL - Pressure setting diagram, variable flow pump & Danfoss RC ...................................................21Hydraulic Diagram - Danfoss, single-circuit fixed 6 fcts. RC (2 EXV: Grab + Rotator) ..............................................................................................................22Hydraulic Diagram - Danfoss, single-circuit variable 6 fcts. RC/HS dir. valve contr. (2 EXV: Grab + Rotator) ...............................................................................23Hydraulic Diagram - Stabilizer circuit – 2 fcts. .............................................................................................24Hydraulic Diagram - Stabilizer circuit – 4 fcts. .............................................................................................25Hydraulic Diagram - Stabilizer circuit – 4 fcts. RC .......................................................................................26Hydraulic Diagram - Stabilizer circuit – 4 fcts. + 4 available fcts..................................................................27Hydraulic Diagram - Stabilizer circuit – 4 fcts. + 4 available fcts. RC ..........................................................28
Section - 4 31
26/180DL Specifications ..............................................................................................................................3226/180DL Specifications - Continued ...........................................................................................................3326/180DL Specifications - Continued ...........................................................................................................3426/180DL Metric Specifications ....................................................................................................................3526/180DL Metric Specifications - Continued ................................................................................................3626/180DL Metric Specifications - Continued ................................................................................................37
Section - 5 39
26/180DL Lifting Capacity Chart, K2 ............................................................................................................4026/180DL Lifting Capacity Chart, K3 ............................................................................................................4126/180DL Lifting Capacity Chart, K4 ............................................................................................................4226/180DL Lifting Capacity Chart, K5 ............................................................................................................4326/180DL Lifting Capacity Chart, K6 ............................................................................................................4426/180DL Lifting Capacity Chart, K7 ............................................................................................................4526/180DL Lifting Capacity Chart, K8 ............................................................................................................4626/180DL Lifting Capacity K2 - K8 ...............................................................................................................47
iv
26/180 - Manual # 99904617
Section - 6 49
26/180DL - Pressure setting diagram, fixed flow pump & Danfoss RC........................................................5026/180DL - Pressure setting diagram, variable flow pump & Danfoss RC...................................................51Hydraulic Diagram - Danfoss, single-circuit fixed 6 fcts. RC (2 EXV: Grab + Rotator) ..............................................................................................................52Hydraulic Diagram - Danfoss, single-circuit variable 7 fcts. RC (3 EXV: FJ + 2 EXV, winch) .........................................................................................................53Hydraulic Diagram - Danfoss, single-circuit variable 6 fcts. RC/HS dir. valve contr. (2 EXV: Grab + Rotator) ...............................................................................54Hydraulic Diagram - Danfoss, single-circuit variable 7 fcts. RC (3 EXV: FJ + 2 EXV, winch) .........................................................................................................55Hydraulic Diagram - Stabilizer circuit – 2 fcts. .............................................................................................56Hydraulic Diagram - Stabilizer circuit – 4 fcts. .............................................................................................57Hydraulic Diagram - Stabilizer circuit – 4 fcts. RC .......................................................................................58Hydraulic Diagram - Stabilizer circuit – 4 fcts. + 4 available fcts..................................................................59Hydraulic Diagram - Stabilizer circuit – 4 fcts. + 4 available fcts. RC ..........................................................60
Section - 7 63
Lifting capacity with winch ............................................................................................................................6420/180SL - Dimension sketch ......................................................................................................................6520/180DL - Dimension sketch ......................................................................................................................6620/180SL - Slewing Radius ..........................................................................................................................6720/180DL - Slewing Radius..........................................................................................................................68Dimension sketch for truck-mounted loader ................................................................................................6920/180SL - Lifting height at column..............................................................................................................7020/180DL - Lifting height at column .............................................................................................................71Dimension sketch, fixed stabilizer legs ........................................................................................................72Dimension sketch, fixed stabilizer legs ........................................................................................................73Dimension sketch, swing-up stabilizer legs 20°- 60° (manual) ....................................................................74Dimension sketch, swing-up stabilizer legs 20°- 60° (manual) ....................................................................75Dimension sketch, swing-up stabilizer legs 180° (manual + hydraulic) .......................................................76Dimension sketch, swing-up stabilizer legs 180° (manual + hydraulic) .......................................................77Dimension sketch, TS - Top seat (RC) .........................................................................................................78Dimension sketch, TS - Top seat (HC linear) ...............................................................................................79Dimension sketch, TS - Top seat (Danfoss X) .............................................................................................80Dimension sketch, TS - Top seat (HC X) .....................................................................................................81Dimension sketch, ladder for TS ..................................................................................................................82Technical data, winch ...................................................................................................................................83Dimension sketch, winch .............................................................................................................................84Dimension sketch, stand-up platform (std.) .................................................................................................85Dimension sketch, stand-up platform (valve control) ...................................................................................86Dimension sketch, internal hose routing ......................................................................................................87Dimension sketch, extra valves K7, K8 ........................................................................................................88Stowed in truck body ....................................................................................................................................8920/180SL Center of Gravity ..........................................................................................................................9020/180DL Center of Gravity .........................................................................................................................91
This page left intentionally blank
v
26/180 - Manual # 99904617
This page left intentionally blank
vi
26/180 - Manual # 99904617
Section - 1 1 26/180SL Technical Specifications
26/180 - Manual # 99904617
Section - 126/180SL Technical Specifications
Section - 1 2 26/180SL Technical Specifications
26/180 - Manual # 99904617
26/180SL Specifications
Performance Unit K2 K3 K4 K5 K6 K7 K8Loading group (EN12999) H1/B3 H1/B3 H1/B3 H1/B3 H1/B3 H1/B3 H1/B3
Load moment ft-lb 174680 170349 166740 163853 159522 158078 154469Hydraulic reach ft 27’2’’ 33’8’’ 41’0’’ 48’6’’ 56’1’’ 63’4’’ 70’10’’Hydraulic telescopic movement ft 12’6” 19’1” 26’ 33’2” 40’7” 47’7” 54’10”
Lifting capacity, hydraulic
lb-ft 12300 - 14’1’’
11815 - 14’5’’
11350 - 14’9’’
10960 - 15’1’’
10540 - 15’1’’
10230 - 15’5’’
9855 - 15’9’’
8490 - 20’4’’
8090 - 20’8’’ 7695 - 21’ 7365 - 21’ 7010 -
21’4’’6770 - 21’7’’ 6460 - 22’
6440 - 26’11’’
6065 - 26’11’’
5710 - 27’2’’
5380 - 27’6’’
5070 - 27’10’’
4830 - 27’10’’
4565 - 28’3’’
4850 - 33’5’’
4450 - 33’9’’
4190 - 34’1’’
3880 - 34’5’’
3660 - 34’5’’
3395 - 34’89’
3705 - 40’8’’
3395 - 41’1’’
3090 - 41’4’’
2865 - 41’4’’
2625 - 41’8’’
2845 - 48’2’’
2560 - 48’6’’
2340 - 48’7’’
2095 - 48’11’’
2180 - 55’9’’
1985 - 56’1’’
1740 - 56’5’’
1740 - 63’ 1520 - 63’4’’1345 - 70’6’’
Lifting capacity, manual extensions
lb-ft 2954 - 48’3’’
2205 - 56’1’’
1598 - 63’8’’
1157 - 70’10’’
705 - 78’5’’
2315 - 56’1’’
1763 - 63’8’’
1157 - 71’2’’ 705 - 78’5’’
1819 - 63’8’’
1157 - 71’2’’ 705 - 79’0’’
Slewing torque, gross lbft 19987 19987 19987 19987 19987 19987 19987
Slewing angle ° 400 400 400 400 400 400 400Max. heel at max. load moment ° 5 5 5 5 5 5 5
Slewing speed °/s 24 24 24 24 24 24 24
Minimum Chassis SpecsFront Axle Rating (GAWR) 14,000 lbs (6,50 kg)Rear Axle Rating (GAWR) 40,000 lbs (18,150 kg)Resistance to Bending Moment 2,700,000 in-lbs (373,300 kg-m)
Section - 1 3 26/180SL Technical Specifications
26/180 - Manual # 99904617
26/180SL Specifications - Continued
Dimensions Unit K2 K3 K4 K5 K6 K7 K8Height above chassis in 90 90 90 90 90 90 91Width in 98 98 98 98 98 98 98Length, no extra valves in 34 34 34 34 34 39 39Length, with extra valves (hose guides) in 39 39 39 39 39
Length, with 1 extra valve (hose reels) in 39 39
Length, with 2 extra valves (hose reels) in 40 40
Length, with extra valves (int. hose routing) in 34 34 34 34 34
Stabilizer spread, S1 (standard) ft 18’3” 18’3” 18’3” 18’3” 18’3” 18’3” 18’3”
Stabilizer spread, D ft 21’2” 21’2” 21’2” 21’2” 21’2” 21’2” 21’2”
Weights, basic loader Unit K2 K3 K4 K5 K6 K7 K8Standard loader 1), excl. stabilizers lbs 3902 4244 4586 4894 5170 5401 5589
Stabilizers, S1 fixed lbs 606 606 606 606 606 606 606Stabilizers, S1 swing-up lbs 617 617 617 617 617 617 617Stabilizers, S1 hydr. swing-up lbs 628 628 628 628 628 628 628
Stabilizers, D fixed lbs 783 783 783 783 783 783 783Stabilizers, D swing-up lbs 783 783 783 783 783 783 783Stabilizers, D hydr. swing-up lbs 805 805 805 805 805 805 805Mounting kit, 4 bolts lbs 143 143 143 143 143 143 143Mounting kit, 8 bolts lbs 132 132 132 132 132 132 132Tank, excl. oil (fitted on loader) lbs 99 99 99 99 99 99 99
Manual extensions lbs 176 154 132 99 77lbs 154 132 99 77lbs 132 99 77
Oil in loader (stowing position) lbs 77 88 99 110 121 132 143
1) Weights ± 5% because of tolerances for plate thickness
Section - 1 4 26/180SL Technical Specifications
26/180 - Manual # 99904617
26/180SL Specifications - Continued
Weights, equipment Unit K2 K3 K4 K5 K6 K7 K8Stand-up controls (HS), std. lbs 132 132 132 132 132 132 132Stand-up controls (HS), direct valve control lbs 154 154 154 154 154 154 154
Top seat (TS) lbs 198 198 198 198 198 198 198Top seat, ladder lbs 44 44 44 44 44 44 441 extra valve, hose guides lbs 121 143 165 187 2091 extra valve, hose reels lbs 209 2091 extra valve, int. hose routing lbs 165 165 176 176 1872 extra valves, hose guides lbs 165 198 231 265 2982 extra valves, hose reels lbs 408 4082 extra valves, int. hose routing lbs 287 287 309 320 331Winch (1.5 t), single snatch block lbs 386 386 386 386 397 397 419
Winch (1.5 t), double snatch block lbs 375 375 375 375 386 386 397
Winch (2.5 t), single snatch block lbs 441 441 441 441 452 452 463
Winch (2.5 t), double snatch block lbs 430 430 430 430 441 441 452
High-pressure filter lbs 15 15 15 15 15 15 15
Oil cooler lbs 55 55 55 55 55 55 55
Max. Load on stabilizers (per stabilizer cylinder) Unit K2 K3 K4 K5 K6 K7 K8
S1, fixed Lbf 26 26 26 26 26 26 26S1, swing-up Lbf 26 26 26 26 26 26 26S1, hydr. swing-up Lbf 26 26 26 26 26 26 26D, fixed Lbf 22 22 22 22 22 22 22D, swing-up Lbf 22 22 22 22 22 22 22D, hydr. swing-up Lbf 22 22 22 22 22 22 22
Power consumption(oil capacity) Unit K2 K3 K4 K5 K6 K7 K8
Working pressure PSI 5003 5003 5003 5003 5003 5003 5003
Tank capacity (fitted on loader) Gal 23 23 23 23 23 23 23Max. pump performance, Hydrocontrol, 1-circuit Gpm 15 15 15 15 15 15 15
Max. pump performance, Hydrocontrol, 2-circuit Gpm - - - - - - -
Max. pump performance, Danfoss fixed flow Gpm 18 18 18 18 18 18 18
Max. pump performance, Danfoss variable Gpm 31 31 31 31 31 31 31
Section - 1 5 26/180SL Technical Specifications
26/180 - Manual # 99904617
26/180SL Metric Specifications
Performance Unit K2 K3 K4 K5 K6 K7 K8Loading group (EN12999) H1/B3 H1/B3 H1/B3 H1/B3 H1/B3 H1/B3 H1/B3
Load moment tm 24.2 23.6 23.1 22.7 22.1 21.9 21.4Hydraulic reach m 8.3 10.3 12.5 14.8 17.1 19.3 21.6Hydraulic telescopic movement mm 3830 5840 7930 10130 12370 14520 16720
Lifting capacity. hydraulic kg-m 5580 - 4.3 5360 - 4.4 5150 - 4.5 4970 - 4.6 4780 - 4.6 4640 - 4.7 4470 - 4.8
3850 - 6.2 3670 - 6.3 3490 - 6.4 3340 - 6.4 3180 - 6.5 3070 - 6.6 2930 - 6.7
2920 - 8.2 2750 - 8.2 2590 - 8.3 2440 - 8.4 2300 - 8.5 2190 - 8.5 2070 - 8.6
2200 - 10.2
2040 - 10.3
1900 - 10.4
1760 - 10.5
1660 - 10.5
1540 - 10.6
1680 - 12.4
1540 - 12.5
1400 - 12.6
1300 - 12.6
1190 - 12.7
1290 - 14.7 1160 - 14.8 1060 -
14.8 950 - 14.9
990 - 17.0 900 - 17.1 790 - 17.2
790 - 19.2 690 - 19.3
610 - 21.5
Lifting capacity. manual extensions kg-m 1340 -
14.71000 - 17.1 725 - 19.4 525 - 21.6 320 - 23.9
1050 - 17.1 800 - 19.4 525 - 21.7 320 - 23.9
825 - 19.4 525 - 21.7 320 - 24.1Slewing torque. gross kNm 27.1 27.1 27.1 27.1 27.1 27.1 27.1
Slewing angle ° 400 400 400 400 400 400 400Max. heel at max. load moment ° 5 5 5 5 5 5 5
Slewing speed °/s 24 24 24 24 24 24 24
Section - 1 6 26/180SL Technical Specifications
26/180 - Manual # 99904617
26/180SL Metric Specifications - Continued
Dimensions Unit K2 K3 K4 K5 K6 K7 K8Height above chassis mm 2295 2295 2295 2295 2295 2295 2335Width mm 2500 2500 2500 2500 2500 2500 2500Length, no extra valves mm 885 885 885 885 885 995 995Length, with extra valves (hose guides) mm 1005 1005 1005 1005 1005
Length, with 1 extra valve (hose reels) mm 995 995
Length, with 2 extra valves (hose reels) mm 1030 1030
Length, with extra valves (int. hose routing) mm 885 885 885 885 885
Stabilizer spread, S1 (standard) mm 5575 5575 5575 5575 5575 5575 5575
Stabilizer spread, D mm 6455 6455 6455 6455 6455 6455 6455
Weights, basic loader Unit K2 K3 K4 K5 K6 K7 K8Standard loader 1), excl. stabilizers kg 1770 1925 2080 2220 2345 2450 2535
Stabilizers, S1 fixed kg 275 275 275 275 275 275 275Stabilizers, S1 swing-up kg 280 280 280 280 280 280 280Stabilizers, S1 hydr. swing-up kg 285 285 285 285 285 285 285
Stabilizers, D fixed kg 355 355 355 355 355 355 355Stabilizers, D swing-up kg 355 355 355 355 355 355 355Stabilizers, D hydr. swing-up kg 365 365 365 365 365 365 365Mounting kit, 4 bolts kg 65 65 65 65 65 65 65Mounting kit, 8 bolts kg 60 60 60 60 60 60 60Tank, excl. oil (fitted on loader) kg 45 45 45 45 45 45 45
Manual extensions kg 80 70 60 45 35kg 70 60 45 35kg 60 45 35
Oil in loader (stowing position) kg 35 40 45 50 55 60 65
1) Weights ± 5% because of tolerances for plate thickness
Section - 1 7 26/180SL Technical Specifications
26/180 - Manual # 99904617
26/180SL Metric Specifications - Continued
Weights, equipment Unit K2 K3 K4 K5 K6 K7 K8Stand-up controls (HS), std. kg 60 60 60 60 60 60 60Stand-up controls (HS), direct valve control kg 70 70 70 70 70 70 70
Top seat (TS) kg 90 90 90 90 90 90 90Top seat, ladder kg 20 20 20 20 20 20 201 extra valve, hose guides kg 55 65 75 85 951 extra valve, hose reels kg 95 951 extra valve, int. hose routing kg 75 75 80 80 852 extra valves, hose guides kg 75 90 105 120 1352 extra valves, hose reels kg 185 1852 extra valves, int. hose routing kg 130 130 140 145 150Winch (1.5 t), single snatch block kg 175 175 175 175 180 180 190
Winch (1.5 t), double snatch block kg 170 170 170 170 175 175 180
Winch (2.5 t), single snatch block kg 200 200 200 200 205 205 210
Winch (2.5 t), double snatch block kg 195 195 195 195 200 200 205
High-pressure filiter kg 7 7 7 7 7 7 7
Oil cooler kg 25 25 25 25 25 25 25
Max. Load on stabilizers (per stabilizer cylinder) Unit K2 K3 K4 K5 K6 K7 K8
S1, fixed kN 120 120 120 120 120 120 120S1, swing-up kN 120 120 120 120 120 120 120S1, hydr. swing-up kN 120 120 120 120 120 120 120D, fixed kN 100 100 100 100 100 100 100D, swing-up kN 100 100 100 100 100 100 100D, hydr. swing-up kN 100 100 100 100 100 100 100
Power consumption(oil capacity) Unit K2 K3 K4 K5 K6 K7 K8
Working pressure Bar 345 345 345 345 345 345 345
Tank capacity (fitted on loader) L 90 90 90 90 90 90 90Max. pump performance, Hydrocontrol, 1-circuit L/min 60 60 60 60 60 60 60
Max. pump performance, Hydrocontrol, 2-circuit L/min - - - - - - -
Max. pump performance, Danfoss fixed flow L/min 70 70 70 70 70 70 70
Max. pump performance, Danfoss variable L/min 120 120 120 120 120 120 120
This page left intentionally blank
8
26/180 - Manual # 99904617
Section - 2 9 26/180SL Load Capacity Charts
26/180 - Manual # 99904617
Section - 226/180SL Load Capacity Charts
Section - 2 10 26/180SL Load Capacity Charts
26/180 - Manual # 99904617
26/180SL Lifting Capacity Chart, K2
70399718
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model26/180SL K2
Working loads will be limited to those shown.Deduct the weight of load handling devices.
Before lift is made, stability must be checked per SAE J765A.
03'
6'9'
12'15'
18'21'
24'CENTERLINE
(0.91m)
(1.83m)
(2.74m)
(3.66m)
(4.57m)
(5.49m)
(6.40m) (8.23m)
(7.32m)27'
0MOUNTINGSURFACE
(0.91m)
6'(1.83m)
9'(2.74m)
12'(3.66m)
15'(4.57m)
18'(5.49m)
21'(6.40m)
24'(7.32m)
27'(8.23m)
30'(9.14m)
33'(10.06m)
3'
KGLB
84903850
200209080
64402920
123005580
Section - 2 11 26/180SL Load Capacity Charts
26/180 - Manual # 99904617
26/180SL Lifting Capacity Chart, K3
70399719
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model26/180SL K3
Working loads will be limited to those shown.Deduct the weight of load handling devices.
Before lift is made, stability must be checked per SAE J765A.
0CENTERLINE
6'(1.83m)
12'(3.66m)
18'(5.49m)
24'(7.32m)
30'(9.14m)
3'(0.91m)
9'(2.74m)
15'(4.57m)
21'(6.40m)
27'(8.23m)
33'(10.06m)
MOUNTINGSURFACE
6'(1.83m)
12'(3.66m)
18'(5.49m)
24'(7.32m)
30'(9.14m)
36'(10.97m)
42'(12.80m)
0
80903670
189608600
60652750
48502200
KGLB
118155360
Section - 2 12 26/180SL Load Capacity Charts
26/180 - Manual # 99904617
26/180SL Lifting Capacity Chart, K4
70399720
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model26/180SL K4
6'
9'3'
12'
15'
18'
21'
24'
27'
30'
33'
36'
39'
0CENTERLINE
(0.91m) (2.74m) (4.57m) (6.40m) (8.23m) (10.06m)
(1.83m) (3.66m) (5.49m) (7.32m) (9.14m) (10.97m)42'
(12.80m)
(11.89m)
0MOUNTINGSURFACE
6'(1.83m)
12'(3.66m)
18'(5.49m)
24'(7.32m)
30'(9.14m)
36'(10.97m)
42'(12.80m)
48'(14.63m)
113555150
76953490
180108170
57102590
44502040
37051680
KGLB
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
Section - 2 13 26/180SL Load Capacity Charts
26/180 - Manual # 99904617
26/180SL Lifting Capacity Chart, K5
70399721
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model26/180SL K5
Working loads will be limited to those shown.Deduct the weight of load handling devices.
Before lift is made, stability must be checked per SAE J765A.
6'
9'3'
12'
15'
18'
21'
24'
27'
30'
33'
36'
39'
0CENTERLINE
(0.91m) (2.74m) (4.57m) (6.40m) (8.23m) (10.06m)
(1.83m) (3.66m) (5.49m) (7.32m) (9.14m) (10.97m)
(11.89m)
42'
45'(12.80m)
48'(14.63m)
(13.72m)
0MOUNTINGSURFACE
6'(1.83m)
12'(3.66m)
18'(5.49m)
24'(7.32m)
30'(9.14m)
36'(10.97m)
42'(12.80m)
48'(14.63m)
54'(16.46m)KG
LB
109604970
73653340
171307770
53802440
41901900
33951540
28451290
113105130
Section - 2 14 26/180SL Load Capacity Charts
26/180 - Manual # 99904617
26/180SL Lifting Capacity Chart, K6
70399722
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model26/180SL K6
Working loads will be limited to those shown.Deduct the weight of load handling devices.
Before lift is made, stability must be checked per SAE J765A.
6'
9'3'
12'
15'
18'
21'
24'
27'
30'
33'
36'
39'
0CENTERLINE
(0.91m) (2.74m) (4.57m) (6.40m) (8.23m) (10.06m)
(1.83m) (3.66m) (5.49m) (7.32m) (9.14m) (10.97m)
(11.89m)
42'
45'(12.80m)
48'(14.63m)
(13.72m)51'
54'(16.46m)
(15.54m)
0MOUNTINGSURFACE
6'(1.83m)
12'(3.66m)
18'(5.49m)
24'(7.32m)
30'(9.14m)
36'(10.97m)
42'(12.80m)
48'(14.63m)
54'(16.46m)
60'(18.29m)
KGLB
105404780
70103180
168657650
50702300
38801760
30901400
25601160
2180990
113105130
Section - 2 15 26/180SL Load Capacity Charts
26/180 - Manual # 99904617
26/180SL Lifting Capacity Chart, K7
70399723
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model26/180SL K7
Working loads will be limited to those shown.Deduct the weight of load handling devices.
Before lift is made, stability must be checked per SAE J765A.
6'
9'3'
12'
15'
18'
21'
24'
27'
30'
33'
36'
39'
0CENTERLINE
(0.91m) (2.74m) (4.57m) (6.40m) (8.23m) (10.06m)
(1.83m) (3.66m) (5.49m) (7.32m) (9.14m) (10.97m)
(11.89m)
42'
45'(12.80m)
48'(14.63m)
(13.72m)51'
54'(16.46m)
(15.54m)57'
60'(18.29m)
(17.37m)63'
(19.20m)
0MOUNTINGSURFACE
6'(1.83m)
12'(3.66m)
18'(5.49m)
24'(7.32m)
30'(9.14m)
36'(10.97m)
42'(12.80m)
48'(14.63m)
54'(16.46m)
60'(18.29m)
66'(20.12m)
67703070
48302190
161407320
36601660
28651300
23401060
1985900
1740790
102304640
KGLB
113105130
Section - 2 16 26/180SL Load Capacity Charts
26/180 - Manual # 99904617
26/180SL Lifting Capacity Chart, K8
70399724
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model26/180SL K8
Working loads will be limited to those shown.Deduct the weight of load handling devices.
Before lift is made, stability must be checked per SAE J765A.
6'
9'3'
12'
15'
18'
21'
24'
27'
30'
33'
36'
39'
0CENTERLINE
(0.91m) (2.74m) (4.57m) (6.40m) (8.23m) (10.06m)
(1.83m) (3.66m) (5.49m) (7.32m) (9.14m) (10.97m)
(11.89m)
42'
45'(12.80m)
48'(14.63m)
(13.72m)51'
54'(16.46m)
(15.54m)57'
60'(18.29m)
(17.37m)63'
(19.20m)
66'
69'(20.03m)
(20.12m)
0MOUNTINGSURFACE
6'(1.83m)
12'(3.66m)
18'(5.49m)
24'(7.32m)
30'(9.14m)
36'(10.97m)
42'(12.80m)
48'(14.63m)
54'(16.46m)
60'(18.29m)
66'(20.12m)
72'(21.95m)
78'(23.77m)
64602930
45652070
154307000
33951540
26251190
2095950
1520690
1345610
98554470
1740790
72303280
113105130
KGLB
Section - 2 17 26/180SL Load Capacity Charts
26/180 - Manual # 99904617
26/180SL Lifting Capacity K2 - K8
K2
K3
K4
K5
K6
K7
K8
Lifting capacity without manual extensionsLifting capacity with manual extensions
lbsft
1230014'1"
849020'4"
644026’11”
kgm
55804.3
38506.2
29208.2
lbsft
1181514'5"
809020'8"
606526'11"
485033'5
kgm
53604.4
36706.3
27508.2
220010.2
lbsft
1135014'9"
769521’
lbsft
1096015'1"
736521’
lbsft
1054015'1"
701021'4"
507027’10”
388034'5"
309041'4"
256048'6"
218055'9"
159863'8"
115771'2"
70579'
kgm
47804.6
31806.5
23008.5
176010.5
140012.6
116014.8
99017.0
72519.4
52521.7
32024.1
lbsft
1023015'5"
677021'7"
483027’10”
366034'5"
286541'4"
234048'7"
198556'1"
174063’
115770'10"
70578'5"
kgm
m
46404.7
30706.6
21908.5
166010.5
133012.6
106014.8
90017.1
79019.2
52521.6
32023.9
lbsft
985515'9"
646022’
456528'3"
339534'9"
262541'8"
209548'11"
174056'5"
152063'4"
134570'6"
70578'5"
kg 44704.8
29306.7
20708.6
145010.6
119012.7
95014.9
79017.2
69019.3
61021.5
32023.9
538027'7"
419034'1"
339541’1”
284548'2"
220556'1"
176363'8"
115771'2"
kgm
49704.6
33406.4
24408.4
190010.4
154012.5
129014.7
100017.1
80019.4
52521.7
571027'3"
445033'9"
370540'8"
295448'3"
231556'1"
181963'8"
kgm
51504.5
24906.4
25908.3
204010.3
168012.4
134014.7
104017.1
82519.4
This page left intentionally blank
18
26/180 - Manual # 99904617
Section - 3 19 26/180SL Hydraulics
26/180 - Manual # 99904617
Section - 326/180SL Hydraulics
Section - 3 20 26/180SL Hydraulics
26/180 - Manual # 99904617
26/180SL - Pressure setting diagram, fixed flow pump & Danfoss RC
Working Pressure on Main-Relief Valve & Port- Relief Valves
Function Direction PortPort-relief
valves [bar]
LS-pressure adjustment
[bar]
Port-relief valves [PSI]
LS-pressure adjustment
[PSI]Main-relief valve 345 5004
Slewing systemRight A P 205 P 2973Left B P 205 P 2973
Boom cylinderDown A 125 100 1813 1450Up B 350 380 5076 5511
Jib cylinderUp A 350 380 5076 5511Down B 250 230 3626 3336
Extension cylindersExtend A P - P -Retract B P - P -
RotatorRight A P 50-300 P 725-4351Left B P 50-300 P 725-4351
GrabOpen A P 50-300 P 725-4351Close B P 50-300 P 725-4351
Winch 1,5TLift A P 160 P 2321Lower B P 160 P 2321
Winch 2,5TLift A P 185 P 2683Lower B P 185 P 2683
Separate stabilizer valve All 150 2176
Working Pressure on Load-holding ValvesFunction Direction Opening pressure [bar] Opening pressure [PSI]
Slewing systemRight 210 3046Left 210 3046
Boom cylinderUp 365 5294
Down - -
Jib cylinderUp 380 5511
Down 300 4351
Extension cylindersRetract 430 6237Extend 210 3046
Pressure setting for Load Moment Limitation (LMB)Load moment limitation (LMB) 330 [bar] 4786 [PSI]HDL 285 [bar] 4134 [PSI]
Max. pump performanceChoice of pump 1 x Fixed 1 x FixedPump performance 70 L/min 18.5 gpm
IMT reserves the right to introduce improvements and modifications
Section - 3 21 26/180SL Hydraulics
26/180 - Manual # 99904617
26/180SL - Pressure setting diagram, variable flow pump & Danfoss RC
Working Pressure on Main-Relief Valve & Port- Relief Valves
Function Direction PortPort-relief
valves [bar]
LS-pressure adjustment
[bar]
Port-relief valves [PSI]
LS-pressure adjustment
[PSI]Main-relief valve 345 5004
Slewing systemRight A P 210 P 3046Left B P 210 P 3046
Boom cylinderDown A 125 100 1813 1450Up B 350 380 5076 5511
Jib cylinderUp A 350 380 5076 5511Down B 250 230 3626 3336
Extension cylindersExtend A P 300 P 4351Retract B P 300 P 4351
RotatorRight A P 50-300 P 725-4351Left B P 50-300 P 725-4351
GrabOpen A P 50-300 P 725-4351Close B P 50-300 P 725-4351
Winch 1,5TLift A P 160 P 2321Lower B P 160 P 2321
Winch 2,5TLift A P 185 P 2683Lower B P 185 P 2683
Separate stabilizer valve All 150 2176
Working Pressure on Load-holding ValvesFunction Direction Opening pressure [bar] Opening pressure [PSI]
Slewing systemRight 210 3046Left 210 3046
Boom cylinderUp 365 5294
Down - -
Jib cylinderUp 380 5511
Down 300 4351
Extension cylindersRetract 430 6237Extend 210 3046
Pressure setting for Load Moment Limitation (LMB)Load moment limitation (LMB) 330 [bar] 4786 [PSI]HDL 285 [bar] 4134 [PSI]
Max. pump performanceChoice of pump 1 x Variable 1 x VariablePump performance 120 L/min 31.7 gpm
IMT reserves the right to introduce improvements and modifications
Section - 3 22 26/180SL Hydraulics
26/180 - Manual # 99904617
Hydraulic Diagram - Danfoss, single-circuit fixed 6 fcts. RC (2 EXV: Grab + Rotator)
Option
B1M3
B
A
M2
M1
A1
55227
C2 C1
V2 V1
5904
4
5526
1 / 5
5262
A1 B1
A B
5902
7
MM2M1 C1C2
V1V2
P PVSK
HPCO
63093/63302/63304/63319
X4
X1
X2
X3
Pst
Tst PVP
T
P
LS M
A-PORTA1
B1
A-PORTA2
B2
A-PORTA3
B3
A-PORTA4
B4
A-PORTA5
B5
A-PORTA6
B6
58478
58478
58478
58478
58478
58478
58478
58478
58478
58479
4940
1
Section - 3 23 26/180SL Hydraulics
26/180 - Manual # 99904617
Hydraulic Diagram - Danfoss, single-circuit variable 6 fcts. RC/HS dir. valve contr. (2 EXV: Grab + Rotator)
Option
Recommended
B1M3
B
A
M2
M1
A1
55227
C2 C1
V2 V1
5904
4
PVP
T
P
LS M
5526
1 / 5
5262
A1 B1
A B
5902
7
MM2M1 C1C2
V1V2
X4
X1
X2
X3
A-PORTA6
B6
A-PORTA5
B5
A-PORTA4
B4
A3
B3
A-PORT
A-PORTA2
B2
A-PORTA1
B1
63092/63301/63303/63313
P PVSKPst
Tst
58478
58478
58478
58478
58478
58478
58478
58478
58478
58479
4940
1
Section - 3 24 26/180SL Hydraulics
26/180 - Manual # 99904617
Hydraulic Diagram - Stabilizer circuit – 2 fcts.
PstTst
A-PORT
A2 B2
A-PORT
A1 B1
5522
5
PT
5849
6
5849
6
Section - 3 25 26/180SL Hydraulics
26/180 - Manual # 99904617
Hydraulic Diagram - Stabilizer circuit – 4 fcts.
PstTst
D
C
5522
8
5849
6
5849
6
D
C
5522
8
A14 B14 A13 B13 A12 B12 A11 B11
5522
6 / 5
5281
PT
A-PORT A-PORT A-PORTA-PORT
Section - 3 26 26/180SL Hydraulics
26/180 - Manual # 99904617
Hydraulic Diagram - Stabilizer circuit – 4 fcts. RC
D
C
5522
8
5849
6
5849
6
D
C
5522
8
PstTst
A13 B13 A12 B12
5527
6
T
B-PORT
A-PORT
A11 B11
PA-PORT
B-PORT
NEM-MODULPT
T
ø1 mmø1 mm
50521
C1
C2
C3
D1
D2
D3
D4
C4
49187
49187
Only when HR stabilizer
Section - 3 27 26/180SL Hydraulics
26/180 - Manual # 99904617
Hydraulic Diagram - Stabilizer circuit – 4 fcts. + 4 available fcts.
D
C
5522
8
5849
6
5849
6
D
C
5522
8
Separate traverse
PstTst
A15 B15 A14 B14 A13 B13 A12 B12
5527
7
TA-PORT
B-PORT
A-PORTA-PORT
A11 B11
PA-PORT
OPT.
B-PORTB-PORTB-PORT
OPT.OPT.OPT.
ø1 mm ø1 mm
50521
C1
C2
C3
D1
D2
D3
D4
C4
Section - 3 28 26/180SL Hydraulics
26/180 - Manual # 99904617
Hydraulic Diagram - Stabilizer circuit – 4 fcts. + 4 available fcts. RC
D
C
5522
8
5849
6
5849
6
D
C
5522
8
Separate traverse
PstTst
P
P
A15 B15 A14 B14 A13 B13 A12 B12
5527
5
TA-PORT
B-PORT
A-PORTA-PORT
A11 B11
A-PORT
OPT.
B-PORTB-PORTB-PORT
OPT.OPT.OPT.
NEM-MODULT
T
ø1 mm ø1 mm
50521
C1
C2
C3
D1
D2
D3
D4
C4
Only when HR stabilizer
49187
49187
This page left intentionally blank
29
26/180 - Manual # 99904617
This page left intentionally blank
30
26/180 - Manual # 99904617
Section - 4 31 26/180DL Technical Specifications
26/180 - Manual # 99904617
Section - 426/180DL Technical Specifications
Section - 4 32 26/180DL Technical Specifications
26/180 - Manual # 99904617
26/180DL Specifications
Performance Unit K2 K3 K4 K5 K6 K7 K8Loading group (EN12999) H1/B3 H1/B3 H1/B3 H1/B3 H1/B3 H1/B3 H1/B3
Load moment ft-lb 174680 171071 166740 163853 160244 158078 155191Hydraulic reach ft 27’2’’ 33’8’’ 41’0’’ 48’6’’ 56’1’’ 63’4’’ 70’10’’Hydraulic telescopic movement ft 12’6” 19’1” 26’ 33’2” 40’5” 47’7” 54’9”
Lifting capacity, hydraulic lb-ft 12324 -
14’1’’11840 - 14’5’’
11375 - 14’9’’
10980 - 15’1’’
10560 - 15’1’’
10250 - 15’5’’
9900 - 15’9’’
8510 - 20’4’’
8115 - 20’6’’ 7715 - 21’ 7385 - 21’ 7030 -
21’4’’6790 - 21’8’’
6480 - 22’’
6459 - 26’11’’
6085 - 26’9’’
5730 - 27’3’’
5400 - 27’7’’
5070 - 27’11’’
4850 - 27’11’’
4585 - 28’3’’
4870 - 33’6’’
4520 - 33’9’’
4190 - 34’1’’
3880 - 34’5’’
3660 - 34’5’’
3420 - 34’9’’
3700 - 40’8’’
3395 - 41’0’’
3086 - 41’4’’
2890 - 41’4’’
2645 - 41’8’’
2865 - 48’3’’
2555 - 48’7’’
2335 - 48’7’’
2115 - 48’11’’
2205 - 55’9’’
1985 - 56’1’’
1740 - 56’5’’
1740 - 63’ 1520 - 63’4’’1345 - 70’6’’
Lifting capacity, manual extensions
lb-ft 2294 - 48’3’’
2205- 56’1’’
1595 - 63’8’’
1157 - 70’10’’
705 - 78’5’’
2315 - 56’1’’
1763 - 63’8’’
1157 - 71’2’’ 705 - 78’5’’
1818 - 63’8’’
1157 - 71’2’’ 705 - 79’0’’
Slewing torque, gross lbft 17553 17553 17553 17553 17553 17553 17553
Slewing angle ° 400 400 400 400 400 400 400Max. heel at max. load moment ° 5 5 5 5 5 5 5
Slewing speed °/s 24 24 24 24 24 24 24
Minimum Chassis SpecsFront Axle Rating (GAWR) 14,000 lbs (6,50 kg)Rear Axle Rating (GAWR) 40,000 lbs (18,150 kg)Resistance to Bending Moment 2,700,000 in-lbs (373,300 kg-m)
Section - 4 33 26/180DL Technical Specifications
26/180 - Manual # 99904617
26/180DL Specifications - Continued
Dimensions Unit K2 K3 K4 K5 K6 K7 K8Height above chassis in 90 90 90 90 90 90 91Width in 98 98 98 98 98 98 98Length, no extra valves in 34 34 34 34 34 39 39Length, with extra valves (hose guides) in 39 39 39 39 39
Length, with 1 extra valve (hose reels) in 39 39
Length, with 2 extra valves (hose reels) in 40 40
Length, with extra valves (int. hose routing) in 34 34 34 34 34
Stabilizer spread, S1 (standard) ft 18’3” 18’3” 18’3” 18’3” 18’3” 18’3” 18’3”
Stabilizer spread, D ft 21’2” 21’2” 21’2” 21’2” 21’2” 21’2” 21’2”
Weights, basic loader Unit K2 K3 K4 K5 K6 K7 K8Standard loader 1), excl. stabilizers lbs 4365 4740 5181 5512 5820 6052 6239
Stabilizers, S1 fixed lbs 639 639 639 639 639 639 639
Stabilizers, S1 swing-up lbs 650 650 650 650 650 650 650Stabilizers, S1 hydr. swing-up lbs 661 661 661 661 661 661 661
Stabilizers, D fixed lbs 805 805 805 805 805 805 805Stabilizers, D swing-up lbs 816 816 816 816 816 816 816Stabilizers, D hydr. swing-up lbs 827 827 827 827 827 827 827
Mounting kit, 4 bolts lbs 143 143 143 143 143 143 143Mounting kit, 8 bolts lbs 132 132 132 132 132 132 132Tank, excl. oil (fitted on loader) lbs 99 99 99 99 99 99 99
Manual extensions lbs 176 154 132 99 77lbs 154 132 99 77lbs 132 99 77
Oil in loader (stowing position) lbs 88 99 110 121 132 143 143
Section - 4 34 26/180DL Technical Specifications
26/180 - Manual # 99904617
26/180DL Specifications - Continued
Weights, equipment Unit K2 K3 K4 K5 K6 K7 K8Stand-up controls (HS), std. lbs 132 132 132 132 132 132 132Stand-up controls (HS), direct valve control lbs 154 154 154 154 154 154 154
Top seat (TS) lbs 198 198 198 198 198 198 198Top seat, ladder lbs 44 44 44 44 44 44 441 extra valve, hose guides lbs 121 143 165 187 2091 extra valve, hose reels lbs 209 2091 extra valve, int. hose routing lbs 165 165 176 176 1872 extra valves, hose guides lbs 165 198 231 265 2982 extra valves, hose reels lbs 408 4082 extra valves, int. hose routing lbs 287 287 309 320 331Winch (1.5 t), single snatch block lbs 386 386 386 386 397 397 419
Winch (1.5 t), double snatch block lbs 375 375 375 375 386 386 397
Winch (2.5 t), single snatch block lbs 441 441 441 441 452 452 463
Winch (2.5 t), double snatch block lbs 430 430 430 430 441 441 452
High-pressure filter lbs 15 15 15 15 15 15 15
Oil cooler lbs 55 55 55 55 55 55 55
1) Weights ± 5% because of tolerances for plate thickness
Max. Load on stabilizers (per stabilizer cylinder) Unit K2 K3 K4 K5 K6 K7 K8
S1, fixed Lbf 26 26 26 26 26 26 26S1, swing-up Lbf 26 26 26 26 26 26 26S1, hydr. swing-up Lbf 26 26 26 26 26 26 26D, fixed Lbf 22 22 22 22 22 22 22D, swing-up Lbf 22 22 22 22 22 22 22D, hydr. swing-up Lbf 22 22 22 22 22 22 22
Power consumption(oil capacity) Unit K2 K3 K4 K5 K6 K7 K8
Working pressure PSI 5003 5003 5003 5003 5003 5003 5003
Tank capacity (fitted on loader) Gal 23 23 23 23 23 23 23Max. pump performance, Hydrocontrol, 1-circuit Gpm 15 15 15 15 15 15 15
Max. pump performance, Hydrocontrol, 2-circuit Gpm - - - - - - -
Max. pump performance, Danfoss fixed flow Gpm 18 18 18 18 18 18 18
Max. pump performance, Danfoss variable Gpm 31 31 31 31 31 31 31
Section - 4 35 26/180DL Technical Specifications
26/180 - Manual # 99904617
26/180DL Metric Specifications
Performance Unit K2 K3 K4 K5 K6 K7 K8Loading group (EN12999) H1/B3 H1/B3 H1/B3 H1/B3 H1/B3 H1/B3 H1/B3
Load moment tm 19.5 19.1 18.6 18.1 17.7 17.2 17Hydraulic reach m 8.3 10.3 12.5 14.8 17.1 19.3 21.6Hydraulic telescopic movement mm 3830 5840 7930 10130 12370 14520 16720
Lifting capacity, hydraulic kg-m 4510 - 4.3 4330 - 4.4 4150 - 4.5 3980 - 4.6 3820 - 4.6 3660 - 4.7 3550 - 4.8
3110 - 6.2 2950 - 6.3 2790 - 6.4 2650 - 6.4 2510 - 6.5 2380 - 6.6 2290 - 6.7
2360 - 8.2 2200 - 8.2 2050 - 8.3 1920 - 8.4 1790 - 8.5 1670 - 8.5 1590 - 8.6
1760 - 10.2
1610 - 10.3
1480 - 10.4
1360 - 10.5
1230 - 10.5
1160 - 10.6
1330 - 12.4 1190 - 12.5 1070 -
12.6 950 - 12.6 880 - 12.7
1000 - 14.7 880 - 14.8 760 - 14.8 690 - 14.9
750 - 17.0 630 - 17.1 560 - 17.2
550 - 19.2 480 - 19.3
430 - 21.5
Lifting capacity, manual extensions kg-m 1040 -
14.7 790 - 17.1 550 - 19.4 425 - 21.6 320 - 23.9
840 - 17.1 620 - 19.4 450 - 21.7 320 - 23.9660 - 19.4 500 - 21.7 325 - 24.1
Slewing torque, gross kNm 23.8 23.8 23.8 23.8 23.8 23.8 23.8
Slewing angle ° 400 400 400 400 400 400 400Max. heel at max. load moment ° 5 5 5 5 5 5 5
Slewing speed °/s 24 24 24 24 24 24 24
Section - 4 36 26/180DL Technical Specifications
26/180 - Manual # 99904617
26/180DL Metric Specifications - Continued
Dimensions Unit K2 K3 K4 K5 K6 K7 K8Height above chassis mm 2295 2295 2295 2295 2295 2295 2335Width mm 2500 2500 2500 2500 2500 2500 2500Length, no extra valves mm 885 885 885 885 885 995 995Length, with extra valves (hose guides) mm 1005 1005 1005 1005 1005
Length, with 1 extra valve (hose reels) mm 995 995
Length, with 2 extra valves (hose reels) mm 1030 1030
Length, with extra valves (int. hose routing) mm 885 885 885 885 885
Stabilizer spread, S1 (standard) mm 5575 5575 5575 5575 5575 5575 5575
Stabilizer spread, D mm 6455 6455 6455 6455 6455 6455 6455
Weights, basic loader Unit K2 K3 K4 K5 K6 K7 K8Standard loader 1), excl. stabilizers kg 1980 2150 2350 2500 2640 2745 2830
Stabilizers, S1 fixed kg 290 290 290 290 290 290 290
Stabilizers, S1 swing-up kg 295 295 295 295 295 295 295Stabilizers, S1 hydr. swing-up kg 300 300 300 300 300 300 300
Stabilizers, D fixed kg 365 365 365 365 365 365 365Stabilizers, D swing-up kg 370 370 370 370 370 370 370Stabilizers, D hydr. swing-up kg 375 375 375 375 375 375 375
Mounting kit, 4 bolts kg 65 65 65 65 65 65 65Mounting kit, 8 bolts kg 60 60 60 60 60 60 60Tank, excl. oil (fitted on loader) kg 45 45 45 45 45 45 45
Manual extensions kg 80 70 60 45 35kg 70 60 45 35kg 60 45 35
Oil in loader (stowing position) kg 40 45 50 55 60 65 65
Section - 4 37 26/180DL Technical Specifications
26/180 - Manual # 99904617
26/180DL Metric Specifications - Continued
Weights, equipment Unit K2 K3 K4 K5 K6 K7 K8Stand-up controls (HS), std. kg 60 60 60 60 60 60 60Stand-up controls (HS), direct valve control kg 70 70 70 70 70 70 70
Top seat (TS) kg 90 90 90 90 90 90 90Top seat, ladder kg 20 20 20 20 20 20 201 extra valve, hose guides kg 55 65 75 85 951 extra valve, hose reels kg 95 951 extra valve, int. hose routing kg 75 75 80 80 852 extra valves, hose guides kg 75 90 105 120 1352 extra valves, hose reels kg 185 1852 extra valves, int. hose routing kg 130 130 140 145 150Winch (1.5 t), single snatch block kg 175 175 175 175 180 180 190
Winch (1.5 t), double snatch block kg 170 170 170 170 175 175 180
Winch (2.5 t), single snatch block kg 200 200 200 200 205 205 210
Winch (2.5 t), double snatch block kg 195 195 195 195 200 200 205
High-pressure filter kg 7 7 7 7 7 7 7
Oil cooler kg 25 25 25 25 25 25 25
1) Weights ± 5% because of tolerances for plate thickness
Max. Load on stabilizers (per stabilizer cylinder) Unit K2 K3 K4 K5 K6 K7 K8
S1, fixed kN 120 120 120 120 120 120 120S1, swing-up kN 120 120 120 120 120 120 120S1, hydr. swing-up kN 120 120 120 120 120 120 120D, fixed kN 100 100 100 100 100 100 100D, swing-up kN 100 100 100 100 100 100 100D, hydr. swing-up kN 100 100 100 100 100 100 100
Power consumption(oil capacity) Unit K2 K3 K4 K5 K6 K7 K8
Working pressure Bar 345 345 345 345 345 345 345
Tank capacity (fitted on loader) L 90 90 90 90 90 90 90Max. pump performance, Hydrocontrol, 1-circuit L/min 60 60 60 60 60 60 60
Max. pump performance, Hydrocontrol, 2-circuit L/min - - - - - - -
Max. pump performance, Danfoss fixed flow L/min 70 70 70 70 70 70 70
Max. pump performance, Danfoss variable L/min 120 120 120 120 120 120 120
This page left intentionally blank
38
26/180 - Manual # 99904617
Section - 5 39 26/180DL Load Capacity Charts
26/180 - Manual # 99904617
Section - 526/180DL Load Capacity Charts
Section - 5 40 26/180DL Load Capacity Charts
26/180 - Manual # 99904617
26/180DL Lifting Capacity Chart, K2
70399727
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model26/180DL K2
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
0CENTERLINE 3'
6'9'
12'15'
18'21'
24'27'
30'
0MOUNTINGSURFACE
3'(0.91m)
6'(1.83m)
9'(2.74m)
12'(3.66m)
15'(4.57m)
18'(5.49m)
21'(6.40m)
24'(7.32m)
27'(8.23m)
30'(9.14m)
33'(10.06m)
(0.91m)
(1.83m)
(2.74m)
(3.66m)
(4.57m)
(5.49m)
(6.40m)
(7.32m)
(8.23m)
(9.14m)
202609190
123245590
85103860
64592930
KGLB
Section - 5 41 26/180DL Load Capacity Charts
26/180 - Manual # 99904617
26/180DL Lifting Capacity Chart, K3
70399728
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model26/180DL K3
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
0CENTERLINE 3'
6'9'
12'15'
18'21'
24'27'
30'33'
0MOUNTINGSURFACE
3'(0.91m)
6'(1.83m)
9'(2.74m)
12'(3.66m)
15'(4.57m)
18'(5.49m)
21'(6.40m)
24'(7.32m)
27'(8.23m)
30'(9.14m)
33'(10.06m)
36'(10.97m)
39'(11.89m)
42'(12.80m)
KGLB
(0.91m)
(1.83m)
(2.74m)
(3.66m)
(4.57m)
(5.49m)
(6.40m)
(7.32m)
(8.23m) (10.06m)
(9.14m)
194458820
118405370
81153680
60852760
48702210
Section - 5 42 26/180DL Load Capacity Charts
26/180 - Manual # 99904617
26/180DL Lifting Capacity Chart, K4
70399729
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model26/180DL K4
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
6' 12' 18' 24' 30' 36' 42'0CENTERLINE
0MOUNTINGSURFACE
6'(1.83m)
12'(3.66m)
18'(5.49m)
24'(7.32m)
30'(9.14m)
36'(10.97m)
42'(12.80m)
48'(14.63m)
54'(16.46m)
(1.83m) (3.66m) (5.49m) (7.32m) (10.97m)(9.14m) (12.80m)
3' 9' 15' 21' 27' 33' 39'(0.91m) (2.74m) (4.57m) (6.40m) (8.23m) (10.06m) (11.89m)
45'(13.72m)
186508460
113755160
77153500
57302600
45202050
37001680
KGLB
Section - 5 43 26/180DL Load Capacity Charts
26/180 - Manual # 99904617
26/180DL Lifting Capacity Chart, K5
70399730
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model26/180DL K5
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
6' 12' 18' 24' 30' 36' 42' 48' 54'0CENTERLINE
0MOUNTINGSURFACE
6'(1.83m)
12'(3.66m)
18'(5.49m)
24'(7.32m)
30'(9.14m)
36'(10.97m)
42'(12.80m)
48'(14.63m)
54'(16.46m)
60'(18.29m)
(1.83m) (3.66m) (5.49m) (7.32m) (10.97m)(9.14m) (12.80m) (14.63m)(16.46m)
3' 9' 15' 21' 27' 33' 39'(0.91m) (2.74m) (4.57m) (6.40m) (8.23m) (10.06m) (11.89m)
45'(13.72m)
51'(15.55m)
113105130
179458140
109804980 7385
335054002450 4190
1900 33951540
28651300
KGLB
Section - 5 44 26/180DL Load Capacity Charts
26/180 - Manual # 99904617
26/180DL Lifting Capacity Chart, K6
70399731
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model26/180DL K6
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
6'
9'3'
12'
15'
18'
21'
24'
27'
30'
33'
36'
39'
0CENTERLINE
(0.91m) (2.74m) (4.57m) (6.40m) (8.23m) (10.06m)
(1.83m) (3.66m) (5.49m) (7.32m) (9.14m) (10.97m)
(11.89m)
42'
45'(12.80m)
48'(14.63m)
(13.72m)51'
54'(16.46m)
60'(18.29m)
(15.54m)57'
(17.37m)
0MOUNTINGSURFACE
6'(1.83m)
12'(3.66m)
18'(5.49m)
24'(7.32m)
30'(9.14m)
36'(10.97m)
42'(12.80m)
48'(14.63m)
54'(16.46m)
60'(18.29m)
66'(18.29m)
113105130
172607830
105604790
70303190
50702300
38801760
30861400
22551160
22051000
KGLB
Section - 5 45 26/180DL Load Capacity Charts
26/180 - Manual # 99904617
26/180DL Lifting Capacity Chart, K7
70399732
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model26/180DL K7
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
6'
9'3'
12'
15'
18'
21'
24'
27'
30'
33'
36'
39'
0CENTERLINE
(0.91m) (2.74m) (4.57m) (6.40m) (8.23m) (10.06m)
(1.83m) (3.66m) (5.49m) (7.32m) (9.14m) (10.97m)
(11.89m)
42'
45'(12.80m)
48'(14.63m)
(13.72m)51'
54'(16.46m)
(15.54m)57'
60'(18.29m)
(17.37m)63'
(19.20m)
0MOUNTINGSURFACE
6'(1.83m)
12'(3.66m)
18'(5.49m)
24'(7.32m)
30'(9.14m)
36'(10.97m)
42'(12.80m)
48'(14.63m)
54'(16.46m)
60'(18.29m)
66'(20.12m)
KGLB
102504650
67903080
48502200
36601660
28901310
23351060
1985900
1740790
166457550
113105130
Section - 5 46 26/180DL Load Capacity Charts
26/180 - Manual # 99904617
26/180DL Lifting Capacity Chart, K8
70399733
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model26/180DL K8
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
6'
9'3'
12'
15'
18'
21'
24'
27'
30'
33'
36'
39'
0CENTERLINE
(0.91m) (2.74m) (4.57m) (6.40m) (8.23m) (10.06m)
(1.83m) (3.66m) (5.49m) (7.32m) (9.14m) (10.97m)
(11.89m)
42'
45'(12.80m)
48'(14.63m)
(13.72m)51'
54'(16.46m)
(15.54m)57'
60'(18.29m)
(17.37m)63'
(19.20m)
66'
69'(20.03m)
(20.12m)
0MOUNTINGSURFACE
6'(1.83m)
12'(3.66m)
18'(5.49m)
24'(7.32m)
30'(9.14m)
36'(10.97m)
42'(12.80m)
48'(14.63m)
54'(16.46m)
60'(18.29m)
66'(20.12m)
72'(21.95m)
78'(23.77m)
KGLB
113105130
72303280
160507280
99004490
64802940
45852080
34201550
26451200
2115960
1740790
1520690
1345610
K2
K3
K4
K5
K6
K7
K8
lbsft
1232414'1"
851020'4"
645926'9"
kgm
55904.3
38606.2
29308.2
lbsft
lbsft
lbsft
lbsft
lbsft
lbsft
990015'9"
648022’
458528'3"
342034'9"
264541'8"
211548'11"
174056'5"
152063'4"
134570'6"
70578'5"
kgm
44904.8
29406.7
20808.6
155010.6
120012.7
96014.9
79017.2
69019.3
61021.5
32023.9
1025015'5"
679021'8"
485027'11"
366034'5"
289041'4"
233548'7"
198056'1"
174063’
115770'10"
70578'5"
kgm
46504.7
30806.6
22008.5
166010.5
131012.6
106014.8
90017.1
79019.2
52521.6
32023.9
1056015'1"
703021'4"
507027'11"
388034'5"
308641'4"
255548'7"
220555'9"
159563'8"
115771'2"
kgm
47904.6
31906.5
23008.5
176010.5
140012.6
116014.8
100017.0
72519.4
52521.7
32024.1
70579’
1098015'1"
738521’
5400 27'7"
419034'1"
339541’
286548'3"
220556'1"
176363'8"
115771'2"
kgm
49804.6
33506.4
2450 8.4
190010.4
154012.5
130014.7
100017.1
80019.4
52521.7
1137514'9"
771521’
573027'3"
4520 33'9"
370040'8"
295448'3"
231556'1"
181863'8"
kgm
51604.5
35006.4
26008.3
2050 10.3
168012.4
134014.7
105017.1
82519.4
1184014'5"
811520'6"
608526'9"
487033'6"
kgm
53704.4
36806.3
27608.2
221010.2
Lifting capacity without manual extensionsLifting capacity with manual extensions
Section - 5 47 26/180DL Load Capacity Charts
26/180 - Manual # 99904617
26/180DL Lifting Capacity K2 - K8
K2
K3
K4
K5
K6
K7
K8
lbsft
1232414'1"
851020'4"
645926'9"
kgm
55904.3
38606.2
29308.2
lbsft
lbsft
lbsft
lbsft
lbsft
lbsft
990015'9"
648022’
458528'3"
342034'9"
264541'8"
211548'11"
174056'5"
152063'4"
134570'6"
70578'5"
kgm
44904.8
29406.7
20808.6
155010.6
120012.7
96014.9
79017.2
69019.3
61021.5
32023.9
1025015'5"
679021'8"
485027'11"
366034'5"
289041'4"
233548'7"
198056'1"
174063’
115770'10"
70578'5"
kgm
46504.7
30806.6
22008.5
166010.5
131012.6
106014.8
90017.1
79019.2
52521.6
32023.9
1056015'1"
703021'4"
507027'11"
388034'5"
308641'4"
255548'7"
220555'9"
159563'8"
115771'2"
kgm
47904.6
31906.5
23008.5
176010.5
140012.6
116014.8
100017.0
72519.4
52521.7
32024.1
70579’
1098015'1"
738521’
5400 27'7"
419034'1"
339541’
286548'3"
220556'1"
176363'8"
115771'2"
kgm
49804.6
33506.4
2450 8.4
190010.4
154012.5
130014.7
100017.1
80019.4
52521.7
1137514'9"
771521’
573027'3"
4520 33'9"
370040'8"
295448'3"
231556'1"
181863'8"
kgm
51604.5
35006.4
26008.3
2050 10.3
168012.4
134014.7
105017.1
82519.4
1184014'5"
811520'6"
608526'9"
487033'6"
kgm
53704.4
36806.3
27608.2
221010.2
Lifting capacity without manual extensionsLifting capacity with manual extensions
This page left intentionally blank
48
26/180 - Manual # 99904617
Section - 6 49 26/180DL Hydraulics
26/180 - Manual # 99904617
Section - 626/180DL Hydraulics
Section - 6 50 26/180DL Hydraulics
26/180 - Manual # 99904617
26/180DL - Pressure setting diagram, fixed flow pump & Danfoss RC
Working Pressure on Main-Relief Valve & Port- Relief Valves
Function Direction PortPort-relief
valves [bar]
LS-pressure adjustment
[bar]
Port-relief valves [PSI]
LS-pressure adjustment
[PSI]Main-relief valve 345 5004
Slewing systemRight A P 205 P 2973Left B P 205 P 2973
Boom cylinderDown A 125 100 1813 1450Up B 350 380 5076 5511
Jib cylinderUp A 350 380 5076 5511Down B 250 230 3626 3336
Extension cylindersExtend A P - P -Retract B P - P -
RotatorRight A P 50-300 P 725-4351Left B P 50-300 P 725-4351
GrabOpen A P 50-300 P 725-4351Close B P 50-300 P 725-4351
Winch 1,5TLift A P 160 P 2321Lower B P 160 P 2321
Winch 2,5TLift A P 185 P 2683Lower B P 185 P 2683
Separate stabilizer valve All 150 2176
Working Pressure on Load-holding ValvesFunction Direction Opening pressure [bar] Opening pressure [PSI]
Slewing systemRight 210 3046Left 210 3046
Boom cylinderUp 365 5294
Down - -
Jib cylinderUp 380 5511
Down 300 4351
Extension cylindersRetract 430 6237Extend 210 3046
Pressure setting for Load Moment Limitation (LMB)Load moment limitation (LMB) 330 [bar] 4786 [PSI]HDL 285 [bar] 4134 [PSI]
Max. pump performanceChoice of pump 1 x Fixed 1 x FixedPump performance 70 L/min 18.5 gpm
IMT reserves the right to introduce improvements and modifications
Section - 6 51 26/180DL Hydraulics
26/180 - Manual # 99904617
26/180DL - Pressure setting diagram, variable flow pump & Danfoss RC
Working Pressure on Main-Relief Valve & Port- Relief Valves
Function Direction PortPort-relief
valves [bar]
LS-pressure adjustment
[bar]
Port-relief valves [PSI]
LS-pressure adjustment
[PSI]Main-relief valve 345 5004
Slewing systemRight A P 210 P 3046Left B P 210 P 3046
Boom cylinderDown A 125 100 1813 1450Up B 350 380 5076 5511
Jib cylinderUp A 350 380 5076 5511Down B 250 230 3626 3336
Extension cylindersExtend A P 300 P 4351Retract B P 300 P 4351
RotatorRight A P 50-300 P 725-4351Left B P 50-300 P 725-4351
GrabOpen A P 50-300 P 725-4351Close B P 50-300 P 725-4351
Winch 1,5TLift A P 160 P 2321Lower B P 160 P 2321
Winch 2,5TLift A P 185 P 2683Lower B P 185 P 2683
Separate stabilizer valve All 150 2176
Working Pressure on Load-holding ValvesFunction Direction Opening pressure [bar] Opening pressure [PSI]
Slewing systemRight 210 3046Left 210 3046
Boom cylinderUp 365 5294
Down - -
Jib cylinderUp 380 5511
Down 300 4351
Extension cylindersRetract 430 6237Extend 210 3046
Pressure setting for Load Moment Limitation (LMB)Load moment limitation (LMB) 330 [bar] 4786 [PSI]HDL 285 [bar] 4134 [PSI]
Max. pump performanceChoice of pump 1 x Variable 1 x VariablePump performance 120 L/min 31.7 gpm
IMT reserves the right to introduce improvements and modifications
Section - 6 52 26/180DL Hydraulics
26/180 - Manual # 99904617
Hydraulic Diagram - Danfoss, single-circuit fixed 6 fcts. RC (2 EXV: Grab + Rotator)
Option
B1M3
B
A
M2
M1
A1
55227
C2 C1
V2 V1
5904
4
5526
1 / 5
5262
A1 B1
A B
5902
7
MM2M1 C1C2
V1V2
P PVSK
HPCO
63093/63302/63304/63319
X4
X1
X2
X3
Pst
Tst PVP
T
P
LS M
A-PORTA1
B1
A-PORTA2
B2
A-PORTA3
B3
A-PORTA4
B4
A-PORTA5
B5
A-PORTA6
B6
58478
58478
58478
58478
58478
58478
58478
58478
58478
58479
4940
1
Section - 6 53 26/180DL Hydraulics
26/180 - Manual # 99904617
Hydraulic Diagram - Danfoss, single-circuit variable 7 fcts. RC (3 EXV: FJ + 2 EXV, winch)
Option
B1M3
B
A
M2
M1
A1
55227
C2 C1
V2 V1
5904
4
C2 C1
V2 V1
5902
2
5526
1 / 5
5262
A1 B1
A B
5902
7
MM2M1 C1C2
V1V2
5902
7MM2M1 C1C2
V1V2
63310 / 63312
Pst
P PVSK
P1 P2
C1
C2
C3
C4
X2 X1 X3 X4
P2
C1
C2
C3
C4
P15906
2
5906
2
PVPTst
A-PORTA1
B1
A-PORT
A6
B6
A-PORT
A-PORT
A5
B5
A-PORT
A-PORTA4
B4
A-PORTA3
B3
A-PORTA2
B2
T
P
LS M
A-PORTA7
B7
58478
58478
58478
58478
58478
58478
58478
58478
58479
58478
58479
58479
V1 V2
5828
4/58
285
4940
1
D
58478
X3 X4
X1 X2
Fly-jib EXV:
Section - 6 54 26/180DL Hydraulics
26/180 - Manual # 99904617
Hydraulic Diagram - Danfoss, single-circuit variable 6 fcts. RC/HS dir. valve contr. (2 EXV: Grab + Rotator)
Option
Recommended
B1M3
B
A
M2
M1
A1
55227
C2 C1
V2 V1
5904
4
PVP
T
P
LS M
5526
1 / 5
5262
A1 B1
A B
5902
7
MM2M1 C1C2
V1V2
X4
X1
X2
X3
A-PORTA6
B6
A-PORTA5
B5
A-PORTA4
B4
A3
B3
A-PORT
A-PORTA2
B2
A-PORTA1
B1
63092/63301/63303/63313
P PVSKPst
Tst
58478
58478
58478
58478
58478
58478
58478
58478
58478
58479
4940
1
Section - 6 55 26/180DL Hydraulics
26/180 - Manual # 99904617
Hydraulic Diagram - Danfoss, single-circuit variable 7 fcts. RC (3 EXV: FJ + 2 EXV, winch)
Option
B1M3
B
A
M2
M1
A1
55227
C2 C1
V2 V1
5904
4
PVP
C2 C1
V2 V1
5902
2
5526
1 / 5
5262
A1 B1
A B
5902
7
MM2M1 C1C2
V1V2
5902
7MM2M1 C1C2
V1V2
63309 / 63311
Pst
P PVSKP1 P2
C1
C2
C3
C4
X2 X1 X3 X4
P2
C1
C2
C3
C4
P15906
2
5906
2
Recommended
Tst
A-PORTA1
B1
A-PORT
A6
B6
A-PORT
A-PORT
A5
B5
A-PORT
A-PORTA4
B4
A-PORTA3
B3
A-PORTA2
B2
T
P
LS M
A-PORTA7
B7
58478
58478
58478
58478
58478
58478
58478
58478
58479
58478
58479
58479
4940
1
V1 V2
5828
4/58
285
D
58478
X3 X4
X1 X2
Fly-jib EXV:
Section - 6 56 26/180DL Hydraulics
26/180 - Manual # 99904617
Hydraulic Diagram - Stabilizer circuit – 2 fcts.
PstTst
A-PORT
A2 B2
A-PORT
A1 B1
5522
5
PT
5849
6
5849
6
Section - 6 57 26/180DL Hydraulics
26/180 - Manual # 99904617
Hydraulic Diagram - Stabilizer circuit – 4 fcts.
PstTst
D
C
5522
8
5849
6
5849
6
D
C
5522
8
A14 B14 A13 B13 A12 B12 A11 B11
5522
6 / 5
5281
PT
A-PORT A-PORT A-PORTA-PORT
Section - 6 58 26/180DL Hydraulics
26/180 - Manual # 99904617
Hydraulic Diagram - Stabilizer circuit – 4 fcts. RC
D
C
5522
8
5849
6
5849
6
D
C
5522
8
PstTst
A13 B13 A12 B12
5527
6
T
B-PORT
A-PORT
A11 B11
PA-PORT
B-PORT
NEM-MODULPT
T
ø1 mmø1 mm
50521
C1
C2
C3
D1
D2
D3
D4
C4
49187
49187
Only when HR stabilizer
Section - 6 59 26/180DL Hydraulics
26/180 - Manual # 99904617
Hydraulic Diagram - Stabilizer circuit – 4 fcts. + 4 available fcts.
D
C
5522
8
5849
6
5849
6
D
C
5522
8
Separate traverse
PstTst
A15 B15 A14 B14 A13 B13 A12 B12
5527
7
TA-PORT
B-PORT
A-PORTA-PORT
A11 B11
PA-PORT
OPT.
B-PORTB-PORTB-PORT
OPT.OPT.OPT.
ø1 mm ø1 mm
50521
C1
C2
C3
D1
D2
D3
D4
C4
Section - 6 60 26/180DL Hydraulics
26/180 - Manual # 99904617
Hydraulic Diagram - Stabilizer circuit – 4 fcts. + 4 available fcts. RC
D
C55
228
5849
6
5849
6
D
C
5522
8
Separate traverse
PstTst
P
P
A15 B15 A14 B14 A13 B13 A12 B12
5527
5
TA-PORT
B-PORT
A-PORTA-PORT
A11 B11
A-PORT
OPT.
B-PORTB-PORTB-PORT
OPT.OPT.OPT.
NEM-MODULT
T
ø1 mm ø1 mm
50521
C1
C2
C3
D1
D2
D3
D4
C4
Only when HR stabilizer
49187
49187
This page left intentionally blank
61
26/180 - Manual # 99904617
This page left intentionally blank
62
26/180 - Manual # 99904617
Section - 7 63 26/180SL - 26/180DL Dimension Drawings
26/180 - Manual # 99904617
Section - 726/180SL - 26/180DL Dimension Drawings
Section - 7 64 26/180SL - 26/180DL Dimension Drawings
26/180 - Manual # 99904617
Lifting capacity with winch
Hydraulic hoist type MAXW MAXWD1500 kg 3000 kg3305 lb
2500 kg 5000 kg5510 lb
Dinamic S 25Brevini 2500
Dinamic P9E
Dinamic P15E
3200 kg 6400 kg7050 lb
11020 lb
6610 lb
14100 lb
90°
0°
65°
Not recommended working angle.
Section - 7 65 26/180SL - 26/180DL Dimension Drawings
26/180 - Manual # 99904617
20/180SL - Dimension sketch
[mm] B C D EK2 4427 2690 2295 885K3 4503 2760 2295 885K4 4579 2800 2295 885K5 4655 2800 2295 885K6 4731 2800 2295 885K7 4807 2800 2295 995K8 4883 2800 2335 995
[in] B C D EK2 174.29 105.91 90.35 34.84K3 177.28 108.66 90.35 34.84K4 180.28 110.24 90.35 34.84K5 183.27 110.24 90.35 34.84K6 186.26 110.24 90.35 34.84K7 189.25 110.24 90.35 39.17K8 192.24 110.24 91.93 39.17
1.12
”(2
8.5)
2.87”(73)
49.21”(1250)
98.43”(2500)
15.98”(406)
39.57”(1005)
86.7
3”(2
203)
77.8
3”(1
977)
2.36
”(6
0)
C
B
D
E
TOP CHASSIS
A
A
A-A
TOP CHASSIS
TOP CHASSIS
Section - 7 66 26/180SL - 26/180DL Dimension Drawings
26/180 - Manual # 99904617
20/180DL - Dimension sketchC
D
B
CL CHASSIS
E
A
A
TOP CHASSIS
TOP CHASSIS TOP CHASSIS
A-A
1.12
”(2
8.5)
2.87”(73)
49.21”(1250)
11.42”(290)
98.43”(2500)
15.98”(406)
39.57”(1005)
86.7
3”(2
203)
77.8
3”(1
977)
2.36
”(6
0)
[mm] B C D EK2 4427 2690 2295 885K3 4503 2760 2295 885K4 4579 2800 2295 885K5 4655 2800 2295 885K6 4731 2800 2295 885K7 4807 2800 2295 995K8 4883 2800 2335 995
[in] B C D EK2 174.29 105.91 90.35 34.84K3 177.28 108.66 90.35 34.84K4 180.28 110.24 90.35 34.84K5 183.27 110.24 90.35 34.84K6 186.26 110.24 90.35 34.84K7 189.25 110.24 90.35 39.17K8 192.24 110.24 91.93 39.17
Section - 7 67 26/180SL - 26/180DL Dimension Drawings
26/180 - Manual # 99904617
20/180SL - Slewing Radius
11°
TOP CHASSIS
R 26.38”(R 670)
R 19.29”(R 490)
R 16.54”(R 420)
73.8
2”(1
875) 81.3
0”(2
065) 83.2
7”(2
115) 84.4
5”( 2
145)
96.2
6”( 2
445)
R 15.94”(R 405)
Section - 7 68 26/180SL - 26/180DL Dimension Drawings
26/180 - Manual # 99904617
20/180DL - Slewing Radius
13°
TOP CHASSIS
R 26.38”(R 670)
R 20.87”(R 530)
R 17.17”(R 436)
63.3
9”(1
610) 79.8
4”(2
028) 80.9
1”( 2
055) 84.4
9”( 2
146) 87.0
1”( 2
210) 96.2
6”(2
445)
R 15.94”(R 405)
Section - 7 69 26/180SL - 26/180DL Dimension Drawings
26/180 - Manual # 99904617
Dimension sketch for truck-mounted loader
Max. 1.26”(Max. 32)
Max. 1.26”(Max. 32)
Max. 6.29”
1.02”(26)
3.15
”(8
0)
7.28”
(Max. 160)
(185)
1.57
”(4
0)
29.6
5”(7
53)
14.8
8”(3
78)
Min. 22.91”
Max. 41.73”(Min. 582)
(Max. 1060)
14.8
8”(3
78)
Min. 35.43” / Max. 40.94”(Min.900 / Max.1040)
1.65”(42)
5.51”(140)
1)
Mounting kit 3 x M33x2 bolts + 1 x M30x2 bolts
Mounting kit 8 x M24x2 bolts
Notes:
1) Values dictated by strength considerations.
2) Drill hole when assembling
3) As regards installation - please see IMT Installation Manual
4) Mounting kits or spare parts - please see the Spare Parts Catalogue of the individual loader
See note 2)
1)1)
M30x2
CL CHASSIS
1.65”(42)
29.6
5”(7
53)
Section - 7 70 26/180SL - 26/180DL Dimension Drawings
26/180 - Manual # 99904617
20/180SL - Lifting height at column86
.61”
( 2.2
m)
R=39.37” (R=1m)
H1
TOP CHASSIS
H1 H1K2 2.74 m 107.87"K3 2.65 m 104.33"K4 2.56 m 100.79"K5 2.47 m 97.24"K6 2.38 m 93.70"K7 2.29 m 90.16"K8 2.21 m 87.01"
Section - 7 71 26/180SL - 26/180DL Dimension Drawings
26/180 - Manual # 99904617
20/180DL - Lifting height at column
H1
86.6
1”( 2
.2m
)
R=39.37” (R=1m)
TOP CHASSIS
H1 H1K2 2.74 m 107.87"K3 2.65 m 104.33"K4 2.56 m 100.79"K5 2.47 m 97.24"K6 2.38 m 93.70"K7 2.29 m 90.16"K8 2.21 m 87.01"
Section - 7 72 26/180SL - 26/180DL Dimension Drawings
26/180 - Manual # 99904617
Dimension sketch, fixed stabilizer legs
A 770mm 870mm 970mm
A 30.31” 34.25” 38.19”
11.42”(290)
CL CHASSIS
A20
.28”
(515
)
A
63.98” 91.54”
81.30”(2065)
81.30”(2065)
CL CHASSIS
254.1”(6455)
A
219.5”
(1625) (2325)
(5575)
A
219.5” / 254.1”(5575 / 6455)
26.4
2”17
.13”
(671
)(4
35)
TOP CHASSIS
Cylinder Stands, short
TOP CHASSIS
TOP CHASSIS
11.42”(290)
20.2
8”(5
15)
20.2
8”(5
15)
20.2
8”(5
15)
63.98”(1625)
91.54”(2325)
Section - 7 73 26/180SL - 26/180DL Dimension Drawings
26/180 - Manual # 99904617
Dimension sketch, fixed stabilizer legs
8.23
”
12.2
0”
12.8
7”15
” (209
)
(310
)
(372
)(3
81)
Section - 7 74 26/180SL - 26/180DL Dimension Drawings
26/180 - Manual # 99904617
Dimension sketch, swing-up stabilizer legs 20°- 60° (manual)
AA20
.39”
(518
)
219.06”
63.98”
81.30”
253.70”
(5564)
91.10”(2314)(1625)
(2065)
(6444)
A A
CL CHASSIS
CL CHASSIS
TOP CHASSIS
TOP CHASSIS
11.42”(290)
11.42”(290)
20.3
9”(5
18)
20.3
9”(5
18)
20.3
9”(5
18)
63.98”(1625)
91.10”(2314)
81.30”(2065)
Type R-20° (Obsolete)
Type R-60°
A
37.99”
37.68”
34.06”
33.74”
30.12”
29.80”
A
Type R-20° (Obsolete)
Type R-60°
A
965mm
957mm
865mm
857mm
765mm
757mm
A
Section - 7 75 26/180SL - 26/180DL Dimension Drawings
26/180 - Manual # 99904617
Dimension sketch, swing-up stabilizer legs 20°- 60° (manual)
C
B60°30° B
C
100
3.94”(100)
21°D
8.23”
12.20”
15” 14.65”
(209)
(310)
(381) (372)
Type R-20° (Obsolete)
Type R-60°
C
B
923mm
574mm
836mm
524mm
750mm
474mm
438mm402mm366mm
D
C
B
36.34”
22.60”
32.91”
20.63”
29.53”
18.66”
17.24”15.83”14.41”
D
Section - 7 76 26/180SL - 26/180DL Dimension Drawings
26/180 - Manual # 99904617
Dimension sketch, swing-up stabilizer legs 180° (manual + hydraulic)
A
B
CL CHASSIS
A16
.22”
(412
)
63.98” 91.34” 63.98”
219.3”
CL CHASSIS
91.34”81.30” 81.30”
135.8”
(1625) (2320) (1625)
(5570)
(2320)(2065) (2065)
(6450)
2.32
”(5
9)
AA
A
TOP CHASSIS
TOP CHASSIS
TOP CHASSIS
1.65
”2.
52”
(42)
(63)
11.42”(290)
16.2
2”(4
12)
16.2
2”(4
12)
16.2
2”(4
12)
11.42”(290)
A 34.45” 38.39” 42.32”
30.75” 34.69” 38.62”B
A 875mm 975mm 1075mm
781mm 881mm 981mmB
Section - 7 77 26/180SL - 26/180DL Dimension Drawings
26/180 - Manual # 99904617
Dimension sketch, swing-up stabilizer legs 180° (manual + hydraulic)
8.23
”
12.2
0”
14.6
5”15
” (209
)
(310
)
(372
)(3
81)
Section - 7 78 26/180SL - 26/180DL Dimension Drawings
26/180 - Manual # 99904617
Dimension sketch, TS - Top seat (RC)
R42
.91”
(R10
90)
R40
.55”
(R10
30)
(125
0)49
.21”
62.0
1”19
.29”
30.91”
34.25”19.09”
(785)
(870)(485)
93.5
0”
(157
5)(4
90)
(237
5)
Section - 7 79 26/180SL - 26/180DL Dimension Drawings
26/180 - Manual # 99904617
Dimension sketch, TS - Top seat (HC linear)
62.0
1”19
.29”
30.91”
34.25”19.09”
(785)
(870)(485)
93.3
1”
(157
5)(4
90)
(237
0)
R42
.91”
(R10
90)
R40
.55”
(R10
30)
2.44
”(6
2)
Section - 7 80 26/180SL - 26/180DL Dimension Drawings
26/180 - Manual # 99904617
Dimension sketch, TS - Top seat (Danfoss X)
62.0
1”19
.69”
32.87”
36.22”24.61”
(835)
(920)(625)
93.7
0”
(157
5)60
.24”
(153
0)(5
00)
(238
0)
R48
.03”
(R12
20)
R46
.06”
(R11
70)
0.78
”(2
0)
Section - 7 81 26/180SL - 26/180DL Dimension Drawings
26/180 - Manual # 99904617
Dimension sketch, TS - Top seat (HC X)
62.0
1”19
.69”
32.87”
36.22”24.61”
(835)
(920)(625)
93.7
0”
(157
5)54
.72”
(139
0)(5
00)
(238
0)
R48
.03”
(R12
20)
R46
.06”
(R11
70)
0.78
”(2
0)
Section - 7 82 26/180SL - 26/180DL Dimension Drawings
26/180 - Manual # 99904617
Dimension sketch, ladder for TS
20.4
7”48
.43”
(520
)(1
230)
TOP CHASSIS
Notes: 1) Ladder cannot be used for TS RC
2) There is no access to the top seat when the loader is in stowing position
Section - 7 83 26/180SL - 26/180DL Dimension Drawings
26/180 - Manual # 99904617
Technical data, winch
Performance (at 150 bar) 2176 psi: 1.5T winch 1.5T winch 2.5T winch 2.5T winch
Max. wire pull – 1st layer 1500 kg 3307 lb 2500 kg 5512 lbMax. wire pull – 2nd layer 1370 kg 3020 lb 2300 kg 5071 lbMax. wire pull – 3rd layer 1260 kg 2778 lb 2100 kg 4630 lbMax. wire pull – 4th layer 1170 kg 2579 lb 1950 kg 4299 lb
Wire speed (at 40 l/min.) 10.57 gpm: 1.5T winch 1.5T winch 2.5T winch 2.5T winch
Max. wire speed – 1st layer 22 m/min 72'2"/min 24 m/min 78'9"/minMax. wire speed – 2nd layer 24 m/min 78'9"/min 26 m/min 85'4"/minMax. wire speed – 3rd layer 26 m/min 85'4"/min 28 m/min 91'/minMax. wire speed – 4th layer 28 m/min 91'10"/min 30 m/min 98'5"/min
Weights: 1.5T winch 1.5T winch 2.5T winch 2.5T winch
Tare weight, winch (CE) 65 kg 143 lb 90 kg 198 lbFixed parts (valve section, brackets, hoses etc) 50 kg 110 lb 50 kg 110 lbWire Ø10 x 50 m 30 kg 66 lb 30 kg 66 lbSpare parts, single snatch block 30 kg 66 lb 30 kg 66 lbSpare parts, double snatch block 40 kg 88 lb 40 kg 88 lb
Section - 7 84 26/180SL - 26/180DL Dimension Drawings
26/180 - Manual # 99904617
Dimension sketch, winch
2.5T: 37.80”1.5T: 38.58”
(2.5T: 960)(1.5T: 980)
0.39”(10)
0.39”(10)
Section - 7 85 26/180SL - 26/180DL Dimension Drawings
26/180 - Manual # 99904617
Dimension sketch, stand-up platform (std.)
21.8
5”
71.6
5”(5
55)
(182
0)
TOP CHASSIS
Section - 7 86 26/180SL - 26/180DL Dimension Drawings
26/180 - Manual # 99904617
Dimension sketch, stand-up platform (valve control)
10.8
3”(2
75)
35.04”(890)
59.6
5”(1
515)
TOP CHASSIS
Section - 7 87 26/180SL - 26/180DL Dimension Drawings
26/180 - Manual # 99904617
Dimension sketch, internal hose routing
A
BøD
102.
1”(2
593)
øD A B A BK1, K2, K3 ø480 180mm 68mm 7.19” 2.68”
K4 ø520 200mm 48mm 7.87” 1.89”K5 ø570 225mm 23mm 8.86” 0.91”K6 ø620 250mm 2mm 9.84” 0.08”
Section - 7 88 26/180SL - 26/180DL Dimension Drawings
26/180 - Manual # 99904617
Dimension sketch, extra valves K7, K8
øD
A
B
2 EXV: 40.55”(2 EXV: 1030)
102.
1”(2
593)
øD A B A BK7 ø720 265mm 0mm 10.43” 0.00”
K8 ø720 265mm 0mm 10.43” 0.00”
Section - 7 89 26/180SL - 26/180DL Dimension Drawings
26/180 - Manual # 99904617
Stowed in truck body
93.8
6”
15°
98.9
4”
85.5
5”
53.3
1”
(238
4)
(251
3)
(217
3)
(135
4)
TOP CHASSIS
TOP CHASSIS
Section - 7 90 26/180SL - 26/180DL Dimension Drawings
26/180 - Manual # 99904617
20/180SL Center of Gravity
H2
V2 H1
f
H4
V2
V1
H3
V3
Z3
G2
G2
G1
G3CL CHASSIS
V1 V2 V3 H1 H2 H3 H4 Z3 f G1 G2 G326/180SL - K2 185 2075 760 145 2385 345 1690 20 290 870 1365 223526/180SL - K3 185 2115 785 145 3085 340 1865 40 290 870 1530 240026/180SL - K4 185 2150 810 145 3845 325 2020 55 290 870 1695 256526/180SL - K5 185 2175 830 145 4580 310 2115 75 290 870 1840 271026/180SL - K6 185 2195 845 145 5325 300 2210 85 290 870 1990 286026/180SL - K7 185 2210 865 145 5930 285 2280 100 290 870 2080 295026/180SL - K8 185 2225 880 145 6535 280 2350 110 290 870 2205 3075
V1 V2 V3 H1 H2 H3 H4 Z3 f G1 G2 G326/180SL - K2 7.28 81.69 29.92 5.71 93.90 13.58 66.54 0.79 11.42 1433 3009 492726/180SL - K3 7.28 83.27 30.91 5.71 121.46 13.39 73.43 1.57 11.42 1433 3373 529126/180SL - K4 7.28 84.65 31.89 5.71 151.38 12.80 79.53 2.17 11.42 1433 3737 565526/180SL - K5 7.28 85.63 32.68 5.71 180.31 12.20 83.27 2.95 11.42 1433 4057 597526/180SL - K6 7.28 86.42 33.27 5.71 209.65 11.81 87.01 3.35 11.42 1433 4387 630526/180SL - K7 7.28 87.01 34.06 5.71 233.46 11.22 89.76 3.94 11.42 1433 4586 650426/180SL - K8 7.28 87.60 34.65 5.71 257.28 11.02 92.52 4.33 11.42 1433 4861 6779
[mm] [kg]
[in] [lbs]
Section - 7 91 26/180SL - 26/180DL Dimension Drawings
26/180 - Manual # 99904617
20/180DL Center of Gravity
H2
V2 H1
f
H4
V2
V1
H3
Z3
V3
G2
G2
G1
CL CHASSIS G3
V1 V2 V3 H1 H2 H3 H4 Z3 f G1 G2 G326/180DL - K2 185 2065 795 145 2260 330 1600 20 290 870 1435 230526/180DL - K3 185 2105 820 145 2940 325 1770 35 290 870 1600 247026/180DL - K4 185 2140 840 145 3685 310 1930 55 290 870 1765 263526/180DL - K5 185 2165 855 145 4405 300 2030 70 290 870 1910 278026/180DL - K6 185 2185 870 145 5135 290 2125 85 290 870 2060 293026/180DL - K7 185 2195 890 145 5730 275 2200 95 290 870 2150 302026/180DL - K8 185 2210 905 145 6325 270 2270 105 290 870 2275 3145
V1 V2 V3 H1 H2 H3 H4 Z3 f G1 G2 G326/180DL - K2 7.28 81.30 31.30 5.71 88.98 12.99 62.99 0.79 11.42 1918 3164 508226/180DL - K3 7.28 82.87 32.28 5.71 115.75 12.80 69.69 1.38 11.42 1918 3527 544526/180DL - K4 7.28 84.25 33.07 5.71 145.08 12.20 75.98 2.17 11.42 1918 3891 580926/180DL - K5 7.28 85.24 33.66 5.71 173.43 11.81 79.92 2.76 11.42 1918 4211 612926/180DL - K6 7.28 86.02 34.25 5.71 202.17 11.42 83.66 3.35 11.42 1918 4387 646026/180DL - K7 7.28 86.42 35.04 5.71 225.59 10.83 86.61 3.74 11.42 1918 4740 665826/180DL - K8 7.28 87.01 35.63 5.71 249.02 10.63 89.37 4.13 11.42 1918 5016 6934
[mm] [kg]
[in] [lbs]
IMT reserves the right to make changes in engineering, design, specifications, add improvements or discontinue manufacturing at any time without notice or obligation.
IMT and IMT LOGO are registered trademarks of Iowa Mold Tooling Co., Inc., Garner, IA, USA.© 2017 Iowa Mold Tooling Co., Inc. All Right Reserved.
IOWA MOLD TOOLING CO., INC.
P.O. Box 189 Garner, IA 50438Tel: 641.923.3711
Fax: 641.923.2424www.imt.com