Upload
lyhanh
View
232
Download
4
Embed Size (px)
Citation preview
LLP™Turbine Bypass Valve for Low Pressure Bypass Applications
CC
I LLP™
Turb
ine B
ypass V
alve2
LLP™ delivers superior pressure reduction and temperature control, low noise and vibration, and fast response in a complete compact steam conditioning control valve.
Pressurized seat pilot plug assembly provides shutoff of an unbalanced plug with the low actuator force requirements of a balanced plug
The Compact Comprehensive Solution
The LLP™ by CCI is the leading low pressure turbine bypass valve for
combined cycle and process steam plants. The LLP™ is designed in both
angle and globe body configurations and easily fits into most existing
piping arrangements. The LLP™ may be installed in any orientation
without the need for additional support for the upper structure. Featuring
an integrated spring-loaded spraywater nozzle desuperheating manifold
at the valve outlet, the LLP™ minimizes the downstream desuperheating
distance, making it extremely compact for all types of low pressure
steam conditioning applications including advanced turbine bypass-to-
condenser applications with short pipe runs.
Spring-Loaded Nozzle Desuperheating
LLP™ desuperheating features integral spring-loaded water-injection
nozzles that optimize water-injection over a wide range of flow rates at low
pressures. With a rangeability of up to 50:1, the spring-loaded water-injection
nozzles vary the water flow as required to achieve the fine water droplet size
needed for atomization. The spring-loaded water-injection nozzle design
provides the smallest water droplet size possible without steam assist.
Pressurized Seat Pilot Plug Assembly
The LLP™ uses the CCI Pressurized Seat Pilot Plug Assembly to provide
repeatable ANSI/FCI 70-2 Class V Shutoff as a standard feature.
The design features a pilot and main plug, and a piston ring balance seal.
The piston ring allows a small, controlled leak of pressure from the valve
inlet to the bonnet cavity. When the control valve is closed and the pilot
plug is seated, the piston ring allows controlled shutoff pressure to build in
the bonnet cavity above the plug, acting to close the valve and providing
exceptional shutoff. With the CCI Pressurized Seat Pilot Plug Assembly, the
actuator only needs to provide sufficient thrust to seat the pilot plug against
the pilot seat in the main plug.
When a signal to open the control valve is received, the actuator lifts the
stem, opening the pilot seat. The pilot rapidly exhausts the bonnet cavity
pressure, and the plug assembly is now balanced. As the stem continues
to move in the opening direction, the shoulder on the stem engages the
retaining plate on the main plug, which lifts the main plug off the main seat.
The actuator only needs to provide sufficient thrust to lift the balanced plug.
Water-injection nozzle provides smallest water droplet size possible
Good atomization at wide range of flow rates
CC
I LLP™
Turb
ine B
ypass V
alve
Highly reliable, fast, accurate pneumatic and hydraulic actuators provide superior system control.
Table 1: Factors Influencing Actuator Selection
3
Accurate Control
CCI’s long history of developing advanced technology valves and actuation
systems for severe service and safety-related applications has led to the
development of the most reliable actuation systems available today. CCI has
supplied pneumatic and hydraulic actuation systems for over 30 years and
has an extensive installed global base. Our pneumatic actuation systems can
deliver stroke speeds of less than one second while maintaining accurate
resolution and control.
The selection of pneumatic or hydraulic actuation is primarily a function of
valve design for the particular application as well as customer preference. A
comparison of the factors influencing actuator selection is given in Table 1.
Improve Plant Efficiency—Eliminate Lost Steam
During normal operation, any leakage past a turbine bypass valve means lost
revenue.
g Steam that does not go through the turbine does not generate electricity or
revenue for the plant.
g Money spent generating the steam is lost.
g Steam leaking past a valve seat could erode the seat and cause an increase
in the leakage rate and maintenance downtime.
g Steam leaking past a valve to condenser could reduce the efficiency of the
condenser by deteriorating the vacuum and raising the condenser temperature.
The CCI LLP™ Turbine Bypass Valve comes standard with a pilot trim designed
for ANSI/FCI 70-2 Class V Shutoff, providing dependable, repeatable shutoff and
exceptional seat tightness for long periods of time with high pressure differentials.
etubirttAecnamrofreP citamuenPICCrotautcAmgarhpaiD rotautcAciluardyHICC
deepSekortSedoMpirTrofdnoceS1nahTsseL,tsaF
noitaludoMrofsdnoceS01nahTsseLsdnoceS5.0nahTsseL,tsaFyreV
noituloseR %1nahTsseL,dooG %1.0nahTsseL,dooGyreV
tsurhTdezirusserProfstnemeriuqeRtsurhTsteeM
sevlaVtaeSrofstnemeriuqeRtsurhTsteeM
sevlaVdecnalabnU
ytilibaileR tsuboRdnaelbaileRyreV tsuboRdnaelbaileRyreV
tsoCtnemerucorP evisnepxenI tsoCrehgiH
tsoCnoitallatsnI evisnepxenI tsoCrehgiH
ecnanetniaM sllikSmuideMhtiW,ysaE ecnanetniaMrofsllikSrehgiHseriuqeR
stnenopmoC seirosseccAelbaileR,erusserPwoL seirosseccAlaicepS,erusserPhgiH
CC
I LLP™
Turb
ine B
ypass V
alve
Top Entry Design
Minimizes service time.
Option of Open Port or Low Noise Small- Drilled-Hole Cage Trim
Globe Body Configuration Optional
Pressurized Seat Pilot Plug Design
Provides Class V Shutoff.
Spraywater Manifold System
Multiple attemperation injection points with single
customer water connection.
Spring-Loaded Spraywater Nozzle Desuperheaters
Mounted directly to outlet, eliminating need for
additional piping sections.
Superior Atomization
Valve Performance Characteristics (% Cv vs. % Stroke)Valves are custom characterized to accommodate a wide range of variables.
Linear Modified Equal Percentage Equal Percentage
4
No trim parts are welded or screwed into the valve body
Low Noise Small-Drilled-Holed Cage
Reduces noise level to below 85 dBA
CC
I LLP™
Turb
ine B
ypass V
alve
Use this checklist to evaluate the benefits of the LLP™ design.
5
CC
I LLP™
Turb
ine B
ypass V
alve
A custom solution based on 40 years of experience.
mirTeziS
noitarugifnoCydoBnoitcennoCdnE&
epiptelnI)hcni(
epipteltuO)hcni( A *A B C D E *E
8 dnEdleW,elgnA 01,8 21,019.31)353(
—6.31)543(
5.21)023(
6.7)091(
83)079(
84)0221(
01 dnEdleW,elgnA 41,21 61,412.61)114(
—3.41)363(
0.41)063(
2.8)012(
04)0201(
05)0721(
8 dnEdleW,ebolG 8 80.33)838(
0.42)016(
— — —73
)049(74
)0911(
01 dnEdleW,ebolG 01 010.93)199(
0.03)267(
— — —93
)099(94
)0421(
8 egnalFFR,ebolG 7 8 8 6etoN0.42)016(
— — —73
)049(74
)0911(
01 egnalFFR,ebolG 7 01 01 6etoN0.03)267(
— — —93
)099(94
)0421(
1. All dimensions are in inches except ( ) are in millimeters.2. Dimension A is for valves with spray nozzles, and dimension A* is for valves without spray nozzles.3. Dimension E* is for a hydraulic actuator.4. Buttweld per ANSI B16.25 and mating pipe schedule.5. Valve may be installed in any orientation. The upper structure does not require additional support.6. Per customer design requirements.7. ANSI 600# RF flange.
Table 2: Dimensional Information
6
Angle Configuration Globe Configuration
CC
I LLP™
Turb
ine B
ypass V
alve
Technical specifications and materials.
1. Rangeability may vary with process conditions. Consult with factory.
2. Hydraulic actuator available upon request.
)hcni(eziSepiP dna02rednU 04ot02
maetSdetarutaS
epiPleetSnobraCotecnatsiD )2.1(4 )5.2(8
dneBtsriFotecnatsiD * *
eborPerutarepmeTotecnatsiD ** **
taehrepuSC41/F52
epiPleetSnobraCotecnatsiD )2.1(4 )5.2(8
dneBtsriFotecnatsiD )5.2(8 )5.3(21
eborPerutarepmeTotecnatsiD )5.5(81 )01(33
taehrepuSC38/F051
epiPleetSnobraCotecnatsiD )2.1(4 )5.2(8
dneBtsriFotecnatsiD )2(6 )3(01
eborPerutarepmeTotecnatsiD )5(61 )5.9(13
1. Alternate materials available per customer’s specific design requirements.
* With saturated steam, to avoid pipe erosion and liquid drop-out due to droplet impingement, bends should be avoided.
** Saturated steam conditions cannot be controlled through downstream temperature measurement. Feed-forward/enthalpy control recommended.
† All dimensions are in feet except ( ) are in meters.
Table 4: Capacity and Performance Data
Table 3: Materials Table 5: Recommended Desuperheating Lengths Using Spring-Loaded Nozzles
7
tnenopmoC metI.oN
foslairetaMnoitcurtsnoC
ydoB 1 BCW-612A 1
tennoB 2 BCW-612A 1
egaC 3seireS004
leetSsselniatS
gulPniaM 4seireS004
leetSsselniatS
gulPtoliP 5seireS004
leetSsselniatS
metS 6seireS004
leetSsselniatS
gniRtaeS 7seireS003
leetSsselniatS
DRAG is a registered trademark of CCI.©2002 CCI 387 3/02 3M
Contact us at:[email protected]
Visit us online at:www.ccivalve.com
CCI World Headquarters—CaliforniaTelephone: (949) 858-1877Fax: (949) 858-187822591 Avenida EmpresaRancho Santa Margarita,California 92688 USA
CCI Switzerland formerly Sulzer ThermtecTelephone: 41 52 264 95 00Fax: 41 52 264 95 01Im Link 11, P.O. Box 65CH-8404 WinterthurSwitzerland
CCI KoreaTelephone: 82 31 985 9430Fax: 82 31 985 055226-17, Pungmu-DongKimpo City, Kyunggi-Do 415-070South Korea
Throughout the world, companies rely on CCI to solve their severe service control valve problems. CCI has provided custom solutions for these and other industry applications for more than 40 years.
CCI JapanTelephone: 81 726 41 7197Fax: 81 726 41 71984-15-20 ShukunoshoIbaraki-City, Osaka 567-0051Japan
CCI Sweden (BTG Valves)Telephone: 46 533 689 600Fax: 46 533 689 601Box 603SE-661 29 SäffleSweden
CCI Austriaformerly Spectris Components GmbHTelephone: 43 1 869 27 40 Fax: 43 1 865 36 03Lembockgasse 63, 1230 Wien1233 ViennaAustria
Sales and service locations worldwide.