69977 OP100 OC100 Spare Parts Manual 4AE

Orthopantomograph®

OP100Orthoceph®

OC100Spare Part Manual

2003 69977

Copyright Code: 69977-4AE Date: 10/2003

© 2003 by Instrumentarium Imaging

Documentation, trademark and the software are copyrighted with all rightsreserved. Under the copyright laws the documentation may not be copied,photocopied, reproduced, translated, or reduced to any electronic medium ormachine readable form in whole or part, without the prior written permissionof Instrumentarium Imaging.

Orthopantomograph® and Orthoceph® are registered trademarks ofInstrumentarium Corporation. U.S. patents 4,641,336; 5,016,264; 5,425,065and 5,444,754. German patent 4,344,745. Orthopantomograph® OP 100 andOrthoceph® OC100 comply with UL and C-UL (File E157261).

The original language of this manual is English.

Instrumentarium Imaging reserves the right to revise this publication fromtime to time and to make changes in the content of it without obligation tonotify any person of such revision or changes.

Manufactured by Instrumentarium Imaging

P.O. Box 20FIN-04301 TuusulaFINLANDTel. +358 10 394 6500Fax. +358 10 394 6501E-mail: [email protected]: http://www.InstrumentariumImaging.com

69977-4AE Instrumentarium Imaging 5

Table of Contents

1 Introduction ......................................................................................................... 1

2 Main assemblies................................................................................................... 3

3 Column unit ......................................................................................................... 53.1 OP 100 column std & short, complete ......................................................................... 6

3.2 OC100 column std & short, complete.......................................................................... 73.3 OP 100 Column assembly, standard & short ............................................................... 8

3.3.1 Suspension plate assembly ........................................................................................ 103.3.2 Sliding carriage assembly.......................................................................................... 123.3.2.1 Wheel assembly long, Units s/n 70000 - 70999 ...................................................................143.3.2.2 Wheel assembly, short, Units s/n 70000 - 70999..................................................................15

3.3.2.3 Wheel assembly, Units s/n 71000 and up ............................................................................. 16

3.3.3 Counter weight complete........................................................................................... 183.3.4 Rear support assembly............................................................................................... 193.3.5 Counter weight locking ............................................................................................. 203.3.6 Mains cord................................................................................................................. 21

3.4 Remote exposure button............................................................................................. 243.5 OP100 Base plate (old model) ................................................................................... 243.6 OC100 Base plate (old model)................................................................................... 26

4 Rotating unit/ carriage assembly ..................................................................... 294.1 Chassis assembly........................................................................................................ 324.2 FH projector assembly ............................................................................................... 344.3 Mid-sagittal projector assembly................................................................................. 354.4 Bottom plate assembly ............................................................................................... 364.5 Carriage left side ........................................................................................................ 38

4.6 Carriage right side...................................................................................................... 404.7 Control panel assembly.............................................................................................. 424.8 Main support .............................................................................................................. 43

4.8.1 Sliding chassis assembly ........................................................................................... 454.8.2 Rotation switch assembly .......................................................................................... 464.8.3 Sliding plate assembly............................................................................................... 47

4.8.4 Linear transmission assembly.................................................................................... 484.8.5 Linear motor assembly .............................................................................................. 49

4.9 Head support holder, IEC cover, cable holders ......................................................... 504.10 Lower shelf assembly............................................................................................... 55

5 Rotating unit ...................................................................................................... 575.1 Rotating unit cast, units s/n 70000-70999.................................................................. 58

5.1.1 Rotating unit drive motor assembly, units s/n 70000-70999..................................... 595.1.2 Rotating unit cast, from unit s/n 71000-.................................................................... 60

5.2 Head support, unit’s s/n 70000-70240 ....................................................................... 625.3 Head support, units s/n 70241- 71360 ....................................................................... 635.4 Head support, units 71308, 71358 and from unit s/n 71361...................................... 65

5.4.1 Hair cover, units s/n 70000-70240 ............................................................................ 67

5.4.2 Hair cover, from unit s/n 70241 ................................................................................ 675.5 Generator assembly.................................................................................................... 68

5.5.1 Tube head assembly, Inverter & Filament Boards .................................................... 685.5.2 Collimator assembly.................................................................................................. 705.5.2.1 Collimator OP100, units s/n 70000-70271 ........................................................................... 705.5.2.2 Collimator OP1 00, units s/n 70272-70608 ..........................................................................71

ii Instrumentarium Imaging 69977-6AE

5.5.2.3 Collimator OP100, units from s/n 70609 ..............................................................................72

5.5.2.4Collimator OC100 M, JT, units s/n 70000-70559..................................................................735.5.2.5 OC100 Inch, JT, Japan Collimator, units s/n 70000-70559 ..................................................745.5.2.6OC100, M, JT, collimator, from unit s/n 70581.....................................................................765.5.2.7OC100, JT, collimator, (8x10, 10x12) inch, Japan, from unit s/n 70714 ...............................78

5.5.2.8 Collimator, OC100, JT, (8x10SV/AV, 10x8AH) in, USA, from s/n 70458..........................805.5.2.9 Collimator, OP100 OT ..........................................................................................................825.5.2.1 0Collimator, OC1 00 OT.......................................................................................................84

5.6 Cassette rack ............................................................................................................... 875.6.1 Cassette rack, units s/n 70000-70231......................................................................... 87

5.6.2 Cassette rack, from unit s/n 70232............................................................................. 895.6.3 Cassette rack, from unit s/n 70232............................................................................. 905.6.4 Cassette rack, OP/OC100 CR .................................................................................... 92

5.7 AEC Board ................................................................................................................. 935.8 Cassette lifting assembly ............................................................................................ 945.9 Cephalostat lock assembly ......................................................................................... 95

6 Cephalostat .........................................................................................................976.1 Cephalostat assembly, units s/n 70000-7005 1........................................................... 986.2 Cephalostat assembly, units s/n 70052-71437.......................................................... 1006.3 Cephalostat assembly units s/n 80052-71437........................................................... 1026.4 Cephalostat assembly units, s/n 71438-72263.......................................................... 1036.5 Cephalostat assembly, units from s/n 72264 ............................................................ 1056.6 Cephalostat cardboard box packing, from s/n 71617 ............................................... 1076.7 Ear holder, 4-holes................................................................................................... 1086.8 Installation accessories ............................................................................................ 108

6.8.1 Up to s/n 72370........................................................................................................ 108

6.8.2 From s/n 72371 ....................................................................................................... 1106.9 Patient positioning accessories ................................................................................ 110

7 Patient positioning accessories ...................................................................... 111

8 Electrical spare parts ......................................................................................1138.1 Printed circuit boards................................................................................................ 1138.2 Connectors ............................................................................................................... 1158.3 Transformers & cable sets ....................................................................................... 1168.4 Micro switches, light bulbs and fuses...................................................................... 1198.5 CPU software............................................................................................................ 120

8.6 Software & board version references ....................................................................... 121

9 Service tools ......................................................................................................123

10 Recommended spare parts ............................................................................. 12910.1 Spare part kits ........................................................................................................ 12910.2 Spare part minikit, units s/n 72000 and up.SW 1.2.07 and up. ............................. 13510.3 Ortho Trans spare part kits ................................................................................... 135

10.4 Screws and washers for OP100 covers................................................................... 13810.5 Colors ..................................................................................................................... 140

11Ortho Trans units & upgrade kit parts ............................................................ 141

12 Fan Kit .............................................................................................................. 14712.1 Boxes ...................................................................................................................... 148


7 Introduction

1 IntroductionCodes

Please specify the product code when placing orders. The quantity will be each, unless otherwise indicated.The “Qty” paragraph in this manual indicates how many respective parts are used in the assembly.

If the correct spare part cannot be identified, please contact Instrumentarium Imaging Technical ServiceDepartment. The information about the product model, assembly and the serial number of the product orassembly may be useful and will make the spare part order handling faster and more reliable.

Product codes with asterisk “*”, eg. “*12345” are such that need not to be stocked or they are part of anotherassembly.

Upgrades

Old units can be updated beyond our knowledge. After update if spare parts are needed the person who isresponsible for repair must specify which is the correct part. Instrumentarium Imaging Technical Departmentwill assist, when needed.

Price list

Spare Parts Price Lists will be issued under separate cover.


8 Introduction


9 Main assemblies

2 Main assemblies

Pos Description See section

1 Column 3

2 Rotating unit/Vertical carriage 4

3 – Main support 4.84 – Lower shelf 4.10

5 Rotating unit 5

6 – Head support assembly 5.27 –Generator assembly 5.38 – Collimator assembly 5.3.29 – Cassette rack assembly 5.4

10 Cephalostat 6

Patient positioning accessories 7

Electrical parts 8

Service tools 9

Recommended spare parts 10

Ortho trans units & upgrade kits 11

OP100 Fan Kit 12

10 5

4 6

9 3

2

7

1

8


10 Main assemblies


3 Column unit

3 Column unit

1

3

2

12 Instrumentarium Imaging 69977-4AE

7

5

4


3 Column unit

Pos Code Description Unit s/n Note

1 60489 OP100 Column std, compl. Eur 70000-70999 See section 3.1

1 60491 OP100 Column std, compl. USA 70000-70999 See section 3.1

1 60492 OP100 Column short, compl. Eur 70000-70999 See section 3.1

1 60493 OP100 Column short, compl. Japan 70000-70999 See section 3.1

1 60494 OC100 Column std. compl. Eur 70000-70999 See section 3.2

1 60490 OC100 Column std. compl. USA 70000-70999 See section 3.2

1 60488 OC100 Column short, compl. Eur 70000-70999 See section 3.2

1 60450 OC100 Column short, compl. Japan 70000-70999 See section 3.2

1 60547 OP100 Column std, MK2 compl. Eur 71000- See section 3.1

1 60549 OP100 Column std, MK2 compl. USA 71000- See section 3.1

1 60513 OP100 Column short, MK2 cmopl. Eur 71000- See section 3.1

1 60550 OP100 Column short, MK2 cmopl. Japan 71000- See section 3.1

1 60512 OC100 Column std, MK2 compl. Eur 71000- See section 3.2

1 60548 OC100 Column std, MK2 compl. USA 71000- See section 3.2

1 60559 OC100 Column short, MK2 compl. Eur 71000- See section 3.2

1 60546 OC100 Column short, MK2 compl. Japan 71000- See section 3.2

2 60300 Wall mount assembly See section 3.4

2 60517 Wall mount assembly USA See section 3.4

3 69961 Remote exposure button, compl. See section 3.5

4 60280 OP 100 Base plate See section 3.6

60582 OP 100 Base plate II See section 3.6

5 60440 OC100 Base plate See section 3.7

60583 OC100 Base plate II See section 3.7


3 Column unit

Pos Code Description Unit s/n Note

6 60338 Chair adapter See section 3.8

7 Mains cord See section 3.3.6

3.1 OP100 column std & short, complete

Pos Code Description Qty Note

1 - 4 60489 OP 100 Column std, compl. Eur 1 70000-70999

1 - 4 60547 OP100 Column std, MK2 compl.Eur 1 71000-

2 60420 Trim Weight Set OP 100 1

3 60487 Mains cord Eur 1

4 60497 Wooden crate 1

1 - 4 60491 OP100 Column std, compl. USA 1 70000-70999

1 - 4 60549 OP100 Column std, MK2 compl.USA 1 71000-


3 60486 Mains cord USA, 220 V 1


1 - 4 60492 OP 100 Column short, compl.Eur 1 70000-70999

1 - 4 60513 OP100 Column short, MK2 compl.Eur 1 7 1000-




1 - 4 60493 OP 100 Column short, compl. Japan 1 70000-70999

1 - 4 60550 OP100 Column short,MK2 comp. Japan 1 71000-


3 60486 Mains cord Japan 1


4 60495 Cardboard box 1

3

1

2


3 Column unit

3.2 OC100 column std & short, complete


1 - 4 60494 OC100 Column std. compl. Eur 1 70000-70999

1 - 4 60512 OC100 Column std.MK2 compl.Eur 1 7 1000-

2 60425 Trim Weight Set OC100 1



1 - 4 60490 OC100 Column std. compl. USA 1 70000-70999

1 - 4 60548 OC100 Column std.MK2 compl.USA 1 71000-





21495 Cable USA and Japan 1

1 - 4 60488 OC100 Column short, compl. Eur 1 70000-70999

1 - 4 60559 OC100 Column short,MK2 compl.Eur 1 71000-




1 - 4 60450 OC100 Column short, compl. Japan 1 70000-70999

1 - 4 60546 OC 100 Column short,MK2 compl.Japan 1 71000-

3 60496 Mains cord Japan 1



4 60495 Cardboard box 1

3

1

2

3 Column unit


3.3 OP100 Column assembly, standard & short


1 - 81 60250 OP 100 Column Assembly, standard See note 6

Units s/n 70000 - 70999

Units from s/n 71000 -


3 Column unit


1 - 81 60355 OP 100 Column Assembly, short See note 6

1 - 81 60547 OP 100 Column Assembly, MK2,standard See note 7

1 - 81 60550 OP 100 Column Assembly, short,MK2,Japan See note 7

1 60260 Suspension Plate Assembly 1

2 *60479 Top Bumper Assembly 1

3 *60270 Sliding Carriage Assembly 1 See note 6

3 *605 10 Sliding Carriage Assembly MK2 1 See note 7

4 *60330 Rear Support Assembly 1 See note 6

4 *60511 Rear Support Assembly MK2 1 See note 7

5 *60265 Counter Weight Assembly 1 See note 1

6 60402 Counter Weight Locking M1 0 Assembly 1 See note 2

6 60541 Counter Weight Locking M16 Assembly 1 See note 5

8 *60401 Column Base Plate Assembly 1

9 *60256 Column, standard (L = 2200 mm) 1 See note 3

9 60677 Column, standard (L2200 mm) 1 Note 8

9 *60326 Column, short (L = 2110 mm) 1 See note 4

10 *60303 Code bar long 1

11 *60302 Code bar short 2

12 3264 Allen screw M4 x 16 6

15 *M60288 Column hatch 1

16 21443 Allen screw M4 x4 4

17 3588 Locking ring 4.3 4

20 21421 Screw 2

51 60277 Counterweight cable, std 2 See note 3

51 60327 Counterweight cable, short 2 See note 4

52 328 Nut M8 2

53 335 Washer 8.4A 2

54 *M60298 Strain relief plate R 1

55 *M60299 Strain relief plate L 1

57 *60261 Mount bar 8 mm x 25 mm 1 From s/n 76809 narrowedfrom 25 to 20 mm.

58 4324 Screw M8 x 20 2

59 *69945 Sticker for X 103 1

60 *69944 Sticker for X 100 1

61 21187 Screw M3 x 18 4

62 *20070 Socket 2

63 321 Screw M4 x 6 4

64 60332 Strain relief 2

75 60362 Screw M8 4

76 61171 Trim cover R 1

61222 Trim cover R 1 See note 7

3 Column unit



77 61172 Trim cover L 1

61225 Trim cover L 1 See note 7

78 21443 Screw M4 6 See note 7

79 4291 Washer 4,2 6 See note 7

80 2740 Screw 6 See note 6

81 21402 Plastic cap 6 See note 6

Note 1: Trim weight sets OP 100 and OC 100 have their own assembly codes.

Note 2: All models from s/n 70150.

Note 3: Used in the standard column assembly code 60250.

Note 4: Used in the short column assembly (code 60335), which is 90 mm shorter than the standard columnassembly (code 60250).

Note 5: From s/n 71075 (summer 1994) Security bolt M16 in all units.

Note 6: Units s/n 70000 - 70999

Note 7: Units from s/n 71000 -

Note 8: From s/n 75892 installation height lower. (100 mm)

3.3.1 Suspension plate assembly


3 Column unit


1 - 23 60260 Suspension plate, complete

1 60284 Suspension plate 1

2 60481 Pulley assembly 1

3 5241 Screw M12 x 40 1

4 60480 Vertical Motor Clutch Assembly 1

5 *30038 Motor chassis 1

6 60575 Vertical (Z) Motor M1(20007) assembly 1

7 20319 Rubber bushing 2

8 31024 Motor bushing 2

9 295 Screw M6 x 16 4

10 2395 Washer 6.4 4

11 293 Screw M6 x 20 4

12 9354 Ball bearing 2

13 2754 Screw M4 x 8 4

14 3588 Washer 4.3 8

15 *60259 Side plate, left 2

60711 Side plate, right 1 From s/n 76996

16 *603 19 Holder 2

17 60274 Drive bolt 1

18 60263 Pulley w/friction ring 1

19 60315 Sliding ring 1

20 3587 Spring 4

21 60313 Washer 1

22 5477 Nut M8 Nyloc 1

23 21443 Screw M4x8 4

3 Column unit


3.3.2 Sliding carriage assembly


1 - 31 60270 Sliding carriage, complete Units 70000 - 70999

1 60286 Sliding carriage 1

2 60485 Wheel Assembly, Long 2

3 60484 Wheel Assembly, Short 2

4 60458 Adjustment shims set 2 See note 1

5 61191 Carriage end guide L 1 See note 2

6 61192 Carriage end guide R 1 See note 2

7 3202 Screw M3 x 8 8 See note 2

8 60461 Axle 3

9 60453 axle 1

10 60340 Cable trim cover R 1

11 60339 Cable trim cover L 1

12 3588 Washer 4.3A 2

13 2754 Screw M4 x 8 2

14 21421 Screw M8 x 20 4

15 2396 Washer 8.4 4

16 2740 Screw M4 x 6 2 See note 3

17 21402 Plastic cap M4 2 See note 3

30 68971 Cable SC 1 (Power) 1

31 68972 Cable SC 2 (Remote/Z-motor) 1


3 Column unit

Note 1: This kit contains 0.3, 0.5 and 1.0 mm trim shims to adjust the space between the sliding carriage,column assembly and wheel assembly.

Note 2: Used with models equipped with the One Man Installation Kit (code 60325)

Note 3: Units s/n 70000 - 70999, Plastic cap + screw for Trim covers.


1 - 23 60510 Sliding carriage MK2, complete. Units from s/n 7 1000-

1 60557 Side wheel assembly 4

2 60465 Axle 1

3 60482 Wheel assembly 2

4 60466 Bushing 2

5 68972 Cable SC2 1

6 60454 Bushing 2


8 60461 Axle 2


10 60462 Bushing 2

11 60453 Axle 2

13 60460 Side holder 2

14 60454 Sliding carriage 1 See note 1

15 60501 Cable holder 2

16 21585 Screw M4x40 4

17 68971 Cable SC1 1

18 60340 Cable trim cover R 1

19 60339 Cable trim cover L 1

20 2754 Screw M4x8 2

2

16

1

5

3

4

19

18

6

13

8

20 21

7

14

9 10 11

1 6 2 2 2 3

17

15

3 Column unit



21 3588 Washer 2

22 4291 Washer 4

23 3588 Washer 4

Note 1: From s/n 72869 the matching holes for carriage fixing “opened”.

3.3.2.1 Wheel assembly long, Units s/n 70000 - 70999


1 - 12 60485 Wheel assembly long, complete

1 *60279 Wheel chassis, long 1

2 60482 Carriage guide wheel ∅ 70 2

3 321 Allen screw M4x6 1

4 60344 Axle pin/screw ∅ 12 2

5 60481 Pulley assembly 1

6 60483 Guide wheel ∅ 30 1

7 60262 Axle pin ∅ 10 1

8 *60264 Counterweight cable guide 2

9 3588 Washer 4.3 2

10 2754 Screw M4x8 2

11 60342 Bushing 2

12 60343 Bushing 1


3 Column unit

3.3.2.2 Wheel assembly, short, Units s/n 70000 - 70999


1 - 12 60484 Wheel assembly Short, complete

1 *60278 Wheel chassis, short 1



4 60344 Axle pin/screw ∅ 12 1

5 60483 Guide wheel ∅ 30 1

6 60262 Axle pin ∅ 10 1

7 4262 Screw 2

8 60258 Strain relief mount 2 1

9 60342 Bushing 1

10 60343 Bushing 1

11 2396 Washer 8.4 4

12 21421 Screw M8x20 4

3 Column unit


3.3.2.3 Wheel assembly, Units s/n 71000 and up


60557 Side wheel 4

1 60453 Housing 1

2 60459 Axle 1

3 60474 Wheel 1

6603 Bearing 24

2

1

3

Pos


3 Column unit

Code Description Qty Note

60481 Cable pulley 2

1 60266 Pulley 1

2 9354 Bearing 1

3 60453 Axle 1


60482 Pulley 4

1 60287 Pulley 1

2 9354 Bearing 1

2

1

3 Column unit


Pos Code DescriptionQty Note

1=2-11 *6026 5 Counterweight assembly See note 1

2 293 Screw M6x20 12

3 334 Washer 6.4B 12

4 335 Washer 8.4A 2

5 5150 Bolt M10x30 1

6 21421 Bolt M8x20 1

7 328 Nut M8 2

8 60267 Limiter 10x20 2

9 60268 Sliding guide 10x16 2

10 60282 Counterweight 1

10 60554 Counterweight 1 See note 3

11 60294 Rocker bar 1

20=2-25 *60420 Trim weight Set OP 100 See note 2

21 5477 Nut M8 Nyloc 2

22 3242 Washer 2

23 60331 Trim weight 2: 0,7 kg 7

24 60329 Trim weight: 0,37 kg 4

25 60421 M8 threaded bar L=85 2 See note 1

30=3-39 *60425 Trim Weight Set OC100

31 60422 M8 threaded bar L= 175 2 See note 2

32 60329 Trim weight: 0,37 kg 4

33 60331 Trim weight 2: 0,7 kg 23

34 60419 Steel plate 1

35 60267 Limiter 1

3.3.3 Counter weight complete

37 38

39

36

33

32

31

34

35

23

21

22

24

25

3020

11


3 Column unit


36 328 Nut 2

37 293 Screw 2

38 334 Washer 2

39 60268 Sliding guide 1

Note 1: Counter weight complete requires one of the trim weight sets.

Note 2: All models up to s/n 70178 use one M6 threaded bar to support trim weights.

Note 3: From unit s/n 71075 (security bolt M16)

Note 4: Base plates added for wire cables from s/n 76155.

3.3.4 Rear support assembly


1 - 13 *60330 Rear support, compl. Units s/n 70000-70999

*60511 Rear support MK2 complete. Units from s/n 71000-

1 *60336 Rear support 1 Note 1

60475 Rear support 1 Note 2

60584 Rear support 1 Note 4

2 *21322 Screw M8x25 2 Note 1

3 *21322 Screw M8x20 2 Note1

4 *2740 Screw M4x6 2 Note 1

5 21402 Plastic cap M4 2 Note 1

6 4260 Screw M2x12 4

7 4291 Washer 4.3B 4

8 68959 Cable C8 (X117) 1

9 20014 Micro switch AH 3862619K 2

13

9

10

11

12

8

2

4

5

2

1

7

6

15 16

17

18

3 Column unit



10 *60335 Micro chassis R 1

11 *603 34 Micro switch L 1

12 *62033 Nut plate 2

13 21481 Screw 4

15 2395 Washer 2 Note 3

16 3689 Screw M6x25 2 Note 3

17 6481 Adjusting support 1 Note 3

18 301 Screw M8x25 1 Note 3

Note 1: Units s/n 70000 - 70999

Note 2: Units from s/n 71000 - 71662

note 3: parts needed only for Cephalostat unit’s s/n 70000 - 71500 and from unit’s s/n

72264 Note 4: From unit s/n 71663

3.3.5 Counter weight locking


1 - 7 60402 Counter weight Locking M1 0, complete

1 61198 Transportation plate 1 See note 2

61356 Transportation plate 1 Note 5

2 335 Washer 8.4A 9

3 2676 Screw M8 x 16 3

4 534 Washer 8.4A 3

5 60541 Security bolt 1 Note 6

5 60363 Security bolt M10 1 See note3

5a 21406 bolt 1 See note 4

5b 60311 Bushing 1 See note 4

6 60364 Felt washer 1

7

6

51

2

4

3


3 Column unit


7 60328 Trim plug 1 See note 4

7 21189 Trim plug∅ 20 / 25 1

1 - 7 60542 Counter Weight Locking M16, complete See note 1

1 61198 Transportation plate 1

2 335 Washer 8.4A 9

3 2676 Screw M8x16 3

4 534 Washer 8.4A 3

5 60541 Security bolt M16 1

6 60364 Felt washer 1

7 21189 Trim plug ∅ 20 / 25 1

Note 1: From s/n 71075 Security bolt M16 in all units.

Note 2: Security bolt will be mounted upside down with the column assembly short.

Note 3: Equipped from s/n 70150.

note 4: Units s/n 70000 - 70149 a bushing and a bolt were used.

Note 5: From unit s/n 75234 with standard column (2200 mm).

Note 6: January 1999.

3.3.6 Mains cord


1 - 4 *60487 Mains cord Europe

1 20078 - Strain relief 1

2 21595 - Mains cord, 3 m 1

4 20079 - Nut for strain relief 1

1 - 5 *60486 Mains cord, USA 220V

1 20078 - strain relief 1

2 21495 - Mains cord, 3m 1

3 21596 - Power plug 220 VAC 1


5 69931 - Mains cord sticker 230V (110V) 1

1 - 5 *60496 Mains cord, Japan 100V

1 20078 - Strain relief 1

2 21495 - Mains cord, 5m 1

3 21472 - Power plug 1


3 Column unit



1 - 11 *60401 Column base plate, compl.

1 *602 83 Column base plate 1 See note 1

1 *605 06 Column base plate 1

2 2754 Screw M4x8 4

3 293 Screw M6 x 20 4

4 4657 Washer 1

5 329 Nut M10 1

6 *20520 Rubber bumper 1

7 *60259 Side plate 1

8 *60257 Strain relief mount 1 2

9 21443 Screw M4x8 4

10 3588 Washer 4

11 *603 62 Screw (in column) 2

12 335 Washer 2

13 2396 Washer 2

14 328 Nut M8 2

Note 1: From s/n 70396 the column base plate has been modified so that the spiral cords can be replacedwithout removing the base plate assembly. Strain relief mount is mounted onto the column inside instead ofcolumn base plate.

9

10

8

5

3

4

7

6

2

11 12

1

13

14


3 Column unit


1-11,15 60300 Wall mount assembly, complete 1

1-4,11,15 60517 Wall mount assembly USA, compl. 1

1 *60253 Wall bracket 1 See note 3

2 *6025 5 Column bracket 1

3 *2756 Bolt M12 x 30 2

4 337 Washer 13.0A 2

5 4762 Screw 8 x 75 2

6 335 Washer 8.4A 2

3242 Washer f 28mm 2 See note 4

7 3015 Plug S10 2

8 3011 Screw 6x45 3

9 334 Washer 6.4B 3

10 3014 Plug S8 3

11 337 Washer 2

12 335 Washer 2

13 2396 Washer 2

14 328 Nut 2

15 60544 Sticker (Torque) 1 See note 1

16 60362 Screw (in column) 2

3

603004

1

2

11 125

7

13 6

1416

15

3 Column unit



20 60564 Wall mount fixed 1 See note 2

Note 1: All models

Note 2: Optimal wall mount without swivel

Note 3: From s/n 73380 2 fixing holes are oblong

Note 4: This washer used in units manufactured from August 1998

3.4 Remote exposure button


69961 Remote exposure, complete 1

60183 Optional exposure button with indicator, complete 1

30029 Holder 1

21514 Screw 2

3.5 OP100 Base plate (old model)

56 3

1

2

4

4

EXPOSURE BUTTON30029

21514

WARNING LIGHT

20 M

CODE 60183


3 Column unit


1-7 60280 OP 100 base plate, complete

1 *6034 1 Base plate 1

2 *M60377 Trim plate 1

3 60399 Trim plug ∅ 10/17 6

4 20595 Allen screw M10 x 20 DIN 913 6 See note 1

4 60400 Leveling pad 6 See note 2

5 4324 Screw M8x20 5

6 335 Washer 8.4 5

7 *60356 Package, wooden crate 1

Note 1: Old model leveled with screws, up to 12/93.

Note 2: New model with leveling pads, from 01/94.

OP100 Base plate, from 12/95


60582 OP100 Base plate II, complete

60515 Base plate 1

60399 Trim plug∅ 10/17 6

60400 Leveling pad 6

4324 Screw M8 x 20 5

335 Washer 8.4 5

*60356 Package, wooden crate 1

60646 Base plate, exhibition 1

60515

4324

335

60399

60400

3 Column unit


3.6 OC100 Base plate (old model)


1-12 60440 OC100 base plate, complete

1 *6034 1 Base plate 1

2 *60337 Trim plate 1

3 60399 Trim plug∅ 10/17 6

4 20595 Allen screw M10 x 20 DIN 913 7 See note 1

4 60400 Leveling pad 7 See note 2

5 4324 Screw M8 x 20 5

6 335 Washer 8.4 5

7 60360 Support arm assembly 1

8 68177 - Support arm 1

9 = 4 - leveling pad 1

10 = 3 60399 - trim plug 1

11 = 6 335 - washer 2

12 302 - screw 2

13 *60356 Package, wooden crate 1

Note 1: Old model leveled with screws, up to 12/93.

Note 2: New model with leveling pads, from 01/94.

7

10

12 11

9

8

1

4

5 6

2

4

3


3 Column unit

OC100 Base plate, from 12/95


60583 OC100 base plate II, complete

60515 Base Plate 1

60399 Trim plug ∅ 10/17 6

60400 Leveling pad 6

4324 Screw M8 x 20 5

335 Washer 8.4 5

60360 Support arm assembly 1

68177 - support arm 1

60400 - leveling pad 1

60399 - trim plug 1

335 - washer 2

302 - screw 2

*60356 Package wooden crate 1

30260360 335

4324

60515

60400 60399

60400


3 Column unit


4 Rotating unit/ carriage assembly



1-81 61240 Rotating Unit /Carriage Assembly 1 See note 1

61255 Rotating Unit / Carriage Assembly Japan 1 See note 1

1-81 61258 Rotating Unit /Carriage Assembly MK2 1 See note 2

61150 Vertical Carriage, compl. 1 See note 1

1 *6 1235 Chassis Assembly 1 See note 1

61340 Chassis Assembly 1 See note 16

335 Washer 6 See note 1




3754 Screw 6 See note 1

1 61235 Chassis Assembly MK2 1 See note 2

2 *62870 Lower shelf Assembly 1 section 4.9

*2396 Washer 8.4A 4

*2676 Screw M8 4

3 ‘62000 Main Support Assembly 1 section 4.8

*2396 Washer 8.4A 4

*2676 Screw M8 4

9 61228 Control panel holder, compl. 1

61157 Control panel holder 1

259 Screw M4 x 2

325 Nut M4 2

21360 Plug 2

5722 Washer 2

20593 Magnet 4

10 Carriage left side 1 section 4.5

12 Carriage right side 1 section 4.6

13 61160 Control panel complete 1 section 4.7

14 63740 Rotating unit assembly 1 See note 3, section 5

14 63847 Rotating Unit Assembly MK2 1 See note 4, section 5

15 66417 Generator 1 See note 3, section 5

15 66437 Generator MK2 1 See note 4, section 5

16 67242 Collimator OP100 JT 1 See note 5, section 5

17 67243 Collimator OC100 JT 1 See note 6, section 5

17 67260 Collimator OC100 JT,cm 1 See note 7, section 5

17 67251 Collimator OC100 JT,inch Japan 1 See note 8, section 5

17 67270 Collimator OC100 JT,inch Japan 1 See note 9, section 5

17 67292 Collimator OC100 JT,inch USA 1 See note 10, section 5

20 21674 Screw M8 2 See note 11

21 328 Nut M8 2 See note 11

22 542 Washer 2 See note 11

30 66399 OP100 front cover 1

30 68214 OC100 front cover EUR. 18x24 AV/SV, 24x30AV 1

30 68213 OC100 front cover JAPAN8”x10” AV/SV, 10”x12” AV

1

30 68315 OC100 front cover USA/CAN8”x10” AV/SV, 10”x8”AH

1

31 66346 OP/OC 100 back cover 1

32 3069 Cover screw M4x12 6

30 64418 OC100 front cover EUR. 18x24 AV/SV, 18x24 AH 1




40 65475 Cassette rack assembly ''JS'' 1 Section 5

40 6550 Cassette rack assembly ''JT'' 1 Section 5

40 65600 Cassette rack assembly 1 Section 5

60 *6 1135 Carriage top plate 1 See note 14

*3588 Washer 4

*3230 Screw M4 4

65 *61126 Carriage upper trim cover 1

*3588 Washer 4.3 2

*2656 Screw M4 2

70 61220 Mirror cover, compl. 1

61343 Mirror cover, compl. - incl. 72 - 78 1 See note 16

70 61256 Mirror cover Japan,compl. - incl. 72 - 73, 77 -79

1

70 61261 Mirror cover OT 1 See note 13

61344 Mirror cover OT 1 See note 16

71 *5708 - Screw M4 2

72 61125 Carriage trim cover 1 See note 15

61337 Carriage trim cover 1 See note 16

73 *69936 - Sticker, Warning 1

74 *69940 - Sticker, Ch Sy Er Pr Sr (English) 1 See note 12

79 *6 1254 - Sticker, Ch Sy Er Pr Sr (Japanese) 1

77 61168 Mirror 1

80 *6 1127 Carriage lower trim cover 1

81 *5708 - Screw M4 2

Note 1 = units s/n 70000 - 70999

Note 2 = units s/n 71000 -->

Note 3 = Note 1

Note 4 = Note 2

Note 5 = units s/n, 70000 - 70271, 70272 - 70608, 70609 -->

Note 6 = units s/n 70000 - 70559

Note 7 = units s/n 70581 -->

Note 8 = units s/n 70000 - 70559

Note 9 = units s/n 70714 -->

Note 10 = units s/n 70458 -->

Note 11 = units s/n 71000 -->



Note 12 = units without sticker from s/n 71837

Note 13 = Ortho Trans units

Note 14 = From s/n 72273 with structure color painted.

Note 15 = From s/n 72000 the cover fixed with 4 screws.

Note 16 = From s/n 74238 the movement of the FH-projector extended downwards 36mm.

4.1 Chassis assembly


1-73 *61235 Chassis assembly, compl. 1 See note 1

1-73 *61259 Chassis assembly, compl. 1 See note 2

1 *61124 Chassis 1

1 61340 Chassis 1

2 *21290 Insulators 2

3 20185 Screw 6

4 68960 Cable C9 1

5 4589 Panduit 1

6 351 Panduit 1

7 Socket X 107 1 See note 7

8 *69946 Sticker X 107 1

9 Socket X 108 1 See note 7

10 *69947 Sticker X 108 1




11 *68953 Cable C 2 (T1-T2-X24-X25) 1

12 *69942 Sticker Fuse 1

13 68963 Cable C12 1 See note 10

14 68952 Cable C1 1

16 61155 FH projector, compl. 1

17 3556 Screw 3

18 3588 Washer 3

19 21187 Screw 4

20 *68977 Transformer T1, compl. 1

21 61200 Mid-sagittal light projector, compl. 1

22 2656 Screw 2

23 3588 Washer 2

30 *68976 Transformer T2, compl. 1

35 61134 Carriage bottom plate 1

35 61317 Carriage bottom plate 1 See note 9

36 3230 Screw 2

37 3588 Washer 2

40=41- 60160 Line filter, compl. 1

48

41 21297 - Line filter 1

41 69025 - Line filter 1 See note 9

42 68952 - Cable C1 (X101) 1

43 - Cable (red to fuse) 1 See note 8

44 - Cable (blue to fuse) 1 See note 8

45 - Ground wire (X 122) 1 See note 8

46 - Ground wire 1 See note 8

47 *2740 - Screw M4 x 2

48 *5722 - Washer 2

49 *3113 Sticker, Protective ground 2

50 *6 1167 Sliding piece 1 See notes 1, 3

51 *2395 - Washer 6.4 2 See notes 1, 3

52 *20574 - Screw M6 x 14 2 See notes 1, 3

55 *6 1159 CPU Static shield 1

60=62- 60112 CPU Board, compl. 1 See section 8, see note 4

64

62 60130 EPROM, User Programs 1 See note 5

63 60137 EPROM, Service Programs 1 See note 5

64 60129 EPROM, ICD25, PAL, address/timer circuit 1 See note 6

66 5 4 2 Washer 4.3 2

67 20184 Screw, Ms 8

68 20390 Screw, Pa 4




70 69934 Warning sticker 1

71 21975 RF-Choke 2 See note 9

Note 1: Units s/n 70000 - 70999.

Note 2: From unit s/n 71000.

Note 3: Located behind the chassis.

Note 4: For Toshiba D-05 1S X-ray tube type please specify the correct software version: 1.2.01 or higher.

Note 5: Please specify the correct software version and X-ray tube type. Both User and Service programsMUST have the same version number!

Note 6: Use only a chip which has been initialized at factory.

Note 7: Part belongs to Cable C2, code 68953.


Note 9: Units with CE-marking, from s/n 72000.

Note 10: The place changed in units with CE-marking, from s/n 72000.


1-50 61155 FH Projector, compl. See note 1

1 61226 Light projector assembly 1

8 61156 Axle 1

9 68122 Knob 1

4.2 FH projector assembly

1

38

12

41 44

45

43

11

31

23

9

8

15

22

25

20

24

1

2250

60




11 61184 Mirror assembly 1

12 61185 Light shield 1 See note 1

15 21293 Spring 1

20 4292 Washer 2

22 3588 Washer 4

23 365 Allen screw 1

24 9792 Screw 2

25 2656 Screw 1

31 61162 Lens assembly 1

38 20912 Lamp 12 V / 20 W 1

41 6699 Screw 2


44 4292 Washer 2


50 3556 Screw 3

60 61153 Guide 2

61338 Guide 2 See note 1

Note: The FH projector can be installed to the left or right side of the vertical carriage. Please refer toInstallation Manual for details. From unit s/n 76672 up/down adjustment added filament place of the lampchanged. Lamp holder screw longer.

Note 1: From s/n 74238 the movement of the FH-projector extended downwards 36mm.

4.3 Mid-sagittal projector assembly


1-9 *61200 Mid-sagittal projector, compl.




1 61226 Light projector 1

2 20912 Lamp 12 V / 20 W 1

3 20712 Allen screw M4 x 4 1

4 61188 Projector mounting piece 1 See note 1

4 61242 Projector mounting piece 1 See note 2

5 61187 Mounting plate 1 See note 1

5 61243 Mounting plate 1 See note 2

6 542 Washer 2

7 3230 Screw 2

8 3588 Washer 2

9 2656 Screw 2

Note 1: Unit s/n 70000-70462.


4.4 Bottom plate assembly


1-23 61280 Bottom plate assembly, compl.

61301 Bottom plate assembly CE, compl. See note 5

1 *6 1134 Carriage bottom plate 1

1 *61317 Carriage bottom plate CE 1 See note 5

2 *69930 Sticker, Main label, Russia 1 See note 1

60536 Sticker, Main label, USA, Japan, Canada

61251 Sticker, Main label, Germany

*613 15 Sticker CE 1 See note 5

19




3 *3230 Screw 2

4 *3588 Washer 2

5 20367 Power switch 1

6 69028 -Cable to fuse (red) C 1/2 1 See note 4

7 69030 - Cable to fuse (blue) C 1/4 1 See note 4

8 68952 - Cable C1 to CPU (X21) 1

10 21174 - Fuse holder 2

11 21175 - Fuse holder cap 2

12 20154 Fuse 10 AT 2 See note 3

12 20045 Fuse 15 AT 2 See note 3

13 *69942 Sticker, Fuses 1

14 *61213 Sticker F1/F2 L/N 1

15 68960 Cable C 9 (Control panel) 1

16 *20267 Screws to D connector 2

17 68963 Cable C 12 (RS-232 to CPU) 1 See note 6

18 20267 Screws to D connector 2

19 69031 Cable C 1/5 1

22 61179 Transportation plate 1 See note 2

23 9590 Screw M4 x 16 2

Note 1: Main label can be requested only if the old one is no longer readable. Serial number must be includedwith order.

Note 2: Removed after installation.

Note 3: Check the line voltage setting to obtain correct fuses.


Note 5: Units with CE-marking, from s/n 72000. Bottom plate from s/n 72273 painted with structure color.

Note 6: The place changed in units with CE-marking, from s/n 72000.



4.5 Carriage left side


*61229 Carriage left side lower door, compl. 1

*61231 Carriage left side upper door, compl. 1

20-33 *6 1233 Warning light left, compl. 1 See note 5

1 *6 1129 Side box chassis L 1 See note 6

2 *6 1186 Sliding guide 1 See note 1

3 *3230 Screw M4 x 10 2 See note 1

4 *3589 Stop screw M6 x 10 1 See note 1

5 *61176 Cover 1

6 *4292 Washer 2

7 *3257 Screw M3 2

9 61231 Side box cover L upper door, compl. 1

10 *61121 Side box cover L 1

11 68964 Cable C 13 (X 110 for ceph) 1

12 68958 Cable C 7 (Holder for Warning lamp) 1

13 *202 10 Cable anchor (for X 110) 1

14 *4165 Cable tie 1

15 69937 Sticker, Check errors 1

1 6




15 61253 Sticker, Check errors, Japanese 1

16 61150 Plastic plug 1

20 *6 1146 Warning light chassis, left 1 See note 2

20 *6 1223 Warning light chassis, left 1 See note 3

21 *6156 Lamp holder 1

22 *61236 Insulator 1

23 *2742 Screw M4x16 1

24 6027 Lamp 12 V / 5 W 1

25 61190 Holding piece 1 See note 2

26 *4291 Washer 1

27 *3556 Screw M4 x 14 1

30 *61131 Reflector 1

31 *61237 Color tape

32 *4172 Magnet 1

33 *63782 Holder for TMJ pointer 1 See note 2


35 61244 Warning light chassis 1 See note 4

40 *61123 Side box lid L 1

41 61227 Magnet band 1

42 *61130 Door knob 1

43 2733 Screw 2

4292 Washer 2

44 *61140 Bin 6 See note 8

45 *61189 Bin hinge rod 1

61265 Bin hinge rod 1 See note 4

46 61316 Cover (for Digipan cable) 1 See note 7

6699 Screw 2

331 Washer 2

4274 Nut 2

47 61176 Cover (for Cephalostat cable) 1

3257 Screw 2

4292 Washer 2

Note 1: Needed only during “one man” installation, not equipped with all models. Unit s/n 70000-70560.Digital readiness from s/n 76070.

Note 2: All models up to s/n 70240 and 70243 to 70245 with TMJ pointer (code 69962).

Note 3: All models s/n 70241, 70242 and from 70246 with TMJ pointer, model A (code 60477).

Note 4: From unit s/n 71205

Note 5: Units 70000-71204



Note 6: The place of the serial port 1 (connected X1 06 for Ortho ID, cable C1 2 has been moved to the left sidebox. From s/n 76070 opening for digital contact added. From s/n 78568 hole added.

Note 7: Units with CE-marking, from s/n 72000.

Note 8: From unit s/n 73448 there are 5 Bins (more space for the accessories). Two bushings, code 72027,replace one bin.

4.6 Carriage right side


*61230 Carriage right side lower door, compl. 1

‘61232 Carriage right side upper door, compl. 1

40-53 *6 1234 Warning light right, compl. 1 See note 5

1 *61132 Side box chassis R 1

2 *6 1186 Sliding guide 1 See note 1

3 *3230 Screw M4 x 10 2 See note 1

4 *3589 Stop screw M6 x 10 1 See note 1

5 *61176 Cover (ceph cable opening) 1

6 *4292 Washer 2

7 *3257 Screw M3 2

10 *61178 Insulator for capacitor 1

11 *61141 Capacitor mount 1

12 *2743 Screw 2




13 *324 Nut M4 2

14 *21299 Capacitor 1500uF / 250 V 2

20 *61183 Insulator for Power Supply Board 1

21 20185 Pillar screw 4

22 60113 Power Supply Board, compl. 1


24 21274 Fuse 6.3AT 2

25 21275 Fuse 2 AT 1

26 61232 Side box cover R upper door, compl. 1

30 *61121 Side box cover R 1

31 *303 64 Sticker, High Voltage 1

32 *69932 Sticker, Caution 230/110 Supply 1

32 *60533 Sticker, Caution 230/110 Supply (Eng/F) 1 USA/Canada models

33 *68964 Cable C 13 (X 121 for ceph) 1

34 *68958 Cable C 7 (Holder for Warning light) 1

34 69006 Cable C7 1 See note 3

35 *4589 Cable anchor 1

36 *351 Cable tie 1

40 *6 1147 Warning light chassis, right 1 See note 2

40 *6 1224 Warning light chassis, right 1 See note 3

41 *6156 Lamp holder 1

42 *61236 Insulator 1

43 *2742 Screw M4x16 1

44 6027 Lamp 12 V / 5 W 1

45 *6 1190 Holding piece 1 See note 2

46 *4291 Washer 1

47 *3556 Screw M4 x 14 1

50 *61131 Reflector 1

51 *61237 Color tape 1

52 *4172 Magnet 1 See note 2



55 61244 Warning light chassis 1 See note 4

60 *61122 Side box lid R 1

61 *21227 Magnetic band 1

62 *61130 Door knob 1

63 2733 Screw 2

4292 Washer 2

64 *61140 Bin 3

65 *61189 Bin hinge rod 1

*6 1265 Bin hinge rod 1 See note 4




70 68955 Cable C 4 (for capacitors) 1

80 68956 Cable C 6 (supply voltages) 1

Note 1: Needed only during “one man” installation, not equipped with all models. Unit s/n 70000-70560.

Note 2: All models up to s/n 70240 and 70243 to 70245 with TMJ pointer (code 69962).

Note 3: All models with s/n 70241, 70242 and from 70246 with TMJ pointer, model A (code 60477).


Note 5: Unit s/n 70000-71204.

4.7 Control panel assembly


1-13 61160 Control Panel, compl. 1

1 61139 Frame 1

2 *61142 Bottom frame 1

61326 Micro switch holder 1 See note 2

21564 Screw 2 See note 2

331 Washer 3.2A 2 See note 2

5 61174 Magnet plate 1 See note 1

5 61246 Magnet plate 1 See note 1

6 69109 Control panel top 1

7 Control panel pcb assembly(60107) 1 See note 3

8 *68973 Cable SC 3 1

11 *21522 Cable clamp 1

13 *21292 Screw 6

7

6

1

2

8

5

13

11



Note 1: From July 1994 Magnet plate has a center pin for improved mounting.

Note 2: From unit s/n 72981 exposure Micro switch code 21077 are not interchangeable.

Note 3: From version 1.3 pcb assembly changed, see note 2. Old and new assemblies are not interchangeable.If the part no. 7 ordered the Control Panel complete 61160 will be delivered. From board V1 .4 s/n 10325capacitors C2 1 and C22 type changed. From s/n 79521 WARNING-text updated.

4 .8 M ai n su p po rt


62000 Main Support Assembly 1 See note 8

Units s/n 70000 - 709997

1

82

4

3 15 12

13

514

10

616

11

Units from s/n 71000 -7

18

2

3 154

1213

5 14

106

16 11




62010 Main Support Assembly MK2 1 See note 9

1 62003 Main support cover 1 See note 1

1 62051 Main support cover 1 See note 2

2 62060 Rotation switch assembly 1 Section 4.8.2

3 62024 IEC cover 1 Section 4.9

4 62067 Linear movement motor assembly 1 Section 4.8.4 and 5

62096 Linear movement motor assembly 1 See note 8

5 62065 Sliding chassis assembly 1 Section 4.8.1

6 62066 Head support holder 1 Section 4.9

7 5708 Screw 2

8 62061 Sliding plate complete 1 Section 4.8.3

10 2676 Screw 4

11 2396 Washer 4

12 60123 Interface board 1

60166 Interface board 1 See note 10

13 62031 Insulator, Interface Board 1


15 21390 Screw 4

16 *61991 Main support cast 1 See note 3

*61991 Main support cast 1 See note 4

*61991 Main support cast (Trophy) 1 See note 5

*61991 Main support cast (Trophy) 1 See note 6

62080 Main support cast MK2 1 See note 7

Note 1: This screw must be used during transportation including repacking. This screw secures the unit to themain support and it is removed after the installation.

Cover secured with 2 pcs screws. All models up to s/n 70224. Cover old model unit’s s/n 70000-70224.

Note 2: Cover secured with 2 pcs screws and plate lugs. All models from s/n 70225. Cover new model fromunit s/n 70225.

Note 3: Standard, no printing. All models except Trophy up to s/n 70224. Units s/n 70000-70999.

Note 4: Standard, no printing. All models except Trophy from s/n 70225. Units s/n 70000-70999.

Note 5: Trophy model with logo printed, up to s/n 70222. Units s/n 70000-70999.

Note 6: Trophy model with logo printed, from s/n 70225. Units s/n 70000-70999.

Note 7: From unit s/n 71000-

Note 8: Units s/n 70000-70999.

Note 9: From unit s/n 71000-

Note 10: Unit with OT-system or from s/n 71000. See section 8 electrical spare parts.



4.8.1 Sliding chassis assembly


*60265 Linear chassis assembly, compl. See note 1, 2

1 21481 Screw M2 x 12 6

2 21482 Washer 2.3 6

3 20014 Washer 2.3 3

4 *7229 Sticker, mm scale 1

5 *620 12 Bracket 1 See note 1, 2

6 *62033 Mounting plate 3

8 6220 Screw M6x30 4 See note 1


9 2395 Washer 6,4 4 See note 2

10 62007 Sliding chassis 1 See note 3

11 62027 Bushing 4

55 68962 Cable C11 1

Note 1: All models up to s/n 70260 screw 6220 used with bracket 62012.

Note 2: All models from s/n 70261 screw 954 and washer 2395 used with bracket 62012.

Note 3: Material type changed from s/n 72912.

Units s/n 70000-7099955

11



4.8.2 Rotation switch assembly


1-5 62060 Rotation switch assembly, compl.

1 *6200 1 Micro switch mount 1

2 21477 Screw M2 x 30 2

3 21482 Washer 2.3 2

4 20014 Micro switch 4

5 62033 Mounting plate 3

6 68962 Cable C11 (Micro switches) 1

7 2754 Screw M4 x 8 2

8 5722 Washer 4.3 2

9 62024 IEC-cover 1

9

2 3 5

6

4

7 8

1



4.8.3 Sliding plate assembly


*6206 1 Sliding plate, compl.

1 *62011 Sliding plate 1

2 62046 Slide rod 1

3 295 Screw M6 x 16 4

4 2395 Washer 6.4 4

5 295 Screw M6 4

6 2395 Washer 6.4 4


10 62004 Coupling bushing 3

11 62009 Slide rod 1

12 3689 Screw M6x25 3

13 2395 Washer 3

14 302 Locking screw M8x35 1 See note 1

Note 1: Part used to secure rotating unit to linear plate. Removed after installation.

Units from s/n 71000

7

3 4

5

6

2

1



4.8.4 Linear transmission assembly


70-75 62062 Kerk chassis assembly

70 *21221 Kerk nut 1

71 *61993 Mount for Kerk nut 1

72 *4266 Screw M6 x 16 2

3075 Screw M6x16

73 3556 Screw M4x14 Din 912 3

73 542 Washer 4.3 3

75 *2395 Washer 6.4 2

9-15 62096 Center chassis assembly See note 1

9-15 62063 Center chassis assembly See note 2

9 *4665 Circlip 20 x 1 1

10 *2023 1 Bearing 1

11 *6 1994 Bearing bushing 1 See note 1

11 62052 Bearing bushing 1 See note 2

12 *6202 Screw M4 x 25 1

13 *542 Washer 4.3A 1

14 4266 Screw M6 x 16 2 2001 changed

15 *2395 Washer 6.4 2

16 63775 Clutch (to s/n 70176) 1

62022 Fly wheel (to s/n 70176) 1

16=18-22

62059 Clutch assembly (from s/n 70177) 1

18 *62035 Fly wheel, screw side 1

19 *62036 Fly wheel, motor side 1

20 *21516 Rubber nut M4 x 8 x 12 3

21 *207 12 Allen screw M4 x 4 2

22 *3556 Screw M4 x 14 3

23 31024 Spacer 1

73

70

72

71

75

24

9 10

11

12 13

23

18

16

14 15

20

19

22




24 61995 Kerk screw 1

Note 1: Units s/n 70000- 70999

Note 2: From unit’s s/n 71000

4.8.5 Linear motor assembly


1-11 *62064 Linear motor, compl. 1

1=9 *326 Nut M5 8

2 *333 Washer 5.3 8

3 *6 1992 Motor chassis 1 See notes 1, 3

3 *62049 Motor chassis 1 See notes 2, 3

4=8 *541 Washer 5.3 4

5 * 1108 Attenuator screw 4

6 20319 Rubber damper 4 See note 1

7 68984 Stepper motor20907, linear movement 1

10 *2395 Washer 6.4 2

11 *294 Screw M6 x 10 2

Note 1: Units s/n 7000-70999.

Note 2: Units from s/n 710000-

Note 3: Pos.3. Parts 61992 and 62049 are interchangeable.

1 2

5

11

10

3 8

9

7

1 2 3

8

11

1 0 7

58

9






11 *2396 Washer 1

12 *3754 Locking screw M8x30 2 See note 2

13 *2396 Washer 8.4 6

Note 1: Transportation screw units from s/n 71000-

Note 2: These screws are used during transportation for securing the rotation unit and during operation aslimiters.

Note 3: Transportation screws units’s/n 70000-70999.

4.9 Head support holder, IEC cover, cable holders

10 11

12 13

7

Units s/n

70000 - 70240

1

2

6

7

8

UNITS s/n70000 - 70999

3

1216

4

13

9

5 10

11




1 4260 Screw M4x12 1

2 65 Cable tie w/anchor 1

3 542 Washer 1

4 62024 IEC cover 1

5 62025 Holder 1 See note 1

62066 Head support holder

6 295 Screw M6 x 16 4

7 540 Washer 6.3 4

8 62023 Head support holder 1

9 63766 Cable tie 2

10 3588 Washer 2

11 3069 Screw M4 2

12 6091 Screw M6 x 16 2

13 62021 Mounting piece 1

12 68964 Cable C13 1

14 2395 Washer 4

15 63766 Cable clamp 2

Units s/n 70241 - 70529201

21 4

1 9

From unit s/n 71000 -

3

12 15

16 18

17

4

30

31

Units s/n 70530-7229020

2214 19

23

12

21 18

30 25

31 24




16 3069 Screw 4

17 3588 Washer 4

18 68956 Cable C5 1

19 62032 Support 1

20 1820 Screw 4


22 3646 Screw 2

23 542 Washer 2

24 21483 Screw 2

25 331 Washer 2

30 64653 Plate 1

31 3202 Screw 2

Note 1: Units s/n 70000- 70999.



Head support holder, OT (all units 72291-73096)


62084 Support complete + cable C1 3 1

1 62081 Support OT 1

2 62082 Additional support 1


4 64653 Plate 1

5 68964 Cable C13 1

6 69020 OT kit, linear movement micro switch cable 1

7 3046 Screw M4x16 2

8 20477 Screw M4x30 2

9 2656 Screw M4x8 4

10 3202 Screw M3x6 2

Note: From s/n 72181 to USA and Canada and units with ORTHO TRANS system. From s/n 72291 all units.



head support holder, OT, all units from s/n 73097


62094 Support complete + cable C1 3 1

1 62088 Support OT 1

2 64701 Support plate 1

3 62091 Cover Plate 1


5 68964 Cable C13 1

6 69020 OT kit, linear movement micro switch cable 1

7 62089 Fixing plate, short 1

8 62090 Fixing plate, long 1

9 293 Screw M6x20 4

10 21483 Screw M3x10 2

11 3229 Screw M3x10 4

12 2395 Washer 4


14 4292 Washer 2



4.10 Lower shelf assembly


1-3, 8-21

62870 Lower shelf

1 62910 Shelf cast assembly 1 See note 1

62995 Shelf cast assembly 1 See note 4

2 62890 Layer Projector assembly 1 See note 2

*3588 Washer 1

*3230 Screw 1

3 62911 Layer Mirror assembly 1

4 62895 Sinus rest 1

4 68759 Sinus rest From s/n 79812

5 62875 Chin rest 1

5 68758 Chin rest 1 From s/n 79812

6 62958 Bite fork rod 80 mm 1

62988 Bite fork rod 71 mm 1 2648 old code

62985 Bite fork rod 56 mm 1 4401 old code

7 8878 Bite fork, 10 pcs 1 s/n 70000- 70682

62942 Bite fork OP 100, 10 pcs 1

8 60108 Patient positioning panel assembly 1

9 4292 Washer 3.2 2

10 4711 Nut M3 2

11 3588 Washer 2

12 3230 Screw 2

13 62892 Locking piece 1

14 21393 Spring 2




15 331 Washer 2

16 21187 Screw 2

17 68957 Cable C6 1

18 68961 Cable C10 1

*2 1453 Flat cable holder 1

*4262 Screw M4x10 1

19 62877 Side trim cover 1

4292 Washer 3.2 2

4711 Nut M3 2

20 62873 Bottom trim cover 1 See note 5

21 3202 Screw M3x6 6

21509 Screw M3x6 6 See note 3

21443 Screw M4x8 6 Note 6

*68969 Cable, grounding 1

*20210 Cable tie anchor 1

*2740 Screw M4x6 1

*45 89 Cable tie anchor 1

Note 1: Older models with green handles, newer ones with white. New shelf with intergraded handles, unitswith s/n 70511-70519, 70527-70539 and 70544 and up.

Note 2: All OP 100 models up to 70462 and 70472: Projector orientation change between left and right bydisassembling the projector. Spare parts and all OP 100 models from 70463 to 70471 and from 70473:Universal projector fitted for left and right orientation. Filament place of the lamp changed from s/n 76672.From s/n 79393 opening for patient positioning panel bigger.

Note 3: From unit s/n 71000 and up to s/n 77262.

Note 4: From unit s/n 73102 and up. Shelf angle adjustment added for chin rest correct height. Adjustingscrews code 295, M6x16, 2ea.

Note 5: From unit s/n 77263 screw holes changed from 4,5 mm to 5 mm.


5 Rotating unit


5 Rotating unit


1 63740 Rotating unit cast, Model "JS" (Std Slit) 1 See note 1, section 5.1

1 63800 Rotating unit cast, Model "JT" (Narrow Slit) 1 See note 2, section 5.1

1 63847 Rotating unit cast, Model MK2 1 See note 3, section 5.1

2 64605 Head support assembly 1 section5 .2

3 66417 Generator assembly 1 Section 5.3

3 66437 Generator assembly MK2 1 See note 3, 5.3

4 65475 Cassette rack assembly "JS" 1 Section 5.4

4 65500 Cassette rack assembly "JT" 1 Section 5.4

4 65600 Cassette rack assembly 1 Section 5.4

4 65705 Cassette rack assembly MK2 1 See note 3, 5.4

4 65788 Cassette rack for Digipan system 1 Section 5.4

5 65701 Cassette rack CR 1 Section 5.4.3

5 65706 Cassette rack CR MK2 1 See note 4, section 5.4.3

Note 1: There are two models; "JS" for standard primary slit and "JT" for narrow slit. The letters are stampedon the slit located in the collimator assembly. Standard in all models from serial number 70000 to 70146.Some units may have been modified at field for "JT" slit.

Note 2: "JT" stamped for narrow slit. Standard in all models from serial number 70147, also earlier modelshave been modified at field for "JS" slit.


Note 4: All OP/OC 100 CR models.

5 Rotating unit


5.1 Rotating unit cast, units s/n 70000-70999


63470 Rotating unit cast, Model "JS" (Std Slit) See note 1

63800 Rotating unit cast, Model "JT" (Narrow Slit) See note 2

1 63822 Rotating motor assembly 1

2 63745 Cover plate 1

5 5708 Screw 2

10 63786 Rotating disk 1

13 63790 Support 2

16 63734 Code disk 1

17 3202 Screw 2

20 63757 Cover 1

36 3754 Screw 2

39 63789 Lock plate 2

40 6221 Screw 4

41 2754 Screw 4

42 63750 Gear with motor 1

63958 Rotating drive kit 1

36

16

10

13

41

39

17

5

2

20

40

42

1


5 Rotating unit

5.1.1 Rotating unit drive motor assembly, units s/n 70000-70999


63822 rotating motor assembly 1

2 3075 screw 1

3 21236 Spring 1

4 335 Washer 1

5 3045 Nut 3

6 2395 Washer 1

7 295 Screw 1

8 63797 Axle 1

9 20504 Spacer washer 4

10 335 Washer 1

11 5477 Nut 1

42 63750 Gear with motor 1

5 Rotating unit


5.1.2 Rotating unit cast, from unit s/n 71000-


63847 Rotating unit assembly

1 63823 Gear with motor assembly 1


3 20504 Spacer washer 4

4 60344 Screw 1

5 5708 Screw 2

6 63792 Housing 1


8 20570 Screw 2

9 21672 Screw 1

10 63811 Rotating disk 1

63791 Pin 1

63814 Plate 1

4262 Screw 2

11 5477 Nut M8 1

12 3045 Nut M8 2

13 63790 Support 2

14 335 Washer 1

15 21236 Spring 1

16 63734 Code disk 1

17 3202 Screw 2

19 63841 Rotating unit cast 1

43


5 Rotating unit


20 63757 Cover 1

63819 Cover OT 1 Note 1

21 3230 Screw 1

22 6617 Screw 1

23 63773 Angle plate 1

24 22568 Bearing 2

39 63816 Lock plate 2

40 6221 screw 4

41 21443 Screw 4

42 63753 Fixing ring 1 Note 2

22341 Washer 6 Note 2

4262 Screw 6 Note 2

43 30078 Flange with nut 1

Note 1: Units with Ortho Trans system

Note 2: From unit s/n 72857 and up. 6 washers and screws replace the fixing ring.

5 Rotating unit


5.2 Head support, units s/n 70000-70240


1+2 *64605 Head support assembly

11 4422 Screw 4


41 20023 Screw 2

50 20341 Spring 2

51 64629 Magnet spring axle 1

52 64631 Spring chassis 1

146 64602 Bushing 2

147 64624 Linear shaft 2 1

64618 Linear shaft 1 1

21382 O-ring 4


151


5 Rotating unit





165 6321 Forehead support plate 1

243 64622 Magnet body 1

244 60134 Head support lock 1

245 64623 Magnet spring plate 1

245 64648 Magnet spring plate 1

245 a 64653 Plate for magnet 1

246 64625 Sliding bushing 1

5.3 Head support, units s/n 70241- 71360

5 Rotating unit



1 64658 Head support linear movement 1

2 64657 Head positioner bracket 1

3 64653 plate 1

4 20959 Bearing 4

5 3202 Screw 2

6 64649 Guide 2

7 3588 Washer 4

8 3230 Screw 4

9 60134 Coil with board 1

11 4422 Screw 4

12 6322 plating plug 2

13 6321 Forehead support 1

14 60136 Head support lock switches 1

41 21443 Screw 2

42 64634 Head guard 1

43 64647 Sliding chassis 1 See note 1

64660 Sliding chassis 1 See note 2

Note 1: Units s/n 70241-70350.

Note 2: Form unit s/n 70351.


5 Rotating unit

5.4 Head support, units 71308, 71358 and from unit s/n 71361


1 64658 Head support linear movement 1

2 64657 Head positioner bracket 1

3 64653 Plate 1

4 20959 Bearing 3

5 3202 Screw 2

6 64649 Guide 2

7 3588 Washer 4

8 2656 Screw 4

9 60134 Coil with board 1

11 4422 Screw 4




41 20023 Plastic screw 2

42 64634 Head guard 1

5 Rotating unit



64692 Head guard 1 Note 1

43 64660 Sliding chassis 1

Note 1: From unit s/n 72181 and up to USA and Canada and all units from s/n 72291 and up and all OT units.

Head support with ortho trans system


64669 Head support assembly 1 See note 1

1 64670 Bracket 1

2 64671 Cover 2

3 64641 Isolator plate 2

4 64677 Pin 1

5 21805 Screw 1

6 64676 Knob 1

7 64674 Pin with head 1

9 2071 Screw 2

10 64675 Pin 1




30 21496 Screw M5x16 2

32 4422 Screw M4x12 4

34 21509 Screw M3x6 2

4

10

8

5

7

9

6


5 Rotating unit


35 21422 Screw M3x5 2

50 64696 Head support 1

51 64695 Support 1

Note 1: From s/n 72181 units shipped to USA and Canada.

5.4.1 Hair cover, units s/n 70000-70240


1 63758 Hair cover 1

2 63787 Spring plate 2

3 2746 Screw M3x8 2

4 63782 Holder for TMJ pointer 2

5 5708 Screw M4x8 4

6 4172 Magnet 2

26

25

6

5 Rotating unit


5.4.2 Hair cover, from unit s/n 70241


1-5 63745 Hair cover, complete 1

1-5 63853 Hair cover OT, complete 1 Note 1


1 63793 Hair cover 1

63852 Hair cover OT 1 Note 1

2 64650 Holder mount 2

3 21564 Screw 2.5x6 2

4 64643 Holder for TMJ pointer 2

5 5708 Screw M4x8 2

Note 1: For Ortho Trans units and all units from s/n 71831.

5.5 Generator assembly

5.5.1 Tube head assembly, Inverter & Filament Boards


66417 Generator OP 100 type 1, (Toshiba) , units s/n70000 - 70999

66437 Generator OP 100 type 1, MK2 (Toshiba), from units/n 71000

2

4 5

3 1


5 Rotating unit


1 6386 Adjusting screw 1

2 66371 Tube head support, left 1

3 66369 Tube head support, right 1


5 60114 Filament Control Board 1

6 3069 Screw 4

7 66360 Tube Head, Toshiba 1 Note 2

8 68967 Cable C16 1

9 68966 Cable C15 1

10 68965 Cable C14 1

11 335 Washer 4

12 2395 Washer 4

13 297 Screw 4

14 4291 Washer 4

15 3069 Screw 4

16 60115 Inverter board 1

20154 Fuse 10 AT 1 Note 1

17 66397 Isolation plate 1

18 3588 Washer 4

19 4262 Screw 4

20 2740 Screw 8

21 5722 Washer 8

22 3926 Screw 4

23 21095 Spacer 4

24 4291 Washer 4

25 66374 Mounting plate, Inverter Board 1

26 66376 Mounting plate, Filament Control Board 1

27 66446 Cover holder 2 Note 3

28 2656 screw M4x8 4

29 3588 Washer 4,3 4

66451 X-ray window 1 Note 4

Note 1: Inverter board version 1.3, fuse 1 6AFF Inverter board version 1.4, fuse 10 AT, from unit s/n 71149. 16AFF fuse may be replaced with 10 AT also in earlier versions.

27

28

24

29

5 Rotating unit


Note 2: Tube head from version 1.4 the Cable C16 is included. From s/n 74893 version 1.5 changes on

Cascade Board. Version 1.6 changes on Cascade Board from tube head s/n 8607. From s/n 8773 insulatingmaterial changed. From s/n 79564 labeling changed, focus size symbol added. From s/n 79772 unit type labelchanged. From s/n 79763 unit type label changed.

Note 3: Cover holder changed January 1997.

Note 4: Screw changed to lock pin from s/n 6543.

5.5.2 Collimator assembly

5.5.2.1 Collimator OP100, unit’s s/n 70000-70271


67215 Collimator OP 100, complete,JS, Units s/n 70000 -70271

67242 Collimator OP 100, complete,JT, Units s/n 70000 -70271

1 4422 Screw 2

2 6277 Pin 2

3 7410 Primary slit plate JS 1

4 6698 Spring 1

5 1704 Spring 1


Units s/n 70000 - 702711 3

2 6

416

5 6

118

7 14

9 15

12

10

13


5 Rotating unit

7 67236 QA filter knob 1

8 365 Screw 1

9 67238 rod 1

10 21490 Screw 1


12 62033 Nut plate 1

13 68968 Cable C17 1

14 20041 Screw 4


15 4291 Washer 4

16 7409 Primary slit plate slide 1

5.5.2.2 Collimator OP100, unit’s s/n 70272-70608


67242 Collimator OP 100 JT

1 2754 Screw 2

2 6277 Pin 2

3 67312 Primary slot plate 1

4 6698 Spring 1

5 1704 Spring 1

5 Rotating unit



7 67236 Knob 1

8 365 Screw 1

9 67238 Rod 1

10 21490 Screw 2


12§ 62033 Nut plate 1

13 68968 Cable C17 1

14 20477 Screw M4x30 4

15 3588 Washer 4

16 9792 Screw 1

17 67247 Flange 1

18 7409 Primary slot plate slide 1


5 Rotating unit

5.5.2.3 Collimator OP100, units from s/n 70609


67242 Collimator OP 100 JT

1 2754 Screw 2

2 6277 Pin 2

3 67312 Primary slot plate 1 From s/n 79968 withoutblack paint

4 6698 Spring 1

5 1704 Spring 1


7 67236 Knob 1

8 365 Screw 1

9 67238 Rod 1

10 21490 Screw 2


12 62033 Nut plate 1

13 68968 Cable C17 1

14 20477 Screw M4x30 4

15 3588 Washer 4

16 9792 Screw 1

17 67293 Flange 1

18 7409 Primary slot slide 1

5 Rotating unit


5.5.2.4 Collimator OC100 M, JT, unit’s s/n 70000-70559


67243 Collimator OC100 M, JT, s/n 70000-70559

1 62033 Nut plate 1

2 67212 Slot plate guide 1


6 67216 Aperture plate, OC (18x24, 24x30)cm 1 Note 1

10 67241 Soft tissue wedge 1

15 68173 Wheel 1

18 68121 Rod 2

21 68264 Primary slot plate QA, JT 1

22 68979 Cable CC1 1


24 6515 Gross roller bearing 2

25 20605 Ball screw 1


27 21279 Spring 1

28 21477 Screw 2


30 68122 Knob 2

33 21483 Screw 4


39 6277 Pin 2

40 6698 Spring 1

41 6091 Screw 1

42 4274 Nut 4

42

33

47

30

29

18

27

6

53

1

23

43

10

21 39

28

40

1 22

41

2

52

46

24

38

25

45

3

45

26 29

15

18

30


5 Rotating unit


43 4292 Washer 2

45 2737 Screw 1

46 7120 Screw 2

47 2734 Screw 1

52 20041 Screw 4

53 4291 Washer 4

Note 1: Ceph images sizes 1 8x24cmSV, 1 8x24cmAV and 24x30cmAV.

5.5.2.5 OC100 Inch, JT, Japan Collimator, unit’s s/n 70000-70559


67251 Collimator OC100 Inch, JT, Japan s/n 70000-70559

1 62033 Nut plate 1

2 67212 Slot plate guide 1


6 67189 Aperture plate, OC (8x10, 10x12)inch 1 Note 1


15 68173 Wheel 1

18 68121 Rod 2

21 68264 Primary slot plate QA, JT 1

22 68979 Cable CC1 1


24 6515 Gross roller bearing 2



27 21279 Spring 1

42

33

47

30

29

18

27

6

53

1

23

43

10

21 39

28

40

1 22

41

2

52

46

24

38

25

45

3

45

26 29

15

18

30

5 Rotating unit



28 21477 Screw 2


30 68122 Knob 2

33 21483 Screw 4


39 6277 Pin 2

40 6698 Spring 1

41 6091 Screw 1

42 4274 Nut 4

43 4292 Washer 2

45 2737 Screw 1

46 7120 Screw 2

47 2734 Screw 1

52 20041 Screw 4

53 4291 Washer 4

Note 1: Ceph image sizes 8x10inAV and 10x12in AV.


5 Rotating unit

5.5.2.6 OC100, M, JT, collimator, from unit s/n 70581


67260 Collimator OC100, M, JT (18x24, 24x30)cm, fromunit s/n 70581

67369 18x24 SV, AV, AH From unit s/n 79311

1 67288 Sliding plate assembly 1

2 67289 Collimator frame 1

3 67290 Soft tissue wedge assembly 1

5 68979 Cable CC1 1

6 67258 Aperture plate, left 1 8x24cm SV/AV and 24x30cmAV

1 Note 1

7 67259 Aperture plate, right 1 8x24cm SV/AV and 24x30cmAV

1 Note 1

62

5 Rotating unit



64416 Aperture plate, 1 8x24s/1 8x24 AH Right 1

64417 Aperture plate, 1 8x24 S/A/AH Left 1

8 67312 Primary slot plate, OP 100 JT 1 Note 5

9 68135 Primary slot plate, OP 100 QA, JT 1

16 67261 Rod 1

21 68122 Knob 2

26 67293 Collimator flange 1 Note 3


34 67271 Soft tissue wedge 1 Note 4

67358 Soft tissue wedge 1 Note 4

36 67284 Rod 1

39 6277 Pin 3


42 6698 Spring 1

43 21279 Spring 1

44 21477 Screw 2


47 6699 Screw 7

48 2757 screw 2

51 2656 Screw 4

53 20041 Screw 4

55 6091 Screw 1

56 4274 Nut 3

57 325 Nut 3

58 5191 Nut 4

59 4292 Washer 6

61 3588 Washer 12

62 67272 End plate 2

325 325 Nut 1 Note 2

20202 20202 Screw 1 Note 2

Note 1: Between s/n 70581 and 71336 most units supplied with one aperture plate. Ceph image sizes 18x24cmAV/SV and 24x30cm AV.

Note 2: New adjustment from s/n 71438.

Note 3: If old collimator (units 70000 - 70060) will be replaced with new one, then collimator flange code67295 is needed.

Note 4: Filter form changed from s/n 78386 new code 67358.

Note 5: From s/n 79968 without black paint.


5 Rotating unit

5.5.2.7 OC100, JT, collimator, (8x10, 10x12) inch, Japan, from unit s/n 70714


67270 Collimator OC100, JT (8x10, 10x12)inch, Japanfrom unit s/n 70714




5 68979 Cable CC1 1

6 67276 Aperture plate, left 8x10in SV/AV and 10x12in AV 1 Note 1

7 67277 Aperture plate, right 8x10in SV/AV and 10x12inAV

1 Note 1



62

5 Rotating unit



16 67261 Rod 1

21 68122 Knob 2

26 67293 Collimator flange 1



36 67284 Rod 1

39 6277 Pin 3


42 6698 Spring 1

43 21279 Spring 1

44 21477 Screw 2


47 6699 Screw 7

48 2757 screw 2

51 2656 Screw 4

53 20041 Screw 4

55 6091 Screw 1

56 4274 Nut 3

57 325 Nut 3

58 5191 Nut 4

59 4292 Washer 6

61 3588 Washer 12


325 325 Nut 1 Note 2

20202 20202 Screw 1 Note 2

Note 1: Between s/n 70581 and 71336 most units supplied with one aperture plate. Ceph image sizes 8x1 0inSV/AV and 10x12in AV.




5 Rotating unit

5.5.2.8 Collimator, OC100, JT, (8x10SV/AV, 10x8AH) in, USA, from s/n 70458


67292 Collimator OC100, JT (8x10SV/AV, 10x8AH)in,USA from unit s/n 70458




5 68979 Cable CC1 1

6 67287 Aperture plate, left 8x10in SV/AV and 10x8in AH 1 Note 1

7 67291 Aperture plate, right 8x10in SV/AV and 10x8in AH 1 Note 1



16 67261 Rod 1

62

5 Rotating unit



21 68122 Knob 2

26 67293 Collimator flange 1



67358 Soft tissue wedge Note 3

36 67284 Rod 1

39 6277 Pin 3


42 6698 Spring 1

43 21279 Spring 1

44 21477 Screw 2


47 6699 Screw 7

48 2757 screw 2

51 2656 Screw 4

53 20041 Screw 4

55 6091 Screw 1

56 4274 Nut 3

57 325 Nut 3

58 5191 Nut 4

59 4292 Washer 6

61 3588 Washer 12


325 325 Nut 1 Note 2

20202 20202 Screw 1 Note 2

Note 1: Between s/n 70581 and 71336 most units supplied with one aperture plate. Ceph image sizes 8x1 0inSV/AV and 10x8in AH.


Note 3: Filter form changed from s/n 78386.



5 Rotating unit

5.5.2.9 Collimator, OP100 OT


67315 Collimator OP100 OT

325 Nut 6

331 Washer 16

365 Allen screw 2

2656 Screw 4

2735 Screw 1

2757 Screw 3

3202 Screw 2

3588 Washer 15

4274 Nut 3

4292 Washer 6

6091 Screw 1

5 Rotating unit



6631 Washer 3

6698 Spring 1

6699 Screw 17

20014 Micro switch 3

20041 Screw 8

20202 Screw 1

20231 Bearing 3

20508 Screw 2

21477 Screw 2

67296 Aperture plate 1 Note 1

67261 rod 1

67262 Fixing angle 1

67264 Main frame 1

67266 Guide frame 1

67272 End plate 1

67347 End plate 1 Note 2

67273 Upper frame 1

67274 Lower frame 1

67275 Flange 1

67289 Collimator frame 1

67293 Collimator flange 1

67301 Sliding frame 1

67302 Primary slot plate OP 100 JT 1

67307 Front filter 1

67308 Back filter 1

68122 Knob 1

68264 Primary slot plate, OP 1 00QA, JT 1

68979 Cable CC1 1

Note 1: Ceph slits are not used here.

Note 2: From s/n 74053.


5 Rotating unit

5.5.2.10 Collimator, OC100 OT


67316 Collimator OC 100 OT, 1 8x24S V, 1 8x24AV Note 1

67319 Collimator OC 100 OT, 1 8x24SV,24x30AV Note 1

67317 Collimator OC100 OT, 8x10SV,8x10AV Note 1

67318 Collimator OC100 OT, 8x10SV,10x8AH Note 1

67320 Collimator OC100 OT, 8x10SV,10x12AV Note 1

325 Nut 6

331 Washer 16

365 Allen screw 2

366 Allen screw 1

5 Rotating unit



924 Rod 1

2425 Pin 1

2656 Screw 4

2735 Screw 1

2751 Screw 1

2757 Screw 3

3202 Screw 2

3588 Washer 15

3886 Star lock 1

4291 Screw 2

4274 Nut 3

4292 Washer 6

6091 Screw 1

6277 Pin 2

6631 Washer 3

6698 Spring 1

6699 Screw 17

20014 Micro switch 3

20041 Screw 8

20185 Pillar screw 1

20202 Screw 1

20231 Bearing 3

20508 Screw 2

20279 Spring 1

21477 Screw 2

21572 Retainer ring 1

21593 Nut 1

21594 Allen screw 1

65623 Nut 4

67213 Filter 1

67255 Frame 1

67256 Axle 3

67257 Pole 1

67310 Aperture plate, 18x24SV,24x30AV,TOMO,R 1

67309 Aperture plate, 18x24SV,24x30AV,TOMO,L 1

67300 Aperture plate, 1 8x24SV/AV,TOMO,R 1

67299 Aperture plate, 1 8x24SV/AV,TOMO,L 1

64415 Aperture plate TOMO 18x24 SV/AH left 1

64414 Aperture plate TOMO 18x24SV/AH right 1

67305 Aperture plate, 8x10in SV/AH,TOMO, L 1

67306 Aperture plate, 8x10in SV/AH,TOMO,R 1


5 Rotating unit


67321 Aperture plate, 8x10inSV,10x12inAV,TOMO,L 1

67322 Aperture plate, 8x10inSV,10x12inAV,TOMO,R 1

67296 Aperture plate, 8x10inSV/AV,TOMO,L 1

67297 Aperture plate, 8x10inSV/AV,TOMO,R 1

67261 Rod 1

67262 Fixing angle 1

67263 Frame plate 1

67264 Main frame 1

67266 Guide frame 1

67267 Wedge frame 1

67268 Lever 1

67269 Cam 1

67271 Soft tissue wedge 1

67358 Soft tissue wedge

67272 End plate 2

67273 Upper frame 1

67274 Lower frame 1

67275 Flange 1

67283 Rod 1

67284 Rod 1

67285 Axle 1

67288 Sliding plate assembly 1

67289 Collimator frame 1

67290 Soft tissue wedge assembly 1

67293 Collimator flange 1

67301 Sliding frame 1

67302 Primary slot plate, OP 100 JT 1

67304 Block 1

67307 Front filter 1

67308 Back filter 1

67314 Sliding carriage assembly 1

68122 Knob 1

68264 Primary slot plate, OP 1 00QA, JT 1

68979 Cable CC1 1

Note 1: Collimators are equal, image sizes are varied by using different aperture plates. Tube head front coverhas matching decals.

Note 2: Filter form changed from s/n 78386.

5 Rotating unit


5.6 Cassette rack

5.6.1 Cassette rack, unit’s s/n 70000-70231


186 65483 Cassette rack cast 1

193 65487 Rack support fork 1

194 65486 Slide rod Ø 12 1



65543 Micro switch support 2

196 65518 Cable holder 2

197 65484 Slide rod Ø12 1


5 Rotating unit


205 65563 Top lock piece 2

206 65562 Bottom lock piece 2

207 21239 Drive belt 2

210 65488 Guiding roll 4

31024 Motor bushing 4

217 2395 Screw 2

219 65473 Mounting bar 1

220 65509 Rack trim cover, left 1

221 65507 Secondary plate “JS” 1 Note 1

65631 Secondary plate “JT” 1 Note 2

222 65508 Rack trim cover, right 1

223 65501 Slide rod Ø 12 1

226 65547 Sensor for cassette 1

227 65599 Knob L 1

229 65646 Cassette friction piece 1

230 65597 Tunnel end, L 1

232 20478 Spring 2

233 65596 Cassette tunnel 1

234 65472 Slide bushing 1

235 65569 Mounting plate for micro switches 1


237 65601 Knob R 1

238 65598 Tunnel end, R 1

250 65829 Cassette rack motor assembly with gear 1

251 60122 AEC-board 1

255 9353 Spring 1

260 65829 Cassette motor with drive wheel 1

Note 1: Used in the assembly code 65475.

Note 2: Used in the assembly code 65500.

5 Rotating unit


5.6.2 Cassette rack, from unit s/n 70232


65475 Cassette rack holder, model “JS” Units s/n 70000-70146

65500 Cassette rack holder, model “JT” Units s/n 70147-70231

65600 Cassette rack, complete Units s/n 70232-70999

65705 Cassette rack, MK2, complete Units from s/n 71000-

1 65675 Cassette tunnel assembly 1 Note 1, section 5.4

1 65590 Cassette tunnel assembly 1 Note 2, section 5.4

2 65585 Cassette lifting assembly 1 Section 5.6

3 65580 Cephalostat locking assembly 1 Section 5.7

4 65575 Lower bushing chassis 1 Section 5.4

5 60122 AEC board, complete 1 Section 5.5

6 60147 Cassette opto sensor 1 Note 3

7 65692 Sliding bearing assembly 1 Note 1

65691 Sliding bearing assembly 1 Note 2

8 65588 Sliding surface 1

9 65484 Slide rod, left 1

10 65486 Slide rod, right 1

12 65631 Secondary plate, JT 1

65507 Secondary plate, JS 1

13 65627 Trim cover, right 1

14 65628 Trim cover, left 1

From unit s/n 70232 1 7 6

2

8

27

5

15

9 310

3034

4

14

1213


5 Rotating unit




30 65289 Motor with gear 1

34 9353 Spring 1

Note 1: Units s/n 70337 - 70341, 70345 and from s/n 70347. From unit s/n 72442 and up Sensor lever andSensor holder changed, new codes: Sensor lever, code 65684 and Sensor holder code 65685. From s/n 77012opto sensor fixing changed higher.

Note 2: Units s/n 70232 - 70336, 70342 - 70344 and 70346. Old Sensor Lever code 65619 and Sensor holdercode 65674.

Note 3: From s/n 77012 opto type changed.

5.6.3 Cassette rack, from unit s/n 70232


43 21509 Screw 2

54 4323 Screw 1

58 5191 Nut 2

63 2395 Washer 1

64 2396 Washer 2

72 5277 Washer 2

73 301 Screw 2

From unit s/n 70232

130127 111126 129

100 9699 192

97

107

93

94 102

110 116 103 193

72 58

145

64 73

7554 63

159 157

153156158

43

5 Rotating unit



75 65664 Spacer 1

93 65613 Knob right 1 Note 1

94 65614 Knob left 1 Note 1

96 65678 Tunnel end, left 1 Note 1

65504 Tunnel end, left 1 Note 2

97 65677 Tunnel end, right 1 Note 1

65503 Tunnel end, right 1 Note 2

99 65676 Slide rod 1 Note 1

65501 Slide rod 1 Note 2

100 20478 Spring 2

102 21384 Screw 2

103 20604 Screw M3x12 2

103 22505 Screw M3x14 2

107 4422 Screw 2

110 65499 Motor axle 1

111 21489 Coupling 1 Note 3

116 20905 Cassette rack motor 1

126 3046 Screw 2

127 293 Screw 4

129 3588 Washer 2

130 2395 Washer 4

145 21413 Spring 2

153 20959 Bearing 1

156 3046 Screw 1

157 295 Screw 2

158 3588 Washer 1

159 2395 Washer 2

192 6698 Spring 1

192 22284 Spring 1 Note 4

193 65588 Sliding surface 1

Note 1: Units s/n 70337 - 70341, 70345 and from s/n 70347 Cassette tunnel system with opto sensors. Sliderod diameter 10 mm. Groove added that the cassette with pins cannot be inserted backwards.

Note 2: Units s/n 70232 - 70336, 70342 - 70344 and 70346 Slide rod diameter 12 mm.

Note 3: From s/n 73959 coupling no more used.



5 Rotating unit

5.6.4 Cassette rack, OP/OC100 CR


65701 Cassette rack CR, complete Note 1

65706 Cassette rack CR, MK”, complete Note 2

65869 Cassette rack with AEC Note 4

1 65702 Cassette tunnel assembly 1

2 65703 Cassette lifting assembly 1

3 65580 Cassette locking assembly 1

4 65575 Lower bushing chassis 1

5 3030 Screw M4x16 1

6 20041 Screw M4x22 1

7 65691 Sliding bearing assembly 1

8 3588 Washer 2

9 65484 Slide rod, left 1

10 65486 Slide rod, right 1

11 65659 Bushing 1

12 65631 Secondary plate, JT 1

12 65917 Secondary plate OP100 OT, CR From s/n 76643

13 65661 Trim cover, right 1

14 65660 Trim cover, left 1


20 20905 Motor 1

30 65829 Cassette motor with drive wheel 1

34 9353 Spring 1

CASSETTE RACKOP100 CR

1 7

4041

2

13

5 8

3011

6 8

20

15

3

9 10 4 14 12

5 Rotating unit



40 65777 Knob right 1

41 65778 Knob left 1

42 65748 Cassette adapter 1 Note 3

43 69001 Adapter X116 1

23582 Spring for cable 19A 1 From s/n 75714

Note 1: For units s/n 70000-70999 without CE option and CR upgrade kits.

Note 2: From unit s/n 71000 with CE option and CR upgrades.

Note 3: Optional adapter for 15x30cm cassette.


Note 5: From s/n 76459 secondary plate made narrower.

Only special order delivery.

5 . 7 A E C B o a r d


60122 AEC Board 1


5 Rotating unit

5.8 Cassette lifting assembly2


65585 Cassette lifting assembly From s/n 70232

1 3689 Screw 2

2 65718 Wheel 4

3 65552 Adjusting block 2

4 3556 Screw 2

5 4291 Washer 4

6 615 Screw 4

7 65499 Motor drive axle 1 Note 2

8 31024 Motor bushing 4

9 21489 Clutch 2 Note 1

10 20905 Cassette rack motor 1

15 3046 Screw 2

16 3588 Washer 2


21 21112 Washer 2

22 323 Nut M8 2

23 65499 Motor drive axle 1

65925 Motor drive axle 1

Note 1: From s/n 73959 coupling (clutch) no more used. From s/n 74787 clutch used.

Note 2: From s/n 76644 code 65928 axle replaces 65499 motor drive axle.

5 Rotating unit


5.9 Cephalostat lock assembly


189 65511 Lock pin 1

190 65512 Lock chassis 1

191 65513 Locking wedge 1

192 21389 Spring 1

200 293 Screw M6x20 2

201 2395 Washer 2

202 6091 Screw 1

203 321 Screw M4x6 1

210 20712 Screw M4x4 2

211 65594 Locking wedge 1

212 321 Screw 1

213 65593 Chassis 1

214 65645 Rod 2

215 21413 Spring 2

216 21112 Washer 2

217 21431 Locking ring 2

Fromunit s/n70232

203

Units

s/n 70000 - 70035

213

214

215

210

211

212

Units

s/n 70036 -70231

216

217

8

6

7

5

2

4

1

2

3

5 Rotating unit



1 65594 Locking wedge 1 Units s/n 70232-70999

1 65644 Locking wedge 1 Units from s/n 71000

2 321 Screw 3

3 65645 Rod 2

4 21413 Spring 2

5 21431 Locking ring 2

6 21112 Washer 2

7 65511 Lock pin 1

8 65642 Frame 1 Note 1

Note 1: From s/n 76811 place for C1 8 cable larger from s/n 79144 machinery in frame changed.

6 Cephalostat


6 Cephalo stat


1-9 Cephalostat assembly, s/n 70000-70051 Section 6.1

1-9 Cephalostat assembly, s/n 70052-7 1437 Section 6.2

1-9 Cephalostat assembly, from s/n 71438-72263 Section 6.3

1-9 Cephalostat assembly, from s/n 72264 Section 6.4

1 68105 Cephalostat arm assembly

2 68085 Cephalostat body assembly

3 68095 Cassette holder assembly

4 68090 Cephalostat rotating assembly

5 68260 Ear holder movement complete

7 6512 screw, 2pcs

4261 Alternative screws, 2 pcs

8 68265 Nose support assembly

( 9 )Installation accessories Section 6.7

( 1 0 )Patient positioning accessories Section 6.8

Cephalostat packing Section 6.5

9228 Ear holder, 4-hole, complete Section 6.6

14

5

3 26

8 7

6 Cephalostat


6.1 Cephalostat assembly, unit’s s/n 70000-70051


1 293 Screw 4

2 334 Washer 4

3 3689 Screw 4

4 68105 Ceph arm complete 1

5 68260 Ear movement complete 1

6 68265 Nose support assembly 1

7 50180 Ear holder complete 1

8 6512 Screw 4

9 8915 Hygiene protectors 20 pcs 1

10 6471 Ear olive 2

11 6517 Cap 2

13 21376 Bushing Glykodur 1

16 6 8 9 8 0 Cephalostat cable CC2 1

6 Cephalostat



21 8668 Nose support 1

22 301 Screw M8x25 1

23 6481 Adjusting support 1

24 2395 Washer 2

25 3689 Screw M6x25 2

26 2746 Screw M3x8 2

27 6482 Plate 1

31 68128 Adjusting plate 2

32 366 Screw 2

34 302 Screw 4

35 335 Washer 4

36 68249 Plate 1

37 68229 Trim cover 1

501 68169 Top cover 1

502 68159 Eccentric chassis 1

503 68161 Bushing 1

504 68162 Eccentric shaft 1

506 68160 Holder 1

507 68126 Ceph body 1

509 60110 Ceph soft tissue display board 1

510 4363 Rubber ring 16

511 6461 Axle 2

513 68097 Sliding bracket 2

515 6725 Axle support 2

517 68102 Cassette holder body 1

518 68099 Cassette retainer 1

519 68137 Back plate (18x24 A/S 24 x 30 A) 1

69193 Back plate (8x10 in A/S 10x12 in A) 1

520 68101 Bottom plate 1


539 68165 Rotating chassis 1

540 68156 Rubber ring 1

541 68154 Bushing 1

542 68153 Axle 1

543 68151 Locking housing 1

544 68152 Wheel 1

545 68149 Lever 1

547 68134 Bearing housing 1

548 6442 Rod 2


6 Cephalostat

6.2 Cephalostat assembly, unit’s s/n 70052-71437


68100 Cephalostat Note 4




18 68982 Cable CC4 1

19 1761 Scale 1

20 68981 Cable CC3 1

21 8668 Nose support 1

22 1680 screw M8x25 1


24 2395 Washer 2

6 Cephalostat



25 3689 Screw M6x25 2

26 2746 Screw M3x8 2

27 6482 Plate 1

28 3689 Screw 4

29 302 Screw 4

30 335 Washer 4

31 21376 Bushing Glykodur 1


33 366 Screw 2

34 293 Screw 4

35 334 Washer 4

36 68249 Plate 1


38 21312 Potentiometer 1

39 60143 Up/down switch 1

40 68137 Back plate (18x24, 24x30)mm 1 Note 1

68296 Back plate (18x24, 24x30)mm 1 Note 2

68193 Back plate (8x10, 10x12) inch 1 Note 2

68312 Back plate (8x10, 10x8) inch 1 Note 3

41 4291 Washer 1

42 20041 Screw 1

43 68211 Limiter 1

44 68219 Rubber brake 1

45 68250 Screw kit for Cephalostat, includes parts 23-36 1

Note 1: Unit s/n 70000-705 99.

Note 2: From unit s/n 70560, cassette holder 2cm longer.

Note 3: From unit s/n 70458, cassette holder 2cm longer.

Note 4: Image sizes 1 8x24cm AV/SV and 24x30cm AV. Cassette back plate changed from unit s/n 70560.

N o t e 5 : I m a g e s i z e s 8 x 1 0 i n A V / S V a n d 1 0 x 1 2 i n A V .

Note 6: Image sizes 8x10 in AV/SV/AH.


6 Cephalostat

6.3 Cephalostat assembly unit’s s/n 80052-71437


1 68085 Cephalostat body complete 1

2 68090 Rotating chassis compete 1

3 68095 Cassette holder complete 1

4 68105 Cephalostat arm complete 1


6 68265 Nose support complete 1


8 6512 Screw 2

9 8915 Hygiene protectors 20 pcs. 1

10 6471 Ear olive 2

11 6517 Cap 2

12 69973 Magnification scale sticker 1

13 60110 Ceph soft tissue display 1

14 68228 Ceph cover 1

15 21443 Screw 4

6 Cephalostat



16 68980 Cable CC2 1

6.4 Cephalostat assembly units, s/n 71438-72263






2 68090 Rotating chassis compete 1

3 68370 Cassette holder complete 1





8 6512 Screw 2


10 6471 Ear olive 2


6 Cephalostat


11 6517 Cap 2

12 69973 Magnification scale sticker, L+R 1

68292 Magnification scale sticker R

68293 Magnification scale sticker L



15 21443 Screw 4

16 68980 Cable CC2 1

20 68324 Back plate (18x24, 24x30)cm 1

68323 Back plate (8x10, 10x12)inch, Japan 1

68325 Back plate (8x10, 10x8)inch, USA 1

28 3689 Screw 4

29 302 Screw 4

30 335 Washer 4

34 293 Screw 4

35 334 Washer 4

36 68249 Ceph adjusting piece 13x80 1


45 68348 Screw Kit for cephalostat( parts 28, 29,36)

30, 34, 35, 1

Note 4: Image sizes 18x24cm AV/SV and 24x30cm AV.

Note 5: Image sizes 8x10 in AV/SV and 10x12 in AV.

Note 6: Image sizes 8x10 in AV/SV/AH.

6 Cephalostat


6.5 Cephalostat assembly, units from s/n 72264


6 Cephalostat

47

68224

68318

68383

68317

23

25

24

22

6 Cephalostat


8668






2 68090 Rotating chassis complete 1

3 68095 Cassette holder complete (short without back plate) 1

68345 Cassette holder complete (long without back plate) 1 Note 12





68409 Ear holder complete 2 Note 7

8 6512 Screw 2 Note 3


10 6471 Ear olive 2 Note 7

11 6517 Cap 2 Note 7


6 Cephalostat


12 69973 Magnification scale sticker, L+R 1

68292 Magnification scale sticker R

68293 Magnification scale sticker L



15 21443 Screw 4

16 68980 Cable CC2 1


18 68982 Cable CC4 1

20 68324 Back plate (18x24, 24x30)cm 1

68323 Back plate (8x10, 10x12)inch, Japan 1

68325 Back plate (8x10, 10x8)inch, USA 1

20 68404 Back plate short (1 8x24, 24x30)cm 1 Note 11

68405 Back plate short (8x10, 10x12)inch, Japan 1 Note 11

68406 Back plate short (8x10, 10x8)inch, USA 1 Note 11

22 1680 Screw M8x25 1


24 2395 Washer 2

25 3689 Screw M6x25 2

26 2746 Screw M3x8 2

27 6482 Plate 1

29 1719 Screw 4

30 335 Washer 4

34 297 Screw 4

35 334 Washer 4

36 3018 Screw 4 Note 8

37 68229 Cover

38 22587 Potentiometer 1 Note 10

39 60143 Up/Down switch 1

40 68427 Potentiometer kit 1 Note 9

4363 Rubber ring 6

68412 Sliding carriage 1

6516 Bearing 4

68117 Potentiometer holder 1

22587 Potentiometer 1

41 4291 Washer 1

42 20041 Screw 1

43 68211 Limiter 1

44 68219 Rubber brake 1

46 68981 Cable CC3 1

47 3075 Screw 8

6 Cephalostat



8668 Nose support 1

Note 3: Alternative screw 4261

Note 4: Image sizes 18 x 24 cm AV/SV and 24 x 30 cm AV

Note 5: Image sizes 8 x 10 in AV/SV and 10 x 12 in AV.

Note 6: Image sizes 8 x 10 in AV/SV/AH.

Note 7: From s/n 72647 material changed. Code 68409 replaces code 50180.

From s/n 74708 Ear holder construction more rigid.

Note 8: From s/n 72371 the 4 screws replace the adjustment piece code 68249.

Note 9: For unit’s s/n 73268 and lower if the potentiometer old type 21312 must be changed.

Note 10: From s/n 73269 and up.

Note 11: For special model 68403, Lower Ceph Cassette Holder. This holder is 2 cm lower than the standardconfiguration.

Note 12: Cable rings made larger from s/n 74854.

6.6 Cephalostat cardboard box packing, from s/n 71617

Laatik3a.


6 Cephalostat


1 9228 Ear holder, 4-holes, complete 1 Note 2

2 6512 Screw 2

3 68589 Ear holder 1 Note 3

4 68588 Ear screw 1 Note 3

Note 1: Special ear holder with 4 holes (additional holes 20 mm, 40 mm and 60 mm higher) allowing patientpositioning to see cervical spine.

Note 2: 63439 Ear holder kit, extended. Extension parts 5mm, 10mm, 25mm.

Note 3: Material modificated thinner.

6.8 Installation accessories

6.8.1 Up to s/n 72370

6.7 Ear holder, 4-holes

3

2

4

1

6 Cephalostat


SCREW S

WASHERS


6 Cephalostat


1-8 68250 Installation accessory set I, complete

6 Cephalostat



1 68128 Adjustment piece 2



3 21376 Bushing 1 Note 3

4 335 Washer 8.4 4



6 68249 Ceph adjustment piece 13x80 1 Note 4

7 334 Washer 6.4 4

8 293 Screw M6x20 4

Note 1: All OC 100 models manufactured until October 1993.

Note 2: All OC 100 models manufactured from November 1993.

Note 3: Cephalostat arm fixing changed, bushing not used from s/n 72240.

Note 4: To s/n 72370.

6 Cephalostat


6.8.2 From s/n 72371


4-36 68428 Installation accessory set II, complete

4 335 Washer 8.4 4

5 302 Screw M8x30 4

7 334 Washer 6.4 4

8 293 Screw M6x20 4

36 3018 Screw 4

6.9 Patient positioning accessories


1 7453 Nose support cover 100 pcs 1

2 8915 Hygiene protectors 20 pcs 1

1

2

7 Patient positioning accessories




1 62988 Bite fork rod, 71 mm 1 Note 11

2 62985 Bite fork rod, 56 mm 1 Note 12

62958 Bite fork rod, 80 mm 1

3 8878 Bite fork, 10 pcs 1 Note 5

3 62942 Bite fork OP 100, 10 pcs 1 Note 6

4 6644 Bite fork coat, 500 pcs 1

5 62884 Nose support 1 Note 1

62906 Nose support 1 Note 2

6 62903 Nose support long 1 Note 1

62904 Nose support, long 1 Note 2

7 7453 TMJ support coat, 100 pcs 1

8 69962 TMJ pointer 1 Note 3

8 60477 TMJ pointer, model A 1 Note 4

8 64694 TMJ pointer, OT 1 Note 8

9 6722 Chin support 1

10 62875 Chin rest 1 Note 14

10 68758 Chin rest 1 Note 14

11 7451 Chin rest coat, 100 pcs 1 Note 10

12 62895 Sinus rest 1 Note 14

12 68759 Sinus rest 1 Note 14

13 50076 Child adapter 1

14 62965 Edentulous bite positioner 1 Note 13

20

18 19




15 64665 TMJ angle indicator 1 Note 7

16 62943 TMJ chin rest 1 Note 7

17 62934 Chin rest height adjustment plate 1 Note 9

18 62945 Bite plate, large 10 Note 8

62977 Bite plate large, 100 psc 1 Note 8

62971 Bite plate, small 10 Note 8

62976 Bite plate small, 100 pcs 1 Note 8

20 64703 Occlusal film holder 1

21 63335 Ortho Trans Magnification scale 1

22 63008 Double ruler 1

Note 1: Black plastic piece. Unit’s s/n 70000 - 70202, this spare part no more available.

Replacement:

62884 Nose support short = 62906 + 62905 (nose support bushing).

62902 Nose support long = 62904 + 62905 (nose support bushing).

Note 2: Gray plastic piece. Units from s/n 70203.

Note 3: Metal/plastic. Units s/n 70000 - 70240.

Note 4: Plastic piece. Units from s/n 70241.

Note 5: Units s/n 70000 - 70682.

Note 6: Units from s/n 70683.

Note 7: Used with Ortho TMJ option.

Note 8: Used with Ortho Trans units.

Note 9: Optional part to elevate sinus and chin rest.

Note 10: New size (8x10cm) from s/n 72410

Note 11: Old code was 2648

Note 12: Old code was 4401

Note 13: From s/n 74435 the ball stainless steel.

Note 14: From s/n 79812 Chin and sinus rests shortened.

8 Electrical spare parts



8.1 Printed circuit boards


1 60122 AEC Board 1 Note 4

2 60112 CPU Board 1 Note 1

3 60110 Ceph soft tissue display board 1

4 60143 Ceph up/down switch 1

5 61160 Control panel complete 1

6 60147 Cassette opto sensor 1

7 60108 Patient positioning panel 1

8 60123 interface Board 1 Note 5

60166 Interface Board, OT 1 Note 2

9 60113 Power Supply Board 1 Note 3

10 60115 Inverter Board 1 Note 6

11 60114 Filament Control Board 1 Note 7

12 60134 Head Support Lock 1


Note 1:

v1.1: Diode D15 added. v1.2: Connectors X13 and X14 added and R23 short circuited. v1.3: Connector X3,pin 9 and 10. +25V and ground added.



v1 .4: From units 72048. Units with OT-system or from s/n 72000 with User program v1 .2.07, Serviceprogram v.1.2.07 and ICD25 v2.0.0. or higher, ICD4 furnished on the board for Trophy Digipan option.CE models use version v1 .4 or higher.

v1.5: D15 improved. From s/n 72184. V 1.6 R1 8 value changed, watch log test improved. April 2000. v 1.7 from s/n 80359, micro switch specification 1mA current.

Note 2: Units with Ortho Trans-system or CE-models from s/n 72000. From s/n 74218, v 1.4. This versionmust have ICD 1,6 and 10 code 60171 program version v.2.0.1.

Note 3: Version v1.1 with 4 switches S1,S2,S3 and S4.Version v1.3 Switches replaced with a jumperconnector. Boards are interchangeable. Units s/n 73994-74023 and from s/n 74139 , version v 1.4, D4 typechanged. v 1.5 from s/n 77511 and board s/n 11470 resistance R6 changed.

Note 4: v1.3 units 7255 1,72600,72822 and from s/n 72825. AD546 replaced with OPA 124P. V 1.4 from s/n79348 component changes ICA1, R3, R11 and R12.

Note 5: Units s/n 70000 - 71999 and units without Ortho Trans system.

Note 6: From s/n 78236 v1.5 capacitor C7 type changed. From s/n 80156 qualifying text added from s/n80217 v1 .6. The parallel resistor R4 of the current indicator leds did not have “enough power handlingcapacity” when the generator used high kV and mA values. The leds have been moved parallel to the coil L1and the resistance R5 have been replaced with R74.

Note 7: V 1.3 from board s/n 465.



8.2 Connectors



8.3 Transformers & cable sets


1 68977 Transformer TF1 1

2 68976 Transformer TF2 1

3 68952 Cable C1 1

4 68953 Cable C2 1

5 68954 Cable C3 1

6 68955 Cable C4 1

7 68956 Cable C5 1 Note 11

8 689966 Cable C6 1 Note 12

8 68957 Cable C6 1

9 68958 Cable C7 1

10 68959 Cable C8 1

11 68960 Cable C9 1




12 68961 Cable C10 1

13 68962 Cable C11 1

14 68963 Cable C12 1 Note 4

15 62094 Cable C13 1 Notes 1, 7

16 68965 Cable C14 1

17 68966 Cable C15 1

18 68967 Cable C16 1 Note 6

19 68968 Cable C17, OP-collimator 1

20 68969 Cable set (groundings) 1

21 68971 Cable SC 1 1

22 68972 Cable SC 2 1

23 68973 Cable SC 3 Control panel 1

24 68974 Cable SC 4 1 Note 9

25 68975 Cable SC 5 1 Note 9

26 68978 Choke coil cable L1 1

27 68966 Cable C 19 (CR cassette holder) (without AEC) 1

28 68970 Light projector cable 1

29 68979 Cephalostat cable CC 1, OC-collimator 1

30 68980 Cephalostat cable CC 2 1

69048 Cephalostat cable CC” 1 from s/n 75557

68049 Grounding cable 1 From s/n 75557



33 68992 X 118 extension cable 1 Note 2

34 68993 Cable C18 1 Note 10

35 69961 Remote exposure button, complete 1 Note 3

36 69000 Cable C20 1 Note 8

37 68995 Adapter cable 1 Note 13

38 68997 Extension cable for C13 X114 1 Note 1

39 68999 Cable for film marker CPU, X12-X106 1 Note 5

40 69001 Adapter for X116 for OP/OC 100 CR 1

41 69013 Cable C34, from X3 to X106 1

68994 For larger projector it 2 projectors are used (sharingcable)

1

69040 Cable 1 9A for CR unit with AEC 1 From unit s/n 75714

Note 1: Cable length modified in November 1993. From s/n 71837 ready for Ortho Trans-system.

Note 2: Used to modify FH light for right handed operation. Needed with all OP100 and OC100 models withs/n 70000 - 70150, if FH light is modified. All models from s/n 70151 have an extension cable equipped.

Note 3: Set consists of the exposure button, 10 m cable and the holder with mounting screws.



Note 4: Connection for ORTHO ID made units s/n 70627-70629,70631-70638,70681,70684-70687 and70701 -->

Note 5: Adapter for ORTHO ID for units below s/n in NOTE 4.

Note 6: From s/n 71683 the cable is integrated to the tube head.

Note 7: Readiness for Ortho Trans update from s/n 71837. From s/n 72102 cable improved so that all wiresTeflon coated except wire between X4-X38. From s/n 72102 cable assembly improved(Teflon coated cables).From s/n 77346 head support bracket + cable C 13 construction changed. When ordering spare part for olderunit use code 62094. From s/n 78304 insertion between X109 and X30 improved.

Note 8: Optional cable (short straight, for control panel)

Note9: Units 70000 - 70231

Note 10: From s/n 70232. This cable C18 replaces the cables SC4 and SC5 codes 68974 and 68975. From s/n77511 cable length changed longer.


Note 12: Units s/n 70000 - 70376




8.4 Micro switches, light bulbs and fuses


1 20014 Micro switch 12 For OP100

20014 Micro switch 15 For OC100

2 21245 Micro switch 1 Only OC100

3 20912 Lamp 12V/20W 3

4 6027 Lamp 12V/5W 2

5 20045 Fuse 15 AT 2

6 20154 Fuse 10 AT 2

20204 Fuse 16 AFF 1 Note 1

S110

11




8 20146 Fuse 6.3 AT 2 Note 2

9 21275 Fuse 2 AT 1

10 20367 Main switch 1

11 22460 Micro switch, control panel 1 Note 3

Note 1: Used with inverter board v 1.3, V1.4 from s/n 71149.

Note 2: Fuse 10 AT should be used if there are two FH-and layer projectors in the unit.


8.5 CPU software


1 60130 User program 1

V 1.2.01

V1.2.05 Note 5

V1.2.06 Note 6

V1.2.07 Note 4

V1.2.14 From s/n 79858

V1.2.16 From s/n 81168

2 60137 Service program 1

V1 .2.01

V1.2.05 Note 5

V1.2.06 Note 6

V1.2.07 Note 4

V1.2.14 From s/n 79858

V1.2.16 From s/n 81168

3 60129 ICD 25, PAL 1

V1.0.0

V1. 1.0

60172 ICD 25 PAL 1

V2.0.0 Note 4

60173 ICD 25, PAL 1

V2. 1.0

4 21040 ICD 8, EEPROM 1

Note 4: Units with Ortho Trans system or CE units from s/n 72000.

Note 5: Units 71057-71754.

Note 6: Units 71755-71999.



8.6 Software & board version references

This table explains which units, programs, boards and software’s are compatible and permitted. In case ofmischoice your unit does not work correctly.

OrthoTrans

Ortho TMJ/Ortho Zone

Digipan Ortho IDInterface board & CPU PAL

(ICD25) versionSoftwareversion

No No No No 60123 & 1.0.0, 60123 & 1.1.0 1.2.01-16

60166 & 2.0.0, 60166 & 2.1.0

Yes 60123 & 1.1.0 1.2.06

60166 & 2.1.0

60123 & 1.0.0, 60123 & 1.1.0 1.2.07 - 1.2.16

60166 & 2.0.0, 60166 & 2.1.0

Yes > 60123 & 1.0.0 1.2.07- 1.2.16

60166 & 2.0.0

Yes No No 60123 & 1.0.0, 60123 & 1.1.0 1.2.06 - 1.2.16

60166 & 2.0.0, 60166 & 2.1.0

Yes 60123 & 1.1.0 1.2.06

60166 & 2.1.0

60123 & 1.0.0, 60123 & 1.1.0 1.2.07 -1.2.16

60166 & 2.0.0, 60166 & 2.1.0

Yes ----> 60123 & 1.0.0 1.2.07 - 1.2.16

60166 & 2.0.0

Yes ----> No ----> 60166 & 2.0.0 1.2.07 - 1.2.16

60166 & 2.1.0

Yes > 60166 & 2.0.0 1.2.07 - 1.2.16

OPTION MUST HAVE

DIGIPAN => Software v. 1.2.07 or 1.2.14 and PAL v. 1.0.0 or

2.0.0

Ortho ID => Software v. 1.2.06 and PAL v. 1.1.0 or 2.1.0

Software v. 1.2.07 and PAL v. 1.0.0 or 1.1.0 0r2.0.0 or 2.1.0.

CPU v.1.0-1.2 and cable 68999 or CPU v 1.3 orhigher

Interface board 60166 => PAL v. 2.0.0 or 2.1.0

Ortho Zone or Ortho TMJ => Software v. 1.2.06, 1.2.07 or 1.2.14 all CPUversions

Ortho Trans => Interface board 60166 and Software v. 1.2.07 -

1.2.16

(and PAL v. 2.0.0 or 2.1.0). All CPU versions.




9 Service tools


1-13 60522 Maintenance Kit A Note 1

1 65630 OP 100 Fluorescent tool (for narrow slit “JT”) 1

69915 OP 100 Fluorescent tool (“JS”) 1

2 69980 Ball & 2 pin phantom 1

3 20912 Lamp 12 V/20 W 1

4 6027 Lamp 12 V /5 W 1

5 20045 Fuse 15 AT 10

6 20154 Fuse 10 AT 10

7 20204 Fuse 16 AFF 10

8 21275 Fuse 2 AT 10

9 61215 Tool kit-Incl. Allen wrenches 1.5, 2, 3, 4, 5 and 6 mm

1

10 69904 Installation Manual USA 1 Note 5

11 69902 User Manual USA 1 Note 5

12 69913 Technical Support Manual 1 Note 5

63344 Service Manual 1 Note 6

63409 OP 100 User Manual 1

63322 Ortho Trans User Manual 1 Note 7

63328 User Program Manual for s.v. 1.2.07 and 1.2.14 1

63364 OP 100 Installation Manual (S/n 71000->) 1

63321 Ortho Trans Installation Manual 1

63361 OP 100 Service Manual For Software Versions 1

63424 OP 100 Service Manual, Wiring Diagrams 1

63348 OP 100 Troubleshooting Manual 1

63345 Maintenance Manual 1

63330 Service Program Manual 1.2.07 and 1.2.14 1

63301 Ortho ID Installation & Technical Manual 1

1516 9

172

19

1

13




63300 Ortho ID User Manual 1

63444 Replacement instructions 1

13 68301 Adjusting cross (8x10x12)in 1 Note 2

13 69982 Adjusting cross (8x10x12)in 1 Note 3

15 60424 THA alignment spike 1 Note 4

16 60441 AEC Calibration tool 1

17 68257 Ceph wedge gauge for 8x10 in 1

68398 Ceph wedge gauge 1

18 20146 Fuse 6.3 AT 10

19 60423 Ball phantom (panoramic layer) 1

20 60509 Assorted screws, washers & nuts 1

21 62978 Laser adjustment tool, for OT units 1

22 63429 Cable contact tester: CPU, X4---Fil.Cont., X38 1

Note 1: Dealer kit for USA/ Canada

Note 2: Used with new OC 100 collimator from unit s/n 70458.

Note 3: Units with s/n 70000-70457.

Note 4: Code 68257 for OC100 unit’s s/n 70000-70559, code 68398 for all units.

Note 5: Old publications.

Note 6: From S7n 72000. Service Manual 63344 replaces Technical Support Manual 69913.

Note 7: From s/n 78449 positioning ruler instruction added.


1-13 60523 Maintenance Kit B Note 3

1 65630 OP 100 Fluorescent tool (for narrow slit “JT”) 1

69915 OP 100 Fluorescent tool (“JS”) 1

2 69980 Ball & 2 pin phantom 1

15

19

16

17

9

2

1

13

9 Service tools



3 20912 Lamp 12 V/20 W 1

4 6027 Lamp 12 V /5 W 1

5 20045 Fuse 15 AT 10

6 20154 Fuse 10 AT 10

7 20204 Fuse 16 AFF 10

8 21275 Fuse 2 AT 10

9 61215 Tool kit-Incl. Allen wrenches 1.5, 2, 3, 4, 5 and 6 mm

1

10 69914 Installation Manual 1 Note 8

11 69906 User Manual 1 Note 8

12 69913 Technical Support Manual 1 Note 8

63344 Service Manual 1 Note 10

63409 OP 100 User Manual 1

63322 Ortho Trans User Manual 1

63328 User Program Manual for s.v. 1.2.07 and 1.2.14 1

63364 OP 100 Installation Manual (S/n 71000->) 1

63321 Ortho Trans Installation Manual 1 Note 11

63361 OP 100 Service Manual For Software Versions 1

63424 OP 100 Service Manual, Wiring Diagrams 1

63348 OP 100 Troubleshooting Manual 1

63345 Maintenance Manual 1

63330 Service Program Manual 1.2.07 and 1.2.14 1

63301 Ortho ID Installation & Technical Manual 1

63300 Ortho ID User Manual 1

63444 Replacement instructions 1

13 68300 Adjusting cross (18x24S, 18x24A, 24x30A) cm) 1 Note 4

13 69984 Adjusting cross (18x24, 24x30cm) 1 Note 5

15 60424 THA alignment spike 1

16 60441 AEC Calibration tool 1

17 68256 Ceph wedge gauge for 18x24 cm 1 Note 6

68398 Ceph wedge gauge 1

18 20146 Fuse 6.3 AT 10

19 60423 Ball phantom (panoramic layer) 1

21 62978 Laser adjustment tool, for OT units 1

22 63429 Cable contact tester: CPU, X4---Fil.Cont., X38 1

23 65831 OP 100 Prüfkörperadapter 1 Note 7

24 65832 OC100 Prüfkörperadapter 1 Note 7

Note 3: Dealer kit for Europe.

Note 4: Used with new OC 100 collimator from s/n 70458.

Note 5: Units with s/n 70000-70457.



Note 6: Code 68256 for OC100 unit’s s/n 70000-70599, code 68398 for all units.

Note 7: From s/n 73639 delivered with units to Germany.

Note 10: From s/n 72000. Service Manual 63344 replaces Technical Support Manual 69913.

Note 11: Manual upgraded from kit s/n 468.



German language manuals


63395 Bedienungsanleitung 1 Note 8

63430 Bedienungsanleitung 1 Note 9

63366 Montageanleitung ab s/n 71000 1

63370 Benutzerprogramm Anleitung 1.2.07 oder höher 1

63398 Serviceprogramm Anleitung 1.2.07 1

63416 Servicehandbuch VOLIII, Softwareversionen 1

63404 Servicehandbuch VOLVII, Wartung 1

63456 ServicehandbuchVOLIV,Elektrobetrieb&Verdahtung

1

63407 Servicehandbuch VOL V, Fehlerbehebung 1

63403 Ortho Trans Installationshandbuch 1

63399 Otrho Trans Bedienerhandbuch 1

63401 ORtho Zone & ORtho TMJ Bedienerhandbuch 1

63405 Ortho ID, Technisches Handbuch 1

63402 Ortho ID, Installations- & Bedienerhandbuch 1

63615 Handbuch Komponentenaustausch 1

Note 8: Old publication to s/n 73926.



9 Service tools


10 Recommended spare partsThe following Spare Part Kits A and B contain the necessary parts for servicing OP 100's in most cases.

Kit A has parts that may be needed when servicing imaging and operation related equipment problems. It isfor the major service center and for a large installed OP 100 base. Kit B is for field service centers and for asmall installed OP 100 base.

Kits A/JP and B/JP are for Japan, the only difference to Kit A is the counter weight cable (pos 1) due to theshorter column.

Universal Spare Part Minikit for every serviceman, units s/n 72000 and up with SW 1.2.07 and up.

10.1 Spare part kits


1-78 60518 Spare part Kit A 1

1 60277 Counterweight cable, std 2


3 20007 Vertical (Z) Motor M1 1

4 68954 Cable C3 1

5 60329 Trim weight 3

6 60331 Trim weight 2 3

7 60402 Counter weight Locking, complete 1

8 69961 Remote exposure, complete 1

9 60458 Adjustment plate set 1

10 60482 Carriage guide wheel ∅70 2

11 60481 Pulley∅70 assembly 2

12 60483 Guide wheel ∅ 30, assembly 2

13 68971 Cable SC1 1

14 68972 Cable SC2 1

15 68959 Cable C8 (X117) 1


17 60113 Power Supply Board 1

18 20146 Fuse 6.3 AT 10

19 21275 Fuse 2AT 10

20 68953 Cable C2 1

21 68955 Cable C4 1

22 68978 Choke oli cable L1 1


24 68956 Cable C5 1

25 68960 Cable C9 1

26 68962 Cable C11 1

27 68963 Cable C12 1

28 68964 Cable C13 1


9 Service tools


29 60123 Interface board 1 Note 1

30 68957 Cable C6 1

31 68958 Cable C7 1

32 62067 Linear Motor & Gear, complete 1

33 60108 Patient positioning panel 1

34 68961 Cable C10 1

35 61168 Mirror 2

36 20912 Lamp 12 V/ 20 W 2

37 6027 Lamp 12 V/ 5W 2

38 20045 Fuse 15 AT 10

39 20154 Fuse 10 AT 10

40 68952 Cable C1 1

41 68969 Cable set (Groundings) 1

42 61160 Control panel complete 1

43 68973 Cable SC3 (Control panel) 1

44 60509 Assorted screws, washers & nuts for OP 100 1

45 66360 Tube Head assembly, Toshiba 1

46 60115 Inverter Board 1

47 20204 Fuse 16 AFF 10

48 68965 Cable C14 1

49 68966 Cable C15 1

50 68967 Cable C16 1


52 67238 Rod for PAN/QA knob 1

53 67236 PAN/QA knob 1

54 68121 Rod for QA/PAN/CEPH knob 1

55 68122 QA/PAN/CEPH Knob 2

56 365 Screw M3x3 5

57 21279 Spring (for ceph wedge) 5

58 68968 Cable C17 1

59 60134 Head Support Lock 1

60 60136 Head support Lock Switches 1

61 63822 Rotation Motor &Gear, complete 1

62 60122 AEC Board 1

63 68974 Cable SC4 1

64 68975 Cable SC5 1

65 20905 Motor, cassette lift 1

66 65829 Cassette motor & gear assembly, complete 1

67 65580 Cephalostat lock assembly 1

68 60110 Ceph Soft Tissue Display Board 1

69 60143 Ceph up/down Switch 1

10 Recommended spare parts



70 21245 Micro switch AH 3802619 1

71 68979 Cephalostat Cable CC! 1

72 68980 Cephalostat cable CC2 1



75 68293 Magnification scale, L 2

76 68292 Magnification scale, R 2

77 68250 Installation accessory set 1


Note 1: CE-models must have code 60166 interface board OT and CPU board PAL circuit 2.0.0.


1-31 60519 Spare Part Kit B 1

1 60277 Counterweight cable, std 2





6 60481 Pulley∅ 70 assembly 2

7 60483 Guide wheel ∅ 30 assembly 2



10 20146 Fuse 6.3 AT 10

11 21275 Fuse 2AT 10


13 60123 Interface board 1 Note 1

14 62067 Linear motor & gear complete 1

15 60108 Patient Positioning Panel 1

16 61168 Mirror 1

17 20912 Lamp 12 V /20 W 1

18 6027 Lamp 12 V / 5 W 10

19 20045 Fuse 15 AT 10

20 20154 Fuse 10 AT 10

21 61160 Control Panel, complete 1




25 63822 Rotation motor & gear complete 1






28 65829 Cassette motor & gear assembly 1



31 21245 Micro switch AH 3802619 1

Note 1: CE-models must have code 60166 interface board OT and CPU board PAL circuit 2.0.0.


1-78 60520 Spare Part Kit A/JP 1

1 60327 Counterweight cable, short 2



4 68954 Cable C3 1

5 60329 Trim weight 3

6 60331 Trim weight 2 3

7 60402 Counter weight locking, complete 1

8 69961 Remote exposure, complete 1



11 60481 Pulley∅ 70 assembly 2

12 60483 Guide wheel ∅ 30 assembly 2

13 68971 Cable SC1 1

14 68972 Cable SC 2 1

15 68959 Cable C8 (X117) 1



18 20146 Fuse 6.3 AT 10

19 21275 Fuse 2 AT 10

20 68953 Cable C2 1

21 68955 Cable C4 1

22 68978 Choke oil L1 1

23 60112 CPU Board 1 See note 1

24 68956 Cable C5 1

25 68960 Cable C9 1

26 68962 Cable C11 1

27 68963 Cable C12 1

28 68964 Cable C13 1

29 60123 Interface Board 1 See note 1

30 68957 Cable C6 1

31 68958 Cable C7 1

32 62067 Linear Motor & Gear assembly 1




33 60108 Patient Positioning Panel 1

34 68961 Cable C10 1

35 61168 Mirror 2

36 20912 Lamp 12 V / 20 W 2

37 6027 Lamp 12 V / 5 W 2

38 20045 Fuse 15 AT 10

39 20154 Fuse 10 AT 10

40 68952 Cable C1 1

41 68969 Cable Set (groundings) 1

42 61160 Control panel, complete 1

43 68973 Cable SC3 (control panel) 1

44 60509 Assorted screws, washers, nuts 1

45 66360 Tube head assembly, Toshiba 1

46 60115 Inverter board 1

47 20204 Fuse 16 AFF 10

48 68965 Cable C14 1

49 68966 Cable C15 1

50 68967 Cable C16 1


52 67238 rod for PAN/QA knob 1

53 67236 PAN/QA knob 1

54 68121 Rod for QA/PAN/CEPH knob 1

55 68122 QA/PAN/CEPH knob 2

56 365 Screw M3x3 5

57 21279 Spring (for ceph wedge) 5

58 68968 Cable C17 1

59 60134 Head support lock 1


61 63822 Rotation motor & gear complete 1


63 68974 Cable SC4 1

64 68975 Cable SC5 1


66 65829 Cassette motor & gear assembly, complete 1

67 65580 Cephalolostat lock assembly 1

68 60110 Ceph soft Tissue Display Board 1


70 21245 Micro switch AH 3802619 1








75 68293 Magnification scale, L 2

76 68292 Magnification scale, R 2

77 68250 Installation accessory set, complete 1


Note 1: CE-models must have code 60166 Interface board OT and CPU board PAL circuit 2.0.0.


1-31 60521 Spare part Kit B/JP 1

1 60327 Counterweight cable, short 2




5 60482 Carriage guide wheel f 70 2

6 60481 Pulley f 70 assy 2

7 60483 Guide wheel f 30 assy 2



10 20146 Fuse 6.3 AT 10

11 21275 Fuse 2 AT 10


13 60123 Interface Board 1 Note 1

14 62067 Linear Motor & Gear, compl. 1

15 60108 Patient Positioning panel 1

16 61168 Mirror 1

17 20912 Lamp 12 V / 20 W 1

18 6027 Lamp 12 V / 5 W 1

19 20045 Fuse 15 AT 10

20 20154 Fuse 10 AT 10

21 61160 Control Panel, compl. 1




25 63822 Rotation Motor & Gear, compl. 1



28 65829 Cassette motor & gear assembly, compl. 1


30 60143 Ceph Up/down Switch 1

31 21245 Micro switch AH 3802619 1

Note 1: CE-models must have code 60166 Interface board OT and CPU board PAL circuit 2.0.0.



10.2 Spare part minikit, unit’s s/n 72000 and up.SW 1.2.07 and up.


1-19 63415 Spare Part Minikit 1



3 20146 Fuse 6.3 AT 5

4 21275 Fuse 2 AT 5

5 60112 CPU Board 1

6 60166 Interface Board OT 1

7 60108 Patient Positioning panel 1

8 20154 Fuse 10 AT 5

9 61160 Control Panel, compl. 1





14 60143 Ceph Up/down Switch 1

15 21245 Micro switch AH 3802619 1

16 65744 Secondary slot OP 100 OT, PAN 1 Note 1

17 65708 Secondary slot OP100 OT, TOMO 1

18 62094 Cable C13 + head support bracket 1 Note 1

19 20912 Lamp 12 V/ 20 W 1

Note 1: Code 65780 replaces code 65744. 65781 replaces 65708. From s/n 72191 and from kit s/n 46.

10.3 Ortho Trans spare part kits


60095 ORTHO TRANS Spare Part kit EUR. 1

66439 THA Front Cover QA/PAN/TOMO 1

68363 THA Front Cover QA/PAN/TOMO 18x24SV/24x30AV

1

68367 THA Front Cover QA/PAN/TOMO 18x24SV/1 8x24AV

1

67299 Aperture plate TOMO 1 8x24S V/1 8x24AV, left 1

67300 Aperture plate TOMO 18x24SV/18x24AV, right 1

67309 Aperture plate TOMO 1 8x24SV/24x30AV, left 1

67310 Aperture plate TOMO 1 8x24SV/24x30AV, right 1

67308 Front Al-filter 1

67307 Back Al-filter 1




67302 Primary slit plate PAN/TOMO 1

67298 Code bar 1

67314 Collimator sliding carriage OT 1

62946 Tomo bite positioner complete 1

62977 Bite plate large, 100pcs/set 1

62976 Bite plate small, 1 00pcs/set 1

65744 Secondary slot OP100 OT, PAN 1

65708 Secondary slot OP 100 OT, TOMO 1

64669 OP 100 Head support complete 1

64696 OP 100 Head support OT 1

62084 Head support bracket OT+Cable C 13 complete 1

64694 TMJ pointer OT 1

63819 Rotating unit lower cover OT 1

61261 Mirror cover OT 1

60108 Positioning panel 1

60166 Interface board OT 1

60130 User Program v.1.2.07 1

60137 Service Program v.1.2.07 1

60172 ICD 25, circuit v.2.0.0 1

63321 OP 100 OT Installation manual 1

63322 OP 100 Ortho Trans user manual 1

63328 OP100 User program manual v.1.2.07 1

63330 OP100 Service program manual v.1.2.07 1


60096 ORTHO TRANS Spare Part kit USA 1


68366 THA Front Cover QA/PAN/TOMO 8x10AV/8x10SV

1

68368 THA Front Cover QA/PAN/TOMO 8x10AH/8x10SV

1

67296 Aperture plate TOMO 8x10AV/8x10SV, left 1

67297 Aperture plate TOMO 8x10AV/8x10SV, right 1

67305 Aperture plate TOMO 10x8AH/8x10SV, left 1

67306 Aperture plate TOMO 10x8AH/8x10SV, right 1




67298 Code bar 1












62084 Head support bracket OT+Cable C1 3 complete 1








60172 ICD 25, circuit v.2.0.0 1






60097 ORTHO TRANS Spare Part kit JAP 1


68381 THA Front Cover QA/PAN/TOMO 10x12AV/8x10SV

1

67321 THA Front Cover QA/PAN/TOMO 10x12AV/8x10SV, left

1





67298 Code bar 1












62084 Head support bracket OT+Cable C1 3 complete 1








60172 ICD 25, circuit v.2.0.0 1





10.4 Screws and washers for OP100 covers


1 3202 Screw M3 x 6 lower support cover 6

1 21509 Screw M3 x 6 lower support cover 6 Note 2

2 5708 Screw M4 x 8 main support cover 2

3 21443 Screw M4 x 8 side plate cover 8

4 3588 Washer 4.3 8

5 5708 Screw M4 x 8 carriage lower trim cover 2

6 2656 Screw M4 x 8 carriage upper trim cover 2

7 3588 Washer 4.3 2




8 3230 Screw M4 x 10 carriage top plate 4

9 3588 Washer 4.3 4

10 3230 Screw M4 x 10 carriage bottom plate 2

11 3588 Washer 4.3 2

12 5708 Screw M4 x 8 carriage trim cover 2

13 21443 Screw M4 x 8 column hatch 4

14 3588 Washer 4.3 4

15 3069 Screw M4 x 12 tube head cover 6

16 5708 Screw M4 x 8 head guard 2

20023 Plastic screw M4 2

17 2754 Screw M4 x 8 cable shield 2

18 3588 Washer 4.3 2

19 365 Allen screw M3 x 3 for knob 3

20 21443 Screw M4 x 8 rotating unit lower cover 4

21 21443 Screw M4 x 8 column back plate 4

22 3588 Washer 4.3 4

23 21443 Screw M4 x 8 cephalostat cover 4

24 2656 Screw M4 x 8 for back plate 2

25 2740 Screw M4 x 6 for trim cover 6 Note 1

25 21443 Screw M4 x 8 for trim cover 6 Note 2

26 21402 Plastic plug M4 6 Note 1

27 4291 Washer 4.3 2 Note 2

Note 1 : Up to s/n 70999.



60509 Assorted screws & washers including: 1

1 3202 Screw M3x6 50

1 21509 Screw M3x6 50 Note 2

2 5708 Screw M4x8 50

3 21443 Screw M4x8 50

4 3588 Washer 4.3 50

6 2656 Screw M4x8 50

8 3230 Screw M4x10 50

15 3069 Screw M4x12 50

17 2754 Screw M4x8 50


25 2740 Screw M4x6 50 Note 1

25 21443 Screw M4x8 for trim cover 50 Note 2




26 21402 Plastic plug 50 Note 1

26 4291 Washer 4.3 50 Note 2

Note 1: Up to s/n 70999.


10.5 Colors

Touch up paints in small bottles


9224 White RAL 9002, T-M 3096-9 1 Units s/n 70000-7 1322

60587 White percotex, 449-335 From unit s/n 71323

60588 Mint green Series 260, 260-118 All units


11 Ortho Trans units & upgrade kit parts



60028 OP 100 OT Kit QA/PAN/TOMO

60090 OC100 OT Kit QA/PAN/TOMO/18x24AV/18x24SV



60093 OC100 OT Kit QA/PAN/TOMO/10x8AH/8x10SV


2 62081 Support bracket 1

62082 Extension support 1

62073 Cable clamp 2

64653 Adhesion plate 1

OP100BOT

20

20




3 68964 Cable C13 1

69020 Cable for micros hitches assembled to cable C 13in OT- Kit.

2+3 62084 Head support bracket OT+ cable C 13 Assembly 1 Note 1

62094 Head support bracket OT+ cable C 13 Assembly 1 Note 2

4 61261 Mirror cover OT 1

61344 Mirror cover OT 1 Note 6

5 62945 Bite plate, large 10

62971 Bite plate, small 10

62977 Bite plate large, 100pcs. 1

62976 Bite plate small, 100pcs. 1

6 62946 Tomo bite positioner complete 1 Note 5

7 60130 User program v. 1.2.07 1

60137 Service program v.1.2.07 1

60172 ICD25,PAL circuit, v.2.0.0 1

8 60108 Positioning panel 1

9 66439 THA Front cover QA/PAN/TOMO 1

68381 THA Front cover QA/PAN/TOMO 10x12AV/8x10SV

1

68366 THA Front cover QA/PAN/TOMO 8x10AV/8x10SV

1

68368 THA Front cover QA/PAN/TOMO 8x10AH/8x10SV

1

68363 THA Front cover QA/PAN/TOMO 18x24SV/24x30AV

1

68367 THA Front cover QA/PAN/TOMO 18x24SV/1 8x24AV

1

10 67314 Collimator sliding carriage OT 1

67299 Aperture plate TOMO 1 8x24S V/1 8x24AV, left 1


67309 Aperture plate TOMO 1 8x24SV/24x30AV, left 1


64415 Aperture plate TOMO 18x24 SV/AH, left 1

64414 Aperture plate TOMO 18x24SV/AH, right 1

67296 Aperture plate TOMO 8x10AV/8x10SV, left 1


67305 Aperture plate TOMO 10x8AH/8x10SV, left 1


67321 Aperture plate TOMO 1 0x12AV/8x1 0SV, left 1


11 67315 OP100 Collimator QA/PAN/TOMO 1




67316 OC100 Collimator QA/PAN/TOMO/18x24SV/1 8x24AV

1

67319 OC100 Collimator QA/PAN/TOMO/18x24SV/24x30AV

1


1

67318 OC 100 Collimator QA/PAN/TOMO/8x1 0SV/10x8AH

1


1

12 64669 Head support OP 100 OT, complete 1

13 63819 Rotatining unit lower cover 1

14 65708 Secondary slot OP100 OT,TOMO 1 Note 3

65803 Secondary slot OP 100 OT,TOMO 1 Note 4

15 65744 Secondary slot OP 100 OT, PAN 1 Note 3

65802 Secondary slot OP 100 OT, PAN 1 Note 4

16 65709 Secondary plate OP 100 OT, complete 1 Note 3

65779 Secondary plate OP 100 OT, complete 1 Note 4

65917 Secondary plate OP100 OT, CR units

17 60166 Interface board 1

18 69019 Laser cable, X132/X133 1

19 63745 Hair cover OT, complete 1

20 63855 Laser Projector, assembly 2

69021 Laser Projector 2

21 64703 Occlusal film holder 1 Note 7




Note 4: From s/n 72191. From s/n 73500 and kit s/n 158, “PAN” and “TOMO” recognition added tosecondary slot plates.

Note 5: From s/n 72724 Angle indicator added and fixing pins are adjustable. From s/n 73326 side adjustingrange larger and a scale to front side added.





1 2Pos Code Description Qty Note

67336 Kit 18X24SV / 18X24 AV

1 68367 THA Front cover QA/PAN/TOMO 18x24SV/1 8x24AV

1

2 67299 Aperture plate TOMO 1 8x24S V/1 8x24AV, left 1


6277 Pin 2

67337 Kit 18x24SV / 24x30AV

1 68363 THA Front cover QA/PAN/TOMO 18x24SV/24x30AV

1

2 67309 Aperture plate TOMO 1 8x24SV/24x30AV, left 1


6277 Pin 2

67338 Kit 8x10AV / 8x10SV

1 68366 THA Front cover QA/PAN/TOMO 8x10AV/8x10SV

1

2 67296 Aperture plate TOMO 8x10AV/8x10SV, left 1

67297 Aperture plate TOMO 8x10AV/8x10SV, right

6277 Pin 2

67339 Kit 10x8AH / 8x10SV

1 68368 THA Front cover QA/PAN/TOMO 8x10AH/8x10SV

1

2 67305 Aperture plate TOMO 10x8AH/8x10SV, left 1


6277 Pin 2

67340 Kit 10x12AV / 8x10SV

1 68381 THA Front cover QA/PAN/TOMO 10x12AV/8x10SV

1

2 67321 Aperture plate TOMO 1 0x12AV/8x1 0SV, left





6277 Pin 2

64415 Aperture plate TOMO 18x24 SV / 18x24AH, left 1

64414 Aperture plate TOMO 18x24 SV / 18x24AH, right 1

6277 Pin 2

64419 THA front cover QA/PAN/TOMO/18x24 AH/18x24 SV

1



12 Fan Kit


12 Fan Kit


61352 Fan Kit Note 1

1 5938 Screw M4x35, DIN 7985 1

542 Washer 4,3A, DIN 1

2 63860 Fan bracket 1

3 61358 Fan 1

4 61135 Cover 1

5 61351 Hairguide 1

6 61353 Fan 1

7 325 Nut M4, DIN 934 3


9 61350 Fixing plate 1

10 5938 Screw M4x35, DIN 7985 2

11 22623 Screw 3,5x9,5 2

12 62051 main Support Cover 1

13 61354 Cable, Interface 1

14 61355 Cable, Inverter 1

61352-4C Installation Instructions 1

8

7

910

11

6

5

12

13

4

14

21

3

12 Fan Kit


Note 1: From s/n 75163

12.1 Boxes


60747 Cardboard column box 1 Note

Note: OP/OC100 from s/n 80747.

Instrumentarium Imaging

P.O.Box 20, FIN-04301 Tuusula, Finland

Tel. +358 10 394 6500 · Fax +358 10 394 6501

[email protected]

Instrumentarium Imaging Inc.

300 West Edgerton Avenue, Milwaukee

Wisconsin 53207, USA

Tel. +1 800 558 6120, +1 414 747 1030

F a x + 1 4 1 4 4 8 1 8 6 6 5

[email protected]

Instrumentarium Imaging France S.A.R.L.

4, Avenue des Roses

94386 Bonneuil Sur Marne Cedex, France

Tel. +33 1 43 39 51 51 · Fax +33 1 43 39 75 75

[email protected]

Instrumentarium Imaging Italia S.R.L.

Via Cassanese, 100

20090 Segrate (MI), Italy

Tel. +39 02 21 30 28 1 · Fax +39 02 21 30 28 60

instrumentarium@it. instrumentarium.com

Instrumentarium Imaging Singapore

152 Beach Road

#12-03A Gateway East

189721 Singapore

Tel. +65 6391 8600 · Fax +65 6396 3009

[email protected]

Instrumentarium Imaging Dental GmbH

P.O.Box 2044, 77680 Kehl am Rhein, Germany

Tel. +49 7851 932 90 · Fax +49 7851 932 930

[email protected]

Instrumentarium Imaging is constantly improving its products and reserves the right tochange these specifications without notice.

www.InstrumentariumImaging.com

Distributor:

Documents

69977 OP100 OC100 Spare Parts Manual 4AE