Upload
gary-gorski
View
220
Download
0
Embed Size (px)
Citation preview
8/6/2019 8865 Instructions - Panasonic 2011 3D & VC Display Resets - 6th Avenue Electronics High Resolution[1]
http://slidepdf.com/reader/full/8865-instructions-panasonic-2011-3d-vc-display-resets-6th-avenue-electronics 1/17
1
Program Name: Panasonic 2011 3D and VIERA Connect (VC) Display Resets - 6th Avenue Electronics
Project Codes: 8865 Visit Dates: (05/09/11 - 05/12/11) Rep Support Hotline: 877-484-0232
CHECKLIST TO ENSURE A SUCCESSFUL VISIT
PLEASE READ: This checklist provides an OVERVIEW of the major tasks you need to accomplish to successfully complete this project. However, you still need to read and carefully follow the detailed instructions on the following pages. The detailsare VERY IMPORTANT to ensure success too. Do NOT assume you know how to complete the project using only this checklist.
BEFORE YOU VISIT THE STORE:
IMPORTANT: Complete a pre-call to the store - see pre-call instructions on page 3.
Prepare the materials (graphics, TV mounting screw kit) that shipped directly to your home.
Gather the tools you will need during your visit.
Print your instructions, survey, and leave behind documents.
Ensure your camera is charged and ready to take photos.
DURING YOUR VISIT:
Sign in and review your objectives.
Locate the Panasonic 3D Display and the VIERA Connect (formerly VIERA Cast) Display ( two separate displays).
Remove the old 2010 TV and Home Theater models from BOTH displays. SAVE the existing demo discs.
Install the following 2011 Panasonic models on the 3D Display using the TV mounting screw kit provided:
TC-P55VT30 3D TV
SC-BTT370 3D Blu-ray Home Theater
Install the following 2011 Panasonic models on the VIERA Connect Display using the TV mounting screw kit:
TC-P50GT30 TV
SC-BTT270 Blu-ray Home Theater
Turn units on and set TVs to Store Demonstration mode.
Install ALL of the new graphics on the 3D Display, 3D Pedestal, and VIERA Connect Display. MAKE SURE YOUPAY CLOSE ATTENTION TO THE CONSOLE GRAPHICS - they are model specific and you MUST install the correct one!!
Reinstall the existing demo disc on the 3D Display and install the NEW disc on the VIERA Connect Display.
Ensure all wires and cables are managed well and concealed OUT OF SIGHT inside the display or wire track.
Ensure all models are fully functional and playing the provided demo content.
Complete a THOROUGH audit of the 3D Eyewear Pedestal. If not functioning, try to make it functional.
Thoroughly check BOTH displays and report any missing parts or needed items on your survey.
Take at least one photo of EACH display showing the work you completed.
AFTER YOUR VISIT:
Login to Natural Insight and complete your survey on the same day that you completed the project.
Carefully and accurately answer all questions, and submit the photos you took at the store.
Project Checklist
8/6/2019 8865 Instructions - Panasonic 2011 3D & VC Display Resets - 6th Avenue Electronics High Resolution[1]
http://slidepdf.com/reader/full/8865-instructions-panasonic-2011-3d-vc-display-resets-6th-avenue-electronics 2/17
2
Program Name: Panasonic 2011 3D and VIERA Connect (VC) Display Resets - 6th Avenue Electronics
Project Codes: 8865 Visit Dates: (05/09/11 - 05/12/11) Rep Support Hotline: 877-484-0232
CHECKLIST AND PHOTOS OF MATERIALS NEEDED TO COMPLETE PROJECT
PLEASE READ: Carefully review the descriptions and photos of the materials indicated below. You NEED these materials to suc-cessfully complete this project! If the materials delivered to your home, please make sure you have the materials BEFORE you visit
the store. If you do not have the materials that should have delivered to your home, please contact your Regional Manager or theRep Support Hotline for assistance. Remember that tracking information is posted to Natural Insight. Make sure you track the ship-
ments before calling for assistance.
MATERIALS NEEDED:
You need THREE total kits for each store to complete this project.
(1) Regional 3D Graphics Reset Kit sent directly to you from a third party.
(1) Regional VIERA Connect (VC) Graphics Reset Kit sent directly to you from a third party.
(1) TV Mounting Screw Kit sent directly to you from a third party. NOTE: this kit may have shipped inside one of thegraphics kits.
Do NOT visit your store until you have received the materials needed to complete this project!
Carefully check all packing material for the kit contents. Inspect each piece for damage. Report missing/damaged pieces to the RepSupport Hotline immediately.
Materials Needed
3D KIT CONTENTS:
(1) Header Topper Graphic
(1) VT Series Console Graphic
(1) GT Series Console Graphic
(2) Front/Back Pedestal Graphics
(1) Top Pedestal Graphic
VIERA CONNECT (VC) KIT CONTENTS:
(1) GT Series Console Graphic
(1) GT30 Video Demo Disc
(1) ST Series Console Graphic
(1) ST30 Video Demo Disc
TV MOUNTING SCREW KIT CON-TENTS (NOT pictured):
Screws of various sizes to mount the 3Dand VC TVs
8/6/2019 8865 Instructions - Panasonic 2011 3D & VC Display Resets - 6th Avenue Electronics High Resolution[1]
http://slidepdf.com/reader/full/8865-instructions-panasonic-2011-3d-vc-display-resets-6th-avenue-electronics 3/17
3
Program Name: Panasonic 2011 3D and VIERA Connect (VC) Display Resets - 6th Avenue Electronics
Project Codes: 8865 Visit Dates: (05/09/11 - 05/12/11) Rep Support Hotline: 877-484-0232
PLEASE NOTE: The Interactive Media Boxes originally part of this project did not ship - you will NOT need to install a media box.Since the media box did not ship, you need to KEEP and REINSTALL the existing 3D DEMO DISC that you find in the 3D DISPLAY. Anew 3D Demo Disc DID NOT SHIP in the materials kits, you MUST REUSE the existing 3D Disc.
PROJECT TIME: This project will take an estimated 210 minutes in-store plus 15 minutes of admin time, and pays a printing reimbursement.
BEFORE YOU VISIT THE STORE:
□ PRE-CALL
You MUST call the store to schedule your visit and confirm the items below. Complete the following pre-call objectives:
Confirm the existing 3D and VIERA Connect (formerly VIERA Cast) Panasonic Displays are still present. If one or both of the displays are no longer present, do not visit the store - call the Rep Support Hotline.
Confirm that the models needed for BOTH displays are in stock. If the models are not available, DO NOT VISIT THESTORE. Report the situation IMMEDIATELY to the Rep Support Hotline.
Schedule an appointment for your visit. Make sure you keep your appointment; if you must reschedule, keep the storeinformed. Also, keep your visit schedule updated in NI.
□ MATERIALS
Gather the materials needed for your visit (see previous page). If you have a materials issue or question, please contact the RepSupport Hotline immediately.
□ TOOLS
Gather the tools listed below and take them with you to the store.
□ PRINT DOCUMENTS Print your instructions, survey, and leave behind documents from Natural Insight (NI). YouNEED them to ensure success during your visit.
□ CAMERA Ensure your camera is charged and ready to take photos. Photos are REQUIRED for this project.
Project Instructions
Medium- and large-sized Phillips and Flat head screwdrivers
Tape Measure
Tin snips/scissors
Pliers or crescent wrench
Allen key assortment
Cleaning cloth
Instructions may have shipped with the kits. Use those instructions for reference only as necessary. Follow these instructions instead.
8/6/2019 8865 Instructions - Panasonic 2011 3D & VC Display Resets - 6th Avenue Electronics High Resolution[1]
http://slidepdf.com/reader/full/8865-instructions-panasonic-2011-3d-vc-display-resets-6th-avenue-electronics 4/17
4
Program Name: Panasonic 2011 3D and VIERA Connect (VC) Display Resets - 6th Avenue Electronics
Project Codes: 8865 Visit Dates: (05/09/11 - 05/12/11) Rep Support Hotline: 877-484-0232
OVERVIEW OF IN-STORE OBJECTIVES: The main goal of this project is to reset the Panasonic 3D Display and the VIERA Connect(VC) Display with the new 2011 TV and Blu-ray Home Theater (HT) models, and to install new graphics and VC demo disc. You need to ensureboth displays are fully functioning and set perfectly, with all wires concealed. Complete the following objectives to successfully finish this project:
1. Sign into the vendor log and review your objectives with the Store or Electronics Manager.
2. Locate the Panasonic 3D Display and the Panasonic VIERA Connect (formerly VIERA Cast) Displays currently setup in the store.
3. Remove the old 2010 models from BOTH the 3D and VC Displays. Work with the store to re-display or put away the models as requested.
4. 3D DISPLAY ONLY: Install the TC-P55VT30 3D TV & SC-BTT370 3D Blu-ray HT on the 3D DISPLAY.
5. VIERA CONNECT DISPLAY ONLY: Install the TC-P50GT30 TV & SC-BTT270 Blu-ray HT on the VIERA CONNECT DISPLAY.
6. BOTH DISPLAYS: Turn units on and set TVs to Store Mode.
7. 3D DISPLAY: Install on the 3D Display the new 3D graphics that shipped directly to you. REINSTALL the existing 3D Demo Disc.
8. VC DISPLAY: Install on the VIERA Connect Display the new VC graphics and new demo disc that shipped directly to you.
9. BOTH DISPLAYS: Ensure both displays are fully functioning and look perfect with ALL WIRES concealed. Ensure 3D Pedestal is functional.
10.TAKE AND SUBMIT PICTURES of BOTH displays, and review your work with the store manager.
Objective #1: Sign in and Review Objectives
Sign into the vendor log.
Review your objectives with the Store or Electronics Manager.
Explain the purpose of your visit as described above.
If you cannot complete your objectives FOR ANY REASON, make sure you obtain a manager sign-off and fax the first page of your survey to the number shown on your survey.
Objective #2: Locate the Panasonic Displays
The stores should have the Panasonic 3D and VIERA Connect Displays already setup on the sales floor.
The EXISTING 2010 Panasonic 3D and VIERA Connect Displays should look similar to the pictures below upon entry.
EXISTING 3D Display with 2010 Models,
Old Graphics, and Demo Disc
EXISTING VIERA Connect Display with
2010 Models, Graphics, Demo Disc
8/6/2019 8865 Instructions - Panasonic 2011 3D & VC Display Resets - 6th Avenue Electronics High Resolution[1]
http://slidepdf.com/reader/full/8865-instructions-panasonic-2011-3d-vc-display-resets-6th-avenue-electronics 5/17
5
Program Name: Panasonic 2011 3D and VIERA Connect (VC) Display Resets - 6th Avenue Electronics
Project Codes: 8865 Visit Dates: (05/09/11 - 05/12/11) Rep Support Hotline: 877-484-0232
Objective #3: Remove 2010 Models (Re-Display as Requested) from 3D and VIERA Connect Displays
COMPLETE THIS OBJECTIVE FOR BOTH THE 3D AND VIERA CONNECT DISPLAYS. The instructions are THE SAME for each display.
STEP 1: Remove the TV
Turn off the TV and Home Theater models.
Unscrew four (4) screws & remove the Access Panel underneath the shelf on the display, to give you access to the power strip.
Turn off the power strip, and unplug the TV.
Disconnect the HDMI cable from the TV. Leave the HDMI cable hanging from the display, you will need to reuse it.
Loosen (but do not remove) the two (2) cap screws at the top of the TV brackets. This will allow you to remove the TV.
With an associate’s help, lift the existing TV off the display. Take great care to avoid damaging the TV.
If an associate is not available right away, begin removing the HT System - you don’t need help to do that.
UNSCREW AND REMOVE THE BRACKETS from the back of the existing TV. SAVE THE BRACKETS to use when hanging thenew TV.
Work with the store to re-display or put away the removed TV. The store should have the TV stand, if they want to place it inline.
STEP 2: Remove the Home Theater (HT)
Unplug the Home Theater (HT) from the power strip.
Unplug the HDMI cable from the back of the HT. Leave the cable fed through the display, you will need to reuse it.
Disconnect the speaker wires from the speakers, and carefully pull all speaker wires out of the display.
Lift off and remove all five speakers from their mounts. Leave the screw mounts in place.
Also remove the subwoofer and the main unit of the HT.
Work with the store to re-display or put away the removed HT.
Two Cap Screws Remove Two BracketsAccess Panel BELOW SHELF
8/6/2019 8865 Instructions - Panasonic 2011 3D & VC Display Resets - 6th Avenue Electronics High Resolution[1]
http://slidepdf.com/reader/full/8865-instructions-panasonic-2011-3d-vc-display-resets-6th-avenue-electronics 6/17
6
Program Name: Panasonic 2011 3D and VIERA Connect (VC) Display Resets - 6th Avenue Electronics
Project Codes: 8865 Visit Dates: (05/09/11 - 05/12/11) Rep Support Hotline: 877-484-0232
Objective #4: Install on 3D DISPLAY - TC-P55VT30 3D TV and SC-BTT370 3D Blu-ray Home Theater
STEP 1: Attach TV Brackets
Use brackets removed from old TV & new screws shipped to you.
The brackets should be 24” long with the extenders attached. If the extenders are NOT attached, ask the store if they know
where the extenders are - you will need them to achieve the proper height of the TV on the display. If the extenders are missingor damaged, hang the TV using the brackets that you have, but NOTE IN YOUR SURVEY the need for new extender brackets.
Uncover the screw holes on the back of the TV by removing the four plastic covers.
EXTREMELY IMPORTANT: The screws used to hang the 2010 3D TV are TOO LONG for the 2011 55VT30 TV. Use the NEWSCREWS to hang the TV.
Screw both brackets into the TV. Make sure the bracket lip is toward the top. Use the BOTTOM HOLE on the TV brackets, andthen whatever upper hole that lines up to achieve the proper TV height on the display.
STEP 2: Hang TV Ask an associate for assistance in hanging the TV on the display. Make sure the TV is CENTERED on the display!
Feed the TV power cord into the wire hole on the back wall of the display. This will conceal the cable and allow you to plug it intothe power strip inside the Access Panel. Remove the wire hole cover if necessary.
Screw in the two cap screws on the bracket lips to secure the TV in place.
After hanging TV, check to make sure the “Panasonic VIERA” text is fully visible above the TV. If not, remove the TV and installthe brackets properly as instructed above, unless the extenders are missing. The “Panasonic VIERA” text MUST BE VISIBLE.
Insert the HDMI cable into HDMI 1 on the back of the TV.
Insert the USB Extension Cable from the 3D Pedestal into USB 1 on the back of the TV. You may need to remove a sticker touncover the USB 1 input.
Ensure the HDMI , USB, and power cables are tucked up behind the TV out of sight, and fed into the wire hole on the back wall of the display, behind the TV. WIRE MANAGEMENT IS VERY IMPORTANT.
TV Centered, Panasonic VIERA visible
Four plastic covers
HDMI 1 Input
Left Bracket Properly Installed
Lip
BOTTOM HOLE
USB 1 Input
IMPORTANT: Give ALL unused TV parts to the store, especially the WirelessLAN adapter. Tell the store they need to SAVE it for when they SELL the TV.
8/6/2019 8865 Instructions - Panasonic 2011 3D & VC Display Resets - 6th Avenue Electronics High Resolution[1]
http://slidepdf.com/reader/full/8865-instructions-panasonic-2011-3d-vc-display-resets-6th-avenue-electronics 7/17
7
Program Name: Panasonic 2011 3D and VIERA Connect (VC) Display Resets - 6th Avenue Electronics
Project Codes: 8865 Visit Dates: (05/09/11 - 05/12/11) Rep Support Hotline: 877-484-0232
Objective #4 CONTINUED: Install on 3D DISPLAY - TC-P55VT30 3D TV and SC-BTT370 3D Blu-ray Home Theater
STEP 3: Install the SC-BTT370 3D Blu-ray Home Theater
READ—IMPORTANT: Proper wire management, cable connections, and speaker placement are all CRITICAL during this step. Place the Main Unit of the Blu-ray Home Theater on the shelf.
Place the Subwoofer on the display base behind Panasonic sign. Feed subwoofer wire into small wire hole under Access Panel.
All of the speakers are labeled on the back. Place the speakers as follows (LAYOUT FOR BTT370 DIFFERENT FROM BTT270):
Assemble the two tall FRONT Speakers and place them on the BASE OF THE DISPLAY.
Hang two SURROUND Speakers on the TOP speaker brackets on the sides of the display. Bottom brackets will be empty.
Hang the CENTER Speaker on the bracket behind the console graphic panel. You may need to swap screws to hang it.
IMPORTANT: Feed ALL speaker wire through the wire management holes to the INSIDE of the display so that it is concealed.
Connect the speaker wire to the Main Unit and to the Speakers according to color. The colors are labeled on the back of the Main
Unit. See below. Purple = Subwoofer
Green = Center Speaker
Red = Front RIGHT Speaker
White = Front LEFT Speaker
Gray = Surround RIGHT Speaker
Blue = Surround LEFT Speaker
Attach the speaker cable stickers according to color and number to aid in the connection process.
IMPORTANT: When connecting the speaker wire to the speakers, insert the wire with the BLUE LINE into the BLUE speaker port(-), and the WHITE WIRE into the WHITE speaker port (+).
Side Speaker Brackets Center Speaker Bracket
Blue line into BLUE,white wire into WHITE Feed wires INSIDE the wire holes
Excess wire INSIDE Ac-cess Panel
Feed ALL WIRE up through display and backout wire hole to connect to Main Unit
Speaker Labels
8/6/2019 8865 Instructions - Panasonic 2011 3D & VC Display Resets - 6th Avenue Electronics High Resolution[1]
http://slidepdf.com/reader/full/8865-instructions-panasonic-2011-3d-vc-display-resets-6th-avenue-electronics 8/17
8
Program Name: Panasonic 2011 3D and VIERA Connect (VC) Display Resets - 6th Avenue Electronics
Project Codes: 8865 Visit Dates: (05/09/11 - 05/12/11) Rep Support Hotline: 877-484-0232
Objective #4 CONTINUED: Install on 3D DISPLAY - TC-P55VT30 3D TV and SC-BTT370 3D Blu-ray Home Theater
STEP 3 CONTINUED: Install the SC-BTT370 Blu-ray Home Theater
READ—IMPORTANT: Proper wire management, cable connections, and speaker placement are all CRITICAL during this step. Insert the free end of the HDMI Cable into the HDMI Output on the back of the Main Unit.
Insert the Blu-ray HT power cord into the back of the Main Unit.
IMPORTANT WIRE MANAGEMENT: Make sure the power cable AND the HDMI cable are fed through the wire holes and con-cealed inside the display. The other end of the HDMI goes up to the TV, and the power cord goes down to the power strip insidethe Access Panel.
FRONT Speaker Wire Management: With the FRONT speakers sitting on the display base, feed the FRONT speaker wire intothe small wire hole underneath the Access Panel, and then up through the display and back out for connection to the Main unit.
Center Speaker Wire Management: Feed the center speaker wire underneath the bracket and then back toward the wire hole asshown below. Push ALL EXCESS wire into the wire hole to conceal it, after making the connection to the Main Unit.
WHEN FINISHED, your display and wire management should look CLEAN AND NEAT.
ALSO, make sure ALL of the WIRE COVERS are replaced to conceal the wire holes.
Power Cord Input Speaker Terminals HDMI OUT
GOOD WIRE MANAGEMENT - All wires fed through wire
hole; all wire hole covers placed
GOOD WIRE MANAGEMENT - No wires hanging all over the
display
8/6/2019 8865 Instructions - Panasonic 2011 3D & VC Display Resets - 6th Avenue Electronics High Resolution[1]
http://slidepdf.com/reader/full/8865-instructions-panasonic-2011-3d-vc-display-resets-6th-avenue-electronics 9/17
9
Program Name: Panasonic 2011 3D and VIERA Connect (VC) Display Resets - 6th Avenue Electronics
Project Codes: 8865 Visit Dates: (05/09/11 - 05/12/11) Rep Support Hotline: 877-484-0232
Objective #5: Install on VIERA CONNECT (VC) DISPLAY - TC-P50GT30 TV and SC-BTT270 Blu-ray Home Theater
NOTE: The TV and HT for the VC Display are DIFFERENT than the models installed on the 3D Display. Make sure you install the correctmodels on the correct displays! The VC Display should have the GT30 TV and the BTT270 HT. Use new screws provided in TV Mounting Kit.
STEP 1: Attach TV Brackets
Use the brackets and screws you removed from the old TV.
The brackets should be 24” long with the extenders attached. If the extenders are NOT attached, ask the store if they knowwhere the extenders are - you will need them to achieve the proper height of the TV on the display. If the extenders are missingor damaged, hang the TV using the brackets that you have, but NOTE IN YOUR SURVEY the need for new extender brackets.
Uncover the screw holes on the back of the TV by removing the four plastic covers.
Screw both brackets into the TV. Make sure the bracket lip is toward the top. Use the 2nd HOLE UP FROM THE BOTTOM andthe 11th HOLE DOWN FROM THE TOP to achieve the proper TV height on the display.
STEP 2: Hang TV
Ask an associate for assistance in hanging the TV on the display. Make sure the TV is CENTERED on the display!
Feed the TV power cord into the wire hole on the back wall of the display. This will conceal the cable and allow you to plug it intothe power strip inside the Access Panel. Remove the wire hole cover if necessary.
Screw in the two cap screws on the bracket lips to secure the TV in place.
After hanging TV, check to make sure the “Panasonic VIERA” text is fully visible above the TV. If not, remove the TV and installthe brackets properly as instructed above, unless the extenders are missing. The “Panasonic VIERA” text MUST BE VISIBLE.
Insert the HDMI cable into HDMI 1 on the back of the TV.
Ensure the HDMI , USB, and power cables are tucked up behind the TV out of sight, and fed into the wire hole on the back wall of the display, behind the TV. WIRE MANAGEMENT IS VERY IMPORTANT.
TV Centered, Panasonic VIERA visible HDMI 1 Input
Four plastic covers Left Bracket Properly Installed
Lip
2nd Hole Up
11th Hole Down
IMPORTANT: Give ALL unused TV partsto the store, especially
the Wireless LANadapters. Tell the store
they need to SAVEthem for when they
SELL the TVs.
8/6/2019 8865 Instructions - Panasonic 2011 3D & VC Display Resets - 6th Avenue Electronics High Resolution[1]
http://slidepdf.com/reader/full/8865-instructions-panasonic-2011-3d-vc-display-resets-6th-avenue-electronics 10/17
10
Program Name: Panasonic 2011 3D and VIERA Connect (VC) Display Resets - 6th Avenue Electronics
Project Codes: 8865 Visit Dates: (05/09/11 - 05/12/11) Rep Support Hotline: 877-484-0232
Objective #5 CONTINUED: Install on VIERA CONNECT DISPLAY - TC-P50GT30 TV and SC-BTT270 Blu-ray Home Theater
STEP 3: Install the SC-BTT270 Blu-ray Home Theater
READ—IMPORTANT: Proper wire management, cable connections, and speaker placement are all CRITICAL during this step.
Place the Main Unit of the Blu-ray Home Theater on the shelf.
Place the Subwoofer on the display base behind Panasonic sign. Feed subwoofer wire into small wire hole under Access Panel.
All of the speakers are labeled on the back. Place the speakers as follows:
Hang the two FRONT Speakers on the TOP speaker brackets on the sides of the display.
Hang the two SURROUND Speakers on the BOTTOM speaker brackets on the sides of the display.
Hang the CENTER Speaker on the bracket behind the console graphic panel. You may need to swap screws to hang it.
IMPORTANT: Feed ALL speaker wire through the wire management holes to the INSIDE of the display so that it is concealed.
Connect the speaker wire to the Main Unit and to the Speakers according to color. The colors are labeled on the back of the Main
Unit. See below. Purple = Subwoofer
Green = Center Speaker
Red = Front RIGHT Speaker
White = Front LEFT Speaker
Gray = Surround RIGHT Speaker
Blue = Surround LEFT Speaker
Attach the speaker cable stickers according to color and number to aid in the connection process.
IMPORTANT: When connecting the speaker wire to the speakers, insert the wire with the BLUE LINE into the BLUE speaker port(-), and the WHITE WIRE into the WHITE speaker port (+).
Side Speaker Brackets Center Speaker Bracket
Blue line into BLUE,white wire into WHITE Feed wires INSIDE the wire holes
Excess wire INSIDE Ac-cess Panel
Feed ALL WIRE up through display and backout wire hole to connect to Main Unit
Speaker Labels
8/6/2019 8865 Instructions - Panasonic 2011 3D & VC Display Resets - 6th Avenue Electronics High Resolution[1]
http://slidepdf.com/reader/full/8865-instructions-panasonic-2011-3d-vc-display-resets-6th-avenue-electronics 11/17
11
Program Name: Panasonic 2011 3D and VIERA Connect (VC) Display Resets - 6th Avenue Electronics
Project Codes: 8865 Visit Dates: (05/09/11 - 05/12/11) Rep Support Hotline: 877-484-0232
Objective #5 CONTINUED: Install on VIERA CONNECT DISPLAY - TC-P50GT30 TV and SC-BTT270 Blu-ray Home Theater
STEP 3 CONTINUED: Install the SC-BTT270 Blu-ray Home Theater
READ—IMPORTANT: Proper wire management, cable connections, and speaker placement are all CRITICAL during this step. Insert the free end of the HDMI Cable into the HDMI Output on the back of the Main Unit.
Insert the Blu-ray HT power cord into the back of the Main Unit.
IMPORTANT WIRE MANAGEMENT: Make sure the power cable AND the HDMI cable are fed through the wire holes and con-cealed inside the display. The other end of the HDMI goes up to the TV, and the power cord goes down to the power strip insidethe Access Panel.
Center Speaker Wire Management: Feed the center speaker wire underneath the bracket and then back toward the wire hole asshown below. Push ALL EXCESS wire into the wire hole to conceal it, after making the connection to the Main Unit.
WHEN FINISHED, your display and wire management should look CLEAN AND NEAT.
ALSO, make sure ALL of the WIRE COVERS are replaced to conceal the wire holes.
Power Cord Input Speaker Terminals HDMI OUT
GOOD WIRE MANAGEMENT - All wires fed through wire
hole; all wire hole covers placed
GOOD WIRE MANAGEMENT - No wires hanging all over the
display
8/6/2019 8865 Instructions - Panasonic 2011 3D & VC Display Resets - 6th Avenue Electronics High Resolution[1]
http://slidepdf.com/reader/full/8865-instructions-panasonic-2011-3d-vc-display-resets-6th-avenue-electronics 12/17
12
Program Name: Panasonic 2011 3D and VIERA Connect (VC) Display Resets - 6th Avenue Electronics
Project Codes: 8865 Visit Dates: (05/09/11 - 05/12/11) Rep Support Hotline: 877-484-0232
Objective #6: Turn Units On, Set TV to Store Mode
COMPLETE THIS OBJECTIVE FOR BOTH THE 3D AND VIERA CONNECT DISPLAYS. The instructions are the SAME for each display.
STEP 1: Turn TV and Home Theater On
It is very important that the power cords are concealed and connected to the power strip INSIDE the Access Panel at the base of the display.
Plug both units into the power strip, then turn on the power strip.
Turn on the 3D TV and the 3D Blu-ray Home Theater.
STEP 2: Set TV to Store Mode
When first turned on, the TV will proceed through its First Time Setup menus. Select the settings highlighted below to set the TVto store Mode.
If the TV is already displayed upon entry, access the First Time Setup menu as follows:
Press “Menu” and scroll down to the “Setup” menu (the wrench icon)
Select “Setup,” then scroll down to the second page of items Select “First Time Setup”
Then proceed according to the photos shown below.
1. Select English
2. Select U.S.A.
3. Select Store Demonstration
4. Confirm Store Demonstration Mode
5. Set Picture Refresh
and Demo Mode to
“ON,” and Interval
(min) to “5”
8/6/2019 8865 Instructions - Panasonic 2011 3D & VC Display Resets - 6th Avenue Electronics High Resolution[1]
http://slidepdf.com/reader/full/8865-instructions-panasonic-2011-3d-vc-display-resets-6th-avenue-electronics 13/17
13
Program Name: Panasonic 2011 3D and VIERA Connect (VC) Display Resets - 6th Avenue Electronics
Project Codes: 8865 Visit Dates: (05/09/11 - 05/12/11) Rep Support Hotline: 877-484-0232
Objective #7: Install on 3D DISPLAY - New 3D Graphics, Pedestal Graphics, and EXISTING Demo Disc
NOTE: The graphic placement instructions are DIFFERENT for each display - please pay close attention.
FOR THE 3D DISPLAY
STEP 1: Install the New 3D Console Graphic
CRITICAL: TWO 3D Console Graphics shipped in the kit. USE THE ONE THAT MATCHES THE TV ON THE 3D DISPLAY,i.e. the VT Graphic. Give the other one to the store.
Unscrew the four (4) allen screws holding the old console graphic and clear acrylic cover in place. Use a 1/8” Allen Key.
SAVE the (4) allen screws and the cover. Discard the old graphic.
Place the NEW VT Series Console Graphic on the display and fit the clear acrylic cover on top of the graphic.
Reattach the (4) allen screws to secure the graphic and cover.
Work with the store to print and place new fact tags for the models.
IF YOU CANNOT INSTALL THE NEW CONSOLE GRAPHIC, leave it with the store manager.
STEP 2: Install the New 3D Header Topper Graphic
Remove all existing Topper Graphics by unscrewing the (2) existing screws at the top back of the display. Save the screws.
Remove the backer from the tape strip to expose the adhesive on the new Topper Graphic.
Attach the new Header Topper Graphic using the (2) previously removed screws. Ensure the tape adheres to the display.
IF YOU CANNOT INSTALL THE NEW TOPPER GRAPHIC, leave it with thestore manager.
New Header Topper Graphic
Remove (2) Screws
Remove (4) Allen Screws New Graphic
TV Model Indicated HERE - Install Graphic that matches TV on 3D Display - i.e. VT Series
8/6/2019 8865 Instructions - Panasonic 2011 3D & VC Display Resets - 6th Avenue Electronics High Resolution[1]
http://slidepdf.com/reader/full/8865-instructions-panasonic-2011-3d-vc-display-resets-6th-avenue-electronics 14/17
14
Program Name: Panasonic 2011 3D and VIERA Connect (VC) Display Resets - 6th Avenue Electronics
Project Codes: 8865 Visit Dates: (05/09/11 - 05/12/11) Rep Support Hotline: 877-484-0232
Objective #7 CONTINUED: Install on 3D DISPLAY - New 3D Graphics, Pedestal Graphics, and EXISTING Demo Disc
FOR THE 3D DISPLAY (CONTINUED)
STEP 3: Install New 3D Pedestal Graphics
Slide the existing TOP Pedestal graphic out of the channel strip and slide the NEW TOP Pedestal graphic into the channels.
Attach the new FRONT and BACK pedestal graphics by carefully flexing the graphics into the channels provided. NOTE: You doNOT need to remove any existing front or back graphics - simply place the new graphics on top of the old graphics.
IF YOU CANNOT INSTALL THE NEW PEDESTAL GRAPHICS, leave them with the store manager.
STEP 4: Install the EXISTING 3D Demo Disc
INSTALL DEMO DISC FOUND IN 3D DISPLAY UPON ARRIVAL
Open the disc tray on the Blu-ray Home Theater and install the disc.
If the tray is locked, see below for instructions on how to unlock thetray.
Press “Input” on the TV remote, and then select “HDMI 1.”
Ensure the disc plays a clear 3D HD picture on the TV, and thatsound is coming out of the speakers.
IF YOU CANNOT INSTALL THE NEW DISC, leave it with thestore manager.
STEP 5: Lock/Unlock the Disc Tray
With the disc playing, press and hold the “PLAY” button and the “OPEN/CLOSE” button on the Main Unit.
Hold for approximately 5 seconds.
The LED will read “LOCKED.”
Repeat the same sequence to UNLOCK the tray.
Make sure you PRINT and LEAVE the Tray Lock Leave Behind document with the store so they know the process too!
Select HDMI 1 Input
TOP Graphic
FRONT and BACK Pedestal
Graphics (QTY 2)
8/6/2019 8865 Instructions - Panasonic 2011 3D & VC Display Resets - 6th Avenue Electronics High Resolution[1]
http://slidepdf.com/reader/full/8865-instructions-panasonic-2011-3d-vc-display-resets-6th-avenue-electronics 15/17
15
Program Name: Panasonic 2011 3D and VIERA Connect (VC) Display Resets - 6th Avenue Electronics
Project Codes: 8865 Visit Dates: (05/09/11 - 05/12/11) Rep Support Hotline: 877-484-0232
Objective #8: Install on VIERA CONNECT DISPLAY - New Graphic and NEW Demo Disc
FOR THE VIERA CONNECT DISPLAY
STEP 1: Install the New VIERA CONNECT Console Graphic
CRITICAL: TWO VIERA CONNECT Console Graphics shipped in the kit. USE THE ONE THAT MATCHES THE TV ONTHE VC DISPLAY, i.e. the GT Series Graphic. Give the other one to the store.
Unscrew the four (4) allen screws holding the old console graphic and clear acrylic cover in place. Use a 1/8” Allen Key.
SAVE the (4) allen screws and the cover. Discard the old graphic.
Place the NEW GT Series Console Graphic on the display and fit the clear acrylic cover on top of the graphic.
Reattach the (4) allen screws to secure the graphic and cover.
Work with the store to print and place new fact tags for the models.
IF YOU CANNOT INSTALL THE NEW CONSOLE GRAPHIC, leave it with the store manager.
STEP 2: Install the New VIERA CONNECT Demo Disc
CRITICAL: TWO demo discs shipped in the VC Kit. USE THE ONE
THAT MATCHES THE TV ON THE VC DISPLAY, i.e. the GTDisc.
Open the disc tray on the Blu-ray Home Theater and install the disc.
If the tray is locked, see below for instructions on how to unlock thetray.
Press “Input” on the TV remote, and then select “HDMI 1.”
Ensure the disc plays a clear HD picture on the TV, and that sound iscoming out of the speakers.
IF YOU CANNOT INSTALL THE NEW DISC, leave it with the store manager.
STEP 3: Lock/Unlock the Disc Tray
With the disc playing, press and hold the “PLAY” button and the “OPEN/CLOSE” button on the Main Unit.
Hold for approximately 5 seconds.
The LED will read “LOCKED.”
Repeat the same sequence to UNLOCK the tray.
Make sure you PRINT and LEAVE the Tray Lock Leave Behind document with the store so they know the process too!
Select HDMI 1 Input
Remove (4) Allen Screws New Graphic
TV Model Indicated HERE - Install Graphic that matches TV on 3D Display - i.e. GT Series
8/6/2019 8865 Instructions - Panasonic 2011 3D & VC Display Resets - 6th Avenue Electronics High Resolution[1]
http://slidepdf.com/reader/full/8865-instructions-panasonic-2011-3d-vc-display-resets-6th-avenue-electronics 16/17
16
Program Name: Panasonic 2011 3D and VIERA Connect (VC) Display Resets - 6th Avenue Electronics
Project Codes: 8865 Visit Dates: (05/09/11 - 05/12/11) Rep Support Hotline: 877-484-0232
Objective #9: Complete Final Settings, Ensure Full Functionality, and Perfect Displays
Complete STEP 1 for BOTH the 3D and VIERA CONNECT Displays.
STEP 1: Complete ARC Settings on the Blu-ray Home Theater
“ARC” stands for Audio Return Channel, which allows audio to pass automatically from the TV to the Home Theater via the HDMIcable.
Complete these settings:
Press “Menu” on the Blu-ray Home Theater remote.
Select “EXT IN”
Select “ARC”
If the disc doesn’t begin playing automatically, press the “DISC” button on the Blu-ray Home Theater remote, thenpress Play to resume disc playback.
Complete STEP 2 for the 3D Display ONLY.
STEP 2: Ensure Full 3D Functionality of 3D Display
Make sure the TV is playing a good, clear High-Definition 3D picture from the demo disc.
Ensure high-quality audio is coming from the Home Theater speakers and subwoofer.
Ensure the 3D Glasses on the pedestal are working, and that you can see a Full 3D HD picture on the TV when lookingthrough the glasses.
If the 3D Pedestal is not present, note that in your survey.
If a unit is not working, troubleshoot: turn off, unplug, plug back in, turn back on, ensure proper connections. If you need help,call the Rep Support Hotline.
Make sure there is nothing in front of the TV just underneath the Panasonic logo. That is where the emitters for the 3D glasses
are located. If the emitters are covered, the glasses will not be able to communicate with the TV and they will not work.
Complete STEP 3 for the VIERA CONNECT Display ONLY.
STEP 3: Ensure Full Functionality of VIERA Connect Display
Make sure the TV is playing a good, clear High-Definition 2D picture from the demo disc.
Ensure high-quality audio is coming from the Home Theater speakers and subwoofer.
If a unit is not working, troubleshoot: turn off, unplug, plug back in, turn back on, ensure proper connections. If you need help,call the Rep Support Hotline.
Blu-ray Home Theater Menu - Select EXT IN Select ARC
8/6/2019 8865 Instructions - Panasonic 2011 3D & VC Display Resets - 6th Avenue Electronics High Resolution[1]
http://slidepdf.com/reader/full/8865-instructions-panasonic-2011-3d-vc-display-resets-6th-avenue-electronics 17/17
Program Name: Panasonic 2011 3D and VIERA Connect (VC) Display Resets - 6th Avenue Electronics
Project Codes: 8865 Visit Dates: (05/09/11 - 05/12/11) Rep Support Hotline: 877-484-0232
Objective #9 CONTINUED: Complete Final Settings, Ensure Full Functionality, and Perfect Displays
Complete STEPS 4 and 5 for BOTH the 3D and VIERA CONNECT Displays.
STEP 4: Reattach the Access Panel on BOTH DISPLAYS
Double check your WIRE MANAGEMENT! There should not be ANY wireshanging from the display. All wires should be neatly concealed inside the AccessPanel. (The wire shown at right is from the subwoofer - when you slide the sub-woofer into place under the shelf, push ALL of the excess wire into the small wirehole below the Access Panel.)
Once all wires are inside and the displays are fully functional, reattach the AccessPanel you removed earlier.
Make sure you reattach the panel on BOTH DISPLAYS!!
STEP 5: Ensure a Perfect Display
Slide the subwoofer into place underneath the shelf in front of the Access Panel, and behind the lower Panasonic graphic.
Note if any display parts are missing or need replaced. Indicate IN DETAIL which parts are needed in your survey.
Objective #10: Take Photos of BOTH Displays, Review Work with Store Manager
PHOTOS ARE REQUIRED!
Ensure you capture photos of BOTH the 3D and VIERA Connect Displays.
Make sure you attach at least one photo that shows the ENTIRE 3D Display with the Eyewear Pedestal and the ENTIRE VIERA
Connect Display. Include close-up shots as well to demonstrate the need for parts or maintenance, or to highlight good wire management.
Review your work with the store.
Give the store the Tray Lock Leave Behind document. Get a manager sign-off.
GIVE THE STORE THE WIRELESS LAN ADAPTERS from the new 2011 TVs you installed, if you haven’t already. Explain tothe store that they need those adapters to sell the TVs, once they are ready to come off the displays.
Thank you for participating in the Panasonic 3D and VIERA Connect Display Reset Projects!
Access Panel BELOW SHELF