95-2001...2 Open drivers door and remove fuse panel on end of dash. 4 Remove (1) Phillips screw from each side exposed. 5 Remove (3) screws from top of glove box liner. 6 Remove (2)

INSTALLATION INSTRUCTIONS FOR PART 95-2001

95-2001

APPLICATIONSGM

MULTI KIT

KIT FEATURES

• Double DIN Head Unit Provision• Stacked ISO DIN Head Unit Provision

• A) Double DIN Brackets • B) Double DIN Trim Plate • C) Spacers • D) (3) Screws-(3) Speed Clips

KIT COMPONENTS

A

TOOLS REQUIRED:• Phillips Screwdriver • Socket Set

1-800-221-0932 © COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION

www.metraonline.com

B

WIRING AND ANTENNA CONNECTIONS(Sold Separately)

• Wiring Harness - Please see www.metraonline.comfor specific interface applications

• Antenna Adapter -• 40-GM10 - GM Antenna Adapter 1988-up

• 40-CR10 - Chrysler Antenna Adapter 2002-up

C D

METRA. THE WORLD’S BEST KITS.™

BUICKCentury 1997-2005 3 Le Sabre 1995-2005 4,5Park Avenue 1995-2005 4,5Regal 1995-2004 3Rendezvous 2002-2007 6Riviera 1996-1999 7Roadmaster 1995-1996 8Skylark 1996-1998 9

CADILLACEscalade/EXT 2003-2006 10

CHEVROLET Avalanche 2003-2006 10Blazer 2003-2005 11Blazer (Double DIN) 2002-2002 11Cavalier 2000-2005 12Colorado 2004-2009 13Express Van (full size) 2001-2007 14,15Impala 2000-2005 16Malibu 2001-2003 17Malibu Classic 2004-2005 17Monte Carlo 2000-2005 18SSR 2003-2006 19S-10 Pickup with DDIN Radio 2002-2004 11Silverado (all) 2003-2006 8Silverado (Classic) 2007 8Suburban 2003-2006 8Tahoe 2003-2006 8Trailblazer 2002-2009 20Venture 2000-2005 21,22

GMCCanyon 2004-2009 13Envoy 2002-2009 23Savanna 2001-2007 14,15Sierra 2003-2006 8Sierra (Classic) 2007 8Sonoma (Double DIN)) 2002-2003 11Yukon/Denali/XL 2003-2006 8

HUMMERH2 2003-2007 24,25ISUZUAscender 2003-2008 23

OLDSMOBILEAchieva 1996-1998 26Alero 1999-2004 27Aurora 1995-2003 28Bravada 1998-2001 11Bravada 2002-2004 23Cutlass 1997-1999 29Cutlass Supreme 1995-1997 29Eighty-Eight 1994-1999 30Intrigue 1998-2002 31LSS 1996-1999 32Ninety-Eight 1994-1996 30Regency 1997-1998 32Silhouette 2000-2004 21,22

PONTIACAztec 2001-2005 33Bonneville 2000-2005 34Grand Am 2001-2005 35Montana 2000-2005 21,22Sunfire 2000-2005 36

Kit AssemblyDOUBLE DIN/STACKED ISO DIN HEAD UNIT PROVISION . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

95-2001

*Note: Refer also to the instructions included with the aftermarket radio.

KNOWLEDGE IS POWEREnhance your installation and fabrication skills byenrolling in the most recognized and respectedmobile electronics school in our industry.Log onto www.installerinstitute.com or call800-354-6782 for more information and take stepstoward a better tomorrow.

VEHICLE APPLICATION CONTENTS

Dash Disassembly

Metra recommends MECPcertified technicians.

95-2001 DASH DISASSEMBLY

BUICK • CENTURY 1997-2005 / REGAL 1995-2004

3

1

Unsnap the top edge of the knee bolster panel.

Disconnect the negative battery terminal to prevent an accidentalshort circuit.

3

Remove the plastic trim piece to theleft of the glove box and (1) Phillipsscrew exposed.

2

Remove (1) Phillips screw from thepanel.

4

Remove the ashtray cluster and (2)Phillips screws from each side.

5

Unclip the entire dash trim bezel andremove.

6

Open doors and unsnap end capsfrom each side of dash.

7

Unsnap and remove radio/instrumentcluster panel.

8

Remove (3) screws in order to removeradio.

9

Continue to kit assembly.

4


BUICK • LESABRE / PARK AVENUE 1995-1999

1

Pop out the a/c vents and remove (1)Phillips screw exposed in each ventcavity.


3

Unsnap the climate control trim panel(from door to door) and remove (4) Phillips screws exposed.

2

Unclip the radio trim bezel and remove. 4

Remove the screws securing the fac-tory head unit and disconnect thewiring.

5


5


BUICK • LESABRE / PARK AVENUE 2000-2005

1

Unsnap and remove trim along centerof dash. (One piece on right and oneon left of wheel)


3

Open drivers door and unsnap andremove dash end cap.

2

Unsnap and remove radio/instrumentbezel.

4

Remove (2) screws in order to removeradio.

5


6


BUICK • RENDEZVOUS 2002-2007

1

Remove liners from cup holders and storage pocket next to cup holders,then remove screws. Unsnap and remove panel.

Disconnect the negative battery terminal to prevent an accidental short circuit.

3

Open center console and remove 2 screws at front of console opening.2

Remove (2) screws from bottom of radio/climate control bezel, unclip and remove.4

Remove (3) 9/32" hex head screws to remove radio.5


7


1

Remove (1) Phillips screw and unsnap right side panel to expose (1) Phillips screwbeneath panel and remove.


3

Unsnap left side panel exposing (1) Phillips screw to remove.2

Unsnap underside of overhanging dash to unsnap (6) plastic rivets and removepanel.

4

Remove (5) hex head screws now exposed under overhang.5

Unsnap bottom edge of trim bezel, then while holding overhang up, unsnap andremove trim bezel by removing any necessary harnesses.

6

Remove (3) Phillips screw to remove climate control.7

Remove (2) Phillips screws to remove rear support and (3) 9/32" hex head screwsto remove radio.

8


BUICK • RIVIERA 1996-1999

8


1

Unclip panel below steering column and remove.


3

Unclip dash panel sides and remove.2

Remove (2) 7mm screws above instrument cluster.4

Set parking brake, turn car on, and move shifter to the lowest gear. Tilt steering wheel down then unsnap entire instrument cluster/radio panel and remove.

5

Remove (3) 7mm screws to remove radio.6


BUICK • ROADMASTER 1995-1996

9


1

Under glove box and drivers knee bol-ster, remove (2) plastic panels by turning (2) 1/4 turn fasteners per side.


3

Remove (6) 9/32" screws inside glovebox.

2

Remove (4) 9/32" screws revealed.(2 per side).

4

Unsnap panel from driver's side topassenger's side.

5

Remove (3) 9/32" screws to removeradio.

6


BUICK • SKYLARK 1996-1998

10


1

Remove (3) 9/32" screws and removeradio.


3

Unsnap and remove dash bezel.2


CADILLAC • ESCALADE 2003-2006CHEVROLET • AVALANCHE 2003-2006

SILVERADO 2003-2006 / SUBURBAN 2003-2006SILVERADO (CLASSIC) 2007

TAHOE 2003-2006 GMC • SIERRA 2003-2006SIERRA (CLASSIC) 2007

YUKON / DENALI / XL 2003-2006

11


1

Pull down on the panel and removethe 9/32" hex-head screws exposedon the bottom of the dash trim bezel.


3

Remove (2) 9/32" hex-head screwsfrom the knee bolster panel.

2

Remove (1) Phillips screw above theinstrument cluster.

4

Unclip the dash trim bezel andremove.

5

Remove (2) 9/32" hex-head screwssecuring the factory head unit anddisconnect the wiring.

6

CHEVROLET • BLAZER 2003-2005 •BLAZER 2002 (WITH DOUBLE DIN RADIO) S-10 2002-2004 (WITH DOUBLE DIN RADIO)

GMC • SONOMA (WITH DOUBLE DIN RADIO) 2002-2004


12


1

Open passenger door and remove panel on end of dash.


3

Open drivers door and remove fuse panel on end of dash. 2

Remove (1) Phillips screw from each side exposed. 4

Remove (3) screws from top of glove box liner. 5

Remove (2) screws from the top-left corner of the glove box cavity. 6

Remove (1) Phillips screw from the defroster duct. 7

Remove the ductwork and (1) Phillips screw exposed. 8

Remove the dash pad and (3) Phillips screws exposed at the top of the radio trimbezel.

9

CHEVROLET • CAVALIER 2000-2005



13

1

Remove (3) 9/32”screws securing the radio to remove. (Figure B)


3

Unsnap and remove the entire panel surrounding the radio and A/C controls. (Figure A)

2

CHEVROLET • COLORADO 2004-2009GMC • CANYON 2004-2009


14


1

Unsnap radio/climate/instrument panel.


3

Unsnap and remove small trim panel below steering column.2

Move shift lever to first gear position.4

Rotate panel counterclockwise to lift over steering column and remove.5

Remove (3) 9/32" hex head screws to remove radio.6


CHEVROLET • EXPRESS VAN 2001-2002GMC • SAVANNA 2001-2002

15


1

Remove (2) 10mm bolts from panel below passenger dash airbag and removepanel.


3

Remove (2) 10mm bolts from below knee bolster under steering column and remove panel.

2

Remove (2) 10mm nuts from inside center pocket between power outlets.4

Unsnap and remove radio and instrument cluster panel. (May not be necessaryto completely remove radio and instrument cluster panel to access radio.)

5

Remove (3) 9/32" bolts to remove radio.6


CHEVROLET • EXPRESS VAN 2003-2007GMC • SAVANNA 2003-2007

16


1

Remove (2) Phillips screws under theinstrument cluster.

Disconnect the negative batteryterminal to prevent an accidentalshort circuit.

3

Unclip each side of the dash trimbezel (fuse access) and remove (1)Phillips screw exposed on each side.

2

Unclip the trim panel above thepedals. (It is not necessary to removethe panel it can be left hanging).

4

Remove (2) Phillips screws from theknee panel.

5

Unclip the knee panel and remove (1)phillips screw exposed on the rightside of the steering column.

6

Unclip and remove the entire dashtrim bezel.

7

CHEVROLET • IMPALA 2000-2005


17


1

Remove (3) bolts and remove radio.


3

Unsnap and remove radio bezel.2

CHEVROLET • MALIBU 2001-2003MALIBU CLASSIC 2004-2005


18


1

Remove (2) 9/32" screws from theknee panel and unclip the panel.


3

Unclip the trim panel above the ped-als. (It is NOT necessary to removethe panel it may be left hanging).

2

Unsnap the driver's side fuse panelcover and remove (1) 9/32" screw.

4

Open the glove box and remove (1)9/32" screw from the upper left corner.

5

Remove (3) 9/32" screws securingthe factory radio and disconnect thewiring.

6

CHEVROLET • MONTE CARLO 2000-2005


19


1 23

1 23

1

Unclip and remove the long trim panelbelow the radio and passenger airbag. (Figure B)


3

Unclip and remove the (3) climatecontrol knobs. (Figure A)

2

Unclip and remove the small trimpanel to the left of the steeringwheel. (Figure C)

4

Remove the (5) 9/32” screws securingthe radio/instrument panel then unclipand remove the panel. (Figure D)

5

Remove the screws securing the factory head unit and disconnect thewiring.

6

CHEVROLET • SSR 2003-2006


A

B

CD

20


1

Remove (1) Phillips screw under climate controls to the left of the power outlet.


3

Remove (2) Phillips screws inside instrument cluster.2

Remove (2) 7mm hex heads from under steering column and lower the panel.Remove (3) Phillips screws around steering wheel.

4

Unsnap and remove bezel. (Use caution pulling over hazard switch.) Remove (3)7mm hex head screws to remove radio.

5


CHEVROLET • TRAILBLAZER 2002-2009

21


1

Remove (1) Phillips screw from thecigarette lighter compartment.


3

Remove the ashtray and (1) phillipsscrew exposed in the ashtray cavity.

2

Remove (2) Phillips screws securingthe factory head unit and disconnectthe wiring.

4

CHEVROLET • VENTURE 2000OLDSMOBILE • SILHOUETTE 2000

PONTIAC • MONTANA (EXCEPT SV6) 2000


22


1 Disconnect the negative battery terminal to prevent an accidental short circuit.

CHEVROLET • VENTURE 2001-2005OLDSMOBILE • SILHOUETTE 2001-2004

PONTIAC • MONTANA (EXCEPT SV6) 2001-2005

Remove (1) Phillips screw from the cigarette lighter compartment. 3

Remove the ashtray and (1) phillips screw exposed in the ashtray cavity. 2

Remove (2) Phillips screws securing the factory head unit and disconnect thewiring.

4


23


GMC • ENVOY 2002-2009 / ISUZU ASCENDER 2003-2008OLDSMOBILE • BRAVADA 1998-2004

2. Remove (4) Phillips screws, (2) from left and (2) from right of carpeted panel.

3. Slide carpeted panel down and backwards to reveal (2) Phillips screws and remove.

4. Unsnap radio bezel and unplug cigarette lighter and accessories.

5. Remove (3) screws and remove radio.


1 Disconnect the negative battery terminal to prevent an accidental short circuit.

24


HUMMER • H2 2003-2007

1

Remove (4) phillips screws from hinge on console door inside console and removedoor.


3

Open center console and remove (4) 9/32” screws from console box and remove box.

2

Loosen (1) T-15 torx on forward facing side of shift lever and pull up to remove.

4

Unclip cup holder/shifter trim assembly and remove.5

Remove (6) Phillips screws from top of center console.6

Remove (2) Phillips screws from inside pocket on back of center console, thenunclip and remove.

7

Continued on page 30.

25



HUMMER • H2 2003-2007

8

Slide control assembly rearwards.

Remove (1) 10mm bolt to right of shift lever.

10-

Remove (2) Phillips screws from under console box on drivers side and (2) Phillips screws from under console trimtop on passenger side.

9

Remove (2) T-30 torx bolts from top of rado/climate control trim andunclip and remove.

11

Remove (3) 9/32” screws that hold the radio in.12

Continued from page 30.

26


OLDSMOBILE • ACHIEVA 1996-

1

Remove (10) torx-head screws fromthe glove box location.


3

Open the glove box, press inward onthe walls of the glove box liner andremove the liner.

2

Remove (2) 9/32" hex-head screwsunder the steering column.

4

Unclip the dash trim bezel. 5

Remove the screws securing the factory head unit and disconnect thewiring.

6


27


OLDSMOBILE • ALERO 1999-2004

1

Unclip and remove shifter trim panel.


3

Remove shift knob by using a smallscrewdriver to remove U-clip fromfront of shifter and pull upward.

2

Unclip and remove radio and climatecontrol panel by pulling from bottom.

4

Remove (3) 9/32" screws from radioand remove.

5


28


OLDSMOBILE • AURORA 1995-2003

1

Remove (2) 7mm screws securing thefactory head unit and disconnect thewiring.


3

Unclip the radio trim bezel andremove the bezel.

2


29


OLDSMOBILE • CUTLASS 1997-1999CUTLASS SUPREME 1995-1997

1

Remove (2) ) 9/32" hex-head screwssecuring the factory head unit anddisconnect the wiring.


3

Unclip the radio trim bezel andremove.

2


30


OLDSMOBILE • EIGHTY EIGHT 1994-1999

1

Remove (2) ) 9/32" hex-head screws securing the factory head unit and disconnectthe wiring.


3

Unclip the radio trim bezel and remove.2


1

Unsnap the wood trim and remove.


3

Open the glove box and remove (2) hex-head screws securing the wood trim. 2

4

Remove (3) Phillips hex-head screws securing the factory head unit and disconnectthe wiring.

Remove (2) hex-head screws below the radio trim bezel.

6

Lift up on the bezel and remove. 5


OLDSMOBILE • NINETY EIGHT 1994-1996

31


OLDSMOBILE • INTRIGUE 1998-2002

1

Remove the center console.


3

Open the center console storagecompartment and remove (2) 9/32"hex-head screws exposed.

2

Unclip the radio trim bezel andremove.

4

Remove (2) 9/32" hex-head screwssecuring the factory head unit anddisconnect the wiring.

5


32


OLDSMOBILE • LSS 1996-1999 / REGENCY 1997-1998

1

Unsnap and remove radio trim bezel.


3

Open glove box and remove two-center trim bezels attached by screws.2

Remove (3) 9/32" hex-head screws and remove radio.4


33


PONTIAC • AZTEC 2001-2005

1

Remove (1) Phillips screw exposedinside bottom cup holder.


3

Pull out cup holder inserts.2

Unsnap and remove shifter trim withcup holders.

4

Remove (2) #15 torx at bottom ofradio/climate bezel.

5


34


PONTIAC • BONNEVILLE 2000-2005

1

Unclip the ignition trim and remove.


3

Remove (2) Phillips screws from the instrument cluster. 2

Unclip the climate control/radio trim bezel and remove. 4

Depress the spring clips on each side of the factory head unit and remove.5


35


PONTIAC • GRAND AM 2001-2005

1 Disconnect the negative battery terminal to prevent an accidentalshort circuit.

Unsnap and remove radio trim bezel.2

Remove (3) 9/32” screws from radiobrackets and remove radio.

3


36


PONTIAC • SUNFIRE 2000-2005

1 Disconnect the negative battery terminal to prevent an accidentalshort circuit.

Open the glove box and remove (2)Phillips screws exposed on the rightedge of the radio trim bezel.

2

Unclip the bezel and remove. 3

Remove (2) 7mm hex-head screwssecuring the factory head unit anddisconnect the wiring.

4


37

95-2001 KIT ASSEMBLY

DOUBLE DIN HEAD UNIT PROVISIONSTACKED ISO DIN HEAD UNIT(S) PROVISION

Locate the factory wiring harness inthe dash. Metra recommends usingthe proper mating adapter from Metraor AXXESS. Re-connect the negativebattery terminal and test the unit forproper operation.

1

Attach the Double DIN brackets to theinside edge of the Double DIN trimplate. (Figure A)

2

Slide the Double DIN head unit orstacked ISO head units into the brack-et/radio housing assembly and securethe Double DIN head unit or stackedISO head units to the assembly usingthe screws supplied with the radio.(Figure B)

3

Reassemble dash in reverse order ofdisassembly.

4

Note: For the Buick Le Sabre,Oldsmobile Aurora and the PontiacBonneville the (3) speed clips andscrews provided with the kit willneed to be installed into the subdash where the screw holes line upon the kit.

Note #2 -: The spacers included inthis kit may be necessary to adaptto the slight differences from onevehicle to another. If the kit/ radioassembly does not meet the back-side of the factory radio opening,use the spacer to eliminate thatspace.

*Note: Refer also to the instructions included with the aftermarket radio.

A

B

95-2001 INSTRUCTIONS

1-800-221-0932 REV. 12/02/09 © COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION INST95-2001

www.metraonline.com

METRA. THE WORLD’S BEST KITS.™

Documents

95-2001...2 Open drivers door and remove fuse panel on end of dash. 4 Remove (1) Phillips screw from each side exposed. 5 Remove (3) screws from top of glove box liner. 6 Remove (2)