9X-9591 _ Electrical Converter Gp _ Pulse Width Modulated _ Special Instruction _ REHS3413-00 _ August 2007 _ CATERPILLAR

8/20/2019 9X-9591 _ Electrical Converter Gp _ Pulse Width Modulated _ Special Instruction _ REHS3413-00 _ August 2007 _ C…

http://slidepdf.com/reader/full/9x-9591-electrical-converter-gp-pulse-width-modulated-special-instruction 1/5

Instruções Especiais Wiring the 9X-9591 Electrical Converter Gp (PULSE WIDTH MODULATED){1421, 1901, 7490}

Wiring the 9X-9591 Electrical Converter Gp (PULSE WIDTH MODULATED){1421, 1901, 7490}

SMCS - 1421; 1901; 7490

Engine:3512B (S/N: 1PW1-UP; CMC1-UP; S2J1-UP; S2K1-UP; S2L1-UP; S2N1-UP; 4TN1-UP; 6GW1-UP)

3126B (S/N: BEJ1-UP; DCS1-UP)3412 (S/N: 4BZ1-UP)3412C (S/N: 9EP1-UP; BCW1-UP)3508B (S/N: CNB1-UP; S2D1-UP; S2E1-UP; 3DM1-UP; 6PN1-UP; 5PS1-UP; 3DW1-UP; 5KW1-UP)3508C (S/N: LLC1-UP)3516B (S/N: CBN1-UP; 9AN1-UP; 2FW1-UP; S2X1-UP)C-10 (S/N: BCX1-UP)C-12 (S/N: BDL1-UP)

Generator Set:3406E (S/N: 8AZ1-UP)3456 (S/N: C1G1-UP; C3G1-UP; CAH1-UP)C18 (S/N: G4C1-UP; STM1-UP)C32 (S/N: SXC1-UP)C9 (S/N: C9A1-UP)

Industrial Engine:

C-15 (S/N: BEM1-UP)C-16 (S/N: BFM1-UP)C9 (S/N: JSC1-UP)

Marine Engine:3406E (S/N: 9WR1-UP)C18 (S/N: CKH1-UP)

Introduction

Do not perform any procedure in this Special Instruction until you read this information and you understand this information.

The 9X-9591 Electrical Converter Gp (PULSE WIDTH MODULATED) is used in some marine, industrial, and generator set applications. Theconverter is used in order to provide local speed control and remote speed control. The converter provides the inputs for desired speed and droop signal

to the engine's Electronic Control Module (ECM).

Fechar o SIS

Tela anterior

produtos: GENERATOR SETModelo: C32 GENERATOR SET SXCConfiguração: C32 Generator Set SXC00001-UP

Número de Mídia -REHS3413-00 Data de Publicação -24/08/2007 Data de Atualização -26/08/2007

i02825385

Página 1 de 5C32 Generator Set SXC00001-UP(SEBP4326 - 08) - Estrutura do Documento

11/22/2008https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/media...



The output for the desired speed signal (S terminal) is a PWM (pulse width modulation) signal that is approximately between 5 percent and 95 percentduty cycle at a constant frequency. This speed signal varies with the position of an external potentiometer that is connected to terminals 1, 2, and 3. TheECM calculates the desired engine RPM from the signal from the S terminal when the duty cycle is between 5 percent and 95 percent. If the ECM readsthe S terminal signal as invalid, the ECM will take action based upon application and may set engine speed low idle.

The output for droop (D terminal) is a PWM signal between 5 percent and 95 percent duty cycle at a constant frequency. The output of the droop signalvaries with the position of an internal potentiometer. The ECM calculates the desired engine RPM from the D terminal signal. If the ECM reads the Dterminal signal as invalid, the engine will run in isochronous mode.

Note: The droop PWM signal may not be used in all applications.

Incorrect Wiring

If the external potentiometer is not wired correctly the inability to run the engine at the customer specified engine speeds may occur.

For example by turning the potentiometer clockwise the engine speed may decrease. Refer to Illustration 2.

Illustration 1 g01409622

(S) Terminal - desired speed output. Controlled by an external 1K or 2K potentiometer

(D) Terminal - droop output. Controlled by an internal 2K potentiometer





Correct Wiring

1. Verify that the external potentiometer is wired correctly to terminals 1, 2, and 3 of the PWM converter. Refer to Illustration 3 for the correctwiring of the external potentiometer to the PWM converter.


Incorrect wiring





a. By turning the wiper clockwise, the resulting voltage will increase. The resistance between terminal 2 and terminal 3 will go down.This will indicate that the connection is between the terminal signal and the high side of the potentiometer. The system response willbe an increase in engine RPM.

b. By turning the wiper counterclockwise, the resulting voltage will decrease. The resistance between terminal 2 and terminal 1 will go

up. This will indicate the connection is between the terminal signal and the low side of the potentiometer. The system response will bea decrease in engine RPM.

2. Conduct any additional functional testing and troubleshooting referring to the engine's Troubleshooting manual for further information inregards to PWM converter.


Correct wiring





Direitos Autorais 1993 - 2008 Caterpillar Inc.Todos os Direitos Reservados.Rede Particular Para Licenciados SIS.

Sat Nov 22 20:06:53 UTC-0300 2008


11/22/2008h // i / i b/ i b/ hd / hd i j ? l / i b/ i b/ di

Documents

9X-9591 _ Electrical Converter Gp _ Pulse Width Modulated _ Special Instruction _ REHS3413-00 _ August 2007 _ CATERPILLAR