1 2 3

1

2

UT-6408-POE 8 POE

8 PoE IEEE

802.3af/at PD

IEEE 802.3af/at POE

IEEE 802.3 10BaseT

IEEE 802.3u 100BaseT(X)

8 RJ-45( POE ) 10/100Base-T

LED PWR1 PWR2 FAIL RJ-45

POE

1A @ 24VDC

POE + 1 2 pins - 3 6 pins

46 57VDC 3A@48V max

1 6

IP30

\

-40 85

-40 85

5 95% ( )

EMI FCC Part 15 Subpart B classA EN55022 class A

EMS

IEC(EN)61000-4-2(ESD)

IEC(EN)61000-4-3(RS)

IEC(EN)61000-4-4(EFT)

IEC(EN)61000-4-5(Surge)

IEC(EN)61000-4-6(CS)

IEC(EN)61000-4-8

IEC 60068-2-27(Shock)

IEC 60068-2-32(Freefall)

IEC 60068-2-6(Vibration)

a. PWR1 PWR2

b. FAIL

c. RJ-45 100 Base

10 Base

d. POE1 8 RJ-45 POE

5.9in5.9in1.87in3.9

3in

3.9

3in

150.00150.0047.6047.601

00

.00

10

0.0

0

1 2 3

. Installation

1.DIN-Rail

Tighten the rail to the device by screws

Push the bottom of the device rail to fixed rail.

Then push it into the rail slightly again

2. Wall Mounted

Tighten the metal fixation strip with screws as shown above.

Then hang the machine with locked metal strip on the wall

or machine cabinet.

UT-6408-POE10/100M 8-Port Industrial POE Switch

User Manual

Overview

UT-6408-POE is a 8-port industrial grade unmanaged POE Ethernet

switch with reverse polarity protection of AC or DC input for avoiding

being standard snap-fit-mounting and wall-mounting installation, so it's

very easy to be installed and used in any industrial networks.

. Main FeaturesStandards:

Port:

Ethernet Port: 8x10/100 Base-TX RJ-45 ports(POE output)

Alarm contact: 1 channel relay output, NO NC capacity 1A@ 24VDC

POE Power: +(1, 2) pins; -(3, 6) pins

Power requirement:

Voltage Input : 46-57VDC, redundant dual power input, 3A@48Vmax

Terminal Block: 1 pluggable 6-pin

Overload protection: Yes

Reverse Polarity Protection: Yes

Characteristics:

IP Rating: IP30

Installation: DIN-Rail/wall mounted

Environment:

Operating Temperature:

Storage Temperature:

Relative Humidity: 5%-95%(Non-condensing)

Industrial Standards:

IEEE 802.3af/at POE

IEEE 802.3 10BaseT

IEEE 802.3u 100BaseT(X)

EMI FCC Part 15 Subpart B classA EN55022 class A

EMS

IEC(EN)61000-4-2(ESD)

IEC(EN)61000-4-3(RS)

IEC(EN)61000-4-4(EFT)

IEC(EN)61000-4-5(Surge)

IEC(EN)61000-4-6(CS)

IEC(EN)61000-4-8

IEC 60068-2-27(Shock)

IEC 60068-2-32(Freefall)

IEC 60068-2-6(Vibration)

. Dimension

. Indicator

a. PWR1, PWR2 on, it shows the power is on and normal

b. FAIL indicator on, it shows the power is break down or one

channel is disconnected

c. a.RJ-45: when access to Internet, green indicator on the left will be

on under 100 Base, but not for 10 Base; the yellow indicator on the

right indicates network data communication, when the device access

to Internet, yellow indicator is blinking; without access to Internet,

yellow and green indicators will not on.

d. POE1-8 indicators will be on when RJ-45 ports provides with POE output

. Power Connection

Industrial Ethernet switch supports 46-57V DC input, and it is with reverse polarity protection. a. Connect the positive/negative polarity to V+ and V- terminals respectivelyb.Tighten the screw to avoid bad connection Both side of is for power alarm signal output, when the power is breakdown, or 1 channel is without power on, it will be alarmed.

5.9in5.9in1.87in3.9

3in

3.9

3in

150.00150.0047.6047.601

00

.00

10

0.0

0