Upload
vuonglien
View
215
Download
0
Embed Size (px)
Citation preview
36 3736 37
KERLITE Cotto d’Este > KERLITE Technical Manual
How to read the attachment
At the discretion
of I.S.
Manufac-turer
Size of slabs(cm)
Product(*)
Primer, if necessary(*) Mixing ratio (**) Class
(*)
Nominal cover-age (*)
Setting for foot
traffic and workability
(***)
Ready for use (***)
Installation(*)
01 02 03 04 05 06 07 08 09 10 11
01_ The installation supervisor must examine the conditions of the work site to choose between a normal setting adhesive or a quick setting
02_ List of adhesive manufacturers.
03_ Depending on the adhesive recommended by the manufacturer, you will find the size in cm of the slab.
04_ List of adhesives recommended by manufacturers based on the intended use and size of slabs.
05_ List of primers to use before adhesive application, as indicated by manufacturers for each intended use.
06_ The mixing ratio refers to a single product unit (a bag, a can, etc.), in order to obtain the characteristics declared by manufacturers.
07_ The adhesive's class under the UNI EN 12004 standard is indicated (see Sheet below “About ADHESIVES”).
08_ You will find an indication of how many square metres you can install with a single product unit prepared with the established mixing ratio.
09_ You will find the time that must pass before treading on the surface to fill joints with grout.
10_ You will find the time that must pass before using the floor, i.e. before it can go subject to static and/or dynamic stress.
11_ You will find the installation method and features of the trowel to use for each adhesive.
About ADHESIVES
Adhesives are divided into THREE CLASSES, depending on their composition, as established by the UNI EN 12004 standard:
CEMENTITIOUS (C): mixture of hydraulic binding agents, aggregates and organic additives (note to be mixed with water or other liquid additive immediately before use)
REACTIVE (R): mixture of synthetic resin, mineral fillers and organic additives, which harden due to a chemical reaction (note: these adhesives may have one or more components)
DISPERSION (D): mixture of binding and organic agents, namely polymers in aqueous dispersion, organic additives and mineral fillers (note: ready-to-use mixtures)
Depending on their features, adhesives are thus classified:
Class 1: normal setting
Class 2: improved setting properties
There are three additional classes:
Class F: quick setting adhesives
Class T: slip resistant adhesives
Class E: adhesives with extended open time
There is a fourth additional class for cementitious adhesives only: adhesives can be classified as DEFORMABLE (S) and divided on the basis of test results under the UNI EN 12002 standard:
Class S1: deformable adhesives
Class S2: highly deformable adhesives
Adhesives attachment
WALL INSTALLATION (*)For NEW BUILDINGS and REFURBISHING, for installation on pre-existing walls
Interiors
Any residential and commercial environment, in situations where holes and/or cuts are not necessary.
KERL
ITE
3mm
Two-coat plaster, gypsum plaster, plasterboard, fibre cement panels Page 36
Concrete, old ceramic tile, marble, stone Page 37
Particle board, metal Page 38
Any residential and commercial environment, in situations where holes and/or cuts are necessary.
KERL
ITE
3plu
sKE
RLIT
E 5p
lus Two-coat plaster, gypsum plaster, plasterboard, fibre
cement panels Page 39
Concrete, old ceramic tile, marble, stone Page 40
Particle board, metal Page 41
Exteriors
In situations where holes and/or cuts are not necessary and with sizes up to 100 x 100 cm.
KERL
ITE
3mm Plaster Page 42
Concrete Page 43
In situations where holes and/or cuts are necessary and/or for large sizes.
KERL
ITE
3plu
sKE
RLIT
E 5p
lus
Plaster Page 44
Concrete Page 45
FLOOR INSTALLATION (*)For NEW BUILDINGS and REFURBISHING, for installation on pre-existing floors
Interiors
Residential (kitchens, bathrooms, living rooms, common apartment block areas and any other residential environment).
KERL
ITE
3plu
sKE
RLIT
E 5p
lus
Cement-based screeds, calcium sulphate-based or heated screeds, self-levelling products, concrete, old ceramic tile, marble slabs, stone
Page 46
Light commercial (offices, offices open to the general public, waiting rooms, shops, bathrooms, restaurant dining rooms, car showrooms, bars, cinemas, surgeries/clinics).
Wood, PVC, rubber, linoleum, metal, resin Page 47
Intensive commercial (common areas of shopping centres, hotel halls, canteens, fast food restaurants, dance clubs, hospitals) with the exception of areas subject to heavy concentrated loads (e.g. trolleys with hard wheels). KE
RLIT
E 5p
lus Cement-based screeds, calcium sulphate-based or
heated screeds, self-levelling products, concrete, old ceramic tile, marble slabs, stone
Page 46
Wood, PVC, rubber, linoleum, metal, resin Page 47
Exteriors
Upon condition that surfaces are sheltered (e.g. loggias, covered balconies, etc.) and made totally impervious. The use of sizes that are not larger than 50x50 cm is recommended. KE
RLIT
E 3p
lus
KERL
ITE
5plu
s
Cement-based screeds, calcium sulphate-based or heated screeds, self-levelling products, concrete, old ceramic tile, marble slabs, stone
Page 46
Wood, PVC, rubber, linoleum, metal, resin Page 47
As a general rule that applies for all building materials to be secured in place with adhesive, there is no universal adhesive for installing KERLITE on all kinds of surface.Since it is not possible to describe all possible cases, we have provided information about the most common situations. First of all, we have divided installation cases into "walls" and "floors" and then into "interior" and "exterior". Depending on the rated stress, on any work to be performed subsequently and on the maximum dimension of the slab, we have assigned a certain type of KERLITE to each category. Starting from this classification, we have thus examined the most common kinds of supporting material. The resulting chart has been sent to all main manufacturers of adhesives that have, in turn, provided the most suitable product for each category.Please note that all solutions suggested have been submitted by adhesive manufacturers, who guarantee the indications given. For ex-planations or more information, contact the respect manufacturers (see “9 - Useful contacts”).
It is essential to follow all instructions given by adhesive manufacturers. This applies in particular to waiting time running before a surface can be walked on or grouted and the "Ready to use" time shown in the following tables.
( ) Products with special finishes can have limitations depending on their area of application. Refer to specific collection catalogues.
Nie ma uniwersalnego rodzaju kleju który służyłby do montażu KERLITE na wszystkich rodzajach powierzchni.Ponieważ nie jest możliwe opisanie wszystkich możliwych przypadków , podajemy informacje o najczęściej występujących sytuacjach. Przede wszystkim , podzieliliśmy przypadki użycia KERLITE na “ ścianach “ i na “podłogach” , a następnie na aplikacje “ wewnątrzne“ i “ zewnątrzne“. W zależności od obciążenia znamionowego, i maksymalnego wymiaru płyty , przypisaliśmy określony rodzaj KERLITE do każdej kategorii . Począwszy od tej klasyfikacji , zbadaliśmy najczęstsze rodzaje podłoża na które montowane są płyty KERLITE . Wynikowy wykres został wysłany do wszystkich głównych producentów klejów , którzy przewidzieli najbardziej odpowiedni produkt dla każdej kategorii .Proszę pamiętać, że wszystkie proponowane rozwiązania zostały złożone przez producentów kleju , którzy gwarantują poprawność wska-zanych danych ̀. Po wyjaśnienia i więcej informacji, skontaktuj się z producentami produktów ( patrz “ 9 - Przydatne kontakty “ ) .
istotnym jest, aby ściśle przestrzegać instrukcji podanych przez producentów kleji. Dotyczy to w szczególności czasu oczekiwania po którym po powierzchni można chodzić oraz czasu “gotowy do użycia” podanym w poniższych tabelach.
Każda przestrzeń mieszkaniowa i handlowa, w sytuacjach kiedy otwory i cięcia nie są potrzebne.
Dwuwarstwowe panele gipsowe, tynki gipsowe, płyty gip-sowo-kartonowe, płyty włókienno-cementowe
Strona 36
Strona 37
Strona 38
Strona 39
Strona 40
Strona 41
Strona 42
Strona 43
Strona 44
Strona 45
Strona 46
Strona 47
Strona 46
Strona 47
Strona 46
Strona 47
Beton, stare płytki ceramiczne, marmur, kamień naturalny
Płyty wiórowe, metal
Jastrychy cementowe, na bazie siarczanu wapnia lub ogrze-wane jastrychy, produkty samopoziomujące, beton, stare płytki ceramiczne, płyty marmurowe, kamienne
Jastrychy cementowe, na bazie siarczanu wapnia lub ogrze-wane jastrychy, produkty samopoziomujące, beton, stare płytki ceramiczne, płyty marmurowe, kamienne
Jastrychy cementowe, na bazie siarczanu wapnia lub ogrze-wane jastrychy, produkty samopoziomujące, beton, stare płytki ceramiczne, płyty marmurowe, kamienne
Drewna, PCV, guma, linoleum, metal, żywica
Drewna, PCV, guma, linoleum, metal, żywica
Drewna, PCV, guma, linoleum, metal, żywica
Dwuwarstwowe panele gipsowe, tynki gipsowe, płyty gip-sowo-kartonowe, płyty włókienno-cementowe
Beton, stare płytki ceramiczne, marmur, kamień naturalny
Płyty wiórowe, metal
Tynk
Tynk
Beton
Beton
Każda przestrzeń mieszkaniowa i handlowa, w sytuacjach kiedy otwory i cięcia są potrzebne.
W sytuacjach kiedy otwory i cięcia nie są potrzebne; w rozmi-arach do 100 x 100 cm
W sytuacjach kiedy otwory i cięcia są potrzebne; w rozmiarach większych
Mieszkaniowe (kuchnie, łazienki, pokoje dzienne, wspólne prz-estrzenie mieszkaniowe oraz inne środowiska mieszkaniowe
Handlowe / Komercyjne - małe użycie (biura, urzędy publiczne, poczekalnie, sklepy, łazienki, przestrzenie restauracyjne, salony samochodowe, bary, kina, gabinety / kliniki)
Handlowe / Komercyjne - intensywne użycie (centra handlowe, sale hotelowe, stołówki, restauracje fast food, kluby taneczne, szpitale), z wyjątkiem obszarów podlegających dużym obciąże-niom (np. wózków z twardymi kołami)
Pod warunkiem, że powierzchnie są zadaszone (np. loggie, bal-kony) i wykonane z całkowicie nieprzepuszczalnych materiałow. Zaleca się stosowanie rozmiarów, które nie są większe niż 50x50 cm.
produkty w specjalnych wykończeniach mogą mieć ograniczenia w zależności od obszaru zastosowania. proszę odnieść się do konkretnych katalogów kolekcji.
Wewnątrz
Wewnątrz
Zewnątrz
Zewnątrz
AplikAcje ścienneW nowych budynkach oraz podczas remontów, montaż na istniejących materiałach ściennych.
AplikAcje pODŁOGOWeW nowych budynkach oraz podczas remontów, montaż na istniejących materiałach podłogowych
Kleje - dodatkowe informacje
36 3736 37
KERLITE Cotto d’Este > KERLITE Technical Manual
How to read the attachment
At the discretion
of I.S.
Manufac-turer
Size of slabs(cm)
Product(*)
Primer, if necessary(*) Mixing ratio (**) Class
(*)
Nominal cover-age (*)
Setting for foot
traffic and workability
(***)
Ready for use (***)
Installation(*)
01 02 03 04 05 06 07 08 09 10 11
01_ The installation supervisor must examine the conditions of the work site to choose between a normal setting adhesive or a quick setting
02_ List of adhesive manufacturers.
03_ Depending on the adhesive recommended by the manufacturer, you will find the size in cm of the slab.
04_ List of adhesives recommended by manufacturers based on the intended use and size of slabs.
05_ List of primers to use before adhesive application, as indicated by manufacturers for each intended use.
06_ The mixing ratio refers to a single product unit (a bag, a can, etc.), in order to obtain the characteristics declared by manufacturers.
07_ The adhesive's class under the UNI EN 12004 standard is indicated (see Sheet below “About ADHESIVES”).
08_ You will find an indication of how many square metres you can install with a single product unit prepared with the established mixing ratio.
09_ You will find the time that must pass before treading on the surface to fill joints with grout.
10_ You will find the time that must pass before using the floor, i.e. before it can go subject to static and/or dynamic stress.
11_ You will find the installation method and features of the trowel to use for each adhesive.
About ADHESIVES
Adhesives are divided into THREE CLASSES, depending on their composition, as established by the UNI EN 12004 standard:
CEMENTITIOUS (C): mixture of hydraulic binding agents, aggregates and organic additives (note to be mixed with water or other liquid additive immediately before use)
REACTIVE (R): mixture of synthetic resin, mineral fillers and organic additives, which harden due to a chemical reaction (note: these adhesives may have one or more components)
DISPERSION (D): mixture of binding and organic agents, namely polymers in aqueous dispersion, organic additives and mineral fillers (note: ready-to-use mixtures)
Depending on their features, adhesives are thus classified:
Class 1: normal setting
Class 2: improved setting properties
There are three additional classes:
Class F: quick setting adhesives
Class T: slip resistant adhesives
Class E: adhesives with extended open time
There is a fourth additional class for cementitious adhesives only: adhesives can be classified as DEFORMABLE (S) and divided on the basis of test results under the UNI EN 12002 standard:
Class S1: deformable adhesives
Class S2: highly deformable adhesives
Adhesives attachment
WALL INSTALLATION (*)For NEW BUILDINGS and REFURBISHING, for installation on pre-existing walls
Interiors
Any residential and commercial environment, in situations where holes and/or cuts are not necessary.
KERL
ITE
3mm
Two-coat plaster, gypsum plaster, plasterboard, fibre cement panels Page 36
Concrete, old ceramic tile, marble, stone Page 37
Particle board, metal Page 38
Any residential and commercial environment, in situations where holes and/or cuts are necessary.
KERL
ITE
3plu
sKE
RLIT
E 5p
lus Two-coat plaster, gypsum plaster, plasterboard, fibre
cement panels Page 39
Concrete, old ceramic tile, marble, stone Page 40
Particle board, metal Page 41
Exteriors
In situations where holes and/or cuts are not necessary and with sizes up to 100 x 100 cm.
KERL
ITE
3mm Plaster Page 42
Concrete Page 43
In situations where holes and/or cuts are necessary and/or for large sizes.
KERL
ITE
3plu
sKE
RLIT
E 5p
lus
Plaster Page 44
Concrete Page 45
FLOOR INSTALLATION (*)For NEW BUILDINGS and REFURBISHING, for installation on pre-existing floors
Interiors
Residential (kitchens, bathrooms, living rooms, common apartment block areas and any other residential environment).
KERL
ITE
3plu
sKE
RLIT
E 5p
lus
Cement-based screeds, calcium sulphate-based or heated screeds, self-levelling products, concrete, old ceramic tile, marble slabs, stone
Page 46
Light commercial (offices, offices open to the general public, waiting rooms, shops, bathrooms, restaurant dining rooms, car showrooms, bars, cinemas, surgeries/clinics).
Wood, PVC, rubber, linoleum, metal, resin Page 47
Intensive commercial (common areas of shopping centres, hotel halls, canteens, fast food restaurants, dance clubs, hospitals) with the exception of areas subject to heavy concentrated loads (e.g. trolleys with hard wheels). KE
RLIT
E 5p
lus Cement-based screeds, calcium sulphate-based or
heated screeds, self-levelling products, concrete, old ceramic tile, marble slabs, stone
Page 46
Wood, PVC, rubber, linoleum, metal, resin Page 47
Exteriors
Upon condition that surfaces are sheltered (e.g. loggias, covered balconies, etc.) and made totally impervious. The use of sizes that are not larger than 50x50 cm is recommended. KE
RLIT
E 3p
lus
KERL
ITE
5plu
s
Cement-based screeds, calcium sulphate-based or heated screeds, self-levelling products, concrete, old ceramic tile, marble slabs, stone
Page 46
Wood, PVC, rubber, linoleum, metal, resin Page 47
As a general rule that applies for all building materials to be secured in place with adhesive, there is no universal adhesive for installing KERLITE on all kinds of surface.Since it is not possible to describe all possible cases, we have provided information about the most common situations. First of all, we have divided installation cases into "walls" and "floors" and then into "interior" and "exterior". Depending on the rated stress, on any work to be performed subsequently and on the maximum dimension of the slab, we have assigned a certain type of KERLITE to each category. Starting from this classification, we have thus examined the most common kinds of supporting material. The resulting chart has been sent to all main manufacturers of adhesives that have, in turn, provided the most suitable product for each category.Please note that all solutions suggested have been submitted by adhesive manufacturers, who guarantee the indications given. For ex-planations or more information, contact the respect manufacturers (see “9 - Useful contacts”).
It is essential to follow all instructions given by adhesive manufacturers. This applies in particular to waiting time running before a surface can be walked on or grouted and the "Ready to use" time shown in the following tables.
( ) Products with special finishes can have limitations depending on their area of application. Refer to specific collection catalogues.
Nadzorujący montażysta musi zbadać warunki w miejscu pracy tak aby wybrać pomiędzy klejeniem szybkim a normalnym
Pod kierownictwem
montażystyProducent Rozmiar płyt
(cm)Produkt
(*)
Podkład, jeżeli wymagany
(*)
Proporcje mieszania
(**)Klasa
(*)
nomi-nalne
zużycie(*)
ustawienia dla natężenia ruchu piesze-
go (***)
gotowy do użycia
(***)
montaż (*)
Lista producentów klejów
W zależności od kleju zalecanego przez producenta , znajdziesz rozmiar płyt w cm .
Lista klejów zalecanych przez producenta na podstawie zamierzonego zastosowania i wielkości płyty
Lista podkładów do zastosowania przed naniesieniu kleju , jak wskazano przez producenta do każdego zamierzonego użycia.
Stosunek mieszania odnosi się do pojedynczej jednostki produktu w celu uzyskania właściwości wykazanych przez producentów.
Klasa kleju w ramach normy UNI EN 12004 jest wskazane ( patrz karta poniżej “ O klejów “ )
Znajdziesz informację , ile metrów kwadratowych można zainstalować z jednej jednostki produktu wytworzonego z ustalonym stosunku mieszania.
Znajdziesz czas , który musi upłynąć , zanim idąc na powierzchni do wypełnienia spoin zaprawą
Znajdziesz czas , który musi upłynąć , zanim za pomocą głosu , tj. zanim go przedmiotem stresu statycznej i / lub dynamicznej
Znajdziesz sposób instalacji i cechy kielnią do wykorzystania dla każdego kleju .
Jak czytać załącznik?
kleje
Klasa kleju w ramach normy UNI EN 12004 (patrz karta poniżej “ O klejach “ )
Ile metrów kwadratowych można zamontować z jednej jednostki produktu wytworzonego z ustalonego stosunku mieszania.
Czas, który musi upłynąć , zanim będzie można chodzić po powierzchni w celu wypełnienia spoin zaprawą.
Czas, który musi upłynąć , zanim będzie można używać podłogi, tj. zanim na powierzchnie będą działać siły statyczne i / lub dynamiczne
Sposób montażu i rodzaj kielni do użycia z różnymi rodzajami klejów.
Kleje są podzielone na trzy klasy, w zależności od ich składu, jak ustalono w normie unI En 12004:
Cementowe (C): mieszanina hydraulicznych środków wiążących, kruszyw i dodatków organicznych (uwaga: do mieszania z wodą lub innym ciekłym dodatkiem bezpośrednio przed użyciem)
Reaktywne (R): mieszanina żywic syntetycznych, wypełniaczy mineralnych i dodatków organicznych, która twardnieje na skutek reakcji chemicznej (uwaga: te kleje mogą mieć jeden lub więcej składników)
Dyspersyjne (D): mieszanina organicznych środków wiążących, a mianowicie polimery w wodnej dyspersji, dodatki organiczne oraz wypełniacze mineralne (uwaga: mieszaniny gotowe do użycia)
w zależności od ich funkcji, kleje są klasyfikowane w ten sposób:
Klasa 1: normalne warunki
Klasa 2: ulepszone warunki
Istnieją trzy klasy dodatkowe:
Klasa f: kleje szybkoschnące
Klasa T: kleje antypoślizgowe
Klasa E: kleje o wydłużonym czasie schnięcia
Jest czwarta dodatkowa klasa tylko dla kleji cementowych: kleje mogą być klasyfikowane jako odkształcalne (S) i dzieli się je na podstawie wyników badań w ramach normy unI En 12002:
Klasa S1: kleje odkształcalne
Klasa S2: kleje wysoko-odkształcalne
38 3938 39
KERLITE Cotto d’Este > KERLITE Technical Manual
Supporting material: concrete, old ceramic tile, marble, stone
A.1b - Wall installation in interiors of KERLITE 3mm
(*) Instructions provided directly by manufacturers, who guarantee the information given. For explanations or more details, contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”)”.
(**) Instructions provided directly by manufacturers, who guarantee the information given. If a product is offered in both "white" and a "grey" versions, the mixing ratio may vary. For explanations or more details, contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”)”.
(***) Ratings provided directly by manufacturers, who guarantee the information given, are based on laboratory tests performed at 23° C and with a relative humidity of 50%. In the event of use in different situations or for explanations or more details, contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”)”.
Supporting material: two-coat plaster, gypsum plaster, plasterboard, fibre cement panels.
At the discretion
of I.S.
Manufac-turer
Size of slabs(cm)
Product(*)
Primer, if necessary(*) Mixing ratio (**) Class
(*)
Nominalcover-age (*)
Workability (***)
Ready for use(***)
Installation(*)
For situations in which a
normal setting adhesives is
recommended
MAPEI
50x50; 100x40; 100x50
KERAFLEX MAXI S1
Compulsory for gypsum-based, anhydride
or absorbent surfaces:Primer G or
ECOPRIM T
1 bag (25 kg)+ 7,2/7,7 litres of
waterC2 TE S1
7 m2
8 hours 14 days
Installation with a double layer of adhesive
ULTRALITE S11 bag (15 kg)
+ 8,4/8,7 litres of water
C2 TE S1
100x100; 300x100
ULTRALITE S21 bag (15 kg)
+ 5,9/6,2 litres of water
C2 E S2 6,3 m2
KERABOND + ISOLASTIC
1 bag (25 kg)+ 8,5 kg of ISOLASTIC C2 E S2 6,5 m2
KERAKOLL All sizes H40 NO LIMITS For gypsum-based surfaces: Primer A Eco
Grey 1 bag (25 kg)from 7,1 to 8,8 litres of water
C2 TE S1 6 m2 20 hours 3 daysWhite 1 bag (25 kg) from 7,2 to
9,5 litres of water
LATICRETE All sizes LATICRETE 254 Platinum
Not necessary, according to manufacturer
1 bag (25 kg) + 6 litres of water C2 TE S1 5 m2 1 day 14 days
LITOKOL All sizes SUPERFLEX K77 For gypsum-based surfaces: Primer C
1 bag (25 kg) + 8,5 litres of water C2 TE S1 6 m2 8 hours 14 days
PCI - BASF All sizes PCI NANOLIGHT For gypsum-based surfaces: PCI GISOGRUND
1 bag (15 kg) + 9 litres of water C2 TE S1 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBERAll sizes
WEBER.COL PRO HP For gypsum-based
surfaces: WEBER.PRIM PF15
1 bag (25 kg) + 7 litres of water C2 TE S1
5 m2
8 hours
14 daysWEBER.COL PRO
HF LIGHT1 bag (15 kg) + 8
litres of water C2 TE S2 1 day
ARDEX All sizes ARDEX X 77 Microtec
For gypsum-based surfaces: ARDEX P 51
1 bag (25 kg) + 11 litres of water
C2 T(T)E(E) S1 10 m2 8 hours 1 day Installation with a single-layer
of adhesive (6 mm trowel)
For situations in which a
quick setting adhesive is
recommended
MAPEI
50x50; 100x40; 100x50
GRANIRAPID
COMPULSORY for gypsum-based, anhydride
or absorbent surfaces:
Primer G orECOPRIM T
Component A: 1 bag (25 kg)
Component B: tub (5,5 kg)
C2 F S1
6 m2
3 hours 1 day
Installation with a double layer of adhesive
ULTRALITE S1 QUICK 1 bag (15 kg) +
5,1/5,7 litres of water
C2 FTE S1
100x100; 300x100
ULTRALITE S2 QUICK C2 FE S2 7 m2
ELASTORAPID
Component A: 1 bag (25 kg)
Component B: tub (6,5 kg)
C2 FTE S2 6 m2
KERAKOLL All sizes H40 ECO RAPIDFLEX
For gypsum-based surfaces: Primer A Eco
1 bag (25 kg) + 6,3 litres of water
C2F TE S1 6 m2 3 hours 2 days
LATICRETE All sizes
LATICRETE 335 Rapid Super Flex + LATICRETE 282
Latex Additive
Not necessary, according to manufacturer
1 bag (25 kg)+ 6/7 litres of latex C2 TE F 5 m2 6 hours 2 days
LITOKOL All sizesLITOSTONE K99 + LATEXKOL +
water
For gypsum-based surfaces: Primer C
1 bag (25 kg) + 3,5 litres of
LATEXKOL + 3,5 litres of water
C2 FE S1 5 m2 4 hours 1 day
PCI - BASF All sizes PCI NANOLIGHT For gypsum-based surfaces: PCI GISOGRUND
1 bag (15 kg) + 9 litres of water C2 TE S1 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBERAll sizes
WEBER.COL PRO MARMO + WEBER
L50 For gypsum-based surfaces: WEBER.PRIM PF15
1 bag (25 kg)+ 7 litres of WEBER L50 C2 FT
S1 5 m2 4 hours 3 daysWEBER.COL PRO RAPID + WEBER
L50
1 bag (25 kg)+ 6-6,5 litres of
WEBER L50
ARDEX All sizes ARDEX X 77 S microtec
For gypsum-based surfaces: ARDEX P 51
1 bag (25 kg) + 8,5 litres of water
C2 FT(T)E S1 10 m2 90 min. 6 hours
Installation with a single layer of adhesive (6 mm
trowel)
(*) Instructions provided directly by manufacturers, who guarantee the information given. For explanations or more details, contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”)”.
(**) Instructions provided directly by manufacturers, who guarantee the information given. If a product is offered in both "white" and a "grey" versions, the mixing ratio may vary. For explanations or more details, contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”)”.
(***) Ratings provided directly by manufacturers, who guarantee the information given, are based on laboratory tests performed at 23° C and with a relative humidity of 50%. In the event of use in different situations or for explanations or more details, contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”)”.
A.1a - Wall installation in interiors of KERLITE 3mm
At the discretion of
I.S.
Manufac-turer
Size of slabs(cm)
Product(*)
Primer, if necessary(*) Mixing ratio (**) Class
(*)
Nominalcover-age (*)
Workability (***)
Ready for use(***)
Installation(*)
For situations in which a
normal setting adhesives is
recommended
MAPEI
50x50; 100x40; 100x50
KERAFLEX MAXI S1
If levelling is necessary, on the above mentioned
supports, apply the following product
beforehand ECOPRIM GRIP
1 bag (25 kg) + 7,2/7,7 litres of
waterC2 TE S1
7 m2
8 hours 14 days
Installation with a double layer of adhesive
ULTRALITE S11 bag (15 kg) + 8,4/8,7 litres of
waterC2 TE S1
100x100; 300x100
ULTRALITE S21 bag (15 kg) + 5,9/6,2 litres of
waterC2 E S2 6,3 m2
KERABOND + ISOLASTIC
1 bag (25 kg) + 8,5 kg of ISOLASTIC
C2 E S2 6,5 m2
KERAKOLL All sizes H40 NO LIMITS Not necessary, according to manufacturer
Grey 1 bag (25 kg) from 7,1 to
8,8 litres of waterC2 TE S1 6 m2 20 hours 3 days
White 1 bag (25 kg) from 7,2 to
9,5 litres of water
LATICRETE All sizes LATICRETE 254 Platinum
Not necessary, according to manufacturer
1 bag (25 kg) + 6 litres of water C2 TE S1 5 m2 1 day 7 days
LITOKOL All sizes SUPERFLEX K77 Not necessary, according to manufacturer
1 bag (25 kg) + 8,5 litres of water C2 TE S1 6 m2 8 hours 7 days
PCI - BASF All sizes PCI NANOLIGHT On non-absorbent supportsPCI GISOGRUND 303
1 bag (15 kg) + 9 litres of water C2 TE S1 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBER
50x50; 100x40; 100x50
WEBER.COL PRO HP For old ceramic tile, marble
slabs and stone:WEBER. FLOOR 4716 Prime
1 bag (25 kg) + 7 litres of water C2 TE S1
5 m2 8 hours 14 days100x100; 300x100
WEBER.COL PRO HP + WEBER L50
1 bag (15 kg) + 7 litres of WEBER
L50C2 TE S2
ARDEX All sizes ARDEX X 77 Microtec
As an alternative for old ceramic tile, marble slabs
and stone:- ARDEX P 4 - ARDEX X 77
(rough levelled)
1 bag (25 kg) + 11 litres of water
C2 T(T)E(E) S1 10 m2 8 hours 1 day
Installation with a single layer of adhesive (6 mm
trowel)
For situations in which a
quick setting adhesive is
recommended
MAPEI
50x50; 100x40; 100x50
GRANIRAPID
If levelling is necessary, on the above mentioned
supports, apply the following product
beforehand ECOPRIM GRIP
Component A: 1 bag (25 kg)
Component B: tub (5,5 kg)
C2 F S16 m2
3 hours 1 day
Installation with a double layer of adhesive
ULTRALITE S1 QUICK 1 bag (15 kg) +
5,1/5,7 litres of water
C2 FTE S1
100x100; 300x100
ULTRALITE S2 QUICK C2 FE S2 7 m2
ELASTORAPID
Component A: 1 bag (25 kg)
Component B: tub (6,5 kg)
C2 FTE S2 6 m2
KERAKOLL All sizes H40 ECO RAPIDFLEX
Not necessary, according to manufacturer
1 bag (25 kg) + 6,3 litres of water
C2F TE S1 6 m2 3 hours 2 days
LATICRETE All sizes
LATICRETE 335 Rapid Super Flex + LATICRETE 282
Latex Additive
Not necessary, according to manufacturer
1 bag (25 kg) + 6/7 litres of latex C2 TE F 5 m2 6 hours 2 days
LITOKOL All sizesLITOSTONE K99 + LATEXKOL +
water
For gypsum-based surfaces: Primer C
1 bag (25 kg) + 3,5 litres of
LATEXKOL + 3,5 litres of water
C2 FE S1 5 m2 4 hours 1 day
PCI - BASF All sizes PCI NANOLIGHTOn non-absorbent
supportsPCI GISOGRUND 303
1 bag (15 kg) + 9 litres of water C2 TE S1 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBERAll sizes
WEBER.COL PRO MARMO + WEBER
L50 For old ceramic tile, marble slabs and stone:
WEBER. FLOOR 4716 Prime
1 bag (25 kg)+ 7 litres of WEBER L50
C2 FT S1 5 m2 4 hours 3 days
WEBER.COL PRO RAPID + WEBER
L50
1 bag (25 kg)+ 6-6,5 litres of
WEBER L50
ARDEX All sizes ARDEX X 77 S microtec
As an alternative for old ceramic tile, marble slabs
and stone:- ARDEX P 4 - ARDEX X 77
(rough levelled)
1 bag (25 kg) + 8,5 litres of water
C2 FT(T)E S1 10 m2 90 min. 6 hours
Installation with a single layer of adhesive (6 mm
trowel)
Odpowiedzial-ność instalatora
w sytuacjach kiedy normalne
kleje są polecane
Producent Produkt(*)Rozmiar płyt (cm) Podkład, jeśli konieczny
Niezbędne przy gipsowych, anhydrytowych lub
chłonnych powierzchniach:
Primer G lub ECOPRIM T
Dla gipsowych powier-zchni: Primer A Eco
Nie konieczne, według zaleceń producenta
Dla gipsowych powierzchni: Primer A Eco
Dla gipsowych powierzchni: Primer A Eco
Dla gipsowych powierzchni: Primer C
Dla gipsowych powierzchni: PCI GISOGRUND
Dla gipsowych powierzchni: WEBER.PRIM PF15
Dla gipsowych powierzchni: ARDEX P 51
Proporcje mieszania (**)
Klasa (*)
nominalne pokrycie
(*)
możliwość obróbki
(***)
gotowe do użycia (***)
montaż (*)
Instrukcje podane bezpośrednio przez producentów, którzy gwarantują poprawność informacji. Po więcej szczegółów, skontaktuj się ze wsparciem technicznym odpowiednich producentów (zobacz “9 - Przydatne kontakty”) “.
Instrukcje podane bezpośrednio przez producentów, którzy gwarantują poprawność informacji. Jeśli produkt jest oferowany zarówno w wersjach “biały” i “szary” , proporcje mieszania mogą się różnić. Po więcej szczegółów, skontaktuj się ze wsparciem technicznym odpowiednich producentów (zobacz “9 - Przydatne kontakty”) “.
Instrukcje podane bezpośrednio przez producentów, którzy gwarantują poprawność informacji. Na podstawie badań laboratoryjnych przeprowadzonych w temperaturze 23 ° C i przy wilgotności względnej 50%. W przypadku zastosowania w innych sytuacjach lub w celu uzyskania więcej szczegółów, skontaktuj się ze wsparciem technicznym odpowiednich producentów (zobacz “9 - Przydatne kontakty”) “.
a.1a - KERLITE 3mm - montaż na ścianie we wnętrzach
materiał podłoża: podwójna warstwa tynku, tynk gipsowy, płyta gipsowa, panele włokienno-cementowe
Niezbędne przy gipsowych, anhydrytowych lub
chłonnych powierzchniach:
Primer G lub ECOPRIM T
Nie konieczne, według zaleceń producenta
Dla gipsowych powierzchni: PCI GISOGRUND
Dla gipsowych powierzchni: WEBER.PRIM PF15
Dla gipsowych powierzchni: ARDEX P 51
1 paczka (25 kg) + 8,5 litra wody
1 paczka (25 kg) + 6-6,5 litra
WEBER L50
1 paczka (25 kg) + 7 litrów
WEBER L50
1 paczka (15 kg) + 9 litrów wody
1 paczka (25 kg) + 3,5 litra LATEXKOL
+ 3,5 litra wody
1 paczka (25 kg) + 6/7 litrów latexu
1 paczka (25 kg) + 6,3 litra wody
1 paczka (15 kg) + 5,1/5,7 litra wody
1 paczka (25 kg) + 11 litrów wody
1 paczka (25 kg) + 8 litrów wody
1 paczka (25 kg) + 7 litrów wody
1 paczka (25 kg) + 9 litrów wody
1 paczka (25 kg) + 8,5 litra wody
1 paczka (25 kg) + 6 litrów wody
1 biała paczka (25 kg) 7,2 - 9,5 litra
wody
1 szara paczka (25 kg) 7,1 - 8,8 litra
wody
1 paczka (15 kg) + 5,9/6,2 litra wody
1 paczka (15 kg) + 8,4/8,7 litra wody
1 paczka (25 kg) + 7,2/7,7 litra wody
8 godzin
20 godzin
1 dzień
1 dzień
1 dzień
1 dzień
1 dzień
1 dzień
2 dni
2 dni
3 dni
6 godzin
4 godziny
3 godziny
3 godziny
90 min
4 godziny
6 godzin
8 godzin
3 dni Montaż z podwójną warstwą kleju
Montaż z podwójną warstwą kleju
Montaż z pojedyńczą warstwą kleju (kielnia 6 mm)
Montaż z pojedyńczą warstwą kleju (kielnia 6 mm)
14 dni
14 dni
14 dni
14 dni1 dzień
8 godzin
8 godzin
8 godzin
8 godzin
1 paczka (25 kg) + 8,5 kg ISOLASTIC
Komponent A: 1 paczka (25 kg)
Komponent B: opa-kowanie (6,5 kg)
Komponent A: 1 paczka (25 kg)
Komponent B: opa-kowanie (5,5 kg)
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
w sytuacjach kiedy szybkow-iążące kleje są
polecane
38 3938 39
KERLITE Cotto d’Este > KERLITE Technical Manual
Supporting material: concrete, old ceramic tile, marble, stone
A.1b - Wall installation in interiors of KERLITE 3mm
(*) Instructions provided directly by manufacturers, who guarantee the information given. For explanations or more details, contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”)”.
(**) Instructions provided directly by manufacturers, who guarantee the information given. If a product is offered in both "white" and a "grey" versions, the mixing ratio may vary. For explanations or more details, contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”)”.
(***) Ratings provided directly by manufacturers, who guarantee the information given, are based on laboratory tests performed at 23° C and with a relative humidity of 50%. In the event of use in different situations or for explanations or more details, contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”)”.
Supporting material: two-coat plaster, gypsum plaster, plasterboard, fibre cement panels.
At the discretion
of I.S.
Manufac-turer
Size of slabs(cm)
Product(*)
Primer, if necessary(*) Mixing ratio (**) Class
(*)
Nominalcover-age (*)
Workability (***)
Ready for use(***)
Installation(*)
For situations in which a
normal setting adhesives is
recommended
MAPEI
50x50; 100x40; 100x50
KERAFLEX MAXI S1
Compulsory for gypsum-based, anhydride
or absorbent surfaces:Primer G or
ECOPRIM T
1 bag (25 kg)+ 7,2/7,7 litres of
waterC2 TE S1
7 m2
8 hours 14 days
Installation with a double layer of adhesive
ULTRALITE S11 bag (15 kg)
+ 8,4/8,7 litres of water
C2 TE S1
100x100; 300x100
ULTRALITE S21 bag (15 kg)
+ 5,9/6,2 litres of water
C2 E S2 6,3 m2
KERABOND + ISOLASTIC
1 bag (25 kg)+ 8,5 kg of ISOLASTIC C2 E S2 6,5 m2
KERAKOLL All sizes H40 NO LIMITS For gypsum-based surfaces: Primer A Eco
Grey 1 bag (25 kg)from 7,1 to 8,8 litres of water
C2 TE S1 6 m2 20 hours 3 daysWhite 1 bag (25 kg) from 7,2 to
9,5 litres of water
LATICRETE All sizes LATICRETE 254 Platinum
Not necessary, according to manufacturer
1 bag (25 kg) + 6 litres of water C2 TE S1 5 m2 1 day 14 days
LITOKOL All sizes SUPERFLEX K77 For gypsum-based surfaces: Primer C
1 bag (25 kg) + 8,5 litres of water C2 TE S1 6 m2 8 hours 14 days
PCI - BASF All sizes PCI NANOLIGHT For gypsum-based surfaces: PCI GISOGRUND
1 bag (15 kg) + 9 litres of water C2 TE S1 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBERAll sizes
WEBER.COL PRO HP For gypsum-based
surfaces: WEBER.PRIM PF15
1 bag (25 kg) + 7 litres of water C2 TE S1
5 m2
8 hours
14 daysWEBER.COL PRO
HF LIGHT1 bag (15 kg) + 8
litres of water C2 TE S2 1 day
ARDEX All sizes ARDEX X 77 Microtec
For gypsum-based surfaces: ARDEX P 51
1 bag (25 kg) + 11 litres of water
C2 T(T)E(E) S1 10 m2 8 hours 1 day Installation with a single-layer
of adhesive (6 mm trowel)
For situations in which a
quick setting adhesive is
recommended
MAPEI
50x50; 100x40; 100x50
GRANIRAPID
COMPULSORY for gypsum-based, anhydride
or absorbent surfaces:
Primer G orECOPRIM T
Component A: 1 bag (25 kg)
Component B: tub (5,5 kg)
C2 F S1
6 m2
3 hours 1 day
Installation with a double layer of adhesive
ULTRALITE S1 QUICK 1 bag (15 kg) +
5,1/5,7 litres of water
C2 FTE S1
100x100; 300x100
ULTRALITE S2 QUICK C2 FE S2 7 m2
ELASTORAPID
Component A: 1 bag (25 kg)
Component B: tub (6,5 kg)
C2 FTE S2 6 m2
KERAKOLL All sizes H40 ECO RAPIDFLEX
For gypsum-based surfaces: Primer A Eco
1 bag (25 kg) + 6,3 litres of water
C2F TE S1 6 m2 3 hours 2 days
LATICRETE All sizes
LATICRETE 335 Rapid Super Flex + LATICRETE 282
Latex Additive
Not necessary, according to manufacturer
1 bag (25 kg)+ 6/7 litres of latex C2 TE F 5 m2 6 hours 2 days
LITOKOL All sizesLITOSTONE K99 + LATEXKOL +
water
For gypsum-based surfaces: Primer C
1 bag (25 kg) + 3,5 litres of
LATEXKOL + 3,5 litres of water
C2 FE S1 5 m2 4 hours 1 day
PCI - BASF All sizes PCI NANOLIGHT For gypsum-based surfaces: PCI GISOGRUND
1 bag (15 kg) + 9 litres of water C2 TE S1 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBERAll sizes
WEBER.COL PRO MARMO + WEBER
L50 For gypsum-based surfaces: WEBER.PRIM PF15
1 bag (25 kg)+ 7 litres of WEBER L50 C2 FT
S1 5 m2 4 hours 3 daysWEBER.COL PRO RAPID + WEBER
L50
1 bag (25 kg)+ 6-6,5 litres of
WEBER L50
ARDEX All sizes ARDEX X 77 S microtec
For gypsum-based surfaces: ARDEX P 51
1 bag (25 kg) + 8,5 litres of water
C2 FT(T)E S1 10 m2 90 min. 6 hours
Installation with a single layer of adhesive (6 mm
trowel)
(*) Instructions provided directly by manufacturers, who guarantee the information given. For explanations or more details, contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”)”.
(**) Instructions provided directly by manufacturers, who guarantee the information given. If a product is offered in both "white" and a "grey" versions, the mixing ratio may vary. For explanations or more details, contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”)”.
(***) Ratings provided directly by manufacturers, who guarantee the information given, are based on laboratory tests performed at 23° C and with a relative humidity of 50%. In the event of use in different situations or for explanations or more details, contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”)”.
A.1a - Wall installation in interiors of KERLITE 3mm
At the discretion of
I.S.
Manufac-turer
Size of slabs(cm)
Product(*)
Primer, if necessary(*) Mixing ratio (**) Class
(*)
Nominalcover-age (*)
Workability (***)
Ready for use(***)
Installation(*)
For situations in which a
normal setting adhesives is
recommended
MAPEI
50x50; 100x40; 100x50
KERAFLEX MAXI S1
If levelling is necessary, on the above mentioned
supports, apply the following product
beforehand ECOPRIM GRIP
1 bag (25 kg) + 7,2/7,7 litres of
waterC2 TE S1
7 m2
8 hours 14 days
Installation with a double layer of adhesive
ULTRALITE S11 bag (15 kg) + 8,4/8,7 litres of
waterC2 TE S1
100x100; 300x100
ULTRALITE S21 bag (15 kg) + 5,9/6,2 litres of
waterC2 E S2 6,3 m2
KERABOND + ISOLASTIC
1 bag (25 kg) + 8,5 kg of ISOLASTIC
C2 E S2 6,5 m2
KERAKOLL All sizes H40 NO LIMITS Not necessary, according to manufacturer
Grey 1 bag (25 kg) from 7,1 to
8,8 litres of waterC2 TE S1 6 m2 20 hours 3 days
White 1 bag (25 kg) from 7,2 to
9,5 litres of water
LATICRETE All sizes LATICRETE 254 Platinum
Not necessary, according to manufacturer
1 bag (25 kg) + 6 litres of water C2 TE S1 5 m2 1 day 7 days
LITOKOL All sizes SUPERFLEX K77 Not necessary, according to manufacturer
1 bag (25 kg) + 8,5 litres of water C2 TE S1 6 m2 8 hours 7 days
PCI - BASF All sizes PCI NANOLIGHT On non-absorbent supportsPCI GISOGRUND 303
1 bag (15 kg) + 9 litres of water C2 TE S1 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBER
50x50; 100x40; 100x50
WEBER.COL PRO HP For old ceramic tile, marble
slabs and stone:WEBER. FLOOR 4716 Prime
1 bag (25 kg) + 7 litres of water C2 TE S1
5 m2 8 hours 14 days100x100; 300x100
WEBER.COL PRO HP + WEBER L50
1 bag (15 kg) + 7 litres of WEBER
L50C2 TE S2
ARDEX All sizes ARDEX X 77 Microtec
As an alternative for old ceramic tile, marble slabs
and stone:- ARDEX P 4 - ARDEX X 77
(rough levelled)
1 bag (25 kg) + 11 litres of water
C2 T(T)E(E) S1 10 m2 8 hours 1 day
Installation with a single layer of adhesive (6 mm
trowel)
For situations in which a
quick setting adhesive is
recommended
MAPEI
50x50; 100x40; 100x50
GRANIRAPID
If levelling is necessary, on the above mentioned
supports, apply the following product
beforehand ECOPRIM GRIP
Component A: 1 bag (25 kg)
Component B: tub (5,5 kg)
C2 F S16 m2
3 hours 1 day
Installation with a double layer of adhesive
ULTRALITE S1 QUICK 1 bag (15 kg) +
5,1/5,7 litres of water
C2 FTE S1
100x100; 300x100
ULTRALITE S2 QUICK C2 FE S2 7 m2
ELASTORAPID
Component A: 1 bag (25 kg)
Component B: tub (6,5 kg)
C2 FTE S2 6 m2
KERAKOLL All sizes H40 ECO RAPIDFLEX
Not necessary, according to manufacturer
1 bag (25 kg) + 6,3 litres of water
C2F TE S1 6 m2 3 hours 2 days
LATICRETE All sizes
LATICRETE 335 Rapid Super Flex + LATICRETE 282
Latex Additive
Not necessary, according to manufacturer
1 bag (25 kg) + 6/7 litres of latex C2 TE F 5 m2 6 hours 2 days
LITOKOL All sizesLITOSTONE K99 + LATEXKOL +
water
For gypsum-based surfaces: Primer C
1 bag (25 kg) + 3,5 litres of
LATEXKOL + 3,5 litres of water
C2 FE S1 5 m2 4 hours 1 day
PCI - BASF All sizes PCI NANOLIGHTOn non-absorbent
supportsPCI GISOGRUND 303
1 bag (15 kg) + 9 litres of water C2 TE S1 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBERAll sizes
WEBER.COL PRO MARMO + WEBER
L50 For old ceramic tile, marble slabs and stone:
WEBER. FLOOR 4716 Prime
1 bag (25 kg)+ 7 litres of WEBER L50
C2 FT S1 5 m2 4 hours 3 days
WEBER.COL PRO RAPID + WEBER
L50
1 bag (25 kg)+ 6-6,5 litres of
WEBER L50
ARDEX All sizes ARDEX X 77 S microtec
As an alternative for old ceramic tile, marble slabs
and stone:- ARDEX P 4 - ARDEX X 77
(rough levelled)
1 bag (25 kg) + 8,5 litres of water
C2 FT(T)E S1 10 m2 90 min. 6 hours
Installation with a single layer of adhesive (6 mm
trowel)
Odpowiedzial-ność instalatora
w sytuacjach kiedy normalne
kleje są polecane
Producent Produkt(*)Rozmiar płyt (cm) Podkład, jeśli konieczny
Jeżeli poziomowanie jest konieczne, na wymieni-
onych podkładach, zaap-likuj następujący produkt
wcześniej
ECOPRIM GRIP
Jeżeli poziomowanie jest konieczne, na wymieni-
onych podkładach, zaap-likuj następujący produkt
wcześniej
ECOPRIM GRIP
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Dla starych płytek ceramic-znych, marmurów i kamieni
naturalnych: WEBER. FLOOR 4716 Prime
Dla starych płytek ceramic-znych, marmurów i kamieni
naturalnych: WEBER. FLOOR 4716 Prime
Dla gipsowych powierzchni: Primer C
Dla niechłonnych powier-zchni: PCI GISOGRUND 303
Dla niechłonnych powier-zchni: PCI GISOGRUND 303
Jako alternatywa dla starych płytek ceramicznych, mar-
murów i kamieni naturalnych: - ARDEX p 4 - ARDEX X77
(wstępnie wypoziomowanie)
Jako alternatywa dla starych płytek ceramicznych, mar-
murów i kamieni naturalnych: - ARDEX p 4 - ARDEX X77
(wstępnie wypoziomowanie)
Proporcje mieszania (**)
Klasa (*)
nominalne pokrycie
(*)
możliwość obróbki
(***)
gotowe do użycia (***)
montaż (*)
Instrukcje podane bezpośrednio przez producentów, którzy gwarantują poprawność informacji. Po więcej szczegółów, skontaktuj się ze wsparciem technicznym odpowiednich producentów (zobacz “9 - Przydatne kontakty”) “.
Instrukcje podane bezpośrednio przez producentów, którzy gwarantują poprawność informacji. Jeśli produkt jest oferowany zarówno w wersjach “biały” i “szary” , proporcje mieszania mogą się różnić. Po więcej szczegółów, skontaktuj się ze wsparciem technicznym odpowiednich producentów (zobacz “9 - Przydatne kontakty”) “.
Instrukcje podane bezpośrednio przez producentów, którzy gwarantują poprawność informacji. Na podstawie badań laboratoryjnych przeprowadzonych w temperaturze 23 ° C i przy wilgotności względnej 50%. W przypadku zastosowania w innych sytuacjach lub w celu uzyskania więcej szczegółów, skontaktuj się ze wsparciem technicznym odpowiednich producentów (zobacz “9 - Przydatne kontakty”) “.
materiał podłoża: beton, stare płytki ceramiczne, marmur, kamień naturalny
a.1b - KERLITE 3mm - montaż na ścianie we wnętrzach
1 paczka (25 kg) + 8,5 litra wody
1 paczka (25 kg) + 6-6,5 litra
WEBER L50
1 paczka (25 kg) + 7 litrów
WEBER L50
1 paczka (15 kg) + 9 litrów wody
1 paczka (25 kg) + 3,5 litra LATEXKOL
+ 3,5 litra wody
1 paczka (25 kg) + 6/7 litrów latexu
1 paczka (25 kg) + 6,3 litra wody
1 paczka (15 kg) + 5,1/5,7 litra wody
1 paczka (25 kg) + 11 litrów wody
1 paczka (25 kg) + 7 litrów wody
1 paczka (15 kg) + 7 litrów WEBER L50
1 paczka (15 kg) + 9 litrów wody
1 paczka (25 kg) + 8,5 litra wody
1 paczka (25 kg) + 6 litrów wody
1 biała paczka (25 kg) 7,2 - 9,5 litra
wody
1 szara paczka (25 kg) 7,1 - 8,8 litra
wody
1 paczka (15 kg) + 5,9/6,2 litra wody
1 paczka (15 kg) + 8,4/8,7 litra wody
1 paczka (25 kg) + 7,2/7,7 litra wody
8 godzin
20 godzin
1 dzień
1 dzień
1 dzień
1 dzień
1 dzień
1 dzień
2 dni
2 dni
3 dni
6 godzin
4 godziny
4 godziny
3 godziny
3 godziny
90 min
6 godzin
8 godzin
3 dniMontaż z podwójną
warstwą kleju
Montaż z podwójną warstwą kleju
Montaż z pojedyńczą warstwą kleju (kielnia 6 mm)
Montaż z pojedyńczą warstwą kleju (kielnia 6 mm)
14 dni
7 dni
7 dni
14 dni
8 godzin
8 godzin
8 godzin
8 godzin8 godzin
1 paczka (25 kg) + 8,5 kg ISOLASTIC
Komponent A: 1 paczka (25 kg)
Komponent B: opa-kowanie (6,5 kg)
Komponent A: 1 paczka (25 kg)
Komponent B: opa-kowanie (5,5 kg)
Wszystkie rozmiary
Wszystkie rozmiaryWszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
w sytuacjach kiedy szybkow-iążące kleje są
polecane
40 4140 41
KERLITE Cotto d’Este > KERLITE Technical Manual
Supporting material: two-coat plaster, gypsum plaster, plasterboard, fibre cement panels
A.2a - Wall installation in interiors of KERLITE 3plus and KERLITE 5plus
At the discretion
of I.S.
Manufac-turer
Size of slabs(cm)
Product(*)
Primer, if necessary(*) Mixing ratio (**) Class
(*)
Nominal cover-age (*)
Workability (***)
Ready for use(***)
Installation(*)
For situations in which a
normal setting adhesives is
recommended
MAPEI
50x50; 100x40; 100x50
KERAFLEX MAXI S1 COMPULSORY for gypsum-based, anhydride
or absorbent surfaces:
Primer G or ECOPRIM T
1 bag (25 kg) + 7,2/7,7 litres of water C2 TE S1
7 m2
8 hours 14 days
Installation with a double layer of adhesive
ULTRALITE S1 1 bag (15 kg) + 8,4/8,7 litres of water C2 TE S1
100x100; 300x100ULTRALITE S2 1 bag (15 kg) +
5,9/6,2 litres of water C2 E S2 6,3 m2
KERABOND + ISOLASTIC
1 bag (25 kg) + 8,5 kg of ISOLASTIC C2 E S2 6,5 m2
KERAKOLL All sizes H40 NO LIMITS For gypsum-based surfaces: Primer A Eco
Grey 1 bag (25 kg) from 7,1 to
8,8 litres of waterC2 TE S1 6 m2 20 hours 3 days
White 1 bag (25 kg) from 7,2 to
9,5 litres of water
LATICRETE All sizes LATICRETE 254 Platinum
Not necessary, according to manufacturer
1 bag (25 kg) + 6 litres of water C2 TE S1 5 m2 1 day 7 days
LITOKOL
50x50;100x40; 100x50 SUPERFLEX K77
For gypsum-based surfaces: Primer C
1 bag (25 kg) + 8,5 litres of water C2 TE S1 6 m2
8 hours 7 days100x100; 300x100
CEMENTKOL K21 + LATEXKOL
1 bag (25 kg) + 7,5 kg of LATEXKOL C2 S2 5 m2
PCI - BASF All sizes PCI NANOLIGHT + PCI LASTOFLEX
For gypsum-based surfaces: PCI GISOGRUND
1 bag (15 kg) + 1 can of PCI LASTOFLEX (4 kg) + 5 litres of water
C2 TE S2 5,5 m2 8 hours 1 day
SAINT-GOBAIN / WEBER All sizes
WEBER.COL PRO HP For gypsum-based surfaces:
WEBER.PRIM PF15
1 bag (25 kg) + 7 litres of water C2 TE S1
5 m2
8 hours14 days
WEBER.COL PRO HF LIGHT
1 bag (15 kg) + 8 litres of water C2 TE S2 1 day
ARDEX All sizesARDEX X 77
microtec + ARDEX E 90
For gypsum-based surfaces: ARDEX P 51
1 bag (25 kg) + 1 can of ARDEX E 90 (4,5
kg) + 9 litres of water
C2 T(T)E(E) S2 10 m2 8 hours 1 day Installation with a single layer
of adhesive (6 mm trowel)
For situations in which a
quick setting adhesive is
recommended
MAPEI
50x50; 100x40; 100x50
GRANIRAPID
COMPULSORY for gypsum-based, anhydride or absorbent
surfaces:Primer G or ECOPRIM T
Component A: 1 bag (25 kg) Component
B: tub (5,5 kg)C2 F S1
6 m2
3 hours 1 day
Installation with a double layer of adhesive
ULTRALITE S1 QUICK 1 bag (15 kg) +
5,1/5,7 litres of water
C2 FTE S1
100x100; 300x100
ULTRALITE S2 QUICK C2 FE S2 7 m2
ELASTORAPIDComponent A: 1 bag (25 kg) Component
B: tub (6,5 kg)C2 FTE S2 6 m2
KERAKOLL All sizes H40 ECO RAPIDFLEX
For gypsum-based surfaces: Primer A Eco
1 bag (25 kg) + 6,3 litres of water
C2F TE S1 6 m2 3 hours 2 days
LATICRETE All sizes
LATICRETE 335 Rapid Super Flex + LATICRETE 282
Latex Additive
Not necessary, according to manufacturer
1 bag (25 kg) + 6/7 litres of latex C2 TE F 5 m2 6 hours 2 days
LITOKOL
50x50;100x40; 100x50
LITOSTONE K99 + LATEXKOL + water For gypsum-based surfaces:
Primer C
1 bag (25 kg) + 3,5 litres of LATEXKOL +
3,5 litres of waterC2 FE S1
5 m2 4 hours 1 day
100x100; 300x100
LITOSTONE K99 + LATEXKOL
1 bag (25 kg) + 7,5 kg of LATEXKOL C2 FE S2
PCI - BASF All sizes PCI NANOLIGHT + PCI LASTOFLEX
For gypsum-based surfaces: PCI GISOGRUND
1 bag (15 kg) + 1 can of PCI LASTOFLEX (4 kg) + 5 litres of water
C2 TE S2 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBERAll sizes
WEBER.COL PRO MARMO + WEBER
L50 For old ceramic tile, marble slabs and stone:
WEBER. FLOOR 4716 Prime
1 bag (25 kg)+ 7 litres of WEBER L50
C2 FT S1 5 m2 4 hours 3 days
WEBER.COL PRO RAPID + WEBER
L50
1 bag (25 kg)+ 6-6,5 litres of
WEBER L50
ARDEX All sizesARDEX X 77 S
microtec + ARDEX E 90
For gypsum-based surfaces: ARDEX P 51
1 bag (25 kg) + 3 kg of ARDEX E 90 + 7,5
litres of water
C2 FT(T)E S2 10 m2 90 min. 6 hours Installation with a single layer
of adhesive (6 mm trowel)
(*) Instructions provided directly by manufacturers, who guarantee the information given. For explanations or more details, contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”)”.
(**) Instructions provided directly by manufacturers, who guarantee the information given. If a product is offered in both "white" and a "grey" versions, the mixing ratio may vary. For explanations or more details, contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”)”.
(***) Ratings provided directly by manufacturers, who guarantee the information given, are based on laboratory tests performed at 23° C and with a relative humidity of 50%. In the event of use in different situations or for explanations or more details, contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”)”.
Supporting material: particle board, metal
At the discretion
of I.S.
Manufac-turer
Size of slabs(cm)
Product(*)
Primer, if necessary(*) Mixing ratio (**) Class
(*)
Nominal cover-age (*)
Workability (***)
Ready for use(***)
Installation(*)
For situations in which a
normal setting adhesives is
recommended
MAPEI All sizes
KERALASTIC
Not necessary, according to manufacturer
1 can (10 kg) R2
3 m2 12 hours 7 days
Installation with a double layer of adhesive
KERALASTIC T 1 can (10 kg) R2T
KERAKOLL All sizes H40 NO LIMITS KERAGRIP ECO
Grey 1 bag (25 kg)from 7,1 to 8,8 litres of water
C2 TE S1 6 m2 20 hours 3 daysWhite 1 bag (25 kg) from 7,2 to
9,5 litres of water
LATICRETE All sizes LATALASTIK Not necessary, according to manufacturer
1 bucket of compo-nent A (5 kg)
1 bucket of compo-nent B (2 kg)
R2T 3 m2 1 day 7 days
LITOKOL All sizes LITOELASTIC Not necessary, according to manufacturer 1 bucket (10 kg) R2T 3 m2 12 hours 5 days
PCI - BASF All sizes PCI NANOLIGHTUse of the following
product is compulsory: PCI GISOGRUN 303
1 bag (15 kg) + 9 litres of water C2 TE S1 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBERAll sizes FIX CR Not necessary, according to
manufacturer 1 bucket (10 kg) R2T 3 m2 12 hours 2 daysInstallation with a single-
layer of adhesive(6 mm trowel)
ARDEX All sizes ARDEX X 77 microtec ARDEX P 82 1 bag (25 kg) + 11
litres of waterC2 T(T)E(E) S1 10 m2 8 hours 1 day
For situations in which a
quick setting adhesive is
recommended
MAPEI All sizes KERAQUICK + LATEX PLUS
Not necessary, according to manufacturer
1 bag (25 kg) + 8,5 kg of LATEX
PLUS
C2 FT S2 7 m2 3 hours 1 day
Installation with a double layer of adhesive
KERAKOLL All sizes H40 ECO RAPIDFLEX keragrip eco 1 bag (25 kg) +
6,3 litres of waterC2F TE
S1 6 m2 3 hours 2 days
LATICRETE All sizes LATALASTIK Not necessary, according to manufacturer
1 bucket of component A (5 kg) 1 bucket
of component B (2 kg)
R2T 2 m2 1 day 7 daysInstallation with a single layer of adhesive (6 mm
trowel)
LITOKOL All sizes LITOELASTIC Not necessary, according to manufacturer 1 bucket (10 kg) R2T 3 m2 12 hours 5 days
Installation with a double layer of adhesive
PCI - BASF All sizes PCI NANOLIGHTUse of the following
product is compulsory: PCI GISOGRUN 303
1 bag (15 kg) + 9 litres of water C2 TE S1 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBERAll sizes WEBER.COL
FIX CR Not necessary, according to
manufacturer 1 bucket (10 kg) R2T 3 m2 12 hours 2 daysInstallation with a single-layer of adhesive (6 mm
trowel)ARDEX All sizes ARDEX X 77 S
microtec ARDEX P 82 1 bag (25 kg) + 8,5 litres of water
C2 FT(T)E S1 10 m2 90 min. 6 hours
A.1c - Wall installation in interiors of KERLITE 3mm
(*) Instructions provided directly by manufacturers, who guarantee the information given. For explanations or more details, contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”)”.
(**) Instructions provided directly by manufacturers, who guarantee the information given. If a product is offered in both "white" and a "grey" versions, the mixing ratio may vary. For explanations or more details, contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”)”.
(***) Ratings provided directly by manufacturers, who guarantee the information given, are based on laboratory tests performed at 23° C and with a relative humidity of 50%. In the event of use in different situations or for explanations or more details, contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”)”.
Odpowiedzial-ność instalatora
w sytuacjach kiedy normalne
kleje są polecane
Producent Produkt(*)Rozmiar płyt (cm) Podkład, jeśli konieczny
Niezbędne przy gipsowych, anhydrytowych lub
chłonnych powierzchniach:
Primer G lub ECOPRIM T
Dla gipsowych powierzch-ni: Primer A Eco
Nie konieczne, według zaleceń producenta
Dla gipsowych powierzchni: Primer A Eco
Dla gipsowych powierzchni: PCI GISOGRUND
Użycie następującego produktu jest niezbędne:
PCI GISOGRUN 303
Dla gipsowych powierzchni: WEBER.PRIM PF15
Dla gipsowych powierzchni: ARDEX P 51
Proporcje mieszania (**)
Klasa (*)
nominalne pokrycie
(*)
możliwość obróbki
(***)
gotowe do użycia (***)
montaż (*)
Instrukcje podane bezpośrednio przez producentów, którzy gwarantują poprawność informacji. Po więcej szczegółów, skontaktuj się ze wsparciem technicznym odpowiednich producentów (zobacz “9 - Przydatne kontakty”) “.
Instrukcje podane bezpośrednio przez producentów, którzy gwarantują poprawność informacji. Jeśli produkt jest oferowany zarówno w wersjach “biały” i “szary” , proporcje mieszania mogą się różnić. Po więcej szczegółów, skontaktuj się ze wsparciem technicznym odpowiednich producentów (zobacz “9 - Przydatne kontakty”) “.
Instrukcje podane bezpośrednio przez producentów, którzy gwarantują poprawność informacji. Na podstawie badań laboratoryjnych przeprowadzonych w temperaturze 23 ° C i przy wilgotności względnej 50%. W przypadku zastosowania w innych sytuacjach lub w celu uzyskania więcej szczegółów, skontaktuj się ze wsparciem technicznym odpowiednich producentów (zobacz “9 - Przydatne kontakty”) “.
a.1c- KERLITE 3mm - montaż na ścianie we wnętrzach
materiał podłoża: płyta wiórowa, metal
Niezbędne przy gipsowych, anhydrytowych lub
chłonnych powierzchniach:
Primer G lub ECOPRIM T
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
1 paczka (25 kg) + 8,5 litra wody
1 paczka (25 kg) + 6,3 litra wody
1 paczka (25 kg) + 8,5 kg LATEX PLUS
1 wiadro (10 kg)
1 wiadro (10 kg)
1 paczka (15 kg) + 9 litrów wody
1 paczka (25 kg) + 7 litrów wody
1 paczka (25 kg) + 9 litrów wody
1 paczka (25 kg) + 6 litrów wody
1 biała paczka (25 kg) 7,2 - 9,5 litra
wody
1 szara paczka (25 kg) 7,1 - 8,8 litra
wody
1 paczka (15 kg) + 5,9/6,2 litra wody
1 paczka (15 kg) + 8,4/8,7 litra wody
1 paczka (25 kg) + 7,2/7,7 litra wody
8 godzin
8 godzin
20 godzin
1 dzień
1 dzień
1 dzień
1 dzień
1 dzień
1 dzień
2 dni
2 dni
3 godziny
3 godziny
4 godziny
6 godzin
3 dni
Montaż z podwójną warstwą kleju
Montaż z podwójną warstwą kleju
Montaż z podwójną warstwą kleju
Montaż z pojedyńczą warstwą kleju (kielnia
6 mm)
Montaż z pojedyńczą warstwą kleju (kielnia
6 mm)
Montaż z pojedyńczą warstwą kleju (kielnia
6 mm)
14 dni
14 dni
14 dni
14 dni8 godzin
8 godzin
8 godzin
8 godzin
1 paczka (25 kg) + 8,5 kg ISOLASTIC
1 wiadro kompo-nentu A (5 kg)
1 wiadro kompo-nentu B (2 kg)
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
w sytuacjach kiedy szybkow-iążące kleje są
polecane
40 4140 41
KERLITE Cotto d’Este > KERLITE Technical Manual
Supporting material: two-coat plaster, gypsum plaster, plasterboard, fibre cement panels
A.2a - Wall installation in interiors of KERLITE 3plus and KERLITE 5plus
At the discretion
of I.S.
Manufac-turer
Size of slabs(cm)
Product(*)
Primer, if necessary(*) Mixing ratio (**) Class
(*)
Nominal cover-age (*)
Workability (***)
Ready for use(***)
Installation(*)
For situations in which a
normal setting adhesives is
recommended
MAPEI
50x50; 100x40; 100x50
KERAFLEX MAXI S1 COMPULSORY for gypsum-based, anhydride
or absorbent surfaces:
Primer G or ECOPRIM T
1 bag (25 kg) + 7,2/7,7 litres of water C2 TE S1
7 m2
8 hours 14 days
Installation with a double layer of adhesive
ULTRALITE S1 1 bag (15 kg) + 8,4/8,7 litres of water C2 TE S1
100x100; 300x100ULTRALITE S2 1 bag (15 kg) +
5,9/6,2 litres of water C2 E S2 6,3 m2
KERABOND + ISOLASTIC
1 bag (25 kg) + 8,5 kg of ISOLASTIC C2 E S2 6,5 m2
KERAKOLL All sizes H40 NO LIMITS For gypsum-based surfaces: Primer A Eco
Grey 1 bag (25 kg) from 7,1 to
8,8 litres of waterC2 TE S1 6 m2 20 hours 3 days
White 1 bag (25 kg) from 7,2 to
9,5 litres of water
LATICRETE All sizes LATICRETE 254 Platinum
Not necessary, according to manufacturer
1 bag (25 kg) + 6 litres of water C2 TE S1 5 m2 1 day 7 days
LITOKOL
50x50;100x40; 100x50 SUPERFLEX K77
For gypsum-based surfaces: Primer C
1 bag (25 kg) + 8,5 litres of water C2 TE S1 6 m2
8 hours 7 days100x100; 300x100
CEMENTKOL K21 + LATEXKOL
1 bag (25 kg) + 7,5 kg of LATEXKOL C2 S2 5 m2
PCI - BASF All sizes PCI NANOLIGHT + PCI LASTOFLEX
For gypsum-based surfaces: PCI GISOGRUND
1 bag (15 kg) + 1 can of PCI LASTOFLEX (4 kg) + 5 litres of water
C2 TE S2 5,5 m2 8 hours 1 day
SAINT-GOBAIN / WEBER All sizes
WEBER.COL PRO HP For gypsum-based surfaces:
WEBER.PRIM PF15
1 bag (25 kg) + 7 litres of water C2 TE S1
5 m2
8 hours14 days
WEBER.COL PRO HF LIGHT
1 bag (15 kg) + 8 litres of water C2 TE S2 1 day
ARDEX All sizesARDEX X 77
microtec + ARDEX E 90
For gypsum-based surfaces: ARDEX P 51
1 bag (25 kg) + 1 can of ARDEX E 90 (4,5
kg) + 9 litres of water
C2 T(T)E(E) S2 10 m2 8 hours 1 day Installation with a single layer
of adhesive (6 mm trowel)
For situations in which a
quick setting adhesive is
recommended
MAPEI
50x50; 100x40; 100x50
GRANIRAPID
COMPULSORY for gypsum-based, anhydride or absorbent
surfaces:Primer G or ECOPRIM T
Component A: 1 bag (25 kg) Component
B: tub (5,5 kg)C2 F S1
6 m2
3 hours 1 day
Installation with a double layer of adhesive
ULTRALITE S1 QUICK 1 bag (15 kg) +
5,1/5,7 litres of water
C2 FTE S1
100x100; 300x100
ULTRALITE S2 QUICK C2 FE S2 7 m2
ELASTORAPIDComponent A: 1 bag (25 kg) Component
B: tub (6,5 kg)C2 FTE S2 6 m2
KERAKOLL All sizes H40 ECO RAPIDFLEX
For gypsum-based surfaces: Primer A Eco
1 bag (25 kg) + 6,3 litres of water
C2F TE S1 6 m2 3 hours 2 days
LATICRETE All sizes
LATICRETE 335 Rapid Super Flex + LATICRETE 282
Latex Additive
Not necessary, according to manufacturer
1 bag (25 kg) + 6/7 litres of latex C2 TE F 5 m2 6 hours 2 days
LITOKOL
50x50;100x40; 100x50
LITOSTONE K99 + LATEXKOL + water For gypsum-based surfaces:
Primer C
1 bag (25 kg) + 3,5 litres of LATEXKOL +
3,5 litres of waterC2 FE S1
5 m2 4 hours 1 day
100x100; 300x100
LITOSTONE K99 + LATEXKOL
1 bag (25 kg) + 7,5 kg of LATEXKOL C2 FE S2
PCI - BASF All sizes PCI NANOLIGHT + PCI LASTOFLEX
For gypsum-based surfaces: PCI GISOGRUND
1 bag (15 kg) + 1 can of PCI LASTOFLEX (4 kg) + 5 litres of water
C2 TE S2 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBERAll sizes
WEBER.COL PRO MARMO + WEBER
L50 For old ceramic tile, marble slabs and stone:
WEBER. FLOOR 4716 Prime
1 bag (25 kg)+ 7 litres of WEBER L50
C2 FT S1 5 m2 4 hours 3 days
WEBER.COL PRO RAPID + WEBER
L50
1 bag (25 kg)+ 6-6,5 litres of
WEBER L50
ARDEX All sizesARDEX X 77 S
microtec + ARDEX E 90
For gypsum-based surfaces: ARDEX P 51
1 bag (25 kg) + 3 kg of ARDEX E 90 + 7,5
litres of water
C2 FT(T)E S2 10 m2 90 min. 6 hours Installation with a single layer
of adhesive (6 mm trowel)
(*) Instructions provided directly by manufacturers, who guarantee the information given. For explanations or more details, contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”)”.
(**) Instructions provided directly by manufacturers, who guarantee the information given. If a product is offered in both "white" and a "grey" versions, the mixing ratio may vary. For explanations or more details, contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”)”.
(***) Ratings provided directly by manufacturers, who guarantee the information given, are based on laboratory tests performed at 23° C and with a relative humidity of 50%. In the event of use in different situations or for explanations or more details, contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”)”.
Supporting material: particle board, metal
At the discretion
of I.S.
Manufac-turer
Size of slabs(cm)
Product(*)
Primer, if necessary(*) Mixing ratio (**) Class
(*)
Nominal cover-age (*)
Workability (***)
Ready for use(***)
Installation(*)
For situations in which a
normal setting adhesives is
recommended
MAPEI All sizes
KERALASTIC
Not necessary, according to manufacturer
1 can (10 kg) R2
3 m2 12 hours 7 days
Installation with a double layer of adhesive
KERALASTIC T 1 can (10 kg) R2T
KERAKOLL All sizes H40 NO LIMITS KERAGRIP ECO
Grey 1 bag (25 kg)from 7,1 to 8,8 litres of water
C2 TE S1 6 m2 20 hours 3 daysWhite 1 bag (25 kg) from 7,2 to
9,5 litres of water
LATICRETE All sizes LATALASTIK Not necessary, according to manufacturer
1 bucket of compo-nent A (5 kg)
1 bucket of compo-nent B (2 kg)
R2T 3 m2 1 day 7 days
LITOKOL All sizes LITOELASTIC Not necessary, according to manufacturer 1 bucket (10 kg) R2T 3 m2 12 hours 5 days
PCI - BASF All sizes PCI NANOLIGHTUse of the following
product is compulsory: PCI GISOGRUN 303
1 bag (15 kg) + 9 litres of water C2 TE S1 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBERAll sizes FIX CR Not necessary, according to
manufacturer 1 bucket (10 kg) R2T 3 m2 12 hours 2 daysInstallation with a single-
layer of adhesive(6 mm trowel)
ARDEX All sizes ARDEX X 77 microtec ARDEX P 82 1 bag (25 kg) + 11
litres of waterC2 T(T)E(E) S1 10 m2 8 hours 1 day
For situations in which a
quick setting adhesive is
recommended
MAPEI All sizes KERAQUICK + LATEX PLUS
Not necessary, according to manufacturer
1 bag (25 kg) + 8,5 kg of LATEX
PLUS
C2 FT S2 7 m2 3 hours 1 day
Installation with a double layer of adhesive
KERAKOLL All sizes H40 ECO RAPIDFLEX keragrip eco 1 bag (25 kg) +
6,3 litres of waterC2F TE
S1 6 m2 3 hours 2 days
LATICRETE All sizes LATALASTIK Not necessary, according to manufacturer
1 bucket of component A (5 kg) 1 bucket
of component B (2 kg)
R2T 2 m2 1 day 7 daysInstallation with a single layer of adhesive (6 mm
trowel)
LITOKOL All sizes LITOELASTIC Not necessary, according to manufacturer 1 bucket (10 kg) R2T 3 m2 12 hours 5 days
Installation with a double layer of adhesive
PCI - BASF All sizes PCI NANOLIGHTUse of the following
product is compulsory: PCI GISOGRUN 303
1 bag (15 kg) + 9 litres of water C2 TE S1 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBERAll sizes WEBER.COL
FIX CR Not necessary, according to
manufacturer 1 bucket (10 kg) R2T 3 m2 12 hours 2 daysInstallation with a single-layer of adhesive (6 mm
trowel)ARDEX All sizes ARDEX X 77 S
microtec ARDEX P 82 1 bag (25 kg) + 8,5 litres of water
C2 FT(T)E S1 10 m2 90 min. 6 hours
A.1c - Wall installation in interiors of KERLITE 3mm
(*) Instructions provided directly by manufacturers, who guarantee the information given. For explanations or more details, contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”)”.
(**) Instructions provided directly by manufacturers, who guarantee the information given. If a product is offered in both "white" and a "grey" versions, the mixing ratio may vary. For explanations or more details, contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”)”.
(***) Ratings provided directly by manufacturers, who guarantee the information given, are based on laboratory tests performed at 23° C and with a relative humidity of 50%. In the event of use in different situations or for explanations or more details, contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”)”.
Odpowiedzial-ność instalatora
w sytuacjach kiedy normalne
kleje są polecane
Producent Produkt(*)Rozmiar płyt (cm) Podkład, jeśli konieczny
Nie konieczne, według zaleceń producenta
Dla starych płytek ceramic-znych, marmurów i kamieni
naturalnych: WEBER. FLOOR 4716 Prime
Dla gipsowych powierzchni: Primer C
Dla gipsowych powierzchni: Primer C
Dla gipsowych powierzchni: Primer A Eco
Dla gipsowych powierzchni: Primer A Eco
Dla gipsowych powierzchni: PCI GISOGRUND
Dla gipsowych powierzchni: ARDEX P51
Dla gipsowych powierzchni: ARDEX P51
Dla gipsowych powierzchni: WEBER.PRIM PF15
Proporcje mieszania (**)
Klasa (*)
nominalne pokrycie
(*)
możliwość obróbki
(***)
gotowe do użycia (***)
montaż (*)
Instrukcje podane bezpośrednio przez producentów, którzy gwarantują poprawność informacji. Po więcej szczegółów, skontaktuj się ze wsparciem technicznym odpowiednich producentów (zobacz “9 - Przydatne kontakty”) “.
Instrukcje podane bezpośrednio przez producentów, którzy gwarantują poprawność informacji. Jeśli produkt jest oferowany zarówno w wersjach “biały” i “szary” , proporcje mieszania mogą się różnić. Po więcej szczegółów, skontaktuj się ze wsparciem technicznym odpowiednich producentów (zobacz “9 - Przydatne kontakty”) “.
Instrukcje podane bezpośrednio przez producentów, którzy gwarantują poprawność informacji. Na podstawie badań laboratoryjnych przeprowadzonych w temperaturze 23 ° C i przy wilgotności względnej 50%. W przypadku zastosowania w innych sytuacjach lub w celu uzyskania więcej szczegółów, skontaktuj się ze wsparciem technicznym odpowiednich producentów (zobacz “9 - Przydatne kontakty”) “.
materiał podłoża: podwójna warstwa tynku, tynk gipsowy, płyta gipsowa, panele włokienno-cementowe
a.2a- KERLITE 3plus i KERLITE 5plus- montaż na ścianie we wnętrzach
Niezbędne przy gipsowych, anhydrytowych lub
chłonnych powierzchniach:
Primer G lub ECOPRIM T
Niezbędne przy gipsowych, anhydrytowych lub
chłonnych powierzchniach:
Primer G lub ECOPRIM T
Nie konieczne, według zaleceń producenta
1 paczka (25 kg) + 7 litrów
WEBER L50
1 paczka (25 kg) + 6-6,5 litrówWEBER L50
1 paczka (25 kg) + 3,5 litra LATEXKOL
+ 3,5 litra wody
1 paczka (25 kg) + 6/7 litrów latexu
1 paczka (25 kg) + 6,3 litra wody
1 paczka (15 kg) + 5,1/5,7 litra wody
1 paczka (25 kg) + 7 litrów wody
1 paczka (25 kg) + 1 puszka ARDEX E90
(4,5kg)+ 9 litrów wody
1 paczka (15 kg) + 1 puszka PCI LASTOFLEX
(4kg)+ 5 litrów wody
1 paczka (15 kg) + 1 puszka PCI LASTOFLEX
(4kg)+ 5 litrów wody
1 paczka (25 kg) + 6 litrów wody
1 paczka (25 kg) + 8,5 litrów wody
1 paczka (15 kg) + 8 litrów wody
1 paczka (25 kg) + 7,5 kg LATEXKOL
1 paczka (25 kg) + 7,5 kg LATEXKOL
1 biała paczka (25 kg) 7,2 - 9,5 litra
wody
1 szara paczka (25 kg) 7,1 - 8,8 litra
wody
1 paczka (15 kg) + 5,9/6,2 litra wody
1 paczka (15 kg) + 8,4/8,7 litra wody
1 paczka (25 kg) + 7,2/7,7 litra wody
8 godzin
20 godzin
1 dzień
1 dzień
1 dzień
1 dzień
1 dzień
1 dzień
1 dzień
2 dni
2 dni
3 dni
6 godzin
4 godziny
4 godziny
3 godziny
3 godziny
90 min
6 godzin
8 godzin
3 dni
Montaż z podwójną warstwą kleju
Montaż z podwójną warstwą kleju
Montaż z pojedyńczą warstwą kleju (kielnia 6 mm)
Montaż z pojedyńczą warstwą kleju (kielnia 6 mm)
14 dni
7 dni7 dni
7 dni
14 dni
8 godzin
8 godzin
8 godzin
8 godzin
1 paczka (25 kg) + 8,5 kg ISOLASTIC
Komponent A: 1 paczka (25 kg)
Komponent B: opa-kowanie (6,5 kg)
Komponent A: 1 paczka (25 kg)
Komponent B: opa-kowanie (5,5 kg)
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
w sytuacjach kiedy szybkow-iążące kleje są
polecane
1 paczka (25 kg) + 1 puszka ARDEX E90
(4,5kg)+ 9 litrów wody
Dla gipsowych powierzchni: PCI GISOGRUND
42 4342 43
KERLITE Cotto d’Este > KERLITE Technical Manual
Supporting material: particle board, metal
A.2c - Wall installation in interiors of KERLITE 3plus and KERLITE 5plus
At the discretion
of I.S.
Manufac-turer
Size of slabs(cm)
Product(*)
Primer, if necessary(*) Mixing ratio (**) Class
(*)
Nominal cover-age (*)
Workability (***)
Ready for use(***)
Installation(*)
For situations in which a
normal setting adhesives is
recommended
MAPEI All sizes
KERALASTIC Not necessary, according to
manufacturer 1 can (10 kg)
R2
3 m2 12 hours 7 daysInstallation with a single-layer of adhesive (6 mm
trowel)KERALASTIC T R2T
KERAKOLL All sizes SUPERFLEX ECO Not necessary, according to manufacturer 1 bucket (8 kg) R2T 3 m2 12 hours 3 days
Installation with a double layer of adhesive
KERAKOLL All sizes H40 NO LIMITS KERAGRIP ECO
Grey 1 bag (25 kg) from 7,1 to
8,8 litres of waterC2 TE S1 6 m2 20 hours 3 days
White 1 bag (25 kg) from 7,2 to
9,5 litres of water
LATICRETE All sizes LATALASTIK Not necessary, according to manufacturer
1 bucket of component A (5 kg) 1 bucket
of component B (2 kg)
R2T 3 m2 1 day 7 days
LITOKOL All sizes LITOELASTIC Not necessary, according to manufacturer 1 bucket (10 kg) R2T 3 m2 12 hours 5 days
PCI - BASF All sizes PCI NANOLIGHT + PCI LASTOFLEX
Use of the following product is COMPULSORY: PCI
GISOGRUN 303
1 bag (15 kg) + 1 can of PCI
LASTOFLEX (4 kg) + 5 litres of water
C2 TE S2 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBERAll sizes WEBER.COL.FIX CR Not necessary, according to
manufacturer 1 bucket (10 kg) R2 T 3 m2 12 hours 2 days
Installation with a single-layer of adhesive (6 mm
trowel)ARDEX All sizes
ARDEX X 77 microtec + ARDEX
E 90ARDEX P 82
1 bag (25 kg) + 1 can of ARDEX E 90 (4,5 kg) + 9 litres of
water
C2 T(T)E(E) S2 10 m2 8 hours 1 day
For situations in which a
quick setting adhesive is
recommended
MAPEI All sizes KERAQUICK + LATEX PLUS
Not necessary, according to manufacturer
1 bag (25 kg) + 8,5 kg of LATEX PLUS C2 FT S2 7 m2 3 hours 1 day
Installation with a single-layer of adhesive (6 mm
trowel)
KERAKOLL All sizes H40 ECO RAPIDFLEX KERAGRIP ECO 1 bag (25 kg) +
6,3 litres of waterC2F TE
S1 6 m2 3 hours 2 days
Installation with a double layer of adhesive
LATICRETE All sizes LATALASTIK Not necessary, according to manufacturer
1 bucket of component A (5 kg) 1 bucket
of component B (2 kg)
R2T 3 m2 1 day 7 days
LITOKOL All sizes LITOELASTIC Not necessary, according to manufacturer 1 bucket (10 kg) R2T 3 m2 12 hours 5 days
PCI - BASF All sizes PCI NANOLIGHT + PCI LASTOFLEX
Use of the following product is COMPULSORY: PCI
GISOGRUN 303
1 bag (15 kg) + 1 can of PCI
LASTOFLEX (4 kg) + 5 litres of water
C2 TE S2 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBERAll sizes WEBER.COL.FIX CR Not necessary, according to
manufacturer 1 bucket (10 kg) R2 T 3 m2 12 hours 2 days
Installation with a single-layer of adhesive (6 mm
trowel)
ARDEX All sizesARDEX X 77 S
microtec + ARDEX E 90
ARDEX P 821 bag (25 kg) + 3
kg of ARDEX E 90 + 7,5 litres of water"
C2 F(F)T E S2 10 m2 90 min. 6 hours
(*) Instructions provided directly by manufacturers, who guarantee the information given. For explanations or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
(**) Instructions provided directly by manufacturers, who guarantee the information given. If a product is offered in both "white" and a "grey" versions, the mixing ratio may vary. For explana-tions or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
(***) Ratings provided directly by manufacturers, that guarantee the information given, based on laboratory tests performed at 23° C and with a relative humidity of 50%. For use in different situations, contact the technical support office of the respective manufacturers. For explanations or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
Supporting material: concrete, old ceramic tile, marble, stone
A.2b - Wall installation in interiors of KERLITE 3plus and KERLITE 5plus
(*) Instructions provided directly by manufacturers, who guarantee the information given. For explanations or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
(**) Instructions provided directly by manufacturers, who guarantee the information given. If a product is offered in both "white" and a "grey" versions, the mixing ratio may vary. For explana-tions or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
(***) Ratings provided directly by manufacturers, that guarantee the information given, based on laboratory tests performed at 23° C and with a relative humidity of 50%. For use in different situations, contact the technical support office of the respective manufacturers. For explanations or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
At the discretion
of I.S.
Manufac-turer
Size of slabs(cm)
Product(*)
Primer, if necessary(*) Mixing ratio (**) Class
(*)
Nominal cover-age (*)
Workability (***)
Ready for use(***)
Installation(*)
For situations in which a
normal setting adhesives is
recommended
MAPEI
50x50; 100x40; 100x50
KERAFLEX MAXI S1
If levelling is necessary, on the above mentioned
supports, apply the following product beforehand
ECOPRIM GRIP
1 bag (25 kg) + 7,2/7,7 litres of
waterC2 TE S1
7 m2
8 hours 14 days
Installation with a double layer of adhesive
ULTRALITE S11 bag (15 kg) + 8,4/8,7 litres of
waterC2 TE S1
100x100; 300x100
ULTRALITE S21 bag (15 kg) + 5,9/6,2 litres of
waterC2 E S2 6,3 m2
KERABOND + ISOLASTIC
1 bag (25 kg) + 8,5 kg of ISOLA-
STICC2 E S2 6,5 m2
KERAKOLL All sizes H40 NO LIMITS Not necessary, according to manufacturer
Grey 1 bag (25 kg) from 7,1 to
8,8 litres of waterC2 TE S1 6 m2 20 hours 3 days
White 1 bag (25 kg) from 7,2 to
9,5 litres of water
LATICRETE All sizes LATICRETE 254 Platinum
Not necessary, according to manufacturer
1 bag (25 kg) + 6 litres of water C2 TE S1 5 m2 1 day 7 days
LITOKOL
50x50;100x40; 100x50 SUPERFLEX K77
Not necessary, according to manufacturer
1 bag (25 kg) + 8,5 litres of water C2 TE S1 6 m2
8 hours 7 days100x100; 300x100
CEMENTKOL K21 + LATEXKOL
1 bag (25 kg) + 7,5 kg of LATEXKOL C2 S2 5 m2
PCI - BASF All sizes PCI NANOLIGHT + PCI LASTOFLEX
On non-absorbent supportsPCI GISOGRUN 303
1 bag (15 kg) + 1 can of PCI
LASTOFLEX (4 kg) + 5 litres of water
C2 TE S2 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBERAll sizes WEBER.COL PRO
HP + WEBER L50
For old ceramic tile, marble slabs and stone:
WEBER. FLOOR 4716 Prime
1 bag (15 kg) + 7 litres of WEBER
L50C2 TE S2 5 m2 8 hours 14 days
ARDEX All sizesARDEX X 77
microtec + ARDEX E 90
As an alternative for old ceramic tile, marble slabs and stone:- ARDEX P 4 -
ARDEX X 77 (rough levelled)
1 bag (25 kg) + 1 can of ARDEX E 90 (4,5 kg) + 9 litres
of water
C2 T(T)E(E) S2 10 m2 8 hours 1 day
Installation with a single layer of adhesive (6 mm
trowel)
For situations in which a
quick setting adhesive is
recommended
MAPEI
50x50; 100x40; 100x50
GRANIRAPID
If levelling is necessary, on the above mentioned supports, apply ECOPRIM
GRIP beforehand
Component A: 1 bag (25 kg)
Component B: tub (5,5 kg)
C2 F S1
6 m2
3 hours 1 day
Installation with a double layer of adhesive
ULTRALITE S1 QUICK 1 bag (15 kg) +
5,1/5,7 litres of water
C2 FTE S1
100x100; 300x100
ULTRALITE S2 QUICK C2 FE S2 7 m2
ELASTORAPID
Component A: 1 bag (25 kg)
Component B: tub (6,5 kg)
C2 FTE S2 6 m2
KERAKOLL All sizes H40 ECO RAPIDFLEX
Not necessary, according to manufacturer
1 bag (25 kg) + 6,3 litres of water
C2F TE S1 6 m2 3 hours 2 days
LATICRETE All sizes
LATICRETE 335 Rapid Super Flex + LATICRETE 282
Latex Additive
Not necessary, according to manufacturer
1 bag (25 kg) + 6/7 litres of latex C2 TE F 5 m2 6 hours 2 days
LITOKOL
50x50;100x40; 100x50
LITOSTONE K99 + LATEXKOL + water For gypsum-based surfaces:
Primer C
1 bag (25 kg) + 3,5 litres of LATEXKOL
+ 3,5 litres of water
C2 FE S15 m2 4 hours 1 day
100x100; 300x100
LITOSTONE K99 + LATEXKOL
1 bag (25 kg) + 7,5 kg of LATEXKOL C2 FE S2
PCI - BASF All sizes PCI NANOLIGHT + PCI LASTOFLEX
On non-absorbent supportsPCI GISOGRUN 303
1 bag (15 kg) + 1 can of PCI
LASTOFLEX (4 kg) + 5 litres of water
C2 TE S2 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBER
50x50; 100x40; 100x50; 100x100
WEBER.COL PRO MARMO + WEBER
L50 For old ceramic tile, marble slabs and stone:
WEBER. FLOOR 4716 Prime
1 bag (25 kg)+ 7 litres of WEBER L50
C2 FT S1 5 m2 4 hours 3 days
WEBER.COL PRO RAPID + WEBER
L50
1 bag (25 kg)+ 6-6,5 litres of
WEBER L50
ARDEX All sizesARDEX X 77 S
microtec + ARDEX E 90
As an alternative for old ceramic tile, marble slabs and stone:- ARDEX P 4 -
ARDEX X 77 (rough levelled)
1 bag (25 kg) + 3 kg of ARDEX E 90 + 7,5 litres of
water
C2 FT(T)E S2 10 m2 90 min. 6 hours
Installation with a single layer of adhesive (6 mm
trowel)
Odpowiedzial-ność instalatora
w sytuacjach kiedy normalne
kleje są polecane
Producent Produkt(*)Rozmiar płyt (cm) Podkład, jeśli konieczny
Niezbędne przy gipsowych, anhydrytowych lub
chłonnych powierzchniach:
Primer G lub ECOPRIM T
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Dla gipsowych powierzchni: Primer C
Dla gipsowych powierzchni: PCI GISOGRUN 303
Proporcje mieszania (**)
Klasa (*)
nominalne pokrycie
(*)
możliwość obróbki
(***)
gotowe do użycia (***)
montaż (*)
Instrukcje podane bezpośrednio przez producentów, którzy gwarantują poprawność informacji. Po więcej szczegółów, skontaktuj się ze wsparciem technicznym odpowiednich producentów (zobacz “9 - Przydatne kontakty”) “.
Instrukcje podane bezpośrednio przez producentów, którzy gwarantują poprawność informacji. Jeśli produkt jest oferowany zarówno w wersjach “biały” i “szary” , proporcje mieszania mogą się różnić. Po więcej szczegółów, skontaktuj się ze wsparciem technicznym odpowiednich producentów (zobacz “9 - Przydatne kontakty”) “.
Instrukcje podane bezpośrednio przez producentów, którzy gwarantują poprawność informacji. Na podstawie badań laboratoryjnych przeprowadzonych w temperaturze 23 ° C i przy wilgotności względnej 50%. W przypadku zastosowania w innych sytuacjach lub w celu uzyskania więcej szczegółów, skontaktuj się ze wsparciem technicznym odpowiednich producentów (zobacz “9 - Przydatne kontakty”) “.
a.2b- KERLITE 3plus i KERLITE 5plus- montaż na ścianie we wnętrzach
materiał podłoża: beton, stare płytki ceramiczne, marmur, kamień naturalny
Niezbędne przy gipsowych, anhydrytowych lub
chłonnych powierzchniach:
Primer G lub ECOPRIM T
Dla niechłonnych powier-zchni: PCI GISOGRUN 303
Dla starych płytek ceramic-znych, marmuru i kamienia naturalnego: WEBER.FLOOR
4716 Prime
Dla starych płytek ceramicznych, marmuru i kamienia naturalne-go: WEBER.FLOOR 4716 Prime
Jako alternatywa dla starych płytek ceramicznych, marmuru i kamienia naturalnego: -ARDEX
P 4 - ARDEX X 77 (wstępnie wypoziomowane)
Jako alternatywa dla starych płytek ceramicznych, marmuru i kamienia naturalnego: -ARDEX
P 4 - ARDEX X 77 (wstępnie wypoziomowane)
1 paczka (25 kg) + 6-6,5 litra
WEBER L50
1 paczka (25 kg) + 3 kg ARDEX E90 + 7,5
litra wody
1 paczka (15 kg) + 1 puszka PCI
LASTOFLEX (4kg) + 5 litrów wody
1 paczka (25 kg) + 7 litrów
WEBER L50
1 paczka (25 kg) + 3,5 litra LATEXKOL
+ 3,5 litra wody
1 paczka (25 kg) + 7,5 kg LATEXKOL
1 paczka (25 kg) + 6/7 litrów latexu
1 paczka (25 kg) + 6,3 litra wody
1 paczka (15 kg) + 5,1/5,7 litra wody
1 paczka (25 kg) + 7,5 kg LATEXKOL1 paczka (15 kg) + 1 puszka PCI
LASTOFLEX (4 kg) + 5 litrów wody
1 paczka (15 kg) + 1 puszka ARDEX E 90(4,5 kg) + 9
litrów wody
1 paczka (25 kg) + 8,5 litra wody
1 paczka (25 kg) + 6 litrów wody
1 biała paczka (25 kg) 7,2 - 9,5 litra
wody
1 szara paczka (25 kg) 7,1 - 8,8 litra
wody
1 paczka (15 kg) + 5,9/6,2 litra wody
1 paczka (15 kg) + 8,4/8,7 litra wody
1 paczka (25 kg) + 7,2/7,7 litra wody
8 godzin
20 godzin
1 dzień
1 dzień
1 dzień
1 dzień
1 dzień
1 dzień
2 dni
2 dni
3 dni
6 godzin
4 godziny
3 godziny
3 godziny
90 min
4 godziny
6 godzin
8 godzin
3 dniMontaż z podwójną
warstwą kleju
Montaż z podwójną warstwą kleju
Montaż z pojedyńczą warstwą kleju (kielnia 6 mm)
Montaż z pojedyńczą warstwą kleju (kielnia 6 mm)
14 dni
7 dni
7 dni
14 dni
8 godzin
8 godzin
8 godzin
8 godzin
1 paczka (25 kg) + 8,5 kg ISOLASTIC
Komponent A: 1 paczka (25 kg)
Komponent B: opa-kowanie (6,5 kg)
Komponent A: 1 paczka (25 kg)
Komponent B: opa-kowanie (5,5 kg)
Wszystkie rozmiary
Wszystkie rozmiary
100 x 100300 x 100
100 x 100300 x 100
100 x 100300 x 100
100 x 100300 x 100
50x50; 100x40; 100x50
50x50; 100x40; 100x50
50x50; 100x40; 100x50
50x50; 100x40; 100x50
50x50; 100x40; 100x50; 100x100
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
w sytuacjach kiedy szybkow-iążące kleje są
polecane
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
42 4342 43
KERLITE Cotto d’Este > KERLITE Technical Manual
Supporting material: particle board, metal
A.2c - Wall installation in interiors of KERLITE 3plus and KERLITE 5plus
At the discretion
of I.S.
Manufac-turer
Size of slabs(cm)
Product(*)
Primer, if necessary(*) Mixing ratio (**) Class
(*)
Nominal cover-age (*)
Workability (***)
Ready for use(***)
Installation(*)
For situations in which a
normal setting adhesives is
recommended
MAPEI All sizes
KERALASTIC Not necessary, according to
manufacturer 1 can (10 kg)
R2
3 m2 12 hours 7 daysInstallation with a single-layer of adhesive (6 mm
trowel)KERALASTIC T R2T
KERAKOLL All sizes SUPERFLEX ECO Not necessary, according to manufacturer 1 bucket (8 kg) R2T 3 m2 12 hours 3 days
Installation with a double layer of adhesive
KERAKOLL All sizes H40 NO LIMITS KERAGRIP ECO
Grey 1 bag (25 kg) from 7,1 to
8,8 litres of waterC2 TE S1 6 m2 20 hours 3 days
White 1 bag (25 kg) from 7,2 to
9,5 litres of water
LATICRETE All sizes LATALASTIK Not necessary, according to manufacturer
1 bucket of component A (5 kg) 1 bucket
of component B (2 kg)
R2T 3 m2 1 day 7 days
LITOKOL All sizes LITOELASTIC Not necessary, according to manufacturer 1 bucket (10 kg) R2T 3 m2 12 hours 5 days
PCI - BASF All sizes PCI NANOLIGHT + PCI LASTOFLEX
Use of the following product is COMPULSORY: PCI
GISOGRUN 303
1 bag (15 kg) + 1 can of PCI
LASTOFLEX (4 kg) + 5 litres of water
C2 TE S2 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBERAll sizes WEBER.COL.FIX CR Not necessary, according to
manufacturer 1 bucket (10 kg) R2 T 3 m2 12 hours 2 days
Installation with a single-layer of adhesive (6 mm
trowel)ARDEX All sizes
ARDEX X 77 microtec + ARDEX
E 90ARDEX P 82
1 bag (25 kg) + 1 can of ARDEX E 90 (4,5 kg) + 9 litres of
water
C2 T(T)E(E) S2 10 m2 8 hours 1 day
For situations in which a
quick setting adhesive is
recommended
MAPEI All sizes KERAQUICK + LATEX PLUS
Not necessary, according to manufacturer
1 bag (25 kg) + 8,5 kg of LATEX PLUS C2 FT S2 7 m2 3 hours 1 day
Installation with a single-layer of adhesive (6 mm
trowel)
KERAKOLL All sizes H40 ECO RAPIDFLEX KERAGRIP ECO 1 bag (25 kg) +
6,3 litres of waterC2F TE
S1 6 m2 3 hours 2 days
Installation with a double layer of adhesive
LATICRETE All sizes LATALASTIK Not necessary, according to manufacturer
1 bucket of component A (5 kg) 1 bucket
of component B (2 kg)
R2T 3 m2 1 day 7 days
LITOKOL All sizes LITOELASTIC Not necessary, according to manufacturer 1 bucket (10 kg) R2T 3 m2 12 hours 5 days
PCI - BASF All sizes PCI NANOLIGHT + PCI LASTOFLEX
Use of the following product is COMPULSORY: PCI
GISOGRUN 303
1 bag (15 kg) + 1 can of PCI
LASTOFLEX (4 kg) + 5 litres of water
C2 TE S2 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBERAll sizes WEBER.COL.FIX CR Not necessary, according to
manufacturer 1 bucket (10 kg) R2 T 3 m2 12 hours 2 days
Installation with a single-layer of adhesive (6 mm
trowel)
ARDEX All sizesARDEX X 77 S
microtec + ARDEX E 90
ARDEX P 821 bag (25 kg) + 3
kg of ARDEX E 90 + 7,5 litres of water"
C2 F(F)T E S2 10 m2 90 min. 6 hours
(*) Instructions provided directly by manufacturers, who guarantee the information given. For explanations or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
(**) Instructions provided directly by manufacturers, who guarantee the information given. If a product is offered in both "white" and a "grey" versions, the mixing ratio may vary. For explana-tions or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
(***) Ratings provided directly by manufacturers, that guarantee the information given, based on laboratory tests performed at 23° C and with a relative humidity of 50%. For use in different situations, contact the technical support office of the respective manufacturers. For explanations or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
Supporting material: concrete, old ceramic tile, marble, stone
A.2b - Wall installation in interiors of KERLITE 3plus and KERLITE 5plus
(*) Instructions provided directly by manufacturers, who guarantee the information given. For explanations or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
(**) Instructions provided directly by manufacturers, who guarantee the information given. If a product is offered in both "white" and a "grey" versions, the mixing ratio may vary. For explana-tions or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
(***) Ratings provided directly by manufacturers, that guarantee the information given, based on laboratory tests performed at 23° C and with a relative humidity of 50%. For use in different situations, contact the technical support office of the respective manufacturers. For explanations or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
At the discretion
of I.S.
Manufac-turer
Size of slabs(cm)
Product(*)
Primer, if necessary(*) Mixing ratio (**) Class
(*)
Nominal cover-age (*)
Workability (***)
Ready for use(***)
Installation(*)
For situations in which a
normal setting adhesives is
recommended
MAPEI
50x50; 100x40; 100x50
KERAFLEX MAXI S1
If levelling is necessary, on the above mentioned
supports, apply the following product beforehand
ECOPRIM GRIP
1 bag (25 kg) + 7,2/7,7 litres of
waterC2 TE S1
7 m2
8 hours 14 days
Installation with a double layer of adhesive
ULTRALITE S11 bag (15 kg) + 8,4/8,7 litres of
waterC2 TE S1
100x100; 300x100
ULTRALITE S21 bag (15 kg) + 5,9/6,2 litres of
waterC2 E S2 6,3 m2
KERABOND + ISOLASTIC
1 bag (25 kg) + 8,5 kg of ISOLA-
STICC2 E S2 6,5 m2
KERAKOLL All sizes H40 NO LIMITS Not necessary, according to manufacturer
Grey 1 bag (25 kg) from 7,1 to
8,8 litres of waterC2 TE S1 6 m2 20 hours 3 days
White 1 bag (25 kg) from 7,2 to
9,5 litres of water
LATICRETE All sizes LATICRETE 254 Platinum
Not necessary, according to manufacturer
1 bag (25 kg) + 6 litres of water C2 TE S1 5 m2 1 day 7 days
LITOKOL
50x50;100x40; 100x50 SUPERFLEX K77
Not necessary, according to manufacturer
1 bag (25 kg) + 8,5 litres of water C2 TE S1 6 m2
8 hours 7 days100x100; 300x100
CEMENTKOL K21 + LATEXKOL
1 bag (25 kg) + 7,5 kg of LATEXKOL C2 S2 5 m2
PCI - BASF All sizes PCI NANOLIGHT + PCI LASTOFLEX
On non-absorbent supportsPCI GISOGRUN 303
1 bag (15 kg) + 1 can of PCI
LASTOFLEX (4 kg) + 5 litres of water
C2 TE S2 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBERAll sizes WEBER.COL PRO
HP + WEBER L50
For old ceramic tile, marble slabs and stone:
WEBER. FLOOR 4716 Prime
1 bag (15 kg) + 7 litres of WEBER
L50C2 TE S2 5 m2 8 hours 14 days
ARDEX All sizesARDEX X 77
microtec + ARDEX E 90
As an alternative for old ceramic tile, marble slabs and stone:- ARDEX P 4 -
ARDEX X 77 (rough levelled)
1 bag (25 kg) + 1 can of ARDEX E 90 (4,5 kg) + 9 litres
of water
C2 T(T)E(E) S2 10 m2 8 hours 1 day
Installation with a single layer of adhesive (6 mm
trowel)
For situations in which a
quick setting adhesive is
recommended
MAPEI
50x50; 100x40; 100x50
GRANIRAPID
If levelling is necessary, on the above mentioned supports, apply ECOPRIM
GRIP beforehand
Component A: 1 bag (25 kg)
Component B: tub (5,5 kg)
C2 F S1
6 m2
3 hours 1 day
Installation with a double layer of adhesive
ULTRALITE S1 QUICK 1 bag (15 kg) +
5,1/5,7 litres of water
C2 FTE S1
100x100; 300x100
ULTRALITE S2 QUICK C2 FE S2 7 m2
ELASTORAPID
Component A: 1 bag (25 kg)
Component B: tub (6,5 kg)
C2 FTE S2 6 m2
KERAKOLL All sizes H40 ECO RAPIDFLEX
Not necessary, according to manufacturer
1 bag (25 kg) + 6,3 litres of water
C2F TE S1 6 m2 3 hours 2 days
LATICRETE All sizes
LATICRETE 335 Rapid Super Flex + LATICRETE 282
Latex Additive
Not necessary, according to manufacturer
1 bag (25 kg) + 6/7 litres of latex C2 TE F 5 m2 6 hours 2 days
LITOKOL
50x50;100x40; 100x50
LITOSTONE K99 + LATEXKOL + water For gypsum-based surfaces:
Primer C
1 bag (25 kg) + 3,5 litres of LATEXKOL
+ 3,5 litres of water
C2 FE S15 m2 4 hours 1 day
100x100; 300x100
LITOSTONE K99 + LATEXKOL
1 bag (25 kg) + 7,5 kg of LATEXKOL C2 FE S2
PCI - BASF All sizes PCI NANOLIGHT + PCI LASTOFLEX
On non-absorbent supportsPCI GISOGRUN 303
1 bag (15 kg) + 1 can of PCI
LASTOFLEX (4 kg) + 5 litres of water
C2 TE S2 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBER
50x50; 100x40; 100x50; 100x100
WEBER.COL PRO MARMO + WEBER
L50 For old ceramic tile, marble slabs and stone:
WEBER. FLOOR 4716 Prime
1 bag (25 kg)+ 7 litres of WEBER L50
C2 FT S1 5 m2 4 hours 3 days
WEBER.COL PRO RAPID + WEBER
L50
1 bag (25 kg)+ 6-6,5 litres of
WEBER L50
ARDEX All sizesARDEX X 77 S
microtec + ARDEX E 90
As an alternative for old ceramic tile, marble slabs and stone:- ARDEX P 4 -
ARDEX X 77 (rough levelled)
1 bag (25 kg) + 3 kg of ARDEX E 90 + 7,5 litres of
water
C2 FT(T)E S2 10 m2 90 min. 6 hours
Installation with a single layer of adhesive (6 mm
trowel)
Odpowiedzial-ność instalatora
w sytuacjach kiedy normalne
kleje są polecane
Producent Produkt(*)Rozmiar płyt (cm) Podkład, jeśli konieczny
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Wymagane jest użycie pro-duktu: PCI GISOGRUN 303
Wymagane jest użycie pro-duktu: PCI GISOGRUN 303
Proporcje mieszania (**)
Klasa (*)
nominalne pokrycie
(*)
możliwość obróbki
(***)
gotowe do użycia (***)
montaż (*)
Instrukcje podane bezpośrednio przez producentów, którzy gwarantują poprawność informacji. Po więcej szczegółów, skontaktuj się ze wsparciem technicznym odpowiednich producentów (zobacz “9 - Przydatne kontakty”) “.
Instrukcje podane bezpośrednio przez producentów, którzy gwarantują poprawność informacji. Jeśli produkt jest oferowany zarówno w wersjach “biały” i “szary” , proporcje mieszania mogą się różnić. Po więcej szczegółów, skontaktuj się ze wsparciem technicznym odpowiednich producentów (zobacz “9 - Przydatne kontakty”) “.
Instrukcje podane bezpośrednio przez producentów, którzy gwarantują poprawność informacji. Na podstawie badań laboratoryjnych przeprowadzonych w temperaturze 23 ° C i przy wilgotności względnej 50%. W przypadku zastosowania w innych sytuacjach lub w celu uzyskania więcej szczegółów, skontaktuj się ze wsparciem technicznym odpowiednich producentów (zobacz “9 - Przydatne kontakty”) “.
materiał podłoża: płyta wiórowa, metal
a.2c- KERLITE 3plus i KERLITE 5plus- montaż na ścianie we wnętrzach
1 paczka (15 kg) + 5,1/5,7 litra wody
1 paczka (15 kg) + 1 puszka PCI
LASTOFLEX (4 kg) + 5 litrów wody
1 paczka (15 kg) + 1 puszka PCI
LASTOFLEX (4 kg) + 5 litrów wody
1 paczka (25 kg) + 1 puszka ARDEX E90 (4,5 kg) + 9
litrów wody
1 paczka (25 kg) + ARDEX E90 3kg +
7,5 litrów wody
1 paczka (25 kg) + 1 puszka ARDEX E90 (4,5 kg) + 9
litrów wody
1 wiadro (8kg)
1 wiadro (10 kg)
1 wiadro (10 kg)
1 wiadro (10 kg)
1 wiadro (10 kg)
1 puszka (10 kg)
20 godzin
12 godzin
12 godzin
1 dzień
1 dzień
1 dzień
2 dni
2 dni
2 dni
7 dni
1 dzień
1 dzień
1 dzień
6 godzin
3 godziny
3 godziny
3 godziny
90 min
8 godzin
12 godzin
3 dni
2 dni
3 dni
Montaż z podwójną warstwą kleju
Montaż z podwójną warstwą kleju
Montaż z pojedyńczą warstwą kleju (kielnia 6 mm)
Montaż z pojedyńczą warstwą kleju (kielnia 6 mm)
Montaż z pojedyńczą warstwą kleju (kielnia 6 mm)
Montaż z pojedyńczą warstwą kleju (kielnia 6 mm)
7 dni
7 dni
5 dni
8 godzin
8 godzin
12 godzin
12 godzin
1 szara paczka (25 kg) + 7,1-8,8 litrów wody
1 biała paczka (25 kg) + 7,2-9,5 litrów wody
1 wiadro komponentu A (5 kg) + 1 wiadro
komponentu B (2 kg)
1 wiadro komponentu A (5 kg) + 1 wiadro
komponentu B (2 kg)
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
w sytuacjach kiedy szybkow-iążące kleje są
polecane
44 4544 45
KERLITE Cotto d’Este > KERLITE Technical Manual
Supporting material: concrete
A.3b - Wall installation in exteriors of KERLITE 3mm
(*) Instructions provided directly by manufacturers, who guarantee the information given. For explanations or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
(**) Instructions provided directly by manufacturers, who guarantee the information given. If a product is offered in both "white" and a "grey" versions, the mixing ratio may vary. For explana-tions or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
(***) Ratings provided directly by manufacturers, that guarantee the information given, based on laboratory tests performed at 23° C and with a relative humidity of 50%. For use in different situations, contact the technical support office of the respective manufacturers. For explanations or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
Supporting material: plaster
A.3a - Wall installation in exteriors of KERLITE 3mm
(*) Instructions provided directly by manufacturers, who guarantee the information given. For explanations or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
(**) Instructions provided directly by manufacturers, who guarantee the information given. If a product is offered in both "white" and a "grey" versions, the mixing ratio may vary. For explana-tions or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
(***) Ratings provided directly by manufacturers, that guarantee the information given, based on laboratory tests performed at 23° C and with a relative humidity of 50%. For use in different situations, contact the technical support office of the respective manufacturers. For explanations or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
At the discretion
of I.S.
Manufac-turer
Size of slabs(cm)
Product(*)
Primer, if necessary(*) Mixing ratio (**) Class
(*)
Nominal cover-age (*)
Workability (***)
Ready for use(***)
Installation(*)
For situations in which a
normal setting adhesives is
recommended
MAPEI
50x50; 100x40; 100x50
KERAFLEX MAXI S1
Not necessary, according to manufacturer
1 bag (25 kg) + 7,2/7,7 litres of
waterC2 TE S1
7 m2
8 hours 14 days
Installation with a double layer of adhesive
ULTRALITE S11 bag (15 kg) + 8,4/8,7 litres of
waterC2 TE S1
100x100
ULTRALITE S21 bag (15 kg) + 5,9/6,2 litres of
waterC2 E S2 6,3 m2
KERABOND + ISOLASTIC
1 bag (25 kg) + 8,5 kg of ISOLA-
STICC2 E S2 6,5 m2
KERAKOLL
50x50; 100x40; 100x50
H40 NO LIMITS Not necessary, according to manufacturer
Grey 1 bag (25 kg) from 7,1 to
8,8 litres of water C2 TE S1
6 m2 20 hours 3 days
White 1 bag (25 kg) from 7,2 to
9,5 litres of water1 bag (25 kg)
water and TOP LATEX ECO as indicated by
manufacturer
C2 TE S2100x100
LATICRETE 50x50; 100x40; 100x50; 100x100
LATICRETE 254 Platinum
Not necessary, according to manufacturer
1 bag (25 kg) + 6 litres of water C2 TE S1 5 m2 1 day 7 days
LITOKOL
50x50; 100x40; 100x50 SUPERFLEX K77
Not necessary, according to manufacturer
1 bag (25 kg) + 8,5 litres of water C2 TE S1 6 m2
8 hours 7 days100x100 CEMENTKOL K21 +
LATEXKOL1 bag (25 kg) + 7,5
kg of LATEXKOL C2 S2 5 m2
PCI - BASF 50x50; 100x40; 100x50; 100x100 PCI NANOLIGHT Not necessary, according to
manufacturer1 bag (15 kg) + 9
litres of water C2 TE S1 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBER
50x50; 100x40; 100x50; 100x100
WEBER.COL PRO HP
Not necessary, according to manufacturer
1 bag (25 kg) + 7 litres of water C2 TE S1 5 m2 8 hours 14 days
ARDEX 50x50; 100x40; 100x50; 100x100
ARDEX X 77 microtec
Not necessary, according to manufacturer
1 bag (25 kg) + 11 litres of water
C2 T(T)E(E) S1 10 m2 8 hours 1 day
For situations in which a
quick setting adhesive is
recommended
MAPEI
50x50; 100x40; 100x50
ELASTORAPID
Not necessary, according to manufacturer
Component A: 1 bag (25 kg)
Component B: tub (6,5 kg)
C2 FTE S2
6 m2
3 hours 1 day
Installation with a double layer of adhesive
ULTRALITE S1 QUICK 1 bag (15 kg) +
5,1/5,7 litres of water
C2 FTE S1
100x100
ULTRALITE S2 QUICK C2 FE S2 7 m2
KERAQUICK + LATEX PLUS
1 bag (25 kg) + 8,5 kg of LATEX PLUS C2 FT S2 5 m2
KERAKOLL
50x50; 100x40; 100x50;
H40 ECO RAPIDFLEX
Not necessary, according to manufacturer
1 bag (25 kg) + 6,3 litres of water
C2F TE S1
6 m2 3 hours 2 days
100x100
1 bag (25 kg) water and TOP LATEX ECO as indicated by
manufacturer
C2F TE S2
LATICRETE 50x50; 100x40; 100x50; 100x100
LATICRETE 335 Rapid Super Flex + LATICRETE 282
Latex Additive
Not necessary, according to manufacturer
1 bag (25 kg) + 6/7 litres of latex C2 TE F 5 m2 6 hours 2 days
LITOKOL
50x50; 100x40; 100x50
LITOSTONE K99 + LATEXKOL + water Not necessary, according to
manufacturer
1 bag (25 kg) + 3,5 litres of LATEXKOL + 3,5 litres of water
C2 FE S1
5 m2 4 hours 1 day
100x100 LITOSTONE K99 + LATEXKOL
1 bag (25 kg) + 7,5 kg of LATEXKOL C2 FE S2
PCI - BASF 50x50; 100x40; 100x50; 100x100 PCI NANOLIGHT Not necessary, according to
manufacturer1 bag (15 kg) + 9
litres of water C2 TE S1 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBER
50x50; 100x40; 100x50; 100x100
WEBER.COL PRO MARMO + WEBER
L50 Not necessary, according to manufacturer
1 bag (25 kg)+ 7 litres of WEBER L50
C2 FT S1 5 m2 4 hours 3 days
WEBER.COL PRO RAPID + WEBER
L50
1 bag (25 kg)+ 6-6,5 litres of
WEBER L50
ARDEX 50x50; 100x40; 100x50; 100x100
ARDEX X 77 S microtec
Not necessary, according to manufacturer
1 bag (25 kg) + 8,5 litres of water
C2 FT(T)E S1 10 m2 90 min. 6 hours
At the discretion of I.S.
Manufac-turer
Size of slabs(cm)
Product(*)
Primer, if necessary(*) Mixing ratio (**) Class
(*)Nominal
coverage (*)Workability
(***)
Ready for use(***)
Installation(*)
For situations in which a
normal setting adhesives is
recommended
MAPEI
50x50; 100x40; 100x50
KERAFLEX MAXI S1
Not necessary, according to manufacturer
1 bag (25 kg) + 7,2/7,7 litres of
waterC2 TE S1
7 m2
8 hours 14 days
Installation with a double layer of adhesive
ULTRALITE S11 bag (15 kg) + 8,4/8,7 litres of
waterC2 TE S1
100x100
ULTRALITE S21 bag (15 kg) + 5,9/6,2 litres of
waterC2 E S2 6,3 m2
KERABOND + ISOLASTIC
1 bag (25 kg) + 8,5 kg of ISOLASTIC
C2 E S2 6,5 m2
KERAKOLL
50x50; 100x40; 100x50
H40 NO LIMITS Not necessary, according to manufacturer
Grey 1 bag (25 kg) from 7,1 to
8,8 litres of waterC2 TE S1
6 m2 20 hours 3 days
White 1 bag (25 kg) from 7,2 to
9,5 litres of water
1 bag (25 kg) water and TOP LATEX
ECO as indicated by manufacturer
C2 TE S2100x100
LITOKOL
50x50; 100x40; 100x50 SUPERFLEX K77
Not necessary, according to manufacturer
1 bag (25 kg) + 8,5 litres of water C2 TE S1 6 m2
8 hours 7 days100x100 CEMENTKOL K21 +
LATEXKOL1 bag (25 kg) + 7,5
kg of LATEXKOL C2 S2 5 m2
PCI - BASF 50x50; 100x40; 100x50; 100x100 PCI NANOLIGHT Not necessary, according to
manufacturer1 bag (15 kg) + 9
litres of water C2 TE S1 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBER
50x50; 100x40; 100x50; 100x100
WEBER.COL PRO HP + WEBER L50
Not necessary, according to manufacturer
1 bag (15 kg) + 7 litres of WEBER
L50C2 TE S2 5 m2 8 hours 14 days
ARDEX 50x50; 100x40; 100x50; 100x100
ARDEX X 77 microtec
Not necessary, according to manufacturer
1 bag (25 kg) + 11 litres of water
C2 T(T)E(E) S1 10 m2 8 hours 1 day
For situations in which a
quick setting adhesive is
recommended
MAPEI
50x50; 100x40; 100x50
ELASTORAPID
Not necessary, according to manufacturer
Component A: 1 bag (25 kg)
Component B: tub (6,5 kg)
C2 FTE S2
6 m2
3 hours 1 day
Installation with a double layer of adhesive
ULTRALITE S1 QUICK
1 bag (15 kg) + 5,1/5,7 litres of
water
C2 FTE S1
100x100
ULTRALITE S2 QUICK
1 bag (15 kg) + 5,1/5,7 litres of
waterC2 FE S2 7 m2
KERAQUICK + LATEX PLUS
1 bag (25 kg) + 8,5 kg of LATEX PLUS C2 FT S2 5 m2
KERAKOLL
50x50; 100x40; 100x50;
H40 ECO RAPIDFLEX
Not necessary, according to manufacturer
1 bag (25 kg) + 6,3 litres of water
C2F TE S1
6 m2 3 hours 2 days100x100
1 bag (25 kg) water and TOP LATEX
ECO as indicated by manufacturer
C2F TE S2
LATICRETE 50x50; 100x40; 100x50; 100x100
LATICRETE 335 Rapid Super Flex + LATICRETE 282
Latex Additive
Not necessary, according to manufacturer
1 bag (25 kg) + 6/7 litres of latex C2 TE F 5 m2 6 hours 2 days
LITOKOL
50x50; 100x40; 100x50
LITOSTONE K99 + LATEXKOL + water Not necessary, according to
manufacturer
1 bag (25 kg) + 3,5 litres of LATEXKOL + 3,5 litres of water
C2 FE S1
5 m2 4 hours 1 day
100x100 LITOSTONE K99 + LATEXKOL
1 bag (25 kg) + 7,5 kg of LATEXKOL C2 FE S2
PCI - BASF 50x50; 100x40; 100x50; 100x100 PCI NANOLIGHT Not necessary, according to
manufacturer1 bag (15 kg) + 9
litres of water C2 TE S1 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBER
50x50; 100x40; 100x50; 100x100
WEBER.COL PRO MARMO + WEBER
L50 Not necessary, according to manufacturer
1 bag (25 kg)+ 7 litres of WEBER L50
C2 FT S1 5 m2 4 hours 3 days
WEBER.COL PRO RAPID + WEBER
L50
1 bag (25 kg)+ 6-6,5 litres of
WEBER L50
ARDEX 50x50; 100x40; 100x50; 100x100
ARDEX X 77 S microtec
Not necessary, according to manufacturer
1 bag (25 kg) + 8,5 litres of water
C2 FT(T)E S1 10 m2 90 min. 6 hours
Odpowiedzial-ność instalatora
w sytuacjach kiedy normalne
kleje są polecane
Producent Produkt(*)Rozmiar płyt (cm) Podkład, jeśli konieczny
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Proporcje mieszania (**)
Klasa (*)
nominalne pokrycie
(*)
możliwość obróbki
(***)
gotowe do użycia (***)
montaż (*)
Instrukcje podane bezpośrednio przez producentów, którzy gwarantują poprawność informacji. Po więcej szczegółów, skontaktuj się ze wsparciem technicznym odpowiednich producentów (zobacz “9 - Przydatne kontakty”) “.
Instrukcje podane bezpośrednio przez producentów, którzy gwarantują poprawność informacji. Jeśli produkt jest oferowany zarówno w wersjach “biały” i “szary” , proporcje mieszania mogą się różnić. Po więcej szczegółów, skontaktuj się ze wsparciem technicznym odpowiednich producentów (zobacz “9 - Przydatne kontakty”) “.
Instrukcje podane bezpośrednio przez producentów, którzy gwarantują poprawność informacji. Na podstawie badań laboratoryjnych przeprowadzonych w temperaturze 23 ° C i przy wilgotności względnej 50%. W przypadku zastosowania w innych sytuacjach lub w celu uzyskania więcej szczegółów, skontaktuj się ze wsparciem technicznym odpowiednich producentów (zobacz “9 - Przydatne kontakty”) “.
a.3a - KERLITE 3mm - montaż na ścianie na zewnątrz
materiał podłoża: gips
1 paczka (25 kg) + 8,5 litra wody
1 paczka (25 kg) + 6-6,5 litra
WEBER L50
1 paczka (25 kg) + 7 litrów
WEBER L50
1 paczka (15 kg) + 9 litrów wody
1 paczka (25 kg) + 3,5 litra LATEXKOL
+ 3,5 litra wody
1 paczka (25 kg) + 7,5 kg LATEXKOL
1 paczka (25 kg) + 6/7 litrów latexu
1 paczka (25 kg) + 6,3 litra wody
1 paczka (25 kg); woda i TOP LATEX ECO jak zalecane przez producenta
1 paczka (15 kg) + 5,1/5,7 litra wody
1 paczka (25 kg) + 11 litrów wody
1 paczka (25 kg) + 7 litrów wody
1 paczka (15 kg) + 9 litrów wody
1 paczka (25 kg) + 8,5 litra wody
1 paczka (25 kg) + 6 litrów wody
1 paczka (25 kg); woda i TOP LATEX
ECO jak zalececane przez producenta
1 szara paczka (25 kg) 7,2 - 9,5 litra
1 paczka (25 kg) + 8,5 kg ISOLASTIC
1 paczka (15 kg) + 5,9/6,2 litra wody
1 paczka (25 kg) + 7,2/7,7 litra wody
1 paczka (15 kg) + 8,4/8,7 litra wody
8 godzin
20 godzin
1 dzień
1 dzień1 dzień
1 dzień
1 dzień
1 dzień
1 dzień
2 dni
2 dni
3 dni
6 godzin
4 godziny
3 godziny
3 godziny
90 min
4 godziny
6 godzin
8 godzin
3 dni Montaż z podwójną warstwą kleju
Montaż z podwójną warstwą kleju
14 dni
14 dni
14 dni1 dzień
8 godzin 7 dni
8 godzin
8 godzin
1 szara paczka (25 kg) + 7,1 - 8,8 litrów wody
Komponent A: 1 paczka (25 kg)
Komponent B: opa-kowanie (6,5 kg)
w sytuacjach kiedy szybkow-iążące kleje są
polecane
1 paczka (25 kg) + 7,5 kg LATEXKOL
44 4544 45
KERLITE Cotto d’Este > KERLITE Technical Manual
Supporting material: concrete
A.3b - Wall installation in exteriors of KERLITE 3mm
(*) Instructions provided directly by manufacturers, who guarantee the information given. For explanations or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
(**) Instructions provided directly by manufacturers, who guarantee the information given. If a product is offered in both "white" and a "grey" versions, the mixing ratio may vary. For explana-tions or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
(***) Ratings provided directly by manufacturers, that guarantee the information given, based on laboratory tests performed at 23° C and with a relative humidity of 50%. For use in different situations, contact the technical support office of the respective manufacturers. For explanations or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
Supporting material: plaster
A.3a - Wall installation in exteriors of KERLITE 3mm
(*) Instructions provided directly by manufacturers, who guarantee the information given. For explanations or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
(**) Instructions provided directly by manufacturers, who guarantee the information given. If a product is offered in both "white" and a "grey" versions, the mixing ratio may vary. For explana-tions or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
(***) Ratings provided directly by manufacturers, that guarantee the information given, based on laboratory tests performed at 23° C and with a relative humidity of 50%. For use in different situations, contact the technical support office of the respective manufacturers. For explanations or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
At the discretion
of I.S.
Manufac-turer
Size of slabs(cm)
Product(*)
Primer, if necessary(*) Mixing ratio (**) Class
(*)
Nominal cover-age (*)
Workability (***)
Ready for use(***)
Installation(*)
For situations in which a
normal setting adhesives is
recommended
MAPEI
50x50; 100x40; 100x50
KERAFLEX MAXI S1
Not necessary, according to manufacturer
1 bag (25 kg) + 7,2/7,7 litres of
waterC2 TE S1
7 m2
8 hours 14 days
Installation with a double layer of adhesive
ULTRALITE S11 bag (15 kg) + 8,4/8,7 litres of
waterC2 TE S1
100x100
ULTRALITE S21 bag (15 kg) + 5,9/6,2 litres of
waterC2 E S2 6,3 m2
KERABOND + ISOLASTIC
1 bag (25 kg) + 8,5 kg of ISOLA-
STICC2 E S2 6,5 m2
KERAKOLL
50x50; 100x40; 100x50
H40 NO LIMITS Not necessary, according to manufacturer
Grey 1 bag (25 kg) from 7,1 to
8,8 litres of water C2 TE S1
6 m2 20 hours 3 days
White 1 bag (25 kg) from 7,2 to
9,5 litres of water1 bag (25 kg)
water and TOP LATEX ECO as indicated by
manufacturer
C2 TE S2100x100
LATICRETE 50x50; 100x40; 100x50; 100x100
LATICRETE 254 Platinum
Not necessary, according to manufacturer
1 bag (25 kg) + 6 litres of water C2 TE S1 5 m2 1 day 7 days
LITOKOL
50x50; 100x40; 100x50 SUPERFLEX K77
Not necessary, according to manufacturer
1 bag (25 kg) + 8,5 litres of water C2 TE S1 6 m2
8 hours 7 days100x100 CEMENTKOL K21 +
LATEXKOL1 bag (25 kg) + 7,5
kg of LATEXKOL C2 S2 5 m2
PCI - BASF 50x50; 100x40; 100x50; 100x100 PCI NANOLIGHT Not necessary, according to
manufacturer1 bag (15 kg) + 9
litres of water C2 TE S1 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBER
50x50; 100x40; 100x50; 100x100
WEBER.COL PRO HP
Not necessary, according to manufacturer
1 bag (25 kg) + 7 litres of water C2 TE S1 5 m2 8 hours 14 days
ARDEX 50x50; 100x40; 100x50; 100x100
ARDEX X 77 microtec
Not necessary, according to manufacturer
1 bag (25 kg) + 11 litres of water
C2 T(T)E(E) S1 10 m2 8 hours 1 day
For situations in which a
quick setting adhesive is
recommended
MAPEI
50x50; 100x40; 100x50
ELASTORAPID
Not necessary, according to manufacturer
Component A: 1 bag (25 kg)
Component B: tub (6,5 kg)
C2 FTE S2
6 m2
3 hours 1 day
Installation with a double layer of adhesive
ULTRALITE S1 QUICK 1 bag (15 kg) +
5,1/5,7 litres of water
C2 FTE S1
100x100
ULTRALITE S2 QUICK C2 FE S2 7 m2
KERAQUICK + LATEX PLUS
1 bag (25 kg) + 8,5 kg of LATEX PLUS C2 FT S2 5 m2
KERAKOLL
50x50; 100x40; 100x50;
H40 ECO RAPIDFLEX
Not necessary, according to manufacturer
1 bag (25 kg) + 6,3 litres of water
C2F TE S1
6 m2 3 hours 2 days
100x100
1 bag (25 kg) water and TOP LATEX ECO as indicated by
manufacturer
C2F TE S2
LATICRETE 50x50; 100x40; 100x50; 100x100
LATICRETE 335 Rapid Super Flex + LATICRETE 282
Latex Additive
Not necessary, according to manufacturer
1 bag (25 kg) + 6/7 litres of latex C2 TE F 5 m2 6 hours 2 days
LITOKOL
50x50; 100x40; 100x50
LITOSTONE K99 + LATEXKOL + water Not necessary, according to
manufacturer
1 bag (25 kg) + 3,5 litres of LATEXKOL + 3,5 litres of water
C2 FE S1
5 m2 4 hours 1 day
100x100 LITOSTONE K99 + LATEXKOL
1 bag (25 kg) + 7,5 kg of LATEXKOL C2 FE S2
PCI - BASF 50x50; 100x40; 100x50; 100x100 PCI NANOLIGHT Not necessary, according to
manufacturer1 bag (15 kg) + 9
litres of water C2 TE S1 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBER
50x50; 100x40; 100x50; 100x100
WEBER.COL PRO MARMO + WEBER
L50 Not necessary, according to manufacturer
1 bag (25 kg)+ 7 litres of WEBER L50
C2 FT S1 5 m2 4 hours 3 days
WEBER.COL PRO RAPID + WEBER
L50
1 bag (25 kg)+ 6-6,5 litres of
WEBER L50
ARDEX 50x50; 100x40; 100x50; 100x100
ARDEX X 77 S microtec
Not necessary, according to manufacturer
1 bag (25 kg) + 8,5 litres of water
C2 FT(T)E S1 10 m2 90 min. 6 hours
At the discretion of I.S.
Manufac-turer
Size of slabs(cm)
Product(*)
Primer, if necessary(*) Mixing ratio (**) Class
(*)Nominal
coverage (*)Workability
(***)
Ready for use(***)
Installation(*)
For situations in which a
normal setting adhesives is
recommended
MAPEI
50x50; 100x40; 100x50
KERAFLEX MAXI S1
Not necessary, according to manufacturer
1 bag (25 kg) + 7,2/7,7 litres of
waterC2 TE S1
7 m2
8 hours 14 days
Installation with a double layer of adhesive
ULTRALITE S11 bag (15 kg) + 8,4/8,7 litres of
waterC2 TE S1
100x100
ULTRALITE S21 bag (15 kg) + 5,9/6,2 litres of
waterC2 E S2 6,3 m2
KERABOND + ISOLASTIC
1 bag (25 kg) + 8,5 kg of ISOLASTIC
C2 E S2 6,5 m2
KERAKOLL
50x50; 100x40; 100x50
H40 NO LIMITS Not necessary, according to manufacturer
Grey 1 bag (25 kg) from 7,1 to
8,8 litres of waterC2 TE S1
6 m2 20 hours 3 days
White 1 bag (25 kg) from 7,2 to
9,5 litres of water
1 bag (25 kg) water and TOP LATEX
ECO as indicated by manufacturer
C2 TE S2100x100
LITOKOL
50x50; 100x40; 100x50 SUPERFLEX K77
Not necessary, according to manufacturer
1 bag (25 kg) + 8,5 litres of water C2 TE S1 6 m2
8 hours 7 days100x100 CEMENTKOL K21 +
LATEXKOL1 bag (25 kg) + 7,5
kg of LATEXKOL C2 S2 5 m2
PCI - BASF 50x50; 100x40; 100x50; 100x100 PCI NANOLIGHT Not necessary, according to
manufacturer1 bag (15 kg) + 9
litres of water C2 TE S1 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBER
50x50; 100x40; 100x50; 100x100
WEBER.COL PRO HP + WEBER L50
Not necessary, according to manufacturer
1 bag (15 kg) + 7 litres of WEBER
L50C2 TE S2 5 m2 8 hours 14 days
ARDEX 50x50; 100x40; 100x50; 100x100
ARDEX X 77 microtec
Not necessary, according to manufacturer
1 bag (25 kg) + 11 litres of water
C2 T(T)E(E) S1 10 m2 8 hours 1 day
For situations in which a
quick setting adhesive is
recommended
MAPEI
50x50; 100x40; 100x50
ELASTORAPID
Not necessary, according to manufacturer
Component A: 1 bag (25 kg)
Component B: tub (6,5 kg)
C2 FTE S2
6 m2
3 hours 1 day
Installation with a double layer of adhesive
ULTRALITE S1 QUICK
1 bag (15 kg) + 5,1/5,7 litres of
water
C2 FTE S1
100x100
ULTRALITE S2 QUICK
1 bag (15 kg) + 5,1/5,7 litres of
waterC2 FE S2 7 m2
KERAQUICK + LATEX PLUS
1 bag (25 kg) + 8,5 kg of LATEX PLUS C2 FT S2 5 m2
KERAKOLL
50x50; 100x40; 100x50;
H40 ECO RAPIDFLEX
Not necessary, according to manufacturer
1 bag (25 kg) + 6,3 litres of water
C2F TE S1
6 m2 3 hours 2 days100x100
1 bag (25 kg) water and TOP LATEX
ECO as indicated by manufacturer
C2F TE S2
LATICRETE 50x50; 100x40; 100x50; 100x100
LATICRETE 335 Rapid Super Flex + LATICRETE 282
Latex Additive
Not necessary, according to manufacturer
1 bag (25 kg) + 6/7 litres of latex C2 TE F 5 m2 6 hours 2 days
LITOKOL
50x50; 100x40; 100x50
LITOSTONE K99 + LATEXKOL + water Not necessary, according to
manufacturer
1 bag (25 kg) + 3,5 litres of LATEXKOL + 3,5 litres of water
C2 FE S1
5 m2 4 hours 1 day
100x100 LITOSTONE K99 + LATEXKOL
1 bag (25 kg) + 7,5 kg of LATEXKOL C2 FE S2
PCI - BASF 50x50; 100x40; 100x50; 100x100 PCI NANOLIGHT Not necessary, according to
manufacturer1 bag (15 kg) + 9
litres of water C2 TE S1 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBER
50x50; 100x40; 100x50; 100x100
WEBER.COL PRO MARMO + WEBER
L50 Not necessary, according to manufacturer
1 bag (25 kg)+ 7 litres of WEBER L50
C2 FT S1 5 m2 4 hours 3 days
WEBER.COL PRO RAPID + WEBER
L50
1 bag (25 kg)+ 6-6,5 litres of
WEBER L50
ARDEX 50x50; 100x40; 100x50; 100x100
ARDEX X 77 S microtec
Not necessary, according to manufacturer
1 bag (25 kg) + 8,5 litres of water
C2 FT(T)E S1 10 m2 90 min. 6 hours
materiał podłoża: beton
a.3b - KERLITE 3mm - montaż na ścianie na zewnątrz
Odpowiedzial-ność instalatora
w sytuacjach kiedy normalne
kleje są polecane
Producent Produkt(*)Rozmiar płyt (cm) Podkład, jeśli konieczny
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Proporcje mieszania (**)
Klasa (*)
nominalne pokrycie
(*)
możliwość obróbki
(***)
gotowe do użycia (***)
montaż (*)
Instrukcje podane bezpośrednio przez producentów, którzy gwarantują poprawność informacji. Po więcej szczegółów, skontaktuj się ze wsparciem technicznym odpowiednich producentów (zobacz “9 - Przydatne kontakty”) “.
Instrukcje podane bezpośrednio przez producentów, którzy gwarantują poprawność informacji. Jeśli produkt jest oferowany zarówno w wersjach “biały” i “szary” , proporcje mieszania mogą się różnić. Po więcej szczegółów, skontaktuj się ze wsparciem technicznym odpowiednich producentów (zobacz “9 - Przydatne kontakty”) “.
Instrukcje podane bezpośrednio przez producentów, którzy gwarantują poprawność informacji. Na podstawie badań laboratoryjnych przeprowadzonych w temperaturze 23 ° C i przy wilgotności względnej 50%. W przypadku zastosowania w innych sytuacjach lub w celu uzyskania więcej szczegółów, skontaktuj się ze wsparciem technicznym odpowiednich producentów (zobacz “9 - Przydatne kontakty”) “.
1 paczka (25 kg) + 8,5 litra wody
1 paczka (25 kg) + 6-6,5 litra
WEBER L50
1 paczka (25 kg) + 7 litrów
WEBER L50
1 paczka (15 kg) + 9 litrów wody
1 paczka (25 kg) + 3,5 litra LATEXKOL
+ 3,5 litra wody
1 paczka (25 kg) + 7,5 kg LATEXKOL
1 paczka (25 kg) + 6/7 litrów latexu
1 paczka (25 kg) + 6,3 litra wody
1 paczka (25 kg); woda i TOP LATEX ECO jak zalecane przez producenta
1 paczka (15 kg) + 5,1/5,7 litra wody
1 paczka (15 kg) + 5,1/5,7 litra wody
1 paczka (25 kg) + 7 litrów wody
1 paczka (15 kg) + 9 litrów wody
1 paczka (25 kg) + 8,5 litra wody
1 paczka (25 kg) + 6 litrów wody
1 paczka (25 kg); woda i TOP LATEX
ECO jak zalececane przez producenta
1 szara paczka (25 kg) 7,2 - 9,5 litra
1 paczka (25 kg) + 8,5 kg ISOLASTIC
1 paczka (15 kg) + 5,9/6,2 litra wody
1 paczka (25 kg) + 7,2/7,7 litra wody
1 paczka (15 kg) + 8,4/8,7 litra wody
8 godzin
20 godzin
1 dzień1 dzień
1 dzień
1 dzień
1 dzień
1 dzień
2 dni
2 dni
3 dni
6 godzin
4 godziny
3 godziny
3 godziny
90 min
4 godziny
6 godzin
8 godzin
3 dni Montaż z podwójną warstwą kleju
Montaż z podwójną warstwą kleju
14 dni
14 dni1 dzień
8 godzin 7 dni
8 godzin
8 godzin
1 szara paczka (25 kg) + 7,1 - 8,8 litrów wody
Komponent A: 1 paczka (25 kg)
Komponent B: opa-kowanie (6,5 kg)
w sytuacjach kiedy szybkow-iążące kleje są
polecane
1 paczka (25 kg) + 7,5 kg LATEXKOL
46 4746 47
KERLITE Cotto d’Este > KERLITE Technical Manual
Supporting material: concrete
A.4b - Wall installation in exteriors of KERLITE 3plus and KERLITE 5plus
At the discretion
of I.S.
Manufac-turer
Size of slabs(cm)
Product(*)
Primer, if necessary(*) Mixing ratio (**) Class
(*)
Nominal cover-age (*)
Workability (***)
Ready for use(***)
Installation(*)
For situations in which a
normal setting adhesives is
recommended
MAPEI
50x50; 100x40; 100x50
KERABOND + ISOLASTIC
Not necessary, according to manufacturer
1 bag (25 kg) + 8,5 kg of ISOLASTIC C2 E S2 5 m2
8 hours 14 days
Installation with a double layer of adhesive
ULTRALITE S21 bag (15 kg) + 5,9/6,2 litres of
waterC2 E S2 3 m2
100x100; 300x100 KERALASTIC T 1 can (10 kg) R2T 2,5 m2 12 hours 7 days
KERAKOLL
50x50; 100x40; 100x50
H40 NO LIMITS Not necessary, according to manufacturer
Grey 1 bag (25 kg) from 7,1 to
8,8 litres of waterC2 TE S1
6 m2 20 hours 3 days
White 1 bag (25 kg) from 7,2 to
9,5 litres of water
100x100
1 bag (25 kg) water and TOP LATEX ECO as indicated by
manufacturer
C2 TE S2
LATICRETE All sizes LATICRETE 254 Platinum
Not necessary, according to manufacturer
1 bag (25 kg) + 6 litres of water C2 TE S1 5 m2 1 day 7 days
LITOKOL All sizes CEMENTKOL K21 + LATEXKOL
Not necessary, according to manufacturer
1 bag (25 kg) + 7,5 kg of LATEXKOL C2 S2 5 m2 8 hours 7 days
PCI - BASF All sizes PCI NANOLIGHT + PCI LASTOFLEX
Not necessary, according to manufacturer
1 bag (15 kg) + 1 can of PCI
LASTOFLEX (4 kg) + 6 litres of water
C2 TE S2 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBERAll sizes WEBER.COL PRO
HP + WEBER L50Not necessary, according to
manufacturer
1 bag (15 kg) + 7 litres of WEBER
L50C2 TE S2 5 m2 8 hours 14 days
ARDEX All sizesARDEX X 77
microtec + ARDEX E 90
Not necessary, according to manufacturer
1 bag (25 kg) + 1 can of ARDEX E 90 (4,5 kg) + 9 litres of
water
C2 T(T)E(E) S2 10 m2 8 hours 1 day
For situations in which a
quick setting adhesive is
recommended
MAPEI
50x50; 100x40; 100x50
ULTRALITE S2 QUICK Not necessary, according to
manufacturer
1 bag (15 kg) + 6 litres of water C2 FE S2 4 m2
3 hours2 days
Installation with a double layer of adhesive
100x100; 300x100
KERAQUICK + LATEX PLUS
1 bag (25 kg) + 8,5 kg of LATEX PLUS C2 FT S2 5 m2 1 day
KERAKOLL
50x50; 100x40; 100x50;
H40 ECO RAPIDFLEX
Not necessary, according to manufacturer
1 bag (25 kg) + 6,3 litres of water
C2F TE S1
6 m2 3 hours 2 days100x100
1 bag (25 kg) water and TOP LATEX ECO as indicated by
manufacturer
C2F TE S2
LATICRETE All sizes
LATICRETE 335 Rapid Super Flex + LATICRETE 282
Latex Additive
Not necessary, according to manufacturer
1 bag (25 kg) + 6/7 litres of latex C2 TE F 5 m2 6 hours 2 days
LITOKOL All sizes LITOSTONE K99 + LATEXKOL
Not necessary, according to manufacturer
1 bag (25 kg) + 7,5 kg of LATEXKOL C2 FE S2 5 m2 4 hours 1 day
PCI - BASF All sizes PCI NANOLIGHT + PCI LASTOFLEX
Not necessary, according to manufacturer
1 bag (15 kg) + 1 can of PCI
LASTOFLEX (4 kg) + 6 litres of water
C2 TE S2 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBERAll sizes WEBER.COL.FIX CR Not necessary, according to
manufacturer 1 bucket (10 kg) R2 T 3 m2 12 hours 2 daysInstallation with a single layer of adhesive (6 mm
trowel)
ARDEX All sizesARDEX X 77 S
microtec + ARDEX E 90
Not necessary, according to manufacturer
1 bag (25 kg) + 3 kg of ARDEX E 90 +
7,5 litres of water
C2 FT(T)E S2 10 m2 90 min. 6 hours Installation with a
double layer of adhesive
(*) Instructions provided directly by manufacturers, who guarantee the information given. For explanations or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
(**) Instructions provided directly by manufacturers, who guarantee the information given. If a product is offered in both "white" and a "grey" versions, the mixing ratio may vary. For explana-tions or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
(***) Ratings provided directly by manufacturers, that guarantee the information given, based on laboratory tests performed at 23° C and with a relative humidity of 50%. For use in different situations, contact the technical support office of the respective manufacturers. For explanations or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
Supporting material: plaster
A.4a - Wall installation in exteriors of KERLITE 3plus and KERLITE 5plus
At the discretion
of I.S.
Manufac-turer
Size of slabs(cm)
Product(*)
Primer, if necessary(*) Mixing ratio (**) Class
(*)
Nominal cover-age (*)
Workability (***)
Ready for use(***)
Installation(*)
For situations in which a
normal setting adhesives is
recommended
MAPEI
50x50; 100x40; 100x50
KERABOND + ISOLASTIC
Not necessary, according to manufacturer
1 bag (25 kg) + 8,5 kg of ISOLASTIC C2 E S2 5 m2
8 hours 14 days
Installation with a double layer of adhesive
ULTRALITE S21 bag (15 kg) + 5,9/6,2 litres of
waterC2 E S2 3 m2
100x100; 300x100 KERALASTIC T 1 can (10 kg) R2T 2,5 m2 12 hours 7 days
KERAKOLL
50x50; 100x40; 100x50
H40 NO LIMITS Not necessary, according to manufacturer
Grey 1 bag (25 kg) from 7,1 to
8,8 litres of waterC2 TE S1
6 m2 20 hours 3 days
White 1 bag (25 kg) from 7,2 to
9,5 litres of water
100x100
1 bag (25 kg) water and TOP LATEX ECO as indicated by
manufacturer
C2 TE S2
LATICRETE All sizes LATICRETE 254 Platinum
Not necessary, according to manufacturer
1 bag (25 kg) + 6 litres of water C2 TE S1 5 m2 1 day 7 days
LITOKOL All sizes CEMENTKOL K21 + LATEXKOL
Not necessary, according to manufacturer
1 bag (25 kg) + 7,5 kg of LATEXKOL C2 S2 5 m2 8 hours 7 days
PCI - BASF All sizes PCI NANOLIGHT + PCI LASTOFLEX
Not necessary, according to manufacturer
1 bag (15 kg) + 1 can of PCI
LASTOFLEX (4 kg) + 5 litres of water
C2 TE S2 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBERAll sizes WEBER.COL PRO
HP + WEBER L50Not necessary, according to
manufacturer
1 bag (15 kg) + 7 litres of WEBER
L50C2 TE S2 5 m2 8 hours 14 days
ARDEX All sizesARDEX X 77
microtec + ARDEX E 90
Not necessary, according to manufacturer
1 bag (25 kg) + 1 can of ARDEX E 90 (4,5 kg) + 9 litres of
water
C2 T(T)E(E) S2 10 m2 8 hours 1 day
For situations in which a
quick setting adhesive is
recommended
MAPEI
50x50; 100x40; 100x50
ULTRALITE S2 QUICK
Not necessary, according to manufacturer
1 bag (15 kg) + 6 litres of water C2 FE S2 4 m2
3 hours
2 days
Installation with a double layer of adhesive
100x100; 300x100
KERAQUICK + LATEX PLUS
1 bag (25 kg) + 8,5 kg of LATEX PLUS C2 FT S2 5 m2 1 day
KERAKOLL
50x50; 100x40; 100x50;
H40 ECO RAPIDFLEX
Not necessary, according to manufacturer
1 bag (25 kg) + 6,3 litres of water
C2F TE S1
6 m2 3 hours 2 days
100x100
1 bag (25 kg) water and TOP LATEX ECO as indicated by
manufacturer
C2F TE S2
LATICRETE All sizes
LATICRETE 335 Rapid Super Flex + LATICRETE 282
Latex Additive
Not necessary, according to manufacturer
1 bag (25 kg) + 6/7 litres of latex C2 TE F 5 m2 6 hours 2 days
LITOKOL All sizes LITOSTONE K99 + LATEXKOL
Not necessary, according to manufacturer
1 bag (25 kg) + 7,5 kg of LATEXKOL C2 FE S2 5 m2 4 hours 1 day
PCI - BASF All sizes PCI NANOLIGHT + PCI LASTOFLEX
Not necessary, according to manufacturer
1 bag (15 kg) + 1 can of PCI
LASTOFLEX (4 kg) + 5 litres of water
C2 TE S2 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBER
50x50; 100x40; 100x50; 100x100
WEBER.COL PRO MARMO + WEBER
L50 Not necessary, according to manufacturer
1 bag (25 kg)+ 7 litres of WEBER L50
C2 FT S1 5 m2 4 hours 3 days
WEBER.COL PRO RAPID + WEBER
L50
1 bag (25 kg)+ 6-6,5 litres of
WEBER L50
ARDEX All sizesARDEX X 77 S
microtec + ARDEX E 90
Not necessary, according to manufacturer
1 bag (25 kg) + 3 kg of ARDEX E 90 +
7,5 litres of water
C2 FT(T)E S2 10 m2 90 min. 6 hours
(*) Instructions provided directly by manufacturers, who guarantee the information given. For explanations or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
(**) Instructions provided directly by manufacturers, who guarantee the information given. If a product is offered in both "white" and a "grey" versions, the mixing ratio may vary. For explana-tions or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
(***) Ratings provided directly by manufacturers, that guarantee the information given, based on laboratory tests performed at 23° C and with a relative humidity of 50%. For use in different situations, contact the technical support office of the respective manufacturers. For explanations or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
Odpowiedzial-ność instalatora
w sytuacjach kiedy normalne
kleje są polecane
Producent Produkt(*)Rozmiar płyt (cm) Podkład, jeśli konieczny
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Proporcje mieszania (**)
Klasa (*)
nominalne pokrycie
(*)
możliwość obróbki
(***)
gotowe do użycia (***)
montaż (*)
Instrukcje podane bezpośrednio przez producentów, którzy gwarantują poprawność informacji. Po więcej szczegółów, skontaktuj się ze wsparciem technicznym odpowiednich producentów (zobacz “9 - Przydatne kontakty”) “.
Instrukcje podane bezpośrednio przez producentów, którzy gwarantują poprawność informacji. Jeśli produkt jest oferowany zarówno w wersjach “biały” i “szary” , proporcje mieszania mogą się różnić. Po więcej szczegółów, skontaktuj się ze wsparciem technicznym odpowiednich producentów (zobacz “9 - Przydatne kontakty”) “.
Instrukcje podane bezpośrednio przez producentów, którzy gwarantują poprawność informacji. Na podstawie badań laboratoryjnych przeprowadzonych w temperaturze 23 ° C i przy wilgotności względnej 50%. W przypadku zastosowania w innych sytuacjach lub w celu uzyskania więcej szczegółów, skontaktuj się ze wsparciem technicznym odpowiednich producentów (zobacz “9 - Przydatne kontakty”) “.
a.4a - KERLITE 3plus i KERLITE 5plus - montaż na ścianie na zewnątrz
materiał podłoża: gips
1 paczka (25 kg) + 6 litrów wody
1 paczka (25 kg) + 6,3 litrów wody
1 paczka (15 kg) + 6 litrów wody
1 paczka (25 kg) + 8,5 kg LATEX PLUS
1 paczka (25 kg) + 6/7 litrów latexu
1 paczka (25 kg) + 7,5 kg LATEXKOL
1 paczka (25 kg) + 7,5 kg LATEXKOL
1 paczka (15 kg) + 7 litrów WEBER L50
1 paczka (25 kg) + 7 litrów WEBER L50
1 paczka (25 kg) + 6/6,5 litrów WEBER
1 paczka 25 kg) + 1 puszka ARDEX E 90 (4,5 kg) + 9 litrów
wody
1 paczka 25 kg) + 3kg ARDEX E 90 + 7,5
litrów wody
1 paczka (15 kg) + 1 puszka PCI LASTOF-LEX (4 kg) + 5 litrów
wody
1 paczka (15 kg) + 1 puszka PCI LASTOF-LEX (4 kg) + 5 litrów
wody
1 biała paczka (25 kg) 7,2 - 9,5 litra wody
1 paczka (25 kg) wody i TOP LATEX ECO wg. zaleceń
producenta
1 paczka (25 kg) wody i TOP LATEX ECO wg. zaleceń
producenta
1 paczka (15 kg) + 5,9/6,2 litra wody
1 paczka (25 kg) + 8,5 kg ISOLASTIC
8 godzin
12 godzin
20 godzin
1 dzień
1 dzień
1 dzień
1 dzień
1 dzień
1 dzień
2 dni
2 dni
2 dni
3 dni
6 godzin
4 godziny
3 godziny
3 godziny
90 min
4 godziny
8 godzin
6 godzin
3 dni
Montaż z podwójną warstwą kleju
Montaż z podwójną warstwą kleju
14 dni
7 dni
7 dni
7 dni
14 dni
8 godzin
8 godzin
8 godzin
8 godzin
1 puszka (10 kg)
Wszystkie rozmiaryWszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
w sytuacjach kiedy szybkow-iążące kleje są
polecane
1 biała paczka (25 kg) 7,1 - 8,8 litra wody
46 4746 47
KERLITE Cotto d’Este > KERLITE Technical Manual
Supporting material: concrete
A.4b - Wall installation in exteriors of KERLITE 3plus and KERLITE 5plus
At the discretion
of I.S.
Manufac-turer
Size of slabs(cm)
Product(*)
Primer, if necessary(*) Mixing ratio (**) Class
(*)
Nominal cover-age (*)
Workability (***)
Ready for use(***)
Installation(*)
For situations in which a
normal setting adhesives is
recommended
MAPEI
50x50; 100x40; 100x50
KERABOND + ISOLASTIC
Not necessary, according to manufacturer
1 bag (25 kg) + 8,5 kg of ISOLASTIC C2 E S2 5 m2
8 hours 14 days
Installation with a double layer of adhesive
ULTRALITE S21 bag (15 kg) + 5,9/6,2 litres of
waterC2 E S2 3 m2
100x100; 300x100 KERALASTIC T 1 can (10 kg) R2T 2,5 m2 12 hours 7 days
KERAKOLL
50x50; 100x40; 100x50
H40 NO LIMITS Not necessary, according to manufacturer
Grey 1 bag (25 kg) from 7,1 to
8,8 litres of waterC2 TE S1
6 m2 20 hours 3 days
White 1 bag (25 kg) from 7,2 to
9,5 litres of water
100x100
1 bag (25 kg) water and TOP LATEX ECO as indicated by
manufacturer
C2 TE S2
LATICRETE All sizes LATICRETE 254 Platinum
Not necessary, according to manufacturer
1 bag (25 kg) + 6 litres of water C2 TE S1 5 m2 1 day 7 days
LITOKOL All sizes CEMENTKOL K21 + LATEXKOL
Not necessary, according to manufacturer
1 bag (25 kg) + 7,5 kg of LATEXKOL C2 S2 5 m2 8 hours 7 days
PCI - BASF All sizes PCI NANOLIGHT + PCI LASTOFLEX
Not necessary, according to manufacturer
1 bag (15 kg) + 1 can of PCI
LASTOFLEX (4 kg) + 6 litres of water
C2 TE S2 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBERAll sizes WEBER.COL PRO
HP + WEBER L50Not necessary, according to
manufacturer
1 bag (15 kg) + 7 litres of WEBER
L50C2 TE S2 5 m2 8 hours 14 days
ARDEX All sizesARDEX X 77
microtec + ARDEX E 90
Not necessary, according to manufacturer
1 bag (25 kg) + 1 can of ARDEX E 90 (4,5 kg) + 9 litres of
water
C2 T(T)E(E) S2 10 m2 8 hours 1 day
For situations in which a
quick setting adhesive is
recommended
MAPEI
50x50; 100x40; 100x50
ULTRALITE S2 QUICK Not necessary, according to
manufacturer
1 bag (15 kg) + 6 litres of water C2 FE S2 4 m2
3 hours2 days
Installation with a double layer of adhesive
100x100; 300x100
KERAQUICK + LATEX PLUS
1 bag (25 kg) + 8,5 kg of LATEX PLUS C2 FT S2 5 m2 1 day
KERAKOLL
50x50; 100x40; 100x50;
H40 ECO RAPIDFLEX
Not necessary, according to manufacturer
1 bag (25 kg) + 6,3 litres of water
C2F TE S1
6 m2 3 hours 2 days100x100
1 bag (25 kg) water and TOP LATEX ECO as indicated by
manufacturer
C2F TE S2
LATICRETE All sizes
LATICRETE 335 Rapid Super Flex + LATICRETE 282
Latex Additive
Not necessary, according to manufacturer
1 bag (25 kg) + 6/7 litres of latex C2 TE F 5 m2 6 hours 2 days
LITOKOL All sizes LITOSTONE K99 + LATEXKOL
Not necessary, according to manufacturer
1 bag (25 kg) + 7,5 kg of LATEXKOL C2 FE S2 5 m2 4 hours 1 day
PCI - BASF All sizes PCI NANOLIGHT + PCI LASTOFLEX
Not necessary, according to manufacturer
1 bag (15 kg) + 1 can of PCI
LASTOFLEX (4 kg) + 6 litres of water
C2 TE S2 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBERAll sizes WEBER.COL.FIX CR Not necessary, according to
manufacturer 1 bucket (10 kg) R2 T 3 m2 12 hours 2 daysInstallation with a single layer of adhesive (6 mm
trowel)
ARDEX All sizesARDEX X 77 S
microtec + ARDEX E 90
Not necessary, according to manufacturer
1 bag (25 kg) + 3 kg of ARDEX E 90 +
7,5 litres of water
C2 FT(T)E S2 10 m2 90 min. 6 hours Installation with a
double layer of adhesive
(*) Instructions provided directly by manufacturers, who guarantee the information given. For explanations or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
(**) Instructions provided directly by manufacturers, who guarantee the information given. If a product is offered in both "white" and a "grey" versions, the mixing ratio may vary. For explana-tions or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
(***) Ratings provided directly by manufacturers, that guarantee the information given, based on laboratory tests performed at 23° C and with a relative humidity of 50%. For use in different situations, contact the technical support office of the respective manufacturers. For explanations or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
Supporting material: plaster
A.4a - Wall installation in exteriors of KERLITE 3plus and KERLITE 5plus
At the discretion
of I.S.
Manufac-turer
Size of slabs(cm)
Product(*)
Primer, if necessary(*) Mixing ratio (**) Class
(*)
Nominal cover-age (*)
Workability (***)
Ready for use(***)
Installation(*)
For situations in which a
normal setting adhesives is
recommended
MAPEI
50x50; 100x40; 100x50
KERABOND + ISOLASTIC
Not necessary, according to manufacturer
1 bag (25 kg) + 8,5 kg of ISOLASTIC C2 E S2 5 m2
8 hours 14 days
Installation with a double layer of adhesive
ULTRALITE S21 bag (15 kg) + 5,9/6,2 litres of
waterC2 E S2 3 m2
100x100; 300x100 KERALASTIC T 1 can (10 kg) R2T 2,5 m2 12 hours 7 days
KERAKOLL
50x50; 100x40; 100x50
H40 NO LIMITS Not necessary, according to manufacturer
Grey 1 bag (25 kg) from 7,1 to
8,8 litres of waterC2 TE S1
6 m2 20 hours 3 days
White 1 bag (25 kg) from 7,2 to
9,5 litres of water
100x100
1 bag (25 kg) water and TOP LATEX ECO as indicated by
manufacturer
C2 TE S2
LATICRETE All sizes LATICRETE 254 Platinum
Not necessary, according to manufacturer
1 bag (25 kg) + 6 litres of water C2 TE S1 5 m2 1 day 7 days
LITOKOL All sizes CEMENTKOL K21 + LATEXKOL
Not necessary, according to manufacturer
1 bag (25 kg) + 7,5 kg of LATEXKOL C2 S2 5 m2 8 hours 7 days
PCI - BASF All sizes PCI NANOLIGHT + PCI LASTOFLEX
Not necessary, according to manufacturer
1 bag (15 kg) + 1 can of PCI
LASTOFLEX (4 kg) + 5 litres of water
C2 TE S2 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBERAll sizes WEBER.COL PRO
HP + WEBER L50Not necessary, according to
manufacturer
1 bag (15 kg) + 7 litres of WEBER
L50C2 TE S2 5 m2 8 hours 14 days
ARDEX All sizesARDEX X 77
microtec + ARDEX E 90
Not necessary, according to manufacturer
1 bag (25 kg) + 1 can of ARDEX E 90 (4,5 kg) + 9 litres of
water
C2 T(T)E(E) S2 10 m2 8 hours 1 day
For situations in which a
quick setting adhesive is
recommended
MAPEI
50x50; 100x40; 100x50
ULTRALITE S2 QUICK
Not necessary, according to manufacturer
1 bag (15 kg) + 6 litres of water C2 FE S2 4 m2
3 hours
2 days
Installation with a double layer of adhesive
100x100; 300x100
KERAQUICK + LATEX PLUS
1 bag (25 kg) + 8,5 kg of LATEX PLUS C2 FT S2 5 m2 1 day
KERAKOLL
50x50; 100x40; 100x50;
H40 ECO RAPIDFLEX
Not necessary, according to manufacturer
1 bag (25 kg) + 6,3 litres of water
C2F TE S1
6 m2 3 hours 2 days
100x100
1 bag (25 kg) water and TOP LATEX ECO as indicated by
manufacturer
C2F TE S2
LATICRETE All sizes
LATICRETE 335 Rapid Super Flex + LATICRETE 282
Latex Additive
Not necessary, according to manufacturer
1 bag (25 kg) + 6/7 litres of latex C2 TE F 5 m2 6 hours 2 days
LITOKOL All sizes LITOSTONE K99 + LATEXKOL
Not necessary, according to manufacturer
1 bag (25 kg) + 7,5 kg of LATEXKOL C2 FE S2 5 m2 4 hours 1 day
PCI - BASF All sizes PCI NANOLIGHT + PCI LASTOFLEX
Not necessary, according to manufacturer
1 bag (15 kg) + 1 can of PCI
LASTOFLEX (4 kg) + 5 litres of water
C2 TE S2 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBER
50x50; 100x40; 100x50; 100x100
WEBER.COL PRO MARMO + WEBER
L50 Not necessary, according to manufacturer
1 bag (25 kg)+ 7 litres of WEBER L50
C2 FT S1 5 m2 4 hours 3 days
WEBER.COL PRO RAPID + WEBER
L50
1 bag (25 kg)+ 6-6,5 litres of
WEBER L50
ARDEX All sizesARDEX X 77 S
microtec + ARDEX E 90
Not necessary, according to manufacturer
1 bag (25 kg) + 3 kg of ARDEX E 90 +
7,5 litres of water
C2 FT(T)E S2 10 m2 90 min. 6 hours
(*) Instructions provided directly by manufacturers, who guarantee the information given. For explanations or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
(**) Instructions provided directly by manufacturers, who guarantee the information given. If a product is offered in both "white" and a "grey" versions, the mixing ratio may vary. For explana-tions or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
(***) Ratings provided directly by manufacturers, that guarantee the information given, based on laboratory tests performed at 23° C and with a relative humidity of 50%. For use in different situations, contact the technical support office of the respective manufacturers. For explanations or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
Odpowiedzial-ność instalatora
w sytuacjach kiedy normalne
kleje są polecane
Producent Produkt(*)Rozmiar płyt (cm) Podkład, jeśli konieczny
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Proporcje mieszania (**)
Klasa (*)
nominalne pokrycie
(*)
możliwość obróbki
(***)
gotowe do użycia (***)
montaż (*)
Instrukcje podane bezpośrednio przez producentów, którzy gwarantują poprawność informacji. Po więcej szczegółów, skontaktuj się ze wsparciem technicznym odpowiednich producentów (zobacz “9 - Przydatne kontakty”) “.
Instrukcje podane bezpośrednio przez producentów, którzy gwarantują poprawność informacji. Jeśli produkt jest oferowany zarówno w wersjach “biały” i “szary” , proporcje mieszania mogą się różnić. Po więcej szczegółów, skontaktuj się ze wsparciem technicznym odpowiednich producentów (zobacz “9 - Przydatne kontakty”) “.
Instrukcje podane bezpośrednio przez producentów, którzy gwarantują poprawność informacji. Na podstawie badań laboratoryjnych przeprowadzonych w temperaturze 23 ° C i przy wilgotności względnej 50%. W przypadku zastosowania w innych sytuacjach lub w celu uzyskania więcej szczegółów, skontaktuj się ze wsparciem technicznym odpowiednich producentów (zobacz “9 - Przydatne kontakty”) “.
materiał podłoża: beton
a.4a - KERLITE 3plus i KERLITE 5plus - montaż na ścianie na zewnątrz
1 paczka (25 kg) + 6 litrów wody
1 paczka (25 kg) + 6,3 litrów wody
1 paczka (15 kg) + 6 litrów wody
1 paczka (25 kg) + 8,5 kg LATEX PLUS
1 paczka (25 kg) + 6/7 litrów latexu
1 paczka (25 kg) + 7,5 kg LATEXKOL
1 paczka (25 kg) + 7,5 kg LATEXKOL
1 paczka (15 kg) + 7 litrów WEBER L50
1 wiadro (10 kg)
1 paczka 25 kg) + 1 puszka ARDEX E 90 (4,5 kg) + 9 litrów
wody
1 paczka 25 kg) + 3kg ARDEX E 90 + 7,5
litrów wody
1 paczka (15 kg) + 1 puszka PCI LASTOF-LEX (4 kg) + 5 litrów
wody
1 paczka (15 kg) + 1 puszka PCI LASTOF-LEX (4 kg) + 5 litrów
wody
1 biała paczka (25 kg) 7,2 - 9,5 litra wody
1 paczka (25 kg) wody i TOP LATEX ECO wg. zaleceń
producenta
1 paczka (25 kg) wody i TOP LATEX ECO wg. zaleceń
producenta
1 paczka (15 kg) + 5,9/6,2 litra wody
1 paczka (25 kg) + 8,5 kg ISOLASTIC
12 godzin
8 godzin
20 godzin
1 dzień
1 dzień
1 dzień
1 dzień
1 dzień
1 dzień
2 dni
2 dni
2 dni
2 dni
6 godzin
3 godziny
3 godziny
90 min
8 godzin
12 godzin
4 godziny
6 godzin
3 dni
Montaż z podwójną warstwą kleju
Montaż z podwójną warstwą kleju
Montaż z podwójną warstwą kleju
14 dni
7 dni
7 dni
7 dni
14 dni
8 godzin
8 godzin
8 godzin
8 godzin
1 puszka (10 kg)
Wszystkie rozmiaryWszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
w sytuacjach kiedy szybkow-iążące kleje są
polecane
1 biała paczka (25 kg) 7,1 - 8,8 litra wody
Montaż z pojedyńczą warstwą kleju (kielnia 6 mm)
48 4948 49
KERLITE Cotto d’Este > KERLITE Technical Manual
( ) Upon condition that surfaces are sheltered (e.g. loggias, covered balconies, etc.) and made totally impervious. The use of sizes that are not larger than 50x50 cm is recommended.
(*) Instructions provided directly by manufacturers, who guarantee the information given. For explanations or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
At the discretion
of I.S.
Manufac-turer
Size of slabs(cm)
Product(*)
Primer, if necessary(*) Mixing ratio (**) Class
(*)
Nominal cover-age (*)
Setting for foot traffic and workability
(***)
Ready for use(***)
Installation(*)
For situations in which a
normal setting adhesives is
recommended
MAPEI All sizesKERALASTIC
Not necessary, according to manufacturer 1 can (10 kg)
R22,5 m2 12 hours 7 days
Installation with a double layer of adhesive
KERALASTIC T R2T
KERAKOLL
All sizes in interiors H40 NO LIMITS
Grey 1 bag (25 kg) from 7,1 to 8,8 litres of water
C2 TE S1 C2 TE S1 6 m2 24 hours 3 daysWhite 1 bag (25 kg) from 7,2 to 9,5 litres of water
All sizes SUPERFLEX ECO Not necessary, according to manufacturer 1 bucket (8 kg) R2T 3 m2 1 day 3 days
LATICRETE All sizes LATALASTIK Not necessary, according to manufacturer
1 bucket of component A (5 kg) 1 bucket
of component B (2 kg)
R2T 3 m2 1 day 5 days
LITOKOL All sizes LITOELASTIC Not necessary, according to manufacturer 1 bucket (10 kg) R2T 3 m2 12 hours 5 days
PCI - BASF All sizes PCI COLLASTIC Not necessary, according to manufacturer 3 kg bucket (A+B) R2T 1,5 m2 12 hours 1 day
Installation with a single layer of adhesive (trowel with 10 mm tilted teeth)
SAINT-GOBAIN /
WEBERAll sizes WEBER.COL.FIX CR Not necessary, according to
manufacturer 1 bucket (10 kg) R2 T 3 m2 12 hours 2 days
ARDEX All sizesARDEX X 78
microtec + ARDEX E 90
ARDEX P 82
1 bag (25 kg) + 1 can of ARDEX E 90 (4,5 kg) + 9 litres of
water
C2 E(E) S2 6 m2 8 hours 1 day
Installation with a single layer of adhesive
(trowel with 10 mm tilted teeth or ARDEX Microtec
trowel)
For situations in which a
quick setting adhesive is
recommended
MAPEI All sizes KERAQUICK + LATEX PLUS
Not necessary, according to manufacturer
1 bag (25 kg) + 8,5 kg of LATEX PLUS C2 FT S2 2,5 m2 3 hours 1 day
Installation with a double layer of adhesive
KERAKOLL All sizes
H40 ECO RAPIDFLEX
PRIMER A ECO or KERAGRIP ECO depending on support
1 bag (25 kg) + 6,3 litres of water
C2F TE S1 6 m2 3 hours 2 days
SUPERFLEX ECO Not necessary, according to manufacturer 1 bucket (8 kg) R2T 3 m2 1 day 3 days
LATICRETE All sizes LATALASTIK Not necessary, according to manufacturer
1 bucket of component A (5 kg) 1 bucket
of component B (2 kg)
R2T 3 m2 1 day 5 days
LITOKOL All sizes LITOELASTIC Not necessary, according to manufacturer 1 bucket (10 kg) R2T 3 m2 12 hours 7 days
PCI - BASF All sizes PCI COLLASTIC Not necessary, according to manufacturer 3 kg bucket (A+B) R2T 1.5 m2 3 hours 12 hours
Installation with a single layer of adhesive (trowel with 10 mm tilted teeth)
SAINT-GOBAIN /
WEBERAll sizes WEBER.COL.FIX CR Not necessary, according to
manufacturer 1 bucket (10 kg) R2 T 3 m2 12 hours 2 days
ARDEX All sizesARDEX X 78 S
microtec + ARDEX E 90
ARDEX P 821 bag (25 kg) + 3
kg of ARDEX E 90 + 7 litres of water
C2 FE S2 6 m2 90 min. 6 hours
Installation with a single layer of adhesive
(trowel with 10 mm tilted teeth or ARDEX Microtec
trowel)
Supporting material: wood, PVC, rubber, linoleum, metal, resin
A.5b - Floor installation in interiors/exteriors of KERLITE 3plus and KERLITE 5plus
(**) Instructions provided directly by manufacturers, who guarantee the information given. If a product is offered in both "white" and a "grey" versions, the mixing ratio may vary. For explana-tions or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
(***) Ratings provided directly by manufacturers, that guarantee the information given, based on laboratory tests performed at 23° C and with a relative humidity of 50%. For use in different situations, contact the technical support office of the respective manufacturers. For explanations or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
At the discretion
of I.S.
Manufac-turer
Size of slabs(cm)
Product(*)
Primer, if necessary(*) Mixing ratio (**) Class
(*)
Nominal cover-age (*)
Setting for foot traffic and work-
ability (***)
Ready for use(***)
Installation(*)
For situations in which a
normal setting adhesives is
recommended
MAPEI
50x50;100x40; 100x50
KERAFLEX MAXI S1
COMPULSORY for gypsum-based, anhydride or absorbent surfaces:
Primer G or ECOPRIM T
For non-absorbent supports: ECOPRIM GRIP
1 bag (25 kg) + 7,2/7,7 litres of
waterC2 TE S1
3,5 m2
1 day
14 days
Installation with a double layer of adhesive
ULTRALITE S11 bag (15 kg) + 8,4/8,7 litres of
waterC2 TE S1 8 hours
100x100; 300x100
ULTRALITE S21 bag (15 kg) + 5,9/6,2 litres of
waterC2 E S2
1 day
KERABOND + ISOLASTIC
1 bag (25 kg) + 8,5 kg of ISOLASTIC C2 E S2
5 m2
For heated screeds:All sizes
KERABOND + ISOLASTIC
1 bag (25 kg) + 8,5 kg of ISOLASTIC C2 E S2
ULTRALITE S21 bag (15 kg) + 5,9/6,2 litres of
waterC2 E S2 3,5 m2
KERAKOLL All sizes H40 NO LIMITSFor gypsum-based
surfaces:Primer A Eco
Grey 1 bag (25 kg) from 7,1 to
8,8 litres of waterC2 TE S1 6 m2 1 day 3 days
White 1 bag (25 kg) from 7,2 to
9,5 litres of water
LATICRETE All sizes LATICRETE 254 Platinum
Not necessary, according to manufacturer
1 bag (25 kg) + 6 litres of water C2 TE S1 5 m2 1 day 7 days
LITOKOL
50x50;100x40; 100x50 SUPERFLEX K77
For anhydrite screeds: Primer C
1 bag (25 kg) + 8,5 litres of water C2 TE S1
5 m2 8 hours 7 days100x100; 300x100
CEMENTKOL K21 + LATEXKOL
1 bag (25 kg) + 7,5 kg of LATEXKOL
C2 S2
For heated screeds:All sizes
1 bag (25 kg) + 7,5 kg of LATEXKOL
C2 S2
PCI - BASF All sizes PCI NANOLIGHT + PCI LASTOFLEX
If support is anhydrite-based: PCI GISOGRUNDOn old, non-absorbent
floors: PCI GISOGRUND 303
1 bag (15 kg) + 1 can of PCI LASTOFLEX (4 kg) + 5 litres of
water
C2 TE S2 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBER
All sizes WEBER.COL PRO HP + WEBER L50 For anhydrite- or calcium
sulphate-based surfaces: WEBER.PRIM PF15
1 bag (15 kg) + 7 litres of WEBER
L50C2 TE S2
5 m2
8 hours
14 daysFor interiors only:
50x50;100x40; 100x50; 100x100
WEBER.COL PRO HF LIGHT
1 bag (15 kg) + 8 litres of water C2 TE S2 1 day
ARDEX All sizesARDEX X 78 microtec + ARDEX E 90
For gypsum- and anhydrite-based,
absorbent or polished surfaces: ARDEX P 51
1 bag (25 kg) + 1 can of ARDEX E 90 (4,5 kg) + 9
litres of water
C2 E(E) S2 6 m2 8 hours 1 day
Installation with a single layer of adhesive (trowel with 10 mm tilted teeth
or ARDEX Microtec trowel)
For situations in which a
quick setting adhesive is
recommended
MAPEI
50x50;100x40; 100x50
GRANIRAPID
COMPULSORY for gypsum-based, anhydride or absorbent surfaces:
Primer G or ECOPRIM T
For non-absorbent supports: ECOPRIM GRIP
Component A: 1 bag (25 kg)
Component B: tub (5,5 kg)
C2 F S1 4 m2
3 hours 1 day
Installation with a double layer of adhesive
ULTRALITE S1 QUICK
1 bag (15 kg) + 5,1/5,7 litres of
water
C2 FTE S1 3,5 m2
100x100; 300x100
ULTRALITE S2 QUICK
1 bag (15 kg) + 5,1/5,7 litres of
waterC2 FE S2
4 m2ELASTORAPID
Component A: 1 bag (25 kg)
Component B: tub (6,5 kg)
C2 FTE S2
For heated screeds:
50x50;100x40; 100x50
ELASTORAPID
Component A: 1 bag (25 kg)
Component B: tub (6,5 kg)
C2 FTE S2
For heated screeds: 100x100; 300x100
KERAQUICK + LATEX PLUS
1 bag (25 kg) + 8,5 kg of LATEX
PLUS"
C2 FT S2 5 m2
KERAKOLL All sizes H40 ECO RAPIDFLEX
For gypsum-based or anhydride surfaces:
Primer A Eco
1 bag (25 kg) + 6,3 litres of water
C2F TE S1 6 m2 3 hours 2 days
LATICRETE All sizes
LATICRETE 335 Rapid Super Flex + LATICRETE 282
Latex Additive
Not necessary, according to manufacturer
1 bag (25 kg) + 6/7 litres of latex C2 TE F 5 m2 6 hours 2 days
LITOKOL
50x50; 100x40; 100x50
LITOSTONE K99 + LATEXKOL +
water
For gypsum-based surfaces: Primer C
1 bag (25 kg) + 3,5 litres of
LATEXKOL + 3,5 litres of water
C2 FE S1
5 m2 4 hours 1 day100x100; 300x100
LITOSTONE K99 + LATEXKOL
1 bag (25 kg) + 7,5 kg of LATEXKOL
C2 FE S2
For heated screeds: all sizes
1 bag (25 kg) + 7,5 kg of LATEXKO
C2 FE S2
PCI - BASF All sizes PCI NANOLIGHT + PCI LASTOFLEX
If support is anhydrite-based:
PCI GISOGRUNDOn old, non-absorbent
floors:PCI GISOGRUND 303
1 bag (15 kg) + 1 can of PCI LASTOFLEX (4 kg) + 5 litres of
water
C2 TE S2 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBERAll sizes
WEBER.COL PRO MARMO + WEBER
L50 For anhydrite- or calcium sulphate-based surfaces:
WEBER.PRIM PF15
1 bag (25 kg)+ 7 litres of WEBER L50
C2 FT S1 5 m2 4 hours 3 days
WEBER.COL PRO RAPID + WEBER
L50
1 bag (25 kg)+ 6-6,5 litres of
WEBER L50
ARDEX All sizesARDEX X 78 S microtec + ARDEX E 90
For gypsum- and anhydrite-based,
absorbent or polished surfaces: ARDEX P 51
1 bag (25 kg) + 3 kg of ARDEX
E 90 + 7 litres of water
C2 FE S2 6 m2 90 min. 6 hours
Installation with a single layer of adhesive (trowel with 10 mm tilted teeth
or ARDEX Microtec trowel)
Supporting material: cement-based screeds, calcium sulphate-based or heated screeds, self-levelling products, concrete, old ceramic tile, marble slabs, stone
A.5a - Floor installation in interiors/exteriors of KERLITE 3plus and KERLITE 5plus
Odpowiedzial-ność instalatora
w sytuacjach kiedy normalne
kleje są polecane
Producent Produkt(*)Rozmiar płyt (cm) Podkład, jeśli konieczny
Niezbędne przy gipsowych, anhydrytowych lub
chłonnych powierzchniach:
Primer G lub ECOPRIM Tdla niechłonnych: ECOPRIM
GRIP
Niezbędne przy gipsowych, anhydrytowych lub
chłonnych powierzchniach:
Primer G lub ECOPRIM Tdla niechłonnych: ECOPRIM
GRIP
Dla gipsowych powier-zchni: Primer A Eco
Dla gipsowych powier-zchni: Primer A Eco
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Dla anhydrytowych powier-zchni: Primer C
Dla anhydrytowych powier-zchni: Primer C
Dla anhydrytowych lub wapienno-siarczanowych powierzchni: WEBER.PRIM
PF15
Dla anhydrytowych lub wapienno-siarczanowych powierzchni: WEBER.PRIM
PF15
Dla gipsowychi anhydrytowych, absorbujących lub polerow-
anych powierzchni: ARDEX P 51
Dla gipsowychi anhydrytowych, absorbujących lub polerow-
anych powierzchni: ARDEX P 51
Jeżeli podłoże jest anhydrytowe: PCI GISOGRUND
Na starej, nieabsorbującej powi-erzchni PCI GISOGRUND 303
Jeżeli podłoże jest anhydrytowe: PCI GISOGRUND
Na starej, nieabsorbującej powi-erzchni PCI GISOGRUND 303
Proporcje mieszania (**)
Klasa nominalne
pokrycie (*)
możliwość obróbki
gotowe do użycia
montaż (*)
a.5a - KERLITE 3plus i KERLITE 5plus - montaż na podłodze wewnątrz/na zewnątrz*
materiał podłoża: wylewki cementowe, siarczanowo wapniowe lub podgrzewane, produkty samopoziomujące, beton, stare płytki ceramiczne, płyty marmurowe, kamień naturalny
1 paczka (25 kg) + 3,5 litra LATEXKOL + 3,5
litra wody
1 paczka (15 kg) + 5,1/5,7 litra wody
1 paczka (25 kg) + 6/7 litrów latexu
1 paczka (25 kg) + 6,3 litra wody
1 paczka (15 kg) + 5,1/5,7 litra wody
1 paczka (15 kg) + 8 litrów wody
1 paczka (25 kg) + 8,5 litra wody
1 paczka (25 kg) + 6 litrów wody
1 biała paczka (25 kg) 7,2 - 9,5 litra wody
1 szara paczka (25 kg) 7,1 - 8,8 litra wody
1 paczka (15 kg) + 5,9/6,2 litra wody
1 paczka (15 kg) + 8,4/8,7 litra wody
1 paczka (25 kg) + 7,2/7,7 litra wody
1 paczka (15 kg) + 5,9/6,2 litra wody
1 dzień
1 dzień
1 dzień
1 dzień
1 dzień
1 dzień
1 dzień
2 dni
2 dni
1 dzień
1 dzień
3 dni
6 godzin
4 godziny
3 godziny
3 godziny
6 godzin
90 min
4 godziny
8 godzin
3 dni
7 dni
7 dni
Montaż z podwójną warstwą kleju
Montaż z podwójną warstwą kleju
Montaż z pojedyńczą warstwą kleju (kielnia pochylone ząbki
10 mm) lub kielnia ARDEX Microtec
Montaż z pojedyńczą warstwą kleju (kielnia pochylone ząbki
10 mm) lub kielnia ARDEX Microtec
14 dni
14 dni1 dzień
8 godzin
8 godzin
8 godzin
8 godzin
8 godzin
1 paczka (25 kg) + 8,5 kg ISOLASTIC
1 paczka (25 kg) + 8,5 kg ISOLASTIC
Komponent A: 1 paczka (25 kg)
Komponent B: opakowanie (6,5 kg)
Komponent A: 1 paczka (25 kg)
Komponent B: opakowanie (6,5 kg)
1 paczka (25 kg) + 8,5 kg LATEX PLUS
Komponent A: 1 paczka (25 kg)
Komponent B: opakowanie (5,5 kg)
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Podgrzewane posadzki: Wszystkie rozmiary
Podgrzewane posadzki: Wszystkie rozmiary
Tylko dla wnętrz:
Podgrzewaneposadzki:
Podgrzewaneposadzki:
w sytuacjach kiedy szybkow-iążące kleje są
polecane
1 paczka (25 kg) + 7,5 kg LATEXKOL1 paczka (25 kg) + 7,5 kg LATEXKOL
1 paczka (25 kg) + 7,5 kg LATEXKOL
1 paczka (25 kg) + 7,5 kg LATEXKOL
1 paczka (15 kg) + 7 litrów WEBER L50
1 paczka (25 kg) + 6/6,5 litrów WEBER L50
1 paczka (25 kg) + 7 litrów WEBER L50
1 paczka 25 kg) + 1 puszka ARDEX E 90 (4,5 kg) + 9 litrów
wody
1 paczka (15 kg) + 1 puszka PCI LASTOF-LEX (4 kg) + 5 litrów
wody
1 paczka (15 kg) + 1 puszka PCI LASTOF-LEX (4 kg) + 5 litrów
wody
1 paczka 25 kg) + 3kg ARDEX E 90 + 7,5
litrów wody
48 4948 49
KERLITE Cotto d’Este > KERLITE Technical Manual
( ) Upon condition that surfaces are sheltered (e.g. loggias, covered balconies, etc.) and made totally impervious. The use of sizes that are not larger than 50x50 cm is recommended.
(*) Instructions provided directly by manufacturers, who guarantee the information given. For explanations or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
At the discretion
of I.S.
Manufac-turer
Size of slabs(cm)
Product(*)
Primer, if necessary(*) Mixing ratio (**) Class
(*)
Nominal cover-age (*)
Setting for foot traffic and workability
(***)
Ready for use(***)
Installation(*)
For situations in which a
normal setting adhesives is
recommended
MAPEI All sizesKERALASTIC
Not necessary, according to manufacturer 1 can (10 kg)
R22,5 m2 12 hours 7 days
Installation with a double layer of adhesive
KERALASTIC T R2T
KERAKOLL
All sizes in interiors H40 NO LIMITS
Grey 1 bag (25 kg) from 7,1 to 8,8 litres of water
C2 TE S1 C2 TE S1 6 m2 24 hours 3 daysWhite 1 bag (25 kg) from 7,2 to 9,5 litres of water
All sizes SUPERFLEX ECO Not necessary, according to manufacturer 1 bucket (8 kg) R2T 3 m2 1 day 3 days
LATICRETE All sizes LATALASTIK Not necessary, according to manufacturer
1 bucket of component A (5 kg) 1 bucket
of component B (2 kg)
R2T 3 m2 1 day 5 days
LITOKOL All sizes LITOELASTIC Not necessary, according to manufacturer 1 bucket (10 kg) R2T 3 m2 12 hours 5 days
PCI - BASF All sizes PCI COLLASTIC Not necessary, according to manufacturer 3 kg bucket (A+B) R2T 1,5 m2 12 hours 1 day
Installation with a single layer of adhesive (trowel with 10 mm tilted teeth)
SAINT-GOBAIN /
WEBERAll sizes WEBER.COL.FIX CR Not necessary, according to
manufacturer 1 bucket (10 kg) R2 T 3 m2 12 hours 2 days
ARDEX All sizesARDEX X 78
microtec + ARDEX E 90
ARDEX P 82
1 bag (25 kg) + 1 can of ARDEX E 90 (4,5 kg) + 9 litres of
water
C2 E(E) S2 6 m2 8 hours 1 day
Installation with a single layer of adhesive
(trowel with 10 mm tilted teeth or ARDEX Microtec
trowel)
For situations in which a
quick setting adhesive is
recommended
MAPEI All sizes KERAQUICK + LATEX PLUS
Not necessary, according to manufacturer
1 bag (25 kg) + 8,5 kg of LATEX PLUS C2 FT S2 2,5 m2 3 hours 1 day
Installation with a double layer of adhesive
KERAKOLL All sizes
H40 ECO RAPIDFLEX
PRIMER A ECO or KERAGRIP ECO depending on support
1 bag (25 kg) + 6,3 litres of water
C2F TE S1 6 m2 3 hours 2 days
SUPERFLEX ECO Not necessary, according to manufacturer 1 bucket (8 kg) R2T 3 m2 1 day 3 days
LATICRETE All sizes LATALASTIK Not necessary, according to manufacturer
1 bucket of component A (5 kg) 1 bucket
of component B (2 kg)
R2T 3 m2 1 day 5 days
LITOKOL All sizes LITOELASTIC Not necessary, according to manufacturer 1 bucket (10 kg) R2T 3 m2 12 hours 7 days
PCI - BASF All sizes PCI COLLASTIC Not necessary, according to manufacturer 3 kg bucket (A+B) R2T 1.5 m2 3 hours 12 hours
Installation with a single layer of adhesive (trowel with 10 mm tilted teeth)
SAINT-GOBAIN /
WEBERAll sizes WEBER.COL.FIX CR Not necessary, according to
manufacturer 1 bucket (10 kg) R2 T 3 m2 12 hours 2 days
ARDEX All sizesARDEX X 78 S
microtec + ARDEX E 90
ARDEX P 821 bag (25 kg) + 3
kg of ARDEX E 90 + 7 litres of water
C2 FE S2 6 m2 90 min. 6 hours
Installation with a single layer of adhesive
(trowel with 10 mm tilted teeth or ARDEX Microtec
trowel)
Supporting material: wood, PVC, rubber, linoleum, metal, resin
A.5b - Floor installation in interiors/exteriors of KERLITE 3plus and KERLITE 5plus
(**) Instructions provided directly by manufacturers, who guarantee the information given. If a product is offered in both "white" and a "grey" versions, the mixing ratio may vary. For explana-tions or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
(***) Ratings provided directly by manufacturers, that guarantee the information given, based on laboratory tests performed at 23° C and with a relative humidity of 50%. For use in different situations, contact the technical support office of the respective manufacturers. For explanations or more details, you can contact the technical support offices of the respective manufacturers (see “9 - Useful contacts”).
At the discretion
of I.S.
Manufac-turer
Size of slabs(cm)
Product(*)
Primer, if necessary(*) Mixing ratio (**) Class
(*)
Nominal cover-age (*)
Setting for foot traffic and work-
ability (***)
Ready for use(***)
Installation(*)
For situations in which a
normal setting adhesives is
recommended
MAPEI
50x50;100x40; 100x50
KERAFLEX MAXI S1
COMPULSORY for gypsum-based, anhydride or absorbent surfaces:
Primer G or ECOPRIM T
For non-absorbent supports: ECOPRIM GRIP
1 bag (25 kg) + 7,2/7,7 litres of
waterC2 TE S1
3,5 m2
1 day
14 days
Installation with a double layer of adhesive
ULTRALITE S11 bag (15 kg) + 8,4/8,7 litres of
waterC2 TE S1 8 hours
100x100; 300x100
ULTRALITE S21 bag (15 kg) + 5,9/6,2 litres of
waterC2 E S2
1 day
KERABOND + ISOLASTIC
1 bag (25 kg) + 8,5 kg of ISOLASTIC C2 E S2
5 m2
For heated screeds:All sizes
KERABOND + ISOLASTIC
1 bag (25 kg) + 8,5 kg of ISOLASTIC C2 E S2
ULTRALITE S21 bag (15 kg) + 5,9/6,2 litres of
waterC2 E S2 3,5 m2
KERAKOLL All sizes H40 NO LIMITSFor gypsum-based
surfaces:Primer A Eco
Grey 1 bag (25 kg) from 7,1 to
8,8 litres of waterC2 TE S1 6 m2 1 day 3 days
White 1 bag (25 kg) from 7,2 to
9,5 litres of water
LATICRETE All sizes LATICRETE 254 Platinum
Not necessary, according to manufacturer
1 bag (25 kg) + 6 litres of water C2 TE S1 5 m2 1 day 7 days
LITOKOL
50x50;100x40; 100x50 SUPERFLEX K77
For anhydrite screeds: Primer C
1 bag (25 kg) + 8,5 litres of water C2 TE S1
5 m2 8 hours 7 days100x100; 300x100
CEMENTKOL K21 + LATEXKOL
1 bag (25 kg) + 7,5 kg of LATEXKOL
C2 S2
For heated screeds:All sizes
1 bag (25 kg) + 7,5 kg of LATEXKOL
C2 S2
PCI - BASF All sizes PCI NANOLIGHT + PCI LASTOFLEX
If support is anhydrite-based: PCI GISOGRUNDOn old, non-absorbent
floors: PCI GISOGRUND 303
1 bag (15 kg) + 1 can of PCI LASTOFLEX (4 kg) + 5 litres of
water
C2 TE S2 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBER
All sizes WEBER.COL PRO HP + WEBER L50 For anhydrite- or calcium
sulphate-based surfaces: WEBER.PRIM PF15
1 bag (15 kg) + 7 litres of WEBER
L50C2 TE S2
5 m2
8 hours
14 daysFor interiors only:
50x50;100x40; 100x50; 100x100
WEBER.COL PRO HF LIGHT
1 bag (15 kg) + 8 litres of water C2 TE S2 1 day
ARDEX All sizesARDEX X 78 microtec + ARDEX E 90
For gypsum- and anhydrite-based,
absorbent or polished surfaces: ARDEX P 51
1 bag (25 kg) + 1 can of ARDEX E 90 (4,5 kg) + 9
litres of water
C2 E(E) S2 6 m2 8 hours 1 day
Installation with a single layer of adhesive (trowel with 10 mm tilted teeth
or ARDEX Microtec trowel)
For situations in which a
quick setting adhesive is
recommended
MAPEI
50x50;100x40; 100x50
GRANIRAPID
COMPULSORY for gypsum-based, anhydride or absorbent surfaces:
Primer G or ECOPRIM T
For non-absorbent supports: ECOPRIM GRIP
Component A: 1 bag (25 kg)
Component B: tub (5,5 kg)
C2 F S1 4 m2
3 hours 1 day
Installation with a double layer of adhesive
ULTRALITE S1 QUICK
1 bag (15 kg) + 5,1/5,7 litres of
water
C2 FTE S1 3,5 m2
100x100; 300x100
ULTRALITE S2 QUICK
1 bag (15 kg) + 5,1/5,7 litres of
waterC2 FE S2
4 m2ELASTORAPID
Component A: 1 bag (25 kg)
Component B: tub (6,5 kg)
C2 FTE S2
For heated screeds:
50x50;100x40; 100x50
ELASTORAPID
Component A: 1 bag (25 kg)
Component B: tub (6,5 kg)
C2 FTE S2
For heated screeds: 100x100; 300x100
KERAQUICK + LATEX PLUS
1 bag (25 kg) + 8,5 kg of LATEX
PLUS"
C2 FT S2 5 m2
KERAKOLL All sizes H40 ECO RAPIDFLEX
For gypsum-based or anhydride surfaces:
Primer A Eco
1 bag (25 kg) + 6,3 litres of water
C2F TE S1 6 m2 3 hours 2 days
LATICRETE All sizes
LATICRETE 335 Rapid Super Flex + LATICRETE 282
Latex Additive
Not necessary, according to manufacturer
1 bag (25 kg) + 6/7 litres of latex C2 TE F 5 m2 6 hours 2 days
LITOKOL
50x50; 100x40; 100x50
LITOSTONE K99 + LATEXKOL +
water
For gypsum-based surfaces: Primer C
1 bag (25 kg) + 3,5 litres of
LATEXKOL + 3,5 litres of water
C2 FE S1
5 m2 4 hours 1 day100x100; 300x100
LITOSTONE K99 + LATEXKOL
1 bag (25 kg) + 7,5 kg of LATEXKOL
C2 FE S2
For heated screeds: all sizes
1 bag (25 kg) + 7,5 kg of LATEXKO
C2 FE S2
PCI - BASF All sizes PCI NANOLIGHT + PCI LASTOFLEX
If support is anhydrite-based:
PCI GISOGRUNDOn old, non-absorbent
floors:PCI GISOGRUND 303
1 bag (15 kg) + 1 can of PCI LASTOFLEX (4 kg) + 5 litres of
water
C2 TE S2 5,5 m2 8 hours 1 day
SAINT-GOBAIN /
WEBERAll sizes
WEBER.COL PRO MARMO + WEBER
L50 For anhydrite- or calcium sulphate-based surfaces:
WEBER.PRIM PF15
1 bag (25 kg)+ 7 litres of WEBER L50
C2 FT S1 5 m2 4 hours 3 days
WEBER.COL PRO RAPID + WEBER
L50
1 bag (25 kg)+ 6-6,5 litres of
WEBER L50
ARDEX All sizesARDEX X 78 S microtec + ARDEX E 90
For gypsum- and anhydrite-based,
absorbent or polished surfaces: ARDEX P 51
1 bag (25 kg) + 3 kg of ARDEX
E 90 + 7 litres of water
C2 FE S2 6 m2 90 min. 6 hours
Installation with a single layer of adhesive (trowel with 10 mm tilted teeth
or ARDEX Microtec trowel)
Supporting material: cement-based screeds, calcium sulphate-based or heated screeds, self-levelling products, concrete, old ceramic tile, marble slabs, stone
A.5a - Floor installation in interiors/exteriors of KERLITE 3plus and KERLITE 5plus
Odpowiedzial-ność instalatora
w sytuacjach kiedy normalne
kleje są polecane
Producent Produkt(*)Rozmiar płyt (cm) Podkład, jeśli konieczny
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Nie konieczne, według zaleceń producenta
Proporcje mieszania (**)
Klasa (*)
nominalne pokrycie
(*)
możliwość obróbki
gotowe do użycia
montaż (*)
Instrukcje podane bezpośrednio przez producentów, którzy gwarantują poprawność informacji. Po więcej szczegółów, skontaktuj się ze wsparciem technicznym odpowiednich producentów (zobacz “9 - Przydatne kontakty”) “.
Instrukcje podane bezpośrednio przez producentów, którzy gwarantują poprawność informacji. Jeśli produkt jest oferowany zarówno w wersjach “biały” i “szary” , proporcje mieszania mogą się różnić. Po więcej szczegółów, skontaktuj się ze wsparciem technicznym odpowiednich producentów (zobacz “9 - Przydatne kontakty”) “.
Instrukcje podane bezpośrednio przez producentów, którzy gwarantują poprawność informacji. Na podstawie badań laboratoryjnych przeprowadzonych w temperaturze 23 ° C i przy wilgotności względnej 50%. W przypadku zastosowania w innych sytuacjach lub w celu uzyskania więcej szczegółów, skontaktuj się ze wsparciem technicznym odpowiednich producentów (zobacz “9 - Przydatne kontakty”) “.
Pod warunkiem, że powierzchnie są zadaszone (loggie, zadaszone balkony itp.) i są chronione przed wodą. Zaleca się użycie rozmiarów nie większych niż 50x50 cm.
materiał podłoża: drewno, PVC, guma, linoleum, metal, żywica
a.5b - KERLITE 3plus i KERLITE 5plus - montaż na podłodze wewnątrz/na zewnątrz*
1 dzień
1 dzień
2 dni
2 dni
1 dzień
1 dzień
1 dzień 1 dzień
3 dni
6 godzin
3 godziny
3 godziny
3 godziny
12 godzin
90 min
12 godzin
12 godzin
3 dni
3 dni
7 dni
7 dni
7 dni
Montaż z podwójną warstwą kleju
Montaż z podwójną warstwą kleju
Montaż z pojedyńczą warstwą kleju (kielnia pochylone ząbki
10 mm) lub kielnia ARDEX Microtec
Montaż z pojedyńczą warstwą kleju (kielnia pochylone ząbki
10 mm)
Montaż z pojedyńczą warstwą kleju (kielnia pochylone ząbki
10 mm)
Montaż z pojedyńczą warstwą kleju (kielnia pochylone ząbki
10 mm) lub kielnia ARDEX Microtec
8 godzin
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary we wnętrzach
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiaryWszystkie rozmiary
Wszystkie rozmiary
Wszystkie rozmiary
w sytuacjach kiedy szybkow-iążące kleje są
polecane
1 paczka (25 kg) + 8,5 kg LATEX PLUS
1 paczka (25 kg) + 6,3 litra wody
Komponent A: wiadro (5 kg)
Komponent B: wiadro (2 kg)
1 paczka (25 kg) + 7,5 kg LATEXKOL1 puszka (10 kg)
1 wiadro (8 kg)
1 wiadro (8 kg)
1 wiadro (10 kg)
1 wiadro (10 kg)
1 wiadro (10 kg)
wiadro 3 kg (A+B)
wiadro 3 kg (A+B)
1 paczka 25 kg) + 1 puszka ARDEX E 90 (4,5 kg) + 9 litrów
wody
1 paczka 25 kg) + 3kg ARDEX E 90 + 7,5
litrów wody