Upload
others
View
5
Download
0
Embed Size (px)
Citation preview
ELCOM srlVia follo 5 D/E - 25070 CAINO (BS) - ITALIA
Input
V out
100/250 VAc
50/60Hz
Classe di isolamento - Insulation class
CE
I out
P out
4.1A
100W @230VAc 60w@110VAc
II
IP20
Temperatura di esercizio - Working Temperature -10 °C / + 40°C
Dimmerabile - Dimmerable
207x76x35 mm
DALI / 1-10v / PUSH
24VDC
207 mm
76mm 35mm
Tel. 0039 030 6830559Fax 0039 030 6830777
Alimentatore dimmerabile DALI/1..10V/PUSH
07453
Dimmable DALI/1..10V/PUSH power supply
M M F EMC 1..10V PUSHIP20IP20
ALIMENTATORE DIMMERABILE 1..10V / PUSH - cod. 07450
SCHEDA TECNICA Data sheet
Dimmable power supply - costant voltage output 1..10V/PUSH - cod. 07450
100W 24 Vdc IP20IP20ALIMENTATORE DIMMERABILE DALI/1..10V / PUSH - cod. 07453
Dimmable DALI/1..10V/PUSH power supply - costant voltage output - cod. 07453
Marchi - Marks
Garanzia - Warranty 2 anni - years
DISEGNO - DRAWING
Misure in mm - Measures in mm
IMMAGINE INDICATIVA - INDICATIVE IMAGEDATA - DATA
Descrizione - Description
CODICE - CODE
Frequenza - Frequency
Grado IP - IP level
Dimensioni - Dimension
Syncro
Syncro
Syncro
24V DC - PWM OUTPUT
24V DC - PWM OUTPUT
24V DC - PWM OUTPUT
24V DC - PWM OUTPUT
100..250V AC
100..250V AC
100..250V AC
100..250V AC
+
+
+
+
+
+
+
+
-
-
-
-
-
-
-
-
1..10V input
Push - Button Secondary side
Push - Button primary side
Slave-Syncro
++
++
++
++
----
----
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
ON
ON
ON
ON
ON
ON
max 20 m
max 30 m
ON
ON
ON
ONON
ON ON
OFF
OFF
OFF
OFF
OFF OFF
X
X
X
X
X
1
1
1
1
3
3
3
3
2
2
2
2
4
4
4
4
Mode
Mode
Mode
Mode
Push
Push
0..10V1..10V
ON
ON
ON
ON
ONON
ON ON
OFF
OFF OFF
OFF
OFF
OFF OFF
X
X
X
X
X
1 32 4 Mode DALIPush
0..10V1..10VSlave
Slave
+ -
+ -
+ -
47K_Lin/Log
Impostazione del Dip-Switch ad apparecchio spento
Dip-switch setting only when switched off
Dip-Switch Einstellung nur bei OFF-Position
Programmation du Dip-Switch lorsque l’appareil est éteint
Ajuste de los Dip-Switches cuando el aparato está apagado
Max 15 X
DALI input
Syncro
24V DC - PWM OUTPUT
100..250V AC
+ +
- -
DALI input
++
--
1 2 3 4
ON
ONOFF OFF X
1 32 4 Mode DALI
+ -
input selector
ON
1 2 3 4
Alimentatori LED - Istruzioni di utilizzo e di installazioneFare sempre attenzione alla polarità del secondario. Installare il sistema lontano da fonti di calore e in luoghi ben aerati. Minima distanza dai LED 10cmProtezione termica: se la temperatura supera i valori limite, l'alimentatore si disinserisce e dopo pochi secondi si autoripristina.Evitare cortocircuiti sul lato secondario e togliere tensione prima di collegare tutti i LED al sistema. Serrare correttamente la vite dei morsetti senza stringere con troppa forza oppure utilizzare un avvitatore elettrico “a coppia” regolabile.Collegamento dei LED: utilizzare sempre un cavo da 0,5 … 1,5 mm per una lunghezza massima di 10 m. 1,5mm per lunghezze superiori a 10m massimo 30m.USO GRAVOSO : utilizzare un carico inferiore a quello massimo indicato dal 10% al 20% per tutti i tipi di apparecchi . Controllare la temperatura massima di lavoro sul punto tc .
LED Power Supplies- Installation and usage instructions:Always keep attention to the polarity on secondary coil. Install the system in ventilated areas, far away from heat sources. Medium distance from the LEDs: 10cm.Thermal protection: if the temperature exceeds the limit values, the power supply switches itself off and it resets in a few seconds.Avoid short-circuits on secondary coil and turn off power before connecting all the LEDs to the system.Be careful to screw correctly the screw clips, avoiding to fasten them with too much strength, or use an electrical torque screwdriver.LEDs connection: always use a 0,5….1,5mm wire for a maximum of 10m. Use a 1,5mm wire for more than 10m, up to a maximum of 30m.HEAVY USE: for all types of devices, use a 10-20% lower load compared to the maximum one indicated. Control the maximum working temperature on the TC point.
ELCOM srlVia follo 5 D/E - 25070 CAINO (BS) - ITALIA
Tel. 0039 030 6830559Fax 0039 030 6830777
SCHEMA DI CABLAGGIO - WIRING SCHEME
M M F EMC 1..10V PUSHIP20IP20
ALIMENTATORE DIMMERABILE 1..10V / PUSH - cod. 07450
SCHEDA TECNICA Data sheet
Dimmable power supply - costant voltage output 1..10V/PUSH - cod. 07450
100W 24 Vdc IP20IP20ALIMENTATORE DIMMERABILE DALI/1..10V / PUSH - cod. 07453
Dimmable DALI/1..10V/PUSH power supply - costant voltage output - cod. 07453