Upload
tranngoc
View
238
Download
1
Embed Size (px)
Citation preview
Type series booklet1592.551--10 Amamix� direct
Submersible motordriven mixer-- Unit-- Accessories (standard)
50 HzStandard Programme
Areas of applicationIn environmental engineering for the treatment of municipaland industrial sewage/waste water/effluents and sludge.For mixing, homogenizing and thickening-- in sludge storage tanks-- during the thickening process-- in the sludge dewatering process-- to optimise heat transfer-- for the cleaning of pump sumps-- to prevent formation of deposits on tank walls and floor-- to remove floating sludge
Operating dataAmamix� directNominal propeller diameter D 215 mm ... 600 mmPower rating P up to 10 kWFluid temperature T up to 40 oCInstallation depth H up to 30 m
DesignHorizontal submersible motor mixers with ECB propellers inclose-coupled design, direct--driven.
Drive-- Three-phase asynchronous motor 400 V/50 Hz,(Var. 500 V, 690 V)
-- Also in explosionproof design: ATEX II2G EEx d IIB T4
Bearing assemblyMaintenance-free rolling element bearings, sealed for life.
Shaft sealTwo bi-directional mechanical seals, with environmentallyfriendly oil chamber.
MaterialsStandard design in cast iron.Material variants in corrosion and wear-resistant stainlesssteel.
Designation
SeriesMaterial variant of propellerNominal propeller diameter codeNo. of bladesBlade angle codeMotor sizeNo. of polesMotor designMaterial variant of unit
Amamix C 635 / 8 12 YM C
Amamix� direct
3
Modular design Amamix directNominal propeller diameter
215
300
400
500/600
1 4/2 4
1 6/2 6
2 8/4 8
5 12/6 12/9 12/10 12Material variant G3 12/4 12/7 12/8 12Material variant C
Motor size
T 0294-457712 F 0294-457713 [email protected]
Amamix� direct
4
Product advantagesExample: Amamix 400 G
Absolutely watertight cable entry
Your benefit:Even if the cable sheath and core in-sulation are damaged, no moisturecan penetrate into the motor spacealong the strands as a result ofcapillary action.
2 bi-directional mechanical seals,with silicon-carbide contact faces andjoint liquid supply.
Your benefit:Long operating life by providingdouble safety. Should one mechanicalseal fail, then the second one willcontinue to provide complete unitprotection.
0W 386 417--00
Thick--walled motor housing made ofJL 1040
Dry, fully submersible squirrel-cagemotor.Thermal class F, also explosion-proofto ATEX 2 IIG EEx d IIB T4.A motor of optimum design.
Your benefit:The optimum motor designguarantees maximum reliability
Your benefit:Long-term protection from corrosionand abrasion, good thermalconduction
Your benefit:The motor cannot be damaged byoverheating.
Temperature sensors preventexcessive heat in the motor winding.
Your benefit:High reliability at lowmaintenance and service costs,long service intervals
Sturdy bearings lubricated for lifetime
Your benefit:Low energy costs combinedwith high reliability
ECB propeller designoptimised with regardto efficiency
Oil reservoir filled withenvironmentally harmless oil
Your benefit:Any oil leaking into theenvironment is ecologicallyharmless.
All bolts in stainless steel
Your benefit:A small detail which makesthe unit very service-friendly.Easily dismantled even afteryears of operation.
Universal mounting clamp
Your benefit:Allows for customisedinstallation and positioning
T 0294-457712 F 0294-457713 [email protected]
Amamix� direct
5
Product advantagesExample: Amamix 600 C
Absolutely watertight cable entry
Your benefit:Even if the cable sheath and core in-sulation are damaged, no moisturecan penetrate into the motor spacealong the strands as a result ofcapillary action.
0W 384 103--00
Thick--walled stainless steel motorhousing (material variant C)
Dry, fully submersible squirrel-cagemotor.Thermal class F, also explosion-proofto ATEX 2 IIG EEx d IIB T4.A motor of optimum design.
Your benefit:The optimum motor designguarantees maximum reliability
Your benefit:Long-term protection from corrosionand abrasion, good thermalconduction
2 bi-directional mechanical seals,with silicon-carbide contact faces andjoint liquid supply.
Your benefit:Long operating life by providingdouble safety. Should one mechanicalseal fail, then the second one willcontinue to provide complete unitprotection.
Your benefit:The motor cannot be damaged byoverheating.
Temperature sensors preventexcessive heat in the motor winding.
Your benefit:High reliability at lowmaintenance and service costs,long service intervals
Sturdy bearings lubricated for lifetime
Your benefit:Low energy costs combinedwith high reliability
ECB propeller designoptimised with regardto efficiency
Oil reservoir filled withenvironmentally harmless oil
Your benefit:Any oil leaking into theenvironment is ecologicallyharmless.
All bolts in stainless steel
Your benefit:A small detail which makesthe unit very service-friendly.Easily dismantled even afteryears of operation.
Universal mounting clamp
Your benefit:Allows for customisedinstallation and positioning
T 0294-457712 F 0294-457713 [email protected]
Amamix� direct
7
0W 384 103--00
Motor housing cover
Propeller
Shaft
Supportingclamp
Clamp
Motor housing
Casing cover
0W 384 961--61
Jet ring
Material variantPart Material variant
G C
Pump UnitMotor housing JL 1040 1.4581Motor housing cover JL 1040 1.4517Casing cover JL 1040 1.4571Propeller Amamix 215 PU 1.4571p
other sizes 1.4571Mechani-cal seal
propellerside
SiC / SiC
motor side SiC / SiCShaft 1.4571
(Amamix 600 G in 1.4021)
O-rings Viton (FPM)Bolts A4 (as1.4571)Clamp JL 1040 1.4571Supporting clamp 1.4571Jet ring (option) -- 1.4571
Materials
Material comparisonEN Similar to ASTM material
JL 10 40 A 48 Class 35 B1.4517 A 743 CD 4 MCU1.4571 / 1.4581 A 276 Type 316 Ti1.4021 A 276 Type 420PU (Polyurethane) PolyurethaneFPM FKM
JL 1040 GG-25
Oil fill for mech. seal reservoirAmamix 215 G 0.3 lAmamix 215 C 0.4 lAmamix 300 G / C 0.4 lAmamix 400 G / C 0.8 lAmamix 500 / 600 G / C 1.4 l
This graphite cast iron to DIN 1691 is used most commonlyfor pumping municipal sewage, foul water, sludges andstorm and surface water. It is suitable for neutral andslightly aggressive media.The pH-value should be² 6.5; and the sandcontent± 0.5 g/l.
The resistance to pitting of this ferritic-austenitic stainlesscast steel makes it particularly suitable to pump sewage con-taining substantial amounts of chlorides and acids or sea andbrackish water.Its good chemical resistance, even to phosphorus and sul-phur, makes it suitable for wide application in the chemicaland process industries.Units manufactured in duplex steel have also been used verysuccessfully to pump brine and chemical effluents (pH 1--12),foul water and seepage from waste tips.
Duplex SteelCast Stainless steel
(1.4517 or technically equivalent material)
Grey Cast Iron JL 1040 (GG-25)Graphite cast iron
This austenitic steel acc. to DIN 17 440 is highlycorrosion-resistant in municipal and chemicaleffluent and is more resistant against intercrystallinecorrosion due to its titanium stabilisation even whenwelded.
1.4571 / 1.4581 (X10 CrNiMoTi 18 10)Austenitic steel
T 0294-457712 F 0294-457713 [email protected]
Amamix� direct
10
General drawing with list of components (material variant G)
Example: Amamix C 435/4 8 UDG
AA
515
932.05932.04914.01
550.01411.02903.02 412.01
161
412.05
932.01
81--59
561903.01411.01
433.02 932.03321.01932.02
433.01 441 59--1759--31
818
914.0469--14
914.02
412.03
421.03
81--51412.04834 914.03 812
732
421.01
322
529
932.07
443
811
Amamix 400 ... 600Standard:
Amamix 300Option:
OW 384 103-00
901.01930
596
81--39 901.02
A
Amamix 215, 300
321.02
Option:
Part No. Part description Part No. Part description Part No. Part description
161 Casing cover 529 Bearing sleeve 80-1 Motor housing with stator23-9 Propeller 550 Disc 812 Motor housing cover321 Radial ball bearing 561 Grooved pin 818 Rotor322 Radial roller bearing 59-17 Shackle 834 Cable entry411 Joint ring 59-31 Supporting clamp 903 Screwed plug412 O-ring 69-14 Leakage sensor 914 Socket hd. cap screw421 Radial shaft seal ring 732 Clamp 932 Circlip433 Mechanical seal441 Housing for shaft seal
T 0294-457712 F 0294-457713 [email protected]
Amamix� direct
11
General drawing with list of components (material variant C)
Example: Amamix C 635/8 12 YMC
59--17
932.04914.01
550.01
412.02932.05411.02903.02 412.01 932.06
69--14 932.01
412.05
23--9433.02
932.03
433.01411.01903.01
161 561 932.02
441
321.01
330
914.02
80--1
421.02
412.03
914.04
69--14 322
812412.04818
59--31 515
914.03
834 81--51 732
932.07
529
421.01
443
OW 384 103-00
Covered bellows-type mechanical seal-- for Amamix 400, 500, 600 standard-- for Amamix 300 option
421.01
443
Part No. Part description Part No. Part description Part No. Part description
161 Casing cover 443 Seal insert 80-1 Motor housing with stator23-9 Propeller 515 Taper lock ring 812 Motor housing cover321 Radial ball bearing 529 Bearing sleeve 818 Rotor322 Radial roller bearing 550 Disc 834 Cable entry330 Bearing bracket 561 Grooved pin 903 Screwed plug411 Joint ring 59-17 Shackle 914 Socket hd. cap screw412 O-ring 59-31 Supporting clamp 932 Circlip421 Radial shaft seal ring 69-14 Leakage sensor433 Mechanical seal 732 Clamp441 Housing for shaft seal
T 0294-457712 F 0294-457713 [email protected]
Amamix� direct
12
Technical data
Amamix 215 400 V, 50 Hz n~1400 min--1
Version without jet ring
Performance data, material variant GNo. Size Motor
powerWeight
incl.clamp + 10 m
P2clamp + 10 mpower cable
Amamix ... [kW] [kg]
01 V 222/1 4 UDG/YDG 1.25 32
02 V 222/2 4 UDG/YDG 1.6 34.5
03 V 233/2 4 UDG/YDG 2.5 34.5
04 V 235/2 4 UDG/YDG 2.5 34.5
Min. dimensions of access openingSquare guide rail
APropeller with no. of blades
z=2 z=3
60
60
3
34
N
M
A
� D
L
T S
� 18
H
B
A
�G
150
Dimensions tableSize Dimensions [mm]
Amamix ... A B � D � G H L M / z=2 M / z=3 N S T
V 2 ... /1 4 UDG/YDG 590 460 ~225 156 290 520 300 350 800 210 240
V 2 ... /2 4 UDG/YDG 215 235
T 0294-457712 F 0294-457713 [email protected]
Amamix� direct
13
Amamix 215 400 V, 50 Hz n~1400 min--1
Version without jet ring
Performance data, material variant CNo. Size Motor
powerWeight
incl.clamp + 10 m
P2clamp + 10 mpower cable
Amamix ... [kW] [kg]
01 C 222/1 4 UMC/YMC 1.25 34.5
02 C 222/2 4 UMC/YMC 1.6 37
03 C 224/2 4 UMC/YMC 2.5 37
04 C 235/2 4 UMC/YMC 2.5 37
Min. dimensions of access openingSquare guide rail
APropeller with no. of blades
z=2 z=3
60
60
3
34
N
M
A
� D
L
T S
� 18
H
B
A
�G
150
Dimensions tableSize Dimensions [mm]
Amamix ... A B � D � G H L M / z=2 M / z=3 N S T
C 2 ... /1 4 UMC/YMC 590 460 ~225 148 290 520 300 350 800 220 200
C 2 ... /2 4 UMC/YMC 225 195
T 0294-457712 F 0294-457713 [email protected]
Amamix� direct
14
Amamix 300 400 V, 50 Hz n~920 min--1
Version without jet ring
Performance data, material variant GNo. Size Motor
powerWeight
incl.clamp + 10 m
P2clamp + 10 mpower cable
Amamix ... [kW] [kg]
01 C 322/1 6 UDG/YDG 1.8 44
02 C 322/2 6 UDG/YDG 2.2 53.5
03 C 324/2 6 UDG/YDG 3.2 53.5
04 C 335/2 6 UDG/YDG 3.2 57.5
Performance data, material variant CNo. Size Motor
powerWeight
incl.clamp + 10 m
P2clamp + 10 mpower cable
Amamix ... [kW] [kg]
01 C 322/1 6 UMC/YMC 1.8 38
02 C 322/2 6 UMC/YMC 2.2 47
03 C 324/2 6 UMC/YMC 3.2 47
04 C 335/2 6 UMC/YMC 3.2 47
L
T S
� 18
� D
A
APropeller with no. of blades
z=2 z=3
60
60
3
Square guide rail
34
N
M
H
B
A
�G
Min. dimensions of access opening
150
Dimensions tableSize Dimensions [mm]
Amamix ... A B � D � G H L M / z=2 M / z=3 N S T
C 3 ... /1 6 U .. /Y .. 580 450 ~315 148 G 290 510 300 400 800 225 195
C 3 ... /2 6 U .. /Y .. 650 520 156 C 580 850 260 230
T 0294-457712 F 0294-457713 [email protected]
Amamix� direct
15
Amamix 400 400 V, 50 Hz n~700 min--1
Version without jet ring
Performance data, material variant GNo. Size Motor
powerWeight
incl.clamp + 10 m
P2clamp + 10 mpower cable
Amamix ... [kW] [kg]
01 C 422/2 8 UDG/YDG 2.5 84
02 C 422/4 8 UDG/YDG 3.0 91
03 C 424/4 8 UDG/YDG 4.0 91
04 C 435/4 8 UDG/YDG 4.0 91
Performance data, material variant CNo. Size Motor
powerWeight
incl.clamp + 10 m
P2clamp + 10 mpower cable
Amamix ... [kW] [kg]
01 C 422/2 8 UMC/YMC 2.5 76
02 C 422/4 8 UMC/YMC 3.0 84
03 C 424/4 8 UMC/YMC 4.0 84
04 C 435/4 8 UMC/YMC 4.0 84
L
T S
� 18
� D
A
APropeller with no. of blades
z=2 z=3
100
100
5
Square guide rail
44
N
M
H
B
A
�G
Min. dimensions of access opening
180
Dimensions tableSize Dimensions [mm]
Amamix ... A B � D � G H L M / z=2 M / z=3 N S T
C 4 ... /2 8 U .. /Y .. 790 605 ~400 186 G192 C
420 695 400 500 1000 305 285
C 4 ... /4 8 U .. /Y ..192 C
315 275
T 0294-457712 F 0294-457713 [email protected]
Amamix� direct
16
Amamix 500 400 V, 50 Hz n~475 min--1
Version without jet ring
Performance data, material variant GNo. Size Motor
powerWeight
incl.clamp + 10 m
P2clamp + 10 mpower cable
Amamix ... [kW] [kg]
01 C 522/5 12 UDG 3.0 219
02 C 523/6 12 UDG 5.0 219
Performance data, material variant CNo. Size Motor
powerWeight
incl.clamp + 10 m
P2clamp + 10 mpower cable
Amamix ... [kW] [kg]
01 C 522/3 12 UMC/YMC 3.0 144
02 C 523/4 12 UMC/YMC 5.0 144
L
T S
� 18
� D
A
APropeller with no. of blades
z=2
100
100
5
Square guide rail
44
N
M
H
B
A
�G
Min. dimensions of access opening
215C
230G
Dimensions tableSize Dimensions [mm]
Amamix ... A B � D � G H L M / z=2 M / z=3 N S T
C 5 ... /5 12 UDG 960 755 ~550 294 507 855 450 600 1100 420 330
C 5 ... /6 12 UDG
C 5 ... /3 12 UMC/YMC 860 675 ~550 251 420 765 450 600 1100 360 270
C 5 ... /4 12 UMC/YMC
T 0294-457712 F 0294-457713 [email protected]
Amamix� direct
17
Amamix 600 400 V, 50 Hz n~475 min--1
Version without jet ring
Performance data, material variant GNo. Size Motor
powerWeight
incl.clamp + 10 m
P2clamp + 10 mpower cable
Amamix ... [kW] [kg]
01 C 622/6 12 UDG 5.0 221
02 C 622/9 12 UDG 7.5 235
03 C 624/10 12 UDG 10.0 235
04 C 635/81012 UDG 10.0 237
Performance data, material variant CNo. Size Motor
powerWeight
incl.clamp + 10 m
P2clamp + 10 mpower cable
Amamix ... [kW] [kg]
01 C 622/4 12 UMC/YMC 5,0 146
02 C 622/7 12 UMC/YMC 7.5 198
03 C 624/8 12 UMC/YMC 10.0 198
04 C 635/8 12 UMC/YMC 10.0 198
L
T S
� 18
� D
A
APropeller with no. of blades
z=2 z=3
100
100
5
Square guide rail
44
N
M
H
B
A
�G
Min. dimensions of access opening
215C
230G
Dimensions tableSize Dimensions [mm]
Amamix ... A B � D � G H L M / z=2 M / z=3 N S T
C 6 ... /6 12 UDG 960 755 ~630 294 507 855 500 700 1100 420 330
C 6 ... /9 12 UDG
C 6 ... /10 12 UDG
C 6 ... /4 12 UMC/YMC 860 675 ~630 251 420 765 500 700 1100 360 270
C 6 ... /7 12 UMC/YMC 980 795 885 1250 420 330
C 6 ... /8 12 UMC/YMC
T 0294-457712 F 0294-457713 [email protected]
Amamix� direct
18
Amamix 300 400 V, 50 Hz n~920 min--1
Version with jet ring
Material variant C
0W 384 961--30
M
C
N
34
B
A
KH
60
60
3
L
T
18
S
Z=2
Z=3
�D�
E
�G
�F
Min. dimensions of access opening
Square guide rail
Propeller with jet ring
A
A
Propeller with jet ringA
Dimensions tableSize Dimensions [mm]
Amamix ... A B C � D � E � F � G H K L M N S T
C 3 ... /1 6 UMC/YMC 620 490 20 ~315 350 460 148 290 150 550 550 830
C 3 ... /2 6 UMC/YMC 690 560 620 550
Extra weight for jet ring (see table page 14) approx. 6 kg
T 0294-457712 F 0294-457713 [email protected]
Amamix� direct
19
Amamix 400 400 V, 50 Hz n~700 min--1
Version with jet ring
Material variant C
0W 384 961--40
S
M
N
B
A
C
L
T
18
100
44
100
5
K
H
Z=2
Z=3
�D�
E
�G
�F
Min. dimensions of access opening
Square guide rail
Propeller with jet ring
A
A
Propeller with jet ringA
Dimensions tableSize Dimensions [mm]
Amamix ... A B C � D � E � F � G H K L M N S T
C 4 ... /2 8 UMC/YMC 830 645 35 ~400 450 585 186 420 180 735 700 1050
C 4 ... /4 8 UMC/YMC
Extra weight for jet ring (see table page 15) approx. 8.7 kg
T 0294-457712 F 0294-457713 [email protected]
Amamix� direct
20
Amamix 500 400 V, 50 Hz n~475 min--1
Version with jet ring
Material variant C
0W 384 961--50
M
A
N
44
100
100
5
C*
B
18K
H
L
T S
Z=2
Z=3
�D�
E
�G
�F
Min. dimensions of access opening
Square guide rail
Propeller with jet ring
A
A
Propeller with jet ringA
Dimensions tableSize Dimensions [mm]
Amamix ... A B C � D � E � F � G H K L M N S T
C 5 ... /3 12 UMCYMC 930 745 35 ~550 600 775 251 420 215 835 900 1175
C 5 ... /4 12 UMC/YMC
Extra weight for jet ring (see table page 16) approx. 18 kg
T 0294-457712 F 0294-457713 [email protected]
Amamix� direct
21
Amamix 600 400 V, 50 Hz n~475 min--1
Version with jet ring
Material variant C
0W 384 961--60
M
N
B
A
C
18
T
L
S
44
100
100
5
K
H
Z=2
Z=3
�D�
E
�G
�F
Min. dimensions of access opening
Square guide rail
Propeller with jet ring
A
A
Propeller with jet ringA
Dimensions tableSize Dimensions [mm]
Amamix ... A B C � D � E � F � G H K L M N S T
C 6 ... /4 12 UMC/YM ... 930 745 75 ~630 700 900 251 420 215 835 1050 1175
C 6 ... /7 12 UMC/YMC 1050 865 955 1300
C 6 ... /8 12 UMC/YMC
Extra weight for jet ring (see table page 17) approx. 24 kg
T 0294-457712 F 0294-457713 [email protected]
Amamix� direct
23
Overview of standard accessories
Accessories Typeseries
Installation example
215
300
400
500/600
Standard accessories 6Page 24--25
Floor mounting
x x -- ---- swivelling option inhorizontal position
-- fixed vertical installation height
Standard accessories 7Page 26--29
Sump installation
x x -- --
-- vertically adjustable
-- with optional pitch adapter forupward and downwardjet positioning
-- cannot be swivelled horizontallyaround the guide rail axis
Standard accessories 21Page 30--31
Accessories 21-- OptionsPage 32--39
Universal accessories
x x x x
-- vertically adjustable
-- with optional pitch adapter forupward and downwardjet positioning
-- horizontal swivelling option(together with guide rail)
Standard accessories 4
Page 40--41x x x x
Guide railsfor accessories 7 and 21
Page 43
x x x x
Other accessoriesPage 42 x x x x
Cranes See Type series booklet “KSB Lifting Equipment” 1596.5--10 !
T 0294-457712 F 0294-457713 [email protected]
Amamix� direct
24
Standard accessories 6For permanent mounting of the mixer on the tank floorAmamix 215, 300 (Size 400/500/600 on request)
Hole diameter 18 mmHole depth 125 mmMax. tightening torque 80 Nm
Ha adjustable to 161 mm / 175 mm / 196 mm / 213 mm,depending on propeller diameter
Installation example:Floor mounting
UG 1035 496
6297
207
AB
94
C1
Ha
Hb
Øda
min.175
65
300347
ØD
Nmin
150
Pmin
15�15�Min. dimensions for installation through accessopening (jet position 0�)
Jet angle +15�
Dimensions tableSize Dimensions [mm] Weight of unit
without stand with stand
Amamix ... A B C1 � D � da Ha Hb Pmin Nmin 1) [kg] [kg]
V 222 / 14 ..DG 560 466 124 ~ 225 156 161 48,5 610 400 28 34V 222 / 24 ..DG 30.5 36.5V 233 / 24 ..DGV 235 / 24 ..MGC 222 / 14 ..DC 560 466 120 ~ 225 148 161 48,5 610 400 30.5 36.5C 222 / 24 ..MC 33 39C 233 / 24 ..MCC 235 / 24 ..MCC 322 / 16 ..MG 538 444 124 ~ 315 156 213 55.5 600 400 38 34C 322 / 26 ..DG 610 516 660 48 54C 324 / 26 ..DGC 335 / 26 ..DGC 322 / 16 ..MC 538 444 120 ~ 315 148 213 55.5 600 400 34 40C 322 / 26 ..MC 610 516 660 43 49C 324 / 26 ..MCC 335 / 26 ..MC
Extra weight for stand: 6 kg (if supplied pre--assembled)
T 0294-457712 F 0294-457713 [email protected]
Amamix� direct
25
Standard accessories 6For permanent mounting of the mixer on the tank floorAmamix 215, 300
Item No. Accessories Description
6 Stand for permanent mounting of the mixer (sizes 215, 300) on the tank floor;application in tanks where regular drainage provides access to the unit(e.g. for maintenance and inspection purposes),e.g. stormwater balancing systems.
Incl. composite anchorbolts
Composite anchor bolts for fastening the stand on the tank floor(concrete grade at least B25)
Item No. Description For size Material Material No. Weight[kg]
6 Standincl 3 nos composite anchor bolts
Amamix 215/300 1.4301 01 109 062 8.0incl. 3 nos. composite anchor bolts
1.4571 19 556 921 8.0
T 0294-457712 F 0294-457713 [email protected]
Amamix� direct
26
Standard accessories 7For mounting on the sump wall or benching, vertically adjustableAmamix 215, 300
UG 1035 864
Installation example:Wall-mounted(optional lifting clamp)
Min. dimensions for installation through accessopening (jet position 0�)
7 OH
4 KTR
FB
21 HW7 UH
Hole diameter 18 mmHole depth 125 mmMax. tightening torque 80 Nm
Hole diameter 18 mmHole depth 125 mmMax. tightening torque 80 Nm
Other dimensions are given on page 28
40
200
150
C1
C2
� D
120
60
130
180
110 110
8020
20min.100
120
60x60x3
H2
150
230
80
�da
A
B
150
min. 175
65 S T
L
F
120
�dm
Pmin
Nmin
36
T 0294-457712 F 0294-457713 [email protected]
Amamix� direct
27
Standard accessories 7For mounting on the sump wall or benching, vertically adjustableAmamix 215, 300
UG 1035 913
Installation example:on benching(optional lifting clamp)
Hole diameter 18 mmHole depth 125 mmMax. tightening torque 80 Nm
7 OH
4 KTR
FB
21 HW
7 UH
Hole diameter 18 mmHole depth 125 mmMax. tightening torque 80 Nm
Other dimensions are given on page 28
min. 175 120min.100 65
L
60x60x3
80 AB
150
C1
C2
230
H2
F
jda
40
200
150
�D
130180
110
20
�dm
Pmin
Nmin
36
110
e.g. 30o
Min. dimensions for installation through accessopening (jet position 0�)
T 0294-457712 F 0294-457713 [email protected]
Amamix� direct
28
Standard accessories 7For mounting on the sump wall or benching, vertically adjustableAmamix 215, 300
Dimensions tableSize Dimensions [mm] Weight of pump unit 1)
Amamix ... A B C1 C2 � D � da � dm F H2 L S T Pmin Nmin [kg]
V 222 / 14 ..MG 597 460 124 164 ~ 225 156 187 42 287 525 210 240 650 300 35V 222 / 24 ..MG 215 235 37.5V 233 / 24 ..MG 350V 235 / 24 ..MGC 222 / 14 ..MC 590 460 120 260 ~ 225 148 187 34 290 539 220 220 640 300 34C 222 / 24 ..MC 225 195 36.5C 233 / 24 ..MC 350C 235 / 24 ..MCC 322 / 16 ..MG 597 450 124 264 ~ 315 156 187 42 287 515 225 195 640 300 45C 322 / 26 ..MG 657 520 585 260 230 710 55C 324 / 26 ..MGC 335 / 26 ..MG 400C 322 / 16 ..MC 580 450 120 260 ~ 315 148 187 34 290 529 225 195 630 300 37.5C 322 / 26 ..MC 650 520 599 260 230 700 46.5C 324 / 26 ..MCC 335 / 26 ..MC 400
1) Weight of unit with 10--metre power cable and assembled clamp
Item No. Accessories Description
21 HT Clamp Clamp for mounting the unit on the square guide rail in horizontal position,Cross-section: 60x60x3
21 HW Holding bracket vertical continuous adjustment to the operating position of the mixer;Unit rests on the bracket via the clamp.
4 KTR Square guide rail Square guide rail (see page 43!)Cross-section: 60x60x3
Supplied in lengths of 1.5 m / 3 m / 6 m
7 UH Lower guide rail holder Lower holder for mounting the guide rail on the sump wall or benching; infini-tely adjustable through 90o
incl. 2 nos. compositeanchor bolts
Composite anchor bolts for fitting the lower holder on the sump wall or ben-ching
Concrete grade at least B25.
7 OH Upper guide rail holder Upper holder for mounting the guide rail on the sump wall; flexible support of60x60x3 guide rail
incl. 2 nos. compositeanchor bolts
Composite anchor bolts for mounting the upper holder on the sump wall
Concrete grade at least B25.
T 0294-457712 F 0294-457713 [email protected]
Amamix� direct
29
Standard accessories 7For mounting on the sump wall or benching, vertically adjustableAmamix 215, 300
Item No. Description for size Material Material No. Weight[kg]
21 HT Clamp for square guide rail 60x60x3 Amamix 215/300 G JL 1040 19 203 139 6.9
Amamix 215/300 C 1.4571 19 202 241 2) 3.4
21 HW Bracket for square guide rail 60x60x3 Amamix 215/300 1.4301 01 109 104 1.5
1.4571 19 202 369 1.5
4 KTR Square guide rail 60x60x3 Amamix 215/300 1.4301 ---- 5.2 kg/m
1.4571
See accessories Amamix -- 4 KTR -- page 43!
2) optional for Amamix 215/300 G
T 0294-457712 F 0294-457713 [email protected]
0W 384 395--00
Installation example:Mounted on the tank edge
Square guide rail60x60x3: Amamix 215/300100x100x5: Amamix 400/500/600(not generally included in KSB’s scopeof supply)
A
Installation example:Mixer swivelled through 45o(can be turned through 360o, dependingon installation)
21 HW
B
B
4 KTR
21 HT
21 GR
A
Installation example:Horizontal tank floor
C
C
M
min.120
200 L
S
N
Min. dimensions for installing the unitthrough cover opening.
200
150
150
200
200
200
Dimensions L, S, N and Msee dimensions tables, page 12--17
AB
C
Max.istallationdepthwithoutm
iddlesupportforguiderail:6m;
middlesupportrequiredforinstallationdepths
>6m
Amamix� direct
30
Standard accessories 21For mounting on the top of the tank or tank wall, with horizontal swivelling option, vertically adjustableAmamix 215, 300, 400, 500, 600
Dimensions tableSize Dimensions [mm]
Amamix ... A B C
215 G, 300 G 150 110 124
215 C, 300 C 120
400 G 180 150 142
400 C 140
500/600 G 230 197
500/600 C 215 177
T 0294-457712 F 0294-457713 [email protected]
Amamix� direct
31
Standard accessories 21For mounting on the top of the tank or tank wall, with horizontal swivelling option, vertically adjustableAmamix 215, 300, 400, 500, 600
Item No. Accessories Description
21 HT Clamp Clamp for mounting the unit on the square guide rail in horizontal positionCross-section: 60x60x3 for Amamix 215/300 and
100x100x5 for Amamix 400/500/600
21 HW Holding bracket vertical continuous adjustment to the operating position of the mixer; unitrests on the bracket via the clamp.
4 KTR Square guide rail Square guide railCross-section: 60x60x3 for Amamix 215/300 and
100x100x5 for Amamix 400/500/600;
Installation depths up to 6 m without middle support;middle support required for installation depths >6 m
See page 43!
21 GR Upper and lower holdersfor guide rail
Upper holder for mounting on the tank wall;lower holder for horizontal tank floor without benching
Incl. 6 nos. compositeanchor bolts
Composite anchor bolts for mounting the upper holder on the tank wall andthe lower holder on the tank floor.Concrete grade at least B25.
Item No. Description for size Material Material No. Weight[kg]
21 HT Clamp for square guide rail 60x60x3 Amamix 215/300 G JL 1040 19 203 139 6.9
Amamix 215/300 C 1.4571 19 202 241 1) 3.4
Clamp for square guide rail 100x100x5 Amamix 400 G JL 1040 19 556 701 16
Amamix 500/600 G JL 1040 19 556 700 25
Amamix 400/500/600 C 1.4571 19 202 242 2) 8.5
21 HW Clamp for square guide rail 60x60x3 Amamix 215/300 1.4571 19 202 369 1.5
Clamp for square guide rail 100x100x5 Amamix 400/500/600 1.4571 19 202 370 3.5
4 KTR Square guide rail 60x60x3 Amamix 215/300 1.4301/1.4571
---- 5.2 kg/m
Square guide rail 100x100x5 Amamix 400/500/600 1.4301/1.4571
---- 14.4 kg/m
Please note accessories Amamix -- 4 KTR -- page 43!
21 GR Top wall and floor holders, vertical wall,for square guide rail 60x60x3incl. 6 nos. of composite anchor bolts
Amamix 215/300 1.4571 19 553 874 9.0
Top wall and floor holders, vertical wall,for square guide rail 100x100x5
Amamix 400/500 1.4571 19 553 875 12.5for square guide rail 100x100x5incl. 6 nos. of composite anchor bolts Amamix 600 1.4571 01 110 318 17
1) optional for Amamix 215/300 G2) optional for Amamix 400 G
T 0294-457712 F 0294-457713 [email protected]
Amamix� direct
32
Accessories 21 -- OptionsFor mounting on the top of the tank or tank wall, with horizontal swivelling option, vertically adjustableAmamix 215, 300, 400, 500, 600
Installation example:Middle supportfor guide rail
L1
Ltotal
0W 384 395--00
Installation example:Upper holder mounted on bracket(top of tank)
Installation example:Wall-mounted with bracket
21 SBB/UWB
21 KBR
Installation example:Bracket for floor inclines 0o ... 90o
Middle support for guide rail
B
B
21 MIAS
120
222
120
120 120 200
200 200
200
L1 should be located as closelyabove the mixer as possible, toensure that the forces generatedare safely transferred from theguide rail into the wall!
T 0294-457712 F 0294-457713 [email protected]
Amamix� direct
33
Accessories 21 -- OptionsFor mounting on the top of the tank or tank wall, with horizontal swivelling option, vertically adjustableAmamix 215, 300, 400, 500, 600
Item No. Accessories Description
21 KBR Additional bracket(top of tank)
For mounting on the top of the tank, holding the upper holder of the guide rail
incl. 2 additionalcomposite anchor bolts
Composite anchor bolts for mounting upper holder on the top of the tank(concrete grade at least B25)
21 SBB/UWB Additional bracket(lower wall mounting/inclined tank floor)
Used for inclined tank floors or for lower wall mounting, e.g. above existingwall berms or aerators; adjustable from 0o to approx. 90o
21 MIAS Middle support forsquare guide rail
For supporting the square guide rail on the tank wall in case of installationdepths² 6 m;Guide rails up to 6 m long do not generally require a middle support, exceptfor tanks where the set jet direction and wall reflections (e.g. as a result oftank shape and installations) result in increased forces acting on the guiderail and upper and lower holders. In this case a middle support must beprovided for the guide rail, like for guide rails >6 m.
Incl. 4 nos. compositeanchor bolts
Composite anchor bolts for mounting the middle support on the croncretetank wall;concrete grade at least B25
Item No. Description for size Material Material No. Weight[kg]
21 KBR Additional bracket for upper wallmounting, incl. 2 additional compositeanchor bolts
Amamix 215 ... 600 1.4571 19 553 876 16.0
21SBB/UWB
Additional bracket for inclined tankfloors or lower wall mounting
Amamix 215 ... 600 1.4571 19 553 842 22.7
21MIAS
Middle supportfor square guide rail 60x60x3
Amamix 215/300 1.4571 19 553 877 6.9
Middle supportfor square guide rail 100x100x5
Amamix 400/500/600 1.4571 19 553 878 9.8
all incl. 4 nos. composite anchor bolts
T 0294-457712 F 0294-457713 [email protected]
Amamix� direct
34
Accessories 21 -- OptionsAmamix 215 and 300 with clamp for guide rail 100x100
The standard version of Amamix 215/300 with accessories set no. 21 is designed for the (square) guide rail measuring 60x60x3(new installations).
If a square guide rail 100x100 has been specified, or if a square guide rail 100x100 is already installed (e.g. in the case of KSBreplacement units), Amamix 215/300 units can be retrofitted with the following clamps instead of the standard clamps:
-- Amamix 215/300 material variant G -- Clamp 19 556 701-- Amamix 215/300 material variant C -- Clamp 19 202 242
The clamp is already provided with the holes required for fastening the Amamix 215/300 unit.Mounting to the motor housing cover: 4 cheese--head screws M8; tightening torque 17 Nm.
Compared to the technical data given in the type series booklet for the standard version (clamp for square guide rail 60x60x3)(dimensions sheet), the complete unit weight, incl. clamp and 10--metre power cable, will be increased by 9.1 kg (”G” variant) or5.1 kg (”C” variant).
The heavy bracket also alters dimensions A and H as well as the position of the supporting clamp, as shown in the table on thenext page.All dimensions not listed in the table remain the same.
Please note:Holding brackets already mounted on the guide rail (for adjusting the unit’s distance from the floor) do not need to be replaced.Once the unit is lowered, it will rest on these brackets via the flexible rubber buffers mounted on the clamp.
T 0294-457712 F 0294-457713 [email protected]
Amamix� direct
35
Accessories 21 -- OptionsAmamix 215 and 300 with clamp for guide rail 100x100
Square guide rail
100
100
5
T S
H
A
T S
H
A
T S
H
A
215 G
215 C
300 G/C
180
180
180
�156
�148
�156(G)
�148(C)
Dimensions tableSize Dimensions [mm]
Amamix ... A H S T
V 2 ... /1 4 UDG/YDG270
V 2 ... /2 4 UDG/YDG645
215270
C 2 ... /1 4 UMC/YMC645
405240
C 2 ... /2 4 UMC/YMC405
220 235
C 3 ... /1 6 UDG/YDG / UMC/YMC 635 225 230
C 3 ... /2 6 UDG/YDG / UMC/YMC 705 265 260
T 0294-457712 F 0294-457713 [email protected]
Amamix� direct
36
Accessories 21 -- OptionsPitch adapter for Amamix 215 ... 600 (except 500/600 G !)
The standard clamp (made of JL1040 in material variant G; 1.4571 in material variant C)-- item 21 HT (see table on page 31) --does not allow an inclined mixer position relative to the guide rail axis.
For such duties (requiring an upward or downward inclination of the mixer jet) an adapter -- item 21 ADP -- is required.This adapter is fitted between the motor housing cover and the clamp. It enables the requisite inclination of the unit axis inincrements of 10o, from 40o upwards to 40o downwards.(Exception: Amamix 600 C -- max. upward and downward pitch of 30o, respectively)
Item No. Description for sizes Material Material No. Weight[kg]
21 ADP Pitch adapter Amamix 215/300 G
Amamix 215/300 C
1.4571 19 554 654 4.0
Amamix 400 G/C
Amamix 500/600 C withmotor 312/412/712
1.4571 19 554 656 9.0
Amamix 600 C withmotor 812
1.4571 19 554 655 9.0
Amamix 500/600 G ---- ---- ----
Pitch adaptation is not possible on Amamix 500/600 G !
On Amamix 600 G, the clamp 19 202 242 (which is used as standardclamp on Amamix 400 C and 600 C) cannot be mounted on the motorhousing cover due to different connection dimensions.
Installation of the pitch adapter is shown on page 37.
Note: On the ”C” variant, the adapter can be mounted on the standard clamp in 1.4571 without any problems.On the ”G” variant, the adapter cannot be mounted on the standard clamp in JL1040!In this case, the following clamps made of 1.4571 must be used instead of the standard clamp:-- Amamix 215 and 300: Clamp Mat. No. 19 202 241-- Amamix 400: Clamp Mat. No. 19 202 242
Pitch adaptation between 0o and 40o in steps of 10o will change dimension L, compared to horizontal mixer installation(cf. dimensions tables, pages 12 to 17); also, the position of the supporting clamp (sling point for lifting and lowering the unit) willbe changed.
When themixer is pitcheddownwards (seepage39), itmaynotbepossible to shift the supportingclamp towards themotorhousingcover far enough to still allow smooth lifting and lowering of the mixer (approx. 5o inclination of the clamp).In suchcases, thesupporting strapshownmust beused (included in theadapter assembly),whichprovides theuserwithasuitablesling point. The requisite sling point is determined by the specified hole.
e.g.: Unit V222/14 UMG � corresponds to the following data given in the table on page 39 (downward pitch)
� V2... / 14... � Column Angle 20o “downward”� Column Tu -- 2.L* ~ suspension strap needed � suspend unit from the 2nd hole from the left.
The electrical connection cable is to be fixed with the flexible tubing and cable connectors included in the supply, and is thusprotected (a.o. against chafing).
The applicable dimensions according to pitch direction and angle are listed in the tables on the following pages:-- Pitch adjusted in upward direction page 38-- Pitch adjusted in downward direction page 39
T 0294-457712 F 0294-457713 [email protected]
Amamix� direct
37
Accessories 21 -- OptionsPitch adapter for Amamix 215 ... 600 (except 500/600 G !)
UG 1058 974
Use if adjusting range of supporting clampdoes not provide a suitable sling point.
Pitch adapter (for upward and downward pitchthrough 40� in increments of 10�)
Supporting strap
21 HWHolding bracket
4 KTR
T 0294-457712 F 0294-457713 [email protected]
Amamix� direct
38
Accessories 21 -- OptionsPitch adapter for Amamix 215 ... 600 (except 500/600 G !)Unit with adapter, pitch adjusted in upward direction
Dimensions not indicated here may be gathered fromthe dimension sheets of the relevant mixer size.
Suspend the mixer in the point of gravity or slightly tothe left of it by shifting the supporting clamp. Theangle between clamp and square rail must notexceed 5_.
When mounting the unit, lock all fastening studs ofadapter and supporting clamp with a high--strengthlocking agent (e.g. Loctite 270).
Supportingclamp
Clamp
Adapter
4KTRSquare guide rail
Dimensions table Dimension in mmSize Pitch = 0_ Pitch = 10_ Pitch = 20_ Pitch = 30_ Pitch = 40_
Ho Lo So To Ho Lo So To Ho Lo So To Ho Lo So To Ho Lo So To
V2... /1 4... 260 560 225 265 350 585 240 245 440 595 250 220 520 585 255 190 595 560 260 150V2... /2 4... 260 560 230 260 350 585 245 240 440 595 255 215 520 585 260 185 595 560 260 150C2... /1 4... 270 560 230 230 360 585 250 210 450 595 255 190 530 590 260 165 600 565 260 135C2... /2 4... 270 560 235 225 360 585 255 205 450 595 260 185 530 590 265 160 600 565 260 130C3... /1 6... 320 560 240 220 410 595 260 200 495 615 265 180 570 615 270 155 640 600 265 125C3... /2 6... 320 630 275 255 420 665 295 230 520 680 315 200 605 675 315 170 685 650 305 140C4... /2 8... 460 770 330 320 580 810 350 295 690 830 370 260 795 825 380 220 885 795 380 170C4... /4 8... 460 770 340 310 580 810 360 285 690 830 380 250 795 825 390 210 885 795 390 160C5 22 /4 12... 480 860 400 290 620 920 425 260 750 960 440 225 870 965 445 185
Pit hC5 23 /4 12... 510 860 400 290 645 920 425 260 770 960 440 225 885 965 445 185 Pitchmust not exceed
C6... /4 12... 550 860 400 290 685 930 425 260 810 970 440 225 920 985 445 185must not exceed
30_C6... /8 12... 550 985 460 350 705 1050 485 320 850 1085 500 280 980 1090 505 235
30_
T 0294-457712 F 0294-457713 [email protected]
Amamix� direct
39
Accessories 21 -- OptionsPitch adapter for Amamix 215...600 (except 500/600 G !)Unit with adapter, pitch adjusted in downward direction
Dimensions not indicated here may be gathered fromthe dimension sheets of the relevant mixer size.
Suspend the mixer in the point of gravity or slightly tothe left of it by shifting the supporting clamp. Theangle between clamp and square rail must notexceed 5_.If the maximum travel of the supporting clamp is notsufficient, mount the suspension strap. Protect thecable by running it through the flexible tubing and fixthe cable to the suspension strap with the cableconnectors.
When mounting the unit, lock all fastening studs ofadapter and supporting clamp with a high--strengthlocking agent (e.g. Loctite 270).
Clamp
Adapter
4KTRSquare guide rail
Clampingring
Connectingcable
Flexible tubing
Cable connector
Suspensionstrap
Supportingclamp
Dimensions table Dimension in mmSize Pitch = 0_ Pitch = 10_ Pitch = 20_ Pitch = 30_ Pitch = 40_
Hu Lu Su Tu Hu Lu Su Tu Hu Lu Su Tu Hu Lu Su Tu Hu Lu Su Tu
V2... /1 4... < 0 560 225 265 30 585 240 1.L* 120 595 250 2.L* 200 585 240 4.L* 275 560 230 6.L*V2... /2 4... < 0 560 230 260 30 585 240 1.L* 120 595 250 2.L* 200 585 240 4.L* 275 560 230 6.L*C2... /1 4... < 0 560 230 230 40 585 250 245 130 595 250 2.L* 210 590 260 3.L* 280 565 245 5.L*C2... /2 4... < 0 560 235 225 40 585 250 245 130 595 250 2.L* 210 590 260 3.L* 280 565 245 5.L*C3... /1 6... < 0 560 240 220 90 595 250 245 175 615 250 2.L* 250 615 260 3.L* 320 600 245 5.L*C3... /2 6... < 0 630 275 255 100 665 285 280 195 680 285 305 285 675 285 2.L* 365 650 270 4.L*C4... /2 8... < 0 770 330 320 115 810 335 350 225 830 355 1.L* 330 825 340 3.L* 420 795 330 5.L*C4... /4 8... < 0 770 340 310 115 810 345 340 225 830 355 1.L* 330 825 340 3.L* 420 795 330 5.L*C5 22 /4 12... 20 860 400 290 160 920 415 325 290 960 420 360 410 965 420 390
Pit hC5 23 /4 12... 50 860 400 290 185 920 415 325 310 960 420 360 425 965 420 390 Pitchmust not exceed
C6... /4 12... 90 860 400 290 225 930 415 325 350 970 420 360 460 985 420 390must not exceed
30_C6... /8 12... 90 985 460 350 245 1050 475 385 390 1085 475 420 520 1090 470 455
30_
*) see note page 36
T 0294-457712 F 0294-457713 [email protected]
Amamix� direct
40
Standard accessories 4Cranes and Lifting equipmentAmamix 215, 300, 400, 500, 600
Lifting equipment Lifting ropes Rope tensioning device / bollard
Sling point(in gravity centre position)
Shackle includedin scope of supply SEIL
PPSEIL1.4401 or
Sling pointon mixer
SP
Item No. Accessories Description
SEIL 1.4401 Lifting rope Stainless steel, diam. 5 mm, 12 m/18 m/22 m long, made of 1.4401, forcranes 4.2, 4.4, 4.6 and 4.8, make Haacon;rope is attached to the sling point on the mixer and can be fastened on thewinch of the above cranes;when transportable cranes are used, the rope remains attached to the mixerafter having been removed from the winch and is fastened to a rope tension-ing device on the tank edge
SP Rope tensioning device /bollard
For locking the lifting ropes, item No. SEIL 1.4401, of cranes (make Haacon)on the tank edge or railing
SEIL PP Lifting rope Lifting rope made of polypropylene synthetic fibres of excellent chemical re-sistance, with connecting loops at intervals of 1 m;available in fixed lengths of 5 m
FH Lifting hook For mounting on the lifting gear of the crane (lifting chain/rope) when usingtransportable cranes (e.g. if the crane used is different from the cranes sup-plied by KSB);to facilitate handling we recommend the combination of crane 4.2, 4.4, 4.6 or4.8 with the stainless steel lifting rope
FB Lifting clamp For mounting on the lifting lug
0W 384 457--00
FB
FH
Alternative:Combination: Lifting clamp (FB) (on the mixer) / Lifting hook (FH) (on the lifting rope of the crane)
250
100
� 20
T 0294-457712 F 0294-457713 [email protected]
Amamix� direct
41
Standard accessories 4Cranes and Lifting equipmentAmamix 215, 300, 400, 500, 600
Item No. Description for size Material Material No. Weight[kg]
SEIL1 4401
Lifting rope for cranes 4.2 / 4.4 / 4.6 and4 8 remains attached to the mixer;
Amamix 215 ... 600 1.44011.4401 4.8, remains attached to the mixer;
can be used for transportable cranes
�=5 mm, L=12 m 11 304 621 1.9
�=5 mm, L=18 m 11 306 713 2.7
�=5 mm, L=22 m 11 306 712 3.5
SP Rope tensioning device / bollardfor Haacon cranes 4.6 and 4.8
Amamix 215 ... 600 1.4571 19 554 260 1.5
SEIL PP Lifting ropeLoad capacity 180 kg, 5 m
Select depending on unitweight
Polypropylene 11 185 207 2.0
Lifting ropeLoad capacity 450 kg, 5 m
Polypropylene 11 190 024 5.0
For larger installation depths, several 5-metre ropes shall be used.Connection by rope loops
FH Lifting hookLoad capacity max. 500 kg
Amamix 215 ... 600 1.4301 19 219 613 2.0
FB Lifting clamp Amamix 215 1.4571 19 219 830 1.1
Amamix 300(with motor 1 6)
Amamix 300(with motor 2 6)
1.4571 19 219 831 1.3
Amamix 400
Amamix 500/600 1.4571 19 219 832 1.8
See Type series booklet “KSB Lifting Equipment” 1596.5--10 !
T 0294-457712 F 0294-457713 [email protected]
d
b
w
l
m
Amamix� direct
42
Other accessories: cable support (KH)For supporting the power cable at the lifting rope or the tank edge
Polypropylene
Hex. nutV4A
Polypropylene
Bracket
Diameter Dof power cable
Variant Diameter D Art. No. Material No.
01 17--25 mm 25 NO 20 433 11 306 562
00 10--16 mm 16 NO 20 433 11 306 561
Please refer to the power cable data given in the motor catalogue !
Carbine hook
Variant Size Loadcapacity
b d l m w Weight per100 pcs.
approx. [kg]
00 60x6 150 9 6 60 9 5 2.7
Item No. Description for size Material Material No. Weight[kg]
KH Cable support / Cable clampincl. carbine hook
for power cables 7x1.5and 8x1.5
Synthetic material / A4;carbine hook A4
19 555 522 0.15
for power cables12x1.5 and 12x2.5 ;7x4+5x1.5 and 7x6+5x1.5
19 555 523 0.20
T 0294-457712 F 0294-457713 [email protected]
Amamix� direct
43
Guide railsKSB supply or supplied by customer;For accessories 7 and 21
Square guide rail60x60x3 4 KTR
Square guide rail100x100x5
0W 384 379--00
-- Guide rails as per DIN 59411, packed in tubular foil-- Lengths >6m can be attained by adding guide rail
extensions (3 metres and 6 metres long) at the site(welding and subsequent treatment to be performedat the site in accordance with applicable regulations)
Item No. Description for size Material Material No. Weight[kg]
4 KTRGuide rail 60x60x3; length 1 5 m Amamix 215/300
1.4301 11 307 851 7.85Guide rail 60x60x3; length 1.5 m Amamix 215/300
1.4571 11 307 853 7.85
Guide rail 60x60x3; length 3 m1.4301 11 304 010 15.7
Guide rail 60x60x3; length 3 m
Amamix 215/3001.4571 11 304 011 15.7
Guide rail 60x60x3; length 6 m
Amamix 215/3001.4301 11 304 596 31.3
Guide rail 60x60x3; length 6 m1.4571 11 304 597 31.3
Guide rail 100x100x5; length 3 m1.4301 11 304 598 43.2
Guide rail 100x100x5; length 3 m
Amamix 400/500/6001.4571 11 304 599 43.2
Guide rail 100x100x5; length 6 m
Amamix 400/500/6001.4301 11 304 600 86.4
Guide rail 100x100x5; length 6 m1.4571 11 304 601 86.4
Minimum submergence and wall/floor clearance
Recommended distance from the floor, h1, and liquid level above the pump, h2, for continuous operation.
The distance from vertical walls should also correspond to distance h1. If there is more than one mixer, these must be installedat a minimum distance of Ø D from each other in consideration of the reflections of the water jet and the flow turbulence.
Minimum submergence / filling level
�DW
T
h 1h 2
�D�mm�
h1 min�m�
h2 min�m�
WT min�m�
215 0.11 0.50 0.82
300 0.15 0.80 1.25
400 0.20 0.85 1.45
500 0.25 0.90 1.65
600 0.30 1.00 1.90
With standard accessories 6 (floor mounting) for shallow tanksand ducts, the floor clearance h1 can be reduced toapprox. 50 mm (pre--condition: solid floor / concrete / steel /plastics).
T 0294-457712 F 0294-457713 [email protected]