anchors for glazing€¦ · HALFEN Anchor Channel Mullion Precast panel Mullion clip by customer HALFEN Tee-bolt & Flange Nut HALFEN Anchor channel TYPICAL ANCHOR IN THIN SLAB TYPICAL

Engineered systems that provide

on-site adjustments for faster,

easier installation of curtain wall,

punched and ribbon windows.

Anchors for

Glazing

0299

HALFENANCHORING SYSTEMS

®

2

Profiles & Part Numbers ..................................................... 2

Curtain Wall Anchor Applications ....................................... 3

Curtain Wall Anchors ...................................................... 4, 5

Curtain Wall Anchors, Corners and Jambs ........................ 6

Window Anchor Applications .............................................. 7

Window Anchors ................................................................. 8

Window Spot Anchors ........................................................ 9

Installation Methods .......................................................... 10

Fasteners - Tee Bolts ....................................................... 11

Fasteners - Lock Plates, Safety and Flat Washers .......... 12

Fasteners - Flange Nuts and Nylon Nuts ......................... 13

Project Listings ................................................................. 14

Specifications .................................................................... 15

2-7/8" (72mm)

2-1/8" (55mm)

2-1/16" (52mm)

2" (50mm)

1-9/16" (40mm)

1-5/8"(42mm)

1-5/16"(34mm)

7/8"(22mm)

1-3/16"(30mm)

These illustrations are full-size profilesof the HALFEN channels shown inthis brochure.

INDEXINDEXINDEXINDEXINDEX

ANCHORS for GLAZING

7/8"(22mm)

1-5/8" (41mm)

1-1/2" (38mm)

1-1/8" (28mm)

9/16"(15mm)

5/8"(17mm)

1-7/8"(48mm)

2815 PROFILEUsed forHT 2002HT 2506HT 2512

3817 PROFILEUsed forHT 3002HT 3506HT 3512

4122 PROFILEUsed forHZ 9002

4022 PROFILEUsed forHT 4506HT 4512HT 4512 LA

5030 PROFILEUsed forHT 5512HT 5512 LA

5234 PROFILEUsed forHT 6112



3

Mullion clipby customer

Concrete slabor spandrel beam

HALFENTee-bolt & Flange Nut

HALFENAnchor Channel

Mullion

Precastpanel


HALFENTee-bolt & Flange Nut

HALFENAnchor channel

TYPICAL ANCHOR IN THIN SLABTYPICAL ANCHOR IN THIN SLABTYPICAL ANCHOR IN THIN SLABTYPICAL ANCHOR IN THIN SLABTYPICAL ANCHOR IN THIN SLAB

TYPICAL PLANTYPICAL PLANTYPICAL PLANTYPICAL PLANTYPICAL PLAN

CURTAIN WALL ANCHORS

CURTAIN WALL TO PRECAST ANCHORCURTAIN WALL TO PRECAST ANCHORCURTAIN WALL TO PRECAST ANCHORCURTAIN WALL TO PRECAST ANCHORCURTAIN WALL TO PRECAST ANCHOR

TOP OF SLAB ANCHORTOP OF SLAB ANCHORTOP OF SLAB ANCHORTOP OF SLAB ANCHORTOP OF SLAB ANCHORTYPICAL ANCHORTYPICAL ANCHORTYPICAL ANCHORTYPICAL ANCHORTYPICAL ANCHOR

These are just someof the ways in whichHALFEN AnchorChannels have beenused to anchor curtainwalls. Other anchordetails are possible.Call for applicationassistance.

TOP OF SLAB ANCHOR WITH POCKTOP OF SLAB ANCHOR WITH POCKTOP OF SLAB ANCHOR WITH POCKTOP OF SLAB ANCHOR WITH POCKTOP OF SLAB ANCHOR WITH POCKETETETETET

HALFENTee-bolt & nut


Mullion



(25mm)

Mullion clipsby customer



Pocket formed in top of slab;fill with grout after assembly.

NOTE: Halfen cancustomize embeds tosuit larger-than-normalload conditions.




Mullion

4

ForApplicationHelp Call

1-800-323-6896

Notes: 1. Refer to pages 11, 12 and 13 for fasteners2. Stainless steel anchor channels are also available.

Consult Halfen for capacities.3. Other lengths of channel are readily available.

ANCHOR CHANNEL SELECTION CHARTANCHOR CHANNEL SELECTION CHARTANCHOR CHANNEL SELECTION CHARTANCHOR CHANNEL SELECTION CHARTANCHOR CHANNEL SELECTION CHART

Part Dimensions WeightNo. A in B in C in D in E in F in G in lb

(mm) (mm) (mm) (mm) (mm) (mm) (mm) (kg)

HT 2512 1-1/8 9/16 3/32 7/16 3 9/16 9/16 1.1(28) (15) (2.3) (12) (75) (15) (15) (0.5)

HT 3512 1-1/2 5/8 1/8 11/16 3-1/16 3/4 9/16 1.7(38) (17) (3) (18) (77) (20) (15) (0.8)

HT 4512 1-9/16 7/8 1/4 11/16 3-1/4 3/4 9/16 1.9(40) (22) (6) (18) (82) (20) (15) (0.9)

HT 4512 LA 1-9/16 7/8 1/4 11/16 5-3/4 1 3/4 2.7(40) (22) (6) (18) (147) (25) (20) (1.3)

HT 5512 2 1-3/16 5/16 7/8 3-1/2 1 9/16 2.9(50) (30) (8) (22) (90) (25) (15) (1.4)

HT 5512 LA 2 1-3/16 5/16 7/8 6-1/8 1-3/16 3/4 3.8(50) (30) (8) (22) (155) (30) (20) (1.7)

HT 6112 2-1/16 1-5/16 7/16 7/8 6-1/4 1-9/16 3/4 4.8(52) (34) (12) (22) (159) (40) (20) (2.2)

HT 6712 2-1/8 1-5/8 9/16 1-1/16 7-1/8 1-9/16 1-9/16 6.9(55) (42) (15) (20) (182) (40) (40) (3.1)

HT 7112 2-7/8 1-7/8 5/8 1-5/16 6-7/8 2 3/4 8.6(72) (48) (16) (33) (173) (50) (20) (3.9)


Nail hole each end

Center anchor deleted onHT6112, HT6712 and HT7112

D A T

C

B

EQ

EQ

E

F

G

A

B

12" (305mm)

5

Notes: 1. *These values may be increased by 1/3 for wind or seismic loads.2. All other loads are controlled by concrete strength. Stated loads are based on unreinforced

nomal weight concrete with f'c = 3,000psi (20.7 MPa). These loads may be increased for higherstrength concrete using the factor of

up to a maximum of 5,000 psi (34.5MPa).

3. Check interaction using the formula:

4. All load capacities are based on use of 2 bolts in anchor channel, with bolts spaced at 3 to 6inches (76 to 152mm) centers, and include a safety factor of 3.

5. Pull-out loads shown are worst-case off-center loads [i.e. when extreme bolt is 1" (25mm) fromend of anchor channel].

Anchor Type Concrete Thickness T in (mm)Channel of 4-1/2 5 5-1/2 6 6-1/2 7 8 9 10 12 14Part No. Load (114) (127) (140) (152) (165) (178) (203) (229) (254) (305) (356)

Pull-out lb 1,800 2,200* 2,200* 2,200* 2,200* 2,200* 2,200* 2,200* 2,200* 2,200* 2,200*HT 2512 (kN) (8.0) (9.8) (9.8) (9.8) (9.8) (9.8) (9.8) (9.8) (9.8) (9.8) (9.8)

Shear lb 1,200 1,400 1,650 1,900 1,900 1,900 1,900 1,900 1,900 1,900 1,900(kN) (5.3) (6.2) (7.3) (8.5) (8.5) (8.5) (8.5) (8.5) (8.5) (8.5) (8.5)

Pull-out lb 3,050 3,400 3,750 4,050* 4,050* 4,050* 4,050* 4,050* 4,050* 4,050* 4,050*HT 3512 (kN) (13.6) (15.1) (16.6) (18.0) (18.0) (18.0) (18.0) (18.0) (18.0) (18.0) (18.0)

Shear lb 1,750 2,150 2,500 2,900 3,300 3,750 3,750 3,750 3,750 3,750 3,750(kN) (7.8) (9.5) (11.2) (12.9) (14.7) (16.7) (16.7) (16.7) (16.7) (16.7) (16.7)

Pull-out lb 4,300 4,500 4,550 4,600 4,600 4,600 4,600 4,600 4,600 4,600 4,600HT 4512 (kN) (19.1) (19.8) (20.2) (20.5) (20.5) (20.5) (20.5) (20.5) (20.5) (20.5) (20.5)

Shear lb 1,800 2,150 2,550 2,950 3,350 3,800 4,650 4,650 4,650 4,650 4,650(kN) (8.0) (9.6) (11.3) (13.1) (14.9) (16.9) (20.7) (20.7) (20.7) (20.7) (20.7)

Pull-out lb 4,800 4,850 4,850* 4,850* 4,850* 4,850* 4,850* 4,850* 4,850* 4,850* 4,850*HT 4512 LA (kN) (21.4) (21.6) (21.6) (21.6) (21.6) (21.6) (21.6) (21.6) (21.6) (21.6) (21.6)

Shear lb 1,800 2,150 2,550 2,950 3,350 3,800 4,650 4,650 4,650 4,650 4,650(kN) (8.0) (9.6) (11.3) (13.1) (14.9) (16.9) (20.7) (20.7) (20.7) (20.7) (20.7)

Pull-out lb 4,450 4,650 4,800 4,900 4,950 5,000 5,000 5,000 5,000 5,000 5,000HT 5512 (kN) (19.8) (20.7) (21.4) (21.8) (22.0) (22.3) (22.3) (22.3) (22.3) (22.3) (22.3)

Shear lb 1,850 2,300 2,750 3,150 3,550 3,950 4,750 5,300 5,500 5,500 5,500(kN) (8.2) (10.2) (12.2) (14.0) (15.8) (17.6) (21.1) (23.6) (24.5) (24.5) (24.5)

Pull-out lb 5,050 5,400 5,700 5,950 6,150 6,350 6,700 6,700 6,700 6,700 6,700HT 5512 LA (kN) (22.2) (24.0) (25.4) (26.5) (27.4) (28.3) (29.8) (29.8) (29.8) (29.8) (29.8)

Shear lb 1,850 2,300 2,750 3,150 3,550 3,950 4,750 5,300 5,500 5,500 5,500(kN) (8.2) (10.2) (12.2) (14.0) (15.8) (17.6) (21.1) (23.6) (24.5) (24.5) (24.5)

Pull-out lb 5,800 6,300 6,750 7,200 7,600 8,000 8,650 8,850 9,200 10,000 10,000HT 6112 (kN) (25.8) (28.0) (30.0) (32.0) (33.8) (35.6) (38.5) (39.4) (40.9) (44.5) (44.5)

Shear lb 1,900 2,350 2,800 3,300 3,800 4,350 5,500 5,900 6,850 8,950 11,200(kN) (8.5) (10.5) (12.5) (14.7) (16.9) (19.4) (24.5) (26.3) (30.5) (39.8) (49.8)

Pull-out lb Not recommended 7,400 8,850 10,000 11,150 12,400 13,200HT 6712 (kN) (32.9) (39.4) (44.5) (49.6) (55.2) (58.7)

Shear lb Not recommended 2,800 3,050 3,850 4,650 6,500 8,500(kN) (12.5) (13.6) (17.1) (20.7) (28.9) (37.8)

Pull-out lb Not recommended 6,300 7,550 8,500 9,500 10,100 11,200HT 7112 (kN) (28.0) (33.5) (37.8) (42.3) (45.0) (49.8)

Shear lb Not recommended 2,100 2,300 2,900 3,500 4,900 6,400(kN) (9.3) (10.2) (12.9) (15.6) (21.8) (28.5)

Project f'cf'c = 3,000

( ) ( )+T 5/3 V 5/3 <1.0 Where: T = Actual pull-out load on anchorTA VA TA = Allowable pull-out load

V = Actual shear load on anchorVA = Allowable shear load

ALLOWABLE LOAD CHARTALLOWABLE LOAD CHARTALLOWABLE LOAD CHARTALLOWABLE LOAD CHARTALLOWABLE LOAD CHART

S� � � � � � � �

� � ��

� � � �

SHEAR LOAD

PULL-OUTLOAD


6

Corner Anchor Number of For use withPart Number I -Anchors Corresponding

on Back Anchor Channel

HT 2512 x 12 B 4 HT 2512HT 3512 x 12 B 4 HT 3512HT 4512 x 12 B 4 HT 4512HT 4512 x 12 LA B 4 HT 4512 LAHT 5512 x 12 B 4 HT 5512HT 5512 x 12 LA B 4 HT 5512 LAHT 6112 x 12 B 3 HT 6112HT 6712 x 12 B 3 HT 6712HT 7112 x 12 B 3 HT 7112

Load capacities of HALFEN corner anchors are the sameas for the corresponding HALFEN anchor channel (seepages 4 & 5). Load on channel lips at each bolt positionmust not exceed 50% of anchor channel capacity.

CORNER ANCHORSCORNER ANCHORSCORNER ANCHORSCORNER ANCHORSCORNER ANCHORS

JAMB ANCHORSJAMB ANCHORSJAMB ANCHORSJAMB ANCHORSJAMB ANCHORS


1-800-323-6896


In most cases, the anchor channels used at thejambs will be the same as those used at theintermediates. Check to ensure that the load onthe channel lips at each bolt position does notexceed 50% of the anchor channel capacity.

12"(305mm

)

Mullion clip by customersized to suit loads

Jamb Mullion



Mullion clip bycustomer sized to suit loads



HALFENCorner Anchor

Corner Mullion

12" (305mm)

7

HALFEN AnchorChannel

Shims by customer

PrecastPanel

HALFEN Tee-boltand flange nut

Track bycustomer

HALFEN ToothedTee-bolts and nuts

Bracket by others

HALFEN anchor assembly comprises twoToothed Spot Inserts with strap.(strap optional)

HALFEN Toothed Spot Insertscast into concrete allows adjustmentand prevents slippage under wind load.

Full height shimsby customer

Track and clipby customer



HALFEN Tee-bolt,washer and nylonlock nut

HALFEN safety washer


Clip and trackby customer

PUNCHED or RIBBONWINDOW ANCHORS

Precastpanel

Clip by customer


Top Track by customer

HALFEN HZ9002Toothed SpotAnchor channel

FLOATING HEAD DETAILFLOATING HEAD DETAILFLOATING HEAD DETAILFLOATING HEAD DETAILFLOATING HEAD DETAIL

FIXED SILL DETAILFIXED SILL DETAILFIXED SILL DETAILFIXED SILL DETAILFIXED SILL DETAIL


FLOATING HEAD DETAILFLOATING HEAD DETAILFLOATING HEAD DETAILFLOATING HEAD DETAILFLOATING HEAD DETAIL

FIXED SILL OR HEAD DETAILFIXED SILL OR HEAD DETAILFIXED SILL OR HEAD DETAILFIXED SILL OR HEAD DETAILFIXED SILL OR HEAD DETAIL


FIXED HEAD DETAILFIXED HEAD DETAILFIXED HEAD DETAILFIXED HEAD DETAILFIXED HEAD DETAIL


Clip and trackby customer



Track and clipby customer


HALFEN AnchorChannelor Spot Insert

8

Part Number HT 2506 HT 3506 HT 4506Number of Bolts 1 2 1 2 1 2

Allowable lb 1,200 * 2,100 * 2,200 * 2,900* 2,500 3,300Pull-out Load (kN) (5.3) (9.3) (9.8) (12.9) (11.1) (14.7)

Allowable lb 1,000 1,500 2,300 3,300 3,050 3,600Shear Load (kN) (4.4) (6.7) (10.2) (14.7) (13.6) (16.0)

A in (mm) 1-1/8 (28) 1-1/2 (38) 1-9/16 (40)

B in (mm) 9/16 (15) 5/8 (17) 7/8 (22)

Dimensions C in (mm) 3/32 (2.3) 1/8 (3) 1/4 (6)

E in (mm) 3 (75) 3-1/16 (77) 3-1/4 (82)

F in (mm) 9/16 (15) 3/4 (20) 3/4 (20)


1-800-323-6896


Notes: 1. Anchor channels are supplied with nail holes and foam filled.2. Loads marked * can be increased by 1/3 for wind loads.3. Loads shown include a safety factor of 3.4. Loads shown are in precast concrete with f'c > 5,000 psi (34.5 MPa).5. Loads shown are anywhere in the channel with extreme bolt a minimum

of 1" (25 mm) from end of channel.6. Refer to pages 11, 12 and 13 for fasteners.

SELECTION CHARTSELECTION CHARTSELECTION CHARTSELECTION CHARTSELECTION CHART

E

F

A

B

C

6" (152mm)

- +

- +WIND LOAD

WIND LOAD

DEAD LOAD

SHEAR LOAD

Pull-OutLoad

Pull-OutLoad

Clip by Customer

Clip by Customer


HEAD

SILL

Clip by Customer


HALFENTee-Bolts

6" (152mm) Long

2" (51mm)Minimum

Edge Distance2" (51mm) for HT25063" (76mm) for HT3506and HT4506

9

Slip Load

Pull-OutLoad

ShearLoad

5/16" (8mm) deep in-turned lip withteeth on HZ9002 only.

Notes: 1. Spot inserts are supplied with nail holes and are foam filled.2. Loads marked * may be increased by 1/3 for wind.3. Loads shown include a safety factor of 3.4. Loads shown are for spot inserts in precast concrete with

f'c > 5,000 psi (34.5 MPa).5. Refer to pages 11, 12 and 13 for fasteners.

Part Number HT 2002 HT 3002 HZ 9002Allowable lb 1,100 * 2,200 * 1,750 *Pull-out Load (kN) (4.9) (9.8) (7.8)

Allowable lb 1,000 2,500 2,200Shear Load (kN) (4.5) (11.1) (9.8)

Allowable lb 1,325 *Slip Load (kN) (5.9)

A in (mm) 1-1/8 (28) 1-1/2 (38) 1-5/8 (41)

Dimensions B in (mm) 9/16 (15) 5/8 (17) 7/8 (22)

E in (mm) 3 (75) 3-1/16 (77) 3-1/4 (82)

L in (mm) 1-3/4 (45) 1-3/4 (45) 2-1/4 (55)

Not Recommended

SELECTION CHARTSELECTION CHARTSELECTION CHARTSELECTION CHARTSELECTION CHART

HALFEN spot inserts provide economical nominal adjustmentfor window or door frame anchoring. They are a more practicalalternative to cast-in ferrules or drilled-in anchors. Toothed spot insertsare recommended to prevent slippage of load along the anchor.

SPOT INSERTSSPOT INSERTSSPOT INSERTSSPOT INSERTSSPOT INSERTS


HALFENSpot Inserts

3" (76mm)Minimum

Edge Distance2" (51mm) for HT20023" (76mm) for HT3002and HZ9002

Precast Head orSill Panel

3" (76mm)Minimum

3" (76mm)Minimum

HALFEN ToothedSpot Insert

Precast Sill orHead Panel

Wind Load

B

L

EA

10


1-800-323-6896

For wooden forms, simply locate the HALFENAnchor Channel in the correct position, then nailthrough the pre-punched holes in the back of thechannel into the form.

For steel forms: (sometimes used for precastpanels), pre-drill two small holes through form, locatethe anchor channel then secure using 2 self-drillingscrews (TEKS or similar) from the outside. Removethe screws before stripping the form.

INSTALLATIONINSTALLATIONINSTALLATIONINSTALLATIONINSTALLATION

ANCHORS for GLAZING

For metal pour-stops, pre-punch a slot1/2" (12 mm) shorter than the lengthof the anchor channel, and the samewidth as the slot in the face of theHALFEN Anchor Channel.

Position the Anchor Channel over theslot in the pour-stop. Tack weld 2 or 3places along top edge and once at eachend as shown.

11

For use with HT 2002, HT 2506 HT 3002, HT 3506 HT 4506, HT 4512HT 2512 HT 3512 HT 4512 LA

Bolt M10 M10 M12 M16 M12 M16Diameter (3/8") (3/8") (1/2") (5/8") (1/2") (5/8")

Strength 4.8 8.8 4.6 4.6 4.6 4.6 8.8 4.6 8.8Grade Std Hi Tensile Std Std Std Std Hi Tens Std Hi Tens

Nut lb. ft. 11 36 11 19 45 19 55 45 147Torque (N.m) (15) (48) (15) (25) (60) (25) (75) (60) (200)

Allowable lb 1,700 3,550 1,700 2,500 4,650 2,500 5,200 4,650 9,650Tension Load (kN) (7.6) (15.8) (7.6) (11.1) (20.7) (11.1) (23.1) (20.7) (42.9)

Allowable lb 1,150 2,350 1,150 1,650 3,100 1,670 3,450 3,100 6,450Shear Load (kN) (5.1) (10.5) (5.1) (7.3) (13.8) (7.4) (15.4) (13.8) (28.5)

Lengths mm (in) Tee-Bolt & Nut Part Number

30 (1-1/4) BD2312 X BD3311 BD3412 BD3512 BD4412 X BD4511 X

40 (1-1/2) BF2311 BF2322 BF3311 BF3411 BF3511 BF4411 X BF4511 BF4521

45 (1-3/4) X X X X X X BG4421 X X

50 (2) BH2312 X BH3311 BH3412 BH3512 BH4412 X BH4512 X

60 (2-3/8) BJ2311 X X BJ3411 BJ3511 BJ4411 BJ4421 BJ4511 BJ4521

TEE-BOLT SELECTION CHARTTEE-BOLT SELECTION CHARTTEE-BOLT SELECTION CHARTTEE-BOLT SELECTION CHARTTEE-BOLT SELECTION CHART

Tee-bolts canbe insertedanywhere alongthe channel andturned 90° tolock intoposition.

FASTENERS

For use with HT 5512, HT5512 LA, HT 6112, HT 6712 HT 7112 HZ 9002

Bolt M12 M16 M20 M24 M12Diameter (1/2") (5/8") (3/4") (1") (1/2")

Strength 4.6 8.8 4.6 8.8 4.6 8.8 4.6 8.8 8.8Grade Std Hi Tensile Std Hi Tens Std Hi Tens Std Hi Tens Hi Tens

Nut lb. ft. 19 55 45 147 88 295 147 500 55Torque (N.m) (25) (75) (60) (200) (120) (400) (200) (680) (75)

Allowable lb 2,500 5,200 4,650 9,650 7,250 15,050 10,450 21,700 5,200Tension Load (kN) (11.1) (23.1) (20.7) (42.9) (32.3) (67.0) (46.5) (96.6) (23.1)

Allowable lb 1,650 3,450 3,100 6,430 4,850 10,050 6,950 14,450 3,450Shear Load (kN) (7.3) (15.4) (13.8) (28.6) (21.5) (44.4) (30.9) (64.3) (15.4)

Lengths mm (in) Tee-Bolt & Nut Part Number

30 (1-1/4) BD5411 X BD5511 X X X X X X

35 (1-3/8) X X X X BE5611 X X X BE9422

40 (1-1/2) BF5411 X BF5511 X X X X X X

45 (1-3/4) X BG5421 X X BG5611 BG5621 X X X

50 (2) BH5411 X BH5512 X X X BH7712 X BH9422

55 (2-1/4) X X X X BI5612 X X X X

60 (2-3/8) BJ5411 BJ5421 BJ5511 BJ5521 x BJ5621 X X X

75 (3) x x x x BM5611 x BM7712 BM7722 X

TEE-BOLT SELECTION CHARTTEE-BOLT SELECTION CHARTTEE-BOLT SELECTION CHARTTEE-BOLT SELECTION CHARTTEE-BOLT SELECTION CHART

Notes: 1. Part numbers ending in 1 are electroplated.2. Part numbers ending in 2 are hot dip galvanized.3. X indicates not available.4. Bolt capacity may be limited by load capacity of anchor channel.5. Stainless steel tee-bolts and nuts are also available.6. Bolt length shown in table is length from underside of head to end of shank. To determine projection from face

of concrete, deduct lip thickness of selected channel.

12

Locking plates are an alternative to tee-bolts. They are recommendedfor situations where clearance problems preclude the use of tee-bolts.Locking plates can be inserted anywhere along the length of the channeland turned 90° to lock into position.

HT 2002 HT 3002For use with HT 2506 HT 3506

HT 2512 HT 3512

Suits bolt size M10 (3/8") M10 (3/8") &M12 (1/2")

Part Number SW2815M10 SW3817M12

T in (mm) 1/16 (1.5) 3/32 (2)

Dimensions W in (mm) 1 (25) 1-3/8 (35)

X in (mm) 7/16 (12) 9/16 (14)Note: 1. Only available electroplated.

2. Safety washers are only required on 2815 and 3817series channels when the tee-bolt is left loose to allowmovement. They prevent the tee-bolt from rotating outof the channel after installation.

LOCKING PLATESLOCKING PLATESLOCKING PLATESLOCKING PLATESLOCKING PLATES

Type Flat Washers Large Flat Washers

Size M10 M12 M16 M20 M24 M10 M12 M16 M20

Part Number HW1011 HW1211 HW1611 HW2011 HW2411 HW1011L HW1211L HW1611L HW2011L

D in (mm) 13/16 (21) 15/16 (24) 1-1/4 (30) 1-7/8 (37) 1-3/4 (44) 1-1/4 (30) 1-1/2 (40) 2 (50) 2-5/8 (68)

Dimensions d in (mm) 7/16 (11) 1/2 (13) 5/8 (17) 13/16 (21) 1 (25) 7/16 (11) 1/2 (13) 5/8 (17) 7/8 (22)

T in (mm) 1/16 (2) 3/32 (2.5) 1/8 (3) 1/8 (3) 5/32 (4) 3/32 (2.5) 1/8 (3) 1/8 (3) 3/16 (5)

WASHERSWASHERSWASHERSWASHERSWASHERS

Note: 1. Part Numbers shown are for electroplated.2. Hot dip galvanized finish also available. Part numbers will end in 2 instead of 1 (e.g. HW1012, HW1612, etc).3. Large flat washers are recommended when securing clips with slots.

For use with HT 2002 HT 3002 HZ 9002

Locking Plate 1/4" 5/16" 3/8" 1/2" 3/8" 1/2" 5/8"Size UNC UNC UNC UNC UNC UNC UNC

Bolt ft. lb. 2 6 11 19 19 50 100Torque (N.m) (2.7) (8) (15) (25) (25) (68) (136)

Allowable lb 400 600 1,200 1,200 1,850 2,000 2,350Tension Load (kN) (1.8) (2.7) (5.3) (5.3) (8.2) (8.9) (10.5)

Allowable lb 400 600 1,200 1,200 1,100 2,000 2,200Shear Load (kN) (1.8) (2.7) (5.3) (5.3) (4.9) (8.9) (9.8)

Allowable lb 100 140 260 370 750 1,500 2,250Slip Load (kN) (0.4) (0.6) (1.2) (1.6) (3.4) (6.7) (10.0)

Part Number LP2111 LP2211 LP3311 LP3411 LP9311S LP9411S LP9511SS

LOCKING PLATE SELECTION CHARTLOCKING PLATE SELECTION CHARTLOCKING PLATE SELECTION CHARTLOCKING PLATE SELECTION CHARTLOCKING PLATE SELECTION CHART

FASTENERS

Not Recommended

SAFETY WASHERSSAFETY WASHERSSAFETY WASHERSSAFETY WASHERSSAFETY WASHERS

Note: 1. Only available zinc electroplated.

D

d

T

W

X

T

W

Tabs on Safety Washersprevent Bolt Headfrom Rotating

HALFENSafety Washer

13

Nut Size M10 M12 M16

Nut Torque ft. lb. 36 61 144(N.m) (49) (83) (195)

Allowable Slip Load lb 550 550 1,900on T5 Aluminum (kN) (2.5) (2.5) (8.5)

Allowable Slip Load lb 550 860 1,150on Steel (kN) (2.5) (3.8) (5.1)

Part Number HN1011TEN HN1211TEN HN1611TEN

F mm (in) 15 (9/16) 17 (5/8) 22 (7/8)

Dimensions D mm (in) 21 (13/16) 24 (15/16) 31 (1-1/4)

H mm (in) 8 (5/16) 9 (3/8) 11 (7/16)

Note: 1. Only available electroplated.2. Should only be used with HALFEN Grade 8.8 (High Tensile) tee-bolts

to resist loads shown above.3. Flange nuts may be used with HALFEN standard grade 4.6 tee-bolts but are not

recommended to resist slip. They should not be torqued any higher then the torqueof the applicable standard grade tee-bolt.

Note: 1. Only available electroplated.

Size M10 M12 M16 M20

Part Number HN1011NY HN1211NY HN1611NY HN2011NY

F mm (in) 17 (5/8) 19 (3/4) 24 (15/16) 30 (1-3/16)

Dimensions C mm (in) 19 (3/4) 21 (13/16) 26 (1-1/16) 33 (1-5/16)H mm (in) 10 (3/8) 13 (1/2) 16 (5/8) 21 (13/16)

FASTENERS

FLANGE NUTSFLANGE NUTSFLANGE NUTSFLANGE NUTSFLANGE NUTS

NYLON LOCK NUTSNYLON LOCK NUTSNYLON LOCK NUTSNYLON LOCK NUTSNYLON LOCK NUTS

Nylon lock nuts may be used instead of the regular hexagon nuts providedwith Tee-bolts. They are self-locking and can be used where floatingconnections are required, or where positive locking of the nut is required.

Flange nuts are flanged hexagon nuts with teeth on the flange face.Flange nuts may be used instead of the regular hexagon nuts providedwith Tee-bolts, to prevent slotted clips from slipping under load.

14

HALFEN Anchor Channels have been used on hundreds of projectsworld-wide to anchor facade glazing systems. These projects are apartial listing.

• Le Grande Palais, • Bellevue Pacific Tower,New York, NY Belleview, WA

• Fulton County Courthouse, • Federal Center,Atlanta, GA Atlanta, GA

• Eight Greenspoint Plaza • Waikiki LandmarkHouston, TX Honolulu, HI

• First Bank, • M D Anderson,Minneapolis, MN Houston, TX

• First Interstate Tower, • Federal Archives,Los Angeles, CA College Park, MD

• Foley Square Courthouse, • V A Medical CenterNew York, NY New Orleans, LA

• Commerce Square, • Baptist Medical CenterPhiladelphia, PA Nashville, TN

• Chicago Title & Trust, • Metrotech,Chicago, IL Brooklyn, NY

• Oceana II, • Glaxo,Miami, FL Research Park Triangle, NC

• Amsouth, • BMI Center,Birmingham, AL Nashville, TN

• Harbor Court, • Criminal Justice Center,Honolulu, HI Philadelphia, PA

• County Courthouse • USG BuildingPrince Georges Co., MD Chicago, IL

• Brigham & Women's Hospital • United CenterBoston, MA Chicago, IL

• Federal Courthouse • Plaza TowerGreenbelt, MD Costa Mesa, CA

• California AttorneyGeneral's OfficeSacramento, CA

CURTAIN WALL PROJECTSCURTAIN WALL PROJECTSCURTAIN WALL PROJECTSCURTAIN WALL PROJECTSCURTAIN WALL PROJECTS

• United Parcel Service, • Nike HeadquartersAtlanta, GA Beaverton, OR

• 101 Hudson • La RivageJersey City, NJ Naples, FL

• Hoxworth Center, • Two Pierce PlaceCincinnatti , OH Itasca, IL

• Gateway Arena • 255 5th St.Cleveland, OH Cincinnatti , OH

• Venetian Tower • State University of New YorkNaples, FL Buffalo, NY

• Bell South • Children's HospitalCharlotte, NC Columbus, OH

RIBBON OR PUNCHED WINDOW PROJECTSRIBBON OR PUNCHED WINDOW PROJECTSRIBBON OR PUNCHED WINDOW PROJECTSRIBBON OR PUNCHED WINDOW PROJECTSRIBBON OR PUNCHED WINDOW PROJECTS

ANCHORS for GLAZING

PROJECTSPROJECTSPROJECTSPROJECTSPROJECTS

15

ANCHORS for GLAZING

Please consult the HALFEN Anchoring Systemscatalog or call HALFEN for information on the fullrange of anchoring devices available.

Halfen products

meet a wide range

of applications...

..or can be

custom designed

to fit YO U R needs.

Curtain wall (Glazing system) to be anchored to cast-in-place concrete (concrete floor slabs) (precastconcrete) with HALFEN Anchoring Systems anchor channels manufactured by Meadow BurkeProducts, Converse, TX, phone (800) 323-6896, (210) 658-4671 • FAX (888) 277-1695, (210)658-7908.

Anchor channels and fasteners shall be selected to adequately accommodate the loads applied bythe glazing system, and to provide liberal adjustability during erection. Anchor channels to be hotdip galvanized and foam filled to prevent wet concrete seepage into channel cavity. Fasteners tobe zinc electroplated (hot dip galvanized) (stainless steel) and shall be supplied by the anchorchannel manufacturer.

SAMPLE SPECIFICATIONSSAMPLE SPECIFICATIONSSAMPLE SPECIFICATIONSSAMPLE SPECIFICATIONSSAMPLE SPECIFICATIONS

MATERIAL SPECIFICATIONSMATERIAL SPECIFICATIONSMATERIAL SPECIFICATIONSMATERIAL SPECIFICATIONSMATERIAL SPECIFICATIONS

Yield UltimateComponent Specification Strength Strength

psi (MPa) psi (MPa)

Cold Formed Channels ASTM A570 Gr33 34,000 (235) 52,200 (360)

Hot Rolled Channels & I-Anchors ASTM A283 Gr D 34,000 (235) 52,200 (360)

Hot Rolled Channel Type 5542 ASTM 570 Gr 40 39,900 (275) 62,300 (430)

Standard Grade Tee-bolts ASTM F568 Gr4.6 34,800 (240) 58,000 (400)

High Tensile Tee-bolts ASTM F568 Gr8.8 95,700 (660) 120,300 (830)

Locking Plates ASTM A283 Gr D 34,000 (235) 52,200 (360)

Hot Dip Galvanizing ASTM A123, A153

Zinc Electroplating ASTM B633

HALFEN Anchor Channels and accessories meet or exceed these specifications.

HAFLEN Anchoring Systems reserves the right to change specifications or products at any time.

ANCHORS for GLAZING

Flexibility of design

Ease of installation

Unsurpassed strength

Variety of sizes

Pre-engineered

Durable

Competitive cost

Performance proven

Application assistance

Technical support

With two or three dimensional adjustment

capabilities and versatility of application, HALFEN

systems make almost any design possible.

Because they are so easy to install and work with,

HALFEN systems save time and labor costs.

HALFEN anchor channels are the strongest on the

market, with allowable loads up to 17,600 Ibs.

HALFEN anchor channels are manufactured from 11

different channel profiles, in lengths from 1-3/4

inches to 20 feet.

Off the shelf components.

Hot dip galvanized finish is standard for anchor

channels. Stainless steel components are also

readily available.

At the front end, HALFEN is highly competitive with

other anchoring systems.

Thousands of projects world-wide, over 65 years of

experience.

HALFEN thrives on problem solving. We regularly

work with curtain wallers, architects, engineers and

contractors to develop practical solutions to complex

design challenges.

Readily available to provide engineering assistance

and anchorage calculations.

10

9

8

6

5

4

3

2

1

7


®

No large openings inchannel backeliminates potential risk of concrete seepage through back of channel.

Robust hot rolled anchors

Low profile channel toavoid conflict withreinforcement

Nail hole each endfor securing to form work

Foam filled. Supplied as standardfor whole length of channel,providing effective barrier to concrete seepage, while being easy to remove prior toinserting bolts or restraint straps.

Tee-bolts can be inserted anywhere along thechannel and turned 90° to lock into position.

Other literature available from


®

MEADOW BURKE PRODUCTS

P. O. Box 547

Converse, TX 78109

TEL 1-800-323-6896 • 210-658-4671

FAX 1-888-277-1695 • 210-658-7908Copyright © 1999 Halfen


®

Documents

anchors for glazing€¦ · HALFEN Anchor Channel Mullion Precast panel Mullion clip by customer HALFEN Tee-bolt & Flange Nut HALFEN Anchor channel TYPICAL ANCHOR IN THIN SLAB TYPICAL