Installation Leaflet - AnyBus-PCI AS-Interface MasterRev 1.03

Web: www.anybus.com HMS Industrial Networks AB

AnyBus-PCI AS-Interface MasterPackage ContentsThe AnyBus-PCI AS-Interface Master package consists of the following items:

Anybus-PCI AS-Interface Master cardFerrite clip (Required for EMC compliance)This installation leafletCD-ROM containing software drivers, SDK and documentation

PCI Card Overview

Status LED:s

Warning!The AnyBus-PCI AS-Interface Master card contains ESD (Electrostatic Discharge) sensitive components. Be sure to observe ESD precautions when installing the card; do not touch any circuits or connectors, and handle the card only by its edges.

# Indication State Meaning1 Active Off PCI card not active

Green PCI card active (i.e. Transport Path open)2 Application Led - Controlled by software (ABS_SetApplicationLed())3 Running/Idle Green Module is in running mode

Red Module is in idle mode4 Auto prog, slave 0 exist Off No error, no slave 0, autoprogramming not possible

8Hz Green Auto programming possible1Hz Green Slave address 0 existRed Periphery error8Hz Red Periphery error, auto-programming possible1Hz Red Periphery error, slave address 0 exist

5 Network Status Off No power or not initialisedFlashing Green On line according to configurationGreen On line, but no connections establishedRed Offline

6 Module Status Off No power or not initialisedFlashing Green Protected modeGreen Configuration modeRed Power Fail bus

PCI Edge Connector

Status LED:s

AS-Interface

Config Connector

135

246

Installation Leaflet - AnyBus-PCI AS-Interface MasterRev 1.03

HMS Industrial Networks AB Web: www.anybus.com

Software Driver Installation

1. Double click on ‘Setup.exe’.(This file will be executed automat-ically when inserting the supplied software CD-ROM provided that the AutoPlay feature is enabled.)

2. Click ‘Browse’ to select a different installation path, or click ‘Next’ to start the installation process.

3. A progress bar will illustrateprogress of the installation.

4. Finished.Shut down the computer and pro-ceed with the hardware installation steps described on the following pages.

Important:• It is strongly recommended to perform the software installation prior to installing the PCI card into the PC. This

ensures that the software drivers are available when the card is detected by the system.• Administration rights are required when installing the drivers on windows NT, 2000 or XP.• To avoid software conflicts, make sure that no other AnyBus-PCI drivers are installed in the system (e.g. the

CoDeSys drivers)!

Installation Leaflet - AnyBus-PCI AS-Interface MasterRev 1.03

Web: www.anybus.com HMS Industrial Networks AB

Hardware Installation

1. Unplug AC power and remove system cover

2. If present, remove the bracket opposite the PCI slot. Keep the screw for later use.

3. Align the card connector with the slot and press firmly until the card is completely seated

4. Secure the card connector to the chassis using the screw removed earlier

5. Re-attach the system cover and AC power

6. On the AS-Interface bus cable, attach the included ferrite clip according to this figure:

Warning!Unplug the AC power when adding or removing expansion cards or other system components. Failure to observe this may result in physical injury or damage to computer components.

Important:To ensure trouble-free operation, the front plate of the card must be screwed together with the system cover. The system cover must also be grounded in compliance with local regulations.!

Installation Leaflet - AnyBus-PCI AS-Interface MasterRev 1.03

HMS Industrial Networks AB Web: www.anybus.com

Technical Specification

Support

General• Half length 33Mhz PCI card• 3.3 & 5V support (Universal keyed add-in)• Plug & Play• Interrupt or Polled operation• 0 to +55C operating temperature

System Requirements• Windows NT 4.0 SP3 or higher or

above,Windows 98, Windows 2000, Win-dows ME, or Windows XP

• 486 DX 66 or higher recommended• 16 MB RAM (32 MB recommended)• 256-color SVGA (800x600) display• CD-ROM drive• Available PCI-slot• Mouse or tablet

Software Drivers• Supports the AnyBus-S API

(SDK included)• Multiple AnyBus PCI cards supported

AS-Interface Details• AS-Interface v2.1 compliant• Galvanically isolated bus interface• Intelligent auto configuration support• Manages up to 62 slaves• Up to 124 (16 bit) analog values• Up to 248 digital outputs/186 digital inputs• Supports extended master profiles

EMC Compliance• Emission: EN50295:1999• Immunity: EN50295:1999• CE marked

HMS SwedenEmail: support@hms-networks.comPhone: +46 (0) 35 - 17 29 20Fax: +46 (0) 35 - 17 29 09Online: www.anybus.com

HMS AmericaEmail: us-support@hms-networks.comPhone: +1-773-404-2271Fax: +1-773-404-1797Online: www.anybus.com

HMS GermanyEmail: ge-support@hms-networks.comPhone: +49-721-96472-0Fax: +49-721-964-7210Online: www.anybus.com

HMS JapanEmail: jp-support@hms-networks.comPhone: +81-45-478-5340Fax: +81-45-476-0315Online: www.anybus.com

AS-InterfaceTechnical questions regarding the AS-Interface networking system should be addressed to your local AS-Interface User Organization.

Online: www.as-interface.com

DownloadsManuals, software drivers etc., are availablefor download at ‘www.hms-networks.com’