Application Connectors for LiDAR

PowerPoint Ap p l i c a t i o n Connectors for LiDAR
1 Applications 2 Internal Connector (BtoB, FPC/FFC) 3 Interface Connector
A p p l i c a t i o n
MKT-R-20017E Issued: Nov. 2, 2020 © 2020 HIROSE ELECTRIC CO., LTD. All rights reserved. Specifications herein are subject to change without notice. Contact Hirose for the latest specifications, drawings, and availabilities. 2
Application Examples
FPC/FFC Connector -FH63S -FH67 -FH69* -FH75 -FH52K -FH65
Interface Connector -GT25 -ZE05 Interface Connector High Frequency Coaxial -GT43
MKT-R-20017E Issued: Nov. 2, 2020 © 2020 HIROSE ELECTRIC CO., LTD. All rights reserved. Specifications herein are subject to change without notice. Contact Hirose for the latest specifications, drawings, and availabilities. 3
*Under Development
()
-55 to 105 -55 to 125 -55 to 125 -55 to 125
Features With Power Contact, Floating Structure
Low Profile, Narrow Pitch
F L Y E R
MKT-R-20017E Issued: Nov. 2, 2020 © 2020 HIROSE ELECTRIC CO., LTD. All rights reserved. Specifications herein are subject to change without notice. Contact Hirose for the latest specifications, drawings, and availabilities.
Wide Floating Range
0.5mm Pitch / Supports up to 8Gbps
1 Floating range: ±0.6mm in X and Y directions
2 High speed transmission capability (Supports up to 8Gbps)
3 Power contacts on each side of the connector (3A/pin×4 lines)
4 Supports 105 to meet automotive specs.
5 ±1.2mm self-alignment capabilities
Rated Current Signal terminal0.5A Power terminal3A
Rated Voltage 50V AC
Withstanding Voltage 150V AC for 1 min.
Contact Resistance Signal terminal70mΩ Max. Power terminal30mΩ Max.
Mating Durability 100 times
0.6mm
ImageFX23
- Pos.20, 40, 60, 80, 100, 120pos. + 4pos. for power contact
- Supports RoHS *Includes temperature rise by current flow.
F L Y E R
125 Heat Resistance, Board to FPC Connector for Automotive
0.4mm Pitch/1.5-4mm Stacking Height
2 0.4mm pitch, 3.38mm depth, small FPC to board connector
3 Wide position and height varieties
4 PCI Express 4.0 (16Gbps) compliant
5 Optimized contact design and material for
high heat resistance
Withstanding Voltage
Insulation Resistance
automotive camera
Receptacle: DF40TC(3.5)-30DS-0.4V
spring design
Initial After test
AVG 18.67 20.82
Initial After test
AVG 17.67 17.30
Header: DF40TC-30DP-0.4V
[mΩ] [mΩ]
F L Y E R
DF40GT Series 125 Heat Resistant, Supports Automotive Specifications, Shielded FPC-to-Board Connector
0.4mm Pitch / 1.5mm Stacking Height
Features
Withstand Voltage 100V AC for 1 min.
Insulation Resistance 50MΩ Max. (100V DC)
125 Heat Resistant Contact Excellent EMI Protection
and Reliable Ground Design
Improve stress relaxation property
Existing product (DF40)
Initial After test
AVG 18.67 20.82
Initial After test
AVG 17.67 17.30
[mΩ] [mΩ]
No. of pos. Mass production: 10pos. Under development: 30 and 48pos.
*Includes the temperature rise by current flow.
1 125 heat resistant for automotive specifications -Contact design and materials for high heat resistance
2 Shield and grounding provide superior EMI protection
3 3.68mm depth space-saving design
4 Satisfies PCI Express 4.0 (16Gbps) requirements
Under Development
Rated Current 0.3A
Withstanding Voltage
2 Excellent EMI prevention with shielding and grounding design
3 Positive lock design due to blade lock system
4 Supports PCI Express 4.0 (16Gbps) transmission
5 Secure mating with clear tactile click
6 Contact design and material optimized for high heat resistance
Features
Component Material Finish/Remarks
Shielding Phosphor Bronze
Header
Receptacle
-No. of Pos.: 44pos.
900ppm maximum chlorine, 900ppm maximum bromine,
and 1500ppm maximum total of chlorine and bromine.

Series
Pitch (mm)
Stacking Height (mm)
Operating Temperature
()
-55 to 125 -55 to 125 -40 to 125 -40 to 125 -40 to 125 -40 to 125
Features
contact, Back Flip
F L Y E R
FH63S Series
FPC/FFC Insertion
Patented
*The lock lever close automatically when the FPC is removed, but this is not a defect of the product.
For Automotive Applications
V-by-One HS
One Action Lock, Horizontal Type FPC, FFC, Shielded FFC Connectors
0.5mm Pitch
1 One Action Lock improves workability and is ideal for robot assembly
2 Independent spring with two-point contact design for high contact reliability - Wiping effect reduces contact failure due to foreign matter
3 125 heat resistance - Passed various strict tests for automotive
4 Easy FPC insertion and high retention force
5 Shielded FFC is available for EMI prevention
Features
Operating Temperature
*This product satisfies halogen free requirements defined as 900ppm maximum chlorine, 900ppm maximum bromine,
and 1500ppm maximum total of chlorine and bromine.
- RoHS compliant, Halogen free*
Insert FPC LockInserting Click
FPC/FFC Removal Unlock Removal FPC Lock lever stays open without being hold back by hand.
Close the lock lever
Lift lock lever
F L Y E R
One Action Lock
0.5mm Pitch / 5.2mm Height
Specifications
1 High operability with a one action lock suitable for robot assembly
2 High reliability with independent two-point spring contact design. Wiping design reduces contact failure due to dust intrusion.
3 125ºC heat resistance connector to satisfy severe automotive requirements
4 Excellent FPC/FFC insertion operability and high retention force
5 Shielded FFC prevents EMI
Features
[FFC] Initial :80mΩ Max.
Insulation Resistance 500MΩ Min. (100V DC)
Withstanding Voltage 150V AC for 1min.
Operating Temperature 55 to125ºC(Only for FPC)
- Reflow Temperature: 250 Max.
- Variations: 30pos. (Under development: 10, 20, 40pos.) - RoHS, Halogen-free* product
*This product satisfies halogen free requirements defined as 900ppm maximum chlorine, 900 ppm maximum bromine, and 1500ppm maximum total of chlorine and bromine.
FPC/FFC Insertion FPC/FFC Removal
Locked Close the lock lever*
*The lock lever close automatically when the FPC is removed, but this is not a defect of the product.
Unlock Removal FPC
Lock lever stays open without being hold back by hand.
Lift lock lever
Under Development
Prevent contact failure
Specifications
Two-points contact for each top and bottom contact Backflip FPC / FFC Connector
2 Stronger FPC retention force vertically by
Backflip structure
( Can use FH28 / FH52 Series FPC )
4 FPC insertion status is visible
( Also actuator rocked condition )
5 125 heat resistant
Features
Also can use FH28 , FH52E/FH52K/FH75 land pattern . Please contact Hirose for details .
2-points contact For Top & Bottom
First In the world
Only two-steps operation Flexible FPC mating direction
Rated Current 0.5A
Contact Resistance 100mΩ (Measured under 20mV AC, 1KHz, 1mA
Withstanding Voltage 150V AC for 1 minute
Insulation Resistance 500MΩ Min (100V DC)
Mechanical Operation 10 times
Top contact
Bottom contact
F L Y E R
FH75 Series
Contact Resistance 50mΩ Max. *Includes FPC/FFC conductor
resistance (L=8mm)
0.5mm Pitch / 2mm Height
Supports MIPI D-PHY (1.5Gbps)
FPC Tab Detection
improves contact reliability.
8, 10, 15, 30, 50, 60, 68, 80pos. (Under Planning)
* This product satisfies halogen free requirements defined as 900ppm maximum chlorine, 900ppm maximum bromine, and 1500ppm maximum total of chlorine and bromine.
Features
1 Independent two-point contact design reduces contact failure due to dust intrusion.
2 125ºC heat resistance to satisfy severe automotive requirements
3 High FPC retention force with FPC tab and housing side catches
4 PCB and FPC/FFC compatible with FH52E/K/T
F L Y E R
125 Heat Resistant, Robust FPC/FFC Connector
0.5mm and 1mm Pitch / 2mm Height
Features
1 125 heat resistant connector to satisfy sever automotive requirements
2 Robust lock design with unique contact design
3 Increased FPC/FFC retention force with tabs
4 Easy visual inspection and enhanced PCB retention force by L-shaped solder tabs
5 Board area under the connector is available for PCB patterning
6 Compliant to Pick & Place mounting
Rated Current*1 0.5A
Rated Voltage 50V AC/DC
Operating Temperature -40 to +125
*1 When passing the current through all the contacts, use 70% of the rated current.
*2 FPC/FFC conductor resistance is included.
- RoHS compliant, Halogen free* *This product satisfies halogen free requirements defined as 900 ppm
maximum chlorine, 900 ppm maximum bromine, and 1500 ppm maximum total of chlorine and bromine.
- Varieties (0.5mm pitch) Under mass production: 6, 8, 10, 12, 15, 18, 20, 24, 30, 32, 34,
40, 45, 50, 68pos. Under planning : 22, 25, 26, 60, 64pos.
- Varieties (1mm pitch) Under mass production: 10pos. , Under planning: 6pos.
Series FH52 FH52E FH52K FH52T
Pitch 0.5, 1mm 0.5mm
Contact Design
Single-point Two-point
Solder Tabs
FPC/FFC Layout
F L Y E R
1 Low profile, space saving design
2 125 heat resistant connector to satisfy severe automotive
requirements
5 Space saving I-shape solder tabs allow for visual inspection
6 Board area under the connector is available for PCB patterning
Features
Insulation Resistance 500MΩ Min.100V DC
SpecificationsSpace-Saving, Low Profile Design
- Variation Mass Production: 8, 10, 15, 34pos. Technically feasible positions: 6-68pos.
(Available upon request. Please contact our sales representative for details. )
125 Heat Resistant, Low Profile Space Saving FPC/FFC Connector
FH65 Series
1 .2
m m
2 m
Height
2mm
Approx. 40% Reduction
Interface Connector
3(Full positions) 2(Full positions)
No. of Pos. 8, 12, 16, 20, 24, 32, 40 2, 4, 5, 8, 12, 16, 20,
24
Cable Size 0.08-0.5sq 0.3-0.5sq
Terminal
F L Y E R
Dimensions & Variations
Terminal tab size 0.64mm / 2.2mm pitch
2 Wide pos. varieties (8, 12, 16, 20, 24, 32, 40)
3 Strong prying force : 98N Min.
4 105 heat resistance
5 Clear tactile click
Features
Straight Type Solder tabDIP
16.35 36.9
*Includes the temperature rise by current flow.
Rated Current 3A
-No. of Pos.: 8, 12, 16, 20, 24, 32, 40 -Applicable wire: 0.12 to 0.5SQ (Outer dia. 0.8 to 1.7mm)
F L Y E R
Dimensions
2 High heat resistance 125
3 High vibration resistance
4 Rated current 5A (Mono-pole power supply) / 2A (All-poles power supply)
5 Secure tensile strength of 40N with retainer
6 Wide pos. varieties (2, 4, 5, 8, 12, 16, 20, 24)
Features
Contact Resistance 10mΩ Max.
Insulation Resistance 100MΩ Min. (DC 500V)
0.5 Size, Wire-to-Board Connector
-No. of pos.: 2, 4, 5, 8, 12, 16, 20, 24 -Applicable wire: 0.3 to 0.5SQ (Outer dia. 1.6mm[AESSX etc.)
F L Y E R
Dimensionsmm
GT43 Series
3 6 keying varieties
4 One-step crimp termination
5 High frequency transmission3GHz If not used for video transmission, consider using GT21 / GT36S.
Features
7.7
Supports LVDS, Shielded Coaxial Connector
Noise Resistance
GT43-1S-HU GT43-1P-H
Noise drops to GND plate and other side of the boards in a
different flow

Documents

Application Connectors for LiDAR