SECTION 07 14 00FLUID APPLIED WATERPROOFING

Display hidden notes to specifier. (Don't know how? Click Here)

Copyright 2010 - 2010 ARCAT, Inc. - All rights reserved

1 GENERAL

1.1 SECTION INCLUDES

1.1.1 Residential fluid applied waterproofing.

1.1.2 Commercial fluid applied waterproofing.

1.1.3 Air/vapor barrier wall assembly.

1.2 RELATED SECTIONS

1.2.1 Section 03 30 00 - Cast-in-Place Concrete.

1.2.2 Section 31 20 00 - Earth Moving.

1.2.3 Section 33 46 19.13 - Underslab Drainage Piping.

1.2.4 Section 04 22 23.29 - Split-Face Concrete Unit Masonry.

1.2.5 Section 33 46 19.13 - Underslab Drainage Piping.

1.2.6 Section 07 60 00 - Flashing and Sheet Metal.

1.3 REFERENCES

1.3.1 American Society for Testing and Materials International (ASTM):1.3.1.1 ASTM C 719 - Standard Test Method for Adhesion and Cohesion of Elastomeric

Joint Sealants Under Cyclic Movement (Hockman Cycle).1.3.1.2 ASTM C 836 - Standard Specification for High Solids Content, Cold Liquid-

Applied Elastomeric Waterproofing Membrane for Use with Separate Wearing Course.

1.3.1.3 ASTM C 898 - Standard Guide for Use of High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane With Separate Wearing Course.

1.3.1.4 ASTM D 412 - Standard Test Method for Vulcanized Rubber and Thermoplastic Elastomers-Tension.

1.3.1.5 ASTM D 466 - Standard Test Method for Films Deposited from Bituminous Emulsions.

1.3.1.6 ASTM D 2196 - Standard Test Method for Rheological Properties of Non-Newtonian Materials by Rotational (Brookfield type) Viscometer.

1.3.1.7 ASTM D 2939 - Standard Test Methods for Emulsified Bitumens Used as Protective Coatings.

1.3.1.8 ASTM D 3273 Standard Test Method for Resistance to Growth of Mold on the Surface of Interior Coatings in an Environmental Chamber.

07 14 00-1

1.3.1.9 ASTM D 3274 Standard Test Method for Evaluating Degrees of Surface Disfigurement of Paint Films by Microbial (Fungal or Algal) Growth or Soil and Dirt Accumulation.

1.3.1.10 ASTM D 3409 - Standard Test Method for Adhesion of Asphalt-Roof Cement to Damp, Wet, or Underwater Surfaces.

1.3.1.11 ASTM D 4258 - Standard Practice for Surface Cleaning Concrete for Coating.1.3.1.12 ASTM D 4586 - Standard Specification for Asphalt Roof Cement, Asbestos-Free.1.3.1.13 ASTM E 96 - Standard Test Method for Water Vapor Transmission of Materials.1.3.1.14 ASTM E 283 - Standard Test Method for Determining Rate of Air Leakage

Through Exterior Windows, Curtain Walls, and Doors Under Specified Pressure Differences Across the Specimen.

1.4 SUBMITTALS

1.4.1 Submit under provisions of Section 01 30 00 - Administrative Requirements.

1.4.2 Product Data: Manufacturer's data sheets on each product to be used, including:1.4.2.1 Preparation instructions and recommendations.1.4.2.2 Storage and handling requirements and recommendations.1.4.2.3 Installation methods.

1.4.3 Quality Assurance/Control Submittals: Submit the following1.4.3.1 Certificates: Submit certificate that applicator complies with requirements of this

section.

1.5 QUALITY ASSURANCE

1.5.1 Applicator Qualifications: Utilize an applicator trained and approved by the waterproofing manufacturer.

1.5.2 Regulatory Requirements and Approvals: Comply with requirements of the following:1.5.2.1 ICC Evaluation Services, Inc. (ICC) ESR-3062.

1.5.3 Mock-Up: Provide a mock-up for evaluation of surface preparation techniques and application workmanship.1.5.3.1 Finish areas designated by Architect.1.5.3.2 Do not proceed with remaining work until workmanship is approved by Architect.1.5.3.3 Refinish mock-up area as required to produce acceptable work.

1.6 DELIVERY, STORAGE, AND HANDLING

1.6.1 Store products in manufacturer's unopened packaging until ready for installation.

1.6.2 Storage and Protection: Store materials protected from exposure to harmful environmental conditions and at temperature and humidity conditions recommended by the manufacturer.

1.6.3 Store and dispose of solvent-based materials, and materials used with solvent-based materials, in accordance with requirements of local authorities having jurisdiction.

1.7 PROJECT CONDITIONS

1.7.1 Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's absolute limits.1.7.1.1 Environmental Requirements: Comply with application temperature range of 0 to

150 degrees F (-18 to 66 degrees C) for Solvent-Based product and 20 to 130 degrees F (-7 to 55 degrees C) for Water-Based product.

07 14 00-2

1.8 WARRANTY

1.8.1 Commercial Warranty: The special warranty specified in this Article shall not deprive the Owner of other rights the Owner may have under other provisions of the Contract Documents, and shall be in addition to, and run concurrent with, other warranties made by the Contractor under requirements of the Contract Documents.1.8.1.1 Commercial Warranty: Below grade.

1.8.1.1.1 Membrane: Mar-flex 5000.1.8.1.1.2 Membrane: ProVention 363.1.8.1.1.3 Commercial Drainage Board: DrainCore Dimpleboard Type II.1.8.1.1.4 Commercial Drainage Board: Geo-Mat Plus.1.8.1.1.5 Commercial Drainage Board: ShockWave.

1.8.1.2 Commercial Warranty: Above grade.1.8.1.2.1 Membrane: Air and Vapor Barrier 1800.1.8.1.2.2 Membrane: Air Barrier 1200 VP.

1.8.1.3 Provide written warranty signed by waterproofing manufacturer and installer agreeing to repair or replace waterproofing that does not meet requirements or that does not remain watertight within the specified warranty period.

1.8.1.3.1 Warranty Period: 5 years after date of Substantial Completion.1.8.1.3.2 Warranty does not include failure of waterproofing due to failure of

substrate or formation of new joints and cracks in substrate that exceed 1/16 inch (1.6 mm) in width.

1.8.2 Residential Warranty: The special warranty specified in this Article shall not deprive the Owner of other rights the Owner may have under other provisions of the Contract Documents, and shall be in addition to, and run concurrent with, other warranties made by the Contractor under requirements of the Contract Documents.1.8.2.1 Standard Residential Warranty:

1.8.2.1.1 Membrane: Mar-flex 5000.1.8.2.1.2 Drainage Board: None.1.8.2.1.3 Warranty Period: 15 Years.

1.8.2.2 Bronze Warranty:1.8.2.2.1 Membrane: Mar-flex 5000.1.8.2.2.2 Drainage Board: Geo-Mat Plus Roll.1.8.2.2.3 Drainage Board: 3/4 inch (19 mm) Drain and Dry.1.8.2.2.4 Drainage Board: Type I DrainCore Dimpleboard.1.8.2.2.5 Warranty Period: 40 Years.

1.8.2.3 Silver Warranty:1.8.2.3.1 Membrane: Mar-flex 5000.1.8.2.3.2 Drainage Board: 1 inch (25 mm) Shockwave.1.8.2.3.3 Drainage Board: 1-3/16 inches (30 mm) Drain and Dry.1.8.2.3.4 Warranty Period: 50 Years.

1.8.2.4 Gold Warranty:1.8.2.4.1 Membrane: Mar-flex 5000.1.8.2.4.2 Drainage Board: 2 inch (51 mm) Shockwave.1.8.2.4.3 Drainage Board: 2-3/8 inches (60 mm) Drain and Dry.1.8.2.4.4 Warranty Period: 60 Years.

1.8.2.5 Standard Warranty:1.8.2.5.1 Membrane: Fusion UV Water-based.1.8.2.5.2 Membrane: Fusion solvent-based.1.8.2.5.3 Drainage Board: None.1.8.2.5.4 Warranty Period: 15 Years.

1.8.2.6 Premium Warranty:1.8.2.6.1 Membrane: Fusion UV Water-based.1.8.2.6.2 Membrane: Fusion solvent-based.1.8.2.6.3 Drainage Board: Geo-Mat Plus Roll.

07 14 00-3

1.8.2.6.4 Drainage Board: Drain and Dry.1.8.2.6.5 Drainage Board: Shockwave.1.8.2.6.6 Drainage Board: Type I DrainCore Dimpleboard.1.8.2.6.7 Warranty Period: Limited Lifetime.

1.8.2.7 Standard Warranty:1.8.2.7.1 Membrane: QuickSeal SB.1.8.2.7.2 Membrane: QuickSeal WB.1.8.2.7.3 Drainage Board: None.1.8.2.7.4 Warranty Period: 10 Years.

1.8.2.8 Premium Warranty:1.8.2.8.1 Membrane: QuickSeal SB.1.8.2.8.2 Membrane: QuickSeal WB.1.8.2.8.3 Drainage Board: Geo-Mat Plus Roll.1.8.2.8.4 Drainage Board: Drain and Dry.1.8.2.8.5 Drainage Board: Shockwave.1.8.2.8.6 Drainage Board: Type I DrainCore Dimpleboard.1.8.2.8.7 Warranty Period: 20 Years.

2 PRODUCTS

2.1 MANUFACTURERS

2.1.1 Acceptable Manufacturer: Mar-Flex Waterproofing & Building Products, which is located at: P. O. BOX 8256 500 Business Pkwy.; Carlisle, OH 45005; Toll Free Tel: 800-498-1411; Tel: 513-422-7285; Fax: 513-422-7282; Email:request info (info@mar-flex.com); Web:www.mar-flex.com

2.1.2 Substitutions: Not permitted.

2.1.3 Requests for substitutions will be considered in accordance with provisions of Section 01 60 00 - Product Requirements.

2.2 WATERPROOFING SYSTEM - GENERAL

2.2.1 General: Provide waterproofing systems that prevent the passage of liquid water under hydrostatic pressure and that comply with specified physical requirements as demonstrated by testing performed by independent testing agency on manufacturer's current waterproofing formulations and system design; use materials specified below.

2.2.2 Foundation Walls: Use specified materials in following assembly.2.2.2.1 First Course: Mar-flex ProVention 363 or 5000 Waterproofing Membrane as

scheduled or indicated.2.2.2.2 Second Course: Mar-flex's Commercial Boards as scheduled or indicated.2.2.2.3 Third Course: Mar-flex 523 DrainAway 12 inches (305 mm) Drainage Tile.2.2.2.4 Provide installed assembly to comply with warranty as specified.

2.2.3 Foundation Walls: Use specified materials in following assembly.2.2.3.1 First Course: Mar-flex Waterproofing Membrane as scheduled or indicated.2.2.3.2 Second Course: Mar-flex's Boards as scheduled or indicated.2.2.3.3 Third Course: Mar-flex 523 DrainAway 6 inches (152 mm) Drainage Tile.2.2.3.4 Provide installed assembly to comply with warranty as specified.

2.2.4 Horizontal Decks: Use specified materials in following assembly.2.2.4.1 First Course: Mar-flex ProVention 363 or 5000 Waterproofing Membrane as

scheduled or indicated.2.2.4.2 Second Course: Mar-flex's Commercial Type III Boards as scheduled or

indicated.

07 14 00-4

2.2.4.3 Third Course: Mar-flex 523 DrainAway 12 inches (305 mm) Drainage Tile2.2.4.4 Fourth Course: Top layer will vary with design. _______________2.2.4.5 Provide installed assembly to comply with warranty as specified.

2.2.5 Horizontal Decks: Use specified materials in following assembly.2.2.5.1 First Course: Mar-flex 5000 Waterproofing Membrane as scheduled or indicated.2.2.5.2 Second Course: Mar-flex's Type III Boards as scheduled or indicated.2.2.5.3 Third Course: Mar-flex 523 DrainAway 12 inches (305 mm) Drainage Tile2.2.5.4 Fourth Course: Top layer will vary with design. _______________2.2.5.5 Provide installed assembly to comply with warranty as specified.

2.3 ABOVE GRADE AIR/VAPOR BARRIER SYSTEM - GENERAL

2.3.1 General: Provide air/barrier systems that prevent the passage of liquid water, water vapor and air under tested conditions and that comply with specified physical requirements as demonstrated by testing performed by independent testing agency on manufacturer's current formulations and system design; use materials specified below.

2.3.2 Air/Vapor Barrier: Use specified materials in following assembly.2.3.2.1 Detail area with primer and transition strip.2.3.2.2 Apply air/vapor membrane to surface per specifications.2.3.2.3 Provide installed assembly to comply with warranty as specified.

2.4 BELOW GRADE FOUNDATION AND RETAINING WALL WATERPROOFING

2.4.1 Solvent Based Fluid Applied Waterproofing:2.4.1.1 Product: Mar-flex 5000 SB Waterproofing Membrane as manufactured by Mar-

flex Waterproofing and Building Products:2.4.1.1.1 Material: Polymer Modified Asphalt Membrane.2.4.1.1.2 Color: Black.2.4.1.1.3 Total Solids: 70 - 75 percent.2.4.1.1.4 Application Method: Spray.2.4.1.1.5 Application Method: Brush.2.4.1.1.6 Application Method: Roll.2.4.1.1.7 Coverage Rate: 4 gal/100 sf (1.4 l/sm).2.4.1.1.8 Film Thickness, Dry: 60 mil (1.5 mm) minimum.2.4.1.1.9 Total Cure Time: 24 hours.2.4.1.1.10 Weight/Gallon: 7.6 lb (3.4 kg).2.4.1.1.11 Elongation at 70 degrees F (21 degrees C) (ASTM D 412 Die C): 1725

percent.2.4.1.1.12 Tensile Strength (ASTM C 719): 48 psi (331 kPa).2.4.1.1.13 Low Temperature Flexibility at -15 degrees F (ASTM C 719): No cracking.2.4.1.1.14 Crack Bridging (ASTM C 836): 10 cycles without bond failure.2.4.1.1.15 Resistance to Water Flow (ASTM D 466): Bond strength not affected.2.4.1.1.16 Water Solubility (ASTM D 2939): No blistering or re-emulsion.2.4.1.1.17 Resistance to Hydrostatic Pressure (Federal Spec TT-C 555B, Par. 4.4.7.):

2.4.1.1.17.1 Water Leaks: None.2.4.1.1.17.2 Weight Gain: None.

2.4.1.1.18 Permeability: 0.23 perms (13 ng/(Pa X s X m2).2.4.1.1.19 Water Vapor (ASTM E 96):

2.4.1.1.19.1 Transmission: 0.11 grains/sf/h.2.4.1.1.19.2 Permeability: 0.23 perms (13 ng/(Pa X s X m2).

2.4.2 Water Based Fluid Applied Waterproofing:2.4.2.1 Product: Mar-flex 5000 WB Waterproofing Membrane as manufactured by Mar-

flex Waterproofing and Building Products.2.4.2.1.1 Material: Emulsion.

07 14 00-5

2.4.2.1.2 Color: Black2.4.2.1.3 Total Solids: 60-70 percent.2.4.2.1.4 Application Method: Spray.2.4.2.1.5 Application Method: Brush.2.4.2.1.6 Application Method: Roll.2.4.2.1.7 Coverage Rate: 5-gal/100 sf (1.75 l/sm).2.4.2.1.8 Film Thickness, Dry: 60 mil (1.5 mm) minimum.2.4.2.1.9 Total Cure Time: 24 hours.2.4.2.1.10 Weight/Gallon: 7.6 lb (3.4 kg).2.4.2.1.11 Elongation at 70 degrees F (21 degrees C) (ASTM D 412 Die C): 1725

percent.2.4.2.1.12 Tensile Strength (ASTM C 719): 48 psi (331 kPa).2.4.2.1.13 Low Temperature Flexibility at -15 degrees F (ASTM C 719): No cracking.2.4.2.1.14 Crack Bridging (ASTM C 836): 10 cycles without bond failure.2.4.2.1.15 Viscosity/Centipoise: (ASTM D 2196): 3600 centipoise.2.4.2.1.16 Resistance to Water Flow (ASTM D 466): Bond strength not affected.2.4.2.1.17 Water Solubility (ASTM D 2939): No blistering or re-emulsion.2.4.2.1.18 Resistance to Hydrostatic Pressure (Federal Spec TT-C 555B, Par. 4.4.7.):

2.4.2.1.18.1 Water Leaks: None.2.4.2.1.18.2 Weight Gain: None.

2.4.2.1.19 Permeability: 0.23 perms (13 ng/(Pa X s X m2).2.4.2.1.20 Water Vapor (ASTM E 96):

2.4.2.1.20.1 Transmission: 0.11 grains/sf/h.2.4.2.1.20.2 Permeability: 0.23 perms (13 ng/(Pa X s X m2).

2.4.3 Solvent Based Fluid Applied Waterproofing:2.4.3.1 Product: Mar-flex ProVention 363 SB Waterproofing Membrane as manufactured

by Mar-flex Waterproofing and Building Products.2.4.3.1.1 Material: Polymer Modified Asphalt Membrane.2.4.3.1.2 Color: Black.2.4.3.1.3 Total Solids: 70 to 75 percent2.4.3.1.4 Application Method: Spray.2.4.3.1.5 Application Method: Brush.2.4.3.1.6 Application Method: Roll.2.4.3.1.7 Coverage Rate: 5-gal/100 sf (1.75 l/sm).2.4.3.1.8 Film Thickness, Dry: 60 mil (1.5 mm) minimum.2.4.3.1.9 Total Cure Time: 24 hours.2.4.3.1.10 Weight/Gallon: 7.8 lb (3.4 kg).2.4.3.1.11 Elongation at 70 degrees F (21 degrees C) (ASTM D 412 Die C): 1672

percent.2.4.3.1.12 Tensile Strength (ASTM C 719): 56.4 psi (331 kPa).2.4.3.1.13 Low Temperature Flexibility at -15 degrees F (-26 degrees C) (ASTM C

719): No cracking.2.4.3.1.14 Crack Bridging (ASTM C 836): 10 cycles without bond failure.2.4.3.1.15 Viscosity/Centipoise: (ASTM D 2196): 3600 centipoise.2.4.3.1.16 Resistance to Water Flow (ASTM D 466): Bond strength not affected.2.4.3.1.17 Water Solubility (ASTM D 2939): No blistering or re-emulsion.2.4.3.1.18 Resistance to Hydrostatic Pressure (Federal Spec TT-C 555B, Par. 4.4.7.):

2.4.3.1.18.1 Water Leaks: None.2.4.3.1.18.2 Weight Gain: None.

2.4.3.1.19 Permeability: 0.23 perms.2.4.3.1.20 Water Vapor (ASTM E 96):

2.4.3.1.20.1 Transmission: 0.11 grains/sf/h.2.4.3.1.20.2 Permeability: 0.23 perms.

2.4.4 Water Based Fluid Applied Waterproofing:

07 14 00-6

2.4.4.1 Product: Mar-flex ProVention 363 WB Waterproofing Membrane as manufactured by Mar-flex Waterproofing and Building Products.

2.4.4.1.1 Material: Emulsion.2.4.4.1.2 Color: Black.2.4.4.1.3 Total Solids: 60 to 70 percent.2.4.4.1.4 Application Method: Spray.2.4.4.1.5 Application Method: Brush.2.4.4.1.6 Application Method: Roll.2.4.4.1.7 Coverage Rate: 5-gal/100 sf (1.75 l/sm).2.4.4.1.8 Film Thickness, Dry: 60 mil (1.5 mm) minimum.2.4.4.1.9 Total Cure Time: 24 hours.2.4.4.1.10 Weight/Gallon: 7.6 lb (3.4 kg).2.4.4.1.11 Elongation at 70 degrees F (21 degrees C) (ASTM D 412 Die C): 1725

percent.2.4.4.1.12 Tensile Strength (ASTM C 719): 48 psi (331 kPa).2.4.4.1.13 Low Temperature Flexibility at -15 degrees F (-26 degrees C) (ASTM C

719): No cracking.2.4.4.1.14 Crack Bridging (ASTM C 836): 10 cycles without bond failure.2.4.4.1.15 Viscosity/Centipoise: (ASTM D 2196): 3600 centipoise.2.4.4.1.16 Resistance to Water Flow (ASTM D 466): Bond strength not affected.2.4.4.1.17 Water Solubility (ASTM D 2939): No blistering or re-emulsion.2.4.4.1.18 Resistance to Hydrostatic Pressure (Federal Spec TT-C 555B, Par. 4.4.7.):

2.4.4.1.18.1 Water Leaks: None.2.4.4.1.18.2 Weight Gain: None.

2.4.4.1.19 Permeability: 0.23 perms.2.4.4.1.20 Water Vapor (ASTM E 96):

2.4.4.1.20.1 Transmission: 0.11 grains/sf/h.2.4.4.1.20.2 Permeability: 0.23 perms.

2.5 HORIZONTAL CONCRETE WATERPROOFING

2.5.1 Water Based Fluid Applied Waterproofing:2.5.1.1 Product: Mar-flex 5000 WB Waterproofing Membrane as manufactured by Mar-

flex Waterproofing and Building Products.2.5.1.1.1 Material: Emulsion.2.5.1.1.2 Color: Black.2.5.1.1.3 Total Solids: 70-75 percent.2.5.1.1.4 Application Method: Spray.2.5.1.1.5 Application Method: Brush.2.5.1.1.6 Application Method: Roll.2.5.1.1.7 Coverage Rate: 5-gal/100 sf (1.75 l/sm).2.5.1.1.8 Film Thickness, Dry: 60 mil (1.5 mm) minimum.2.5.1.1.9 Total Cure Time: 24 hours.2.5.1.1.10 Weight/Gallon: 7.6 lb (3.4 kg).2.5.1.1.11 Elongation at 70 degree F (21 degree C) (ASTM D 412 Die C): 1725

percent.2.5.1.1.12 Tensile Strength (ASTM C 719): 48 psi (331 kPa).2.5.1.1.13 Low Temperature Flexibility at -15 degree F (ASTM C 719): No cracking.2.5.1.1.14 Crack Bridging (ASTM C 836): 10 cycles without bond failure.2.5.1.1.15 Viscosity/Centipoise: (ASTM D 2196): 3600 centipoise2.5.1.1.16 Resistance to Water Flow (ASTM D 466): Bond strength not affected.2.5.1.1.17 Water Solubility (ASTM D 2939): No blistering or re-emulsion.2.5.1.1.18 Resistance to Hydrostatic Pressure (Federal Spec TT-C 555B, Par. 4.4.7.):

2.5.1.1.18.1 Water Leaks: None.2.5.1.1.18.2 Weight Gain: None.

2.5.1.1.19 Permeability: 0.23 perms (13 ng/(Pa X s X m2).

07 14 00-7

2.5.1.1.20 Water Vapor (ASTM E 96):2.5.1.1.20.1 Transmission: 0.11 grains/sf/h.2.5.1.1.20.2 Permeability: 0.23 perms (13 ng/(Pa X s X m2).

2.5.2 Solvent Based Fluid Applied Waterproofing:2.5.2.1 Product: Mar-flex 5000 SB Waterproofing Membrane as manufactured by Mar-

flex Waterproofing and Building Products.2.5.2.1.1 Material: Polymer Modified Asphalt Membrane.2.5.2.1.2 Color: Black.2.5.2.1.3 Total Solids: 70 - 75 percent.2.5.2.1.4 Application Method: Spray.2.5.2.1.5 Application Method: Brush.2.5.2.1.6 Application Method: Roll.2.5.2.1.7 Coverage Rate: 4 gal/100 sf (1.4 l/sm).2.5.2.1.8 Film Thickness, Dry: 60 mil (1.5 mm) minimum.2.5.2.1.9 Total Cure Time: 24 hours.2.5.2.1.10 Weight/Gallon: 7.6 lb (3.4 kg).2.5.2.1.11 Elongation at 70 degrees F (21 degrees C) (ASTM D 412 Die C): 1725

percent.2.5.2.1.12 Tensile Strength (ASTM C 719): 48 psi (331 kPa).2.5.2.1.13 Low Temperature Flexibility at -15 degrees F (ASTM C 719): No cracking.2.5.2.1.14 Crack Bridging (ASTM C 836): 10 cycles without bond failure.2.5.2.1.15 Resistance to Water Flow (ASTM D 466): Bond strength not affected.2.5.2.1.16 Water Solubility (ASTM D 2939): No blistering or re-emulsion.2.5.2.1.17 Resistance to Hydrostatic Pressure (Federal Spec TT-C 555B, Par. 4.4.7.):

2.5.2.1.17.1 Water Leaks: None2.5.2.1.17.2 Weight Gain: None

2.5.2.1.18 Permeability: 0.23 perms (13 ng/(Pa X s X m2).2.5.2.1.19 Water Vapor (ASTM E 96):

2.5.2.1.19.1 Transmission: 0.11 grains/sf/h.2.5.2.1.19.2 Permeability: 0.23 perms (13 ng/(Pa X s X m2).

2.5.3 Water Based Fluid Applied Waterproofing:2.5.3.1 Product: Mar-flex ProVention 363 WB Waterproofing Membrane as

manufactured by Mar-flex Waterproofing and Building Products.2.5.3.1.1 Material: Emulsion.2.5.3.1.2 Color: Black.2.5.3.1.3 Total Solids: 60 to 70 percent.2.5.3.1.4 Application Method: Spray.2.5.3.1.5 Application Method: Brush.2.5.3.1.6 Application Method: Roll.2.5.3.1.7 Coverage Rate: 5-gal/100 sf (1.75 l/sm).2.5.3.1.8 Film Thickness, Dry: 60 mil (1.5 mm) minimum.2.5.3.1.9 Total Cure Time: 24 hours.2.5.3.1.10 Weight/Gallon: 7.6 lb (3.4 kg).2.5.3.1.11 Elongation at 70 degrees F (21 degrees C) (ASTM D 412 Die C): 1725

percent.2.5.3.1.12 Tensile Strength (ASTM C 719): 48 psi (331 kPa).2.5.3.1.13 Low Temperature Flexibility at -15 degrees F (-26 degrees C) (ASTM C

719): No cracking.2.5.3.1.14 Crack Bridging (ASTM C 836): 10 cycles without bond failure.2.5.3.1.15 Viscosity/Centipoise: (ASTM D 2196): 3600 centipoise.2.5.3.1.16 Resistance to Water Flow (ASTM D 466): Bond strength not affected.2.5.3.1.17 Water Solubility (ASTM D 2939): No blistering or re-emulsion.2.5.3.1.18 Resistance to Hydrostatic Pressure (Federal Spec TT-C 555B, Par. 4.4.7.):

2.5.3.1.18.1 Water Leaks: None.

07 14 00-8

2.5.3.1.18.2 Weight Gain: None.2.5.3.1.19 Permeability: 0.23 perms.2.5.3.1.20 Water Vapor (ASTM E 96):

2.5.3.1.20.1 Transmission: 0.11 grains/sf/h.2.5.3.1.20.2 Permeability: 0.23 perms.

2.5.4 Solvent Based Fluid Applied Waterproofing:2.5.4.1 Product: Mar-flex ProVention 363 SB Waterproofing Membrane as

manufactured by Mar-flex Waterproofing and Building Products.2.5.4.1.1 Material: Polymer Modified Asphalt Membrane.2.5.4.1.2 Color: Black.2.5.4.1.3 Total Solids: 70 to 75 percent.2.5.4.1.4 Application Method: Spray.2.5.4.1.5 Application Method: Brush.2.5.4.1.6 Application Method: Roll.2.5.4.1.7 Coverage Rate: 5-gal/100 sf (1.75 l/sm).2.5.4.1.8 Film Thickness, Dry: 60 mil (1.5 mm) minimum.2.5.4.1.9 Total Cure Time: 24 hours.2.5.4.1.10 Weight/Gallon: 7.8 lb (3.4 kg).2.5.4.1.11 Elongation at 70 degrees F (21 degrees C) (ASTM D 412 Die C): 1672

percent.2.5.4.1.12 Tensile Strength (ASTM C 719): 56.4psi (331 kPa).2.5.4.1.13 Low Temperature Flexibility at -15 degrees F (-26 degrees C) (ASTM C

719): No cracking.2.5.4.1.14 Crack Bridging (ASTM C 836): 10 cycles without bond failure.2.5.4.1.15 Viscosity/Centipoise: (ASTM D 2196): 3600 centipoise.2.5.4.1.16 Resistance to Water Flow (ASTM D 466): Bond strength not affected.2.5.4.1.17 Water Solubility (ASTM D 2939): No blistering or re-emulsion.2.5.4.1.18 Resistance to Hydrostatic Pressure (Federal Spec TT-C 555B, Par. 4.4.7.):

2.5.4.1.18.1 Water Leaks: None.2.5.4.1.18.2 Weight Gain: None.

2.5.4.1.19 Permeability: 0.23 perms.2.5.4.1.20 Water Vapor (ASTM E 96):

2.5.4.1.20.1 Transmission: 0.11 grains/sf/h.2.5.4.1.20.2 Permeability: 0.23 perms.

2.6 AIR/VAPOR BARRIER WATERPROOFING

2.6.1 UV Resistant Solvent Based Fluid Applied Air/Vapor Barrier:2.6.1.1 Product: Mar-flex Air and Vapor Barrier 1800 as manufactured by Mar-flex

Waterproofing and Building Products.2.6.1.1.1 Material: 100 percent rubber polymer, solvent based.2.6.1.1.2 Color: Gray.2.6.1.1.3 Application Method: Spray.2.6.1.1.4 Application Method: Brush.2.6.1.1.5 Application Method: Roll.2.6.1.1.6 Coverage Rate: 1-gal/23-30 sf (1.36-1.77 l/sm).2.6.1.1.7 Film Thickness, Dry: 40 mil (1.0 mm) minimum.2.6.1.1.8 Initial Dry Time: 12 hours .2.6.1.1.9 Elongation (ASTM D 412 Die C): 1800 percent.2.6.1.1.10 Air Leakage Rate: (ASTM E 283): Less than 0.0004 cfm/sf.2.6.1.1.11 Water Vapor Permeance (ASTM E 96): 0.08 perms.2.6.1.1.12 Water-Tightness CGSB 37.58-M86: Pass.2.6.1.1.13 UV Exposure: 30 Days.2.6.1.1.14 Application Temperature: Minimum 15 degrees F.2.6.1.1.15 Liquid Water Absorption (ASTM D 95): Less than 0.05 percent (weight).

07 14 00-9

2.6.2 Water Based Fluid Applied Air/Vapor Barrier:2.6.2.1 Product: Mar-flex Air Barrier 1200 VP as manufactured by Mar-flex

Waterproofing and Building Products.2.6.2.1.1 Color: Gray.2.6.2.1.2 Application Method: Spray.2.6.2.1.3 Application Method: Brush.2.6.2.1.4 Application Method: Roll.2.6.2.1.5 Coverage Rate: 1-gal/23-30sf (1.36-1.77 l/sm).2.6.2.1.6 Film Thickness: Dry, 40 mil (1.0 mm) minimum.2.6.2.1.7 Dry Time: 12-24 hours.2.6.2.1.8 Elongation (ASTM D 412 Die C): 1800 percent.2.6.2.1.9 UV Exposure: Unlimited.2.6.2.1.10 Application Temperature: Minimum 41 degrees F.2.6.2.1.11 Air Leakage (ASTM E 96): Less than 0.004 CFM/sf.2.6.2.1.12 Vapor Permeance (ASTM E 96): 12.0 Perms.2.6.2.1.13 Water-Tightness (CGSB 37.58-M86): Pass.

2.7 BELOW GRADE FOUNDATION WATERPROOFING

2.7.1 Solvent Based Fluid Applied Waterproofing:2.7.1.1 Product: Mar-flex 5000 SB Waterproofing Membrane as manufactured by Mar-

flex Waterproofing and Building Products.2.7.1.1.1 Material: Polymer Modified Asphalt Membrane.2.7.1.1.2 Color: Black.2.7.1.1.3 Total Solids: 70 - 75 percent.2.7.1.1.4 Application Method: Spray.2.7.1.1.5 Application Method: Brush.2.7.1.1.6 Application Method: Roll.2.7.1.1.7 Coverage Rate: 4 gal/100 sf (1.4 l/sm).2.7.1.1.8 Film Thickness, Dry: 60 mil (1.5 mm) minimum.2.7.1.1.9 Total Cure Time: 24 hours.2.7.1.1.10 Weight/Gallon: 7.6 lb (3.4 kg).2.7.1.1.11 Elongation at 70 degree F (21 degree C) (ASTM D 412 Die C): 1725

percent.2.7.1.1.12 Tensile Strength (ASTM C 719): 48 psi (331 kPa).2.7.1.1.13 Low Temperature Flexibility at -15 degree F (ASTM C 719): No cracking.2.7.1.1.14 Crack Bridging (ASTM C 836): 10 cycles without bond failure.2.7.1.1.15 Resistance to Water Flow (ASTM D 466): Bond strength not affected.2.7.1.1.16 Water Solubility (ASTM D 2939): No blistering or re-emulsion2.7.1.1.17 Resistance to Hydrostatic Pressure (Federal Spec TT-C 555B, Par. 4.4.7.):

2.7.1.1.17.1 Water Leaks: None2.7.1.1.17.2 Weight Gain: None

2.7.1.1.18 Permeability: 0.23 perms (13 ng/(Pa X s X m2).2.7.1.1.19 Water Vapor (ASTM E 96):

2.7.1.1.19.1 Transmission: 0.11 grains/sf/h.2.7.1.1.19.2 Permeability: 0.23 perms (13 ng/(Pa X s X m2).

2.7.2 Water Based Fluid Applied Waterproofing2.7.2.1 Product: Mar-flex 5000 WB Waterproofing Membrane as manufactured by Mar-

flex Waterproofing and Building Products.2.7.2.1.1 Material: Emulsion.2.7.2.1.2 Color: Black2.7.2.1.3 Total Solids: 60-70 percent2.7.2.1.4 Application Method: Spray.2.7.2.1.5 Application Method: Brush.2.7.2.1.6 Application Method: Roll.

07 14 00-10

2.7.2.1.7 Coverage Rate: 5-gal/100 sf (1.75 l/sm).2.7.2.1.8 Film Thickness, Dry: 60 mil (1.5 mm) minimum.2.7.2.1.9 Total Cure Time: 24 hours.2.7.2.1.10 Weight/Gallon: 7.6 lb (3.4 kg).2.7.2.1.11 Elongation at 70 degree F (21 degree C) (ASTM D 412 Die C): 1725

percent.2.7.2.1.12 Tensile Strength (ASTM C 719): 48 psi (331 kPa).2.7.2.1.13 Low Temperature Flexibility at -15 degree F (ASTM C 719): No cracking.2.7.2.1.14 Crack Bridging (ASTM C 836): 10 cycles without bond failure.2.7.2.1.15 Viscosity/Centipoise: (ASTM D 2196): 3600 centipoise.2.7.2.1.16 Resistance to Water Flow (ASTM D 466): Bond strength not affected.2.7.2.1.17 Water Solubility (ASTM D 2939): No blistering or re-emulsion.2.7.2.1.18 Resistance to Hydrostatic Pressure (Federal Spec TT-C 555B, Par. 4.4.7.):

2.7.2.1.18.1 Water Leaks: None.2.7.2.1.18.2 Weight Gain: None.

2.7.2.1.19 Permeability: 0.23 perms (13 ng/(Pa X s X m2).2.7.2.1.20 Water Vapor (ASTM E 96):

2.7.2.1.20.1 Transmission: 0.11 grains/sf/h.2.7.2.1.20.2 Permeability: 0.23 perms (13 ng/(Pa X s X m2).

2.7.3 Solvent Based Fluid Applied Waterproofing:2.7.3.1 Product: Mar-flex Fusion SB Waterproofing Membrane as manufactured by Mar-

flex Waterproofing and Building Products.2.7.3.1.1 Material: Highly elastic thermoplastic exterior waterproof coating.2.7.3.1.2 Color: Gray.2.7.3.1.3 Total Solids: 58 percent.2.7.3.1.4 Density: 7.6 lb (3.4 kg).2.7.3.1.5 Application Method: Spray.2.7.3.1.6 Application Method: Brush.2.7.3.1.7 Application Method: Roll.2.7.3.1.8 Application Temp (Ambient) 15 degree to 150 degree F (-9 degree C to 56

degree C).2.7.3.1.9 Film Thickness, Dry: 60 mil (1.5 mm) minimum.2.7.3.1.10 Total Cure Time: 24 hours.2.7.3.1.11 Adhesion to Concrete: No Adhesion Loss.2.7.3.1.12 Elongation at 70 degree F (21 degree C) (ASTM D 412 Die C): 1800

percent.2.7.3.1.13 Low Temperature Flexibility at -15 degree F (-26 degree C) (ASTM C 719):

No cracking.2.7.3.1.14 Crack Bridging (ASTM C 836): 10 cycles without bond failure.2.7.3.1.15 Water Vapor Permeance (40 mil (1.0 mm) dry coating): 0.13 perm

(grains/sqft/h).2.7.3.1.16 Liquid Water Absorption: 1.0 oz (31 grms) Absorption/No Leaks.2.7.3.1.17 Mold Growth/Bacterial Attack: No Degradation.2.7.3.1.18 Resistance to Hydrostatic Pressure Head: No Water Infiltration.2.7.3.1.19 Coverage Rate: 5 gal./100 sf (1.75 l/sm).2.7.3.1.20 Tensile Strength (ASTM C 719): 32 psi (221 kPa).

2.7.4 UV Resistant Water Based Fluid Applied Waterproofing:2.7.4.1 Product: Mar-flex Fusion UV WB Waterproofing Membrane as manufactured by

Mar-flex Waterproofing and Building Products.2.7.4.1.1 Material: 100 percent virgin-polymer.2.7.4.1.2 Color: Gray2.7.4.1.3 Total Solids: 55-57 percent.2.7.4.1.4 Application Method: Spray.2.7.4.1.5 Application Method: Brush.

07 14 00-11

2.7.4.1.6 Application Method: Roll.2.7.4.1.7 Coverage Rate: 5-gal/100 sf. (1.75 l/sm)2.7.4.1.8 Film Thickness, Dry: 60 mil (1.5 mm) minimum.2.7.4.1.9 Total Cure Time: 24 hours.2.7.4.1.10 Weight/Gallon: 7.6 lb (3.4 kg).2.7.4.1.11 Elongation at 70 degree F (21 degree C) (ASTM D 412 Die C): 1500

percent.2.7.4.1.12 Tensile Strength (ASTM C 719): 150 psi (1034 kPa).2.7.4.1.13 Low Temperature Flexibility at -15 degree F (-26 degree C) (ASTM C 719):

No cracking.2.7.4.1.14 Crack Bridging (ASTM C 836): 10 cycles without bond failure.2.7.4.1.15 Resistance to Water Flow (ASTM D 466): Bond strength not affected.2.7.4.1.16 Water Solubility (ASTM D 2939): No blistering or re-emulsion.2.7.4.1.17 Resistance to Hydrostatic Pressure (Federal Spec TT-C 555B, Par. 4.4.7.):

2.7.4.1.17.1 Water Leaks: None.2.7.4.1.17.2 Weight Gain: None.

2.7.4.1.18 Permeability: 0.13 perms2.7.4.1.19 Water Vapor (ASTM E 96):

2.7.4.1.19.1 Transmission: 0.11 grains/sf/h.2.7.4.1.19.2 Permeability: 0.13 perms.

2.7.5 Water Based Fluid Applied Waterproofing:2.7.5.1 Product: Mar-flex Quickseal WB as manufactured by Mar-flex Waterproofing

and Building Products.2.7.5.1.1 Material: Emulsion.2.7.5.1.2 Color: Black.2.7.5.1.3 Total Solids: 60 to 70 percent.2.7.5.1.4 Application Method: Spray.2.7.5.1.5 Application Method: Brush.2.7.5.1.6 Application Method: Roll.2.7.5.1.7 Elongation at 70 degree F (21 degree C): 850 percent minimum.2.7.5.1.8 Total Cure Time: 24 hours.2.7.5.1.9 Tensile Strength (ASTM D 412): 32 psi (221 kPa).2.7.5.1.10 Weight/Gallon: 7.7 lb (3.5 kg).2.7.5.1.11 Coverage Rate: 3.3 to 5.0 gal/100 sf (1.2 to 1.75 l/sm).2.7.5.1.12 Film Thickness, Dry: 60 mil (1.5 mm) minimum.2.7.5.1.13 Crack Bridging (ASTM C 836): 10 cycles without bond failure.2.7.5.1.14 Resistance to Water Flow (ASTM D 466): Bond strength not affected.2.7.5.1.15 Water Solubility (ASTM D 2939): No blistering or re-emulsion.2.7.5.1.16 Water Vapor (ASTM E 96):

2.7.5.1.16.1 Transmission: 0.12 grains/sf/h.2.7.5.1.16.2 Permeability: 0.28 perms (16 ng/(Pa X s X m2).

2.7.5.1.17 Resistance to Growth of Mold - Surface Disfigurement (ASTM D 3273, ASTM D 3274): None.

2.7.6 Solvent Based Fluid Applied Waterproofing:2.7.6.1 Product: Mar-flex Quickseal SB as manufactured by Mar-flex Waterproofing and

Building Products.2.7.6.1.1 Material: Seamless Modified Polymer Membrane.2.7.6.1.2 Color: Black.2.7.6.1.3 Total Solids: 75 to 80 percent.2.7.6.1.4 Application Method: Spray.2.7.6.1.5 Application Method: Brush.2.7.6.1.6 Application Method: Roll.2.7.6.1.7 Elongation at 70 degree F (21 degree C): 850 percent minimum.2.7.6.1.8 Total Cure Time: 24 hours.

07 14 00-12

2.7.6.1.9 Tensile Strength (ASTM D 412): 32 psi (221 kPa).2.7.6.1.10 Weight/Gallon: 7.7 lb (3.5 kg).2.7.6.1.11 Coverage Rate: 2.5 to 3.5 gal/100 sf (0.9 to 1.2l/sm).2.7.6.1.12 Film Thickness, Dry: 60 mil (1.5 mm) minimum.2.7.6.1.13 Crack Bridging (ASTM C 836): 10 cycles without bond failure.2.7.6.1.14 Resistance to Water Flow (ASTM D 466): Bond strength not affected.2.7.6.1.15 Water Solubility (ASTM D 2939): No blistering or re-emulsion.2.7.6.1.16 Water Vapor (ASTM E 96):

2.7.6.1.16.1 Transmission: 0.12 grains/sf/h.2.7.6.1.16.2 Permeability: 0.28 perms (16 ng/(Pa X s X m2).

2.7.6.1.17 Resistance to Growth of Mold - Surface Disfigurement (ASTM D 3273, ASTM D 3274): None.

2.8 ACCESSORY MATERlALS

2.8.1 Provide accessory materials supplied by manufacturer, including the following:2.8.1.1 Mastic: Heavy bodied trowel grade coating of plastic or resin material

compatible with the waterproofing membrane. Color: Black. Consistency: Rubber coating.

2.8.1.1.1 Complies with ASTM D 4586 Type I and ASTM D 3409.2.8.1.1.2 Product: Mar-flex 362 Mastic as manufactured by Mar-flex Waterproofing

and Building Products.2.8.1.2 Drainage Clips Fasteners: Pronged clips to distribute weight of board to prevent

damage during backfill or fasteners to hold board in place until backfilled.2.8.1.2.1 Product: Mar-flex's Geo Clips as manufactured by Mar-flex Waterproofing

and Building Products.2.8.1.2.2 Product: Mar-flex Board Fasteners as manufactured by Mar-flex

Waterproofing and Building Products.

2.8.2 Above Grade Air/Vapor Waterproofing Accessories.2.8.2.1 Transition Strip: EcoFlash is a self adhering smooth surfaced modified bitumen

membrane. Nominal 40 mil thickness, multiple widths are available. Manufactured by Mar-flex Waterproofing and Building Products.

2.8.2.2 Transition Strip Primer: 1800 Primer for SB products or 1200 Primer for WB products. Both manufactured by Mar-flex Waterproofing and Building Products.

2.8.2.3 Substrate Filler: 1800 Mastic for SB products or 1200 Mastic for WB products. Both manufactured by Mar-flex Waterproofing and Building Products.

2.8.3 Horizontal Drainage Material:2.8.3.1 Mar-flex's 12 inches (305 mm) 522 DrainAway.2.8.3.2 Mar-flex's 12 inches (305 mm) Connectors.

2.8.4 Horizontal Drainage Material:2.8.4.1 Mar-flex's 6 inches (152 mm) 523 DrainAway.2.8.4.2 Mar-flex's 6 inches (152 mm) Connectors.

2.9 INSULATION/DRAINAGE BOARD

2.9.1 Product: Drain and Dry Insulation/Drainage Board:2.9.1.1 Material: Inorganic glass fiber.2.9.1.2 Thermal Resistance: 3.1 to 10.2.9.1.3 Foundation Drainage Rate: Up to 65 gal/hr/lin ft.

2.9.2 Product: ShockWave 1 or 2 Foundation Insulation/Drainage Board:2.9.2.1 Material: Closed cell foam board.2.9.2.2 Thermal Resistance: 9.0 to 13.50.2.9.2.3 Foundation Drainage Rate: Up to 101.11 gal/hr/lin ft.

07 14 00-13

2.9.3 Product: Geo-Mat Plus Drainage Roll:2.9.3.1 Material: High Density Polyethylene (HDPE) drainage rolls with attached

polypropylene geotextile mat.2.9.3.2 Foundation Drainage Rate: 30.1 gal/min/sf.

2.9.4 Product: Type I DrainCore Dimpleboard:2.9.4.1 Material: Polystyrene compressed into a light-duty dimpled core bonded to a

single layer of non-woven filter fabric.2.9.4.2 Foundation Drainage Rate: 9 gpm/ft width.

2.9.5 Product: Type II DrainCore Dimpleboard:2.9.5.1 Material: Polystyrene compressed into a moderate-duty dimpled core bonded to

a single layer of non-woven filter fabric.2.9.5.2 Foundation Drainage Rate: 21 gpm/ft width.

2.9.6 Product: ShockWave 1 or 2 Foundation Insulation/Drainage Board:2.9.6.1 Material: Closed cell foam board.2.9.6.2 Thermal Resistance: 9.0 to 13.50.2.9.6.3 Foundation Drainage Rate: Up to 101.11 gal/hr/lin ft

2.9.7 Product: Geo-Mat Plus Drainage Roll:2.9.7.1 Material: High Density Polyethylene (HDPE) drainage rolls with attached

polypropylene geotextile mat.2.9.7.2 Foundation Drainage Rate: 30.1 gal/min/sf.

2.9.8 Product: Type III DrainCore Decking Drainage:2.9.8.1 Material: Polystyrene compressed into a moderate-duty dimpled core bonded to

a single layer of non-woven filter fabric.2.9.8.2 Foundation Drainage Rate: 8.5 gpm/ft width.

3 EXECUTION

3.1 EXAMINATION

3.1.1 Do not begin installation until substrates have been properly prepared.

3.1.2 If substrate preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding.

3.2 PREPARATION

3.2.1 Clean and prepare substrate according to manufacturer's recommendations. Provide clean, dust-free, and dry substrate for waterproofing application.

3.2.2 Mask off adjoining surfaces not receiving waterproofing to prevent spillage or over spray affecting other construction.

3.2.3 Close off deck drains and other deck penetrations to prevent spillage and migration of waterproofing fluids.

3.2.4 Remove grease, oil, form release agents, paints, and other penetrating contaminants from concrete.

3.2.5 Remove fins, ridges, and other projections and fill honeycomb, aggregate pockets, grout joints, tie holes, and other voids with joint detailing mastic, hydraulic cement, or rapid-set grout.

3.2.6 Prepare and treat vertical and horizontal 90 degrees terminations, edge terminations,

07 14 00-14

penetrations through waterproofing material, expansion joints, cracks, drains, and sleeves according to ASTM C 898 and manufacturer's recommendations.

3.2.7 At each area to be treated, apply two coats of joint detailing mastic; embed joint reinforcing strip in first coat and apply second coat entirely covering the embedded joint reinforcing strip ensuring complete saturation.3.2.7.1 90 Degrees Terminations, Vertical and Horizontal: 6 inches (150 mm) on each

side.3.2.7.2 Penetrations, Drains, Sleeves: 6 inches (150 mm) radius around penetration and

3 inches (75 mm) onto penetrating object.3.2.7.3 Joints and Cracks: 6 inches (150 mm) wide on each side of joint/crack.

3.2.7.3.1 Remove dust and dirt from joints and cracks in accordance with ASTM D 4258 prior to coating surfaces.

3.2.7.3.2 Joints and Cracks Greater Than 1/16 inch (1.5 mm) In Width: Prior to applying joint detailing mastic, rout out joint/crack, install backer-rod and sealant to bring flush to surface.

3.2.8 Secure and protect plumbing, electrical, mechanical and structural items to be under or passing through waterproof membrane prior to membrane application.

3.2.9 When it is not possible to install waterproofing before placement of reinforcing steel, exposed reinforcing steel shall be masked by General Contractor prior to membrane application.

3.3 BELOW GRADE INSTALLATION

3.3.1 Install in accordance with manufacturer's instructions.

3.3.2 For vertical application apply a uniform coat of waterproofing to entire wall area. Obtain a seamless membrane free of entrapped gasses, with a minimum dry film thickness of 60 mil (1.5 mm) below-grade wall application.3.3.2.1 Apply fluid membrane onto footing area a minimum of 4 inches (102 mm) to

prevent water pooling.3.3.2.2 Allow membrane to cure for 24 hours before placing any backfill against the wall.3.3.2.3 Apply drainage board.3.3.2.4 Install DrainAway Vertical Collection System drainage.

3.3.3 For horizontal application apply a uniform coat of waterproofing to entire area. Obtain a seamless membrane free of entrapped gasses, with a minimum dry film thickness of 100 mil (2.5 mm) for above/at grade application.3.3.3.1 Allow the fluid membrane to cure out approximately 3 to 4 hours.3.3.3.2 Fluid membrane will still be tacky.3.3.3.3 Apply drainage board.3.3.3.4 Install DrainAway Vertical Collection System drainage.

3.4 BELOW GRADE INSTALLATION

3.4.1 Install in accordance with manufacturer's instructions.

3.4.2 For vertical application apply a uniform coat of waterproofing to entire wall area. Obtain a seamless membrane free of entrapped gasses, with a minimum dry film thickness of 80 mil (2 mm) at 10 feet (3.1 m) below-grade wall application, 100 mil (2.5 mm) at 20 feet (6.1 m) below-grade wall application and 120 mil (3 mm) at 30 feet (9.2 m) or more for below-grade wall application.3.4.2.1 Apply fluid membrane onto footing area a minimum of 4 inches (102 mm) to

prevent water pooling.3.4.2.2 Allow membrane to cure for 24 hours before placing any backfill against the wall.

07 14 00-15

3.4.3 For horizontal application apply a uniform coat of waterproofing to entire wall area. Obtain a seamless membrane free of entrapped gasses, with a minimum dry film thickness of 100 mil (2.5 mm) for above/at grade application.3.4.3.1 Allow the fluid membrane to cure out approximately 3 to 4 hours.3.4.3.2 Fluid membrane will still be tacky.3.4.3.3 Apply drainage board.3.4.3.4 Install DrainAway Vertical Collection System drainage.

3.5 INSULATING/DRAINAGE PANEL INSTALLATION

3.5.1 Drain and Dry: Begin installation of panels after membrane has been applied. Place and secure drainage panels to substrate according to manufacturer's current written instructions.3.5.1.1 Install panels from top of footing extending to finish grade level. When Drain and

Dry is to be stacked, maintain a factory-equivalent edge at all seams to ensure proper fit and drainage channel alignment.

3.5.1.2 Secure Drain and Dry to the wall using powder actuated mechanical fasteners. Install top fasteners within 4 inches (102 mm) of the tops of each panel.

3.5.1.3 If the board overlaps the membrane at the grade line, a utility knife or similar tool can be used to cut the boards to the correct height.

3.5.2 Geo-Mat Plus: Install after membrane has been applied. Place and secure to substrate according to manufacturer's current written instructions.3.5.2.1 While the membrane is still tacky, begin installation at a corner. Install

horizontally against the waterproofing membrane with the polypropylene geotextile mat side facing out-ward.

3.5.2.2 Install panels from top of footing extending to finish grade level.3.5.2.3 For good adherence, apply uniform pressure throughout the surface area, not

just the edges and corners.3.5.2.4 When two edges come together from two separate pieces, overlap the dimples

and seal with an adhesive band such as the Eco-Flash to create continuous coverage of the wall.

3.5.2.5 Secure the Geo-Mat Plus to the wall with Geo-Mat accessories.3.5.2.6 If the board overlaps the membrane at the grade line, a utility knife or similar tool

can be used to cut the boards to the correct height.

3.5.3 ShockWave: Install after membrane has been applied. Place and secure to substrate according to manufacturer's current written instructions.3.5.3.1 While the membrane is still tacky, starting at a corner with the filter fabric side

facing out-ward, install the ShockWave Drainage Board horizontally over the sprayed sections of the wall. The boards shall be placed side by side, extending from the top of the footing to finished grade.

3.5.3.2 Apply uniform pressure to the board throughout the surface area, not just the edges and corners. Note: If boards are stacked, maintain a factory-equivalent edge at all seams to ensure proper fit and drainage channel alignment. Using a Geo Clip, secure the ShockWave to the wall at corners and seems.

3.5.3.3 The use of fasteners, such as concrete nails or Mar-flex Geo Clips, to secure the board to the walls to hold in place until backfilled is optional

3.5.3.4 If using the Geo Clip, secure the ShockWave to the wall at corners and seems.3.5.3.5 When securing the ShockWave at the top of the boards, place a Geo Clip at

each corner making sure that at least two prongs from the Geo Clip is placed in each board.

3.5.3.6 Once the Geo Clips are in place install them using a powder actuated mechanical fastener or concrete nail.

3.5.3.7 If the board overlaps the membrane at the grade line, a utility knife or similar tool can be used to cut the boards to the correct height.

3.5.4 Type I or Type II: Install after membrane has been applied. Place and secure to substrate

07 14 00-16

according to manufacturer's current written instructions.3.5.4.1 While the membrane is still tacky, begin installation at a corner. Install

horizontally against the waterproofing membrane with the non-woven filter fabric side facing out-ward.

3.5.4.2 Install panels from top of footing extending to finish grade level.3.5.4.3 For good adherence, apply uniform pressure throughout the surface area, not

just the edges and corners.3.5.4.4 When two edges come together from two separate pieces, overlap the dimples

and apply an adhesive band to create continuous coverage of the wall.3.5.4.5 If needed, secure the panels to the wall using a powder actuated mechanical

fastener or concrete nail.3.5.4.6 If the board overlaps the membrane at the grade line, a utility knife or similar tool

can be used to cute the boards to the correct height.

3.5.5 Type III: For flat decking, begin installation after membrane has been applied. Place draincore to substrate according to manufacturer's current written instructions.3.5.5.1 Unroll the Type III, placing gray side down against membrane. To keep in place,

use double sided tape, adhesives or nails.3.5.5.2 For overlaps, place adjacent sections so that the cores abut. Secure fabric

overlap at five foot intervals with glue, tape or nails.3.5.5.3 Join roll ends by peeling back fabric and removing 4 inches of core. Place end

panels so that cores abut, then glue, tape or nail fabric overlap with no more than a 1/4 inch (6 mm) gap to prevents concrete or any debris from entering water flow channels.

3.5.5.4 Make cuts for any drains to allow water to be drained.3.5.5.5 Allow 24 hour set time.3.5.5.6 Pour desired thickness of concrete over the Type III.

3.5.6 Protect installed insulation/drainage panels during subsequent construction.

3.5.7 Backfill and Drainage:3.5.7.1 #57 Gravel or equivalent must go no less than 2 feet (610 mm) high at the base

of the foundation and 1 feet (305 mm) in depth out from the foundation walls.3.5.7.2 Adequate interior and exterior foundation drainage at the base of the foundation

walls, across any floors or adjacent flower beds must be properly installed and functioning properly.

3.5.7.3 Backfilling should begin no sooner than 24 hours after the installation of the board, but shall be backfilled within 15 days.

3.5.8 DrainAway Vertical Collection System Installation:3.5.8.1 Unroll material along foundation base in 50 foot (15.25 m) sections; adhere to

partially cured waterproofing material; use adhesive acceptable to waterproofing material manufacturer for cured waterproofing or other sheet waterproofing not requiring curing.

3.5.8.2 Install preformed corner fittings at foundation interior and exterior corners. Install outlet fittings where indicated; connect to corrugated drainage pipe if present at time of modular system installation; leave ready for connection to corrugated drainage pipe if not present.

3.6 ABOVE GRADE AIR/VAPOR BARRIER INSTALLATION

3.6.1 Install materials in accordance with manufacturer's instructions.

3.6.2 Air and Vapor Barrier 1800: Apply at a rate of 30 sf/gal, providing a seamless monolithic coverage with a final thickness of 40 mils dry.

3.6.3 Air Barrier 1200 VP: Apply at a rate of 30 sf/gal, providing a seamless monolithic coverage

07 14 00-17

with a final thickness of 40 mils dry.

3.6.4 Transition joint primer: Apply 1800 (SB) or 1200 (WB) primer to all areas receiving the transition strip.

3.6.5 Transition joints: Seal with EcoFlash transition strip at beams, columns, changes in substrate material and similar joints or connections to provide continuity of air/vapor barrier assembly. Generally, apply transition strip so that a minimum of 3 inches (76 mm) coverage is achieved over both substrates. Position strip over firm bearing.

3.6.6 Window frame perimeter and door frames: Lap transition strip from wall substrate with a minimum of 3 inches (76 mm) of full contact over form bearing to window or door frame with 1 inch (25 mm) of full contact.

3.6.7 Apply air/vapor barrier membrane within recommended application temperature ranges. Consult manufacturer when membrane cannot be applied within these temperature ranges.

3.6.8 Using airless spray equipment with a minimum pressure of 3000 psi, apply first coat of air barrier membrane over exterior face of the inner cavity wall.

3.6.9 Use alternating horizontal and vertical passes to ensure complete coverage of substrate and transition strips. Seal masonry anchors or other penetrations air tight.

3.6.10 Check surface again and if necessary, fill any remaining gaps with mastic substrate filler prior to covering with membrane.

3.6.11 Complete application of membrane at a coverage rate of 20-25 sf /gal, to provide a seamless monolithic surface to a thickness of 40 mils (1 mm).

3.6.12 Inspect surface area with wet mil gauge to ensure proper thickness.

3.6.13 Allow 12-24 hours for membrane to fully cure.

3.7 PROTECTION

3.7.1 Protect installed products until completion of project.

3.7.2 Touch-up, repair or replace damaged products before Substantial Completion.

END OF SECTION

07 14 00-18