ARGtek ARG-1210 QIG

7/28/2019 ARGtek ARG-1210 QIG

1/18

ARGtek Communication Inc. www.argtek.comE-Mail:[email protected] Tel:+ 886-2-2999-6958 Fax :+ 886-2-2999-7742

ARGtek ARG-1210 WLAN AP RouterFor 802.11b/g/n

POWER KING-X

Quick Installation Guide

Ver. 08.11


2/18


Part I: External Installation Direction

Package Content

AP Router 1

DC 12V Power Adapter 1

Antenna 2

PoE DC Injector 1

Paper QIG 1

Manual/QIG CD 1

AP Router Connection

Before installing the router, please connect your PC to the internet through your internet

service provider.


3/18


1. Turn off your PC(s), cable/ ADSL modem and the router.2. Adjust the antenna if needed. Normally, straight up on router is good.3. Connect the PC(s) and each switch/hub on your local area network to the LAN ports on

the router.4. Connect the ADSL/DSL/cable modem to the router WAN port.5. Connect the power adapter between the DC-Jack on the router and an electrical outlet.

The router will start to work automatically.6. Turn on your PC(s) and the cable/ADSL modem.

.

The front LED indicators


4/18


AP Router configuration

The AP Router is delivered with the following factory default parameters on the Ethernet LANinterfaces.

Default IP Address: 192.168.1.254Default IP subnet mask: 255.255.255.0Web login User Name: Web login Password:

The device has three operation modes:1, Gateway2, Bridge3, WISPThe default IP addresses for the device are 192.168.1.254, and you need to make sure the IPaddress of your PC is in the same subnet as the device, such as 192.168.1.X.It will take about 55 seconds to complete the boot up sequence after power on.


5/18


PoE DC Injector Configuration

PPOE stands for Power over Ethernet, and it is usually used with Wireless Device.You can use it to integrate the power and the Ethernet then connected with the RJ45 cable.With POE, you can bring the power and Ethernet together in one cable for long distance asfar as the RJ45 cable can reach.

Part II: Internal Web Management


6/18


1, Gateway: AP Mode Setup (ADSL)

1-1. Install the antenna & power adapter, and then connect the LAN cable with LAN port ofthis equipment. Another side of cable line connects with network card of computer. Pleasewait for reboot around 20 seconds.

1-2. Open the IE (or other browser) and type http://192.168.1.254 on URL to enter the setupframe. If you cant enter to setup frame, please press Reset button around 10 seconds torestore AP and try to enter again.

1-3. Select the Setup Wizard on the left side of setup frame and press Next>>

1-4. In Operation Mode, select Gateway and press Next>>


7/18


1-5. In Time Zone Setting, if you dont need any change, please press Next>>

1-6. In LAN Interface Setup, you may change the setting of IP address, DHCP and etc.

Then press Next>>

1-7. In WAN Interface Setup, select PPPoE Client for your connection of WAN Access Type

and press Next>>


8/18


1-8. In Wireless Basic Setting, select AP Mode and change your SSID name,

then press Next>>

1-9. In Wireless Security, select your setup of wireless security (WEP, WPA) and press

Finished to reboot, and wait for 20 seconds for reboot.


9/18


Note: You have to connect ADSL cable with WAN port on Gateway Mode

2. AP Mode Setup (IP Share)


10/18


2-1. Install the antenna & power adapter, and then connect the LAN cable with LAN port ofthis equipment. Another side of cable line connects with network card of computer. Waiting forreboot around 20 seconds.

2-2. Open the IE (or other browser) and type http://192.168.1.254 on URL to enter the setup

frame. If you cant enter to setup frame, please press Reset button around 10 seconds torestore AP and try to enter again.2-3. Select the Setup Wizard on the left side of setup frame and press Next>>

2-4 . In Operation Mode, select Bridge and press Next>>


11/18



2-6. In LAN Interface Setup, you may change the setting of IP address, DHCP and etc. then

press Next>>


12/18


2-7. In WAN Interface Setup, select DHCP Client for your connection of WAN Access Type

and press Next>>

2-8. In Wireless Basic Setting, select AP for your Mode and change your SSID setup, then

press Next>>


13/18


2-9. In Wireless Security, select your setup of wireless security (WEP, WPA) and press

Finished to reboot, and wait for 20 seconds for reboot.

2-10. Select the TCP/IP Settings from left side of setup frame and choice LAN Interface.

Then choosing Disable from DHCP and press Apply Changes to reboot around 20 seconds to

complete the setup.


14/18


Note: Please connect cable line with LAN port when you use Bridge Mode to connect

IP Share.


15/18


3. WISP Mode Setup (IP Share)

3-1. Install the antenna & power adapter, and then connect the LAN cable with LAN port ofthis equipment. Another side of cable line connects with network card of computer. Pleasewait for reboot around 20 seconds.

3-2. Open the IE (or other browser) and type http://192.168.1.254 on URL to enter the setupframe. If you cant enter to setup frame, please press Reset button around 10 seconds torestore AP and try to enter again.3-3. Select the Setup Wizard on the left side of setup frame and press Next>>

3-4. In Operation Mode, select Wireless ISP and press Next>>


16/18



3-6. In LAN Interface Setup, you may change the setting of IP address, DHCP and etc. then

press Next>>


17/18


3-7. In WAN Interface Setup, select PPPoE for your connection of WAN Access Type and

enter User Name & Password which presented by your ISOP. And then press Next>>

Note: Connecting Telecom Access Point usually is based on PPPoE, but in general, a pureconnection is via Static IP or DHCP

Client.


18/18

ARGt k C i ti I t k

3-8. In Wireless Basic Setting, select Client for your Mode and change your SSID setup, then

press Next>>

3-9. In Wireless Security, select your setup of wireless security (WPA) and press Finished to

reboot around 20 seconds, and wait for 20 seconds for reboot.

Note: Please connect cable line with LAN port when you use WISP Mode.

Documents

ARGtek ARG-1210 QIG