VICTORIA Phone: (61 3) 9587 7700 Facsimile: (61 3) 9587 7711 NEW SOUTH WALES Phone: (61 2) 9791 1011 Facsimile: (61 2) 9791 1022 QUEENSLAND Phone: (61 7) 3272 7500 Facsimile: (61 7) 3272 7505 SOUTH AUSTRALIA Phone: (61 8) 8297 1722 Facsimile: (61 8) 8297 1733 www.hales.com.au Toll Free: 1300 660 854 Sintered Vents Used for Blow Moulding, Diecasting or Vacuum Casting Pore Diameter: 0.30mm Product Code 30510 30610 30615 30810 30815 31010 31015 31210 31215 31415 Diameter 5 6 6 8 8 10 10 12 12 14 No. of Pores 89 89 89 200 200 340 340 340 340 550 Length 10 10 15 10 15 10 15 10 15 15 Used for Plastic Injection Moulding Pore Diameter: 0.03 ~ 0.10mm Product Code SV030410 SV030610 SV030810 SV031010 SV050610 SV050810 SV051010 SV100810 SV101010 Outer Diameter 4 6 8 10 6 8 10 8 10 Eff. Diameter 2.5 2.5 2.5 2.5 3.5 3.5 3.5 5.5 5.5 No. of Pores 880 880 880 880 880 880 880 880 880 Length 10 10 10 10 10 10 10 10 10 Length Diameter Length Diameter Effective Diameter The pores allow trapped air or gas to escape from the mould cavity during the injection moulding or die casting process, thereby reducing the occurrence of defective parts. Pore diameter Pore diameter SINTERED VENTS Assists with purging air and gas during the moulding process. Insulation Sheet • Machined to suit your application. • Polyester glass laminate. • Low thermal conductivity continuous to 220C. Standard sheet also available. • 0.8-50mm thick available. Also Available at Hales Countersink holes Location ring cut out Cap screw clearance hole Contact Hales on [email protected] or call 1300 660 854 for more information

Assists with purging air and gas during the moulding process. · 2016-06-29 · The pores allow trapped air or gas to escape from the mould cavity during the injection moulding or

Download PDF Report

Upload
others
View
3
Download
0

Embed Size (px)

Citation preview

Page 1: Assists with purging air and gas during the moulding process. · 2016-06-29 · The pores allow trapped air or gas to escape from the mould cavity during the injection moulding or

VICTORIAPhone: (61 3) 9587 7700Facsimile: (61 3) 9587 7711

NEW SOUTH WALESPhone: (61 2) 9791 1011Facsimile: (61 2) 9791 1022

QUEENSLANDPhone: (61 7) 3272 7500Facsimile: (61 7) 3272 7505

SOUTH AUSTRALIAPhone: (61 8) 8297 1722Facsimile: (61 8) 8297 1733

www.hales.com.au

Toll Free: 1300 660 854

Sintered Vents

Used for Blow Moulding, Diecastingor Vacuum CastingPore Diameter: 0.30mm

Product Code 30510 30610 30615 30810 30815 31010 31015 31210 31215 31415

Diameter 5 6 6 8 8 10 10 12 12 14

No. of Pores 89 89 89 200 200 340 340 340 340 550

Length 10 10 15 10 15 10 15 10 15 15

Used for Plastic Injection MouldingPore Diameter: 0.03 ~ 0.10mm

Product Code SV030410 SV030610 SV030810 SV031010 SV050610 SV050810 SV051010 SV100810 SV101010

Outer Diameter 4 6 8 10 6 8 10 8 10

Eff. Diameter 2.5 2.5 2.5 2.5 3.5 3.5 3.5 5.5 5.5

No. of Pores 880 880 880 880 880 880 880 880 880

Length 10 10 10 10 10 10 10 10 10

Length

Diameter

Length

Diameter EffectiveDiameter

The pores allow trapped air or gas to escape from the mould cavity during the injection moulding or die casting process, thereby reducing the occurrence of defective parts.

Pore diameter

SINTERED VENTSAssists with purging air and gasduring the moulding process.

Insulation Sheet• Machined to suit your application.

• Polyester glass laminate.

• Low thermal conductivity continuous to 220C. Standard sheet also available.

• 0.8-50mm thick available.

Also Available at Hales

Countersink holes

Location ring cut out

Cap screw clearance hole

Contact Hales on [email protected] or call 1300 660 854 for more information