AUTOMATIC AND TRANSFER SWITCH PANELS · amf automatic mains failure panels ats automatic transfer ... bottom cap for wiring inlet. single-line diagram and ... amf-0050/2 50 6 11,5

CATALOGUE

ENwww.inmesol.com

AUTOMATIC AND TRANSFER SWITCH PANELS*

2 These details shown on this data sheet are intended for guidance only. Inmesol reserves the right to change the details without prior notice. The present documents will not be part of any sales contract. Prices provided are correct unless there might have been a mistake or we drop any product from our product range.

Rev. 02 | 17/10/2018

DESIGNED AND MANUFACTURED BY INMESOLAll the engineering, design, and manufacture processes are performed in our facilities.

3These details shown on this data sheet are intended for guidance only. Inmesol reserves the right to change the details without prior notice. The present documents will not be part of any sales contract. Prices provided are correct unless there might have been a mistake or we drop any product from our product range.

Rev. 02 | 17/10/2018

This catalogue is a guide to select the electrical panel for your generator set according to its power and purpose.

It shows a report with several panels within the wide range of products offered by INMESOL to meet any electrical requirement.

You will find here the perfect match for your generator set.

Certificate of Electromagnetic Compatibility (UE/2014/30/ Directive) and Low Voltage (UE/2014/35/ Directive)

We manufacture the equipment and technology the

market demands at any time.

CONTENTS:

LTS LOAD TRANSFER SWITCH PANELS*

AMF AUTOMATIC MAINS FAILURE PANELS

ATS AUTOMATIC TRANSFER SWITCH PANELS

APP PARALLEL APPLICATIONS

APPLICATION EXAMPLES

CONTROL UNITS

OP OPTIONAL FEATURES AND ACCESSORIES

*Automatic switch or transfer between the mains and the generator set/power generation system.


GENSET WITH AMF CONTROL PANEL WHITOUT TRANSFER SWITCH. READY TO ADD SEPARATED LTS PANEL.

Rev. 02 | 17/10/2018

LOAD TRANSFER SWITCH PANELSLTS

DESCRIPTIONControl panel offered in a metal cabinet with an IP-67 protection grade with the following elements:

1. Two contactors or a motor-driven selector, equipped with mechanical and electrical interlock, preventing them from being closed simultaneously, thus avoiding potential short circuits.

2. Protection fuses.

3. Terminal block for the connection of control signals from the generator set.

4. Terminal block for the connection of the input power cables from the generator set, network input and load output.

5. Connection wiring of all the panel’s electrical items. Each wire is identified with its reference number in each end.

6. Emergency shutdown pushbutton.

7. Front door with lock.

8. Bottom entrance for wiring inlet.

Note.- All panels are protected against direct contact with live parts when the door is open.

SINGLE-LINE DIAGRAM AND CONNECTIONS

LOAD

LTS

GENERATOR SET

G

MAINS

TDSE 6120 MKII

-DSE 7320 MKII

-SIMILAR

FUNCTIONALITYIt enables a change in the power supply (supplying the load of a facility) between the mains and the generator set.

The transfer switch is formed by two contactors or motor-driven selectors equipped with MECHANICAL AND ELECTRICAL INTER-LOCK.

The operation is controlled from the switchboard mounted in the generator set, type DSE 6120 MKII, DSE 7320 MKII (INMESOL V3 version) or similar.

This panel is suitable for any generator set featuring a control module with AMF (AUTOMATIC MAINS FAILURE) function.

6

73

8

1

4

5

2

6

Wall panel

Floor panel


Rev. 02 | 17/10/2018

50 Hz

LOAD TRANSFER SWITCH PANELS

LTS-0050/2 50 6 11,5 C ABB AF09 - 2 400x400x210 15 W

LTS-0060/2 60 7,2 13,8 C ABB AF16 - 2 400x400x210 15 W

LTS-0090/2 90 11 21 C ABB AF26 - 2 400x400x210 15 W

LTS-0120/2 120 14 28 C TERASAKI TC40A/4 - 2 400x400x210 15 W

LTS-0200/2 200 24 46 C ABB AF52 - 2 700x500x260 30 W

LTS-0250/2 250 30 58 C ABB AF80 - 2 700x500x260 30 W

LTS-0320/2 320 38 74 MCOS SOCOMEC ATySM3S - 2 700x500x260 35 W


LTS-0025/3 25 10 6 C ABB AF09 - 3 400x400x210 15 W

LTS-0030/3 30 12 7 C ABB AF16 - 3 400x400x210 15 W

LTS-0045/3 45 18 11 C ABB AF26 - 3 400x400x210 15 W


LTS-0100/3 100 40 24 C ABB AF52 - 3 700x500x260 30 W

LTS-0125/3 125 50 30 C ABB AF80 - 3 700x500x260 30 W

LTS-0160/3 160 64 38 MCOS SOCOMEC ATySM3S - 3 700x500x260 35 W


LTS-0400/3 400 159 96 MCOS ABB OTM400 - 3 1000x800x400 80 W

LTS-0630/3 630 251 151 MCOS ABB OTM630 - 3 1700x800x500 160 S







LTS-0025/4 25 9 17 21 C ABB AF09 - 4 400x400x210 15 W

LTS-0030/4 30 11 21 25 C ABB AF16 - 4 400x400x210 15 W

LTS-0045/4 45 16 31 37 C ABB AF26 - 4 400x400x210 15 W

LTS-0060/4 60 22 42 50 C TERASAKI TC40A/4 - 4 400x400x210 15 W

LTS-0100/4 100 36 69 83 C ABB AF52 - 4 700x500x260 30 W

LTS-0125/4 125 45 87 104 C ABB AF80 - 4 700x500x260 30 W

LTS-0160/4 160 58 111 133 MCOS SOCOMEC ATySM3S - 4 700x500x260 35 W

LTS-0260/4 260 94 180 216 C TERASAKI TC225A/4 - 4 800x600x300 55 W

LTS-0400/4 400 144 277 332 MCOS ABB OTM400 - 4 1000x800x400 80 W

LTS-0630/4 630 227 436 523 MCOS ABB OTM630 - 4 1700x800x500 160 S







SINGLE-PHASE

TWO-PHASE or 3 x 230 V (W/O NEUTRAL)

THREE-PHASE

LTS

MODEL AMPPOWER (kvA) PRP TRANSFER

SWITCH*BRAND TYPE UNIT CONTROL POLES

DIMENSIONS (mm)

HEIGHTxWIDTHxDEPTHWEIGHT

(Kg)ASSEM-

BLY@ 120/240 V @ 3 x 230 V



DIMENSIONS (mm)


(Kg)ASSEM-

BLY@ 1 x 120 V @ 1 x 230 V

MODEL AMPPOWER (kvA) PRP TRANS-

FER SWITCH*

BRAND TYPE UNIT CONTROL POLES

DIMENSIONS (mm)


(Kg)ASSEM-

BLY@ 3 x 208 V @ 3 x 400 V @ 3 x 480 V

Transfer Switch: C: Contactors. MCOS: Motor-driven selector. MCB: Motor-driven circuit breaker.Assembly: W: Wall. S: Floor


GENSET WITH AMF CONTROL PANEL WITH TRANSFER SWITCH.

PREWIRED GENSET READY TO INSTALL AMF CONTROL PANEL.

Rev. 02 | 17/10/2018

AUTOMATIC MAINS FAILURE PANELSAMF




3. Terminal block for control and operation of the generator set.

4. Terminal block for connection of the generator set input power cables, network input, and load output.


6. Battery charger.

7. Input terminal block for battery charger

8. Transformers


10. Control switchboard (DSE 6120 MKII, DSE 7320 MKII or similar)

11. Ignition key (for switchboard supply)

12. Alarm.


14. Bottom cap for wiring inlet.


FUNCTIONALITYThis panel has a control and command switchboard type DSE 6120 MKII, DSE 7320 MKII (INMESOL V2 version) or similar that detects when a mains failure occurs and enables the change of power supply (supplying the load of a facility) between the mains and the generator set and vice versa when the mains are restored.

The transfer switch is formed by two contactors or motor-driven selectors equipped with MECHANICAL AND ELECTRICAL INTERLOCK.

In this case, the generator set does NOT need a control switchboard; this applies to any predisposed genset (INMESOL V1 version) or similar.

610

8 12

13

9

3 7

14

10

11

13

12

9

1

4

5

2

GT

MAINS

DSE 6120 MKII-

DSE 7320 MKII

AMF

GENERATOR SET

LOAD

Wall panel

Floor panel


Rev. 02 | 17/10/2018

AUTOMATIC MAINS FAILURE PANELSAMF

50 Hz

AMF-0050/2 50 6 11,5 C ABB AF09 DSE 6120 MKII 2 500x400x210 20 W

AMF-0060/2 60 7,2 13,8 C ABB AF16 DSE 6120 MKII 2 600x400x260 25 W

AMF-0090/2 90 11 21 C ABB AF26 DSE 6120 MKII 2 600x400x260 25 W

AMF-0120/2 120 14 28 C TERASAKI TC40A/4 DSE 6120 MKII 2 600x400x260 25 W



AMF-0320/2 320 38 74 MCOS SOCOMEC ATySM3S DSE 6120 MKII 2 700x500x260 35 W








AMF-0160/3 160 64 38 MCOS SOCOMEC ATySM3S DSE 6120 MKII 3 700x500x260 35 W


AMF-0400/3 400 159 96 MCOS ABB OTM400 DSE 7320 MKII 3 1700x600x400 125 S








AMF-0025/4 25 9 17 21 C ABB AF09 DSE 6120 MKII 4 500x400x210 20 W



AMF-0060/4 60 22 42 50 C TERASAKI TC40A/4 DSE 6120 MKII 4 600x400x260 25 W



AMF-0160/4 160 58 111 133 MCOS SOCOMEC ATySM3S DSE 6120 MKII 4 700x500x260 35 W

AMF-0260/4 260 94 180 216 C TERASAKI TC225A/4 DSE 6120 MKII 4 1200x600x300 80 W

AMF-0400/4 400 144 277 332 MCOS ABB OTM400 DSE 7320 MKII 4 1700x600x400 125 S








SINGLE-PHASE


THREE-PHASE




DIMENSIONS (mm)


(Kg)ASSEM-

BLY@ 120/240 V @ 3 x 230 V



DIMENSIONS (mm)


(Kg)ASSEM-

BLY@ 1 x 120 V @ 1 x 230 V


FER SWITCH*

BRAND TYPE UNIT CONTROL POLESDIMENSIONS (mm)


(Kg)

AS-SEM-BLY@ 3 x 208 V @ 3 x 400 V @ 3 x 480 V


Rev. 02 | 17/10/2018

AUTOMATIC TRANSFER SWITCH PANELSATS

DSE 334

LOAD

ATS

GENERATOR SET

G

MAINS

TDSE 3110

-DSE 7310 MKII

-DSE 6110 MKII

-SIMILAR




3. Terminal block for control and operation of the generator set.

4. Terminal block for connection of the generator set input power cables, network input, and load output.


6. Battery charger

7. Transformers


9. Ignition key (for switchboard supply)

10. DSE 334 Switchboard


12. Bottom cap for wiring inlet.


FUNCTIONALITYThis panel has a switchboard type DSE 334 that detects when a mains failure occurs and sends a start-up signal to the switchboard type DSE 3110, DSE 6110 MKII, DSE 7310 MKII or similar on the genset.

Once turned on and ready, the DSE 334 panel switchboard operates to enable the change of power supply (supplying the load of a facility) between the mains and the generator set and vice versa when the mains are restored.

The transfer switch is formed by two contactors or motor-driven selectors equipped with MECHANICAL AND ELECTRICAL INTER-LOCK.

This panel applies to any generator set featuring any switchboard with remote control / start-up by signal feature.

7

8

8

9

9

3

11

12

4

1

2

5

6

10

10

Wall panel

Wall panel


Rev. 02 | 17/10/2018

AUTOMATIC TRANSFER SWITCH PANELSATS

50 Hz

ATS3-0050/2 50 6 11,5 C ABB AF09 DSE 334 2 500x400x210 20 W

ATS3-0060/2 60 7,2 13,8 C ABB AF16 DSE 334 2 600x400x260 25 W

ATS3-0090/2 90 11 21 C ABB AF26 DSE 334 2 600x400x260 25 W

ATS3-0120/2 120 14 28 C TERASAKI TC40A/4 DSE 334 2 600x400x260 25 W



ATS3-0320/2 320 38 74 MCOS SOCOMEC ATySM3S DSE 334 2 700x500x260 35 W








ATS3-0160/3 160 64 38 MCOS SOCOMEC ATySM3S DSE 334 3 700x500x260 35 W


ATS3-0400/3 400 159 96 MCOS ABB OTM400 DSE 334 3 1700x600x400 125 S








ATS3-0025/4 25 9 17 21 C ABB AF09 DSE 334 4 500x400x210 20 W



ATS3-0060/4 60 22 42 50 C TERASAKI TC40A/4 DSE 334 4 600x400x260 25 W



ATS3-0160/4 160 58 111 133 MCOS SOCOMEC ATySM3S DSE 334 4 700x500x260 35 W


ATS3-0400/4 400 144 277 332 MCOS ABB OTM400 DSE 334 4 1700x600x400 125 S








SINGLE-PHASE


THREE-PHASE




DIMENSIONS (mm)


(Kg)ASSEM-

BLY@ 120/240 V @ 3 x 230 V



DIMENSIONS (mm)


(Kg)ASSEM-

BLY@ 1 x 120 V @ 1 x 230 V


FER SWITCH*



(Kg)

AS-SEM-BLY@ 3 x 208 V @ 3 x 400 V @ 3 x 480 V


Rev. 02 | 17/10/2018

LOAD TRANSFER SWITCH PANEL, PARALLEL WITH THE MAINS (1 GENSET)LTSP

LTSP-0150/4 150 54 104 125 C TERASAKI TC100A/4 - 4 800x600x300 75 W




LTSP-0660/4 660 238 457 548 C TERASAKI TC630A/4 - 4 1700x1000x400 230 S

LTSP-1000/4 1000 360 692 830 C GE CK1000A - 4 1700x1000x400 210 S

LTSP-1250/4 1250 450 865 1038 MCB ABB T7S1250 - 4 1700x1000x400 200 S

LTSP-1600/4 1600 576 1107 1328 MCB ABB T7S1600 - 4 1700x1000x400 200 S

LTSP-2000/4 2000 720 1384 1660 MCB ABB E2.2B2000 - 4 1700x1800x800 505 S

LTSP-2500/4 2500 900 1730 2075 MCB ABB E2.2N2500 - 4 1700x1800x800 545 S

LTSP-3200/4 3200 1152 2214 2656 MCB ABB E4.2N3200 - 4 1700x2200x600 545 S


PARALLEL OPERATIONSAPP


Parallel generator sets installations enable the supply of high amounts of power depending on the needs, both as the main supply or in case of emergency.

When the power supply in an emergency genset remains synchronised with the mains for a few seconds after power has been restored after a failure it is also considered as a parallel installation.


1 DESCRIPTIONPanel offered in a metal cabinet with an IP-67 protection level, featuring the same items as the LTF panel, except that the transfer switch consists of two contactors or motor-driven circuit breakers WITHOUT INTERLOCK 1


FER SWITCH*



(Kg)

AS-SEM-BLY@ 3 x 208 V @ 3 x 400 V @ 3 x 480 V

Wall panel

FUNCTIONALITYIt enables the change of power supply (supplying the load of a facility) between the mains and the generator set, and vice versa when the mains are restored.

The transfer switch is formed by two contactors or two motor-driven circuit breakers (in both cases, WITHOUT MECHANICAL INTERLOCK), that enable the synchronisation between the mains and the genset when the mains are restored.

This operation comes from the switchboard installed in the generator set, type DSE 8620, DEIF, COMAP, or similar.

The load does not suffer any power loss when the mains is restored.

LOAD

LTSP

GENERATOR SET

G

MAINS

TDSE 8620

-DEIF

-COMAP

-SIMILAR


PREWIRED GENSET READY TO INSTALL AMF CONTROL PANEL.

Rev. 02 | 17/10/2018

AMFP-0150/4 150 54 104 125 C TERASAKI TC100A/4 DSE 8620 4 1200x600x300 75 W




AMFP-0660/4 660 238 457 548 C TERASAKI TC630A/4 DSE 8620 4 1700x1000x400 230 S

AMFP-1000/4 1000 360 692 830 C GE CK1000A DSE 8620 4 1700x1000x400 210 S

AMFP-1250/4 1250 450 865 1038 MCB ABB T7S1250 DSE 8620 4 1700x1000x400 200 S

AMFP-1600/4 1600 576 1107 1328 MCB ABB T7S1600 DSE 8620 4 1700x1000x400 200 S

AMFP-2000/4 2000 720 1384 1660 MCB ABB E2.2B2000 DSE 8620 4 1700x1800x800 505 S

AMFP-2500/4 2500 900 1730 2075 MCB ABB E2.2N2500 DSE 8620 4 1700x1800x800 545 S

AMFP-3200/4 3200 1152 2214 2656 MCB ABB E4.2N3200 DSE 8620 4 1700x2200x600 545 S



AUTOMATIC TRANSFER SWITCH PANEL PARALLEL WITH THE MAINS (1 GENSET)AMFP


1

DESCRIPTIONPanel offered in a metal cabinet with an IP-67 protection level, featuring the same items as the AMF panel, except that the transfer switch consists of two contactors or two motor-driven circuit breakers WITHOUT INTERLOCK 1 and the INSTALLED control switchboard on the panel is the DSE 8620 or similar.


FER SWITCH*



(Kg)

AS-SEM-BLY@ 3 x 208 V @ 3 x 400 V @ 3 x 480 V

FUNCTIONALITYThis panel has a control and command switchboard type DSE 8620, DEIF, COMAP or similar that enables the change of power supply (supplying the load of a facility) between the mains and the generator set and vice versa when the mains are restored.

The transfer switch is formed by two contactors or two motor-driven circuit breakers (in both cases, WITHOUT MECHANICAL INTERLOCK), that enable the synchronisation between the mains and the genset when the mains are restored.

The load does not suffer any power loss when the mains is restored.

GT

MAINS

AMFP

GENERATOR SET

LOAD

Wall panel

DSE 8620-

DEIF-

COMAP-

SIMILAR


Rev. 02 | 17/10/2018



ATS8-0160/4 160 58 111 133 MCOS SOCOMEC ATySM3S DSE 8660 4 700x500x260 35 W











ATS8 AUTOMATIC TRANSFER SWITCH PANEL NOT PARALLEL WITH THE MAINS (2 GENSETS OR MORE)

FUNCTIONALITYThis panel has a switchboard type DSE 8660 MKII or similar that detects when a mains failure occurs and sends a start-up signal to the switchboard type DSE 8610 MKII, DEIF COMAP or similar on each of the gensets that make up the parallel system (2 or more gensets). Once started and synchronised, the panel switchboard sends commands opening and closing contactors / motor-driven selectors (with interlock) to change the network supply to the generator

set.

When the mains are restored, the switchboard operates to enable the change of supply from the generator sets to the mains (not synchronised) and afterward it sends signals to the generator set switchboards (DSE 8610 MKII or similar) to stop the engines.

The generator sets work in sync with each other and in stand-by with the mains, but are not synchronised with the mains.


DESCRIPTION

DSE 8660 MKII-

SIMILAR

LOAD

GENERATOR SET 2GENERATOR SET 1

G2G1

MAINS

T DSE 8610 MKII-

SIMILARDSE 8610 MKII

-SIMILAR

ATS8



FER SWITCH*



(Kg)

AS-SEM-BLY@ 3 x 208 V @ 3 x 400 V @ 3 x 480 V

Panel offered in a metal cabinet with an IP-67 protection level, featuring the same items as the ATS panel, except that the INSTALLED control switchboard on the panel is the DSE 8660 MKII or similar.

Floor panel


Rev. 02 | 17/10/2018

AUTOMATIC TRANSFER SWITCH PANEL PARALLEL WITH THE MAINS (2 GENSETS OR MORE)ATS8P

ATS8P-0100/4 100 36 69 83 C ABB AF52 DSE 8660 4 700x500x260 40 WATS8P-0125/4 125 45 87 104 C ABB AF80 DSE 8660 4 700x500x260 40 WATS8P-0150/4 150 54 104 125 C TERASAKI TC100A/4 DSE 8660 4 1200x600x300 75 WATS8P-0260/4 260 94 180 216 C TERASAKI TC225A/4 DSE 8660 4 1200x600x300 85 WATS8P-0350/4 350 126 242 291 C TERASAKI TC330A/4 DSE 8660 4 1000x800x400 105 WATS8P-0420/4 420 151 291 349 C TERASAKI TC400A/4 DSE 8660 4 1000x800x400 105 WATS8P-0660/4 660 238 457 548 C TERASAKI TC630A/4 DSE 8660 4 1700x1000x400 230 SATS8P-1000/4 1000 360 692 830 C GE CK1000A DSE 8660 4 1700x1000x400 210 SATS8P-1250/4 1250 450 865 1038 MCB ABB T7S1250 DSE 8660 4 1700x1000x400 200 SATS8P-1600/4 1600 576 1107 1328 MCB ABB T7S1600 DSE 8660 4 1700x1000x400 200 SATS8P-2000/4 2000 720 1384 1660 MCB ABB E2.2B2000 DSE 8660 4 1700x1800x800 505 SATS8P-2500/4 2500 900 1730 2075 MCB ABB E2.2N2500 DSE 8660 4 1700x1800x800 545 SATS8P-3200/4 3200 1152 2214 2656 MCB ABB E4.2N3200 DSE 8660 4 1700x2200x600 545 S


FUNCTIONALITYThis panel has a switchboard type DSE 8660 MKII or similar that detects when a mains failure occurs and sends a start-up signal to the switchboard type DSE 8610, DEIF COMAP or similar on each of the gensets that make up the parallel system (2 or more gensets) Once started and synchronised, the panel switchboard sends commands, opening and closing contactors / motor-driven circuit breakers (WITHOUT INTERLOCK) to change the supply from the mains to the generator set.

When the mains is restored, the switchboard operates to enable the change of supply from the generator sets to the mains, enabling the synchronisation for a few seconds, and afterward it sends signals to the generator set switchboards (DSE 8610 MKII or similar) to stop the engines.

The generator sets work in sync with each other, in stand-by to the mains, and are synchronised with the mains upon its restoration.


1

DSE 8660 MKII-

SIMILAR

LOAD


G2G1

MAINS

T DSE 8610 MKII-

SIMILARDSE 8610 MKII

-SIMILAR

ATS8P



FER SWITCH*



(Kg)

AS-SEM-BLY@ 3 x 208 V @ 3 x 400 V @ 3 x 480 V

Wall panel

DESCRIPTIONPanel offered in a metal cabinet with an IP-67 protection level, featuring the same items as the ATS panel, except that the transfer switch consists of two contactors or two motor-driven circuit breakers WITHOUT INTERLOCK 1 and the INSTALLED control switchboard on the panel is the DSE 8660 MKII or similar.


Rev. 02 | 17/10/2018

APPLICATIONS EXAMPLES




T2

MAINS 2

DSE 334DSE 334

ATS 1 ATS 2

GENERATOR SET

LOADLOAD

T1

MAINS 1

GDSE 6110 MKII

ONE GENSET IN STAND-BY WITH 2 OR MORE MAINS.

Typical example of 2 or more buildings, each with their main panel (2 or more different mains) and a single generator set in stand-by to all the mains, with an ATS on each load.

It can also be a single mains that powers several buildings, each of which has its own ATS.

Note - The generator set only supplies energy to the panel with a power outage.

TWO MANUAL GENSETS WITH SIGNALLED START-UP, ONE AS A BACKUP FOR THE OTHER WITH AN ATS (VERY USEFUL FOR RENTERS).

It applies to fully standard generator sets with different powers and different brand engines.

The generator sets are programmed to alternate their service.

AMF PANEL (V2) WITH BY-PASS (FOR ISOLATING VOLTAGE OF THE GENSET AND THE AMF CIRCUIT IN MAINTENANCE TASKS).It is also applicable to LTS and ATS panels and gensets in parallel.

DSE 334


LOAD

G2G1 DSE 3110DSE 3110

ATS

DSE 7320 MKII

GENERATOR SET

LOADT

MAINS

G

AMF


Rev. 02 | 17/10/2018

APPLICATIONS EXAMPLES




TWO MANUAL GENSETS WITH DSE 7310 MKII, ONE AS A BACKUP FOR THE OTHER, WITH AN LTS AND STAND-BY WITH THE MAINS BY MEANS OF AN ATS.

This feature is achieved by complementing the previous application with a standard ATS panel.

TWO MANUAL GENSETS WITH DSE 7310 MKII, ONE AS A BACKUP FOR THE OTHER WITH AN LTS (VERY USEFUL FOR RENTERS).

LTS is completely standard and the gensets only need an RS 485 cable to connect them and programming.

The gensets are programmed to switch their service.

TWO AUTOMATIC GENSETS WITH DSE 7320 MKII, ONE AS A BACKUP FOR THE OTHER AND IN STAND-BY WITH THE MAINS BY MEANS OF TWO LTSs.

A redundant power supply system is achieved in this application using two standard V3-type generator sets and 2 LTSs.

The only complements necessary are a RS485 communication cable and programming.


RS 485G2G1

DSE 334

LOAD

T

MAINS

ATS

LTS + MSTB

DSE 7310 MKII DSE 7310 MKII


RS 485

LOAD

G2G1 DSE 7310 MKII DSE 7310 MKII

LTS


RS 485G2G1

LOAD

T

MAINS

LTS

LTS + MSTB

DSE 7320 MKII DSE 7320 MKII


Rev. 02 | 17/10/2018

DSE 334 TECHNICAL INFORMATION

CONTROL UNITS

6020 MKII TECHNICAL INFORMATION


DSE 6120 MKIIControl module in stand-by to the mains

The DSE 6120 MKII is an automatic switchboard for use in stand-by with the mains, developed to offer a wide range of options for gensets that work alone (not parallel).

DSE 334Control module in stand-by to the mains

The DSE 334 is an automatic switchboard for transfer switch control.

It monitors the AC supply from S1 (primary source) and, in case of failure, it detects it and sends a start-up signal to S2 (secondary source). Once S2 is available and producing an output current within the limits, the DSE 334 that controls the transfer switch, will send a signal to change the load from S1 to S2. When the S1 current supply is again within the limits, the DSE 334 will give the order to return the load to S1 and turn the S2 off.

DSE 7320 MKIIControl module in stand-by to the mains

The DSE 7320 MKII is an advanced switchboard that includes all the characteristics of DSE 6120 MKII with more features, inputs, and outputs. It monitors several parameters of the engine and the alternator. It also includes USB, RS 232, and RS 485 communication ports, as well as DSENet® dedicated terminals for system expansion.

DSE 8620 TECHNICAL INFORMATION

DSE 8620Stand-by and mains synchronisation control module

The DSE 8620 is an automatic switchboard for use in stand-by with the mains, with outage-free reconnection (parallel with the mains without outage) It is designed to synchronise a single generator set set with a single power supply. In addition to carrying out the full control of the genset, the DSE 8620 switchboard will automatically control the change from the mains power supply to the generator set source or, once the mains are restored, of the generator set synchronised to the mains, restoring power without outage.


DSE 8660 MKIIStand-by control module with 1 or more mains.

The DSE 8660 is an automatic switchboard for use in stand-by with one or more mains that controls the operation of a system of generator sets connected in parallel. Designed to synchronize single or multiple DSE 8610 MKII and DSE 8680 controllers with one or more power supplies. The DSE 8660 MKII will automatically control the change from the mains to the generator set or generator sets power supply and vice versa (from the generator sets to the mains) when power is restored. This last change may be carried out through a mains reconnection with or without outage.


DSE 8610 MKIIControl and synchronisation module for several generator sets

The DSE 8610 MKII is an automatic synchronization control module. It is normally used in a system where the load is shared by several gensets. The DSE 8610 MKII monitors the generator set and shows the operative status and the failure conditions, automatically starting or stopping the engine according to the load demand or failure condition.

For all 200 kVA engines and above.

For all 250 kVA engines and above.


Rev. 02 | 17/10/2018


DEIF COMAP

Generic panel (NO TRANSFER SWITCH) with any type of switchboard.(INMESOL V3 version with automatic switchboard for open gensets)

FUNCTIONALITYIt is a generic panel that may operate any switchboard type depending on the required function; from manual control switchboards with signal start to automatic switchboards in stand-by to the mains set-up..

It is an ideal panel suitable for control panel renovation in generator sets with some use or those that will be used for different uses.


DESCRIPCIÓNControl circuit presented in a metal cabinet with an IP-67 protection grade with the following elements:


2. Battery charger.

3. Terminal block for the connection of the alternator input control, mains, intensity transformers, and external transfer switch control wires..

4. Terminal block for controlling the generator set engine.

5. Control switchboard.


7. Start switch for switchboard power supply.

6 73

8

9

1

4

52

Wall panel

G

ANYSWITCH-BOARD

GENERATOR SET

CONTROL panel

LOAD

Switchboard upgrades:For equipment that requires greater performance than what is available as standard.

Upgrades to switchboards from other brands:

DSE 6120 MKII TO DSE 7320 MKII SWITCHBOARD UPGRADE(in AMF)

DSE 334 TO DSE335 SWITCHBOARD UPGRADE(in ATS)

DSE 6120 MKII DSE 7320 MKII DSE 334 DSE 335DSE 6120 MKII DSE 7320 MKII


Rev. 02 | 17/10/2018


DSE 80037” full color, with RS485 port. Overview of multiple DSE 86XX, 87XX, and 88XX, max. 1.2 km

DSE 800410” full color, with RS485 port. Overview of multiple DSE 86XX, 87XX, and 88XX, max. 1.2 km

DSE 2520Up to 3 DSE 2520 per DSE 7320 MKII, max. 1 km

Remote displays:Remote screens provide a view of the information that appears in the control switchboxes of the generator set. These are useful for controlling the genset from a certain distance without having to be in front of the set.

DSE 2130 Digital and analogue input modules.

DSE 2548Signalling modules, up to 8 individual LEDS, maximum distance 1 km.

DSE 2133RTD input modules / Thermopolar (PT 100, PT 1000, etc.)

DSE 2157Output relays with potential-free contacts

DSE 2152Analogue output modules (0-10 V, 4-20 mAmp)

Expansion Modules:There is a wide range of input and output expansion module devices available, which enable greater flexibility for meeting the specifications of complex installations controlled by the generator set switchboard.

DSE 2131Proportional input modules (0-10 V, 4-20 mAmp)

DSE 891 - ETHERNET DSE 892 - SNMP

DSE 855 - USB-ETHERNET

DSE 890 - 3G

MODEM GSM

Remote control:Several remote control devices that connect the DSE switchboards from the generator sets to external systems via 3G, Ethernet, SNMP, US-Ethernet and USB-RS485 are available.

This enables controlling the generator set from a distance by means of a computer, tablet, or mobile phone.

DSE 857 - USB-RS485


Rev. 02 | 17/10/2018


KIT OF 4 OUTPUT RELAYSFor obtaining potential-free contacts or for converting a 230V input into a battery negative input to the controller.

TERMINAL BLOCKS FOR ALUMINIUM POWER CABLESNeeded when the load cables connecting to the genset are made in Aluminium.

EXTENDED CABLES INSTEAD OF THE STANDARD (6M))When the genset must be more than 6m away from the panel.

DSE160 DOUBLE POWER SOURCE (IN AMF AND ATS)Prevents drops in voltage if there is a considerable distance between the generator set and the panel. It is installed on the panel and can be powered by either the mains or the generator.

INTERIOR LIGHTINGProvides visibility within the panel indoors or at night.

DSEP100 MODULE FOR DECOUPLING FROM THE MAINS WITH (DSE 8620)This is a decoupling relay for protecting generator sets in parallel with the mains.

ANTICONDENSATION RESISTANCEIt is installed in the electric cabinet or on the panel. It is used to avoid condensation that may damage the electrical components.

SWITCH TO THERMAL FUSESBroken fuses have to be replaced and thermal fuses are not replaced, but rather reset.

Other accessories:

DIGITAL SCHEDULE PROGRAMMERFor programming the operating hours of a generator set.

SMART BATTERY CHARGERKeeps batteries charged at their maximum capacity all the time. It includes a LED indicator to inform normal or overcharged conditions, which helps to identify the status. Accepts multiple AC voltage connections. Using the DSE 73XX MKII switchboard makes it possible to display information from the battery charger on the front screen and to oversee defects or failures and its status, as well as the battery’s life cycle.

MANUAL BY-PASSIt is used to isolate the transfer switch on a load

mains - genset - transfer switch and being able to proceed to maintenance/repair safely.

(Check the page with applications examples).

Rev. 02 | 17/10/2018

MORE INFORMATION: www.inmesol.com

These details shown on this data sheet are intended for guidance only. Inmesol reserves the right to change the details without prior notice. The present documents will not be part of any sales contract.

INMESOL, S.L.CENTRAL HEAD OFFICECarretera de Fuente Álamo, 2. 30153 Corvera · MURCIA. SPAINPhone: +34 968 38 03 00 | Fax: +34 968 38 04 00Email: [email protected]

www.inmesol.com

Inmesol, S.L. company with ISO 9001 quality management system certificate and ISO 14001 Environmental Management System Certificate for the: “Design, manufacture, marketing and technical assistance of power generator sets, lighting towers, welding generators, tractor with PTO generator set and hybrid generation systems.”

Inmesol is present in over 80 countries worldwide

Documents

AUTOMATIC AND TRANSFER SWITCH PANELS · amf automatic mains failure panels ats automatic transfer ... bottom cap for wiring inlet. single-line diagram and ... amf-0050/2 50 6 11,5