AutoPump Catalog...Long AP2-Bottom Inlet Short AP2-Bottom Inlet 2” Top Inlet AP Pumps Long AP2-Top Inlet Short AP2-Top Inlet Long AP3B 54 Short AP3B 58 Bottom Bottom 2.63 / 6.68

AutoPump ® CatalogThe Original Automatic Air-Powered Pumps

Sites Around the World

Complete Systems

Featuring the AP andAP4+ Series

AAuuttooPPuummpp®®

AutoPump Automatic Air-Powered Pumps

Automatic air-powered pumps o�er exceptional capabilities in the severe pumping conditions found at manyland�ll and remediation sites. QED’s patented AutoPump originated the automatic air-powered pump conceptin 1986 and have lead the industry ever since. AutoPumps were designed speci�cally to handle di�cultconditions reliably and safely, including hydrocarbons, land�ll lechates and condensates, solvents, suspendedsolids, silts, corrosives, and high viscosities, along with high temperatures and frequent starts and stops.Air-powered AutoPumps are proven worldwide at thousands of sites, which is why AutoPumps are the No. 1choice of professionals based on reliability, durability, performance range and technical support.

Unlike electric pumps, air-powered AutoPumps use no high-speed motors, bearings or impellers, soAutoPumps don’t heat up, sieze up or get ground up. Liquid shearing is typical of electric pumps, creatingoil-water emulsions that reduce the performance of downstream treatment equipment. AutoPumps cause farless liquid shearing than electric submersible pumps so downstream treatment systems can perform better.Air-powered also means eliminating the dangers and costs of electricity at and in the well. Finally,AutoPumps actually have a built-in control system - they pump when there is liquid present and shut downwhen the level is drawn down, without the need for any sensors in the well or controls at the surface.

Application Excellence

Experience and ExpertiseThe AutoPump specialists at QED have unsurpassed experience in both typical and special applications,providing the quality and care that makes a di�erence. Call us at 1-800-624-2026 for prompt, professionalassistance, or visit our web site at www.qedenv.com to access product and application information.

The superiority of the AutoPump design is based on four key strengths:high clearance �uid pathwaysusing air as the motive forcematerials of construction matched to site conditionsa simple yet rugged operating mechanism

Remediation applications and land�ll �uids pumping are very challenging. QED is dedicated to providing acomprehensive approach to meeting the speci�c needs of each site and well, taking into account manyfactors beyond just �ow rate and depth, such as:

Preferred inlet position- top or bottomPump length to match water column and meet drawdown requirementsA broad range of materials of construction to match �uid properties and temperatureJacketed tubing sets, bundled hose and quick-connect options to ease installation and serviceA wide variety of standard and custom wellhead completions to �t site needs

AutoPump ®

Table of Contents

2

3

4

62

63

64

65

66

67

Inside Back Cover

5

6-9

10-13

14-17

18-21

22-25

26-29

30-33

34-37

38-41

42-45

46-49

50-53

54-57

58-61

Long AP4 + Bottom Inlet Pump

Short AP4 + Bottom Inlet Pump

Low-Drawdown AP4 + Bottom Inlet Pump

Long AP4 + Top Inlet Pump

Short AP4 + Top Inlet Pump

Low-Drawdown AP4 + Top Inlet Pump

How AutoPumps Work

Long AP3 Bottom Inlet Pump

Short AP3 Bottom Inlet Pump

Why AutoPumps Are Better

Guide to AutoPumps Selection

Complete Systems

Long AP3 Top Inlet Pump

Short AP3 Top Inlet Pump

Long AP2 Bottom Inlet Pump

Short AP2 Bottom Inlet Pump

Long AP2 Top Inlet Pump

Short AP2 Top Inlet Pump

Tubing and Hose

Well Caps

Flow Counters

Air Supply

Tank-Full Shuto�

Application Data Sheet

Warranty

AutoPump ®

How AutoPumps Work

Fill Cycle Discharge Cycle

The �uid pushes the inlet check valveopen and �uid enters the pump.

With the air inlet open, air pressurebuilds up within the pump body. Thiscauses the �uid inlet check valve toclose and forces the �uid to bedisplaced up and out of the �uid outlet.

As the �uid level falls, the �oat movesdownward to the bottom of its stroke.

In this lower position, the �oat triggersthe lever assembly to close the airsupply and open the air exhaust valve.And a new cycle begins.

Note: This illustration is for a bottom �lling format. Atop loader is also available with both the inlet anddischarge at the top of the pump.

AutoPump Reliability

The AutoPump operating cycle diagrams and explanation above tell just part of the story of AutoPump

technology. Engineering an automatic pump to function in clear water is just the start. The real secrets

of AutoPump durability and reliability are based on over 18 years of site experience in di�cult pumping

applications. AutoPumps are designed to resist chemical attack, abrasive wear, mechanical wear,

solids deposits, viscous �uids and elevated temperatures. The entire air valve control mechanism has

been re�ned in many subtle ways to survive these severe pumping conditions, using special materials,

tolerances, and safety factors to provide years of trouble-free cycling. AutoPumps are the �rst of their

kind, �rst in design experience, and �rst in reliability and durability.

2

As the �uid level rises, air is expelled

In this upper position, the �oattriggers a lever assembly, whichcloses the air exhaust valve and

opens the air inlet allowing air toenter and pressurize the pump.

through the exhaust air valveand the internal �oat rises to

the top of its stroke.

AP

4+

AutoPum

p

3

AutoPump®

1.800.624.2026 F 1.734.995.1170 [email protected] www.qedenv.com

Why AutoPumps Are Better

2355 Bishop Circle West Dexter, MI 48130 USA

Superior float.

QED-developed unique “Easy Fittings”

For quick disconnect/reconnect without the need to shorten pump tubing

or remove/replace tubing clamps.

Superior body. Light weight, won’t corrode, won’t dent.

Same standard 5-year warranty. No other pneumatic pump manufacturer

even comes close.

Maximum flow rate over 14 gpm.

Easy pump disassembly. Removing four bolts allows removal

of the pump casing.

Easy O-ring fit due to precision tolerance casing I.D.

Inlet check plug design durability has been proven at thousands of sites in over 40 countries.

Easily removable float retainer.

Superior materials choice. Most of the AutoPump’s internal components are available in a variety of materials to fit site specific conditions.

QED originated the concept of jacketed tubing to make pump installation/removal easier.

The same time-proven, reliable, air valve assembly that has made the AP4 the industry’s preferred choice since 1986.

Air efficiency Saves up to $300/year in energy costs compared to other pneumatic pumps.

AutoPump ®

Guide to AutoPump Selection

AutoPumps Model Pg# Out. Diameter Overall Lengthin/cm in/cm

Max. Flow 1 Max. Depth Act. Levelgpm/lpm ft/m in/cm

53 / 135

2.3 / 8.82 300 / 91.4 35 / 892 / 7.57 300 / 91.4 20 / 51

300 / 91.4 52 / 132300 / 91.4 31 / 78

1 Consult for higher �ow requirements2 High Pressure Option for 4” AP pumps3 Optional radial inlet model provides 11.5” / 29 cm actuation level4 Optional 2.63” (6.68cm) OD available

4

Quick Guide to AutoPump SelectionAn important advantage of an AutoPump system is the wide range of choices to truly match site needs. Belowis a quick guide to the major con�gurations and options o�ered in the AutoPump line, to help you determinewhich models are best for your project. Of course, you can just call us at 1-800-624-2026, or email us [email protected], for fast, personal service by our application specialists.

As a general guideline, pump model selection is usually based on the following primary application criteria.They are presented in the common sequence of consideration, but special site needs may alter the priority.

Maximum �ow and depth - pump model, depth, submergence and drive pressure determine themaximum �ow rate that can be achieved; see speci�c pump curves for detailed �ow information

Pump Diameter - to �t the well ID; also, larger diameter pumps deliver higher �ow rates, all otherfactors being equal

Inlet Position - top or bottom inlet; a top inlet enhances removal of LNAPLs, while bottom inletsprovide the highest �ow rates and greatest solids-handling capacity for DNAPL, dissolved and land�ll �uids

Actuation Level - minimum height of liquid needed to actuate the pump, also equal to the minimumdrawdown level; low-drawdown models are optimized for maximum drawdown

Materials of construction - many models are available in upgraded materials for special applications,such as extremes of pH, suspended solids, high temperatures and aggressive solvents

InletPosition

3” Bottom Inlet AP PumpsLong AP3-Bottom InletShort AP3-Bottom Inlet

3”Top Inlet AP PumpsLong AP3-Top InletShort AP3-Top Inlet

2” Bottom Inlet AP PumpsLong AP2-Bottom InletShort AP2-Bottom Inlet

2” Top Inlet AP PumpsLong AP2-Top InletShort AP2-Top Inlet

Long AP3B 54Short AP3B 58

BottomBottom

2.63 / 6.682.63 / 6.68

52 / 13242 / 107

Long AP3T 62Short AP3T 66

TopTop

3.4 / 8.64 4

3.4 / 8.64 457 / 14547 / 119

Long AP2B 70Short AP2B 74

BottomBottom

1.75 / 4.451.75 / 4.45

55 / 13933 / 85

Long AP2T 78Short AP2T 82

TopTop

1.75 / 4.451.75 / 4.45

57 / 14435 / 89

1.9 / 7.21.6 / 6.0

31 / 79175 / 53.3 22 / 56

7.3 / 27.6 220 / 676 / 22.7

5.4 / 20 220 / 674.8 / 18.1 175 / 53.3 42 / 107

5

AutoPump®

Complete Systems

Complete AutoPump® systems offer the greatest assurance of a smooth installation, dependable perfor-mance and easy maintenance. Common system components include:

In-well hose and tubing - see page 86

Barbs, quick-connects and other fitting options - see page 87

Wellhead completion caps and flanges - see page 87

Cycle counters - see page 88

Air system filter/regulators - see page 89

Call or visit www.qedenv.com for prompt assistance with all of the above.

Basic Pump Systems

Basic System Bottom Inlet Pump Basic System Top Inlet Pump

Fluid Discharge

Air Supply From Compressor

Water

Barb Fittings

Cycle Counter

AP4 Bottom Inlet

Note:Support Harness andrope omitted for clarity

AutoPump ®

AP4+B Bottom Inlet, Long

14 gpm (60 lpm)*

3.5 in (8.9 cm)

53 in. (135 cm) o�ered to handle even the most severe remediation and

2.

3.

4.

5. Five-year warranty

* Consult for higher �ow requirements

6

Description

The AP4 + Bottom Inlet Long AutoPump provides maximumcapabilities and �ow in a bottom inlet pump for 4” (100 mm)diameter and larger wells. The base model delivers �owrates up to 14 gpm (53 lpm)*, and optional versions are

land�ll pumping applications. The AP4+ Long Bottom InletAutoPump is complemented by the most comprehensiveselection of accessories to provide a complete system tomeet site-speci�c requirements. Call QED for prompt, no-obligation assistance on your pumping project needs.

The AutoPump HeritageThe AP4 + Bottom Inlet Long AutoPump is part of the famousAutoPump family of original automatic air-powered pumps,developed in the mid 1980s speci�cally to handle uniquepumping needs at remediation and land�ll sites. Over theyears they’ve proven their durability at thousands of sitesworldwide. AutoPumps are designed to handle di�cultpumping challenges that other pumps can’t, such as hydro-carbons, solvents, suspended solids, corrosives, tempera-ture extremes, viscous �uids and frequent start/stop cycles.Beyond just the pump, AutoPump systems o�er the mostcomplete range of tubing, hose, connectors, wellhead capsand accessories to help your installation go smoothly. Thissuperior pumping heritage, application experience and supportback up every AutoPump you put to work on your project.

Max. Flow

O.D.

Length

Advantages

1. The original automatic air-powered well pump, provenworldwide over 18 years

The highest �ow rates anddeepest pumping capabilities inthe industry

Patented, proven design forsuperior reliability anddurability, even in severeapplications

Handles solids, solvents,hydrocarbons corrosiveconditions, viscous �uids andhigh temperatures beyond thelimits of electric pumps

7

AutoPump®

Bottom Inlet, Long AP4+BPump Dimensions Specifications & Operating Requirements

Long and short AP4+ AutoPumps are warranted for five(5) years: 100% materials and workmanship first three(3) years; 50% materials and workmanship for the fourth(4th) and fifth (5th) years.

Low-Drawdown AutoPumps are warranted for one (1) year.

Application Limits(Base model)AP4+ AutoPumps are designed to handlethe application ranges described below.For applications outside these ranges,consult QED about AP4 upgrades.

Maximum Temperature: 150°F (65°C)pH Range: 4-9Solvents and Fuels: diesel, gasoline, JP1-JP6,#2 heating oils, BTEX, MTBE, landfill liquids

ModelLiquid Inlet Location

ODLength Overall (pump & fittings)

Length Overall, w / Extended ScreenWeight

Max. Flow RatePump Volume / Cycle

Min. Actuation Level

Standard PumpMax. Depth

Air Pressure RangeAir Usage

High Pressure PumpMax. Depth

Air Pressure Range

Min. Liquid Density

Standard Construction Materials1

Pump BodyPump Ends

Internal ComponentsTube & Hose Fittings

Fitting Type

Tube & Hose OptionsTubing Material2

Sizes - Liquid DischargePump Air Supply

Air ExhaustHose Material


Air Exhaust

1 Material upgrades available2 Applies to QED supplied tubing;

other tubing sources may notconform to QED fittings.

4" - Long AP4+ Bottom InletBottom3.5 in. (8.9 cm)53 in. (135 cm)56 in. (142 cm)16 lbs. (7.3 kg)14 gpm (53 lpm) - See Flow Rate Chart*0.58 - 0.78 gal (2.2 - 3.0L )35 in. (89 cm)

250 ft. (76 m)5 - 120 psi (0.4 - 8.4 kg/cm2)0.4-1.1 scf / gal. (3.0-8.5 liters of air /fluid liter) - See Air usage chart

425 ft. (130 m)5 - 200 psi (0.4 - 14.1 kg/cm2)

0.7 SpG (0.7 g/cm3)

Fiberglass or Stainless SteelStainless Steel, UHMWPE3, BrassStainless Steel, Viton, Acetal, PVDF4

Brass or Stainless SteelBarbs or Quick Connects

Nylon1 in. (25 mm) or 1-1/4 in. (32 mm) OD1/2 in. (13 mm) OD5/8 in. (16 mm) ODNitrile3/4 in. (19 mm) or 1 in. (25 mm) ID3/8 in. (9.5 mm) ID1/2 in. (13 mm) ID

3 UHMWPE - Ultra High Molecular Weight Polyethylene

4 PVDF - Polyvinylidene Fluoride

*Consult for higher flow requirements

Len

gth

wit

h S

tan

dar

d S

cree

n 4

1" (

104

cm)

Act

uat

ion

Lev

el 2

7" (

69 c

m)

Len

gth

wit

h O

pti

on

al E

xten

ded

Scr

een

Att

ach

ed 4

4."

(113

cm

)

Inlet

Air Supply

Exhaust

O.D. 3.5" (89 mm)

Liquid Discharge

AutoPump ®

AP4+B Bottom Inlet, Long

Flow Rates 1

18 68.1 18 68.1

16 60.6 16 60.6

14 53 14 53

12 AIR INLET PRESSURES 45.4 12 AIR INLET PRESSURES 45.4

10 37.9 10 37.9

8 30.3 8 30.3

6 22.7 6 22.7

4 15.1 15.14

2 7.6 2 7.6

0 020 40 60 80 100 120 140 160 180 200 0 406.1 12.2 18.3 24.4 30.5 36.6 42.7 48.8 54.9 61

18 68.1 18 68.1

16 60.6 16 60.6

14 53 14 53


10 37.9 10 37.9

8 30.38 30.3

6 22.7 6 22.7

4 15.1 4 15.1

2 7.6 2 7.6

0 0 00 20 40 60 160 180 200

6.1 12.2 30.5 54.9 61

18 68.1 18 68.1

16 60.6 16 60.6

14 53 14 53


10 37.9 10 37.9

8 30.3 30.38

6 22.7 6 22.7

4 15.1 4 15.1

7.62 7.6 2

0 00 20 40 160 180 200

0 20 40 60 80 100 120 140 160 180 200 6.1 12.2 30.5 54.9 616.1 12.2 30.5 54.9 61

1FLOW RATES MAY VARY WITH SIT E CONDITIONS. CALL FOR TECH NICAL ASSISTANCE.

8

6-INCH (15 cm) SUBMERGENCE OF PUMP HEAD 6-INCH (15 cm) SUBMERGENCE OF PUMP HEAD

GALLONS

PER

MINUTE

WITH

3/4-INCH

I.D. HOSE

APPROXIMATE

LITERS

PER

MINUTE

WITH

19 mm

I.D. HOSE

GALLONS

PER

MINUTE

WITH

1-INCH

I.D. HOSE

APPROXIMATE

LITERS

PER

MINUTE

WITH

25.4 mm

I.D. HOSE

100 PSI7 Kg/cm 2100 PSI

7 Kg/cm 2

40 PSI3 Kg/cm 2

2 FT. (60 cm) SUBMERGENCE OF PUMP HEAD

70 PSI5 Kg/cm 2

70 PSI5 Kg/cm 2

0FT.Meters

0FT.DEPTH

IN WELL 206.1 12.2

DEPTH IN WELL

GALLONS

PER

MINUTE

WITH

3/4-INCH

I.D. HOSE

APPROXIMATE

LITERS

PER

MINUTE

WITH

19 mm

I.D. HOSE

GALLONSGALLONS

PER

MINUTE

WITH

1-INCH

I.D. HOSE

APPROXIMATE

LITERS

PER

MINUTE

WITH

25.4 mm

I.D. HOSE100 PSI7 Kg/cm 2

100 PSI7 Kg/cm 2


70 PSI5 Kg/cm 2

0FT.Meters

DEPTH IN WELL

DEPTH IN WELL

GALLONS

PER

MINUTE

WITH

3/4-INCH

I.D. HOSE

APPROXIMATE

LITERS

PER

MINUTE

WITH

19 mm

I.D. HOSE

GALLONS

PER

MINUTE

WITH

1-INCH

I.D. HOSE

APPROXIMATE

LITERS

PER

MINUTE

WITH

25.4 mm

I.D. HOSE

100 PSI7 Kg/cm 2

100 PSI7 Kg/cm 2

40 PSI3 Kg/cm 2

18.3 24.4

70 PSI5 Kg/cm 2

36.6 42.7 48.8

70 PSI5 Kg/cm 2

36.6 42.7 48.8

0FT.Meters

0FT.Meters

DEPTH IN WELL

DEPTH IN WELL

40 PSI3 Kg/cm 2

40 PSI3 Kg/cm 2

40 PSI3 Kg/cm 2

40 PSI3 Kg/cm 2

0


70 PSI5 Kg/cm 2

80 100 120 14036.6 42.7 48.818.3 24.4


60 80 100 120 14018.3 24.4

60 80 100 120 140 160 180 20018.3 24.4 30.5 36.6 42.7 48.8 54.9 61 Meters

3/4 inch (19 mm)Inside Diameter Discharge Hose

(Equivalent to 1-Inch O.D. Tubing)

1 inch (25.4 mm)Inside Diameter Discharge Hose

(Equivalent to 1.25-Inch O.D. Tubing)

0 20 40 60 80 100 120 140 160 180 200 FT.6.1 12.2 18.3 24.4 30.5 36.6 42.7 48.8 54.9 61 Meters

9

AutoPump®

Bottom Inlet, Long AP4+BAir Consumption

.2

.3

.4

.5

.6

.7

.8

.9

20 40 60 80 100 120 140 160 180 200

1.1

1.0

1.2

1.3

1.4

1.5

1.6

70 PSI

MetersFT.

36.61.6 2.21 3.81 24.4 30.5 169.457.24 8.84

(STD L/LITER)LITER PUMPED

LITER OF AIRSTANDARD

PER

2.2

1.5

3.0

3.7

5.2

4.5

6.0

7.5

6.7

8.2

9.0

10.5

9.7

11.2

12

APPROXIMATE

5 Kg/cm 2

DEPTH IN WELL

STANDARDCUBIC FEET OF AIR PERGALLON PUMPED(SCF/GAL)

100 PSI7 Kg/cm 2

40 PSI3 Kg/cm 2

.2

.3

.4

.5

.6

.7

.8

.9

20 40 60 80 100 120 140 160 180 200

1.1

1.0

1.2

1.3

1.4

1.5

1.6


MetersFT.

36.61.6 2.21 3.81 24.4 30.5 169.457.24 8.84



PER

2.2

1.5

3.0

3.7

5.2

4.5

6.0

7.5

6.7

8.2

9.0

10.5

9.7

11.2

12

APPROXIMATE

IN WELL DEPTH

100 PSI7 Kg/cm 2

70 PSI5 Kg/cm 2

40 PSI23 Kg/cm

3/4 inch (19 mm)Inside Diameter Discharge Hose(Equivalent to 1-Inch O.D. Tubing)

1 inch (25.4 mm)Inside Diameter Discharge Hose(Equivalent to 1.25-Inch O.D. Tubing)

AutoPump ®

AP4+B Bottom Inlet, Short

13 gpm (49 lpm)

3.5 in (8.9 cm)

41 in. (104 cm)

o�er the most complete range of tubing, hose, connectors,

2.

3.

4.



10

Description

The AP4 + Bottom Inlet Short AutoPump provides maximumcapabilities and �ow in a bottom inlet pump for 4” (100 mm)diameter and larger wells with shorter water columns and/orthe need to pump down to lower water levels, compared tofull-length pumps. It is o�ered in optional versions tohandle even the most severe remediation and land�llpumping applications, and delivers �ow rates up to 13 gpm(49 lpm)*. The AP4 + Short Bottom Inlet AutoPump iscomplemented by the most comprehensive selection ofaccessories to provide a complete system to meet site-speci�c requirements. Call QED for prompt, no-obligationassistance on your pumping project needs.

The AutoPump HeritageThe AP4+ Bottom Inlet Short AutoPump is part of thefamous AutoPump family of original automatic air-poweredpumps, developed in the mid 1980s speci�cally to handleunique pumping needs at remediation and land�ll sites.Over the years they’ve proven their durability at thousandsof sites worldwide. AutoPumps are designed to handledi�cult pumping challenges that other pumps can’t, suchas hydrocarbons, solvents, suspended solids, corrosives,temperature extremes, viscous �uids and frequent start/stop cycles. Beyond just the pump, AutoPump systems

wellhead caps and accessories to help your installation gosmoothly. This superior pumping heritage, applicationexperience and support back up every AutoPump you putto work on your project.

Max. Flow

O.D.

Length

Advantages





11

AutoPump®

Bottom Inlet, Short

Pump Dimensions Specifications & Operating RequirementsL

eng

th w

ith

Sta

nd

ard

Scr

een

41"

(10

4 cm

)

Act

uat

ion

Lev

el 2

7" (

69 c

m)

Len

gth

wit

h O

pti

on

al E

xten

ded

Scr

een

Att

ach

ed 4

4."

(113

cm

)

Inlet

Air Supply

Exhaust

O.D. 3.5" (89 mm)

Liquid Discharge









Air Pressure Range

Min. Liquid Density


Pump BodyPump Ends


Fitting Type





Air Exhaust


other tubing sources may not conform to QED fittings.

4" - Short AP4+ Bottom InletBottom3.5 in. (8.9 cm)41 in. (104 cm)44 in. (112 cm)13 lbs. (5.9 kg)13 gpm (49 lpm)* - See Flow Rate Chart0.22 - 0.36 gal (.83 - 1.36L )27 in. (69 cm)

250 ft. (76 m)5 - 120 psi (0.4 - 8.4 kg/cm2)0.4-1.5 scf / gal. (1.5 - 5.7 liters of air /fluid liter) - See air usage chart

425 ft. (130 m)5 - 200 psi (0.4 - 14.1 kg/cm2)

0.7 SpG (0.7 g/cm3)




3 UHMWPE - Ultra High Molecular Weight Polyethylene4 PVDF - Polyvinylidene Fluoride


Long and short AP4+ AutoPumps are warranted for five(5) years: 100% materials and workmanship first three(3) years; 50% materials and workmanship for the fourth(4th) and fifth (5th) years.

Low-Drawdown for the AutoPumps are warranted for one(1) year.



AP4+B

AutoPump ®

AP4+B Bottom Inlet, Short

Flow Rates 1

1 inch (25.4 mm)Inside Diameter Discharge Hose(Equivilant to 1.25-Inch O.D. Tubing)

6-INCH (15 cm) SUBMERGENCE OF PUMP HEAD 6-INCH (15 cm) SUBMERGENCE OF PUMP HEAD18 68.1 18 68.1

16 60.6 16 60.6

14 53 5314


10 37.9 10 37.9

8 30.3 8 30.3

6 22.7 6 22.7

4 15.1 4 15.1

2 7.6 2 7.60 0

0 40 0 40

18 68.1 18 68.116 60.6 16 60.6

14 53 14 53

12 AIR INLET PRESSURES 45.4 12 AIR INLET PRESSURES 45.410 37.9 10 37.9

8 30.3 8 30.36 22.7

6 22.74 15.1

4 15.12 7.6

2 7.60 0

0 0

10 FT. (300 cm) SUBMERGENCE OF PUMP HEAD18 68.1 10 FT. (300 cm) SUBMERGENCE OF PUMP HEAD

18 68.116 60.6

16 60.614 53

531412 AIR INLET PRESSURES 45.4

12 AIR INLET PRESSURES 45.410 37.9

10 37.98 30.3

22.78 30.3

66

4 15.122.7

4 15.12 7.6

07.62

0 20 40 180 200 06.1 12.2 30.5 54.9 61 0 20 40 180 200

6.1 12.2 30.5 54.9 61


12

GALLONS

PER

MINUTE

WITH

3/4-INCH

I.D. HOSE

APPROXIMATE

LITERS

PER

MINUTE

WITH

19 mm

I.D. HOSE

GALLONS

PER

MINUTE

WITH

1-INCH

I.D. HOSE

APPROXIMATE

LITERS

PER

MINUTE

WITH

25.4 mm


100 PSI7 Kg/cm 2

40 PSI3 Kg/cm 2


40 PSI3 Kg/cm 2


0FT.

0FT.20

6.1 12.2DEPTH IN WELL

206.1 12.2

DEPTH IN WELL

GALLONS

PER

MINUTE

WITH

3/4-INCH

I.D. HOSE

APPROXIMATE

LITERS

PER

MINUTE

WITH

19 mm

I.D. HOSE

GALLONS

PER

MINUTE

WITH

1-INCH

I.D. HOSE

APPROXIMATE

LITERS

PER

MINUTE

WITH

25.4 mm


100 PSI7 Kg/cm 2

40 PSI3 Kg/cm 2 40 PSI

3 Kg/cm 2

DEPTH IN WELL DEPTH

IN WELL

GALLONS

PER

MINUTE

WITH

3/4-INCH

I.D. HOSE

APPROXIMATE

LITERS

PER

MINUTE

WITH

19 mm

I.D. HOSE

GALLONS

PER

MINUTE

WITH

1-INCH

I.D. HOSE

APPROXIMATE

LITERS

PER

MINUTE

WITH

25.4 mm

I.D. HOSE


7 Kg/cm 2

40 PSI3 Kg/cm 2

0FT.Meters

70 PSI5 Kg/cm 2160

36.6 42.7 48.8DEPTH IN WELL

0FT.Meters

16036.6 42.7 48.8

DEPTH IN WELL


5 Kg/cm 2


3 Kg/cm 2

70 PSI

60 80 100 120 14018.3 24.4 60 80 100 120 140

18.3 24.4

70 PSI5 Kg/cm 2 5 Kg/cm 2

60 80 100 120 140 160 180 20018.3 24.4 30.5 36.6 42.7 48.8 54.9 61 Meters

60 80 100 120 140 160 180 20018.3 24.4 30.5 36.6 42.7 48.8 54.9 61 Meters



0 20 40 60 80 100 120 140 160 180 200 FT.6.1 12.2 18.3 24.4 30.5 36.6 42.7 48.8 54.9 61 Meters 0 20 40 60 80 100 120 140 160 180 200 FT.

6.1 12.2 18.3 24.4 30.5 36.6 42.7 48.8 54.9 61 Meters

13

AutoPump®

Bottom Inlet, Short

IN WELL DEPTH

.2

.3

.4

.5

.6

.7

.8

.9

20 40 60 80 100 120 140 160 180 200

1.1

1.0

1.2

1.3

1.4

1.5

1.6

MetersFT.

36.61.6 2.21 3.81 24.4 30.5 169.457.24 8.84



PER

2.2

1.5

3.0

3.7

5.2

4.5

6.0

7.5

6.7

8.2

9.0

10.5

9.7

11.2

12

APPROXIMATESTANDARDCUBIC FEET OF AIR PERGALLON PUMPED(SCF/GAL)

40 PSI23 Kg/cm

70 PSI25 Kg/cm

100 PSI7 Kg/cm 2

.2

.3

.4

.5

.6

.7

.8

.9

20 40 60 80 100 120 140 160 180 200

1.1

1.0

1.2

1.3

1.4

1.5

1.6

MetersFT.

36.61.6 2.21 3.81 24.4 30.5 169.457.24 8.84



PER

2.2

1.5

3.0

3.7

5.2

4.5

6.0

7.5

6.7

8.2

9.0

10.5

9.7

11.2

12

APPROXIMATE

IN WELL DEPTH


100 PSI7 Kg/cm 2

70 PSI5 Kg/cm 2

40 PSI3 Kg/cm 2

Air Consumption



AP4+B

AutoPump ®

LDAP4+B Low-Drawdown, Bottom Inlet

7.0 gpm (26.5 lpm)

3.5 in (8.9 cm)

25 in. (63.5 cm)

2.

3.

4.

5. One-year warranty

14

Description

The AP4+ Low-Drawdown Bottom Inlet AutoPump providesmaximum capabilities and �ow in a bottom inlet pump for4” (100 mm) diameter and larger wells with very shortwater columns and/or the need to pump down to as lowas 11.5 inches (29 cm) above the bottom. It is o�ered inoptional versions to handle even the most severe remediationand land�ll pumping applications, and delivers �ow rates upto 7 gpm (26.5 lpm). The AP4 + Low Drawdown Bottom InletAutoPump is complemented by the most comprehensiveselection of accessories to provide a complete system tomeet site speci�c requirements. Call QED for prompt,no-obligation assistance on your pumping project needs.

The AutoPump HeritageThe AP4+ Low-Drawdown Bottom Inlet AutoPump is part ofthe famous AutoPump family of original automatic air-powered pumps, developed in the mid 1980s speci�callyto handle unique pumping needs at remediation and land�llsites. Over the years they’ve proven their durability atthousands of sites worldwide. AutoPumps are designed tohandle di�cult pumping challenges that other pumps can’t,such as hydrocarbons, solvents, suspended solids,corrosives, temperature extremes, viscous �uids andfrequent start/stop cycles. Beyond just the pump,AutoPump systems o�er the most complete range oftubing, hose, connectors, wellhead caps and accessoriesto help your installation go smoothly. This superiorpumping heritage, application experience and support backup every AutoPump you put to work on your project.

Max. Flow

O.D.

Length

Advantages


The highest �ow rates anddeepest pumping capabilities inthe industry in a low drawdownbottom-�ll pump



15

AutoPump®

Low-Drawdown, Bottom Inlet

Low-Drawdown AP4+ AutoPumps warranted for one (1)year: 100% materials and workmanship.

Specifications & Operating RequirementsPump Dimensions

Liquid Discharge

Inlet

* Optional radial inlet model provides11.5" (29 cm) actuation level

Air Supply

Exhaust

O.D. 3.5" (89 mm)

Leng

th w

ith S

tanda

rd S

cree

n 25"

(63.5

cm)

Act

uatio

n Le

vel *

13"

(33.

2 cm

)

Leng

th w

ith O

ption

al Ex

tende

d Scr

een A

ttach

ed 28

" (71

cm)





Max. DepthAir Pressure Range


Air Usage

Min. Liquid Density


Pump BodyPump Ends


Fitting Type Tube & Hose Options

Tubing Material2Sizes - Liquid Discharge

Pump Air SupplyAir Exhaust

Hose MaterialSizes - Liquid Discharge

Pump Air SupplyAir Exhaust

1Material upgrades available2 Applies to QED supplied tubing;


4" - Low-Drawdown AP4+ Bottom InletBottom ( standard plug type check valve)3.5 in. (8.9 cm)25 in. (63.5 cm)28 in. (71.1 cm)11 lbs. (5.0 kg)7 gpm (26.5 lpm)0.11 - 0.16 gal (.42 - .61L)250 ft. (76 m)5 - 120 psi (0.4 - 8.4 kg/cm2)13 in. (33.2 cm) standard outlet11.5 in. (29 cm) w/ radial inlet.32 - 2.86 scf/gal (2.2 - 21.5 liters of air/fluidliter) See air usage chart0.7 SpG (0.7 g/cm3)








LDAP4+B

AutoPump ®

LDAP4+B Low-Drawdown, Bottom Inlet

Flow Rates 1

9 34.1 9 34.1


7 26.5 26.57

6 22.7 6 22.7

18.9 18.95 5

4 15.1PSI 4 15.12

3 11.4 3 11.4

7.6 7.62 2

1 3.8 1 3.8

0 00 20 40 60 80 180 200 0 20 40 60 80 100 120

6.1 12.2 18.3 24.4 30.5 36.6140

6.1 12.2 18.3 24.4 54.9 61 42.7

9 34.1 9 34.1

8 30.3 8 30.3


6 22.7 6 22.7

5 18.9 5 18.9

4 15.1 4 15.12

32

3 11.4 11.4

2 7.6 2 7.62

1 3.8 1 3.8

0 00 20 40 60 80 180 200 140 160 180 200

6.1 12.2 18.3 24.4 54.9 61 42.7 48.8 54.9 61 Meters

9 34.1 9 34.1

8 30.3 8 30.3


6 22.7 6 22.7

18.95 5 18.9

4 15.1 4 15.12 2

3 11.4 3 11.4

7.62 2 7.6

1 3.8 1 3.8

0 0140 160 180 200 FT.

42.7 48.8 54.9 61 Meters

00 20 0 20 40 60 80 100 120

6.1 12.2 18.3 24.4 30.5 36.6140 160

6.1 12.2 42.7 48.8 54.9 61 Meters


16


GALLONS

PER

MINUTE

WITH

3/4-INCH

I.D. HOSE

APPROXIMATE

LITERS

PER

MINUTE

WITH

19 mm

I.D. HOSE

GALLONS

PER

MINUTE

WITH

1-INCH

I.D. HOSE

APPROXIMATE

LITERS

PER

MINUTE

WITH

25.4 mm

I.D. HOSE

100 7 Kg/cm 2

100 PSI7 Kg/cm

40 PSI3 Kg/cm 2

70 PSI5 Kg/cm 2

40 PSI3 Kg/cm 2

70 PSI5 Kg/cm 2

0FT.Meters

0160 180 200 FT.

48.8 54.9 61 Meters


140 16042.7 48.8

DEPTH IN WELL

DEPTH IN WELL

GALLONS

PER

MINUTE

WITH

3/4-INCH

I.D. HOSE

APPROXIMATE

LITERS

PER

MINUTE

WITH

19 mm

I.D. HOSE

GALLONSGALLONS

PER

MINUTE

WITH

1-INCH

I.D. HOSE

APPROXIMATE

LITERS

PER

MINUTE

WITH

25.4 mm

I.D. HOSE

100 PSI7 Kg/cm

100 PSI7 Kg/cm

40 PSI3 Kg/cm


5 Kg/cm 270 PSI

5 Kg/cm 2

0FT.Meters

0FT.140 160

42.7 48.8DEPTH IN WELL

DEPTH IN WELL

GALLONS

PER

MINUTE

WITH

3/4-INCH

I.D. HOSE

APPROXIMATE

LITERS

PER

MINUTE

WITH

19 mm

I.D. HOSE

GALLONS

PER

MINUTE

WITH

1-INCH

I.D. HOSE

APPROXIMATE

LITERS

PER

MINUTE

WITH

25.4 mm

I.D. HOSE

100 PSI7 Kg/cm

100 PSI7 Kg/cm

40 PSI3 Kg/cm 2


5 Kg/cm 270 PSI

5 Kg/cm 2

0180 200 FT.DEPTH

IN WELL DEPTH IN WELL

100 12030.5 36.6


100 120 0 20 40 60 80 100 12030.5 36.6


6.1 12.2 18.3 24.4 30.5 36.6


40 60 80 100 12018.3 24.4 30.5 36.6





17

AutoPump®

Low-Drawdown, Bottom Inlet

GALLON PUMPED(SCF/GAL)

IN WELL DEPTH

STANDARDCUBIC FEET OF AIRPER

(STD L/LITER)

601.6 2.21 3.81

.3

20.2

.4

.5

4036.624.4 30.5

80 100 120

.8

.7

.6

.9

1.0

1.3

1.2

1.1

1.4

1.5

9.457.24 8.84081041 061

Meters61

2.2

FT.1.5

200

3.0

3.7

6.0

4.5

5.2

6.7

7.5

9.7

9.0

8.2

10.5

11.2

STANDARDAPPROXIMATE

LITER PUMPED

LITER OF AIR

2.6

2.1

1.7

1.6

1.8

1.9

2.0

2.2

2.3

2.4

2.5

2.7

2.8

2.9

19.4

15.7

PER12.7

13.5

12

14.2

15

16.5

17.2

18.7

18.0

20.2

20.9

21.7

7 Kg/cm100 PSI

2

270 PSI

5 Kg/cm

40 PSI3 Kg/cm 2

IN WELL DEPTH

PER

(SCF/GAL)GALLON PUMPED

CUBIC FEET OF AIRSTANDARD

.2

6.63 7.245.034.422.21 3.816.120 14040 60 80 100 120

1.5

Meters54.9 61180 200 FT.160

48.8

.5

.3

.4

3.7

2.2

3.0

.8

.6

.7

6.0

4.5

5.2

11.21.5

9.01.2

1.1

.9

1.0

8.2

6.7

7.5

1.3

1.4

9.7

10.5

LITER OF AIR13.51.8

1.6

1.7

(STD L/LITER)LITER PUMPED12

PER12.7

2.1

1.9

2.0

15.7

STANDARD14.2APPROXIMATE

15

2.4

2.2

2.3

18.0

16.5

17.2

2.7

2.5

2.6

20.2

18.7

19.4

2.8

2.9

20.9

21.7

100 PSI7 Kg/cm 2

70 PSI5 Kg/cm 2

3 Kg/cm 240 PSI

Air Consumption



LDAP4+B

AutoPump ®

AP4+T Top Inlet, Long

10 gpm (38 lpm)

3.5 in (8.9 cm)

57 in. (145 cm) o�ered in optional versions to handle even the most severe

o�er the most complete range of tubing, hose, connec-

2.

3.

4.



18

Description

The AP4+ Top Inlet Long AutoPump provides maximumcapabilities and �ow in a top inlet pump for 4” diameterand larger wells needing an elevated inlet, such as pumpingtotal �uids from wells contaminated with LNAPLs. It is

remediation and land�ll pumping applications, and delivers�ow rates up to 10 gpm*. The AP4 + Long Top InletAutoPump is complemented by the most comprehensiveselection of accessories to provide a complete system tomeet site-speci�c requirements. Call QED for prompt, no-obligation assistance on your pumping project needs.

The AutoPump HeritageThe AP4 + Top Inlet Long AutoPump is part of the famousAutoPump family of original automatic air-powered pumps,developed in the mid 1980s speci�cally to handle uniquepumping needs at remediation and land�ll sites. Over theyears they’ve proven their durability at thousands of sitesworldwide. AutoPumps are designed to handle di�cultpumping challenges that other pumps can’t, such ashydrocarbons, solvents, suspended solids, corrosives,temperature extremes, viscous �uids and frequent start/stop cycles. Beyond just the pump, AutoPump systems

tors, wellhead caps and accessories to help your installa-tion go smoothly. This superior pumping heritage, applica-tion experience and support back up every AutoPump youput to work on your project.

Max. Flow

O.D.

Length

Advantages





19

AutoPump®

Top Inlet, Long

Pump Dimensions Specifications & Operating Requirements

Inlet

Air Supply

Exhaust

O.D. 3.5" (89 mm)

Liquid Discharge

Len

gth

to

To

p o

f F

itti

ng

s 5

7" (

145

cm)

Act

uat

ion

Lev

el 5

2" (

132

cm)

AP4+ AutoPumps are warranted for five (5) years: 100%materials and workmanship for the first three (3) years;50% materials and workmanship for the fourth (4th) andfifth (5th) years.

Standard Application Limits(standard model)AP4+ AutoPumps are designed to handlethe application ranges described below.For applications outside these ranges,consult QED.




WeightMax. Flow Rate

Pump Volume / CycleMin. Actuation Level




Air Pressure Range

Min. Liquid Density


Pump BodyPump Ends


Fitting Type





Air Exhaust

1 Material upgrages available2 Applies to QED supplied tubing;


4" - Long AP4+ Top InletTop3.5 in. (8.9 cm) OD57 in. (145 cm) OD18 lbs. (8.7 kg)10 gpm (38 lpm) - See Flow Rate Chart0.58 - 0.78 gal (2.2 - 3.0L )52 in. (132 cm)

250 ft. (76 m)5 - 120 psi (0.4 - 8.4 kg/cm2)0.35-1.1 scf / gal. (3.0-8.4 liters of air / fluid liter)

425 ft. (130 m)5 - 200 psi (0.4 - 14.1 kg/cm2)

0.7 SpG (0.7 g/cm3)

Fiberglass or Stainless SteelStainless Steel, Acetal, BrassStainless Steel, Viton, Acetal, PVDF3




AP4+T

AutoPump ®

AP4+T Top Inlet, Long

Flow Rates 1

18 68.1 18 68.1

16 60.6 16 AIR INLET PRESSURES 60.6

14 53 14 53

12 AIR INLET PRESSURES 45.4 12 45.4

10 37.9 10 37.9

8 30.3 8 30.3

6 22.7 6 22.7

4 15.1 4 15.1

2 7.6 2 7.6

0 0 00 20 40 0 20 40 60 80 100 120 140 160 180 200 FT.

6.1 12.2 12.2 18.3 24.4 30.5 36.6 42.7 48.8 54.9 61 Meters

18 68.1 18 68.1

16 60.6 16 60.6

14 53 14 AIR INLET PRESSURES 53

12 AIR INLET PRESSURES 45.4 12 45.4

10 37.9 10 37.9

8 30.3 8 30.3

6 22.7 6 22.7

4 15.1 4 15.1

2 7.6 2 7.6

0 0 0 00 20 40 60 80 100 120 140 160 180 200 FT.

12.2 18.3 24.4 30.5 36.6 42.7 48.8 54.9 61 Meters

18 68.1 1818 68.168.1

16 60.6 1616 60.660.6

14 53 1414 AIR INLET PRESSURES 5353

12 AIR INLET PRESSURES 45.4 1212 45.445.4

37.910 1010 37.937.9

8 30.3 88 30.330.3

6 22.7 66 22.722.7

15.14 44 15.115.1

2 7.6 22 7.67.6

0 00 000 20 40 160 180 200 0 20 40 60 80 100 120 140 160 180 200

6.1 12.2 30.5 54.9 61 6.1 12.2 18.3 24.4 30.5 36.6 42.7 48.8 54.9 61


20


GALLONS

PER

MINUTE

WITH

3/4-INCH

I.D. HOSE

APPROXIMATE

LITERS

PER

MINUTE

WITH

19 mm

I.D. HOSE

GALLONS

PER

MINUTE

WITH

1-INCH

I.D. HOSE

APPROXIMATE

LITERS

PER

MINUTE

WITH

25.4 mm

I.D. HOSE

100 PSI7 Kg/cm 2

100 PSI7 Kg/cm 2

40 PSI3 Kg/cm 2

40 PSI3 Kg/cm 2

70 PSI5 Kg/cm 2


0FT. DEPTH

IN WELL DEPTH IN WELL

GALLONS

PER

MINUTE

WITH

3/4-INCH

I.D. HOSE

APPROXIMATE

LITERS

PER

MINUTE

WITH

19 mm

I.D. HOSE

GALLONSGALLONS

PER

MINUTE

WITH

1-INCH

I.D. HOSE

APPROXIMATE

LITERS

PER

MINUTE

WITH

25.4 mm

I.D. HOSE

100 PSI7 Kg/cm 2

100 PSI7 Kg/cm 2

40 PSI3 Kg/cm 2

40 PSI3 Kg/cm 2

70 PSI5 Kg/cm 2


DEPTH IN WELL

DEPTH IN WELL

GALLONS

PER

MINUTE

WITH

3/4-INCH

I.D. HOSE

APPROXIMATE

LITERS

PER

MINUTE

WITH

19 mm

I.D. HOSE

GALLONS

PER

MINUTE

WITH

1-INCH

I.D. HOSE

APPROXIMATE

LITERS

PER

MINUTE

WITH

25.4 mm

I.D. HOSE

100 PSI7 Kg/cm 2

100 PSI7 Kg/cm 2


3 Kg/cm 270 PSI5 Kg/cm 2

36.6 42.7 48.8

0FT.Meters

DEPTH IN WELL

FT.Meters

DEPTH IN WELL

70 PSI5 Kg/cm 2

70 PSI5 Kg/cm 2

40 PSI3 Kg/cm 2

6.1


6.1


60 80 100 120 14018.3 24.4

60 80 100 120 140 160 180 20018.3 24.4 30.5 36.6 42.7 48.8 54.9 61 Meters





0 20 40 60 80 100 120 140 160 180 200 FT.6.1 12.2 18.3 24.4 30.5 36.6 42.7 48.8 54.9 61 Meters

21

AutoPump®

Top Inlet, Long

.2

.3

.4

.5

.6

.7

.8

.9

20 40 60 80 100 120 140 160 180 200

1.1

1.0

1.2

1.3

1.4

1.5

1.6

70 PSI

MetersFT.

36.61.6 2.21 3.81 24.4 30.5 169.457.24 8.84



PER

2.2

1.5

3.0

3.7

5.2

4.5

6.0

7.5

6.7

8.2

9.0

10.5

9.7

11.2

12

APPROXIMATE

5 Kg/cm 2

IN WELLDEPTH


100 PSI7 Kg/cm 2

40 PSI3 Kg/cm 2

.2

.3

.4

.5

.6

.7

.8

.9

20 40 60 80 100 120 140 160 180 200

1.1

1.0

1.2

1.3

1.4

1.5

1.6

MetersFT.

36.61.6 2.21 3.81 24.4 30.5 169.457.24 8.84



PER

2.2

1.5

3.0

3.7

5.2

4.5

6.0

7.5

6.7

8.2

9.0

10.5

9.7

11.2

12

APPROXIMATE

IN WELL DEPTH


40 PSI23 Kg/cm

70 PSI5 Kg/cm 2

100 PSI7 Kg/cm 2

Air Consumption



AP4+T

22

AutoPump®

Top Inlet, Short

Max. Flow

O.D.

Length

9 gpm (34 lpm)

3.5 in (8.9 cm)

42 in. (107 cm)

Description

The AP4+ Top Inlet Short AutoPump provides maximumcapabilities and flow in a top inlet pump for 4” (100 mm)diameter and larger wells with shorter water columns andthe need for an elevated inlet, such as pumping total fluidsfrom wells contaminated with LNAPLs. It is offered inoptional versions to handle even the most severeremediation and landfill pumping applications, and deliversflow rates up to 9 gpm (34 lpm)*. The AP4+ Short Top InletAutoPump is complemented by the most comprehensiveselection of accessories to provide a complete system tomeet site-specific requirements. Call QED for prompt, no-obligation assistance on your pumping project needs.

The AutoPump HeritageThe AP4+ Top Inlet Short AutoPump is part of the famousAutoPump family of original automatic air-powered pumps,developed in the mid 1980s specifically to handle uniquepumping needs at remediation and landfill sites. Over theyears they’ve proven their durability at thousands of sitesworldwide. AutoPumps are designed to handle difficultpumping challenges that other pumps can’t, such ashydrocarbons, solvents, suspended solids, corrosives,temperature extremes, viscous fluids and frequent start/stop cycles. Beyond just the pump, AutoPump systemsoffer the most complete range of tubing, hose, connectors,wellhead caps and accessories to help your installation gosmoothly. This superior pumping heritage, applicationexperience and support back up every AutoPump you put towork on your project.


Advantages


2. The highest flow rates anddeepest pumping capabilities inthe industry

3. Patented, proven design forsuperior reliability anddurability, even in severeapplications

4. Handles solids, solvents,hydrocarbons corrosiveconditions, viscous fluids andhigh temperatures beyond thelimits of electric pumps


AP4+T

23

AutoPump®

Top Inlet, Short


AP4+ AutoPumps are warranted for five (5) years: 100%materials and workmanship for the first three (3) years;50% materials and workmanship for the fourth (4th) andfifth (5th) years.

Low-Drawdown AutoPumps are warranted for one (1) year.

Inlet

Air Supply

Exhaust

O.D. 3.5" (89 mm)

Liquid Discharge

Len

gth

to

To

p o

f F

itti

ng

s 4

2" (

107

cm)

Act

uat

ion

Lev

el 3

7" (

94 c

m)






Pump Volume / CycleMin. Actuation Level




Air Pressure Range

Min. Liquid Density


Pump BodyPump Ends


Fitting Type





Air Exhaust



4" - Short AP4+ Top InletTop3.5 in. (8.9 cm)42 in. (107 cm)17 lbs. (7.8 kg)9 gpm (34 lpm) - See Flow Rate Chart0.22 - 0.36 gal (.83 - 1.36L )37 in. (94 cm)

250 ft. (76 m)5 - 120 psi (0.4 - 8.4 kg/cm2)0.35-1.5 scf / gal. (2.4-11.3 liters of air /fluid liter) - See Air Usage Chart

425 ft. (130 m)5 - 200 psi (0.4 - 14.1 kg/cm2)

0.7 SpG (0.7 g/cm3)





AP4+T

24

AutoPump®

00

12.2400

6.120 FT.

Meters200

61180

54.980 140120100

30.560

18.3 42.736.624.4 48.8160

2

4

7.6

15.1

IN WELL DEPTH

FT.20018040 80 14012010060 1600 20 DEPTH

8

6

30.3

22.7

12

10

45.4

37.9

68.118

16

14

60.6

53


12.26.1 Meters9.45 1630.518.3 42.736.624.4 48.8 IN WELL

15.14

2

0

7.6

0

8

6

30.3

22.7

12

10

45.4

37.9

16

14

60.6

53

PER LITERS45.412


18

12.26.1

68.1

Meters8.84 9.45 1642.736.630.524.418.30 4020

2

0

FT.

0

7.6

2001801601401201008060

70 PSI25 Kg/cm

IN WELL DEPTH

WITH

MINUTE

PER

I.D. HOSE

19 mm

3/4-INCH

I.D. HOSE 6

4 15.1

22.7

WITH

MINUTE 10

8

37.9

30.3

APPROXIMATEGALLONS

16

14

60.6

53

6-INCH (15 cm) SUBMERGENCE OF PUMP HEAD18 68.1

MINUTE

I.D. HOSE

3/4-INCH

WITH

PER

GALLONS

PER

I.D. HOSE

19 mm

WITH

MINUTE

LITERS

APPROXIMATE

MINUTE

I.D. HOSE

3/4-INCH

WITH

PER

GALLONS

PER

I.D. HOSE

19 mm

WITH

MINUTE

LITERS

APPROXIMATE

AIR INLET PRESSURES

40 PSI3 Kg/cm 2 25 Kg/cm

70 PSI

7 Kg/cm 2100 PSI

40 PSI3 Kg/cm 2

5 Kg/cm 270 PSI

7 Kg/cm 2100 PSI

AIR INLET PRESSURES

40 PSI3 Kg/cm 2

100 PSI27 Kg/cm

AIR INLET PRESSURES

1FLOW RATES MAY VARY WITH SITE CONDITIONS. CALL FOR TECHNICAL ASSISTANCE.

Top Inlet, Short



Flow Rates1



8

4

0

2

6

12

10

14

16

18

206.1

4012.2

6018.3

8024.4

10030.5

12036.6

14042.7

16048.8

18054.9

20061

30.3

22.7

7.6

0

15.1

FT.Meters

53

37.9

45.4

6-INCH (15 cm) SUBMERGENCE OF PUMP HEAD

60.6

68.1

0

31.75 mm

O.D. TUBING

LITERS

PER

MINUTE

WITH

APPROXIMATE

1.25-INCH

O.D. TUBING

GALLONS

PER

MINUTE

WITH

DEPTH IN WELL

4

0

2

6

8

10

12

18

14

16

15.1

0

7.6

22.7

30.3

37.9

45.4

68.1

53

60.6

DEPTH IN WELL

4

0

2

6

8

10

12

18

14

16

15.1

0

7.6

22.7

30.3

37.9

45.4

68.1

53

60.6

DEPTH IN WELL

206.1

0 16048.824.4 36.6 42.718.3

6030.5100 120 1408040

12.2 54.9180

61200

MetersFT.

206.1

0 16048.824.4 36.6 42.718.3

6030.5100 120 1408040

12.2 54.9180

61200

MetersFT.

O.D. TUBING

1.25-INCH

WITH

MINUTE

PER

GALLONS

PER

O.D. TUBING

31.75 mm

MINUTE

WITH

LITERS

APPROXIMATE

O.D. TUBING

1.25-INCH

WITH

MINUTE

PER

GALLONS

PER

O.D. TUBING

31.75 mm

MINUTE

WITH

LITERS

APPROXIMATE

AIR INLET PRESSURES

27 Kg/cm100 PSI

25 Kg/cm70 PSI40 PSI

3 Kg/cm 2

AIR INLET PRESSURES

27 Kg/cm100 PSI

240 PSI

3 Kg/cm 2

AIR INLET PRESSURES

27 Kg/cm100 PSI

2

40 PSI3 Kg/cm 2

5 Kg/cm70 PSI

5 Kg/cm70 PSI

AP4+T

25

AutoPump®

IN WELL DEPTH

.2

.3

.4

.5

.6

.7

.8

.9

20 40 60 80 100 120 140 160 180 200

1.1

1.0

1.2

1.3

1.4

1.5

1.6

MetersFT.

36.618.31.6 2.21 24.4 30.5 48.842.7 54.9 61



PER

2.2

1.5

3.0

3.7

5.2

4.5

6.0

7.5

6.7

8.2

9.0

10.5

9.7

11.2

12

APPROXIMATESTANDARDCUBIC FEET OF AIR PERGALLON PUMPED(SCF/GAL)

40 PSI23 Kg/cm

70 PSI25 Kg/cm

100 PSI7 Kg/cm 2

.2

.3

.4

.5

.6

.7

.8

.9

20 40 60 80 100 120 140 160 180 200

1.1

1.0

1.2

1.3

1.4

1.5

1.6

MetersFT.

36.618.31.6 2.21 24.4 30.5 48.842.7 54.9 61



PER

2.2

1.5

3.0

3.7

5.2

4.5

6.0

7.5

6.7

8.2

9.0

10.5

9.7

11.2

12

APPROXIMATE

IN WELL DEPTH


70 PSI5 Kg/cm 2

100 PSI7 Kg/cm 2

40 PSI3 Kg/cm 2

Air Consumption

Top Inlet, Short



AP4+T

26

AutoPump®

Advantages

Max. Flow

O.D.

Length

6.4 gpm (24 lpm)

3.5 in (8.9 cm)

29 in. (74 cm)

Description

The Low-Drawdown AP4+ Top Inlet AutoPump providesmaximum capabilities and flow in a top inlet pump for 4”(100 mm) diameter and larger wells with very short watercolumns and/or the need to pump down to as low as 24inches (62 cm) above the bottom. It is offered in optionalversions to handle even the most severe remediation andlandfill pumping applications, and delivers flow rates up to6.4 gpm (24 lpm). The Low Drawdown AP4+ Top InletAutoPump is complemented by the most comprehensiveselection of accessories to provide a complete system tomeet site-specific requirements. Call QED for prompt, no-obligation assistance on your pumping project needs.

The AutoPump HeritageThe Low-Drawdown AP4+ Top Inlet AutoPump is part of thefamous AutoPump family of original automatic air-poweredpumps, developed in the mid 1980s specifically to handleunique pumping needs at remediation and landfill sites.Over the years they’ve proven their durability at thousandsof sites worldwide. AutoPumps are designed to handledifficult pumping challenges that other pumps can’t, suchas solvents, suspended solids, corrosives, temperatureextremes, viscous fluids and frequent start/stop cycles.Beyond just the pump, AutoPump systems offer the mostcomplete range of tubing, hose, connectors, caps andaccessories to help your installation go smoothly. Thissuperior pumping heritage, application experience andsupport back up every AutoPump you put to work onyour project.


2. The highest flow rates anddeepest pumping capabilities inthe industry in a low drawdowntop-fill pump

3. Patented, proven design forsuperior reliability anddurability, even in severeapplications

4. Handles solids, solvents,corrosive conditions, viscousfluids and high temperaturesbeyond the limits of electricpumps


Low-Drawdown, Top InletLDAP4+T

27

AutoPump®


Low-Drawdown AP4+ AutoPumps are warranted for one(1) year: 100% material and workmanship.



Inlet

Air Supply

Exhaust

O.D. 3.5" (89 mm)

Liquid Discharge

Len

gth

to

To

p o

f F

itti

ng

s 2

9" (

74 c

m)

Act

uat

ion

Lev

el 2

4" (

62 c

m)




Pump Volume / CycleMax. Depth

Air Pressure RangeMin. Actuation Level

Air Usage

Min. Liquid Density


Pump BodyPump Ends


Fitting Type





Air Exhaust


other tubing sourcesmay not conform to QED fittings.

4" - Low-Drawdown AP4+ Top InletTop3.5 in. (8.9 cm)29 in. (74 cm)11 lbs. (5.0 kg)6.4 gpm (24 lpm)0.11 - 0.16 gal (.42 - .61L)250 ft. (76 m)5 - 120 psi (0.4 - 8.4 kg/cm2)24 in. (62 cm).31 - 2.85 scf/gal (2.2 - 21.5 liters of air/fluid liter) see air usage chart0.7 SpG (0.7 g/cm3)





Low-Drawdown, Top Inlet LDAP4+T

28

AutoPump®

Low-Drawdown, Top Inlet

00

18.9MINUTE 5

48.842.736.612.26.1 18.3 24.4 30.5 Meters9.45 16 IN WELL 160140120400 20 8060

0100 FT.200180 DEPTH

0

1 3.8

2I.D. HOSE7.6

I.D. HOSE

3/4-INCH

WITH

WITH15.14

3 19 mm11.4

MINUTE


GALLONS

PER LITERS6PER

22.7

7 APPROXIMATE26.5

8 30.3

9 34.1

48.842.736.612.26.1 18.3 24.4 30.5 Meters9.45 16 IN WELL16014012040 806020 100

00

0FT.200180 DEPTH

1 3.8

2 I.D. HOSE7.6

18.95

I.D. HOSE

3/4-INCH

WITH

WITH

3 19 mm11.4

4MINUTE

15.1

GALLONS

MINUTE

PER LITERS22.76

PER

7APPROXIMATE

26.5


8 30.3

9 34.1

Meters8.84 9.45 1642.736.6 IN WELL12.2 24.418.3 30.56.116014012040 8060 1000 20 FT.200180 DEPTH


1 3.8

2I.D. HOSE7.6

3/4-INCH

I.D. HOSE

WITH

3 19 mm11.4

4 WITH15.1MINUTE

26.57GALLONS

MINUTE

PER LITERS22.76

5PER18.9

APPROXIMATE

8 30.3

9 34.1

3 Kg/cm40 PSI

2 70 PSI25 Kg/cm

7 Kg/cm 2100 PSI

AIR INLET PRESSURES

3 Kg/cm 240 PSI

70 PSI5 Kg/cm 2

27 Kg/cm100 PSI

AIR INLET PRESSURES

25 Kg/cm70 PSI

3 Kg/cm 240 PSI

100 PSI27 Kg/cm

AIR INLET PRESSURES

00

18.9MINUTE 5

48.842.736.612.26.1 18.3 24.4 30.5 Meters9.45 16 IN WELL 160140120400 20 8060

0100 FT.200180 DEPTH

0

1 3.8

2 7.6 I.D. HOSE

I.D. HOSE

1-INCH

WITH15.1 WITH4

3 25.4 mm11.4

MINUTE


GALLONS

PER LITERS6 22.7

PER

7APPROXIMATE

26.5

8 30.3

9 34.1

48.842.736.612.26.1 18.3 24.4 30.5 Meters9.45 16 IN WELL 160140120

040 80600 20 100

0FT.200180 DEPTH

1 3.8

2 I.D. HOSE7.6

5 18.9

1-INCH

I.D. HOSE

WITH

WITH

3 11.4 25.4 mm

4MINUTE

15.1

MINUTE

GALLONSGALLONS

PER LITERS22.76

PER

7 26.5APPROXIMATE


8 30.3

9 34.1

Meters8.84 9.45 1642.736.6 IN WELL 12.26.1 24.418.3 30.51601401200 4020 8060 100 FT.200180 DEPTH


1 3.8

2I.D. HOSE7.6

1-INCH

I.D. HOSE

WITH

3 25.4 mm11.4

4 WITH15.1MINUTE

26.57GALLONS

MINUTE

PER LITERS22.76

5PER18.9

APPROXIMATE

8 30.3

9 34.1

40 PSI3 Kg/cm 2

5 Kg/cm70 PSI

2

7 Kg/cm100 PSI

2

AIR INLET PRESSURES

3 Kg/cm240 PSI

5 Kg/cm270 PSI

27 Kg/cm100 PSI

AIR INLET PRESSURES

23 Kg/cm40 PSI

25 Kg/cm70 PSI

100 PSI27 Kg/cm

AIR INLET PRESSURES

1 FLOW RATES MAY VARY WITH SITE CONDITIONS. CALL FOR TECHNICAL ASSISTANCE.



Flow Rates1

LDAP4+T

29

AutoPump®

Low-Drawdown, Top Inlet

IN WELL DEPTH

.2 1.5160

48.81.6 2.21 3.81 24.4 30.5 36.6 42.7021 04100108060402

Meters54.9 61180 200 FT.

.3

.4

.5

2.2

3.0

3.7

.7

.6

.8

5.2

4.5

6.0

1.0

.9

1.1

7.5

6.7

8.2

1.8 LITER OF AIR13.5

1.5 11.2

1.2

1.3

1.4

9.0

9.7

10.5

GALLON PUMPED1.6(SCF/GAL)

PER1.7


PER12.7

STANDARDCUBIC FEET OF AIR

1.9

2.0

2.1

APPROXIMATESTANDARD14.2

15

15.7

2.3

2.2

2.4

17.2

16.5

18.0

2.8 20.9

2.6

2.5

2.7

19.4

18.7

20.2

2.9 21.7

7 Kg/cm100 PSI

70 PSI2

2

5 Kg/cm

40 PSI3 Kg/cm 2

IN WELL DEPTH

.2 1.5160

48.836.61.6 2.21 3.81 24.4 30.5 42.720 14040 60 80 100 120

Meters54.9 61180 200 FT.

.3

.4

.5

2.2

3.0

3.7

.7

.6

.8

5.2

4.5

6.0

1.0

.9

1.1

7.5

6.7

8.2

LITER OF AIR1.8 13.5

1.5 11.2

1.2

1.3

1.4

9.0

9.7

10.5

GALLON PUMPED1.6(SCF/GAL)

PER1.7


PER12.7

STANDARDCUBIC FEET OF AIR

1.9

2.0

2.1

APPROXIMATESTANDARD14.2

15

15.7

2.3

2.2

2.4

17.2

16.5

18.0

2.8 20.9

2.6

2.5

2.7

19.4

18.7

20.2

2.9 21.7

100 PSI7 Kg/cm 2

70 PSI25 Kg/cm

40 PSI3 Kg/cm 2

Air Consumption



LDAP4+T

30

AutoPump®

Bottom Inlet, LongAP3BMax. Flow

O.D.

Length

7.3 gpm (27.6 lpm)

2.63 in (6.68 cm)

52 in. (132 cm)

Description

The AP3B Bottom Inlet Long AutoPump is designed formoderate-duty remediation pumping applications with wellcasings 3” (75 mm) diameter and larger. Call QED for prompt,no-obligation assistance on your pumping project needs.

The AutoPump HeritageThe AP3B Bottom Inlet Long AutoPump is part of thefamous AutoPump family of original automatic air-poweredpumps, developed in the mid 1980s specifically to handleunique pumping needs at remediation and landfill sites.Over the years they’ve proven their durability at thousandsof sites worldwide. AutoPumps are designed to handledifficult pumping challenges that other pumps can’t, suchas solvents, suspended solids, corrosives, temperatureextremes, viscous fluids and frequent start/stop cycles.Beyond just the pump, AutoPump systems offer the mostcomplete range of tubing, hose, connectors, caps andaccessories to help your installation go smoothly. Thissuperior pumping heritage, application experience andsupport back up every AutoPump you put to work onyour project.

Advantages

1. Based on the original automaticair-powered well pump, provenworldwide over 18 years

2. Competitive flow rates andpumping capabilities

3. Patented, proven design forsuperior reliability and durability

4. Handles solids, some solvents,hydrocarbons and corrosiveconditions beyond the limits ofelectric pumps

5. Two-year warranty

31

AutoPump®

Bottom Inlet, Long AP3B

AP3 AutoPumps are warranted for two (2) years:100% materials and workmanship.


Application LimitsAP3 AutoPumps are designed to handle the applicationrange described below. For applications outside thisrange, consider the AP4 and AP2 models.

Maximum Temperature: 120˚F (49˚C)pH Range: 4-9Some solvents and Fuels: gasoline, diesel fuel, BTEX, MTBE

Liquid Discharge

Inlet

Air Supply

Exhaust

O.D. 2.63" (6.68 cm)

extended screen adds 5"

Len

gth

wit

h S

tan

dar

d S

cree

n 5

2" (

132

cm)

Act

uat

ion

Lev

el 3

1" (

79 c

m)






Min. Actuation LevelAir Usage

Min. Liquid Density

Standard Construction MaterialsPump BodyPump Ends


Fitting Type

Tube OptionsTubing Material

Sizes1 - Liquid DischargePump Air Supply

Air Exhaust

1 Applies to QED supplied tubing;other tubing sources may not

conform to QED fittings.

3" - Long AP3 Bottom InletBottom2.63 in. (6.68 cm)52 in. (132 cm)57 in. (145 cm)11 lbs. (5.0 kg)7.3 gpm (27.6 lpm) - See Flow Rate Chart0.23 - 0.32 gal (0.87 - 1.21L )220 ft. (67 m)5 - 100 psi (0.4 - 7.0 kg/cm2)31 in. (79 cm)0.33-1.45 scf / gal. (2.5-10.8 liters of air /fluid liter) - See Air Usage Chart

0.7 SpG (0.7 g/cm3)

Fiberglass or Stainless SteelStainless Steel, UHMWPE2, BrassStainless Steel, Viton, Acetal, NylonBrass or Stainless SteelBarbs or Quick Connects

Nylon3/4 in. (19 mm) or 1 in. (25 mm) OD1/2 in. (13 mm) OD5/8 in. (16 mm) OD


32

AutoPump®

Bottom Inlet, LongAP3B

00

12.2400

6.120 FT.

Meters20061

18054.9

80 14012010030.5

6018.3 42.736.624.4 48.8

160

2

4

7.6

15.1

IN WELL DEPTH

FT.20018040 80 14012010060 1600 20 DEPTH

8

6

30.3

22.7

34.1910 FT. (300 cm) SUBMERGENCE OF PUMP HEAD

12.26.1 Meters9.45 1630.518.3 42.736.624.4 48.8 IN WELL

0 0

PER LITERS


12.26.1 Meters8.84 9.45 1642.736.630.524.418.30 4020

0FT.

02001801601401201008060

IN WELL DEPTH

WITH

MINUTE

PER

O.D. TUBE

19 mm

3/4-INCH

O.D. TUBE

WITH

MINUTE

APPROXIMATEGALLONS


7 26.5

5 18.9

3 11.4

1 3.8

3

1

2

6

4

5

7

9

8

11.4

3.8

7.6

22.7

15.1

18.9

26.5

34.1

30.3

3

1

2

6

4

5

7

9

8

11.4

3.8

7.6

22.7

15.1

18.9

26.5

34.1

30.3

MINUTE

3/4-INCH

O.D. TUBE

WITH

GALLONS

PER

PER

19 mm

O.D. TUBE

MINUTE

WITH

APPROXIMATE

LITERS

MINUTE

3/4-INCH

O.D. TUBE

WITH

GALLONS

PER

PER

19 mm

O.D. TUBE

MINUTE

WITH

APPROXIMATE

LITERS

AIR INLET PRESSURES

100 PSI27 Kg/cm

70 PSI25 Kg/cm3 Kg/cm 2

40 PSI

AIR INLET PRESSURES

7 Kg/cm 2100 PSI

5 Kg/cm 270 PSI40 PSI

3 Kg/cm

AIR INLET PRESSURES

7 Kg/cm 2100 PSI


3 Kg/cm 2

00

12.2400

6.120 FT.

Meters20061

18054.9

80 14012010030.5

6018.3 42.736.624.4 48.8

160

2

4

7.6

15.1

IN WELL DEPTH

FT.20018040 80 14012010060 1600 20 DEPTH

8

6

30.3

22.7


12.26.1 Meters9.45 1630.518.3 42.736.624.4 48.8 IN WELL

0 0

PER LITERS


12.26.1 Meters8.84 9.45 1642.736.630.524.418.30 4020

0FT.

02001801601401201008060

IN WELL DEPTH

WITH

MINUTE

PER

O.D. TUBE

25 mm

1-INCH

O.D. TUBE

WITH

MINUTE

APPROXIMATEGALLONS


7 26.5

5 18.9

3 11.4

1 3.8

3

1

2

6

4

5

7

9

8

11.4

3.8

7.6

22.7

15.1

18.9

26.5

34.1

30.3

3

1

2

6

4

5

7

9

8

11.4

3.8

7.6

22.7

15.1

18.9

26.5

34.1

30.3

MINUTE

1-INCH

O.D. TUBE

WITH

GALLONS

PER

PER

25 mm

O.D. TUBE

MINUTE

WITH

APPROXIMATE

LITERS

MINUTE

1-INCH

O.D. TUBE

WITH

GALLONS

PER

PER

25 mm

O.D. TUBE

MINUTE

WITH

APPROXIMATE

LITERS

AIR INLET PRESSURES

7 Kg/cm 2100 PSI


3 Kg/cm 2

AIR INLET PRESSURES

7 Kg/cm 2100 PSI


3 Kg/cm 2

AIR INLET PRESSURES

100 PSI27 Kg/cm


40 PSI

FLOW RATES MAY VARY WITH SITE CONDITIONS. CALL FOR TECHNICAL ASSISTANCE.

.75 inch (19 mm) O.D.Fluid Discharge Tubing

1.00 inch (25 mm) O.D.Fluid Discharge Tubing


Flow Rates1

33

AutoPump®


.2

.3

.4

.5

.6

.7

.8

.9

20 40 60 80 100 120 140 160 180 200

1.1

1.0

1.2

1.3

1.4

1.5

1.6

STANDARDCUBIC FEET OF AIRPERGALLON PUMPED(SCF/GAL)

MetersFT.

36.61.6 2.21 3.81 24.4 30.5 169.457.24 8.84



PER

2.2

1.5

3.0

3.7

5.2

4.5

6.0

7.5

6.7

8.2

9.0

10.5

9.7

11.2

12

APPROXIMATE

IN WELL DEPTH

40 PSI23 Kg/cm

70 PSI5 Kg/cm 2

100 PSI7 Kg/cm 2

.2

.3

.4

.5

.6

.7

.8

.9

20 40 60 80 100 120 140 160 180 200

1.1

1.0

1.2

1.3

1.4

1.5

1.6

MetersFT.

36.61.6 2.21 3.81 24.4 30.5 169.457.24 8.84



PER

2.2

1.5

3.0

3.7

5.2

4.5

6.0

7.5

6.7

8.2

9.0

10.5

9.7

11.2

12

APPROXIMATE

IN WELL DEPTH

STANDARDCUBIC FEET OF AIRPERGALLON PUMPED(SCF/GAL)

40 PSI23 Kg/cm

70 PSI5 Kg/cm 2

100 PSI7 Kg/cm 2

Air Consumption



34

AutoPump®

Bottom Inlet, ShortAP3BDescription

Max. Flow

O.D.

Length

6.0 gpm (22.7 lpm)

2.63 in (6.68 cm)

42 in. (106.6 cm)

The AP3 Bottom Inlet Short AutoPump is designed formoderate-duty remediation pumping applications with wellcasings 3” (75 mm) diameter and larger. It is designed forwells having shorter water columns and/or the need topump down to lower water levels, compared to full-lengthpumps. Complete system components such as tubing andhose sets, well caps, and flow counters are available for theAP3 Long Bottom Inlet AutoPump. Call QED for prompt, no-obligation assistance on your pumping project needs.

The AutoPump HeritageThe AP3 Bottom Inlet Short AutoPump is part of thefamous AutoPump family of original automatic air-poweredpumps, developed in the mid 1980s specifically to handleunique pumping needs at remediation and landfill sites.Over the years they’ve proven their durability at thousandsof sites worldwide. AutoPumps are designed to handledifficult pumping challenges that other pumps can’t, suchas solvents, suspended solids, corrosives, temperatureextremes, viscous fluids and frequent start/stop cycles.Beyond just the pump, AutoPump systems offer the mostcomplete range of tubing, hose, connectors, caps andaccessories to help your installation go smoothly. Thissuperior pumping heritage, application experience andsupport back up every AutoPump you put to work onyour project.

Advantages






35

AutoPump®

Bottom Inlet, Short AP3BPump Dimensions Specifications & Operating Requirements


Inlet

Air Supply

Exhaust

O.D. 2.63" (6.68 cm)

extended screen adds 5"

Liquid Discharge

Len

gth

wit

h S

tan

dar

d S

cree

n 4

2" (

107

cm)

Act

uat

ion

Lev

el 2

2" (

55.9

cm

)Model

Liquid Inlet LocationOD

Length Overall (pump & fittings)Length Overall, w / Extended Screen




Air Usage

Min. Liquid Density



Fitting Type



Air Exhaust



3" - Short AP3 Bottom InletBottom2.63 in. (6.68 cm)42 in. (107cm)47 in. (117cm)10 lbs. (4.5 kg)6.0 gpm (22.7 lpm) - See Flow Rate Chart0.08 - 0.15 gal (.30 - 0.57L )175 ft. (53.3 m)5 -80 psi (0.4 - 5.6 kg/cm2)22 in. (56 cm)0.35 - 1.6 scf / gal. (2.6-12.0 liters of air /fluid liter) - See Air Usage Chart

0.7 SpG (0.7 g/cm3)

Fiberglass or Stainless SteelStainless Steel, UHMWPE*, BrassStainless Steel, Viton, Acetal, NylonBrass or Stainless SteelBarbs or Quick Connects



Application LimitsAP3 AutoPumps are designed to handle the applicationranges described below. For applications outside thisrange, consider the AP4 and AP2 models.

Maximum Temperature: 120˚F (49˚C)pH Range: 4-9Solvents and Fuels: gasoline, diesel fuel, BTEX, MTBE

36

AutoPump®

Bottom Inlet, ShortAP3B


00

12.2400

6.120 FT.

Meters20061

18054.9

80 14012010030.5

6018.3 42.736.624.4 48.8

160

2

4

7.6

15.1

IN WELLDEPTH

FT.20018040 80 14012010060 1600 20 DEPTH

8

6

30.3

22.7


12.26.1 Meters9.45 1630.518.3 42.736.624.4 48.8 IN WELL

0 0

PER LITERS


12.26.1 Meters8.84 9.45 1642.736.630.524.418.30 4020

0FT.

02001801601401201008060

IN WELLDEPTH

WITH

MINUTE

PER

O.D. TUBE

25 mm

1-INCH

O.D. TUBE

WITH

MINUTE

APPROXIMATEGALLONS


7 26.5

5 18.9

3 11.4

1 3.8

3

1

2

6

4

5

7

9

8

11.4

3.8

7.6

22.7

15.1

18.9

26.5

34.1

30.3

3

1

2

6

4

5

7

9

8

11.4

3.8

7.6

22.7

15.1

18.9

26.5

34.1

30.3

MINUTE

1-INCH

O.D. TUBE

WITH

GALLONS

PER

PER

25 mm

O.D. TUBE

MINUTE

WITH

APPROXIMATE

LITERS

MINUTE

1-INCH

O.D. TUBE

WITH

GALLONS

PER

PER

25 mm

O.D. TUBE

MINUTE

WITH

APPROXIMATE

LITERS

AIR INLET PRESSURES

25.7 Kg/cm80 PSI

3 Kg/cm 240 PSI

AIR INLET PRESSURES

80 PSI25.7 Kg/cm

40 PSI3 Kg/cm 2

AIR INLET PRESSURES

25.7 Kg/cm80 PSI40 PSI

3 Kg/cm 2

00

12.2400

6.120 FT.

Meters20061

18054.9

80 14012010030.5

6018.3 42.736.624.4 48.8

160

2

4

7.6

15.1

IN WELL DEPTH

FT.20018040 80 14012010060 1600 20 DEPTH

8

6

30.3

22.7

34.19


12.26.1 Meters9.45 1630.518.3 42.736.624.4 48.8 IN WELL

0 0

PER LITERS


12.26.1 Meters8.84 9.45 1642.736.630.524.418.30 4020

0FT.

02001801601401201008060

IN WELL DEPTH

WITH

MINUTE

PER

O.D. TUBE

19 mm

3/4-INCH

O.D. TUBE

WITH

MINUTE

APPROXIMATEGALLONS


7 26.5

5 18.9

3 11.4

1 3.8

3

1

2

6

4

5

7

9

8

11.4

3.8

7.6

22.7

15.1

18.9

26.5

34.1

30.3

3

1

2

6

4

5

7

9

8

11.4

3.8

7.6

22.7

15.1

18.9

26.5

34.1

30.3

MINUTE

3/4-INCH

O.D. TUBE

WITH

GALLONS

PER

PER

19 mm

O.D. TUBE

MINUTE

WITH

APPROXIMATE

LITERS

MINUTE

3/4-INCH

O.D. TUBE

WITH

GALLONS

PER

PER

19 mm

O.D. TUBE

MINUTE

WITH

APPROXIMATE

LITERS

3 Kg/cm 240 PSI 25.7 Kg/cm

80 PSI

AIR INLET PRESSURES

AIR INLET PRESSURES

80 PSI25.7 Kg/cm

40 PSI3 Kg/cm 2

AIR INLET PRESSURES

40 PSI3 Kg/cm 2

25.7 Kg/cm80 PSI




Flow Rates1

37

AutoPump®

Bottom Inlet, Short AP3B

.2

.3

.4

.5

.6

.7

.8

.9

20 40 60 80 100 120 140 160 180 200

1.1

1.0

1.2

STANDARDCUBIC FEET OF AIRPERGALLON PUMPED

1.3

1.4

1.5

1.6

(SCF/GAL)

MetersFT.

36.61.6 2.21 3.81 24.4 30.5 169.457.24 8.84



PER

2.2

1.5

3.0

3.7

5.2

4.5

6.0

7.5

6.7

8.2

9.0

10.5

9.7

11.2

12

APPROXIMATE

IN WELL DEPTH

1.8 13.5

40 PSI23 Kg/cm

80 PSI5.7 Kg/cm 2

.2

.3

.4

.5

.6

.7

.8

.9

20 40 60 80 100 120 140 160 180 200

1.1

1.0

1.2


1.3

1.4

1.5

1.6

(SCF/GAL)

MetersFT.

36.61.6 2.21 3.81 24.4 30.5 169.457.24 8.84



PER

2.2

1.5

3.0

3.7

5.2

4.5

6.0

7.5

6.7

8.2

9.0

10.5

9.7

11.2

12

APPROXIMATE

IN WELL DEPTH

1.7 12.7

40 PSI23 Kg/cm

80 PSI5.7 Kg/cm 2

Air Consumption



38

AutoPump®

Top Inlet, LongAP3TMax. Flow

O.D.

Optional O.D.

Length

5.4 gpm (20 lpm)

3.4 in (8.64 cm)

2.6 in (6.68 cm)

57 in. (145 cm)

Description

The AP3T Top Inlet Long AutoPump is designed for moder-ate-duty remediation pumping applications with wellcasings 3” (7.62 cm) diameter and larger using available2.63 inch (6.68 cm) inlet. It is designed for applicationsrequiring an elevated inlet, such as pumping total fluidsfrom wells contaminated with LNAPLs. Call QED forprompt, no-obligation assistance on your pumping projectneeds.

The AutoPump HeritageThe AP3T Top Inlet Long AutoPump is part of the famousAutoPump family of original automatic air-powered pumps,developed in the mid 1980s specifically to handle uniquepumping needs at remediation and landfill sites. Over theyears they’ve proven their durability at thousands of sitesworldwide. AutoPumps are designed to handle difficultpumping challenges that other pumps can’t, such assolvents, suspended solids, corrosives, temperatureextremes, viscous fluids and frequent start/stop cycles.Beyond just the pump, AutoPump systems offer the mostcomplete range of tubing, hose, connectors, caps andaccessories to help your installation go smoothly. Thissuperior pumping heritage, application experience andsupport back up every AutoPump you put to work onyour project.

Advantages






39

AutoPump®

Top Inlet, Long AP3TPump Dimensions Specifications & Operating Requirements


Body O.D. 2.63" (6.68 cm)

Inlet O.D. 3.4" (8.64 cm)Also Available (2.63" (6.68 cm)

Inlet

Air Supply

Exhaust

Liquid Discharge

Len

gth

to

To

p o

f F

itti

ng

s 5

7" (

145

cm)

Act

uat

ion

Lev

el 5

3" (

135

cm)






Air Usage

Min. Liquid Density



Fitting Type



Air Exhaust



3" - Long AP3 Top InletTop3.4 in. (8.64 cm) (2.63 in. Available)57 in. (145 cm)11.5 lbs. (5.3 kg)5.4 gpm (20.4 lpm) - See Flow Rate Chart0.23 - 0.32 gal (0.87 - 1.21L )220 ft. (67 m)5 - 100 psi (0.4 - 7.0 kg/cm2)53 in. (135 cm)0.41 -1.59 scf / gal.(3.0 - 11.9 liters of air /fluid liter) - See Air Usage Chart

0.7 SpG (0.7 g/cm3)

Fiberglass or Stainless SteelStainless Steel, Acetal, BrassStainless Steel, Viton, Acetal, NylonBrass or Stainless SteelBarbs or Quick Connects




40

AutoPump®

Top Inlet, LongAP3T


00

12.2400

6.120 FT.

Meters20061

18054.9

80 14012010030.5

6018.3 42.736.624.4 48.8

160

2

4

7.6

15.1

IN WELLDEPTH

FT.20018040 80 14012010060 1600 20 DEPTH

8

6

30.3

22.7


12.26.1 Meters9.45 1630.518.3 42.736.624.4 48.8 IN WELL

0 0

PER LITERS


12.26.1 Meters8.84 9.45 1642.736.630.524.418.30 4020

0FT.

02001801601401201008060

IN WELLDEPTH

WITH

MINUTE

PER

O.D. TUBE

25 mm

1-INCH

O.D. TUBE

WITH

MINUTE

APPROXIMATEGALLONS


7 26.5

5 18.9

3 11.4

1 3.8

3

1

2

6

4

5

7

9

8

11.4

3.8

7.6

22.7

15.1

18.9

26.5

34.1

30.3

3

1

2

6

4

5

7

9

8

11.4

3.8

7.6

22.7

15.1

18.9

26.5

34.1

30.3

MINUTE

1-INCH

O.D. TUBE

WITH

GALLONS

PER

PER

25 mm

O.D. TUBE

MINUTE

WITH

APPROXIMATE

LITERS

MINUTE

1-INCH

O.D. TUBE

WITH

GALLONS

PER

PER

25 mm

O.D. TUBE

MINUTE

WITH

APPROXIMATE

LITERS

AIR INLET PRESSURES

100 PSI27 Kg/cm


40 PSI

AIR INLET PRESSURES

7 Kg/cm 2100 PSI

5 Kg/cm 270 PSI

40 PSI3 Kg/cm 2

AIR INLET PRESSURES

7 Kg/cm 2100 PSI

25 Kg/cm70 PSI

40 PSI3 Kg/cm 2

00

12.2400

6.120 FT.

Meters20061

18054.9

80 14012010030.5

6018.3 42.736.624.4 48.8

160

2

4

7.6

15.1

IN WELL DEPTH

FT.20018040 80 14012010060 1600 20 DEPTH

8

6

30.3

22.7


12.26.1 Meters9.45 1630.518.3 42.736.624.4 48.8 IN WELL

0 0

PER LITERS


12.26.1 Meters8.84 9.45 1642.736.630.524.418.30 4020

0FT.

02001801601401201008060

IN WELL DEPTH

WITH

MINUTE

PER

O.D. TUBE

19 mm

3/4-INCH

I.D. TUBE

WITH

MINUTE

APPROXIMATEGALLONS


7 26.5

5 18.9

3 11.4

1 3.8

3

1

2

6

4

5

7

9

8

11.4

3.8

7.6

22.7

15.1

18.9

26.5

34.1

30.3

3

1

2

6

4

5

7

9

8

11.4

3.8

7.6

22.7

15.1

18.9

26.5

34.1

30.3

MINUTE

3/4-INCH

I.D. TUBE

WITH

GALLONS

PER

PER

19 mm

O.D. TUBE

MINUTE

WITH

APPROXIMATE

LITERS

MINUTE

3/4-INCH

I.D. TUBE

WITH

GALLONS

PER

PER

19 mm

O.D. TUBE

MINUTE

WITH

APPROXIMATE

LITERS

O.D. TUBE

AIR INLET PRESSURES

100 PSI27 Kg/cm


40 PSI

AIR INLET PRESSURES

7 Kg/cm 2100 PSI


3 Kg/cm 2

AIR INLET PRESSURES

7 Kg/cm 2100 PSI

25 Kg/cm70 PSI

40 PSI3 Kg/cm 2




Flow Rates1

41

AutoPump®

Top Inlet, Long AP3T

.2

.3

.4

.5

.6

.7

.8

.9

20 40 60 80 100 120 140 160 180 200

1.1

1.0

1.2


1.3

1.4

1.5

1.6

(SCF/GAL)

MetersFT.

36.61.6 2.21 3.81 24.4 30.5 169.457.24 8.84



PER

2.2

1.5

3.0

3.7

5.2

4.5

6.0

7.5

6.7

8.2

9.0

10.5

9.7

11.2

12

APPROXIMATE

IN WELL DEPTH

100 PSI7 Kg/cm 2

70 PSI5 Kg/cm 2

40 PSI23 Kg/cm

.2

.3

.4

.5

.6

.7

.8

.9

20 40 60 80 100 120 140 160 180 200

1.1

1.0

1.2


1.3

1.4

1.5

1.6

(SCF/GAL)

MetersFT.

36.61.6 2.21 3.81 24.4 30.5 169.457.24 8.84



PER

2.2

1.5

3.0

3.7

5.2

4.5

6.0

7.5

6.7

8.2

9.0

10.5

9.7

11.2

12

APPROXIMATE

IN WELL DEPTH

100 PSI7 Kg/cm 2

70 PSI5 Kg/cm 2

40 PSI23 Kg/cm

Air Consumption



42

AutoPump®

Top Inlet, ShortAP3TDescription

Max. Flow

O.D.

Length

4.8 gpm (18.1 lpm)

3.4 in (8.64 cm)

47 in. (119 cm)

The AP3T Top Inlet Short AutoPump is designed formoderate-duty remediation pumping applications with wellcasings 3” (7.62 cm) diameter and larger using available2.63 inch (6.68 cm) inlet. It is designed for applicationsrequiring an elevated inlet, such as pumping total fluidsfrom wells contaminated with LNAPLs. Call QED forprompt, no-obligation assistance on your pumping projectneeds.

The AutoPump HeritageThe AP3T Top Inlet Short AutoPump is part of the famousAutoPump family of original automatic air-powered pumps,developed in the mid 1980s specifically to handle uniquepumping needs at remediation and landfill sites. Over theyears they’ve proven their durability at thousands of sitesworldwide. AutoPumps are designed to handle difficultpumping challenges that other pumps can’t, such assolvents, suspended solids, corrosives, temperatureextremes, viscous fluids and frequent start/stop cycles.Beyond just the pump, AutoPump systems offer the mostcomplete range of tubing, hose, connectors, caps andaccessories to help your installation go smoothly. Thissuperior pumping heritage, application experience andsupport back up every AutoPump you put to work onyour project.

Advantages






43

AutoPump®

Top Inlet, Short AP3TPump Dimensions Specifications & Operating Requirements


Body O.D. 2.63" (6.68 cm)

Inlet

Air Supply

Exhaust3/8" (9 mm) O.D.

Liquid Discharge

Len

gth

to

To

p o

f F

itti

ng

s 4

7" (

119

cm)

Act

uat

ion

Lev

el 4

2" (

107

cm)

Inlet O.D. 3.4" (8.64 cm)Also Available 2.63" (6.68 cm)






Air Usage

Min. Liquid Density



Fitting Type



Air Exhaust



3" - Short AP3 Top InletTop3.4 in. (8.64 cm) (2.63 in. Available)47 in. (119 cm)10 lbs. (4.5 kg)4.8 gpm (18.1 lpm) - See Flow Rate Chart0.08 - 0.15 gal (.30 - 0.57L )175 ft. (53.3 m)5 -80 psi (0.4 - 5.6 kg/cm2)42 in. (107 cm)0.43 -1.6 scf / gal.(3.2 - 12.0 liters of air /fluid liter) - See Air Usage Chart

0.7 SpG (0.7 g/cm3)

Fiberglass or Stainless SteelStainless Steel, Acetal, HDPE, BrassStainless Steel, Viton, Acetal, NylonBrass or Stainless SteelBarbs or Quick Connects




44

AutoPump®

Top Inlet, ShortAP3T


00

12.2400

6.120 FT.

Meters20061

18054.9

80 14012010030.5

6018.3 42.736.624.4 48.8

160

2

4

7.6

15.1

IN WELLDEPTH

FT.20018040 80 14012010060 1600 20 DEPTH

8

6

30.3

22.7


12.26.1 Meters9.45 1630.518.3 42.736.624.4 48.8 IN WELL

0 0

PER LITERS


12.26.1 Meters8.84 9.45 1642.736.630.524.418.30 4020

0FT.

02001801601401201008060

IN WELLDEPTH

WITH

MINUTE

PER

O.D. TUBE

25 mm

1-INCH

O.D. TUBE

WITH

MINUTE

APPROXIMATEGALLONS


7 26.5

5 18.9

3 11.4

1 3.8

3

1

2

6

4

5

7

9

8

11.4

3.8

7.6

22.7

15.1

18.9

26.5

34.1

30.3

3

1

2

6

4

5

7

9

8

11.4

3.8

7.6

22.7

15.1

18.9

26.5

34.1

30.3

MINUTE

1-INCH

O.D. TUBE

WITH

GALLONS

PER

PER

25 mm

O.D. TUBE

MINUTE

WITH

APPROXIMATE

LITERS

MINUTE

1-INCH

O.D. TUBE

WITH

GALLONS

PER

PER

25 mm

O.D. TUBE

MINUTE

WITH

APPROXIMATE

LITERS

40 PSI3 Kg/cm 2

25.7 Kg/cm80 PSI

AIR INLET PRESSURES

80 PSI25.7 Kg/cm

40 PSI3 Kg/cm 2

AIR INLET PRESSURES

25.7 Kg/cm80 PSI

3 Kg/cm 240 PSI

AIR INLET PRESSURES

00

12.2400

6.120 FT.

Meters20061

18054.9

80 14012010030.5

6018.3 42.736.624.4 48.8

160

2

4

7.6

15.1

IN WELL DEPTH

FT.20018040 80 14012010060 1600 20 DEPTH

8

6

30.3

22.7

34.19


12.26.1 Meters9.45 1630.518.3 42.736.624.4 48.8 IN WELL

0 0

PER LITERS


12.26.1 Meters8.84 9.45 1642.736.630.524.418.30 4020

0FT.

02001801601401201008060

IN WELL DEPTH

WITH

MINUTE

PER

O.D. TUBE

19 mm

3/4-INCH

O.D. TUBE

WITH

MINUTE

APPROXIMATEGALLONS


7 26.5

5 18.9

3 11.4

1 3.8

3

1

2

6

4

5

7

9

8

11.4

3.8

7.6

22.7

15.1

18.9

26.5

34.1

30.3

3

1

2

6

4

5

7

9

8

11.4

3.8

7.6

22.7

15.1

18.9

26.5

34.1

30.3

5 7 Kg/cm

MINUTE

3/4-INCH

O.D. TUBE

WITH

GALLONS

PER

PER

19 mm

O.D. TUBE

MINUTE

WITH

APPROXIMATE

LITERS

MINUTE

3/4-INCH

O.D. TUBE

WITH

GALLONS

PERPER

19 mm

O.D. TUBE

MINUTE

WITH

APPROXIMATE

LITERS

280 PSI

40 PSI3 Kg/cm 2

AIR INLET PRESSURES

80 PSI25.7 Kg/cm

40 PSI3 Kg/cm 2

AIR INLET PRESSURES

3 Kg/cm 240 PSI 25.7 Kg/cm

80 PSI

AIR INLET PRESSURES




Flow Rates1

45

AutoPump®

Top Inlet, Short AP3T

.2

.3

.4

.5

.6

.7

.8

.9

20 40 60 80 100 120 140 160 180 200

1.1

1.0

1.2


1.3

1.4

1.5

1.6

(SCF/GAL)

MetersFT.

36.61.6 2.21 3.81 24.4 30.5 169.457.24 8.84



PER

2.2

1.5

3.0

3.7

5.2

4.5

6.0

7.5

6.7

8.2

9.0

10.5

9.7

11.2

12

APPROXIMATE

IN WELL DEPTH

1.7 12.7

40 PSI23 Kg/cm

80 PSI5.7 Kg/cm 2

.2

.3

.4

.5

.6

.7

.8

.9

20 40 60 80 100 120 140 160 180 200

1.1

1.0

1.2


1.3

1.4

1.5

1.6

(SCF/GAL)

80 PSI

MetersFT.

36.61.6 2.21 3.81 24.4 30.5 169.457.24 8.84



PER

2.2

1.5

3.0

3.7

5.2

4.5

6.0

7.5

6.7

8.2

9.0

10.5

9.7

11.2

12

APPROXIMATE

5.7 Kg/cm 2

IN WELL DEPTH

1.8 13.5

40 PSI23 Kg/cm

Air Consumption



46

AutoPump®

Bottom Inlet, LongAP2BDescription

Max. Flow

O.D.

Length

2.3 gpm (8.8 lpm)

1.75 in (4.45 cm)

55 in. (139 cm)

The AP2 Bottom Inlet Long AutoPump provides maximumcapabilities and flow in a bottom inlet pump for 2” (50 mm)diameter wells. It is offered in optional versions to handleeven severe remediation and landfill pumping applications,and delivers flow rates up to 2.3 gpm (8.8 lpm). The AP2Long Bottom Inlet AutoPump is complemented by the mostcomprehensive selection of accessories to provide acomplete system to meet site-specific requirements. CallQED for prompt, no-obligation assistance on your pumpingproject needs.

The AutoPump HeritageThe AP2 Bottom Inlet Long AutoPump is part of the famousAutoPump family of original automatic air-powered pumps,developed in the mid 1980s specifically to handle uniquepumping needs at remediation and landfill sites. Over theyears they’ve proven their durability at thousands of sitesworldwide. AutoPumps are designed to handle difficultpumping challenges that other pumps can’t, such assolvents, suspended solids, corrosives, temperatureextremes, viscous fluids and frequent start/stop cycles.Beyond just the pump, AutoPump systems offer the mostcomplete range of tubing, hose, connectors, caps andaccessories to help your installation go smoothly. Thissuperior pumping heritage, application experience andsupport back up every AutoPump you put to work onyour project.

Advantages1. The original 2” automatic air-

powered well pump, provenworldwide over 15 years

2. The industry leader in reliability,durability, flow rate and depthcapability in an automatic pumpfor 2-inch wells

3. Handles solids, hyrocarbons,solvents, corrosive conditions,viscous fluids and landfill liquids


47

AutoPump®


AP2 AutoPumps are warranted for one (1) year:100% materials and workmanship.


Application Limits (base model)Base model AP2 AutoPumps are designed to handlethe application ranges described below. Forapplications outside this range, consult QEDabout AP2 upgrades.

Maximum Temperature: 150˚F (65˚C)pH Range: 4-9Solvents and Fuels: diesel, gasoline, JP1-JP6,#2 heating oils, BTEX, MTBE, landfill liquids

Liquid Discharge

Inlet

Air Supply

Exhaust

O.D. 1.75" (4.45 cm)

Act

uat

ion

Lev

el 3

5" (

88.9

cm

)

Len

gth

Ove

rall,

wit

h S

cree

n 5

5" (

140

cm)







Min. Liquid Density


Pump BodyPump Ends


Fitting Type

Tube & Hose OptionsTubing Material




Air Exhaust



2" - Long AP2 Bottom InletBottom1.75 in. (4.45 cm)55 in. (139 cm)57 in. (144 cm)7.8 lb (3.6 Kg)2.3 gpm (8.8 lpm) - See Flow Rate Chart0.14 - 0.17gal (0.53 - 0.64 L)300 ft (91.4 m)5 - 130 psi (0.4 - 9.2 kg/cm2)35 in. (88.9 cm)0.38 -1.45 scf / gal. (2.8 - 10.8 liters of air / fluid liter)See Air Usage Chart

0.7 SpG (0.7 g/cm3)

Stainless SteelStainless SteelStainless Steel, Viton, PVDF3


Nylon5/8 in. (16 mm) OD3/8 in. (9.5 mm) OD1/2 in. (13 mm) ODNitrile1/2 in. (13 mm) ID1/4 in (6.4 mm) ID3/8 in. (9.5 mm) ID


48

AutoPump®

Bottom Inlet, LongAP2B

00

12.2400

6.120 FT.

Meters20061

18054.9

80 14012010030.5

6018.3 42.736.624.4 48.8

160

2 7.6

FT.20018040 80 14012010060 1600 20 DEPTH


12.26.1 Meters9.45 1630.518.3 42.736.624.4 48.8 IN WELL

DEPTH IN WELL

0 0

PER LITERS


12.26.1 Meters8.84 9.45 1642.736.630.524.418.30 4020

0FT.

02001801601401201008060

IN WELL DEPTH

WITH

MINUTE

PER

I.D. HOSE

13 mm

1/2-INCH

I.D. HOSE

WITH

MINUTE

APPROXIMATEGALLONS


4 15.1

3 11.4

1 3.8

3.8

7.6

15.1

11.4

1

2

4

3

3.8

7.6

15.1

11.4

1

2

4

3

1/2-INCH

I.D. HOSE

MINUTE

WITH

GALLONS

PER

13 mm

I.D. HOSE

PER

MINUTE

WITH

APPROXIMATE

LITERS

1/2-INCH

I.D. HOSE

MINUTE

WITH

GALLONS

PER

13 mm

I.D. HOSE

PER

MINUTE

WITH

APPROXIMATE

LITERSAIR INLET PRESSURES

7 Kg/cm 2100 PSI


3 Kg/cm 2

40 PSI3 Kg/cm 2

5 Kg/cm 270 PSI

7 Kg/cm 2100 PSI

AIR INLET PRESSURES

100 PSI27 Kg/cm

70 PSI25 Kg/cm

40 PSI3 Kg/cm 2

AIR INLET PRESSURES

1/2 inch (13 mm)Inside Diameter Discharge Hose(Equivalent to 5/8-Inch O.D. Tubing)


Flow Rates1

49

AutoPump®

Bottom Inlet, Long AP2BAir Consumption

IN WELL DEPTH

.2

.3

.4

.5

.6

.7

.8

.9

20 40 60 80 100 120 140 160 180 200

1.1

1.0

1.2


1.3

1.4

1.5

1.6

(SCF/GAL)

MetersFT.

36.61.6 2.21 3.81 24.4 30.5 169.457.24 8.84



PER

2.2

1.5

3.0

3.7

5.2

4.5

6.0

7.5

6.7

8.2

9.0

10.5

9.7

11.2

12

APPROXIMATE

40 PSI23 Kg/cm

70 PSI5 Kg/cm 2

7 Kg/cm100 PSI

2


50

AutoPump®

Bottom Inlet, ShortAP2BDescription

Max. Flow

O.D.

Length

2.0 gpm (7.6 lpm)

1.75 in (4.45 cm)

33 in. (85 cm)

The AP2 Bottom Inlet Short AutoPump provides maximumcapabilities and flow in a bottom inlet pump for 2” (50 mm)diameter wells. It is offered in optional versions to handleeven severe remediation and landfill pumping applications,and delivers flow rates up to 2.0 gpm (7.6 lpm). The AP2Short Bottom Inlet AutoPump is complemented by the mostcomprehensive selection of accessories to provide acomplete system to meet site-specific requirements. CallQED for prompt, no-obligation assistance on your pumpingproject needs.

The AutoPump HeritageThe AP2 Bottom Inlet Short AutoPump is part of thefamous AutoPump family of original automatic air-poweredpumps, developed in the mid 1980s specifically to handleunique pumping needs at remediation and landfill sites.Over the years they’ve proven their durability at thousandsof sites worldwide. AutoPumps are designed to handledifficult pumping challenges that other pumps can’t, suchas solvents, suspended solids, corrosives, temperatureextremes, viscous fluids and frequent start/stop cycles.Beyond just the pump, AutoPump systems offer the mostcomplete range of tubing, hose, connectors, caps andaccessories to help your installation go smoothly. Thissuperior pumping heritage, application experience andsupport back up every AutoPump you put to workon your project.






51

AutoPump®

Bottom Inlet, Short AP2BPump Dimensions Specifications & Operating Requirements


Liquid Discharge

Inlet

Air Supply

Exhaust

O.D. 1.75" (4.45 cm)

Act

uat

ion

Lev

el 2

0" (

51 c

m)

Len

gth

Ove

rall,

wit

h S

cree

n 3

3" (

84 c

m)







Min. Liquid Density


Pump BodyPump Ends


Fitting Type





Air Exhaust



2" - Short AP2 Bottom InletBottom1.75 in. (4.45 cm)33 in (85 cm)35. in (89cm)5.4 lb (3.6 Kg)2.0 gpm (7.6 lpm)0.05 - 0.08 gal (0.19 - 0.30 L)300 ft (91.4 m)5 - 130 psi (0.4 - 9.2 kg/cm2)20 in. (51 cm).39-2.58 scf/gal (2.9-19.3 liters of air/fluid litersee air usage chart0.7 SpG (0.7 g/cm3)







52

AutoPump®

Bottom Inlet, ShortAP2B

IN WELL 48.824.4 36.6 42.718.3 30.5 54.9 61 Meters6.1 12.2200

060 80200 40 160100 120 140 180

1

0DEPTH FT.

I.D. HOSE3.8

WITH

1/2-INCH

I.D. HOSE

2

MINUTE

PER 3

MINUTE

13 mm

WITH7.6

PER

LITERS11.4


4

GALLONS

15.1

APPROXIMATE

1 3.8

61200

0

30.524.418.36.1 12.2 48.836.6 42.7 54.9200 60 8040 160100 120 140 180

0

IN WELL MetersDEPTH FT.

1/2-INCH

I.D. HOSE

WITH

MINUTE

2 WITH

13 mm

I.D. HOSE

MINUTE7.6

PER

PER

GALLONS

3

4

LITERS11.4APPROXIMATE

15.1

20061


030.518.3 24.46.1 12.2 36.6 42.7 48.8 54.9

60 800

20 40 100 120 140 160 180IN WELL MetersDEPTH

0FT.

I.D. HOSE

1

1/2-INCH

WITH2

13 mm

3.8 I.D. HOSE

7.6 WITH

MINUTE

GALLONS

MINUTE

PER 3

4

APPROXIMATE

PER

11.4 LITERS

15.1


3 Kg/cm40 PSI

2

5 Kg/cm 270 PSI

27 Kg/cm100 PSI

AIR INLET PRESSURES

3 Kg/cm 240 PSI

5 Kg/cm70 PSI

2

7 Kg/cm 2100 PSI

AIR INLET PRESSURES

100 PSI27 Kg/cm

5 Kg/cm70 PSI

2

40 PSI23 Kg/cm

AIR INLET PRESSURES



Flow Rates1

53

AutoPump®

Bottom Inlet, Short AP2B

121.6(SCF/GAL)

IN WELL DEPTH 80

24.41.6 2.21 3.81

.3

.26020 40

.4

.5

.8

.7

.6

.9

1.0

1.2

1.1

1.3

1.4

1.5

Meters5.03 6.63 169.457.24 8.84

2.2

1.5160100 120 140 FT.180 200

3.0

3.7

6.0

5.2

4.5

6.7

7.5

9.0

8.2

9.7

(STD L/LITER)

10.5

11.2

2.6

2.1

CUBIC FEET OF AIR

1.7GALLON PUMPEDPER

1.8

STANDARD 1.9

2.0

2.2

2.3

2.4

2.5

2.7

2.8

19.4

15.7

LITER OF AIRPERLITER PUMPED

12.7

13.5STANDARDAPPROXIMATE

14.2

15

16.5

17.2

18.0

18.7

20.2

20.9

7 Kg/cm100 PSI

2

5 Kg/cm70 PSI

2

40 PSI3 Kg/cm 2

Air Consumption


54

AutoPump®

Top Inlet, LongAP2TDescription

Max. Flow

O.D.

Length

1.9 gpm (7.2 lpm)

1.75 in (4.45 cm)

57 in. (144 cm)

The AP2 Top Inlet Long AutoPump provides maximumcapabilities and flow in a top inlet pump for 2” (50 mm)diameter wells requiring an elevated inlet, such as pumpingtotal fluids from wells contaminated with LNAPLs. It isoffered in optional versions to handle even severeremediation and landfill pumping applications, and deliversflow rates up to 1.9 gpm (7.2 lpm). The AP2 Long BottomInlet AutoPump is complemented by the most comprehen-sive selection of accessories to provide a complete systemto meet site-specific requirements. Call QED for prompt,no-obligation assistance on your pumping project needs.

The AutoPump HeritageThe AP2 Top Inlet Long AutoPump is part of the famousAutoPump family of original automatic air-powered pumps,developed in the mid 1980s specifically to handle uniquepumping needs at remediation and landfill sites. Over theyears they’ve proven their durability at thousands of sitesworldwide. AutoPumps are designed to handle difficultpumping challenges that other pumps can’t, such assolvents, suspended solids, corrosives, temperatureextremes, viscous fluids and frequent start/stop cycles.Beyond just the pump, AutoPump systems offer the mostcomplete range of tubing, hose, connectors, caps andaccessories to help your installation go smoothly. Thissuperior pumping heritage, application experience andsupport back up every AutoPump you put to work onyour project.






55

AutoPump®

Top Inlet, Long AP2TPump Dimensions Specifications & Operating Requirements


O.D. 1.75" (4.45 cm)

Liquid Discharge

Inlet

Air Supply

Exhaust

Len

gth

to

To

p o

f F

itti

ng

s 5

7" (

144

cm)

Act

uat

ion

Lev

el 5

2" (

132

cm)






Air Usage

Min. Liquid Density


Pump BodyPump Ends


Fitting Type





Air Exhaust



2" - Long AP2 Top InletTop1.75 in. (4.45 cm)57 in. (144 cm)7.8 lbs. (3.6 kg)1.9 gpm (7.2 lpm) - See Flow Rate Chart0.14 - 0.17 gal (0.53 - 0.64l)300 ft (91.4 m)5 - 130 psi (0.4 - 9.2 kg/cm2)52 in. (132 cm)0.38 -1.57 scf / gal.(2.8 - 11.7 liters of air /fluid liter) - See Air Usage Chart

0.7 SpG (0.7 g/cm3)







56

AutoPump®

Top Inlet, LongAP2T

00

12.2400

6.120 FT.

Meters20061

18054.9

80 14012010030.5

6018.3 42.736.624.4 48.8

160

2 7.6

IN WELL DEPTH

FT.20018040 80 14012010060 1600 20 DEPTH


12.26.1 Meters9.45 1630.518.3 42.736.624.4 48.8 IN WELL

0 0

PER LITERS


12.26.1 Meters8.84 9.45 1642.736.630.524.418.30 4020

0FT.

02001801601401201008060

IN WELL DEPTH

WITH

MINUTE

PER

I.D. HOSE

13 mm

1/2-INCH

I.D. HOSE

WITH

MINUTE

APPROXIMATEGALLONS


4 15.1

3 11.4

1 3.8

3.8

7.6

15.1

11.4

1

2

4

3

3.8

7.6

15.1

11.4

1

2

4

3

1/2-INCH

I.D. HOSE

MINUTE

WITH

GALLONS

PER

13 mm

I.D. HOSE

PER

MINUTE

WITH

APPROXIMATE

LITERS

1/2-INCH

I.D. HOSE

MINUTE

WITH

GALLONS

PER

13 mm

I.D. HOSE

PER

MINUTE

WITH

APPROXIMATE

LITERSAIR INLET PRESSURES

7 Kg/cm 2100 PSI


3 Kg/cm 2

AIR INLET PRESSURES

7 Kg/cm 2100 PSI

5 Kg/cm 270 PSI

40 PSI3 Kg/cm 2

AIR INLET PRESSURES

100 PSI27 Kg/cm

70 PSI25 Kg/cm

40 PSI3 Kg/cm 2



Flow Rates1

57

AutoPump®

Top Inlet, Long AP2TAir Consumption

IN WELL DEPTH

.2

.3

.4

.5

.6

.7

.8

.9

20 40 60 80 100 120 140 160 180 200

1.1

1.0

1.2


1.3

1.4

1.5

1.6

(SCF/GAL)

MetersFT.

36.61.6 2.21 3.81 24.4 30.5 169.457.24 8.84



PER

2.2

1.5

3.0

3.7

5.2

4.5

6.0

7.5

6.7

8.2

9.0

10.5

9.7

11.2

12

APPROXIMATE

40 PSI23 Kg/cm

70 PSI5 Kg/cm 2

7 Kg/cm100 PSI

2


58

AutoPump®

Top Inlet, ShortAP2TDescription

Max. Flow

O.D.

Length

1.6 gpm (6 lpm)

1.75 in (4.45 cm)

35 in. (89 cm)

The AP2 Top Inlet Short AutoPump provides maximumcapabilities and flow in a top inlet pump for 2” (50 mm)diameter wells having shorter water columns and/or theneed to pump down to lower water levels, compared tofull-length pumps. It is designed for applications requiringan elevated inlet, such as pumping total fluids from wellscontaminated with LNAPLs. It is offered in optionalversions to handle even the most severe remediation andlandfill pumping applications, and delivers flow rates up to1.6 gpm (6 lpm). The AP2 Long Bottom Inlet AutoPump iscomplemented by the most comprehensive selection ofaccessories to provide a complete system to meet site-specific requirements. Call QED for prompt, no-obligationassistance on your pumping project needs.

The AutoPump HeritageThe AP2 Top Inlet Short AutoPump is part of the famousAutoPump family of original automatic air-powered pumps,developed in the mid 1980s specifically to handle uniquepumping needs at remediation and landfill sites. Over theyears they’ve proven their durability at thousands of sitesworldwide. AutoPumps are designed to handle difficultpumping challenges that other pumps can’t, such assolvents, suspended solids, corrosives, temperatureextremes, viscous fluids and frequent start/stop cycles.Beyond just the pump, AutoPump systems offer the mostcomplete range of tubing, hose, connectors, caps andaccessories to help your installation go smoothly. Thissuperior pumping heritage, application experience andsupport back up every AutoPump you put to work onyour project.






59

AutoPump®

Top Inlet, Short AP2TPump Dimensions Specifications & Operating Requirements


O.D. 1.75" (4.45 cm)

Liquid Discharge

Inlet

Air Supply

Exhaust

Len

gth

to

To

p o

f F

itti

ng

s 3

5" (

89 c

m)

Act

uat

ion

Lev

el 3

1" (

79 c

m)






Air Usage

Min. Liquid Density


Pump BodyPump Ends


Fitting Type





Air Exhaust



2" - Short AP2 Top InletTop1.75 in. (4.45 cm)35 in. (89 cm)5.7 lbs (2.6 kg)1.6 gpm (6.0 lpm)

.05 - .08 gal (.19 - .30 l)300 ft (91.4 m)5 - 130 psi (0.4 - 9.2 kg/cm2)31 in. (78.7 cm)0.39 - 2.59 scf/gal (2.9 - 19.3 liters/fluid liter)See air usage chart

0.7 SpG (0.7 g/cm3)







60

AutoPump®

Top Inlet, ShortAP2T

MINUTE

I.D. HOSE

13 mm

12.240200

6.1

060 FT.160100 120 140 18080 200

42.736.618.3 24.4 30.5 Meters168.84 9.45

0

1

I.D. HOSE

3.8

1/2-INCH2

WITH

MINUTE

7.6

DEPTH IN WELL

WITH

PER

APPROXIMATE

LITERS

MINUTE

13 mm

I.D. HOSE


LITERS

APPROXIMATE

1/2-INCH

GALLONS

PER 3 11.4

4 15.1

4012.2

02006.1

0140

42.7120

36.660

18.380

24.4100

30.5FT.Meters

18054.9

16048.8 61

200

1

I.D. HOSE

3.8

11.4PER 3

WITH2

MINUTE

7.6

GALLONS

4 15.1

Meters18.36.1 12.2 54.936.6 42.7 48.824.4 30.5 61


402000

14012060 80 1000

FT.180160 200

DEPTH IN WELL

WITH

PER

IN WELL DEPTH


APPROXIMATE

LITERS

MINUTE

13 mm

I.D. HOSE

7.62

I.D. HOSE

1

1/2-INCH

3.8

MINUTE

WITH

PER 3 11.4GALLONS

4 15.1

WITH

PER

AIR INLET PRESSURES

100 PSI7 Kg/cm 2

25 Kg/cm70 PSI3 Kg/cm

40 PSI2


5 Kg/cm 2

100 PSI7 Kg/cm 2

AIR INLET PRESSURES

40 PSI3 Kg/cm 2 5 Kg/cm

70 PSI2

7 Kg/cm 2100 PSI

AIR INLET PRESSURES



Flow Rates1

61

AutoPump®

Top Inlet, Short AP2T

DEPTH IN WELL

9.71.3

4.5.6

36.6120

.3

02 04 06 08 0016.1 12.2 30.518.3 24.4

.2

.4

.5

2.2

140 FT.061 081 0029.45 1642.7 48.8 Meters

1.5

3.0

3.7

.8

.7

.9

1.1

1.0

1.2

6.0

5.2

6.7

8.2

7.5

9.0

APPROXIMATE

(SCF/GAL)

1.4

1.5

1.6GALLON PUMPED

STANDARDCUBIC FEET OF AIRPER

1.8

1.7

1.9

LITER PUMPED(STD L/LITER)

10.5

11.2

12

LITER OF AIR13.5

12.7 PER

14.2 STANDARD

2.3

2.0

2.1

2.2

2.5

2.4

2.6

17.2

15

15.7

16.5

18.7

18.0

19.4

2.8

2.7

20.9

20.2

40 PSI3 Kg/cm 2

70 PSI5 Kg/cm 2

100 PSI7 Kg/cm 2

Air Consumption


62

AutoPump®

Tubing & Hose

QED offers the choice of jacketed nylon tubing or hose sets for downwelluse, and single tubes and hoses for surface runs to fit each project’s needs.The jacketed nylon tubing is an exclusive developed by QED that encloses allof the nylon tubes inside a strippable nylon outer cover, a convenient pack-age designed to provide lighter weight, increased chemical resistance,smoother handling and a smaller profile in the well. For applications wherethe tighter bend radius of hose is preferred, hose sets are offered in severalsizes. Other hose and tube materials are available for special applications.

The choice of hose and tube connection fittings used on pumps, caps andother components can make an important difference in the ease and qualityof installation and service on your project. That’s why QED offers a variety ofconnecting fitting types and materials, including quick-connects in both brassand stainless steel.

Note: All QED tube, hose and fitting combinations are engineered specificallyto provide user safety, high pullout strength, ease of installation, andleak tight connections for maximum assurance that the pumpingsystem goes in right and stays trouble-free. It is especially importantthat the mating diameters and the tolerances of fittings, tubes andhoses be carefully controlled to ensure a fit that is snug yet doesn’tdamage the hose or tube due to excessive stretching. Don’t trust yourproject to general purpose tubing, hose, and fittings that weren’tspecifically designed to work together.

AdvantagesAll dimensions of QED tube, hoseand fittings are carefully designedand controlled to ensure high flowcapacity, easy assembly, highpullout strength and leak-tightconnections

Innovative jacketed nylon tubing ishighly regarded by experiencedusers for its light weight, smoothprofile and ease of handling

QED offers an unmatched rangeof connector fitting options tomake installation and maintenanceeasier and more efficient

Model Type MaterialLiquid

DischargeSize

TypeAir

SuppySize

ExhaustSize

MaximumPressure

MaximumDepth

MinimumBend

Radius

HIFLOTUBE Jacketed 3-Tube set Nylon 12 1.25” OD 1/2” OD 5/8”OD 200 PSI 400 feet 8”(32 mm) (13 mm) (16 mm) (14 kg/cm2 (122 m) (20 cm)

STDTUBE Jacketed 3-Tube set Nylon 12 1” OD 1/2” OD 5/8”OD 200 PSI 400 feet 7”(25.4 mm) (13 mm) (16 mm) (14 kg/cm2) (122 m) (18 cm)

AP2TUBE 3-Tube set Nylon 12 5/8” OD 3/8”OD 1/2”OD 200 PSI 400 feet 2.5”(16 mm) (9.5 mm) (13 mm) (14 kg/cm2) (122 m) (6.5 cm)

HIPSIHOSE 3-hose set Nitrile 1” ID 3/8”ID 1/2”OD 300 PSI 600 feet 8”(25.4 mm) (9.5 mm) (13 mm) (21 kg/cm2) (183 m) (20 cm)

HIFLOHOSE 3-hose set Nitrile 1” ID 3/8”ID 1/2”OD 100 PSI 200 feet 8”(25.4 mm) (9.5 mm) (13 mm) (7 kg/cm2) (61 m) (20 cm)

STDHOSE 3-hose set Nitrile 3/4” ID 3/8”ID 1/2”OD 300 PSI 600 feet 7”(13 mm) (9.5 mm) (13 mm) (21 kg/cm2) (183 m) (18 cm)

AP2HOSE 3-hose set Nitrile 1/2” ID 1/4”ID 3/8”ID 300 PSI 600 feet 5”(13 mm) (6 mm) (9.5 mm) (21 kg/cm2) (183 m) (13 cm)

63

AutoPump®

AutoPump Well Caps

Hundreds of wellhead cap and flange combinations areavailable from QED on a standard and custom basis tofit site needs and ease installation and maintenance.The table below lists some of our most commonlychosen wellhead assemblies. Our assemblies are basedon the know-how gained through our 20 years experienceand thousands of installations. Besides connectingto the pump tubing or hose, wellheadassemblies have to be designed forsafety, equipment support strength,pump level adjustment, access for dataand sample collection, and durability.Call us for more detailed information.

Quick connect fittingavailable in brass orstainless steel

Compression fittingfor pass-through hoseor tubing. Available innylon

Custom flange

Vacuum seal well capwith brass quick connects,

filter regulator andpump cycle counter

WellheadAssembly

DescriptionFitting

Materials Well DiametersFitting Types(hose & tubing)

Non-sealing cap with open pass-through holes for hoses; allowseasy pump height adjustment withsupport rope/cable

Non-sealing cap with fittings forconnection to air supply and liquiddischarge lines

Sealing cap with fittings forconnection to air supply andliquid discharge lines

Sealing flange with fittings forconnection to air supply and liquiddischarge lines

Open-hole cap

Slip

Vacuum Seal

Flange

2”, 4”, 6”, custom(50, 100, 150 mm)

2”, 4”, 6”, custom(50, 100, 150 mm)

2”, 4”, 6”, custom(50, 100, 150 mm)

Custom

Brass, SS, poly

Brass, SS, poly

Brass, SS, poly

No fittings

quick-connects,compression fittings



Filter Regulatorsee page 89

Pump Cycle countersee page 88

Vacuum Cap Seal

64

AutoPump®

Flow Counters

Cycle CounterThe Cycle Counter detects and displays each AutoPump cycle via the pulse of air that occurs in the supply line.Since the liquid volume delivered by each pump cycle is relatively consistent for a given well condition, the totalliquid volume delivered can be monitored with these cycle counts. An important advantage of the Cycle Countermethod is its long-term reliability and low maintenance, since it requires no contact with the pumped fluid and noextra components in the liquid flow path. Cycle Counters can also be ordered with an electronic pulse output tosupport automated flow data collection.

Cycle Counter SpecificationsType: Magnetic piston/springReadout: Direct digital (remote option), non-resettableMaximum Pressure: 200 psi (14 kg/cm2)End options: NPT, barb, quick connect

65

AutoPump®

Air Supply

Filter regulatorsFilter regulators are recommended for each pump at the wellhead to economize on system airconsumption, allow control of pump flow rate, and reduce service needs caused by air system

debris and contaminants. These high quality filter regulators are coated on the inside toprevent corrosion from condensed moisture. All QED well caps and flanges include mountingprovisions for these filter regulators, and other mounting options are available.

Compressor SizingA compressed air supply is required to power AutoPumps. Estimation of the fluid flow ratesand air consumption of the AutoPumps and sizing the fluid lines, air lines, and air compres-

sor involves a number of factors. Our application specialists are ready to assist you.

The flow rates and air consumption for the AutoPumps can be compared by using the charts providedin this catalog for each model. The flow rate and air use curves in this catalog are based on pumpingto atmospheric pressure at the wellhead, and do not take into account any liquid piping systembackpressures due to elevation changes or fluid friction.

Finally, there are some initial guidelines for air compressors. Most importantly, follow all applicationguidelines of the compressor manufacturer. A piston compressor may be a start / stop type or a constant

run type. The tank (receiver) must be large enough, particularly for the start / stop type. The motor should not turn on moretimes an hour than recommended by the manufacturer. And start/stop compressors are typically assigned a 50% maximumduty cycle, meaning that the compressor is sized to provide twice the maximum air demand of the entire AutoPump system.

Rotary screw compressors are designed for constant operation, and so are sized to just slightly exceed the maximum airsupply requirement; it is recommended that rotary screw compressors not be grossly oversized because some types may bedamaged by continued operation at low partial capacity.

66

AutoPump®

Tank Full Shutoffs

QED’s Tank-Full Shutoff senses when your recovery tank is full and automatically shuts off the pump air supply.It is all pneumatic for safety, and includes two independent level detection methods for failsafe operation.The Tank-Full Shutoff threads into standard 2” NPT fittings on drums and tanks.

Tank Full Shutoff Specifications:Power Supply: Fully pneumaticLevel Sensor Type: Dual; Bubbler tube and float switchAir Usage: 0.7 scfm @ 80 psi (19.8 lpm @ 5.6 kg/cm2)Tank Connection: 2-inch male NPT

x xx xxx xx xxx

x xx xxx xx xxxx xx xx xxx xxx

xxxxxxxxxxx xxxxxxxxxxx

xxxxxxxxxxx xxxxxxxxxxx

0

1

0

TANK FULL

TANK FULLTANK FULL

SENSOR

RESETND CATOR

PRODUCTRECOVERY

OIL / WATER

TANKSURGE TANK

COMPRESSOR

SEPARATOR

Additional Single Sensor

Optional TFSOUnit Lengths Are

Available ForDifferent TankConfigurations

Air Supply To

Air Filters / Regulators

Pumps And / Or OtherControl Panels

TFSO Units Can Be Added

Standard TFSOUnit

Dual TFSO Sensor Hose

To The System

Wall MountingControl Panel12" x 14" x 11"

Dual-Sensor Tank-Full Shut-Off (TFSO) System

(30.5cm x 35.6 cm x 27.9 cm)(20 lbs.) (9.1 kg)

67

AutoPump®

Application Data Sheet

Address:

Name: Title:

Company:

Email:

Phone: FAX:

Address:

Company:

Site Name:

Project Ref:

Phone: FAX:

SITE INFORMATIONCUSTOMER INFORMATION

Site Information FormQED USE ONLY Quote Number

Today's Date

Sales Order NumberP.O. Box 3726 Ann Arbor, MI 48106-3726 USA 1-800-624-2026 FAX (734) 995-1170 [email protected] www.qedenv.com

SENSORS REQUIRED APPLICATION TYPE

Tank-Full Shut-Off

High-Water Shut-Off

Fluid Level

Pump Cycle Counter

Total Fluids

DNAPL

Dual Pump

LNAPL

Condensate

Leachate

APPLICATION DESCRIPTION

Please attach sketch of site, well and equipment layout.

Properties of pumped fluids contaminants/viscosity/concentrations/pH/temperature/specific gravity/TDS ( . )attach additional information

Pumping Objectives ( ).attach additional information and diagrams

Note: Please note any special characteristic on illustration above

DAB

F

G

JDNAPL

LNAPL

Water

C

H

M

I

N

E

K

L

Well casing ID at wellheadWell casing ID at location of equipment

Well casing OD

Well casing to top of outer / vault casing

Vault DimensionsVault Depth

Desired fluid pumping rate

Casing MaterialsWell angle off vertical (% or degrees)Exhausting inside or outside the wellWell under vacuum (Hg or H2O)Any known material degradation (yes/no)

Depth to top of screen

Depth to top of LNAPL layer (if present)LNAPL thickness (if present)

Depth to static water level

Final drawdown level

Depth to bottom of the screen

Depth to bottom of the well

LNAPL removal rate (if present)

Water / Leachate removal rate

Sump length

DNAPL removal rate (if present)

DNAPL thickness (if present)

Maximum daily water table fluctuation

ABCDEFGHI

JKLMN

WELL IDENTIFICATION NUMBER

WELL DATA

The information provided on this form will be kept confidential by QED.

Environmental SystemsA division of Severn T ent Laboratories, Inc.

AutoPump®

Notes

AutoPump®

Warranty

AutoPump®

QED AutoPump Warranty Period Summary

Following is a summary of the warranty periods only for QED AutoPumps and accessories;this IS NOT the complete warranty. Contact QED for a copy of the complete warranty

1. AP4+ AutoPumps (Long and Short lengths; Top- and Bottom-Inlets)warranted for five (5) years: 100% materials and workmanship; AP4+ Low-DrawdownAutoPumps®

warranted for one (1) year: 100% materials and workmanship.

2. AP3 AutoPumps (Long and Short lengths; Top- and Bottom-Inlets)warranted for two (2) years: 100% materials and workmanship.

3. AP2 AutoPumps (Long and Short lengths; Top- and Bottom-Inlets)warranted for one (1) year: 100% materials and workmanship.

4. Hoses, Tubing, Fittings, Well Caps and Flangeswarranted for one (1) year: 100% materials and workmanship.There will be no warranty for application or material compatibility.

5. Pneumatic Data Modules / Logic Control Panelswarranted for one (1) year: 100% materials and workmanship.

6. Parts and Repairswarranted for ninety (90) days: 100% materials and workmanship; when repairs areperformed by QED or its appointed agent; from date of repair or for the full term ofthe original warranty, whichever is longer. Separately sold parts are warranted forninety (90) days: 100% materials and workmanship.

Beyond the Pumps…Success with a pumping system involves more than just the pumps.Over 20 years of specialized air-powered pumping experience onthousands of sites with a broad range of applications andgroundwater issues has allowed us to develop unequalled expertiseand problem solving capabilities.

QED technical experts will work with you on identifing the relevantsite information to assure meeting your remediation and landfillpumping objectives. The equipment will be selected to meet yoursite-specific application.

AccessoriesDownwell hose and tubing

An array of connectors and fittings for ease of installation and service

Mix of wellhead assemblies to meet site-specific needs

Fluid discharge and air supply piping layouts and components

Tank-full shut-off and other safety items and features

Pump cycle counters

Custom requirements

©2014 Thermo Fisher Scientific Inc. All rights reserved.

Australia: For customer service, call 1300-735-295 Visit us online at: www.thermofisher.com.auNew Zealand: For customer service, call 0800-422-469 Visit us online at: www.thermofisher.co.nz

mandy.jansz

ANZ Supplier

Documents

AutoPump Catalog...Long AP2-Bottom Inlet Short AP2-Bottom Inlet 2” Top Inlet AP Pumps Long AP2-Top Inlet Short AP2-Top Inlet Long AP3B 54 Short AP3B 58 Bottom Bottom 2.63 / 6.68