8/6/2019 AVR 340 OM(web)rev3-21-06

1/68

DIGITAL LOGIC 7 VID 1 DVD

CD

FMAM

TAPE

6 8 C H

VID2

VID3

VID4

PROLOGIC

3STEREO

HEADPHONE

DSP

57 CH.STEREO

SURR.OFF

AVR340

Optical 4 Coax ial 4Video4

AVR 340AUDIO/VIDEO RECEIVER

OWNERS MANUAL

Power for the Digital Revolution.

8/6/2019 AVR 340 OM(web)rev3-21-06

2/68

AVR 340 AUDIO/VIDEO RECEIVER

3 Introduction4 Important Safety Information4 Unpacking5 Front-Panel Controls8 Rear-Panel Connections

11 Main Remote Control Functions15 Zone II Remote Control Functions16 Installation and Connections19 System Configuration19 Speaker Selection and Placement 21 System Setup21 Using the On-Screen Display22 Input Setup23 Audio Setup23 Surround Setup26 Automated Speaker Setup Using EzSet/EQ28 Manual Setup28 Speaker Size30 Speaker Crossover Settings30 Delay Settings

31 Output Level Adjustment 34 Operation34 Basic Operation34 Source Selection34 6-Channel/8-Channel Direct Input 34 Volume and Tone Control35 Surround Mode Selection36 Surround Mode Chart 38 Digital Audio Playback 40 Surround Mode Availability for Incoming Bitstreams41 Tuner Operation42 Recording42 Using42 Output Level Trim Adjustment

42 Dim Function44 Advanced Features46 Multiroom Operation48 Programming the Main Remote48 Programming Device Codes48 Macro Programming49 Programmed Device Functions50 Volume Punch-Through50 Channel Control Punch-Through50 Transport Control Punch-Through50 Resetting the Remote Memory51 Function List 53 Setup Code Tables63 Troubleshooting Guide63 Processor Reset 64 Technical Specifications64 Trademark Acknowledgements65 Index66 Appendix Settings Worksheet

TheBridgeTM

2 TABLE OF CONTENTS

Typographical ConventionsIn order to help you use this manual with the remote control, front-panel controls and rear-panel ccertain conventions have been used.

EXAMPLE (bold type) indicates a specific remote control or front-panel button, or rear-panelconnection jack

EXAMPLE (OCR type) indicates a message that is visible on-screen or on the front-panel

information display1 (number in a square) indicates a specific front-panel control

(number in a circle) indicates a rear-panel connection

a (number in an oval) indicates a button or indicator on the remote

(letter in an oval) indicates a button on the Zone II remote

The appearance of the text or cursor for your receivers on-screen menus may vary slightly from illustrations in this manual. Whether the text appears in all uppercase or upper- and lowercase chaperformance and operation remain the same.

For Canadian model

Modle pour les CanadienCet appareil numrique de la classe B est confo la norme NMB-003 du Canada.Sur les modles dont la f iche est polarisee: ATTENTION: Pour viter les chocs lectriquesla lame la plus large de la fiche dans la bornecorrespondante de la prise et pousser jusquau f

This class B digital apparatus complies with CaICES-003.For models having a power cord with a polarizeCAUTION: To prevent electric shock, match w

of plug to wide slot, fully insert.

Please register your product on our Web site at www.harmankardon.com. Note: Youll need theproducts serial number. At the same time, you canchoose to be notified about our new products and/orspecial promotions.

8/6/2019 AVR 340 OM(web)rev3-21-06

3/68

INTRODUCTION

Thank you for choosing Harman Kardon ! Withthe purchase of a Harman Kardon AVR 340, you areabout to begin many years of listening enjoyment.Designed to provide all the excitement and detail of movie soundtracks andevery nuance of musical selec-tions, the AVR 340accomplishes its mission by har-nessing advanced technologies usually found only inhigher-priced receivers.

The AVR 340 has been engineered so that it is easyto take advantage of all the power of its digital tech-nology. However, to obtain the maximum enjoyment from your new receiver, we urge you to read thismanual. A few minutes spent learning the functions of the various controls will enable you to take advantageof all the power the AVR 340 is able to deliver.

If you have any questions about this product, its instal-lation or its operation, please contact your retailer orcustom installer. They are your best local sources of information.

Description and FeaturesThe AVR 340 is versatile and multifeatured, incorpo-rating a wide range of listening options. In addition toDolby Digital and DTS decoding for digital sources,a broad choice of Matrix surround-encoded or stereosurround modes are available for use with your CD,VCR, TV broadcasts and the AVR 340s own FM/AMtuner. Along with Dolby Digital EX, Dolby Pro Logic IIx,DTS Neo:6, DTS 96/24 , Dolby 3 Stereo, and Halland Theater modes, the AVR 340 offers HarmanInternationals exclusive Logic 7 processing in both5.1 and 7.1 versions to create a wider, more envelopingfield environment and more defined fly-overs and pans.

Another exclusive is VMAx, which uses proprietaryprocessing to create an open, spacious sound fieldeven when only two front speakers are available. DolbyVirtual Speaker is also available to create an envelop-ing sound field when fewer than six speakers areused. The latest Dolby Headphone modes provide amuch more open and realistic presentation for privateheadphones listening.

In addition to providing a wide range of listeningoptions, the AVR 340 is easy to configure so that it provides the best results with your speakers and spe-cific listening-room environment. On-screen menuscombine with the EzSet/EQ system to automate

speaker configuration and overall setup, resulting in aperfectly balanced sound field presentation that accu-rately reproduces the artists intent.

In addition to the configuration settings, EzSet/EQ alsoincludes room equalization so that the signals sent toeach speaker are tailored to provide accurate sonicquality with your specific combination of speaker type,room size and other factors that influence room

acoustics. With EzSet/EQ, your system is custom-con-figured in a few minutes with accuracy that previouslyrequired expensive and hard-to-use test equipment.

In tandem with EzSet/EQ, the AVR 340 includes a fullset of manual configuration settings for those who

wish to custom-trim their system even further. AQuadruple Crossover bass management systemmakes it possible to enter different crossover settingsfor each speaker group.

For the ultimate in flexibility, the AVR 340 featuresconnections for five video devices, all with bothcomposite and S-video inputs. Two additional audioinputs are available, and eight digital inputs make the

AVR 340 capable of handling all the latest digital audiosources. For compatibility with the latest HDTV videosources and progressive scan DVD players, the

AVR 340 also features assignable two-input, wide-bandwidth, low-crosstalk component video switching.

The front panel offers coax and optical digital inputsfor direct connection to digital recorders. Two videorecording outputs, a preamp-out and a color-codedeight-channel input make the AVR 340 virtually future-proof, with everything needed to accommodate tomor-rows new formats right onboard.

Until now, Harman Kardon AVRs have been able toaccommodate almost any source device equippedwith line-level analog, optical digital or coaxial digitaloutputs, including most digital media players. With onesimple connection between the AVR 340 and theoptional Harman Kardon , you are able tolisten to materials stored on your compatible iPod*(not included). Your AVRs system remote control hasbeen preprogrammed with control codes that enableyou to select tracks for playback and navigate manyof your iPods functions, even from across the room.The Bridge will even let you charge your iPod.

The AVR 340s multizone options and a standardZone II remote control make it possible to listen toa separate source in a room while the main hometheater uses a different source. With assignable rearsurround channel amplifiers, you may create a basicremote listening zone without any additional equip-ment. For one-wire multiroom connectivity, the

AVR 340 is A-BUS/ READY , requiring only a singleCategory 5/5e cable and an optional remote module

to power remote speakers while controlling volumeand enabling full control over the program source andcompatible IR-controlled devices. The units Multiroomoutputs may also be used to feed an optional, externalpower amplifier and volume control.

The AVR 340s powerful seven-channel amplifier usestraditional Harman Kardon high-current design tech-

nologies to meet the wide dynamic range of any program selection.

Harman Kardon invented the high-fidelity receivermore than fifty years ago. Withstate-of-the-art circuiand time-honored circuit designs, the AVR 340

perfect combination of the latest in digital audio tech-nology, aquiet yet powerful analog amplifier in aele-gant, easy-to-use package.

s A wide range of digital and matrix surroundmodes, including Dolby Digital, Dolby Digital EX,Dolby Pro Logic IIx, Dolby Virtual Speaker, DolbyHeadphone, DTS, DTS-ES Discrete and Matrix,DTS 96/24 and DTS Neo:6

s Seven channels of high-current amplifications Harman Kardons exclusive Logic 7 processing,

available with both 7.1 and 5.1 processing ina variety of modes, and two modes of VMAx

s system with included micro-phone automatically configures speakers,sets delay times and output levels, and per-forms room equalization for optimal soundpresentation

s Programmable remote for control of AVR andseven additional source components

s High-bandwidth, HDTV-compatible componentvideo switching with assignable inputs andcross-conversion from composite and S-video

s Discrete front-panel coaxial and optical digitalinputs for easy connection to portable digital

devices and video game consoless Connects to Harman Kardons

(optional) for charging, playback and controlof a compatible iPod device (not included)

s Input titling for all input sources (except tuner)s Extensive bass management options, includ-

ing four separate crossover groupingss On-screen menu and display system with

choice of blue or black background screen,available with component video

s A/V Sync delay adjustable for each inputdelivers perfect lip sync with digital programsor video displays

s Extensive multiroom options, including a stan-dard Zone II remote, assignable surroundback amplifier channels and A-BUS/ READY

capability for listening to a separate source ina remote zone

TheBridgeTM

/EQ

TheBridgeTM

INTRODUCTION 3

*Compatible with all iPod models equipped with a dock connector, including third-generation Click Wheel models and newer. Not compatible with iPod shuffle models. AlthoughiPod video and photo models are compatible, video files and images stored on the iPod may not be viewed.

8/6/2019 AVR 340 OM(web)rev3-21-06

4/68

SAFETY INFORMATION

Important Safety Information

Verify Line Voltage Before UseYour AVR 340 has been designed for use with120-volt AC current. Connection to a line voltageother than that for which it is intended can create asafety and fire hazard and may damage the unit.

If you have any questions about the voltage requirementsfor your specific model, or about the line voltage in yourarea, contact your selling dealer before plugging the unit into a wall outlet.

Do Not Use Extension CordsTo avoid safety hazards, use only the power cordattached to your unit. We do not recommend that extension cords be used with this product. As with allelectrical devices, do not run power cords under rugsor carpets or place heavy objects on them. Damagedpower cords should be replaced immediately by an

authorized service center with a cord meeting factoryspecifications.

Handle the AC Power Cord GentlyWhen disconnecting the power cord from an AC out-let, always pull the plug; never pull the cord. If you donot intend to use the unit for any considerable lengthof time, disconnect the plug from the AC outlet.

Do Not Open the CabinetThere are no user-serviceable components inside thisproduct. Opening the cabinet may present a shock hazard, and any modification to the product will voidyour guarantee. If water or any metal object such as apaper clip, wire or a staple accidentally falls inside theunit, disconnect it from the AC power source immedi-ately, and consult an authorized service center.

CATV or Antenna GroundingIf an outside antenna or cable system is connected tothis product, be certain that it is grounded so as to pro-vide some protection against voltage surges and staticcharges. Section 810 of the National Electrical Code,

ANSI/NFPA No. 70-1984, provides information withrespect to proper grounding of the mast and supportingstructure, grounding of the lead-in wire to an antennadischarge unit, size of grounding conductors, locationof antenna discharge unit, connection to groundingelectrodes and requirements of the groundingelectrode.

NOTE TO CATV SYSTEM INSTALLER:This reminderis provided to call the CATV (Cable TV) systeminstallers attention to article 820-40 of the NEC that provides guidelines for proper grounding and, in par-ticular, specifies that the cable ground shall be con-nected to the grounding system of the building, asclose to the point of cable entry as possible.

Installation Locations To ensure proper operation and to avoid the poten-

tial for safety hazards, place the unit on a firm andlevel surface. When placing the unit on a shelf, becertain that the shelf and any mounting hardwarecan support the weight of the product.

s Make certain that proper space is provided bothabove and below the unit for ventilation. If thisproduct will be installed in a cabinet or otherenclosed area, make certain that there is sufficient air movement within the cabinet. Under somecircumstances a fan may be required.

s Do not place the unit directly on a carpetedsurface.

s Avoid installation in extremely hot or cold locations,or in an area that is exposed to direct sunlight orheating equipment.

s Avoid moist or humid locations.

s Do not obstruct the ventilation slots on the top of the unit, or place objects directly over them.

s Due to the weight of the AVR 340 and the heat generated by the amplifiers, there is the remotepossibility that the rubber padding on the bottomof the units feet may leave marks on certainwood or veneer materials. Use caution whenplacing the unit on soft woods or other materialsthat may be damaged by heat or heavy objects.Some surface finishes may be particularly sensitiveto absorbing such marks due to a variety of factorsbeyond Harman Kardons control, including thenature of the finish, cleaning materials used, and

normal heat and vibration caused by the use of theproduct, or other factors. We recommend that cau-tion be exercised in choosing an installation loca-tion for the component and in normal maintenancepractices, as your warranty will not cover this typeof damage to furniture.

CleaningWhen the unit gets dirty, wipe it with a clean, soft, drycloth. If necessary, and only after unplugging the ACpower cord, wipe it with a soft cloth dampened withmild soapy water, then a fresh cloth with clean water.Wipe dry immediately with a dry cloth. NEVER usebenzene, aerosol cleaners, thinner, alcohol or any other

volatile cleaning agent. Do not use abrasive cleaners,as they may damage the finish of metal parts. Avoidspraying insecticide near the unit.

Moving the UnitBefore moving the unit, be certain to disconnect anyinterconnection cords with other components, andmake certain that you disconnect the unit from the

AC outlet.

Important Information for the UserThis equipment has been tested and found to comply

with the limits for a Class-B digital device, pursuPart 15 of the FCC Rules. The limits are designedprovide reasonable protection against harmful intence in a residential installation. This equipment ates, uses and can radiate radio-frequency enerand,if not installed and used in accordance with theinstructions, may cause harmful interference to racommunication. However, there is no guarantee tharmful interference will not occur in a particularlation. If this equipment does cause harmful interence to radio or television reception, which can bdetermined by turning the equipment off and on,user is encouraged to try to correct the interferenone or more of the following measures:

s Reorient or relocate the receiving antenna.

s Increase the separation between the equipmentand receiver.

s Connect the equipment into an outlet on a circdifferent from that to which the receiver is

s Consult the dealer or an experienced radio/TVtechnician for help.

This device complies with Part 15 of the FCC RuOperation is subject to the following two conditio(1) this device may not cause harmful interferencand (2) this device must accept interference receiincluding interference that may cause undesiredoperation.

NOTE:Changes or modifications may cause thisunit to fail to comply with Part 15 of the FCC Ruand may void the users authority to operate theequipment.

UnpackingThe carton and shipping materials used to protectnew receiver during shipment were specially desito cushion it from shock and vibration. We suggethat you save the carton and packing materials fouse in shipping if you move, or should the unit evneed repair.

To minimize the size of the carton in storage, youwish to flatten it. This is done by carefully slittintape seams on the bottom and collapsing the cartoOther cardboard inserts may be stored in the sam

manner. Packing materials that cannot be collapsshould be saved along with the carton in a plastic

If you do not wish to save the packaging materialplease note that the carton and other sections of tshipping protection are recyclable. Please respectenvironment and discard those materials at a locarecycling center.

It is important that you remove the protective plafilm from the front-panel lens. Leaving the film iwill affect the performance of your remote contro

4 SAFETY INFORMATION4 SAFETY INFORMATION

8/6/2019 AVR 340 OM(web)rev3-21-06

5/68

FRONT-PANEL CONTROLS

1 Main Power Switch:Press this button to applypower to the AVR 340. When the switch is pressedin, the unit is in a Standby mode, as indicated by theamberPower Indicator2 . This button MUST bepressed in to operate the unit. To turn the unit off and to prevent the use of the remote control, thisswitch should be pressed until it pops out from thefront panel and the word OFF is seen at the top of the switch.

NOTE:This switch is normally left in the ON position.

2 Power Indicator:This LED lights amber when theunit is in the Standby mode to signal that the AVR isready to be turned on. When the unit is in operation,the indicator is blue.

3 Standby/On Switch:When theMain PowerSwitch 1 is ON, press this button to turn on the

AVR 340; press it again to turn the unit off. ThePowerIndicator2 turns blue when the unit is on.

4 Headphone Jack: This jack may be used to listento the AVR 340s output through a pair of headphones.The speakers will automatically be turned off when theheadphone jack is in use. When configuring your sys-tem using EzSet/EQ, the calibration microphone shouldbe plugged into this jack using the supplied adaptorthat converts the small mini-plug at the end of themicrophones cord to a 1/4" plug.

5 Tone Mode:This button controls the tone modesettings, enabling adjustment of the bass and trebleboost/cut. You may also use it to take the tone con-trols out of the signal path completely for flatresponse. The first press of the button displays aTONE IN message in theLower Display Line and in the on-screen display. To take the controlsout of the signal path, press either of the / Buttons ) until the display readsTONE OUT .

To change the bass or treble settings, make sure that TONE IN appears in theLower Display Lineor press either of the / Buttons ) until it does.

Press theTone Mode Button5 until the desiredoption of TREBLE MODE or BASS MODEappears in theLower Display Line and in theon-screen display and then press either of the /Buttons ) to enter the desired boost or cut setting.Both treble and bass contours may be boosted orcut by up to + or 10dB in increments of 2dB.See pages 23 and 34 for more information on thetone controls.

NOTE:The AVR 340 is not equipped with a tradition

Balance control. When listening to two-channel matals, if you wish to adjust the stereo image, you mayuse the Channel Adjust Selector to increase ordecrease the level of the left front channel by up to or 10dB, and then to decrease or increase the rightfront channel by the corresponding amount. Howevwhen listening to surround materials and most two-channel materials, it is recommended that you leavethese settings at the results obtained during the confuration process described on pages 19 through 33.

1 Main Power Switch2 Power Indicator3 Standby/On Switch4 Headphone Jack 5 Tone Mode6 Speaker Selector7 Surround Mode Group Selector8 Surround Mode Selector9 Tuning Selector) / Buttons

! Tuner Band Selector@ Set Button# Digital Input Selector$ Preset Station Selector% Delay Adjust Selector^ Input Source Selector& Tuner Mode Selector* Optical 4 Digital Audio Input ( Coaxial 4 Digital Audio Input Video 4 Video Input Jacks

Video 4 Audio Input JacksChannel Adjust Selector

Volume Control Input Indicators Speaker/Channel Input Indicators Upper Display Line Lower Display Line Surround Mode Indicators Remote Sensor Window

DIGITAL LOGIC 7 VID 1 DVD

CD

FMAMTAPE

6 8 CH

VID 2

VID 3VID 4

PRO LOGIC

3 STEREOHEADPHONE

DSP5 7 CH. STEREO

SURR. OFF

12 6

7 #

(*

8 )!

@ )&%3

4

5 9$ ^

AVR340

Optical 4 Coaxial 4Video 4

FRONT-PANEL CONTROLS

FRONT-PANEL CONTROLS 5 5

NOTE:To make it easier to follow the instructions that refer to this illustration, a larger copy may be downloaded from the Product Support section for this productat www.harmankardon.com.

8/6/2019 AVR 340 OM(web)rev3-21-06

6/68

6 Speaker Selector: Press this button to beginthe process of configuring the unit to match the typeof speakers used in your listening room. (See pages2830 for more information on speaker setup andconfiguration.)

7 Surround Mode Group Selector:Press this but-ton to select the top-level group of surround modes.Each press of the button will select the current or last used mode in each of the surround mode groups(e.g., Dolby, DTS, DTS Neo:6, Logic 7, DSP, Stereo).When the button is pressed so that the name of thesurround mode group appears in the on-screen dis-play and in theLower Display Line , press theSurround Mode Selector8 to cycle through theindividual modes available. For example, press thisbutton to select Dolby modes, and then press theSurround Mode Selector8 to choose from thevarious Dolby mode options.

8 Surround Mode Selector:Press this buttonto select from among the available surround modeoptions for the mode group selected. The specificmodes will vary based on the number of speakersavailable, the mode group and if the input source isdigital or analog. For example, press theSurroundMode Group Selector7 to select a main modegrouping such as Dolby or Logic 7, and then pressthis button to see the specific mode choices available.Note that the digital surround modes, such as DolbyDigital and DTS, may not be accessed unless that typeof source signal is present, such as when a DVD movieor television signal programmed in Dolby Digital or DTSsurround sound is playing. For more information on sur-round mode selection, see pages 25 and 3541.

9 Tuning Selector:Press the left side of the buttonto tune lower-frequency stations and the right side of the button to tune higher-frequency stations. When thetuner is in the Manual mode, each tap will increase ordecrease the frequency by one increment. When thetuner receives a strong enough signal for adequatereception,MANUAL TUNED will appear in theon-screen display and theLower Display Line .When the tuner is the Auto mode, press the buttononce, and the tuner will scan for a station with accept-able signal strength. When the next station with astrong signal is tuned the scan will stop and the

on-screen display andLower Display Linewill indicateAUTO TUNED . When an FMStereo station is tuned, the display will readA UTO ST TUNED .

To switch back and forth between the Auto andManual tuning modes, press theTuner ModeSelector & .

) / Buttons:When configuring the AVR 340ssettings, use these buttons to select from all of theavailable choices.

! Tuner Band Selector:Press this button to turnthe AVR on and to select the Tuner as the input. Pressit again to switch between the AM and FM frequencybands. (See page 41 for more information on the tuner.)

@ Set Button:When making choices during thesetup and configuration process, press this buttonto enter the desired setting into the AVR 340s memory.

# Digital Input Selector:Press this button toselect one of the digital audio inputs or the analogaudio input for any source. (See pages 3841 formore information on digital audio.)

$ Preset Stations Selector: Press this button toscroll up or down through the list of stations that have

been entered into the preset memory. (See page 41for more information on tuner presets.)

% Delay Adjust Selector:Press this button tobegin the steps required to enter delay settings. (Seepages 3031 for more information on delay times.)

^ Input Source Selector:Press this button tochange the input by scrolling up or down through thelist of Input Indicators .

& Tuner Mode Selector:Press this button to select Auto or Manual tuning.When the button is pressed sothat theAUTO appears in theLower Display Line , the tuner will search for the next station with anacceptable signal when theTuning Selector9u is pressed.When the button is pressed so that MANUAL appears in theLower Display Line ,each press of theTuning Selector9u willincrease the frequency. This button may also be used toswitch between Stereo and Mono modes for FM radioreception. When weak reception is encountered, pressthe button so that MANUAL appears in theLowerDisplay Line and on the on-screen display toswitch to Mono reception. Press it again to switch back to Stereo mode. (See page 41 for more information onusing the tuner.)

* Optical 4 Digital Audio Input:Connect the opticaldigital audio output of an audio or video product to this

jack. When the input is not in use, the built-in shutter willclose to avoid dust contamination that might degradefuture performance.

( Coaxial 4 Digital Audio Input:This jack is usedfor connection to the output of portable audio devices,video game consoles or other products that have acoax digital audio jack.

Video 4 Video Input Jacks:These jacks maybe used for temporary connection to the composiS-video output of video games, camcorders or othportable video products. You may make a connecto either jack at any time, but not to both simultane

Video 4 Audio Input Jacks:These audio jacksmay be used for temporary connection to videogames or portable audio/video products such ascamcorders and portable audio players.

NOTE:The AVR 340 is shipped with two covers tmay be installed over the front-panel input jacks they are not in use.

Channel Adjust Selector:Press this button tobegin the process of trimming the channel outputels using an external audio source. (For more infotion on output level trim adjustment, see page 31

Volume Control:Turn this knob clockwise toincrease the volume, counterclockwise to decreasthe volume. If the AVR 340 is muted, adjusting th

Volume Control b will automaticallyrelease the unit from the silenced condition.

Input Indicators:The current selected sourcewill appear as one of these indicators. When the uis turned on, the entire list of available modes wilight briefly, and then revert to normal operation only the active mode indicator illuminated.

NOTE: When /DMP has been selected asthe input source, noInput IndicatorN will light.DMP/THE BRIDGE IS CONNECTED

will scroll across theUpper Display LineP , unlessyou have retitled the source name, in which case name will appear. See page 22 for more informaton input titling.

Speaker/Channel Input Indicators:These indi-cators are multipurpose, indicating both the speaketype selected for each channel and the incoming dasignal configuration.The left, center, right, side surand back surround speaker indicators are composethree boxes, while the subwoofer is a single box.Tcenter box lights when a small speaker is selecteand the two outer boxes light when large speakeselected. When none of the boxes are lit for the ce

surround or subwoofer channels, no speaker has beassigned that position. (See pages 2829 for moreinformation on configuring speakers.)

NOTE: When you have reassigned the surround bspeakers to the remote zone using theMULTIROOM SETUP menu, the boxes that indicate presence of the surround back speakers will automcally disappear, reflecting the fact that the main ling area is now configured for 5.1-channel operat

TheBridgeTM

FRONT-PANEL CONTROLS

6 FRONT-PANEL CONTROLS

FRONT-PANEL CONTROLS

8/6/2019 AVR 340 OM(web)rev3-21-06

7/68

(See page 46 for more information on reassigning thesurround back speakers for multiroom use.)

The letters inside each box display the active input channels. For standard analog sources, only the L and Rwill light, indicating a stereo input. For a digital source,the indicators will light to display the channels beingreceived at the digital input. When the letters flash, thedigital input has been interrupted. (See page 39 formore information on the Channel Indicators.)

Upper Display Line:Depending on the units sta-tus, a variety of messages will appear here. In normaloperation, this line will show current input source andwhich analog or digital input is in use. When the tuner isthe input, this line will identify the station as AM or FMand show the frequency and preset number, if any.

Lower Display Line:Depending on the units sta-tus, a variety of messages will appear here. In normal

operation, the current surround mode will show here.

Surround Mode Indicators:The current selectedsurround mode will appear as one of these indicators.Note that when the unit is turned on, the entire list of available modes will light briefly, and then revert tonormal operation with only the active mode indicatorilluminated.

NOTE: When the Dolby Virtual Speaker mode is inuse, no Surround Mode IndicatorR will light.However, the surround mode name will scroll in theLower Display LineQ .

Remote Sensor Window:The sensor behindthis window receives infrared signals from the remotecontrol. Aim the remote at this area and do not block or cover it.

FRONT-PANEL CONTROLS 7 7

FRONT-PANEL CONTROLS

8/6/2019 AVR 340 OM(web)rev3-21-06

8/68

f

g

he

d

c

b

a

Z

Y

X

W U

T

S Q O

N

M

L

0

12345

6 7 8 9 A B C D E F G H I

J

K

The Bridge

PRV

FM Antenna Jack Multiroom Audio Outputs CD Audio Inputs A-BUS Connector Multiroom IR Input Remote IR Carrier Output

Preamp Outputs Subwoofer Output Remote IR Input Remote IR Output Front Speaker Outputs Surround Back/Multiroom Speaker Outputs Surround Speaker Outputs Center Speaker Outputs Optical Digital Audio Inputs

Component Video Monitor Outputs Component Video 1 Inputs Component Video 2 Inputs Fan Ventsa AC Power Cordb Switched AC Accessory Outlet

c Unswitched AC Accessory Outlet d Optical Digital Audio Output e Coaxial Digital Audio Output f Coaxial Digital Audio Inputsg S-Video Monitor Output h DVD S-Video Input i Video 1 S-Video Input j DMP Connectork Video 1 S-Video Output

U Video 2 S-Video Input V Video 2 S-Video Output W Video 3 S-Video Input X 6/8-Channel Direct InputsY Video Monitor Output Z DVD Audio/Video Inputs

a Video 1 Audio/Video Inputsb Video 1 Audio/Video Outputsc Video 2 Audio/Video Inputsd Video 2 Audio/Video Outputse Video 3 Audio/Video Inputsf Tape Inputsg Tape Outputsh AM Antenna Terminals TheBridgeTM

NOTE:To assist in making the correct connectionsfor multichannel input, output and speaker connec-tions, all connection jacks and terminals are color-coded in conformance with the CEA standardsas follows:

Front Left: WhiteFront Right: Red

Center: GreenSurround Left: BlueSurround Right: GraySurround Back Left: BrownSurround Back Right: TanSubwoofer: PurpleCoaxial Digital Audio: Orange

Composite Video: YellowComponent Video Y: GreenComponent Video Pr: RedComponent Video Pb: Blue

FM Antenna Jack:Connect the supplied indoor(or an optional external) FM antenna to this terminal.

Multiroom Audio Outputs:Connect these jacksto the optional external audio power amplifier that isused for multizone distribution.

CD Audio Inputs:Connect these jacks to theanalog audio outputs of a compact disc player orCD changer.

A-BUS Connector:Connect this jack to anoptional A-BUS remote room product to extend the

multiroom capabilities of your AVR 340. See pagfor more information on A-BUS.

Multiroom IR Input:Connect the output of anIR sensor in a remote room to this jack to control

AVR 340s multiroom system and source devices

NOTE:To make it easier to follow the instructions that refer to this illustration, a larger copy may be downloaded from the Product Support section for this prodat www.harmankardon.com.

8 REAR-PANEL CONNECTIONS

REAR-PANEL CONNECTIONS

8/6/2019 AVR 340 OM(web)rev3-21-06

9/68

REAR-PANEL CONNECTIONS 9

REAR-PANEL CONNECTIONS

the remote room. See page 46 for more informationon multiroom operation.

Remote IR Carrier Output:The output of this jack is the full signal received at theRemote SensorWindowS , or input through theRemote IR Input

, including the carrier frequency that is strippedfrom these signals at theRemote IR Output . Usethis output to extend IR remote signals to the inputs of compatible products that require the full IR signal bydirect connection to the products remote IR input,or through the use of optional, external IR blasters.If you are in doubt as to which of the two IR Output

jacks to use, we recommend that you consult withyour dealer or installer, or check with the manufacturerof the external equipment you wish to control.

Preamp Outputs:Connect these jacks to anoptional, external power amplifier for applicationswhere higher power is desired.

Subwoofer Output:Connect this jack to the line-level input of a powered subwoofer. If an external sub-woofer amplifier is used, connect this jack to the sub-woofer amplifier input.

Remote IR Input:If the AVR 340s front-panelIR sensor is blocked due to cabinet doors or otherobstructions, an external IR sensor may be used.Connect the output of the sensor to this jack.

Remote IR Output:This connection permits theIR sensor in the receiver to serve other remote con-trolled devices. Connect this jack to the IR IN jack onHarman Kardon (or other compatible) equipment.

Front Speaker Outputs:Connect these outputsto the matching + or terminals on your left and right speakers. When making speaker connections alwaysmake certain to maintain correct polarity by connectingthe color-coded (white for front left and red for front right) (+) terminals on the AVR 340 to the red (+)terminals on the speakers and the black () terminalson the AVR 340 to the black () terminals on thespeakers. See page 16 for more information onspeaker polarity.

Surround Back/Multiroom Speaker Outputs:These speaker terminals are normally used to powerthe surround back speakers in a 7.1-channel system.

However, they may also be used to power the speak-ers in a second zone, which will receive the output selected for a multiroom system. To change the output fed to these terminals from the default of the SurroundBack speakers to the Multiroom Output, you must change a setting in theMULTI ROOMSETUP menu of the OSD system. See page 46for more information on configuring this speaker out-put. In normal surround system use, the brown andblack terminals are the surround back left channelpositive (+) and negative () connections and the tan

and black terminals are the surround back right posi-tive (+) and negative () terminals. For multiroom use,connect the brown and black SBL terminals to thered and black connections on the left remote zonespeaker and connect the tan and black SBR terminalsto the red and black terminals on the right remotezone speaker.

Surround Speaker Outputs:Connect these out-puts to the matching + and terminals on your sur-round channel speakers. In conformance with the CEAcolor-code specification, the blue terminal is the posi-tive, or +, terminal that should be connected to thered (+) terminal on the Surround Left speaker, whilethe gray terminal should be connected to the red (+)terminal on the Surround Right speaker. Connect theblack () terminal on the AVR to the matching black negative () terminals for each surround speaker. (Seepage 16 for more information on speaker polarity.)

Center Speaker Outputs:Connect these outputsto the matching + and terminals on your centerchannel speaker. In conformance with the CEAcolor-code specification, the green terminal is thepositive, or +, terminal that should be connected tothe red (+) terminal on speakers with the older color-coding. Connect the black () terminal on the AVR tothe black () terminal on your speaker. (See page 16for more information on speaker polarity.)

Optical Digital Audio Inputs:Connect the opticaldigital output from a DVD player, HDTV receiver, LDplayer or CDplayer to these jacks. The signal may be aDolby Digital signal, a DTS signal or a standard PCM

digital source. Component Video Monitor Outputs:Connect these outputs to the component video inputs of avideo projector or monitor. When a source connectedto one of theComponent Video Inputs isselected, the signal will be sent to these jacks.

Component Video 1 Inputs:Connect theY/Pr/Pb component video outputs of a DVD player,HDTV set-top converter, satellite receiver or othervideo source device with component video outputs tothese jacks.

Component Video 2 Inputs:Connect the

Y/Pr/Pb component video outputs of a DVD player,HDTV set-top converter, satellite receiver or othervideo source device with component video outputs tothese jacks.

See page 22 for information on assigning theComponent Video 1and 2 Inputs to theappropriate source inputs.

Fan Vents:These ventilation holes are the output of the AVR 340s airflow system. To ensure properoperation of the unit and to avoid possible damage to

delicate surfaces behind the AVR, make certain thatthese holes are not blocked and that there is at least 3 inches of open space between the vent holes andany other surface. It is normal for the fan to remain at most normal volume levels. An automatic temperture sensor turns the fan on only when it is needed.

a AC Power Cord:Connect the AC power cord toa non-switched AC wall outlet.

b Switched AC Accessory Outlet:These outletsmay be used to power any device you wish to haveturned on when the AVR 340 is turned on.

c Unswitched AC Accessory Outlet:This outlet may be used to power any AC device. The power wremain on at this outlet regardless of whether the

AVR 340 is on or off.

NOTE:The total power consumption of all devicesconnected to the accessory outlets should not exceed100 watts.

d Optical Digital Audio Output:Connect this jack to the optical digital input connector on a CD-R/RWMiniDisc or other digital recorder.

e Coaxial Digital Audio Output:Connect this jack to the coaxial digital input of a CD-R/RW, MiniDisc oother digital recorder.

f Coaxial Digital Audio Inputs:Connect the coaxdigital output from a DVD player, HDTV receiver,LDplayeror CD player to these jacks.The signal may be aDolby Digital signal, DTS signal or a standard PCM dsource. Do not connect the RF digital output of an L

player to these jacks.

g S-Video Monitor Output:If any of the input sources used in your system have S-video connec-tions to the AVR, connect this jack to the S-video inon your television, projector or other video display.

NOTE:Thanks to the AVR 340s cross-conversioncapability, if your video display device is equipped wcomponent (Y/Pb/Pr) video inputs, you need only toconnect theComponent Video Monitor Outputsto your display device, and the AVR 340 will automcally convert all composite and S-video source signto the component video format for display.You will

also be able to view the AVR 340s on-screen displausing just the component video connection, unless tsource device is a high-definition (720p, 1080i or1080p) video device, in which case you would thenneed to either switch to a 480p source or connect th

Video Monitor OutputY or theS-Video MonitorOutputP to your video display in order to view theon-screen displays.

h DVD S-Video Input:Connect the S-video output oa DVD player or other video source to this jack.

8/6/2019 AVR 340 OM(web)rev3-21-06

10/68

10 REAR-PANEL CONNECTIONS

REAR-PANEL CONNECTIONSREAR-PANEL CONNECTIONS

10 REAR-PANEL CONNECTIONS

i Video 1 S-Video Input:If the product connected tothe Video 1 Audio Inputsa has S-video capability,connect this jack to the PLAY/OUT S-video jack onthat unit and then make certain that theS-VideoMonitor Outputg is connected as described above.

j Digital Media Player (DMP) Connector:With the AVR 340 turned off, connect the optionalHarman Kardon to this connector. When theDigital Media Player source is selected,you may viewiPod control and navigation messages on your videodisplay (if one is connected to one of the VideoMonitor Outputsg Y ), and in theUpperandLowerDisplay LinesPQ . You may navigate the iPodand select tracks for playback using the / / / Buttonsno , theSet Buttonp andTransportControls` on your AVR remote. See page 42 formore information.

k Video 1 S-Video Output:If the product connectedto the Video 1 Audio OutputsY has S-video capa-bility, connect this jack to the REC/IN S-video jack onthat unit.

U Video 2 S-Video Input:If the product connectedto the Video 2 Audio Inputsc has S-video capabil-ity, connect this jack to the PLAY/OUT S-video jack on that unit and then make certain that theS-VideoMonitor Outputg is connected as described above.

V Video 2 S-Video Output:If the product connectedto the Video 2 Audio Outputsd has S-video capa-bility, connect this jack to the REC/IN S-video jack onthat unit.

W Video 3 S-Video Input:If the product connected tothe Video 3 Audio Inputse has S-video capability,connect this jack to the PLAY/OUT S-video jack onthat unit and then make certain that theS-VideoMonitor Outputg is connected as described above.

X 6/8-Channel Direct Inputs:These jacks areused for connection to source devices such asDVD-Audio or SACD players with discrete analogoutputs. Depending on the source device in use, alleight jacks may be used, though in many cases onlyconnections to the front left/right, center, surroundleft/right and LFE (subwoofer input) jacks will be usedfor standard 5.1 audio signals.

Y Video Monitor Output:Connect this jack to thecomposite video input of a TV monitor or video projec-tor to view the on-screen menus and the output of astandard video source.

NOTE:Thanks to the AVR 340s cross-conversioncapability, if your video display device is equipped withcomponent (Y/Pb/Pr) video inputs, you need only toconnect theComponent Video Monitor Outputsto your display device, and the AVR 340 will convert all composite and S-video source signals to component video.You will also be able to view the AVR 340son-screen displays using the component video connec-tion, unless the source device is high-definition (720por 1080i) video, in which case you should eitherswitch to a 480p source or connect the Videoor theS-Video Monitor OutputPY to your video displayto view the on-screen displays.

Z DVD Audio/Video Inputs:Connect the compositevideo and L/R analog audio outputs of a DVD player orother video source to these jacks.

a Video 1 Audio/Video Inputs:Connect the com-posite video and L/R analog audio PLAY/OUT jacks

of a VCR or other video source to these jacks.b Video 1 Audio/Video Outputs:Connect thecomposite video and L/R analog audio REC/IN jacksof a VCR or other video recording device such as aDVD recorder or PVR to these jacks.

c Video 2 Audio/Video Inputs:Connect the com-posite video and L/R analog audio PLAY/OUT jacksof a cable television box or other video source tothese jacks.

d Video 2 Audio/Video Outputs:Connect thecomposite video and L/R analog audio REC/IN jacksof a VCR or other video recording device such as a

DVD recorder or PVR to these jacks.

e Video 3 Audio/Video Inputs:Connect the com-posite video and L/R analog audio PLAY/OUT jacks of an HDTV tuner or other video source to these jacks.

f Tape Inputs:Connect these jacks to thePLAY/OUT jacks of an audio recorder.

g Tape Outputs:Connect these jacks to theRECORD/INPUT jacks of an audio recorder.

h AM Antenna Terminals:Connect the AM loopantenna supplied with the receiver to these terminals.If an external AM antenna is used, make connections

to the AMand GNDterminals in accordance withthe instructions supplied with the antenna.

NOTE ON VIDEO CONNECTIONS:When connectina video source product such as a VCR, DVD playsatellite receiver, cable set-top box, personal viderecorder or video game to the AVR 340, you mayuse either a composite or S-video connection, bunot both, for each source device.

The AVR 340 features cross-conversion capabilitenabling you to benefit from higher-quality viewiyour video sources, even those that use compositS-video switching, when connected to your videoplay with component video inputs.

TheBridgeTM

TheBridgeTM

8/6/2019 AVR 340 OM(web)rev3-21-06

11/68

MAIN REMOTE CONTROL FUNCTIONS 11

MAIN REMOTE CONTROL FUNCTIONS

a Power Off Buttonb IR Transmitter Windowc Program Indicatord Power On Buttone Input Selectorsf AVR Selectorg AM/FM Tuner Select h Dim Buttoni Test Buttonj Sleep Buttonk DSP Surround Mode Selectorl Night Modem Channel Select Buttonn / Buttonso / Buttonsp Set Buttonq Digital Select r Numeric Keyss Tuner Mode

t Direct Buttonu Tuning Up/Downv OSD Buttonw Dolby Mode Selectorx DTS Digital Mode Selectory Logic 7 Mode Select Buttonz Skip Up/Down Buttons` Transport ControlsR Stereo Mode Select ButtonS DTS Neo:6 Mode Select T Macro ButtonsU Disc Skip ButtonV Preset Up/DownW Clear Button

X Memory ButtonY Delay/Prev. Ch.Z Speaker Select a Multiroom Buttonb Volume Up/Downc TV/Video Selectord DMP Selectore 6-Channel/8-Channel Direct Input f Mute

TheBridgeTM

s

abc

de

f

gh

j

n

n

poo

q

r

t

v

`

32

30

29

28

36

37

38

39

z

x

35

POWER

MUTE

AVR DVD

AM/FM

CD TAPE

VID2VCR TVCBL/SAT

6/8 CH DMP

VID1 VID3 VID4The Bridge

OFFON

SLEEPT/V

SURR.CH. VOL.

G U I D E

C H .

E X I T

D I G I T A L

M E N U S P K R

P R E V

. C H . D E

L A Y

SET

1 2 3 4

765

9 0TUN-M MEM

M2 M3 M4

D.SKIP

M1

DIRECT

OSD

TUN ING

DOLBY S UR DTS SURR DTS NEO:6

STEREOLOGIC 7

SKIP UPDW N

PRESET

CLEAR

TEST

NIGHT M-ROOM

340

8

l

u

DIM

i

k

m

3433

w

y

4140

31

42

NOTES: The function names shown here are each buttons

feature when used with the AVR 340. Most buttonshave additional functions when used with otherdevices. See pages 5152 for a list of thesefunctions.

To make it easier to follow the instructions that referto this illustration, a larger copy may be down-loaded from the Product Support section for thisproduct at www.harmankardon.com.

8/6/2019 AVR 340 OM(web)rev3-21-06

12/68

MAIN REMOTE CONTROL FUNCTIONS

12 MAIN REMOTE CONTROL FUNCTIONS

IMPORTANT NOTE:The AVR 340s remote maybe programmed to control up to eight devices,includingthe AVR 340. Before using the remote, it isimportant toremember to press theInput SelectorButtone that corresponds to the unit you wishto operate.

The AVR 340s remote is shipped from the factory tooperate the AVR 340 and most Harman Kardon CD orDVD players and cassette decks. The remote is alsocapable of operating a wide variety of other productsusing the control codes that are part of the remote.Before using the remote with other products, follow theinstructions on page 48 to program the proper codesfor the products in your system.

It is also important to remember that many of the but-tons on the remote take on different functions, depend-ing on the product selected using the Device ControlSelectors. The descriptions shown here primarily detailthe functions of the remote when it is used to operatethe AVR 340. (See pages 4952 for information about alternate functions for the remotes buttons.)

a Power Off Button:Press this button to place the AVR 340 or a selected device in the Standby mode.

b IR Transmitter Window:Point this windowtowards the AVR 340 when pressing buttons on theremote to make certain that infrared commands areproperly received.

c Program Indicator:This three-color indicator isused to guide you through the process of program-ming the remote. (See page 48 for information onprogramming the remote.)

d Power On Button:Press this button to turn onthe power to a device selected by pressing one of theInput Selectors e .

e Input Selectors: Pressing one of these buttonswill perform three actions at the same time. First, if the

AVR 340 is not turned on, this will power up the unit.Next, it will select the source shown on the button asthe input to the AVR 340. Finally, it will change theremote control so that it controls the device selected.

After pressing one of these buttons you must pressthe AVR Selector Buttonf again to operate the

AVR 340s functions with the remote.f AVR Selector:Pressing this button will switch theremote so that it will operate the AVR 340s functions.If the AVR 340 is in the Standby mode, it will also turnthe AVR 340 on.

g AM/FM Tuner Select:Press this button to select the AVR 340s tuner as the listening choice. Pressingthis button when the tuner is already in use will select between the AM and FM bands.

h Dim Button:Press this button to activate theDimmer function, which reduces the brightness of thefront panel display, or turns it off entirely. The first pressof the button shows the default state, which is full bright-ness by indicatingVFD FULL in theLower

Display Line . Press the button again within fiveseconds to reduce the brightness by 50%, as indicatedbyVFD HALF showing in theLower Display Line . Press the button again within five seconds and themain display will go completely dark. Note that this set-ting is temporary, in that regardless of any changes, thedisplay will always return to full brightness when the AVRis turned on. In addition, thePower Indicator2 willalways remain at full brightness regardless of the setting.This is to remind you that the AVR is still turned on.

i Test Button:Press this button to begin thesequence used to calibrate the AVR 340s output levels.(See pages 25, 31 and 42 for more information oncalibrating the AVR 340.)

j Sleep Button:Press this button to place the unit in the Sleep mode. After the time shown in the display,the AVR 340 will automatically go into the Standbymode. Each press of the button changes the time untilturn-off in the following order:

See page 34 for more information on the SleepFunction. This button is also used to change channelson your TV when the TV is selected.

k DSP Surround Mode Selector:Press this but-ton to cycle through the DSP, VMAx and Stereo sur-round modes such as Hall, Theater,VMAx Near andFar, and Surround Off. This button is also used to tunechannels when the TV is selected using the deviceInput Selectore .

l Night Mode:Press this button to activate theNight mode. This mode is available in speciallyencoded digital sources, and it preserves dialogue(center channel) intelligibility at low volume levels.

m Channel Select Button:This button is used tostart the process of setting the AVR 340s output levelsto an external source. Once this button is pressed,usethe / Buttons n to select the channel beingadjusted,then press theSet Buttonp , followed bythe / Buttonsn again, to change the level set-ting. (See pages 31 and 42 for more information.)However, Harman Kardon recommends that you first perform the EzSet/EQ procedure, as described onpages 25 to 27.

n / Buttons:These multipurpose buttons aused to change or scroll through items in the on-screen menus, make configuration settings such adigital inputs or delay timing, or to select surrounmodes. When changing a setting, first press the b

for the function or setting to be changed (e.g., prethe DSP Surround Mode Selectork to select asound field mode or theDigital Select Buttonqto change a digital input) and then press one of thbuttons to scroll through the list of options or toincrease or decrease a setting. The sections in thimanual describing the individual features and funcontain specific information on using these buttofor each application.

o / Buttons:These buttons are used to chanthe menu selection or setting during some of the sprocedures for the AVR 340.

p Set Button:This button is used to enter settininto the AVR 340s memory. It is also used in thesetup procedures for delay time, speaker configurand channel output level adjustment.

q Digital Select:Press this button to assign oneof the digital inputs*( f to a source. (Seepages 22 and 38 for more information on selectindigital inputs.)

r Numeric Keys:These buttons serve as a 10-button numeric keypad to enter tuner preset positiThey are also used to select channel numbers whTV, Cable or SAT has been selected on the remoto select track numbers on a CD, DVD or LD pla

depending on how the remote has been programmI Tuner Mode:Press this button when the tuneis in use to select between automatic tuning andmanual tuning. When the button is pressed so thaMANUAL appears in theLower Display Line ,pressing theTuning Buttons9u will move thefrequency up or down in single-step increments.When the FM band is in use, pressing this button a stations signal is weak will change to monauralreception. (See page 41 for more information.)

J Direct Button:Press this button when the tunis in use to start the sequence for direct entry of astations frequency. After pressing the button, simpress the properNumeric Keysr to select a sta-tion. (See page 41 for more information on the tu

8/6/2019 AVR 340 OM(web)rev3-21-06

13/68

MAIN REMOTE CONTROL FUNCTIONS

MAIN REMOTE CONTROL FUNCTIONS 13

u Tuning Up/Down:When the tuner is in use,these buttons will tune up or down through the selectedfrequency band. If theTuner Mode Buttons&has been pressed so that AUTO appears in the on-screen display andLower Display Line , pressing

and holding either of the buttons for three seconds willcause the tuner to seek the next station with acceptablesignal strength for quality reception. WhenMANUALappears in theLower Display Line , pressing thesebuttons will tune stations in single-step increments. (Seepage 41 for more information.)

v OSD Button:Press this button to activate theOn-Screen Display (OSD) system used to set up oradjust the AVR 340s parameters.

w Dolby Mode Selector:This button is used toselect from among the available Dolby Surround pro-cessing modes. Each press of this button will select one of the Dolby Pro Logic II or IIx, or Dolby Virtual

Speaker modes or Dolby 3 Stereo. When a DolbyDigital-encoded source is in use, the Dolby Digitalmode may also be selected.When the headphonesare in use, this button selects from among the DolbyHeadphone modes. (See pages 3637 and 40 for theavailable Dolby surround mode options.)

x DTS Digital Mode Selector:When a DTS-encoded digital source is selected, each press of thisbutton will scroll through the available DTS modes.The specific choice of modes will vary depending onwhether the source material contains DTS-ES 6.1Discrete encoding. When a DTS source is not in use,this button has no function. (See pages 36 and 40 for

the available DTS digital options.)y Logic 7 Mode Select Button:Press this buttonto select from among the available Logic 7 surroundmodes. (See pages 36 and 40 for available Logic 7options.)

z Skip Up/Down Buttons:These buttons do not have a direct function with the AVR 340, but whenused with a compatibly programmed CD or DVD play-er they will change to the next or previous track.

` Transport Controls:These buttons do not haveany functions for the AVR 340, but they may beprogrammed for the forward/reverse play operationof a wide variety of CD or DVD players, and audio orvideo cassette recorders. When the DMPsource is in use, these buttons may be used to oper-ate some functions on a compatible iPod if it isdocked in The Bridge. See page 42 for moreinformation on using .

When the remote is used to control the AVR, or theVID2 or VID3 device, by default these buttons are pro-grammed to operate the DVD player. However, youmay use the Transport Control Punch-Through featuredescribed on page 50 to program these buttons tooperate another devices transport controls when the

AVR, VID2 or VID3 has been selected.

R Stereo Mode Select Button:When the buttonis pressed so that SURROUND OFF appears inthe Lower Display Line , with only theSurr OffSurround Mode Indicator lit, the AVR will oper-ate in a bypass mode with true, fully analog, two-chan-nel left/right stereo mode with no surround processingor bass management, unlike other modes where digi-tal processing is used. When the button is pressed sothat SURROUND OFF appears in theLowerDisplay Line , with both theDSPand Surr OffSurround Mode Indicators lit, you may enjoy atwo-channel presentation of the sound along with thebenefits of bass management. Depending on whetheryour system is configured for 5.1 or 6.1/7.1 chan-nels, the next press of the button will cause either5 CH STEREO or 7 CH STEREO toappear, and the stereo signal will be routed to all five(or seven) speaker channels. (See pages 37 and 40for more information on stereo playback modes.)

S DTS Neo:6 Mode Select:Press this button toselect a DTS Neo:6 mode. These modes take a two-channel stereo- or matrix surround-encoded sourceand create a full five-, six- or seven-channel soundfield. (See pages 36 and 40 for the DTS Neo:6options.)

T Macro Buttons:Press these buttons to store orrecall a Macro, which is a preprogrammed sequenceof commands stored in the remote. (See page 48 formore information on storing and recalling macros.)

U Disc Skip Button:This button has no direct function for the AVR 340 but is most often used tochange to the next disc in a CD or DVD player whenthe remote is programmed for that type of device.(See page 49 for more information on using theremote with products other than the AVR 340.)

V Preset Up/Down:When the tuner is in use,press these buttons to scroll through the stations

programmed into the AVR 340s memory. Whensome source devices, such as CD players, VCRs andcassette decks, are selected using the deviceInputSelectors e , these buttons may function asChapter Step or Track Advance.

W Clear Button:Press this button to clear incorrect entries when using the remote to directly enter a radiostations frequency.

X Memory Button:Press this button to enter a radiostation into the AVR 340s preset memory. First, tune

the desired station, and then press this button. Twounderline indicators will flash at the right side of theUpper Display LineP , and within five secondspress theNumeric Keysr for the preset numberbetween 01 and 30 that you wish to assign to thestation. (See page 41 for more information.)

Y Delay/Prev Ch.:Press this button to beginthe process for setting the delay times used by the

AVR 340 when processing surround sound. Afterpressing this button, the delay times are entered bypressing theSet Buttonp and then using the / Buttons n to select A/V SYNCDELAY or the delay setting for any available channel. Press theSet Buttonp , and then use the / Buttons n to change the setting. Press theSet Buttonp again to complete the process. (Seepage 30 for more information.) However, we recommend that you first perform the EzSet/EQ procedureas described on pages 2527.

Z Speaker Select: Press this button to beginthe process of configuring the AVR 340s bass management system for use with the type of speakersused in your system. Once the button has beenpressed, use the / Buttons n to select thechannel you wish to set up. Press theSet Buttonp and then use the / Buttons n to select the appropriate speaker size. Press theSet Buttonp to enter the new setting, and then use the / Buttons n again to select another channel toconfigure. When all adjustments have been compress the Set Button p twice to exit the settingsand return to normal operation. (See page 28 for

more information.) However, Harman Kardon recommends that you first perform the EzSet/EQ proceduras described on pages 2527.

a Multiroom Button:Press this button to beginthe process of activating the Multiroom system, orchanging the source input or volume level for theremote zone. Press the Buttons n to scrollto the on/off, source input or volume level setting, athen press theSet Buttonp to access the desiredsetting. Use the Buttons n to scroll throughthe options, and theSet Buttonp to select. (Seepage 46 for information on the Multiroom system.)

b Volume Up/Down:Press these buttons to raiseor lower the system volume. By default, the VolumeUp/Down Buttonsb are programmed at the fac-tory to control the AVR 340s volume, no matter whsource device has been selected (except TAPE). Youmay reprogram these buttons to control the volume another device, such as your TV, using the VolumeControl Punch-Through instructions found onpage 50.

c TV/Video Selector:This button does not have adirect function on the AVR 340, but when used with

TheBridgeTM

TheBridgeTM

8/6/2019 AVR 340 OM(web)rev3-21-06

14/68

compatible VCR, DVD or satellite receiver, pressing thisbutton will switch between the output of the deviceand the external video input. Consult the owners man-ual for your specific player or receiver for the details of how it implements this function.

d Digital Media Player (DMP)Selector:When Harman Kardons (optional) is con-nected to Digital Media Player (DMP)Connector j and a compatible iPod is docked in

, pressing this selector will select the iPodas the audio source input device for the AVR 340. Inaddition, if a video display is connected to one of the

Video Monitor Outputsg Y , the iPods messageswill appear on screen, and in theUpperand LowerDisplay LinesPQ . The / / / Buttonsno , the Set Button p and theTransportControls` may be used to navigate the iPod andto operate many functions. See page 42, and themanuals for The Bridge and your iPod for moreinformation.

e 6-Channel/8-Channel Direct Input:Pressthis button to select the device connected to the6/8-Channel Direct InputsX . (See page 34 formore information.)

When the device connected to the6/8-ChannelDirect InputX is also a video source, such as aDVD or DVD-Audio player with an onboard audiodecoder, you must first select that video source bypressing itsInput Selectore , then press thisbutton to choose the device connected to the6/8-Channel Direct InputX as the audio source. Notethat if you desire, you may select any video source tobe used in conjunction with the6/8-Channel DirectInput X as the audio source.

f Mute: Press this button to momentarily silencethe AVR 340 or TV set being controlled, depending onwhich device has been selected. When the AVR 340remote is being programmed to operate another device,this button is pressed with theInput Selector Buttone to begin the programming process. (See page48 for more information on programming the remote.)

TheBridgeTM

TheBridgeTMTheBridgeTM

TheBridgeTM

MAIN REMOTE CONTROL FUNCTIONS

14 MAIN REMOTE CONTROL FUNCTIONS

8/6/2019 AVR 340 OM(web)rev3-21-06

15/68

ZONE II REMOTE CONTROL FUNCTIONS

Power Off Button:When used in the roomwhere the AVR 340 is located, press this buttonto place the unit in Standby. When it is used in aremote room with a sensor that is connected to theMultiroom IR Input Jack , this button turns the

Multiroom system on and off. AVR Selector:Press this button to turn onthe AVR 340 and to access the volume and mutecontrols.The input in use when the unit was last onwill be selected.

AM/FM Tuner Selector:Press this button toselect the Tuner as the input to the Multiroom system.Press it again to change between the AM and FMbands. Pressing this button will also turn on the

AVR 340s multiroom system if it is off, even whenthe AVR is in Standby mode.

Input Selectors:Press one of these buttons toselect a specific input. Pressing this button will alsoturn on the AVR 340s multiroom system if it is off,even when the AVR is in Standby mode.

Preset Up/Down Track Skip Buttons:Whenthe AVR 340s tuner is selected as the input source,these buttons will move up or down through the list of stations that have been stored in the preset memory.When a CD or DVD changer or player is selected,these buttons activate the Forward or Reverse Track or Chapter Skip functions.

Disc Skip Buttons:Press these buttons tochange discs on compatible Harman Kardon CD or

DVD changers or players. When DMP hasbeen selected, the left () button has the same effect as scrolling the iPods Click Wheel counterclockwise,and the right (+) button has the same effect asscrolling the Click Wheel clockwise.

Volume Up/Down Buttons:When the Zone IIremote is used in the room where the AVR 340 islocated, press this button to raise or lower the volumin that room. When it is used in a remote room withsensor that is connected to theMultiroom IR Input

Jack , this button will raise or lower the volume the remote room.

Pause Button: Press this button to activate thePause function on compatible Harman Kardon CD,DVD or cassette deck products, or on your iPod whDMP has been selected.

Stop Button:Press this button to activate theStop function on compatible Harman Kardon CD, Dor cassette deck products. It will have no effect onyour iPod when DMP has been selected.

Play Button:Press this button to activate thePlay function on compatible Harman Kardon CD,DVD or cassette players or on your iPod when DM

has been selected.

Tuning Up/Down Fast Play Buttons:Whenthe Zone II remote is used in the same room as the

AVR 340, these buttons may be used to change thefrequency of the tuner. These buttons may also contthe Fast Play or Fast Reverse functions of compatibHarman Kardon CD, DVD or cassette decks in thesame room, or from a remote room when an IR linkis connected to the AVR 340. These buttons willselect the previous or next track on your iPod whenDMP has been selected.

Mute Button:When the Zone II remote is usedin the room where the AVR 340 is located, press thbutton to temporarily silence the unit. When it is usin a remote room with a sensor that is connectedto the Multiroom IR Input Jack , this buttonwill temporarily silence the feed to the remote roomonly. Press the button again to return to the previouvolume level.

TheBridgeTM

TheBridgeTM

TheBridgeTM

I

TheBridgeTM

TheBridgeTM

Power Off Button AVR Selector AM/FM Tuner Selector Input Selectors Preset Up/Down Track Skip Buttons Disc Skip Buttons Volume Up/Down Buttons Pause Button

Stop Button Play Button Tuning Up/Down Fast Play Buttons Mute Button

I

POWER

OFF

MUTE

AVR

AM/FM

VID 1

CD

DMP/The Bridge

VOLUME

PLAY

SKIP

TUNINGPRESET

VID 2

G

A

B

C

D

E

F

H

I

K

J

.2

L

DVD

VID 3 VID 4

TAPE

DISC

SKIP

DISC

NOTES: The Zone II remote may be used in either the same room where the AVR 340 is located or in a separate

room with an optional infrared sensor or A-BUS product that is connected to the AVR 340sMultiroom IR InputJack . When it is used in the same room as the AVR 340, it will control the functions of the AVR 340compatible Harman Kardon products in that room. When it is used in a separate room via a sensor connethe Multiroom IR Input Jack , the buttons for Power, Input Source, Volume and Mute will control the sand volume for the second zone, as connected to theMultiroom Audio Output Jacks . (See page 46 forcomplete information on using the Multiroom system.)

To make it easier to follow the instructions that refer to the controls and connectors in this illustration, a lcopy may be downloaded from the Product Support section for this product at www.harmankardon.com.

ZONE II REMOTE CONTROL FUNCTIONS 15

8/6/2019 AVR 340 OM(web)rev3-21-06

16/68

INSTALLATION AND CONNECTIONS

System Installation After unpacking the unit, locating it in a place with ade-quate ventilation and placing it on a solid surface capableof supporting its weight, you will need to make the con-nections to your audio and video equipment.

IMPORTANT NOTE:For your personal safety and toavoid possible damage to your equipment and speakers,it is always a good practice to turn off and unplug the

AVR and ALL source equipment from the AC outlet before making any audio or video system connections.

Audio Equipment ConnectionsWe recommend that you use high-quality interconnect cables when making connections to source equipment and recorders to preserve the integrity of the signals.

1. Connect the analog outputs of a CD player to theCD Audio Inputs .

NOTE:When the CD player has both fixed andvariable audio outputs, it is best to use the fixedoutput unless you find that the input to the receiveris so low that the sound is noisy, or so high that it is distorted.

2. Connect the analog Play/Out jacks of a cassettedeck, MD, CD-R or other audio recorder to theTape Input Jacks f . Connect the analogRecord/In jacks on the recorder to theTapeOutput Jacks g on the AVR 340.

3. Connect the output of any digital sources such asa CD or DVD changer or player, advanced videogame, a digital satellite receiver, HDTV tuner ordigital cable set-top box or the output of a com-patible computer sound card to theOpticalandCoaxial Digital Audio Inputsf *( . Werecommend connecting the coaxial digital audiooutput of your DVD player to theCoax 1 Digital

Audio Inputf , since that digital input isassigned to the DVD source by default. The Video2/Cable/Sat source defaults to theOptical 1Digital Audio Input . If your cable televisionset-top box or satellite receiver is equipped withan optical digital audio output, we recommend that you connect it to this input to obtain the benefitsof higher-quality digital audio (such as PCM, DolbyDigital 2.0 or Dolby Digital 5.1 signals when broad-cast by your cable or satellite provider).

NOTE:If you wish for your digital source device tobe available for use by the multiroom system, you willneed to connect its analog audio outputs to the appro-priate inputs on the AVR 340, as the multiroom sys-tem is not capable of distributing digital signals to theremote zone.

4. Connect theCoaxialor Optical Digital AudioOutputsde on the rear panel of the AVR 340 to

the matching digital input connections on a CD-R orMiniDisc or other digital recorder.

5. Assemble the AM Loop Antenna supplied with theunit so that the tabs at the bottom of the antennaloop snap into the holes in the base. Connect it tothe AM Antenna Terminalsh .

6. Connect the supplied FM antenna to theFM(75-ohm)Connection . The FM antenna may be anexternal roof antenna, an inside powered or wire-lead antenna or a connection from a cable TV sys-tem. If the antenna or connection uses 300-ohm

twin-lead cable, you must use an optional 300-ohm-to-75-ohm adaptor to make the connection.

7. With the AVR 340 turned off, connect the optionalHarman Kardon to Digital MediaPlayer (DMP) Connectorj . Your compatibleiPod may be docked in when you wish touse it as an audio source device. Video materialsstored on the iPod may not be viewed via .

8. Connect the front, center, surround and surroundback speaker outputs to the respec-tive speakers.

To ensure that all the audio signals are carried to your

speakers without loss of clarity or resolution, we sug-gest that you use high-quality speaker cable. Manybrands of cable are available and the choice of cablemay be influenced by the distance between yourspeakers and the receiver, the type of speakers youuse, personal preferences and other factors. Your dealeror installer is a valuable resource to consult in select-ing the proper cable.

Regardless of the brand of cable selected, we recom-mend that you use a cable constructed of multistrandcopper with a gauge of 14 or smaller.Remember that in specifying cable, the lower the number, the thickerthe cable.

Cable with a gauge of 16 may be used for short runsof less than 10 feet. We do not recommend that youuse cables with an AWG equivalent of 18 or higher,due to the power loss and degradation in performancethat will occur.

Cables that are run inside walls should have the appro-priate markings to indicate listing with UL, CSA or otherappropriate testing agency standards. Questions about running cables inside walls should be referred to yourinstaller or a licensed electrician who is familiar with

the NEC and/or the applicable local building codeyour area.

When connecting wires to the speakers, observeproper polarity. Note that the positive (+) terminaeach speaker connection may carry a specific colcode, as noted on page 8. However, many speakestill use a red terminal for the positive (+) connecConnect the negative or black wire to the samminal on both the receiver and the speaker.

NOTE:While most speaker manufacturers adherean industry convention of using black terminals fnegative and red ones for positive, some may varfrom this configuration. To ensure proper phase aoptimal performance, consult the identification plyour speaker or the speakers manual to verify poIf you do not know the polarity of your speaker, ayour dealer for advice before proceeding, or consthe speakers manufacturer.

We also recommend that the length of cable useto connect speaker pairs be identical. For examuse the same length piece of cable to connect thfront-left and front-right or surround-left and suround-right speakers, even if the speakers are adifferent distance from the AVR 340.

9. The connections to a subwoofer are normallymade via a line-level audio connection from Subwoofer Output to the line-level input subwoofer with a built-in amplifier. When a psubwoofer is used, the connection first goes tpower amplifier, which will be connected to

or more subwoofers. If you are using a powesubwoofer that does not have line-level inputnections, follow the instructions furnished wispeaker for connection information.

10. If an external multichannel audio source with6.1 or 7.1 outputs such as an external digitalprocessor/decoder, DVD-Audio or SACD plais used, connect the outputs of that device tothe 6/8-Channel Direct InputsX .

Video Equipment ConnectionsVideo equipment is connected in the same manneraudio components. The use of high-quality intercocables is recommended to preserve signal quality.

1. Connect a VCRs, DVD recorders, personal virecorders or other video sources audio and viPlay/Out jacks to the Video 1 Audio / Videoand/orS-Video Input JacksRa on the rear panel. T

Audio and Video Record/In jacks on the recordshould be connected to the Video 1 Audio/Videand/orS-Video Output JacksTb on the AVR 3

Although any video device may be connected these jacks, we recommend connecting your virecorder to take advantage of the fact that the

TheBridgeTM

TheBridgeTM

TheBridgeTM TheBridgeTM

16 INSTALLATION AND CONNECTIONS

INSTALLATION AND CONNECTIONS

8/6/2019 AVR 340 OM(web)rev3-21-06

17/68

INSTALLATION AND CONNECTIONS 17

remote control is preprogrammed with videorecorder product codes for the Video 1 device.

2. Connect the analog audio and video outputs of a satellite receiver, cable TV converter, televisionset or any other video source to the Video 2

Audio/Video and S-Video Input JacksUc . Although any video device may be connected tothese jacks, we recommend connecting your cableTV converter or satellite receiver to take advantageof the fact that the remote control is prepro-grammed with the product codes of these devicetypes for the Video 2 device.

3. Connect the analog audio and video outputs of a television or other video device to the Video 3

Audio/Videoand S-Video Input JacksWe onthe rear panel. Although any video or audio devicemay be connected to these jacks, we recommendconnecting your television so that you may take

advantageof the fact that the remote control ispreprogrammedwith TV product codes for theVideo 3 device.

Important:If you are using the television only as adisplay device (i.e., if you receive your TV programsthrough a cable box or satellite receiver), do not connect the televisions outputs to the Video 3

Audio/Videoand S-Video Input JacksWe ,or to any other inputs on the AVR 340.

4. Connect the analog audio and video outputs of aDVD or laser disc player to theDVD Audio/Videoand S-Video Inputsh Z .

5. Connect the digital audio outputs of a DVD player,satellite receiver, cable box or HDTV converter tothe appropriateOpticalor Coaxial Digital Inputsf *( . Remember that the DVD sourcedefaults to theCoaxial 1 Digital Inputf , andthe Video 2/Cable/Sat source defaults to theOptical 1 Digital Audio Input . All othersources default to their analog inputs, althoughany source may be assigned to any digital audioinput on the receiver.

NOTE:When connecting a device such as a digitalcable box or other set-top tuner product with a digi-tal audio output, we recommend that you connect both the digital and analog outputs of the product toyour AVR. The audio input polling feature of the AVRwill then be able to make certain that you have aconstant audio feed, since it will automatically switchthe audio input to the analog jacks if the digitalfeed is interrupted or if it is not available for aparticular channel.

6. Connect the Video and/or S-Video MonitorOutputg Y jacks on the receiver to the compos-

ite or S-video input of your analog television moni-tor or video projector.

7. If both your video display monitor and at least onevideo source device (such as a DVD player orHDTV set-top box) are equipped with component video capability, then you may connect the compo-nent video outputs of the device to one of the twoComponent Video Inputs . In that case,you will not need to connect the Video MonitorOutputY or theS-Video Monitor OutputPto your video display, as the AVR 340 will convert composite and S-video signals to component video. This means you only have to connect onecable from the AVR to the video display. You willalso be able to view the AVR 340s on-screenmenu displays using just the component video con-nection, unless the source device is high-definition(720p or 1080i) video, in which case you shouldeither switch to a 480p source or connect the

Video Monitor OutputY or theS-VideoMonitor OutputP to your video display toview the on-screen displays.

8. It is recommended that you connect a DVD playeror a digital video recorder to theComponent

Video 1 Inputs , as this input is assigned to theDVD, CD, Tuner and Tape sources by default. Thus,whenever any of these sources is selected, youmay view the component video output of the deviceconnected to theComponent Video 1 Inputs ,enabling you to view and listen to different sources.

8. Similarly, it is recommended that you connect any

other audio/video device equipped with component video outputs, such as a DVD-Audio or SACD player,or HDTV set-top box, to the Video 1, Video 2 orVideo 3sources, or the 6-/8-channel direct inputs,as the Component Video 2 Inputs areassigned to the Video 1, Video 2, Video 3 and6-/8-channel source audio inputs by default.

8. However, you may connect any component videosource to either set of component video inputs, asthey are assignable to any source, following theinstructions on page 22. You will still need to con-nect either the analog or digital audio outputs, orthe 6-/8-channel audio outputs, of your component

video device to the analog audio inputs correspon-ding to the source (such as DVD or Video 2 for acable converter box), or to any of theOpticalorCoaxial Digital Audio Inputsf *( .

8. If the component video inputs are used, connect the Component Video Monitor Outputs tothe component video inputs of your TV, projectoror display device. You will also be able to view yourcomposite and S-video sources through this con-nection, benefiting from the higher quality andsuperior appearance of component video.

9. If you have a camcorder, video game or otheraudio/video device that is connected to the AVR oa temporary rather than permanent basis, connectthe audio, video and digital audio outputs of that device to the Video 4 Inputs*( on thefront panel. A device connected here is selected athe Video 4 input, and the digital inputs must beassigned to the Video 4 input. (See page 22 formore information on input configuration.)

8. NOTE:The AVR 340 is shipped with two coversthat may be installed over the front-panel input

jacks when they are not in use.

10. When connecting the AVR 340 to a digital-readHDTV-compatible or high-definition display(which is any device capable of accepting aninput signal of 480P or higher), you are able totake advantage of the units advanced video processing circuitry which converts all video signal

a 480P output. Since the AVR 340 displays theon-screen menus with upconverted video, theconnection from the AVR 340 to the display neeonly be one set of Y/Pr/Pb component videoto the Component Video Monitor Output .

11. When connecting the AVR 340 to a standard,analog video display that has standard compositand S-video inputs only, component video inputmay not be used. In this case, connect the Videoand S-Video Monitor OutputsPY to thematching composite and S-video inputs on yourvideo display, depending on which types of videare used by your source devices. If both types o

video are used by different source devices, thanboth Video Monitor OutputsPY must beseparately connected to your television.

VIDEO CONNECTION NOTES: When the component video jacks are used, the on

screen menus are not visible with high-definitionvideo (720p or 1080i), and you must switch to thstandard composite or S-video input on your TV,to a 480p video source, to view them.

When source devices such as a progressive scanDVD player or an HDTV set-top box are connectto the AVR 340 via component video connectionsyou wish to take advantage of the record outputs o

have video routed to a second room, it is also necessary to connect the standard, composite or S-video outputs of the source device to the AVR 340The record outputs and multiroom system cannot accept component inputs, nor are component inpudown-converted for use with these outputs.

When connecting a video source to the AVR 340,you may use either composite, component orS-video, but only one type of video may be con-nected for each device.

INSTALLATION AND CONNECTIONS

8/6/2019 AVR 340 OM(web)rev3-21-06

18/68

18 INSTALLATION AND CONNECTIONS18 INSTALLATION AND CONNECTIONS

System and Power ConnectionsThe AVR 340 is designed for flexible use with multi-room system and external control components.

Remote Infrared (IR) Control of the AVR orSource DevicesIf the receiver is placed behind a solid or smokedglass cabinet door, the obstruction may prevent theremote sensor from receiving commands. In thisevent, an optional remote sensor may be used.Connect the output of the remote sensor to theRemote IR Input jack.

If other components are also prevented from receivingremote commands, only one sensor is needed. Simplyuse this units sensor or a remote eye by running aconnection from theRemote IR Output jack tothe Remote IR Input jack on Harman Kardon or othercompatible equipment.

When controlling non-Harman Kardon source devices,the device may require the full carrier signal embed-ded within the IR command, rather than the strippedsignal used by Harman Kardon and many otherdevices. In these cases you may need to connect theRemote IR Carrier Output to the remote IR input of your device (or to an optional, external IR blaster),rather than using the standardRemote IR OutputJack . If you are in doubt as to which IR Output

jack to use for the equipment in your system, contact your dealer or installer, or consult the manufacturerssupport site and ask whether the unit to be controlleduses full carrier or stripped carrier IR commands.When full carrier commands are used, make the

connection to theRemote IR Carrier Output .Otherwise, make the connection to theRemote IROutput Jack .NOTE: All remotely controlled components must belinked together in a daisy chain. Connect the IR OUT

jack of one unit to the IR IN of the next to establishthis chain.

Multiroom ConnectionsThe AVR 340 is equipped with multizone capabilitiesthat allow it to send a separate audio source to theremote zone from the one selected for use in themain room.

Depending on your systems requirement, threeoptions are available for audio connection:

Option 1:Use high-quality, shielded audio intercon-nect cable from the AVR 340s location to the remoteroom. In the remote room, connect the interconnect cable to a stereo power amplifier. The amplifier will beconnected to the rooms speakers. At the AVR 340,plug the audio interconnect cables into theMultiroom

Audio Outputs on the AVR 340s rear panel.

Option 2:Connect theMultiroom Audio Outputs on the AVR 340 to the inputs of an optionalstereo power amplifier. Run high-quality speaker wirefrom the amplifier to the speakers in the remote room.

Option 3:Taking advantage of the AVR 340s built-in

seven-channel amplifier, it is possible to use two of theamplifier channels to power speakers in the remoteroom. When using this option, you will not be able touse the full 7.1-channel capabilities of the AVR 340 inthe main listening room, but you will be able to addanother listening room without external power ampli-fiers. To use the internal amplifiers to power a remotezone, connect the speakers for the remote room loca-tion to theSurround Back/Multiroom SpeakerOutputs . Before using the remote room, you willneed to configure the amplifiers for surround operationby changing a setting in theMULTI ROOMSETUP menu, following the instructions shownon page 46.

NOTE:The AVR 340s multiroom system is only capa-ble of distributing analog audio sources to the remotezone. Therefore, when connecting your digital audioequipment (e.g., CD or DVD players) as described onpage 16, make sure to use both analog and digitalaudio connections to ensure that the devices will beavailable to the multiroom system.

IR Control Fr