Upload
dangnhu
View
216
Download
2
Embed Size (px)
Citation preview
INSTALLATION INSTRUCTIONS FOR PART ASWC
IGNI
TION
TERM
INAL
S
WIR
ECU
TTERM3.
5
M2.
6M
3M
5
M4
ISO
62.
51.
5
KIT FEATURES
• OneInterfacedoesitall-Noadditionalinterfacesneeded• Designedtobecompatiblewithallmajorradiobrands• Autodetectsvehicletype,radioconnection,andpresetscontrols• Canbemanuallyprogrammedformostvehicles• Memoryretainssettingsevenafterbatterydisconnectionor
interfaceremoval• Connectionplacementsareallorganizedbehindtheradio• USBupdatable
INTERFACE COMPONENTS
•ASWCInterface•12-pinharnesswithmale3.5mmconnector•Female3.5mmconnectorwithBrownandBrown/Whitewires
•12k-ohmresistor
TOOLS REQUIRED
•Cuttingtool•Crimpingtool•Tape•Connectors(example:butt-connectors,bellcaps,etc.)
Axxess Steering Wheel Control Interface Installation Manual
ASWC
Introduction to the ASWC Interfaceand Wiring Harness
OnthetopoftheASWCinterfacetherearethreepointsofinterest:
1) Theprogramming LED–flashesrapidlywheninautodetectmode,flashesslowlyinmanualprogrammingmode.
2) Thereset button–Holddownbuttonfor3secondstostartautodetectmode;holddownlongerthen10secondstostartmanualprogrammingmode.
3) Theslide cover(USBPortCover)–OpenthisuptorevealtheUSBupdateport.UsingtheUSB-CABupdatecableandtheAxxesswebsiteyoucanmakesureyoualwayshavethelatestupdatedinventory.
Overview
USBPortCover ResetButton ProgrammingLED
Overview
Pin-1 PinkPin-2 White/GreenPin-3 Yellow/GreenPin-4 Green/OrangePin-5 Gray/RedPin-6 BlackPin-7 Blue/Pink
Pin-8 Black/GreenPin-9 Red(tip of 3.5 mm
connector)
Pin-10 White
(ring of 3.5 mm connector)
Pin-11 Gray/Blue
Pin-12 Red
Section 1: Installation
Installing the ASWC
1) ConnecttheBlackwireoftheASWCtoground.Youmayusethesamegroundingpointastheaftermarketradio.
2) ConnecttheRedwireoftheASWCtoa12-voltaccessorywire,onethatturns“on”and“off”withtheignitionkey.
3) LocatethecorrectSWCwire(s)inthevehicle’sradioprimaryorsecondaryharnessasdescribedinthevehicleinformationsheetfoundontheAxxesswebsite.Connectthecorrectwirecolor(s)fromtheASWCtothesteeringwheelcontrolwire(s)inthevehicle.
Note: Metra recommends that the wire(s) are soldered for the best and most secure connection. T-Taps or scotch locks are not recommended due to the higher chance of an intermitted connection or change in resistive values.
Section 1: Installation
4) IfyouareusinganEclipse,Kenwood,MetraOE,oranewerJVCradio,plugtheincludedfemale3.5mmconnectorwiththeBrown
andBrown/Whitewiresintothemale3.5mmconnectoroftheASWCharness.
• For Kenwood and select JVC: ConnecttheSWCwire(normallyBlue/Yellow)totheBrownwireoftheASWC.IsolateandtapetheBrown/Whitewire,itwillnotbeused.
Note: Some newer Kenwood radios will auto detect as a JVC. If this is the case, you can use a 12k-ohm resistor (included) in line between the Blue/Yellow and Brown wire of the female 3.5 mm jack during programming only. Or you can manually set the radio type which is in the radio programming section of this manual.
• For Eclipse:ConnecttheEclipseSWCwires(normallyBrown
andBrown/Black)totheBrownandBrown/WhitewiresoftheASWC. BrowngoestoBrownandBrown/WhitegoestoBrown/Black.Sometimesthisisreversed,reversethewiresifneeded.
• For Metra OE: ConnecttheSWCKey1wire(Gray)totheBrown
wireoftheASWC.
5) Forallotherradios,pluginthemale3.5mmconnectoroftheASWCintothebackoftheaftermarketradio,designatedforanexternalSWCcontrolinterface.Ifindoubtwherethe3.5mmconnectoroftheASWCgoespleaserefertotheaftermarketradiomanual.Onceallconnectionshavebeenmade,plugintheaftermarketradioifnotdonealready.
TheASWCcanbeprogrammedintwoways.(1)ItcandoitbyitselfthroughAutoDetectMode,or(2)itcanbemanuallyprogrammedinnon-datavehicles.ItisstronglyrecommendtostartwiththeAutoDetectModefirst.
Auto Detect Mode: Overview
TheASWChastheabilitytoautodetectcertainvehiclesandtoknowwhataftermarketradioitisconnectedto.
FortheAutoDetectfeaturetoworkthereare3possibleactions,howeveronlyoneactionwillberequiredbyyoudependingonyourvehicle:
• Turntheignitiononandnootheractionisrequired.
• Turntheignitionon,pressandholdthe“VolumeUp”buttononthesteeringwheel.
--- Or ---
• Turntheignitionon,pressandreleasethe“VolumeUp”buttonrepeatedlyonthesteeringwheel.
Asstatedbefore,onlyoneoftheseactionswillneedtobedonedependingonyourvehiclefortheAutoDetectfeaturetowork.PleaserefertothevehicleinfosheetprovidedontheAxxesswebsite.
Auto Detect Mode: Steps
1) Completeconnectionstothevehicleandtheaftermarketradio.
IfthisisthefirsttimetheASWCisbeinginstalledinavehicle:
2) Turntheignitionon;theLEDwillstartflashingrapidlywhichmeans
Section 2: Programming
theASWCislookingforthevehicleandtheradio.Gotostep4.
--- Or ---
IftheASWCwasinstalledinavehiclepreviously:
2) Turntheignitionon,theLEDwillflashonce,thengoout.
3) Holddowntheresetbuttonfor3secondsandthenreleaseit.
4) Performactionrequiredforyourparticularvehicleasnotedinthevehicleinfosheet.
5) AfteracoupleofsecondstheLEDshouldstopflashingandnotlightupfor2seconds.Atthispointdonotpushanybuttons.
6) Afterthe2secondstherewillbeaseriesof7flashes,someshortandsomelong.
7) TheLEDwillpauseforanother2secondsthenflashupto11times(refertoASWCledgend).
8) Thisistheendoftheautodetectionstage.IftheASWCdetectedthevehicleandtheradiosuccessfullytheLEDwilllightupsolidred.
9) ForvehicleswithOEBluetoothbuttonspleasepress“Hangup”or“Pickup”onyoursteeringwheelcontrolaftertheLEDontheASWCgoessolid.IftheOEBluetoothbuttonsareabletobeused,theLEDwillgooutafter3seconds.YourOEBluetoothbuttonsarenowprogrammedtoyouraftermarketradiosBluetoothbuttons(aftermarketradiomusthaveBluetoothcapabilities).
Tip: If the LED does not light up solid red refer to the troubleshooting section.
10)Makesurethesteeringwheelcontrolbuttonsfunctioncorrectlyinthevehicleandenjoy.
Section 2: Programming
Auto Detect Mode
SoyoutriedtheautodetectfeatureandattheendtheLEDdidnotstaysolidred.Insteaditstartedflashing,meaningthattheASWCdidnotdetectthevehicle.
Followthesestepstodeterminewhatmayhavehappened:
1) Verifythatyouhave12-voltaccessoryandagoodgroundtotheASWC.Sometimesthefactorygroundisnotsufficient,achassisgroundishighlyrecommended.IfyourvehiclehasaSWCreferencegroundwire,chassisgroundthataswell,alongwithyouraftermarketradio.
2) Validateusingthevehicleinformationsheet(Axxesswebsite)thatthecorrectsteeringwheelcontrolwire(s),inthevehicle,wereconnectedtothecorrectwire(s)totheASWC.
3) Confirmthatthe3.5mmconnectorisconnectedtoyourradiosecurelyandinthecorrectlocation.
4) Ifusingthefemale3.5mmconnectorinEclipse,Kenwood,selectJVC,orMetraOEradiosverifythattheradio’sSWCwireisconnectedtothecorrectwiretotheASWC.
Section 3: Troubleshooting
Note: Not every radio will have all the possible SWC commands on the steering wheel. Aftermarket radios that do not have Bluetooth will not recognize the PTT (Push To Talk) or “On/”off” Hook” commands; however those buttons can be manually programmed to do other commands in some cases. Please refer to the radio owner’s manual or wireless remote for specific commands that the radio will recognize.
1) Completeconnectionstothevehicleandtotheaftermarketradio,makesurethe3.5mmconnectorisconnected.
IfthisisthefirsttimetheASWCisbeinginstalledinavehicle:
2) Turntheignitionon;theLEDwillstartflashingrapidly.
3) After10secondstheASWCwillgointotheLEDfeedbackmode.AftertheseriesofLEDflashestheLEDwillstayinaslowconstantflashstate.Gotostep4.
--- Or ---
IftheASWChasbeeninavehiclebefore:
2) Pressandholdtheresetbuttondownformorethen10seconds.
3) Afterthe10secondstheLEDwillbeginaslowconstantflash.
4) Atthispointpressandholdthe“VolumeUp”buttononthesteeringwheelfor7secondsuntiltheLEDgoessolidred.Nowreleasethe“VolumeUp”buttonandtheLEDgoes“off”.“VolumeUp”hasnowbeenprogrammed.
Section 3: Troubleshooting
5) Nowpressandholdthe“VolumeDown”buttonuntiltheLEDgoessolidred.ReleasethebuttonandtheLEDwillturn“off”.The“VolumeDown”hasnowbeenprogrammed.
6) AtthispointgototheASWCLegendButtonAssignment(remapping/manualprogramming)section,page19,andcontinuewith“SeekUp/Next”button.
7) Youcanendthishalfoftheprogrammingin2ways:
(1) Afterthelastbuttononyoursteeringwheelhasbeenprogrammed(youdonothavetogothroughthewholelist)holddownthe“VolumeUp”buttonforatleast 10seconds.TheLEDwillgointoaslowconstantblinkmode.
--- Or ---
(2) Afterthe18thbuttonisprogrammedorskippedtheLEDwillgobacktotheslowconstantblinkmode.
Note: If at any time an error is made hold down the reset button on the ASWC for 10 or more seconds. This will restart the manual programming. Go back to Step 4 and start again.
8) Pressandholdthe“VolumeDown”buttonfor5secondstilltheLEDstartstoflashquickly.
9) Releasethe“VolumeDown”button.
10) After4secondsoftheLEDflashingquicklytheLEDwillgooutfor2seconds.
Section 3: Troubleshooting
11) ThentheLEDwillflash,upto11times,dependingonwhatradiotheASWCthinksit’sconnectedto.
12) Makesurethenumberofflashesmatchwhatradioyouhaveinstalled.RefertotheChangingRadioTypesection,pages13-14.
13) IftheLEDflashesmatchtheradiothenholddownthe“VolumeDown”buttonuntiltheLEDgoessolidred.
14)Programmingforthevehicleandtheradioisnowcomplete.Testoutthesteeringwheelcontrolfunctionstomakesureitworkscorrectly.
Changing Radio Type
IftheLEDflashesdonotmatchtheradioyouhaveconnected,youmustmanuallyprogramtheASWCtotellitwhatradioitisconnectedto.
1) Tomanuallyprogramtheaftermarketradio,pressandholdthe“VolumeDown”buttononthesteeringwheelcontroluntiltheLEDgoessolidred,thenrelease“VolumeDown”.
2) AtthispointEclipseisprogrammed.IfyouareusinganEclipseradiogotostep3.Ifyouareusingadifferentradiogotostep4.
3) Pressandhold“VolumeDown”for5seconds.TheLEDwillflashoncethengosolidredindicatingtheprogramminghasfinished.Goenjoyyourradio.
4) IfyouhaveadifferentradiothenEclipse,presstheVolumeUpbuttonagaintilltheLEDgoessolidred,thenrelease“VolumeUp”.YouhavenowprogrammedKenwood.
Section 3: Troubleshooting
5) Hereisthecharttoshowhowmanypressesofthe“VolumeUp”buttonisneededforwhichradioyouaretryingtoprogram:
6) Oncetheradiomanufacturerhasbeenselectedhold“VolumeDown”foratleast5seconds.TheLEDwillflashthenumberoftimeswhichradiowasselectedthentheLEDwillremainontoindicatetheASWChasfinishedprogramming.
Manual Radio Type Programming
Ifonlychangingtheradiotypeisneededthenfollowthisprocedurebelow.
1) Withinthefirst25secondsofturningthekeyon,pressandholdthecar’s“VolumeDown”button.
2) After15secondsofholding“VolumeDown”,theASWC’sredLEDwillgoon.
3) Releasethe“VolumeDown”andtheLEDwillgo“off”.Wearenowinradioprogrammingmode.
Section 3: Troubleshooting
1 Eclipse2 Kenwood3 Clarion“Type1”4 SonyandDual5 JVC6 PioneerandJensen
7 Alpine*8 Visteon9 Valor10
Clarion“Type2”11 METRAOE
4) Pressandreleasethe“VolumeUp”buttonforthedesiredradionumber(pleaserefertotheASWClegend).ForeachpresstheredLED.Itwillgo“on”andthen“off”whenreleasedforfeedback.
5) Whenthedesiredradiotypehasbeenreached,Pressthe“VolumeDown”button.
6) TheLEDwillgoonandwillremainon(approximately3seconds).The ASWC is internally computing and storing this new information.
7) TheLEDwillgo“off”indicatingitiscompleted.
Note: If at any time the user fails to press any button for a period of 10 seconds or more, this programing mode will abort.
Section 3: Troubleshooting
Remapping the SWC (Steering Wheel Control) Buttons
OnceyouhavetheASWCprogrammedyoucanthenchangethesteeringwheelcontrolbuttonassignment(s).Suchas,programingthe“SeekUp”buttonasa“Mute”function.FollowthestepsbelowtoremaptheSWCbuttons:
1) IdeallyhavetheASWCvisible,soyoucanseetheLEDflashestoconfirmbuttonrecognition.
2) Turning“off”theradioisrecommended.
3) Withinthefirst20secondsofturningtheignitionon,pressandholddownthe“VolumeUp”buttonforatleast20seconds.
4) TheLEDwilllightupsolidred.Release“VolumeUp”andtheLEDwillgoout.“VolumeUp”hasnowbeenprogrammed.
5) FollowthelistintheButtonAssignmentsection,page19,toreferencetheorderofwhatbuttonsneedtobepressedand/orhowtobypassabutton.
6) Afterthelastbuttonisprogrammedonyoursteeringwheel(youdonothavetogothroughthewholelist),holddownthe“VolumeUp”buttonforatleast10secondsthentheLEDwillgoout.
--- Or ---
Afterthe18thbuttonisprogrammedorskippedtheLEDwillgooutandtheremappingiscompleted.
Section 4: Remapping
Resetting Orginal SWC Settings
Ifforanyreasonafterremappingthesteeringwheelcontrolsyouwanttorevertbacktotheoriginalsteeringwheelcontrolsettings,followthesesteps:
1) Withinthefirst20secondsofturningtheignitionon.Pressandholddowntheoriginal“VolumeDown”button(notthe“VolumeDown”buttonyoujustremapped)foratleast25seconds.
2) TheLEDwillturnonthenreleasethe“VolumeDown”buttonandtheLEDwillturn“off”.
3) Theoriginalsteeringwheelcontrolsettingswillberestored.
Section 4: Remapping
For A and B: Short flashesrepresentthesteeringwheelcontrolwire(s)thatarenotconnectedtothevehiclefromtheASWC.Long flashesrepresentwire(s)thatareconnectedtothevehicle.
A. Vehicle LED Feedback 1stLEDflashistheWhite/GreenwireontheASWC
2ndLEDflashistheOrange/GreenwireontheASWC
3rdLEDflashistheGreen/OrangewireontheASWC
4thLEDflashistheGray/RedwireontheASWC
5thLEDflashistheBlack/Greenwire ontheASWC
6thLEDflashistheGray/BluewireontheASWC
7thLEDflashisthePinkwireontheASWC
B. Radio LED Feedback 1stLEDflashisforEclipse
2ndLEDflashisforKenwood
3rdLEDflashisforClarion(“Type”1)
4thLEDflashisforSonyandDual
5thLEDflashisforJVC
6thLEDflashisforPioneerandJensen
7thLEDflashisforAlpine*
8thLEDflashisforVisteon
9thLEDflashisforValor
10thLEDflashisforClarion(“Type”2)
11thLEDflashisforMetraOE
ASWC Ledgend
C. Button Assignment(remapping/manualprogramming)
ASWC Ledgend
1.VolumeUp
2.VolumeDown
3.SeekUp/Next
4.SeekDown/Prev
5.Source/Mode
6.Mute
7.PresetUp
8.PresetDown
9.Power
10.Band
11.Play/Enter
12.PTT(PushToTalk)
13.OnHook
14.OffHook
15.FanUp
16.FanDown
17.TempUp
18.TempDown
Note: Not all radios will have all of these commands. Please refer to the radio owner’s manual or contact the radio vendor directly for specific commands recognized by that particular radio.
If the next function on the list is not on the steering wheel press the “Volume Up” button for 1 second, until the LED comes on, then release the button. This tells the ASWC that the function is not available will move on to the next function.
*Note (section B): If the ASWC flashes 7 times and you do not have an Alpine radio connected to it that means that the ASWC did not see any radio connected. Verify the 3.5 mm connector is connected to the SWC input on the radio.
INSTALLATION INSTRUCTIONS FOR PART ASWC
IMPORTANT WARNING
Thisproductincludesinstructionsforinstallationwhichmustbecarefullyfollowed.Theinstructionsarewordedinsuchamannertoassumethattheinstalleriscapableofcompletingthesetypeofelectronicinstallations.Ifyouareunclearastowhatyouareinstructedtodoorbelievethatyoudonotunderstandtheinstructionssoastoproperlyandsafelycompletetheinstallationyou should consult a technician who does have this knowledge and understanding.
AXXESS ACCESSORIES STEREOS